DF005 THRU DF10 AND DB101 THRU DB107 SILICON BRIDGE RECTIFIERS Reverse Voltage - 50 to 1000 Volts Forward Current - 1.0 Ampere FEATURES DB-1 The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 Ideal for printed circuit boards Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260 C/10 seconds,5 lbs. (2.3kg) tension + 0.255(6.5) 0.350(8.9) 0.245(6.2) 0.300(7.6) 0.365(9.3) 0.355(9.0) MECHANICAL DATA 0.135(3.4) 0.115(2.9) 0.165(4.2) 0.155(3.9) 0.020 Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting Position: Any Weight:0.04 ounce, 1.0 grams (0.5) 0.060 0.205(5.2) (1.5) 0.195(5.0) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load, for current capacitive load derate by 20%. SYMBOLS Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward output rectified current 0.06”(1.5mm) lead lenth at TA=40 C (Note 2) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Rating for Fusing(t<8.3ms) Maximum instantaneous forward voltage drop per birdge element at 1.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Operating junction temperature range storage temperature range VRRM VRMS VDC DF005 DF01 DF02 DF04 DF06 DF08 DF10 DB101 DB102 DB103 DB104 DB105 DB106 DB107 UNITS 50 100 200 400 600 800 1000 VOLTS 35 70 140 280 420 560 700 VOLTS 50 100 200 400 600 800 1000 VOLTS I(AV) 1.0 Amps IFSM 50.0 Amps I2t 10 A2s VF 1.1 Volts 10 0.5 25 40 -65 to +150 -65 to +150 uA mA pF C/W C C IR CJ RqJA TJ TSTG NOTES: 1.Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2.Unit mounted on P.C. board with 0.51” x 0.51”(13x13mm) copper pads. www.shunyegroup.com.cn RATINGS AND CHARACTERISTIC CURVES DF005 THRU DF10 AND DB101 THRU DB107 AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1- FORWARD CURRENT DERATING CURVE 0.8 0.6 Single Phase Half Wave 60Hz Resistive or inductive Load 0.4 0.2 0 0 25 50 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 £PEAK FORWARD SURGE CURRENT, AMPERES 1.0 75 100 125 150 40 30 20 10 175 0 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 AMBIENT TEMPERATURE, C FIG. 4-TYPICAL REVERSE CHARACTERISTICS FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 1,000 10 1 TJ=25 C PULSE WIDTH=300 ms 1%DUTY CYCLE 0.1 0.01 0.6 0.8 1.0 1.2 1.4 1.5 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES 20 100 10 TJ=25 C 0.1 0.01 0 20 40 60 80 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE TRANSIENT THERMAL IMPEDANCE, C/W FIG. 5-TYPICAL JUNCTION CAPACITANCE TJ=25 C 10 100 10 1 0.1 0.01 0.1 1 10 1 0.1 1.0 10 100 REVERSE VOLTAGE,VOLTS 100 PERCENT OF PEAK REVERSE VOLTAGE,% 200 100 TJ=100 C 1 INSTANTANEOUS FORWARD VOLEAGE, VOLTS JUNCTION CAPACITANCE, pF 100 NUMBER OF CYCLES AT 60 Hz t,PULSE DURATION,sec. www.shunyegroup.com.cn 100