Advanced A/D Flash MCU with LCD & EEPROM HT67F2350/HT67F2360 HT67F2370/HT67F2390 Revision: V1.00 Date: ����������������� December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Table of Contents Features............................................................................................................. 7 CPU Features.......................................................................................................................... 7 Peripheral Features.................................................................................................................. 7 General Description.......................................................................................... 8 Selection Table.................................................................................................. 8 Block Diagram................................................................................................... 9 Pin Assignment................................................................................................. 9 Pin Descriptions............................................................................................. 14 Absolute Maximum Ratings........................................................................... 40 D.C. Characteristics........................................................................................ 40 Operating Voltage Characteristics.......................................................................................... 40 Standby Current Characteristics............................................................................................ 41 Operating Current Characteristics.......................................................................................... 42 A.C. Characteristics........................................................................................ 43 High Speed Internal Oscillator – HIRC – Frequency Accuracy.............................................. 43 Low Speed Internal Oscillator Characteristics – LIRC........................................................... 43 Low Speed Crystal Oscillator Characteristics – LXT.............................................................. 43 Operating Frequency Characteristic Curves.......................................................................... 44 System Start Up Time Characteristics................................................................................... 44 Input/Output Characteristics......................................................................... 45 Memory Characteristics................................................................................. 46 LVD/LVR Electrical Characteristics............................................................... 46 A/D Converter Characteristics....................................................................... 47 Comparator Electrical Characteristics......................................................... 48 LCD Driver Electrical Characteristics........................................................... 49 I2C Characteristics.......................................................................................... 49 Power-on Reset Characteristics.................................................................... 50 System Architecture....................................................................................... 51 Clocking and Pipelining.......................................................................................................... 51 Program Counter.................................................................................................................... 52 Stack...................................................................................................................................... 53 Arithmetic and Logic Unit – ALU............................................................................................ 53 Flash Program Memory.................................................................................. 54 Structure................................................................................................................................. 54 Special Vectors...................................................................................................................... 54 Look-up Table......................................................................................................................... 54 Table Program Example......................................................................................................... 56 In Circuit Programming – ICP................................................................................................ 57 On-Chip Debug Support – OCDS.......................................................................................... 58 Rev. 1.00 2 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM In Application Programming – IAP......................................................................................... 58 Data Memory................................................................................................... 67 Structure................................................................................................................................. 67 Data Memory Addressing....................................................................................................... 68 General Purpose Data Memory............................................................................................. 68 Special Purpose Data Memory.............................................................................................. 68 Special Function Register Description......................................................... 72 Indirect Addressing Registers – IAR0, IAR1, IAR2................................................................ 72 Memory Pointers – MP0, MP1H/MP1L, MP2H/MP2L............................................................ 72 Program Memory Bank Pointer – PBP................................................................................... 74 Accumulator – ACC................................................................................................................ 75 Program Counter Low Register – PCL................................................................................... 75 Look-up Table Registers – TBLP, TBHP, TBLH...................................................................... 75 Status Register – STATUS..................................................................................................... 75 EEPROM Data Memory................................................................................... 77 EEPROM Data Memory Structure......................................................................................... 77 EEPROM Registers............................................................................................................... 77 Reading Data from the EEPROM.......................................................................................... 79 Writing Data to the EEPROM................................................................................................. 80 Write Protection...................................................................................................................... 80 EEPROM Interrupt................................................................................................................. 80 Programming Considerations................................................................................................. 81 Oscillators....................................................................................................... 82 Oscillator Overview................................................................................................................ 82 System Clock Configurations................................................................................................. 82 External Crystal/Ceramic Oscillator – HXT............................................................................ 83 Internal High Speed RC Oscillator – HIRC............................................................................ 84 External 32.768 kHz Crystal Oscillator – LXT........................................................................ 84 Internal 32kHz Oscillator – LIRC............................................................................................ 85 Operating Modes and System Clocks.......................................................... 85 System Clocks....................................................................................................................... 85 System Operation Modes....................................................................................................... 87 Control Registers................................................................................................................... 88 Operating Mode Switching..................................................................................................... 91 Standby Current Considerations............................................................................................ 95 Wake-up................................................................................................................................. 95 Watchdog Timer.............................................................................................. 96 Watchdog Timer Clock Source............................................................................................... 96 Watchdog Timer Control Register.......................................................................................... 96 Watchdog Timer Operation.................................................................................................... 97 Reset and Initialisation................................................................................... 98 Reset Functions..................................................................................................................... 98 Reset Initial Conditions........................................................................................................ 102 Rev. 1.00 3 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Input/Output Ports.........................................................................................110 Pull-high Resistors................................................................................................................112 Port A Wake-up.....................................................................................................................112 I/O Port Control Registers.....................................................................................................113 I/O Port Source Current Control............................................................................................113 Pin-shared Functions............................................................................................................117 I/O Pin Structures................................................................................................................. 130 READ PORT Function......................................................................................................... 131 Programming Considerations............................................................................................... 132 Timer Modules – TM..................................................................................... 133 Introduction.......................................................................................................................... 133 TM Operation....................................................................................................................... 133 TM Clock Source.................................................................................................................. 133 TM Interrupts........................................................................................................................ 134 TM External Pins.................................................................................................................. 134 TM Input/Output Pin Selection............................................................................................. 135 Programming Considerations............................................................................................... 136 Standard Type TM – STM............................................................................. 137 Standard TM Operation........................................................................................................ 137 Standard Type TM Register Description.............................................................................. 138 Standard Type TM Operation Modes................................................................................... 142 Periodic Type TM – PTM............................................................................... 152 Periodic TM Operation......................................................................................................... 153 Periodic Type TM Register Description................................................................................ 153 Periodic Type TM Operation Modes..................................................................................... 158 Analog to Digital Converter......................................................................... 167 A/D Overview....................................................................................................................... 167 Registers Descriptions......................................................................................................... 168 A/D Converter Reference Voltage........................................................................................ 172 A/D Converter Input Signals................................................................................................. 173 A/D Operation...................................................................................................................... 174 Conversion Rate and Timing Diagram................................................................................. 175 Summary of A/D Conversion Steps...................................................................................... 176 Programming Considerations............................................................................................... 177 A/D Transfer Function.......................................................................................................... 177 A/D Programming Examples................................................................................................ 178 Serial Interface Module – SIM...................................................................... 180 SPI Interface........................................................................................................................ 180 I2C Interface......................................................................................................................... 186 Serial Interface – SPIA.................................................................................. 196 SPIA Interface Operation..................................................................................................... 196 SPIA Registers..................................................................................................................... 197 SPIA Communication........................................................................................................... 200 SPIA Bus Enable/Disable..................................................................................................... 202 Rev. 1.00 4 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SPIA Operation.................................................................................................................... 202 Error Detection..................................................................................................................... 203 UART Interface.............................................................................................. 204 UART External Pin............................................................................................................... 205 UART Data Transfer Scheme.............................................................................................. 205 UART Status and Control Registers.................................................................................... 205 Baud Rate Generator........................................................................................................... 210 UART Setup and Control......................................................................................................211 UART Transmitter................................................................................................................ 212 UART Receiver.................................................................................................................... 214 Managing Receiver Errors................................................................................................... 215 UART Interrupt Structure..................................................................................................... 216 UART Power Down and Wake-up........................................................................................ 218 Comparators................................................................................................. 219 Comparator Operation......................................................................................................... 219 Comparator Registers.......................................................................................................... 219 Input Offset Calibration........................................................................................................ 221 Comparator Interrupt............................................................................................................ 221 Programming Considerations............................................................................................... 221 LCD Driver..................................................................................................... 222 LCD Memory........................................................................................................................ 224 LCD Clock Source................................................................................................................ 225 LCD Register........................................................................................................................ 225 LCD Voltage Source and Biasing......................................................................................... 227 LCD Reset Function............................................................................................................. 228 LCD Driver Output................................................................................................................ 229 Programming Considerations............................................................................................... 238 16-bit Multiplication Division Unit – MDU................................................... 239 MDU Registers..................................................................................................................... 239 MDU Operation.................................................................................................................... 240 Cyclic Redundancy Check – CRC............................................................... 242 CRC Registers..................................................................................................................... 242 CRC Operation..................................................................................................................... 243 Low Voltage Detector – LVD........................................................................ 245 LVD Register........................................................................................................................ 245 LVD Operation...................................................................................................................... 246 Interrupts....................................................................................................... 247 Interrupt Registers................................................................................................................ 247 Interrupt Operation............................................................................................................... 257 External Interrupt.................................................................................................................. 259 Multi-function Interrupt......................................................................................................... 259 A/D Converter Interrupt........................................................................................................ 259 TM Interrupt.......................................................................................................................... 260 LVD Interrupt........................................................................................................................ 260 Rev. 1.00 5 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM EEPROM Interrupt............................................................................................................... 260 Serial Interface Module Interrupt.......................................................................................... 260 SPIA Interface Interrupt........................................................................................................ 261 UART Transfer Interrupt....................................................................................................... 261 Comparator Interrupt............................................................................................................ 261 Time Base Interrupt.............................................................................................................. 262 Interrupt Wake-up Function.................................................................................................. 264 Programming Considerations............................................................................................... 264 Application Circuits...................................................................................... 265 Instruction Set............................................................................................... 266 Introduction.......................................................................................................................... 266 Instruction Timing................................................................................................................. 266 Moving and Transferring Data.............................................................................................. 266 Arithmetic Operations........................................................................................................... 266 Logical and Rotate Operation.............................................................................................. 267 Branches and Control Transfer............................................................................................ 267 Bit Operations...................................................................................................................... 267 Table Read Operations........................................................................................................ 267 Other Operations.................................................................................................................. 267 Instruction Set Summary............................................................................. 268 Table Conventions................................................................................................................ 268 Extended Instruction Set...................................................................................................... 270 Instruction Definition.................................................................................... 272 Extended Instruction Definition............................................................................................ 281 Package Information.................................................................................... 288 48-pin LQFP (7mm × 7mm) Outline Dimensions................................................................. 289 64-pin LQFP (7mm × 7mm) Outline Dimensions................................................................. 290 80-pin LQFP (10mm×10mm) Outline Dimensions............................................................... 291 Rev. 1.00 6 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Features CPU Features • Operating Voltage: ♦♦ fSYS=8MHz: 2.2V~5.5V ♦♦ fSYS=12MHz: 2.7V~5.5V ♦♦ fSYS=16MHz: 3.3V~5.5V • Up to 0.25μs instruction cycle with 16MHz system clock at VDD=5V • Power down and wake-up functions to reduce power consumption • Oscillator Types: ♦♦ External High Speed Crystal – HXT ♦♦ Internal High Speed RC – HIRC ♦♦ External 32.768kHz Crystal – LXT ♦♦ Internal 32kHz RC – LIRC • Fully integrated internal 8/12/16 MHz oscillator requires no external components • Multi-mode operation: FAST, SLOW, IDLE and SLEEP • All instructions executed in one to three instruction cycles • Table read instructions • 115 powerful instructions • 16-level subroutine nesting • Bit manipulation instruction Peripheral Features • • • • • • • • • • • • • • • • • • • • • Rev. 1.00 Program Memory: Up to 64K×16 Data Memory: Up to 4096×8 True EEPROM Memory: Up to 1024×8 Watchdog Timer function Up to 71 bidirectional I/O lines Programmable I/O source current LCD Driver function with 1/3 or 1/4 bias Four external interrupt lines shared with I/O pins Multiple Timer Modules for time measure, input capture, compare match output, PWM output function or single pulse output function Serial Interface Module – includes SPI and I2C Additional Serial Peripheral Interface – SPIA Up to three Fully-duplex Universal Asynchronous Receiver and Transmitter Interfaces – UARTs Dual Time-Base functions for generation of fixed time interrupt signals Dual comparator functions Up to 16 external channel 12-bit resolution A/D converter Integrated Multiplier/Divider Unit – MDU Integrated 16-bit Cyclic Redundancy Check function – CRC Low voltage reset function Low voltage detect function European standard IEC 60730 and U.S. UL 60730 certified Wide range of package types 7 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM General Description This series of devices are LCD type Flash Memory 8-bit high performance RISC architecture microcontrollers which are designed for a wide range of applications. Offering users the convenience of Flash Memory multi-programming features, these devices also include a wide range of functions and features. Other memory includes an area of RAM Data Memory as well as an area of true EEPROM memory for storage of non-volatile data such as serial number, calibration data, etc. Analog features include a multi-channel 12-bit A/D converter and dual comparator functions. Multiple and extremely flexible Timer Modules provide timing, pulse generation and PWM generation functions. Communication with the outside world is catered for by including fully integrated SPI, UART or I2C interface functions, three popular interfaces which provide designers with a means of easy comminucation with external peripheral hardware. Protective features such as an internal Watchdog Timer, Low Voltage Reset and Low Voltage Detector coupled with excellent noise immunity and ESD protection ensure that reliable operation is maintained in hostile electrical environments. A full choice of HXT, LXT, HIRC and LIRC oscillator functions are provided including a fully integrated system oscillator which requires no external components for its implementation. The ability to operate and switch dynamically between a range of operating modes using different clock sources gives users the ability to optimise microcontroller operation and minimise power consumption. The inclusion of flexible I/O programming features, Time-Base functions along with many other features ensure that the devices will find excellent use in applications such as electronic metering, environmental monitoring, handheld instruments, household appliances, electronically controlled tools, motor driving in addition to many others. Selection Table Most features are common to all devices. The main features distinguishing them are Memory capacity, I/O count, A/D converter channel number, LCD driver pin count and UART interface number. The following table summarises the main features of each device. Part No. Program Memory Data Memory Data EEPROM I/O External Interrupt A/D LCD Driver Timer Module (SEGm × COMn) HT67F2350 8k × 16 768 × 8 256 × 8 57 4 12-bit × 12 46 × 4 44 × 6 42 × 8 10-bit PTM × 6 16-bit PTM × 2 16-bit STM × 3 HT67F2360 16k × 16 1536 × 8 256 × 8 71 4 12-bit × 16 56 × 4 54 × 6 52 × 8 10-bit PTM × 6 16-bit PTM × 2 16-bit STM × 3 HT67F2370 32k × 16 3072 × 8 512 × 8 71 4 12-bit × 16 56 × 4 54 × 6 52 × 8 10-bit PTM × 6 16-bit PTM × 2 16-bit STM × 3 HT67F2390 64k × 16 4096 × 8 1024 × 8 71 4 12-bit × 16 56 × 4 54 × 6 52 × 8 10-bit PTM × 6 16-bit PTM × 2 16-bit STM × 3 Part No. Time Base Comparators Stacks SIM SPIA UART MDU CRC Package HT67F2350 2 2 16 √ √ 2 √ √ 48/64LQFP HT67F2360 2 2 16 √ √ 2 √ √ 64/80LQFP HT67F2370 2 2 16 √ √ 3 √ √ 64/80LQFP HT67F2390 2 2 16 √ √ 3 √ √ 64/80LQFP Note: As devices exist in more than one package format, the table reflects the situation for the package with the most pins. Rev. 1.00 8 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Block Diagram Low Voltage Dete�t Flash/EEPROM P�og�a��ing Ci��uit�y Low Voltage Reset MDU EEPROM Data Me�o�y Flash P�og�a� Me�o�y IAP Reset Ci��uit Inte��upt Cont�olle� 8-�it RISC MCU Co�e Exte�nal HXT/LXT Os�illato�s CRC RAM Data Me�o�y Ti�e Base Wat�hdog Ti�e� Inte�nal HIRC/LIRC Os�illato�s 1�-�it A/D Conve�te� Co�pa�ato�s I/Os Ti�e� Modules SIM (SPI/I�C) UARTs SPIA LCD D�ive� Pin Assignment PD1/STCK1/RX1/AN9/SEG44 AVDD PF4/PTCK0/XT2 PF5/PTP0I/PTP0/XT1 AVSS PD2/PTP2I/PTP2/TX1/AN10 PD3/PTCK2/PTP7I/PTP7/AN11/SEG43 PF6/STCK2/RX1/C0−/SEG37 PF7/STP2I/STP2/TX1/C0+ PB5/RES/SEG36 VDD VSS PB6/STP1I/STP1/OSC1/SEG35 PB7/STCK1/OSC2/SEG34 PA0/SEG30/ICPDA/OCDSDA PA2/SEG29/ICPCK/OCDSCK PA1/INT0/SCS/SEG26 PA3/INT1/SDO/SEG25 PA4/INT2/SDI/SDA/SEG24 PA5/INT3/SCK/SCL/SEG23 PA6/INT0/RX0/SEG22 PA7/INT1/TX0/SEG21 PB2/PTP3I/PTCK2/PTP3/SEG16 PE0/STCK0/SCSA/SEG7 48 47 46 45 44 43 42 41 40 39 38 37 36 1 35 2 34 3 33 4 5 32 HT67F2350/HT67V2350 31 6 7 30 48 LQFP-A 29 8 28 9 27 10 26 11 25 12 13 14 15 16 17 18 19 20 21 22 23 24 PD0/INT2/STP1I/STP1/AN8/SEG45 PC7/INT3/STCK0/PTP6I/PTP6/AN7/SEG46 PC5/PTCK1/PTP5I/PTP5/AN5/SEG48 PC3/PTCK0/PTP4I/PTP4/AN3/SEG50 PC1/C0X/VREF/AN1 PC0/VREFI/AN0/SEG52 PLCD VMAX V1 PE7/V2/SEG53 PE6/C1/SEG54 PE5/C2/SEG55 PG4/COM0 PG5/COM1 PG6/COM2 PG7/COM3 PJ0/COM4/SEG0 PJ1/COM5/SEG1 PJ2/COM6/SEG2 PJ3/COM7/SEG3 PE4 PE3/PTP1I/PTP1/SCKA/SEG4 PE2/PTCK1/SDIA/SEG5 PE1/STP0I/STP0/SDOA/SEG6 Rev. 1.00 9 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM AVDD PF4/PTCK0/XT2 PF5/PTP0I/PTP0/XT1 AVSS PD2/PTP2I/PTP2/TX1/AN10 PD3/PTCK2/PTP7I/PTP7/AN11/SEG43 PD4/PTP3I/PTP3/RX0/C1− PD5/PTCK3/TX0/C1+/SEG38 PF6/STCK2/RX1/C0−/SEG37 PF7/STP2I/STP2/TX1/C0+ PB5/RES/SEG36 VDD VSS PB6/STP1I/STP1/OSC1/SEG35 PB7/STCK1/OSC2/SEG34 PD6/STP2I/STP2/C1X/SEG33 PB0/STCK2/C0X/SEG32 PB1/PTCK3/SEG31 PA0/SEG30/ICPDA/OCDSDA PA2/SEG29/ICPCK/OCDSCK PB4/C1X/SEG28 PB3/PTP2I/PTP2/SEG27 PA1/INT0/SCS/SEG26 PA3/INT1/SDO/SEG25 PA4/INT2/SDI/SDA/SEG24 PA5/INT3/SCK/SCL/SEG23 PA6/INT0/RX0/SEG22 PA7/INT1/TX0/SEG21 PB2/PTP3I/PTCK2/PTP3/SEG16 PF0/SCS/SEG15 PF1/SDO/SEG14 PF2/SDI/SDA/SEG13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 HT67F2350/HT67V2350 41 HT67F2360/HT67V2360 40 64 LQFP-A 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PG4/COM0 PG5/COM1 PG6/COM2 PG7/COM3 PJ0/COM4/SEG0 PJ1/COM5/SEG1 PJ2/COM6/SEG2 PJ3/COM7/SEG3 PE4 PE3/PTP1I/PTP1/SCKA/SEG4 PE2/PTCK1/SDIA/SEG5 PE1/STP0I/STP0/SDOA/SEG6 PE0/STCK0/SCSA/SEG7 PJ6/PTCK5/SEG10 PJ7/PTCK4/SEG11 PF3/SCK/SCL/SEG12 Rev. 1.00 PD1/STCK1/RX1/AN9/SEG44 PD0/INT2/STP1I/STP1/AN8/SEG45 PC7/INT3/STCK0/PTP6I/PTP6/AN7/SEG46 PC6/STP0I/STP0/AN6/SEG47 PC5/PTCK1/PTP5I/PTP5/AN5/SEG48 PC4/PTP1I/PTP1/AN4/SEG49 PC3/PTCK0/PTP4I/PTP4/AN3/SEG50 PC2/PTP0I/PTP0/AN2/SEG51 PC1/C0X/VREF/AN1 PC0/VREFI/AN0/SEG52 PLCD VMAX V1 PE7/V2/SEG53 PE6/C1/SEG54 PE5/C2/SEG55 10 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM AVDD PF4/PTCK0/XT2 PF5/PTP0I/PTP0/XT1 AVSS PD2/PTP2I/PTP2/TX1/AN10 PD3/PTCK2/PTP7I/PTP7/AN11/SEG43 PH2/PTCK4/AN12/SEG42 PH3/PTCK5/AN13/SEG41 PH4/PTCK6/AN14/SEG40 PH5/PTCK7/AN15/SEG39 PD4/PTP3I/PTP3/RX0/C1− PD5/PTCK3/TX0/C1+/SEG38 PF6/STCK2/RX1/C0−/SEG37 PF7/STP2I/STP2/TX1/C0+ PB5/RES/SEG36 VDD VSS PB6/STP1I/STP1/OSC1/SEG35 PB7/STCK1/OSC2/SEG34 PD6/STP2I/STP2/C1X/SEG33 PB0/STCK2/C0X/SEG32 PB1/PTCK3/SEG31 PA0/SEG30/ICPDA/OCDSDA PA2/SEG29/ICPCK/OCDSCK PB4/C1X/SEG28 PB3/PTP2I/PTP2/SEG27 PA1/INT0/SCS/SEG26 PA3/INT1/SDO/SEG25 PA4/INT2/SDI/SDA/SEG24 PA5/INT3/SCK/SCL/SEG23 PA6/INT0/RX0/SEG22 PA7/INT1/TX0/SEG21 PH0/PTP4I/PTP4/SEG20 PH1/PTP5I/PTP5/SEG19 PH6/PTP6I/PTP6/SEG18 PH7/PTP7I/PTP7/SEG17 PB2/PTP3I/PTCK2/PTP3/SEG16 PF0/SCS/SEG15 PF1/SDO/SEG14 PF2/SDI/SDA/SEG13 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 6463 62 61 60 2 59 3 58 4 57 5 56 6 55 7 54 8 53 9 52 10 51 HT67F2360/HT67V2360 11 40 80 LQFP-A 12 49 13 48 14 47 15 46 16 45 17 44 18 43 19 42 20 41 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 3738 39 40 1 PD1/STCK1/RX1/AN9/SEG44 PD0/INT2/STP1I/STP1/AN8/SEG45 PC7/INT3/STCK0/PTP6I/PTP6/AN7/SEG46 PC6/STP0I/STP0/AN6/SEG47 PC5/PTCK1/PTP5I/PTP5/AN5/SEG48 PC4/PTP1I/PTP1/AN4/SEG49 PC3/PTCK0/PTP4I/PTP4/AN3/SEG50 PC2/PTP0I/PTP0/AN2/SEG51 PC1/C0X/VREF/AN1 PC0/VREFI/AN0/SEG52 PLCD VMAX V1 PE7/V2/SEG53 PE6/C1/SEG54 PE5/C2/SEG55 PG0/COM0 PG1/COM1 PG2/COM2 PG3/COM3 PG4/COM0 PG5/COM1 PG6/COM2 PG7/COM3 PJ0/COM4/SEG0 PJ1/COM5/SEG1 PJ2/COM6/SEG2 PJ3/COM7/SEG3 PE4 PE3/PTP1I/PTP1/SCKA/SEG4 PE2/PTCK1/SDIA/SEG5 PE1/STP0I/STP0/SDOA/SEG6 PE0/STCK0/SCSA/SEG7 VSS VDD PJ4/PTCK7/SEG8 PJ5/PTCK6/SEG9 PJ6/PTCK5/SEG10 PJ7/PTCK4/SEG11 PF3/SCK/SCL/SEG12 Rev. 1.00 11 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM AVDD PF4/PTCK0/XT2 PF5/PTP0I/PTP0/XT1 AVSS PD2/PTP2I/PTP2/TX1/AN10 PD3/PTCK2/PTP7I/PTP7/AN11/SEG43 PD4/PTP3I/PTP3/RX0/C1− PD5/PTCK3/TX0/C1+/SEG38 PF6/STCK2/RX1/C0−/SEG37 PF7/STP2I/STP2/TX1/C0+ PB5/RES/SEG36 VDD VSS PB6/STP1I/STP1/OSC1/SEG35 PB7/STCK1/OSC2/SEG34 PD6/STP2I/STP2/C1X/SEG33 PB0/STCK2/RX2/C0X/SEG32 PB1/PTCK3/TX2/SEG31 PA0/SEG30/ICPDA/OCDSDA PA2/SEG29/ICPCK/OCDSCK PB4/C1X/SEG28 PB3/PTP2I/PTP2/SEG27 PA1/INT0/SCS/SEG26 PA3/INT1/SDO/SEG25 PA4/INT2/SDI/SDA/SEG24 PA5/INT3/SCK/SCL/SEG23 PA6/INT0/RX0/SEG22 PA7/INT1/TX0/SEG21 PB2/PTP3I/PTCK2/PTP3/SEG16 PF0/SCS/SEG15 PF1/SDO/SEG14 PF2/SDI/SDA/SEG13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 HT67F2370/HT67V2370 41 HT67F2390/HT67V2390 40 64 LQFP-A 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 PD1/STCK1/RX1/AN9/SEG44 PD0/INT2/STP1I/STP1/AN8/SEG45 PC7/INT3/STCK0/PTP6I/PTP6/AN7/SEG46 PC6/STP0I/STP0/AN6/SEG47 PC5/PTCK1/PTP5I/PTP5/AN5/SEG48 PC4/PTP1I/PTP1/AN4/SEG49 PC3/PTCK0/PTP4I/PTP4/AN3/SEG50 PC2/PTP0I/PTP0/AN2/SEG51 PC1/C0X/VREF/AN1 PC0/VREFI/AN0/SEG52 PLCD VMAX V1 PE7/V2/SEG53 PE6/C1/SEG54 PE5/C2/SEG55 PG4/COM0 PG5/COM1 PG6/COM2 PG7/COM3 PJ0/COM4/SEG0 PJ1/COM5/SEG1 PJ2/COM6/SEG2 PJ3/COM7/SEG3 PE4 PE3/PTP1I/PTP1/SCKA/SEG4 PE2/PTCK1/SDIA/SEG5 PE1/STP0I/STP0/SDOA/SEG6 PE0/STCK0/SCSA/SEG7 PJ6/PTCK5/SEG10 PJ7/PTCK4/SEG11 PF3/SCK/SCL/SEG12 Rev. 1.00 12 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM AVDD PF4/PTCK0/XT2 PF5/PTP0I/PTP0/XT1 AVSS PD2/PTP2I/PTP2/TX1/AN10 PD3/PTCK2/PTP7I/PTP7/AN11/SEG43 PH2/PTCK4/AN12/SEG42 PH3/PTCK5/AN13/SEG41 PH4/PTCK6/AN14/SEG40 PH5/PTCK7/AN15/SEG39 PD4/PTP3I/PTP3/RX0/C1− PD5/PTCK3/TX0/C1+/SEG38 PF6/STCK2/RX1/C0−/SEG37 PF7/STP2I/STP2/TX1/C0+ PB5/RES/SEG36 VDD VSS PB6/STP1I/STP1/OSC1/SEG35 PB7/STCK1/OSC2/SEG34 PD6/STP2I/STP2/C1X/SEG33 PB0/STCK2/RX2/C0X/SEG32 PB1/PTCK3/TX2/SEG31 PA0/SEG30/ICPDA/OCDSDA PA2/SEG29/ICPCK/OCDSCK PB4/C1X/SEG28 PB3/PTP2I/PTP2/SEG27 PA1/INT0/SCS/SEG26 PA3/INT1/SDO/SEG25 PA4/INT2/SDI/SDA/SEG24 PA5/INT3/SCK/SCL/SEG23 PA6/INT0/RX0/SEG22 PA7/INT1/TX0/SEG21 PH0/PTP4I/PTP4/SEG20 PH1/PTP5I/PTP5/SEG19 PH6/PTP6I/PTP6/SEG18 PH7/PTP7I/PTP7/SEG17 PB2/PTP3I/PTCK2/PTP3/SEG16 PF0/SCS/SEG15 PF1/SDO/SEG14 PF2/SDI/SDA/SEG13 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 6463 62 61 60 2 59 3 58 4 57 5 56 6 55 7 54 8 53 9 52 HT67F2370/HT67V2370 10 51 HT67F2390/HT67V2390 11 40 80 LQFP-A 12 49 13 48 14 47 15 46 16 45 17 44 18 43 19 42 20 41 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 3738 39 40 1 PD1/STCK1/RX1/AN9/SEG44 PD0/INT2/STP1I/STP1/AN8/SEG45 PC7/INT3/STCK0/PTP6I/PTP6/AN7/SEG46 PC6/STP0I/STP0/AN6/SEG47 PC5/PTCK1/PTP5I/PTP5/AN5/SEG48 PC4/PTP1I/PTP1/AN4/SEG49 PC3/PTCK0/PTP4I/PTP4/AN3/SEG50 PC2/PTP0I/PTP0/AN2/SEG51 PC1/C0X/VREF/AN1 PC0/VREFI/AN0/SEG52 PLCD VMAX V1 PE7/V2/SEG53 PE6/C1/SEG54 PE5/C2/SEG55 PG0/RX2/COM0 PG1/TX2/COM1 PG2/COM2 PG3/COM3 PG4/COM0 PG5/COM1 PG6/COM2 PG7/COM3 PJ0/COM4/SEG0 PJ1/COM5/SEG1 PJ2/COM6/SEG2 PJ3/COM7/SEG3 PE4 PE3/PTP1I/PTP1/SCKA/SEG4 PE2/PTCK1/SDIA/SEG5 PE1/STP0I/STP0/SDOA/SEG6 PE0/STCK0/SCSA/SEG7 VSS VDD PJ4/PTCK7/SEG8 PJ5/PTCK6/SEG9 PJ6/PTCK5/SEG10 PJ7/PTCK4/SEG11 PF3/SCK/SCL/SEG12 Note: The OCDSDA and OCDSCK pins are the OCDS dedicated pins and only available for the HT67V23x0 device which is the OCDS EV chip for the HT67F23x0 device. Rev. 1.00 13 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pin Descriptions With the exception of the power pins, all pins on these devices can be referenced by their Port name, e.g. PA0, PA1, etc., which refer to the digital I/O function of the pins. However these Port pins are also shared with other function such as the Analog to Digital Converter, Timer Module pins, etc. The function of each pin is listed in the following table, however the details behind how each pin is configured is contained in other sections of the datasheet. HT67F2350 Pad Name PA0/SEG30/ICPDA/ OCDSDA PA1/INT0/SCS/SEG26 PA2/SEG29/ICPCK/ OCDSCK PA3/INT1/SDO/SEG25 PA4/INT2/SDI/SDA/ SEG24 Rev. 1.00 Function OPT I/T O/T PA0 PAWU PAPU PAS0 ST CMOS SEG30 PAS0 — LCD Description General purpose I/O. Register enabled pull-up and wake-up. LCD segment output ICPDA — ST CMOS ICP Data/Address pin OCDSDA — ST CMOS OCDS Data/Address pin, for EV chip only. PA1 PAWU PAPU PAS0 ST CMOS INT0 PAS0 INTEG INTC0 IFS2 ST — SCS PAS0 IFS2 ST SEG26 PAS0 — LCD PA2 PAWU PAPU PAS0 ST CMOS SEG29 PAS0 — ICPCK — ST OCDSCK — ST — PA3 PAWU PAPU PAS0 ST CMOS INT1 PAS0 INTEG INTC0 IFS2 ST — SDO PAS0 — SEG25 PAS0 — LCD PA4 PAWU PAPU PAS1 ST CMOS INT2 PAS1 INTEG INTC3 IFS2 ST — External Interrupt 2 SDI PAS1 IFS2 ST — SPI data input SDA PAS1 IFS2 ST SEG24 PAS1 — General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 0 CMOS SPI slave select LCD LCD segment output General purpose I/O. Register enabled pull-up and wake-up. LCD segment output CMOS ICP Clock pin OCDS Clock pin, for EV chip only. General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 1 CMOS SPI data output LCD segment output General purpose I/O. Register enabled pull-up and wake-up. NMOS I2C data line LCD 14 LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PA5/INT3/SCK/SCL/ SEG23 PA6/INT0/RX0/SEG22 PA7/INT1/TX0/SEG21 PB0/STCK2/C0X/SEG32 PB1/PTCK3/SEG31 PB2/PTP3I/PTCK2/ PTP3/SEG16 Rev. 1.00 Function OPT I/T O/T PA5 PAWU PAPU PAS1 ST CMOS INT3 PAS1 INTEG INTC3 IFS2 ST — SCK PAS1 IFS2 ST CMOS SPI serial clock SCL PAS1 IFS2 ST NMOS I2C clock line SEG23 PAS1 — LCD PA6 PAWU PAPU PAS1 ST CMOS INT0 PAS1 INTEG INTC0 IFS2 ST — External Interrupt 0 RX0 PAS1 IFS4 ST — UART0 RX serial data input SEG22 PAS1 — LCD PA7 PAWU PAPU PAS1 ST CMOS INT1 PAS1 INTEG INTC0 IFS2 ST — TX0 PAS1 — SEG21 PAS1 — PB0 PBPU PBS0 ST STCK2 PBS0 IFS0 ST Description General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 3 LCD segment output General purpose I/O. Register enabled pull-up and wake-up. LCD segment output General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 1 CMOS UART0 TX serial data output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM2 clock input C0X PBS0 — SEG32 PBS0 — CMOS Comparator 0 output PB1 PBPU PBS0 ST PTCK3 PBS0 IFS0 ST — SEG31 PBS0 — LCD PB2 PBPU PBS0 ST PTP3I PBS0 IFS1 ST — PTM3 capture input PTCK2 PBS0 IFS0 ST — PTM2 clock input PTP3 PBS0 — SEG16 PBS0 — LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTM3 clock input LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS PTM3 output LCD 15 LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PB3/PTP2I/PTP2/SEG27 PB4/C1X/SEG28 PB5/RES/SEG36 PB6/STP1I/STP1/OSC1/ SEG35 PB7/STCK1/OSC2/ SEG34 PC0/VREFI/AN0/SEG52 PC1/C0X/VREF/AN1 PC2/PTP0I/PTP0/AN2/ SEG51 Rev. 1.00 Function OPT I/T PB3 PBPU PBS0 ST PTP2I PBS0 IFS1 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. — PTM2 capture input PTP2 PBS0 — SEG27 PBS0 — CMOS PTM2 output PB4 PBPU PBS1 ST CMOS General purpose I/O. Register enabled pull-up. CMOS Comparator 1 output LCD LCD segment output C1X PBS1 — SEG28 PBS1 — PB5 PBPU PBS1 RSTC ST RES RSTC ST — External reset input SEG36 PBS1 RSTC — LCD LCD segment output PB6 PBPU PBS1 ST STP1I PBS1 IFS1 ST LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS General purpose I/O. Register enabled pull-up. — STP1 PBS1 — OSC1 PBS1 HXT — SEG35 PBS1 — LCD PB7 PBPU PBS1 ST STCK1 PBS1 IFS0 ST STM1 capture input CMOS STM1 output HXT oscillator pin LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM1 clock input OSC2 PBS1 — HXT HXT oscillator pin SEG34 PBS1 — LCD LCD segment output PC0 PCPU PCS0 ST CMOS General purpose I/O. Register enabled pull-up. VREFI PCS0 AN — A/D Converter reference voltage input AN0 PCS0 AN — A/D Converter analog input SEG52 PCS0 — LCD PC1 PCPU PCS0 ST CMOS General purpose I/O. Register enabled pull-up. C0X PCS0 — CMOS Comparator 0 output VREF PCS0 AN — A/D Converter reference voltage input AN1 PCS0 AN — A/D Converter analog input PC2 PCPU PCS0 ST PTP0I PCS0 IFS1 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTP0 PCS0 — AN2 PCS0 AN — SEG51 PCS0 — LCD PTM0 capture input CMOS PTM0 output 16 A/D Converter analog input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PC3/PTCK0/PTP4I/ PTP4/AN3/SEG50 PC4/PTP1I/PTP1/AN4/ SEG49 PC5/PTCK1/PTP5I/ PTP5/AN5/SEG48 PC6/STP0I/STP0/AN6/ SEG47 PC7/INT3/STCK0/PTP6I/ PTP6/AN7/SEG46 Rev. 1.00 Function OPT I/T PC3 PCPU PCS0 ST PTCK0 PCS0 IFS0 ST PTP4I PCS0 ST PTP4 PCS0 — O/T Description CMOS General purpose I/O. Register enabled pull-up. — PTM0 clock input — PTM4 capture input CMOS PTM4 output AN3 PCS0 AN — SEG50 PCS0 — LCD PC4 PCPU PCS1 ST PTP1I PCS1 IFS1 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTP1 PCS1 — AN4 PCS1 AN — SEG49 PCS1 — LCD PC5 PCPU PCS1 ST PTCK1 PCS1 IFS0 ST PTP5I PCS1 ST PTP5 PCS1 — PTM1 capture input CMOS PTM1 output A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM1 clock input — PTM5 capture input CMOS PTM5 output AN5 PCS1 AN — SEG48 PCS1 — LCD PC6 PCPU PCS1 ST STP0I PCS1 IFS1 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 capture input STP0 PCS1 — AN6 PCS1 AN CMOS STM0 output — SEG47 PCS1 — LCD PC7 PCPU PCS1 ST INT3 PCS1 INTEG INTC3 IFS2 ST — External Interrupt 3 STCK0 PCS1 IFS0 ST — STM0 clock input PTP6I PCS1 ST — PTM6 capture input PTP6 PCS1 — AN7 PCS1 AN — SEG46 PCS1 — LCD A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS PTM6 output 17 A/D Converter analog input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PD0/INT2/STP1I/STP1/ AN8/SEG45 PD1/STCK1/RX1/AN9/ SEG44 PD2/PTP2I/PTP2/TX1/ AN10 PD3/PTCK2/PTP7I/ PTP7/AN11/SEG43 PD4/PTP3I/PTP3/RX0/ C1− PD5/PTCK3/TX0/C1+/ SEG38 Rev. 1.00 Function OPT I/T PD0 PDPU PDS0 O/T Description ST INT2 PDS0 INTEG INTC3 IFS2 ST — External Interrupt 2 STP1I PDS0 IFS1 ST — STM1 capture input CMOS General purpose I/O. Register enabled pull-up. STP1 PDS0 — AN8 PDS0 AN CMOS STM1 output — SEG45 PCS1 — LCD PD1 PDPU PDS0 ST STCK1 PDS0 IFS0 ST — STM1 clock input RX1 PDS0 IFS4 ST — UART1 RX serial data input A/D Converter analog input A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. AN9 PDS0 AN — SEG44 PDS0 — LCD PD2 PDPU PDS0 ST PTP2I PDS0 IFS1 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM2 capture input PTP2 PDS0 — CMOS PTM2 output TX1 PDS0 — CMOS UART1 TX serial data output AN10 PDS0 AN PD3 PDPU PDS0 ST PTCK2 PDS0 IFS0 ST — PTM2 clock input PTP7I PDS0 ST — PTM7 capture input — A/D Converter analog input CMOS General purpose I/O. Register enabled pull-up. PTP7 PDS0 — AN11 PDS0 AN CMOS PTM7 output — SEG43 PDS0 — LCD PD4 PDPU PDS1 ST PTP3I PDS1 IFS1 ST PTP3 PDS1 — RX0 PDS1 IFS4 ST — UART0 RX serial data input C1− PDS1 AN — Comparator 1 negative input PD5 PDPU PDS1 ST PTCK3 PDS1 IFS0 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM3 capture input CMOS PTM3 output CMOS General purpose I/O. Register enabled pull-up. — TX0 PDS1 — C1+ PDS1 AN — SEG38 PDS1 — LCD PTM3 clock input CMOS UART0 TX serial data output 18 Comparator 1 positive input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PD6/STP2I/STP2/C1X/ SEG33 PE0/STCK0/SCSA/SEG7 PE1/STP0I/STP0/SDOA/ SEG6 PE2/PTCK1/SDIA/SEG5 PE3/PTP1I/PTP1/SCKA/ SEG4 PE4 PE5/C2/SEG55 PE6/C1/SEG54 PE7/V2/SEG53 PF0/SCS/SEG15 Rev. 1.00 Function OPT I/T PD6 PDPU PDS1 ST STP2I PDS1 IFS1 ST STP2 PDS1 — CMOS STM2 output C1X PDS1 — CMOS Comparator 1 output SEG33 PDS1 — PE0 PEPU PES0 ST STCK0 PES0 IFS0 ST SCSA PES0 ST SEG7 PES0 — PE1 PEPU PES0 ST STP0I PES0 IFS1 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. — LCD STM2 capture input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 clock input CMOS SPIA slave select LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 capture input STP0 PES0 — CMOS STM0 inverted output SDOA PES0 — CMOS SPIA data output SEG6 PES0 — PE2 PEPU PES0 ST PTCK1 PES0 IFS0 ST LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM1 clock input SPIA data input SDIA PES0 ST — SEG5 PES0 — LCD PE3 PEPU PES0 ST PTP1I PES0 IFS1 ST PTP1 PES0 — CMOS PTM1 output SCKA PES0 ST CMOS SPIA serial clock SEG4 PES0 — PE4 PEPU PES1 ST CMOS General purpose I/O. Register enabled pull-up. PE5 PEPU PES1 ST CMOS General purpose I/O. Register enabled pull-up. C2 PES1 — AN SEG55 PES1 — LCD PE6 PEPU PES1 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — LCD PTM1 capture input LCD segment output LCD voltage pump LCD segment output CMOS General purpose I/O. Register enabled pull-up. C1 PES1 — AN SEG54 PES1 — LCD PE7 PEPU PES1 ST LCD voltage pump LCD segment output CMOS General purpose I/O. Register enabled pull-up. V2 PES1 PWR AN SEG53 PES1 — LCD PF0 PFPU PFS0 ST CMOS General purpose I/O. Register enabled pull-up. SCS PFS0 IFS2 ST CMOS SPI slave select SEG15 PFS0 — LCD 19 LCD voltage pump LCD segment output LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PF1/SDO/SEG14 PF2/SDI/SDA/SEG13 PF3/SCK/SCL/SEG12 PF4/PTCK0/XT2 PF5/PTP0I/PTP0/XT1 PF6/STCK2/RX1/C0−/ SEG37 PF7/STP2I/STP2/TX1/ C0+ PG4/COM0 PG5/COM1 Rev. 1.00 Function OPT I/T PF1 PFPU PFS0 O/T Description ST CMOS General purpose I/O. Register enabled pull-up. CMOS SPI data output SDO PFS0 — SEG14 PFS0 — PF2 PFPU PFS0 ST SDI PFS0 IFS2 ST SDA PFS0 IFS2 ST SEG13 PFS0 — PF3 PFPU PFS0 ST CMOS General purpose I/O. Register enabled pull-up. SCK PFS0 IFS2 ST CMOS SPI serial clock SCL PFS0 IFS2 ST NMOS I2C clock line SEG12 PFS0 — PF4 PFPU PFS1 ST PTCK0 PFS1 IFS0 ST — PTM0 clock input XT2 PFS1 — LXT LXT oscillator pin PF5 PFPU PFS1 ST PTP0I PFS1 IFS1 ST PTP0 PFS1 — XT1 PFS1 LXT PF6 PFPU PFS1 ST STCK2 PFS1 IFS0 ST — STM2 clock input RX1 PFS1 IFS4 ST — UART1 RX serial data input Comparator 0 negative input LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — SPI data input NMOS I2C data line LCD LCD LCD segment output LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS General purpose I/O. Register enabled pull-up. — PTM0 capture input CMOS PTM0 output — LXT oscillator pin CMOS General purpose I/O. Register enabled pull-up. C0− PFS1 AN — SEG37 PFS1 — LCD PF7 PFPU PFS1 ST STP2I PFS1 IFS1 ST STP2 PFS1 — CMOS STM2 output TX1 PFS1 — CMOS UART1 TX serial data output C0+ PFS1 AN PG4 PGPU PGS1 ST COM0 PGS1 — PG5 PGPU PGS1 ST COM1 PGS1 — LCD segment output CMOS General purpose I/O. Register enabled pull-up. — — STM2 capture input Comparator 0 positive input CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD 20 LCD common output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PG6/COM2 PG7/COM3 PJ0/COM4/SEG0 PJ1/COM5/SEG1 PJ2/COM6/SEG2 PJ3/COM7/SEG3 PJ6/PTCK5/SEG10 PJ7/PTCK4/SEG11 VDD VSS Function OPT I/T PG6 PGPU PGS1 ST COM2 PGS1 — PG7 PGPU PGS1 ST COM3 PGS1 — PJ0 PJPU PJS0 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. COM4 PJS0 — LCD LCD common output SEG0 PJS0 — LCD LCD segment output PJ1 PJPU PJS0 ST CMOS General purpose I/O. Register enabled pull-up. COM5 PJS0 — LCD LCD common output SEG1 PJS0 — LCD LCD segment output PJ2 PJPU PJS0 ST COM6 PJS0 — LCD LCD common output SEG2 PJS0 — LCD LCD segment output PJ3 PJPU PJS0 ST COM7 PJS0 — LCD LCD common output SEG3 PJS0 — LCD LCD segment output PJ6 PJPU PJS1 ST CMOS General purpose I/O. Register enabled pull-up. CMOS General purpose I/O. Register enabled pull-up. CMOS General purpose I/O. Register enabled pull-up. PTCK5 PJS1 ST — SEG10 PJS1 — LCD PTM5 clock input PJ7 PJPU PJS1 ST PTCK4 PJS1 ST — SEG11 PJS1 — LCD LCD segment output VDD — PWR — Positive power supply LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTM4 clock input VSS — PWR — Negative power supply, ground. AVDD AVDD — PWR — Analog positive power supply AVSS AVSS — PWR — Analog negative power supply, ground. VMAX VMAX — PWR — IC maximum voltage, connected to VDD or V1. V1 — PWR AN LCD voltage pump PLCD — PWR AN LCD power supply V1 PLCD Legend: I/T: Input type; CMOS: CMOS output; ST: Schmitt Trigger input; HXT: High frequency crystal oscillator; LCD: LCD SEG/COM output; Rev. 1.00 O/T: Output type; OPT: Optional by register option; NMOS: NMOS output; AN: Analog signal; LXT: Low frequency crystal oscillator; PWR: Power 21 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM HT67F2360 Pad Name PA0/SEG30/ICPDA/ OCDSDA PA1/INT0/SCS/SEG26 PA2/SEG29/ICPCK/ OCDSCK PA3/INT1/SDO/SEG25 PA4/INT2/SDI/SDA/ SEG24 Rev. 1.00 Function OPT I/T O/T PA0 PAWU PAPU PAS0 ST CMOS SEG30 PAS0 — LCD Description General purpose I/O. Register enabled pull-up and wake-up. LCD segment output ICPDA — ST CMOS ICP Data/Address pin OCDSDA — ST CMOS OCDS Data/Address pin, for EV chip only. PA1 PAWU PAPU PAS0 ST CMOS INT0 PAS0 INTEG INTC0 IFS2 ST — SCS PAS0 IFS2 ST SEG26 PAS0 — LCD PA2 PAWU PAPU PAS0 ST CMOS SEG29 PAS0 — ICPCK — ST OCDSCK — ST — PA3 PAWU PAPU PAS0 ST CMOS INT1 PAS0 INTEG INTC0 IFS2 ST — General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 0 CMOS SPI slave select LCD LCD segment output General purpose I/O. Register enabled pull-up and wake-up. LCD segment output CMOS ICP Clock pin OCDS Clock pin, for EV chip only. General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 1 SDO PAS0 — SEG25 PAS0 — CMOS SPI data output LCD PA4 PAWU PAPU PAS1 ST CMOS INT2 PAS1 INTEG INTC3 IFS2 ST — External Interrupt 2 SDI PAS1 IFS2 ST — SPI data input SDA PAS1 IFS2 ST SEG24 PAS1 — LCD segment output General purpose I/O. Register enabled pull-up and wake-up. NMOS I2C data line LCD 22 LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PA5/INT3/SCK/SCL/ SEG23 PA6/INT0/RX0/SEG22 PA7/INT1/TX0/SEG21 PB0/STCK2/C0X/SEG32 PB1/PTCK3/SEG31 PB2/PTP3I/PTCK2/PTP3/ SEG16 Rev. 1.00 Function OPT I/T O/T PA5 PAWU PAPU PAS1 ST CMOS INT3 PAS1 INTEG INTC3 IFS2 ST — SCK PAS1 IFS2 ST CMOS SPI serial clock SCL PAS1 IFS2 ST NMOS I2C clock line SEG23 PAS1 — LCD PA6 PAWU PAPU PAS1 ST CMOS INT0 PAS1 INTEG INTC0 IFS2 ST — External Interrupt 0 RX0 PAS1 IFS4 ST — UART0 RX serial data input SEG22 PAS1 — LCD PA7 PAWU PAPU PAS1 ST CMOS INT1 PAS1 INTEG INTC0 IFS2 ST — TX0 PAS1 — SEG21 PAS1 — PB0 PBPU PBS0 ST STCK2 PBS0 IFS0 ST Description General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 3 LCD segment output General purpose I/O. Register enabled pull-up and wake-up. LCD segment output General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 1 CMOS UART0 TX serial data output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM2 clock input C0X PBS0 — SEG32 PBS0 — CMOS Comparator 0 output PB1 PBPU PBS0 ST PTCK3 PBS0 IFS0 ST — SEG31 PBS0 — LCD PB2 PBPU PBS0 ST PTP3I PBS0 IFS1 ST — PTM3 capture input PTCK2 PBS0 IFS0 ST — PTM2 clock input PTP3 PBS0 — SEG16 PBS0 — LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTM3 clock input LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS PTM3 output LCD 23 LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PB3/PTP2I/PTP2/SEG27 PB4/C1X/SEG28 PB5/RES/SEG36 PB6/STP1I/STP1/OSC1/ SEG35 PB7/STCK1/OSC2/ SEG34 PC0/VREFI/AN0/SEG52 PC1/C0X/VREF/AN1 PC2/PTP0I/PTP0/AN2/ SEG51 Rev. 1.00 Function OPT I/T PB3 PBPU PBS0 ST PTP2I PBS0 IFS1 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. — PTM2 capture input PTP2 PBS0 — SEG27 PBS0 — PB4 PBPU PBS1 ST CMOS General purpose I/O. Register enabled pull-up. CMOS Comparator 1 output C1X PBS1 — SEG28 PBS1 — PB5 PBPU PBS1 RSTC ST CMOS PTM2 output LCD LCD LCD segment output LCD segment output CMOS General purpose I/O. Register enabled pull-up. RES RSTC ST — External reset input SEG36 PBS1 — LCD LCD segment output PB6 PBPU PBS1 ST STP1I PBS1 IFS1 ST CMOS General purpose I/O. Register enabled pull-up. — STP1 PBS1 — OSC1 PBS1 HXT — SEG35 PBS1 — LCD PB7 PBPU PBS1 ST STCK1 PBS1 IFS0 ST STM1 capture input CMOS STM1 output HXT oscillator pin LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM1 clock input OSC2 PBS1 — HXT HXT oscillator pin SEG34 PBS1 — LCD LCD segment output PC0 PCPU PCS0 ST CMOS General purpose I/O. Register enabled pull-up. VREFI PCS0 AN — A/D Converter reference voltage input AN0 PCS0 AN — A/D Converter analog input SEG52 PCS0 — LCD PC1 PCPU PCS0 ST CMOS General purpose I/O. Register enabled pull-up. CMOS Comparator 0 output LCD segment output C0X PCS0 — VREF PCS0 AN — A/D Converter reference voltage input AN1 PCS0 AN — A/D Converter analog input PC2 PCPU PCS0 ST PTP0I PCS0 IFS1 ST CMOS General purpose I/O. Register enabled pull-up. — PTP0 PCS0 — AN2 PCS0 AN — SEG51 PCS0 — LCD PTM0 capture input CMOS PTM0 output 24 A/D Converter analog input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PC3/PTCK0/PTP4I/ PTP4/AN3/SEG50 PC4/PTP1I/PTP1/AN4/ SEG49 PC5/PTCK1/PTP5I/ PTP5/AN5/SEG48 PC6/STP0I/STP0/AN6/ SEG47 PC7/INT3/STCK0/PTP6I/ PTP6/AN7/SEG46 Rev. 1.00 Function OPT I/T PC3 PCPU PCS0 O/T Description ST PTCK0 PCS0 IFS0 ST — PTM0 clock input PTP4I PCS0 IFS3 ST — PTM4 capture input CMOS General purpose I/O. Register enabled pull-up. PTP4 PCS0 — AN3 PCS0 AN CMOS PTM4 output — SEG50 PCS0 — LCD PC4 PCPU PCS1 ST PTP1I PCS1 IFS1 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM1 capture input PTP1 PCS1 — AN4 PCS1 AN CMOS PTM1 output — SEG49 PCS1 — LCD PC5 PCPU PCS1 ST PTCK1 PCS1 IFS0 ST — PTM1 clock input PTP5I PCS1 IFS3 ST — PTM5 capture input A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTP5 PCS1 — AN5 PCS1 AN CMOS PTM5 output — SEG48 PCS1 — LCD PC6 PCPU PCS1 ST STP0I PCS1 IFS1 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 capture input STP0 PCS1 — AN6 PCS1 AN CMOS STM0 output — SEG47 PCS1 — LCD PC7 PCPU PCS1 ST INT3 PCS1 INTEG INTC3 IFS2 ST — External Interrupt 3 STCK0 PCS1 IFS0 ST — STM0 clock input PTP6I PCS1 IFS3 ST — PTM6 capture input PTP6 PCS1 — AN7 PCS1 AN — SEG46 PCS1 — LCD A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS PTM6 output 25 A/D Converter analog input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PD0/INT2/STP1I/STP1/ AN8/SEG45 PD1/STCK1/RX1/AN9/ SEG44 PD2/PTP2I/PTP2/TX1/ AN10 PD3/PTCK2/PTP7I/ PTP7/AN11/SEG43 PD4/PTP3I/PTP3/RX0/ C1− PD5/PTCK3/TX0/C1+/ SEG38 Rev. 1.00 Function OPT I/T PD0 PDPU PDS0 O/T Description ST INT2 PDS0 INTEG INTC3 IFS2 ST — External Interrupt 2 STP1I PDS0 IFS1 ST — STM1 capture input CMOS General purpose I/O. Register enabled pull-up. STP1 PDS0 — AN8 PDS0 AN CMOS STM1 output — SEG45 PCS1 — LCD PD1 PDPU PDS0 ST STCK1 PDS0 IFS0 ST — STM1 clock input RX1 PDS0 IFS4 ST — UART1 RX serial data input A/D Converter analog input A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. AN9 PDS0 AN — SEG44 PDS0 — LCD PD2 PDPU PDS0 ST PTP2I PDS0 IFS1 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM2 capture input PTP2 PDS0 — CMOS PTM2 output TX1 PDS0 — CMOS UART1 TX serial data output AN10 PDS0 AN PD3 PDPU PDS0 ST PTCK2 PDS0 IFS0 ST — PTM2 clock input PTP7I PDS0 IFS3 ST — PTM7 capture input — A/D Converter analog input CMOS General purpose I/O. Register enabled pull-up. PTP7 PDS0 — AN11 PDS0 AN CMOS PTM7 output — SEG43 PDS0 — LCD PD4 PDPU PDS1 ST PTP3I PDS1 IFS1 ST PTP3 PDS1 — RX0 PDS1 IFS4 ST — UART0 RX serial data input C1− PDS1 AN — Comparator 1 negative input PD5 PDPU PDS1 ST PTCK3 PDS1 IFS0 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM3 capture input CMOS PTM3 output CMOS General purpose I/O. Register enabled pull-up. — TX0 PDS1 — C1+ PDS1 AN — SEG38 PDS1 — LCD PTM3 clock input CMOS UART0 TX serial data output 26 Comparator 1 positive input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PD6/STP2I/STP2/C1X/ SEG33 PE0/STCK0/SCSA/SEG7 PE1/STP0I/STP0/SDOA/ SEG6 PE2/PTCK1/SDIA/SEG5 PE3/PTP1I/PTP1/SCKA/ SEG4 PE4 PE5/C2/SEG55 PE6/C1/SEG54 PE7/V2/SEG53 PF0/SCS/SEG15 Rev. 1.00 Function OPT I/T PD6 PDPU PDS1 ST STP2I PDS1 IFS1 ST STP2 PDS1 — CMOS STM2 output C1X PDS1 — CMOS Comparator 1 output SEG33 PDS1 — PE0 PEPU PES0 ST STCK0 PES0 IFS0 ST SCSA PES0 ST SEG7 PES0 — PE1 PEPU PES0 ST STP0I PES0 IFS1 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. — LCD STM2 capture input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 clock input CMOS SPIA slave select LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 capture input STP0 PES0 — CMOS STM0 inverted output SDOA PES0 — CMOS SPIA data output SEG6 PES0 — PE2 PEPU PES0 ST PTCK1 PES0 IFS0 ST LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM1 clock input SPIA data input SDIA PES0 ST — SEG5 PES0 — LCD PE3 PEPU PES0 ST PTP1I PES0 IFS1 ST PTP1 PES0 — CMOS PTM1 output SCKA PES0 ST CMOS SPIA serial clock SEG4 PES0 — PE4 PEPU PES1 ST CMOS General purpose I/O. Register enabled pull-up. PE5 PEPU PES1 ST CMOS General purpose I/O. Register enabled pull-up. C2 PES1 — AN SEG55 PES1 — LCD PE6 PEPU PES1 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — LCD PTM1 capture input LCD segment output LCD voltage pump LCD segment output CMOS General purpose I/O. Register enabled pull-up. C1 PES1 — AN SEG54 PES1 — LCD PE7 PEPU PES1 ST LCD voltage pump LCD segment output CMOS General purpose I/O. Register enabled pull-up. V2 PES1 PWR AN SEG53 PES1 — LCD PF0 PFPU PFS0 ST CMOS General purpose I/O. Register enabled pull-up. SCS PFS0 IFS2 ST CMOS SPI slave select SEG15 PFS0 — LCD 27 LCD voltage pump LCD segment output LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PF1/SDO/SEG14 PF2/SDI/SDA/SEG13 PF3/SCK/SCL/SEG12 PF4/PTCK0/XT2 PF5/PTP0I/PTP0/XT1 PF6/STCK2/RX1/C0−/ SEG37 PF7/STP2I/STP2/TX1/ C0+ PG0/COM0 PG1/COM1 Rev. 1.00 Function OPT I/T PF1 PFPU PFS0 O/T Description ST CMOS General purpose I/O. Register enabled pull-up. CMOS SPI data output SDO PFS0 — SEG14 PFS0 — PF2 PFPU PFS0 ST SDI PFS0 IFS2 ST SDA PFS0 IFS2 ST SEG13 PFS0 — PF3 PFPU PFS0 ST CMOS General purpose I/O. Register enabled pull-up. SCK PFS0 IFS2 ST CMOS SPI serial clock SCL PFS0 IFS2 ST NMOS I2C clock line SEG12 PFS0 — PF4 PFPU PFS1 ST PTCK0 PFS1 IFS0 ST — PTM0 clock input XT2 PFS1 — LXT LXT oscillator pin PF5 PFPU PFS1 ST PTP0I PFS1 IFS1 ST LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — SPI data input NMOS I2C data line LCD LCD LCD segment output LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS General purpose I/O. Register enabled pull-up. — PTM0 capture input PTP0 PFS1 — XT1 PFS1 LXT CMOS PTM0 output PF6 PFPU PFS1 ST STCK2 PFS1 IFS0 ST — STM2 clock input RX1 PFS1 IFS4 ST — UART1 RX serial data input Comparator 0 negative input — LXT oscillator pin CMOS General purpose I/O. Register enabled pull-up. C0− PFS1 AN — SEG37 PFS1 — LCD PF7 PFPU PFS1 ST STP2I PFS1 IFS1 ST STP2 PFS1 — CMOS STM2 output TX1 PFS1 — CMOS UART1 TX serial data output C0+ PFS1 AN PG0 PGPU PGS0 ST COM0 PGS0 — PG1 PGPU PGS0 ST COM1 PGS0 — LCD segment output CMOS General purpose I/O. Register enabled pull-up. — — STM2 capture input Comparator 0 positive input CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD 28 LCD common output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PG2/COM2 PG3/COM3 PG4/COM0 PG5/COM1 PG6/COM2 PG7/COM3 PH0/PTP4I/PTP4/SEG20 PH1/PTP5I/PTP5/SEG19 PH2/PTCK4/AN12/ SEG42 PH3/PTCK5/AN13/ SEG41 PH4/PTCK6/AN14/ SEG40 Rev. 1.00 Function OPT I/T PG2 PGPU PGS0 ST COM2 PGS0 — PG3 PGPU PGS0 ST COM3 PGS0 — PG4 PGPU PGS1 ST COM0 PGS1 — PG5 PGPU PGS1 ST COM1 PGS1 — PG6 PGPU PGS1 ST COM2 PGS1 — PG7 PGPU PGS1 ST COM3 PGS1 — PH0 PHPU PHS0 ST PTP4I PHS0 IFS3 ST PTP4 PHS0 — SEG20 PHS0 — PH1 PHPU PHS0 ST PTP5I PHS0 IFS3 ST PTP5 PHS0 — SEG19 PHS0 — PH2 PHPU PHS0 ST PTCK4 PHS0 IFS3 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. — PTM4 capture input CMOS PTM4 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM5 capture input CMOS PTM5 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM4 clock input A/D Converter analog input AN12 PHS0 AN — SEG42 PHS0 — LCD PH3 PHPU PHS0 ST PTCK5 PHS0 IFS3 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM5 clock input A/D Converter analog input AN13 PHS0 AN — SEG41 PHS0 — LCD PH4 PHPU PHS1 ST PTCK6 PHS1 IFS3 ST AN14 PHS1 SEG40 PHS1 LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM6 clock input AN — A/D Converter analog input — LCD 29 LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PH5/PTCK7/AN15/ SEG39 PH6/PTP6I/PTP6/SEG18 PH7/PTP7I/PTP7/SEG17 PJ0/COM4/SEG0 PJ1/COM5/SEG1 PJ2/COM6/SEG2 PJ3/COM7/SEG3 PJ4/PTCK7/SEG8 PJ5/PTCK6/SEG9 PJ6/PTCK5/SEG10 Rev. 1.00 Function OPT I/T PH5 PHPU PHS1 ST PTCK7 PHS1 IFS3 ST O/T CMOS General purpose I/O. Register enabled pull-up. — PTM7 clock input A/D Converter analog input AN15 PHS1 AN — SEG39 PHS1 — LCD PH6 PHPU PHS1 ST PTP6I PHS1 IFS3 ST PTP6 PHS1 — SEG18 PHS1 — PH7 PHPU PHS1 ST PTP7I PHS1 IFS3 ST PTP7 PHS1 — SEG17 PHS1 — PJ0 PJPU PJS0 ST Description LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM6 capture input CMOS PTM6 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM7 capture input CMOS PTM7 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. COM4 PJS0 — LCD LCD common output SEG0 PJS0 — LCD LCD segment output PJ1 PJPU PJS0 ST CMOS General purpose I/O. Register enabled pull-up. COM5 PJS0 — LCD LCD common output SEG1 PJS0 — LCD LCD segment output PJ2 PJPU PJS0 ST COM6 PJS0 — LCD LCD common output SEG2 PJS0 — LCD LCD segment output PJ3 PJPU PJS0 ST CMOS General purpose I/O. Register enabled pull-up. CMOS General purpose I/O. Register enabled pull-up. COM7 PJS0 — LCD LCD common output SEG3 PJS0 — LCD LCD segment output PJ4 PJPU PJS1 ST PTCK7 PJS1 IFS3 ST — SEG8 PJS1 — LCD PJ5 PJPU PJS1 ST PTCK6 PJS1 IFS3 ST — SEG9 PJS1 — LCD PJ6 PJPU PJS1 ST PTCK5 PJS1 IFS3 ST — SEG10 PJS1 — LCD CMOS General purpose I/O. Register enabled pull-up. PTM5 clock input LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTM4 clock input LCD segment output CMOS General purpose I/O. Register enabled pull-up. 30 PTM5 clock input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PJ7/PTCK4/SEG11 VDD VSS Function OPT I/T PJ7 PJPU PJS1 O/T Description ST PTCK4 PJS1 IFS3 ST — SEG11 PJS1 — LCD LCD segment output VDD — PWR — Positive power supply CMOS General purpose I/O. Register enabled pull-up. PTM4 clock input VSS — PWR — Negative power supply, ground. AVDD AVDD — PWR — Analog positive power supply AVSS AVSS — PWR — Analog negative power supply, ground. VMAX VMAX — PWR — IC maximum voltage, connected to VDD or V1. V1 — PWR AN LCD voltage pump PLCD — PWR AN LCD power supply V1 PLCD Legend: I/T: Input type; CMOS: CMOS output; ST: Schmitt Trigger input; HXT: High frequency crystal oscillator; LCD: LCD SEG/COM output; O/T: Output type; OPT: Optional by register option; NMOS: NMOS output; AN: Analog signal; LXT: Low frequency crystal oscillator; PWR: Power HT67F2370/HT67F2390 Pad Name PA0/SEG30/ICPDA/ OCDSDA PA1/INT0/SCS/SEG26 PA2/SEG29/ICPCK/ OCDSCK PA3/INT1/SDO/SEG25 Rev. 1.00 Function OPT I/T O/T PA0 PAWU PAPU PAS0 ST CMOS SEG30 PAS0 — ICPDA — ST CMOS ICP Data/Address pin OCDSDA — ST CMOS OCDS Data/Address pin, for EV chip only. PA1 PAWU PAPU PAS0 ST CMOS INT0 PAS0 INTEG INTC0 IFS2 ST — SCS PAS0 IFS2 ST SEG26 PAS0 — LCD PA2 PAWU PAPU PAS0 ST CMOS SEG29 PAS0 — ICPCK — ST OCDSCK — ST — PA3 PAWU PAPU PAS0 ST CMOS INT1 PAS0 INTEG INTC0 IFS2 ST — SDO PAS0 — SEG25 PAS0 — LCD Description General purpose I/O. Register enabled pull-up and wake-up. LCD segment output General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 0 CMOS SPI slave select LCD LCD segment output General purpose I/O. Register enabled pull-up and wake-up. LCD segment output CMOS ICP Clock pin OCDS Clock pin, for EV chip only. General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 1 CMOS SPI data output LCD 31 LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PA4/INT2/SDI/SDA/ SEG24 PA5/INT3/SCK/SCL/ SEG23 PA6/INT0/RX0/SEG22 PA7/INT1/TX0/SEG21 PB0/STCK2/RX2/C0X/ SEG32 Rev. 1.00 Function OPT I/T O/T PA4 PAWU PAPU PAS1 Description ST CMOS INT2 PAS1 INTEG INTC3 IFS2 ST — External Interrupt 2 SDI PAS1 IFS2 ST — SPI data input SDA PAS1 IFS2 ST SEG24 PAS1 — LCD PA5 PAWU PAPU PAS1 ST CMOS INT3 PAS1 INTEG INTC3 IFS2 ST — SCK PAS1 IFS2 ST CMOS SPI serial clock SCL PAS1 IFS2 ST NMOS I2C clock line SEG23 PAS1 — LCD PA6 PAWU PAPU PAS1 ST CMOS INT0 PAS1 INTEG INTC0 IFS2 ST — External Interrupt 0 RX0 PAS1 IFS4 ST — UART0 RX serial data input SEG22 PAS1 — LCD PA7 PAWU PAPU PAS1 ST CMOS INT1 PAS1 INTEG INTC0 IFS2 ST — TX0 PAS1 — SEG21 PAS1 — PB0 PBPU PBS0 ST STCK2 PBS0 IFS0 ST — STM2 clock input RX2 PBS0 IFS4 ST — UART2 RX serial data input C0X PBS0 — SEG32 PBS0 — General purpose I/O. Register enabled pull-up and wake-up. NMOS I2C data line LCD segment output General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 3 LCD segment output General purpose I/O. Register enabled pull-up and wake-up. LCD segment output General purpose I/O. Register enabled pull-up and wake-up. External Interrupt 1 CMOS UART0 TX serial data output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS Comparator 0 output LCD 32 LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PB1/PTCK3/TX2/SEG31 PB2/PTP3I/PTCK2/ PTP3/SEG16 PB3/PTP2I/PTP2/SEG27 PB4/C1X/SEG28 PB5/RES/SEG36 PB6/STP1I/STP1/OSC1/ SEG35 PB7/STCK1/OSC2/ SEG34 PC0/VREFI/AN0/SEG52 PC1/C0X/VREF/AN1 Rev. 1.00 Function OPT I/T PB1 PBPU PBS0 ST PTCK3 PBS0 IFS0 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. — PTM3 clock input TX2 PBS0 — SEG31 PBS0 — CMOS UART2 TX serial data output PB2 PBPU PBS0 ST PTP3I PBS0 IFS1 ST — PTM3 capture input PTCK2 PBS0 IFS0 ST — PTM2 clock input LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTP3 PBS0 — SEG16 PBS0 — PB3 PBPU PBS0 ST PTP2I PBS0 IFS1 ST PTP2 PBS0 — SEG27 PBS0 — PB4 PBPU PBS1 ST CMOS General purpose I/O. Register enabled pull-up. CMOS Comparator 1 output C1X PBS1 — SEG28 PBS1 — PB5 PBPU PBS1 RSTC ST CMOS PTM3 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM2 capture input CMOS PTM2 output LCD LCD LCD segment output LCD segment output CMOS General purpose I/O. Register enabled pull-up. RES RSTC ST — External reset input SEG36 PBS1 — LCD LCD segment output PB6 PBPU PBS1 ST STP1I PBS1 IFS1 ST CMOS General purpose I/O. Register enabled pull-up. — STP1 PBS1 — OSC1 PBS1 HXT — SEG35 PBS1 — LCD PB7 PBPU PBS1 ST STCK1 PBS1 IFS0 ST STM1 capture input CMOS STM1 output HXT oscillator pin LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM1 clock input OSC2 PBS1 — HXT HXT oscillator pin SEG34 PBS1 — LCD LCD segment output PC0 PCPU PCS0 ST CMOS General purpose I/O. Register enabled pull-up. VREFI PCS0 AN — A/D Converter reference voltage input AN0 PCS0 AN — A/D Converter analog input SEG52 PCS0 — LCD PC1 PCPU PCS0 ST CMOS General purpose I/O. Register enabled pull-up. CMOS Comparator 0 output LCD segment output C0X PCS0 — VREF PCS0 AN — A/D Converter reference voltage input AN1 PCS0 AN — A/D Converter analog input 33 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PC2/PTP0I/PTP0/AN2/ SEG51 PC3/PTCK0/PTP4I/ PTP4/AN3/SEG50 PC4/PTP1I/PTP1/AN4/ SEG49 PC5/PTCK1/PTP5I/ PTP5/AN5/SEG48 PC6/STP0I/STP0/AN6/ SEG47 PC7/INT3/STCK0/PTP6I/ PTP6/AN7/SEG46 Rev. 1.00 Function OPT I/T PC2 PCPU PCS0 ST PTP0I PCS0 IFS1 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. — PTM0 capture input PTP0 PCS0 — AN2 PCS0 AN CMOS PTM0 output — SEG51 PCS0 — LCD PC3 PCPU PCS0 ST PTCK0 PCS0 IFS0 ST — PTM0 clock input PTP4I PCS0 IFS3 ST — PTM4 capture input A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTP4 PCS0 — AN3 PCS0 AN CMOS PTM4 output — SEG50 PCS0 — LCD PC4 PCPU PCS1 ST PTP1I PCS1 IFS1 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM1 capture input PTP1 PCS1 — AN4 PCS1 AN CMOS PTM1 output — SEG49 PCS1 — LCD PC5 PCPU PCS1 ST PTCK1 PCS1 IFS0 ST — PTM1 clock input PTP5I PCS1 IFS3 ST — PTM5 capture input A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTP5 PCS1 — AN5 PCS1 AN CMOS PTM5 output — SEG48 PCS1 — LCD PC6 PCPU PCS1 ST STP0I PCS1 IFS1 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 capture input STP0 PCS1 — AN6 PCS1 AN CMOS STM0 output — SEG47 PCS1 — LCD PC7 PCPU PCS1 ST INT3 PCS1 INTEG INTC3 IFS2 ST — External Interrupt 3 STCK0 PCS1 IFS0 ST — STM0 clock input PTP6I PCS1 IFS3 ST — PTM6 capture input PTP6 PCS1 — AN7 PCS1 AN — SEG46 PCS1 — LCD A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS PTM6 output 34 A/D Converter analog input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PD0/INT2/STP1I/STP1/ AN8/SEG45 PD1/STCK1/RX1/AN9/ SEG44 PD2/PTP2I/PTP2/TX1/ AN10 PD3/PTCK2/PTP7I/ PTP7/AN11/SEG43 PD4/PTP3I/PTP3/RX0/ C1− PD5/PTCK3/TX0/C1+/ SEG38 Rev. 1.00 Function OPT I/T PD0 PDPU PDS0 O/T Description ST INT2 PDS0 INTEG INTC3 IFS2 ST — External Interrupt 2 STP1I PDS0 IFS1 ST — STM1 capture input CMOS General purpose I/O. Register enabled pull-up. STP1 PDS0 — AN8 PDS0 AN CMOS STM1 output — SEG45 PCS1 — LCD PD1 PDPU PDS0 ST STCK1 PDS0 IFS0 ST — STM1 clock input RX1 PDS0 IFS4 ST — UART1 RX serial data input A/D Converter analog input A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. AN9 PDS0 AN — SEG44 PDS0 — LCD PD2 PDPU PDS0 ST PTP2I PDS0 IFS1 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM2 capture input PTP2 PDS0 — CMOS PTM2 output TX1 PDS0 — CMOS UART1 TX serial data output AN10 PDS0 AN PD3 PDPU PDS0 ST PTCK2 PDS0 IFS0 ST — PTM2 clock input PTP7I PDS0 IFS3 ST — PTM7 capture input — A/D Converter analog input CMOS General purpose I/O. Register enabled pull-up. PTP7 PDS0 — AN11 PDS0 AN CMOS PTM7 output — SEG43 PDS0 — LCD PD4 PDPU PDS1 ST PTP3I PDS1 IFS1 ST PTP3 PDS1 — RX0 PDS1 IFS4 ST — UART0 RX serial data input C1− PDS1 AN — Comparator 1 negative input PD5 PDPU PDS1 ST PTCK3 PDS1 IFS0 ST A/D Converter analog input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM3 capture input CMOS PTM3 output CMOS General purpose I/O. Register enabled pull-up. — TX0 PDS1 — C1+ PDS1 AN — SEG38 PDS1 — LCD PTM3 clock input CMOS UART0 TX serial data output 35 Comparator 1 positive input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PD6/STP2I/STP2/C1X/ SEG33 PE0/STCK0/SCSA/SEG7 PE1/STP0I/STP0/SDOA/ SEG6 PE2/PTCK1/SDIA/SEG5 PE3/PTP1I/PTP1/SCKA/ SEG4 PE4 PE5/C2/SEG55 PE6/C1/SEG54 PE7/V2/SEG53 PF0/SCS/SEG15 Rev. 1.00 Function OPT I/T PD6 PDPU PDS1 ST STP2I PDS1 IFS1 ST STP2 PDS1 — CMOS STM2 output C1X PDS1 — CMOS Comparator 1 output SEG33 PDS1 — PE0 PEPU PES0 ST STCK0 PES0 IFS0 ST SCSA PES0 ST SEG7 PES0 — PE1 PEPU PES0 ST STP0I PES0 IFS1 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. — LCD STM2 capture input LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 clock input CMOS SPIA slave select LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — STM0 capture input STP0 PES0 — CMOS STM0 inverted output SDOA PES0 — CMOS SPIA data output SEG6 PES0 — PE2 PEPU PES0 ST PTCK1 PES0 IFS0 ST LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM1 clock input SPIA data input SDIA PES0 ST — SEG5 PES0 — LCD PE3 PEPU PES0 ST PTP1I PES0 IFS1 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM1 capture input PTP1 PES0 — CMOS PTM1 output SCKA PES0 ST CMOS SPIA serial clock SEG4 PES0 — PE4 PEPU PES1 ST CMOS General purpose I/O. Register enabled pull-up. PE5 PEPU PES1 ST CMOS General purpose I/O. Register enabled pull-up. C2 PES1 — AN SEG55 PES1 — LCD PE6 PEPU PES1 ST LCD LCD segment output LCD voltage pump LCD segment output CMOS General purpose I/O. Register enabled pull-up. C1 PES1 — AN SEG54 PES1 — LCD PE7 PEPU PES1 ST LCD voltage pump LCD segment output CMOS General purpose I/O. Register enabled pull-up. V2 PES1 PWR AN SEG53 PES1 — LCD PF0 PFPU PFS0 ST CMOS General purpose I/O. Register enabled pull-up. SCS PFS0 IFS2 ST CMOS SPI slave select SEG15 PFS0 — LCD 36 LCD voltage pump LCD segment output LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PF1/SDO/SEG14 PF2/SDI/SDA/SEG13 PF3/SCK/SCL/SEG12 PF4/PTCK0/XT2 PF5/PTP0I/PTP0/XT1 PF6/STCK2/RX1/C0−/ SEG37 PF7/STP2I/STP2/TX1/ C0+ PG0/COM0 PG1/COM1 Rev. 1.00 Function OPT I/T PF1 PFPU PFS0 O/T Description ST CMOS General purpose I/O. Register enabled pull-up. CMOS SPI data output SDO PFS0 — SEG14 PFS0 — PF2 PFPU PFS0 ST SDI PFS0 IFS2 ST SDA PFS0 IFS2 ST SEG13 PFS0 — PF3 PFPU PFS0 ST CMOS General purpose I/O. Register enabled pull-up. SCK PFS0 IFS2 ST CMOS SPI serial clock SCL PFS0 IFS2 ST NMOS I2C clock line SEG12 PFS0 — PF4 PFPU PFS1 ST PTCK0 PFS1 IFS0 ST — PTM0 clock input XT2 PFS1 — LXT LXT oscillator pin PF5 PFPU PFS1 ST PTP0I PFS1 IFS1 ST PTP0 PFS1 — XT1 PFS1 LXT PF6 PFPU PFS1 ST STCK2 PFS1 IFS0 ST — STM2 clock input RX1 PFS1 IFS4 ST — UART1 RX serial data input Comparator 0 negative input LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — SPI data input NMOS I2C data line LCD LCD LCD segment output LCD segment output CMOS General purpose I/O. Register enabled pull-up. CMOS General purpose I/O. Register enabled pull-up. — PTM0 capture input CMOS PTM0 output — LXT oscillator pin CMOS General purpose I/O. Register enabled pull-up. C0− PFS1 AN — SEG37 PFS1 — LCD PF7 PFPU PFS1 ST STP2I PFS1 IFS1 ST STP2 PFS1 — CMOS STM2 output TX1 PFS1 — CMOS UART1 TX serial data output C0+ PFS1 AN PG0 PGPU PGS0 ST COM0 PGS0 — PG1 PGPU PGS0 ST COM1 PGS0 — LCD segment output CMOS General purpose I/O. Register enabled pull-up. — — STM2 capture input Comparator 0 positive input CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD 37 LCD common output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PG2/COM2 PG3/COM3 PG4/COM0 PG5/COM1 PG6/COM2 PG7/COM3 PH0/PTP4I/PTP4/SEG20 PH1/PTP5I/PTP5/SEG19 PH2/PTCK4/AN12/ SEG42 PH3/PTCK5/AN13/ SEG41 PH4/PTCK6/AN14/ SEG40 Rev. 1.00 Function OPT I/T PG2 PGPU PGS0 ST COM2 PGS0 — PG3 PGPU PGS0 ST COM3 PGS0 — PG4 PGPU PGS1 ST COM0 PGS1 — PG5 PGPU PGS1 ST COM1 PGS1 — PG6 PGPU PGS1 ST COM2 PGS1 — PG7 PGPU PGS1 ST COM3 PGS1 — PH0 PHPU PHS0 ST PTP4I PHS0 IFS3 ST PTP4 PHS0 — SEG20 PHS0 — PH1 PHPU PHS0 ST PTP5I PHS0 IFS3 ST PTP5 PHS0 — SEG19 PHS0 — PH2 PHPU PHS0 ST PTCK4 PHS0 IFS3 ST O/T Description CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. LCD LCD common output CMOS General purpose I/O. Register enabled pull-up. — PTM4 capture input CMOS PTM4 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM5 capture input CMOS PTM5 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM4 clock input A/D Converter analog input AN12 PHS0 AN — SEG42 PHS0 — LCD PH3 PHPU PHS0 ST PTCK5 PHS0 IFS3 ST LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM5 clock input A/D Converter analog input AN13 PHS0 AN — SEG41 PHS0 — LCD PH4 PHPU PHS1 ST PTCK6 PHS1 IFS3 ST AN14 PHS1 SEG40 PHS1 LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM6 clock input AN — A/D Converter analog input — LCD 38 LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PH5/PTCK7/AN15/ SEG39 PH6/PTP6I/PTP6/SEG18 PH7/PTP7I/PTP7/SEG17 PJ0/COM4/SEG0 PJ1/COM5/SEG1 PJ2/COM6/SEG2 PJ3/COM7/SEG3 PJ4/PTCK7/SEG8 PJ5/PTCK6/SEG9 PJ6/PTCK5/SEG10 Rev. 1.00 Function OPT I/T PH5 PHPU PHS1 ST PTCK7 PHS1 IFS3 ST O/T CMOS General purpose I/O. Register enabled pull-up. — PTM7 clock input A/D Converter analog input AN15 PHS1 AN — SEG39 PHS1 — LCD PH6 PHPU PHS1 ST PTP6I PHS1 IFS3 ST PTP6 PHS1 — SEG18 PHS1 — PH7 PHPU PHS1 ST PTP7I PHS1 IFS3 ST PTP7 PHS1 — SEG17 PHS1 — PJ0 PJPU PJS0 ST Description LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM6 capture input CMOS PTM6 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. — PTM7 capture input CMOS PTM7 output LCD LCD segment output CMOS General purpose I/O. Register enabled pull-up. COM4 PJS0 — LCD LCD common output SEG0 PJS0 — LCD LCD segment output PJ1 PJPU PJS0 ST CMOS General purpose I/O. Register enabled pull-up. COM5 PJS0 — LCD LCD common output SEG1 PJS0 — LCD LCD segment output PJ2 PJPU PJS0 ST COM6 PJS0 — LCD LCD common output SEG2 PJS0 — LCD LCD segment output PJ3 PJPU PJS0 ST CMOS General purpose I/O. Register enabled pull-up. CMOS General purpose I/O. Register enabled pull-up. COM7 PJS0 — LCD LCD common output SEG3 PJS0 — LCD LCD segment output PJ4 PJPU PJS1 ST PTCK7 PJS1 IFS3 ST — SEG8 PJS1 — LCD PJ5 PJPU PJS1 ST PTCK6 PJS1 IFS3 ST — SEG9 PJS1 — LCD PJ6 PJPU PJS1 ST PTCK5 PJS1 IFS3 ST — SEG10 PJS1 — LCD CMOS General purpose I/O. Register enabled pull-up. PTM5 clock input LCD segment output CMOS General purpose I/O. Register enabled pull-up. PTM4 clock input LCD segment output CMOS General purpose I/O. Register enabled pull-up. 39 PTM5 clock input LCD segment output December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pad Name PJ7/PTCK4/SEG11 VDD VSS Function OPT I/T PJ7 PJPU PJS1 O/T Description ST PTCK4 PJS1 IFS3 ST — SEG11 PJS1 — LCD LCD segment output VDD — PWR — Positive power supply CMOS General purpose I/O. Register enabled pull-up. PTM4 clock input VSS — PWR — Negative power supply, ground. AVDD AVDD — PWR — Analog positive power supply AVSS AVSS — PWR — Analog negative power supply, ground. VMAX VMAX — PWR — IC maximum voltage, connected to VDD or V1. V1 — PWR AN LCD voltage pump PLCD — PWR AN LCD power supply V1 PLCD Legend: I/T: Input type; CMOS: CMOS output; ST: Schmitt Trigger input; HXT: High frequency crystal oscillator; LCD: LCD SEG/COM output; O/T: Output type; OPT: Optional by register option; NMOS: NMOS output; AN: Analog signal; LXT: Low frequency crystal oscillator; PWR: Power Absolute Maximum Ratings Supply Voltage.................................................................................................VSS−0.3V to VSS+6.0V Input Voltage...................................................................................................VSS−0.3V to VDD+0.3V Storage Temperature.....................................................................................................-50˚C to 125˚C Operating Temperature...................................................................................................-40˚C to 85˚C IOL Total...................................................................................................................................... 80mA IOH Total.....................................................................................................................................-80mA Total Power Dissipation.......................................................................................................... 500mW Note: These are stress ratings only. Stresses exceeding the range specified under "Absolute Maximum Ratings" may cause substantial damage to these devices. Functional operation of these devices at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect devices reliability. D.C. Characteristics For data in the following tables, note that factors such as oscillator type, operating voltage, operating frequency, pin load conditions, temperature and program instruction type, etc., can all exert an influence on the measured values. Operating Voltage Characteristics Ta= -40°C to 85°C Symbol Parameter Min. Typ. Max. fSYS=8MHz 2.2 — 5.5 fSYS=12MHz 2.7 — 5.5 fSYS=16MHz 3.3 — 5.5 fSYS=8MHz 2.2 — 5.5 fSYS=12MHz 2.7 — 5.5 fSYS=16MHz 3.3 — 5.5 Operating Voltage – LXT fSYS=32768Hz 2.2 — 5.5 V Operating Voltage – LIRC fSYS=32kHz 2.2 — 5.5 V Operating Voltage – HXT VDD Rev. 1.00 Operating Voltage – HIRC Test Conditions 40 Unit V V December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Standby Current Characteristics Ta=25°C Symbol Standby Mode Test Conditions Min. Typ. Max. — 0.2 0.6 — 0.2 0.8 1 — 0.5 1 1.2 — 1.2 2.4 2.9 — — 3 3.6 5V — — 5 6 2.2V — 2.4 4 4.8 VDD Conditions 2.2V 3V SLEEP Mode WDT off 5V 2.2V 3V IDLE0 Mode 3V WDT on fSUB on 5V 2.2V 3V fSUB on, fSYS=8MHz 5V ISTB IDLE1 Mode – HIRC 2.7V 3V fSUB on, fSYS=12MHz 85°C — 3 5 6 — 5 10 12 — 0.3 0.6 0.8 — 0.5 1.0 1.2 — 1.0 2.0 2.2 — 0.4 0.8 1.0 — 0.6 1.2 1.4 5V — 1.2 2.4 2.6 — 1.5 3.0 3.2 — 2.0 4.0 4.2 — 0.3 0.6 0.8 — 0.5 1.0 1.2 — 1.0 2.0 2.2 — 0.4 0.8 1.0 — 0.6 1.2 1.4 fSUB on, fSYS=16MHz 2.2V 3V fSUB on, fSYS=8MHz 5V 2.7V 3V fSUB on, fSYS=12MHz 5V — 1.2 2.4 2.6 3.3V — 1.5 3.0 3.2 — 2.0 4.0 4.2 5V fSUB on, fSYS=16MHz Unit 0.7 3.3V 5V IDLE1 Mode – HXT Max. μA μA μA mA mA mA mA mA mA Notes: When using the characteristic table data, the following notes should be taken into consideration: • Any digital inputs are setup in a non floating condition. • All measurements are taken under conditions of no load and with all peripherals in an off state. • There are no DC current paths. • All Standby Current values are taken after a HALT instruction execution thus stopping all instruction execution. Rev. 1.00 41 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Operating Current Characteristics Ta=25°C Symbol Test Conditions Operating Mode VDD Conditions 2.2V SLOW Mode – LXT 3V fSYS=32768Hz 5V 2.2V Max. 16 — 8 — 10 20 — 30 50 16 — 8 10 20 5V — 30 50 2.2V — 0.8 1.2 — 1 1.5 — 2 3 3V fSYS=32kHz fSYS=8MHz 5V 2.7V 3V IDD fSYS=12MHz 5V 3.3V 5V fSYS=16MHz 2.2V 3V fSYS=8MHz 5V FAST Mode – HXT Typ. — 3V SLOW Mode – LIRC FAST Mode – HIRC Min. 2.7V 3V fSYS=12MHz 5V 3.3V 5V fSYS=16MHz — 1.2 2.2 — 1.5 2.75 — 3 4.5 — 3.2 4.8 — 4.5 7.0 — 0.8 1.2 — 1 1.5 — 2 3 — 1.2 2.2 — 1.5 2.75 — 3 4.5 — 3.2 4.8 — 4.5 7.0 Unit μA μA mA mA mA mA mA mA Notes: When using the characteristic table data, the following notes should be taken into consideration: • Any digital inputs are setup in a non floating condition. • All measurements are taken under conditions of no load and with all peripherals in an off state. • There are no DC current paths. • All Operating Current values are measured using a continuous NOP instruction program loop. Rev. 1.00 42 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM A.C. Characteristics For data in the following tables, note that factors such as oscillator type, operating voltage, operating frequency and temperature etc., can all exert an influence on the measured values. High Speed Internal Oscillator – HIRC – Frequency Accuracy During the program writing operation the writer will trim the HIRC oscillator at a user selected HIRC frequency and user selected voltage of either 3V or 5V. 8/12/16 MHz Symbol Parameter 8 MHz Writer Trimmed HIRC Frequency 12 MHz Writer Trimmed HIRC Frequency fHIRC 16 MHz Writer Trimmed HIRC Frequency Test Conditions Min Typ Ta=25°C -1% 8 +1% Ta= -40°C ~ 85°C -2% 8 +2% -2.5% 8 +2.5% Temp. VDD 3V/5V Ta=25°C 2.2V~5.5V 3V/5V Ta= -40°C ~ 85°C -3% 8 +3% Ta=25°C -1% 12 +1% -2% 12 +2% -2.5% 12 +2.5% Ta= -40°C ~ 85°C -3% 12 +3% Ta=25°C -1% 16 +1% Ta= -40°C ~ 85°C -2% 16 +2% -2.5% 16 +2.5% -3% 16 +3% Ta= -40°C ~ 85°C Ta=25°C 2.7V~5.5V 5V Ta=25°C 3.3V~5.5V Max Ta= -40°C ~ 85°C Unit MHz MHz MHz Notes: 1. The 3V/5V values for VDD are provided as these are the two selectable fixed voltages at which the HIRC frequency is trimmed by the writer. 2. The row below the 3V/5V trim voltage row is provided to show the values for the full VDD range operating voltage. It is recommended that the trim voltage is fixed at 3V for application voltage ranges from 2.2V to 3.3V and fixed at 5V for application voltage ranges from 3.3V to 5.5V. 3. The minimum and maximum tolerance values provided in the table are only for the frequency at which the writer trims the HIRC oscillator. After trimming at this chosen specific frequency any change in HIRC oscillator frequency using the oscillator register control bits by the application program will give a frequency tolerance to within ±20%. Low Speed Internal Oscillator Characteristics – LIRC Ta=25°C, unless otherwise specified Symbol Parameter fLIRC Oscillator Frequency tSTART Start Up Time Test Conditions Min. Typ. Ta=25°C -5% 32 +5% Ta= -40°C ~ 85°C -10% 32 +10% — — 100 Temp. VDD 2.2V~5.5V — — Max. Unit kHz μs Low Speed Crystal Oscillator Characteristics – LXT Ta=25°C, unless otherwise specified Symbol Parameter Test Conditions VDD Conditions Min. Typ. Max. Unit -10% 32.768 +10% kHz fLXT Oscillator Frequency Duty Cycle Duty Cycle — — 45 50 55 % tSTART Start Up Time — — — — 500 ms RNEG Negative Resistance * 2.2V — 3*ESR — — Ω 2.2~5.5V Ta= -40°C ~ 85°C Note: *: C1, C2 and RP are external components. C1=C2=10pF. RP=10MΩ. CL=7pF, ESR=30kΩ. Rev. 1.00 43 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Operating Frequency Characteristic Curves System Operating Frequency 16MHz 12MHz 8MHz ~ ~ ~ ~ ~ ~ 2.2V 2.7V 3.3V 5.5V Operating Voltage System Start Up Time Characteristics Ta= -40°C ~ 85°C Symbol Parameter System Start-up Time Wake-up from Condition where fSYS is off tSST tRSTD Test Conditions VDD — Conditions Min. Typ. Max. Unit fSYS=fH ~ fH/64, fH=fHXT — 128 — tHXT fSYS=fH ~ fH/64, fH=fHIRC — 16 — tHIRC fSYS=fSUB=fLXT — 1024 — tLXT fSYS=fSUB=fLIRC — 2 — tLIRC fSYS=fH ~ fH/64, fH=fHXT or fHIRC — 2 — tH fSYS=fSUB=fLXT or fLIRC — 2 — tSUB fHXT switches from off → on — 1024 — tHXT fHIRC switches from off → on — 16 — tHIRC fLXT switches from off → on — 1024 — tLXT 42 48 54 System Start-up Time Wake-up from Condition where fSYS is on — System Speed Switch Time FAST to Slow Mode or SLOW to FAST Mode — System Reset Delay Time Reset Source from Power-on Reset or LVR Hardware Reset — System Reset Delay Time LVRC/WDTC/RSTC Software Reset — — System Reset Delay Time Reset Source from WDT Overflow or Reset pin reset — — RRPOR=5V/ms ms 14 16 18 Notes: 1. For the System Start-up time values, whether fSYS is on or off depends upon the mode type and the chosen fSYS system oscillator. Details are provided in the System Operating Modes section. 2. The time units, shown by the symbols tHXT, tHIRC etc. are the inverse of the corresponding frequency values as provided in the frequency tables. For example tHIRC=1/fHIRC, tSYS=1/fSYS etc. 3. If the LIRC is used as the system clock and if it is off when in the SLEEP Mode, then an additional LIRC start up time, tSTART, as provided in the LIRC frequency table, must be added to the tSST time in the table above. 4. The System Speed Switch Time is effectively the time taken for the newly activated oscillator to start up. Rev. 1.00 44 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Input/Output Characteristics Ta=25°C Symbol VIL VIH IOL Parameter Test Conditions VDD Min. Typ. Max. 5V — 0 — 1.5 — — 0 — 0.2VDD Input Low Voltage for External Reset Pin — — 0 — 0.4VDD Input High Voltage for I/O Ports or Input Pins 5V — 3.5 — 5.0 — — 0.8VDD — VDD Input High Voltage for External Reset Pin — — 0.9VDD — VDD 16 32 — 32 64 — -0.7 -1.5 — -1.5 -2.9 — VOH=0.9VDD, SLEDCn[m+1:m]=01, n=0, 1, 2, 3 or 4, m=0, 2, 4 or 6 -1.3 -2.5 — -2.5 -5.1 — VOH=0.9VDD, SLEDCn[m+1:m]=10, n=0, 1, 2, 3 or 4, m=0, 2, 4 or 6 -1.8 -3.6 — -3.6 -7.3 — -4.0 -8.0 — 5V VOH=0.9VDD, SLEDCn[m+1:m]=11, n=0, 1, 2, 3 or 4, m=0, 2, 4 or 6 -8.0 -16.0 — 3V — 20 60 100 5V — 10 30 50 Input Low Voltage for I/O Ports or Input Pins Sink Current for I/O Pins 3V 5V 3V 5V 3V 5V IOH Conditions Source Current for I/O Pins 3V 5V 3V RPH Pull-high Resistance for I/O Ports(Note) VOL=0.1VDD VOH=0.9VDD, SLEDCn[m+1:m]=00, n=0, 1, 2, 3 or 4, m=0, 2, 4 or 6 Unit V V mA mA kΩ ILEAK Input leakage current 5V — — ±1 μA tTPI TM Capture Input Minimum Pulse Width — — 0.3 — — μs tTCK TM Clock Input Minimum Pulse Width — — 0.3 — — μs tINT Interrupt Input Pin Minimum Pulse Width — — 10 — — μs tRES External Reset Pin Minimum Pulse Width — — 10 — — μs tSRESET Minimum Software Reset Pulse Width to Reset — — 45 90 120 μs VIN=VDD or VIN=VSS Note: The RPH internal pull high resistance value is calculated by connecting to ground and enabling the input pin with a pull-high resistor and then measuring the input sink current at the specified supply voltage level. Dividing the voltage by this measured current provides the RPH value. Rev. 1.00 45 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Memory Characteristics Ta= -40°C~85°C Symbol Test Conditions Min. Typ. Max. Unit — VDDmin — VDDmax V — — — 2 3 Write cycle time – Data EEPROM Memory — — — 4 6 IDDPGM Programming / Erase current on VDD — — — — 5.0 mA EP Cell Endurance — — 100K — — E/W tRETD ROM Data Retention time — Ta=25°C — 40 — Year — Device in SLEEP Mode 1.0 — — V VRW Parameter VDD Conditions — Erase / Write cycle time – Program Flash Memory VDD for Read / Write Program Flash / Data EEPROM Memory tDEW ms RAM Data Memory VDR RAM Data Retention voltage LVD/LVR Electrical Characteristics Ta=25°C Symbol Parameter Test Conditions Conditions VDD Min. LVR enabled, voltage select 2.1V VLVR VLVD Low Voltage Reset Voltage Low Voltage Detect Voltage — — LVR enabled, voltage select 2.55V LVR enabled, voltage select 3.15V Typ. -5% 2.55 3.15 3.8 LVD enabled, voltage select 2.0V 2.0 LVD enabled, voltage select 2.2V 2.2 LVD enabled, voltage select 2.4V 2.4 LVD enabled, voltage select 3.0V Unit +5% V +5% V 2.1 LVR enabled, voltage select 3.8V LVD enabled, voltage select 2.7V Max. -5% 2.7 3.0 LVD enabled, voltage select 3.3V 3.3 LVD enabled, voltage select 3.6V 3.6 LVD enabled, voltage select 4.0V 4.0 ILVR Additional Current Consumption for LVR Enable — LVD disabled, VBGEN=0 — — 25 μA ILVD Additional Current Consumption for LVD Enable — LVR disabled, VBGEN=0 — — 25 μA — For LVR enable, VBGEN=0, LVD off → on — — 15 μs — For LVR disable, VBGEN=0, LVD off → on — — 150 μs tLVDS LVDO Stable Time tLVR Minimum Low Voltage Width to Reset — — 120 240 480 μs tLVD Minimum Low Voltage Width to Interrupt — — 60 120 240 μs Rev. 1.00 46 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM A/D Converter Characteristics Ta=25°C Symbol Parameter Test Conditions VDD Conditions Min. Typ. Max. Unit VDD Operating Voltage — — 2.7 — 5.5 V VADI Input Voltage — — 0 — VREF V VREF Reference Voltage — — 2 — VDD V VREF=VDD, tADCK=0.5μs or 10μs — — ±3 LSB VREF=VDD, tADCK=0.5μs or 10μs — — ±4 LSB — 0.2 0.4 — 0.3 0.6 3V DNL Differential Non-linearity INL Integral Non-linearity IADC Additional Current Consumption for A/D Converter Enable 3V tADCK Clock Period — — 0.5 — 10 μs tADS Sampling Time — — — 4 — tADCK tADC Conversion Time (Including A/D Sample and Hold Time) — — — 16 — tADCK tON2ST A/D Converter On-to-Start Time — — μs IPGA Additional Current Consumption for PGA Enable 3V VCM PGA Common Mode Voltage Range 3V VOR PGA Maximum Output Voltage Range 3V VVR PGA Fix Voltage Output Rev. 1.00 5V 3V 5V 5V 5V No load, tADCK =0.5μs 4 — — — 300 450 — 400 550 — VSS -0.3 — VDD -1.4 V — VSS +0.1 — VDD -0.1 V No load 5V 5V mA μA 5V Ta= 25°C -1% 2 +1% V 5V Ta= 25°C -1% 3 +1% V 5V Ta= 25°C -1% 4 +1% V 47 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Comparator Electrical Characteristics Ta=25°C Symbol Parameter Test Conditions VDD Conditions Operating Voltage — — ICMP Additional Current Consumption for Comparator Enable 3V VOS Input Offset Voltage * VDD 5V 3V/5V 2.7 — 5.5 — — 3 — 1 3 Without calibration, CNVTn[1:0]=00B, -10 CnOF[4:0]=10000 — 10 -4 — 4 VSS — VDD -1.4 CNVTn[1:0]=00 3V/5V With calibration, CNVTn[1:0]=00B VCM Common Mode Voltage Range AOL Open Loop Gain VHYS Hysteresis — 3V 5V 3V 5V 3V/5V 3V/5V tRP Response Time 3V/5V 3V/5V Min. Typ. Max. CNVTn[1:0]=00 60 — — 60 80 — 10 — 30 10 24 30 With 10mV overdrive, CLOAD=3pF, CNVTn[1:0]=00 — 25 40 With 100mV overdrive, CLOAD=3pF, CNVTn[1:0]=00 — 20 40 With 10mV overdrive, CLOAD=3pF, CNVTn[1:0]=01 — 1.5 4 With 100mV overdrive, CLOAD=3pF, CNVTn[1:0]=01 — 1.2 3 With 10mV overdrive, CLOAD=3pF, CNVTn[1:0]=10 — 0.8 2 With 100mV overdrive, CLOAD=3pF, CNVTn[1:0]=10 — 0.5 1.5 With 10mV overdrive, CLOAD=3pF, CNVTn[1:0]=11 — 0.7 1.5 With 100mV overdrive, CLOAD=3pF, CNVTn[1:0]=11 — 0.3 1 CNVTn[1:0]=00 CNVTn[1:0]=00 Unit V μA mV V dB mV μs Note: The input offset voltage should first be calibrated when the comparator operates with the compared threshold voltage level lower than 250mV. Otherwise, the input offset voltage will be out of specification. Rev. 1.00 48 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCD Driver Electrical Characteristics Ta=25°C Symbol VIN Parameter LCD Operating Voltage Additional Current for LCD Enabled – C type Test Conditions VDD Power supply from PLCD, PLCD[3:0]=1xxxB (for R type) 3.0 — 5.5 — Power supply from PLCD pin (for C type) 2.0 — 3.7 — Power supply from V1 pin (for C type) 3.0 — 5.5 — Power supply from V2 pin (for C type) 1.0 — 1.8 — Power supply from VA (for C type) 3.0 — 5.5 — Power supply from VB (for C type) 2.0 — 3.7 — Power supply from VC (for C type) 2.2 — 5.5 — — 1 — — 2 3V 5V 5V Additional Current for LCD Enabled – R type Min. Typ. Max. Unit — 3V ILCD Conditions 3V 5V 3V 5V 3V ILCDOL LCD Common and Segment Sink Current 5V ILCDOH LCD Common and Segment Source Current 5V 3V No load, VA=V1=VDD, 1/3 bias No load, RT=1170kΩ, VA=PLCD=VDD, 1/3 bias & 1/4 bias No load, RT=225kΩ, VA=PLCD=VDD, 1/3 bias & 1/4 bias No load, RT=60kΩ, VA=PLCD=VDD, 1/3 bias & 1/4 bias No load, VOL=0.1VDD No load, VOH=0.9VDD — 10 15 — 13.5 20 — 16 28 — 21 40 — 50 75 V μA — 80 120 210 420 — 350 700 — -80 -160 — -180 -360 — μA μA I2C Characteristics Ta=25°C Symbol Parameter VDD Condition Min. Typ. Max. System Frequency for I2C Standard Mode (100kHz) — No clock debounce 2 — — — 2 system clocks debounce 4 — — — 4 system clocks debounce 8 — — System Frequency for I2C Fast Mode (400kHz) — No clock debounce 5 — — — 2 system clocks debounce 10 — — — 4 system clocks debounce 20 — — fI2C Rev. 1.00 Test Condition 49 Unit MHz MHz December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Power-on Reset Characteristics Ta=25°C Symbol Test Conditions Parameter VDD Conditions Min. Typ. Max. Unit VPOR VDD Start Voltage to Ensure Power-on Reset — — — — 100 mV RRPOR VDD Rising Rate to Ensure Power-on Reset — — 0.035 — — V/ms tPOR Minimum Time for VDD Stays at VPOR to Ensure Power-on Reset — — 1 — — ms VDD RRPOR VPOR Time tPOR Rev. 1.00 50 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM System Architecture A key factor in the high-performance features of the Holtek range of microcontrollers is attributed to their internal system architecture. The range of devices take advantage of the usual features found within RISC microcontrollers providing increased speed of operation and enhanced performance. The pipelining scheme is implemented in such a way that instruction fetching and instruction execution are overlapped, hence instructions are effectively executed in one cycle, with the exception of branch or call instructions. An 8-bit wide ALU is used in practically all instruction set operations, which carries out arithmetic operations, logic operations, rotation, increment, decrement, branch decisions, etc. The internal data path is simplified by moving data through the Accumulator and the ALU. Certain internal registers are implemented in the Data Memory and can be directly or indirectly addressed. The simple addressing methods of these registers along with additional architectural features ensure that a minimum of external components is required to provide a functional I/O and A/D control system with maximum reliability and flexibility. This makes these devices suitable for low-cost, high-volume production for controller applications. Clocking and Pipelining The main system clock, derived from either a HXT, LXT, HIRC or LIRC oscillator is subdivided into four internally generated non-overlapping clocks, T1~T4. The Program Counter is incremented at the beginning of the T1 clock during which time a new instruction is fetched. The remaining T2~T4 clocks carry out the decoding and execution functions. In this way, one T1~T4 clock cycle forms one instruction cycle. Although the fetching and execution of instructions takes place in consecutive instruction cycles, the pipelining structure of the microcontroller ensures that instructions are effectively executed in one instruction cycle. The exception to this are instructions where the contents of the Program Counter are changed, such as subroutine calls or jumps, in which case the instruction will take one more instruction cycle to execute. For instructions involving branches, such as jump or call instructions, two machine cycles are required to complete instruction execution. An extra cycle is required as the program takes one cycle to first obtain the actual jump or call address and then another cycle to actually execute the branch. The requirement for this extra cycle should be taken into account by programmers in timing sensitive applications. fSYS (System Clock) Phase Clock T1 Phase Clock T2 Phase Clock T3 Phase Clock T4 Program Counter Pipelining PC PC+1 Fetch Inst. (PC) Execute Inst. (PC-1) Fetch Inst. (PC+1) Execute Inst. (PC) PC+2 Fetch Inst. (PC+2) Execute Inst. (PC+1) System Clocking and Pipelining Rev. 1.00 51 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 1 MOV A,[12H] 2 CALL DELAY 3 CPL [12H] 4 : 5 : 6 DELAY: NOP Fetch Inst. 1 Execute Inst. 1 Fetch Inst. 2 Execute Inst. 2 Fetch Inst. 3 Flush Pipeline Fetch Inst. 6 Execute Inst. 6 Fetch Inst. 7 Instruction Fetching Program Counter During program execution, the Program Counter is used to keep track of the address of the next instruction to be executed. It is automatically incremented by one each time an instruction is executed except for instructions, such as “JMP” or “CALL” that demand a jump to a nonconsecutive Program Memory address. For devices with a Program Memory capacity in excess of 8K words, the Program Memory high byte address must be setup by selecting a certain program memory bank which is implemented using the program memory bank pointer bits, PBPn. Only the lower 8 bits, known as the Program Counter Low Register, are directly addressable by the application program. When executing instructions requiring jumps to non-consecutive addresses such as a jump instruction, a subroutine call, interrupt or reset, etc., the microcontroller manages program control by loading the required address into the Program Counter. For conditional skip instructions, once the condition has been met, the next instruction, which has already been fetched during the present instruction execution, is discarded and a dummy cycle takes its place while the correct instruction is obtained. Device Program Counter High Byte Low Byte (PCL) HT67F2350 PC12~PC8 PC7~PC0 HT67F2360 PBP0, PC12~PC8 PC7~PC0 HT67F2370 PBP1~PBP0, PC12~PC8 PC7~PC0 HT67F2390 PBP2~PBP0, PC12~PC8 PC7~PC0 Program Counter The lower byte of the Program Counter, known as the Program Counter Low register or PCL, is available for program control and is a readable and writeable register. By transferring data directly into this register, a short program jump can be executed directly; however, as only this low byte is available for manipulation, the jumps are limited to the present page of memory that is 256 locations. When such program jumps are executed it should also be noted that a dummy cycle will be inserted. Manipulating the PCL register may cause program branching, so an extra cycle is needed to pre-fetch. Rev. 1.00 52 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Stack This is a special part of the memory which is used to save the contents of the Program Counter only. The stack has multiple levels and is neither part of the data nor part of the program space, and is neither readable nor writeable. The activated level is indexed by the Stack Pointer, and is neither readable nor writeable. At a subroutine call or interrupt acknowledge signal, the contents of the Program Counter are pushed onto the stack. At the end of a subroutine or an interrupt routine, signaled by a return instruction, RET or RETI, the Program Counter is restored to its previous value from the stack. After a device reset, the Stack Pointer will point to the top of the stack. If the stack is full and an enabled interrupt takes place, the interrupt request flag will be recorded but the acknowledge signal will be inhibited. When the Stack Pointer is decremented, by RET or RETI, the interrupt will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily. However, when the stack is full, a CALL subroutine instruction can still be executed which will result in a stack overflow. Precautions should be taken to avoid such cases which might cause unpredictable program branching. If the stack is overflow, the first Program Counter save in the stack will be lost. Program Counter Top of Stack Stack Level 1 Stack Level 2 Stack Pointer Stack Level 3 Bottom of Stack Stack Level 16 : : : Program Memory Arithmetic and Logic Unit – ALU The arithmetic-logic unit or ALU is a critical area of the microcontroller that carries out arithmetic and logic operations of the instruction set. Connected to the main microcontroller data bus, the ALU receives related instruction codes and performs the required arithmetic or logical operations after which the result will be placed in the specified register. As these ALU calculation or operations may result in carry, borrow or other status changes, the status register will be correspondingly updated to reflect these changes. The ALU supports the following functions: • Arithmetic operations: ADD, ADDM, ADC, ADCM, SUB, SUBM, SBC, SBCM, DAA LADD, LADDM, LADC, LADCM, LSUB, LSUBM, LSBC, LSBCM, LDAA • Logic operations: AND, OR, XOR, ANDM, ORM, XORM, CPL, CPLA LAND, LOR, LXOR, LANDM, LORM, LXORM, LCPL, LCPLA • Rotation: RRA, RR, RRCA, RRC, RLA, RL, RLCA, RLC LRRA, LRR, LRRCA, LRRC, LRLA, LRL, LRLCA, LRLC • Increment and Decrement: INCA, INC, DECA, DEC LINCA, LINC, LDECA, LDEC • Branch decision: JMP, SZ, SZA, SNZ, SIZ, SDZ, SIZA, SDZA, CALL, RET, RETI LSZ, LSZA, LSNZ, LSIZ, LSDZ, LSIZA, LSDZA Rev. 1.00 53 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Flash Program Memory The Program Memory is the location where the user code or program is stored. For these devices series the Program Memory are Flash type, which means it can be programmed and re-programmed a large number of times, allowing the user the convenience of code modification on the same device. By using the appropriate programming tools, these Flash devices offer users the flexibility to conveniently debug and develop their applications while also offering a means of field programming and updating. Device Capacity HT67F2350 8K × 16 Banks — HT67F2360 16K × 16 0~1 HT67F2370 32K × 16 0~3 HT67F2390 64K × 16 0~7 Structure The Program Memory has a capacity of 8K×16 to 64K×16 bits. The Program Memory is addressed by the Program Counter and also contains data, table information and interrupt entries. Table data, which can be setup in any location within the Program Memory, is addressed by a separate table pointer registers. Special Vectors Within the Program Memory, certain locations are reserved for the reset and interrupts. The location 000H is reserved for use by these devices reset for program initialisation. After a device reset is initiated, the program will jump to this location and begin execution. Look-up Table Any location within the Program Memory can be defined as a look-up table where programmers can store fixed data. To use the look-up table, the table pointer must first be setup by placing the address of the look up data to be retrieved in the table pointer register, TBLP and TBHP. These registers define the total address of the look-up table. After setting up the table pointer, the table data can be retrieved from the Program Memory using the "TABRD [m]" or "TABRDL [m]" instructions respectively when the memory [m] is located in sector 0. If the memory [m] is located in other sectors except sector 0, the data can be retrieved from the program memory using the corresponding extended table read instruction such as "LTABRD [m]" or "LTABRDL [m]" respectively. When the instruction is executed, the lower order table byte from the Program Memory will be transferred to the user defined Data Memory register [m] as specified in the instruction. The higher order table data byte from the Program Memory will be transferred to the TBLH special register. Any unused bits in this transferred higher order byte will be read as "0". The accompanying diagram illustrates the addressing data flow of the look-up table. Program Memory Add�ess Last Page o� TBHP Registe� TBLP Registe� Rev. 1.00 Data 1� �its Registe� TBLH Use� Sele�ted Registe� High Byte Low Byte 54 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 000H HT67F2350 HT67F2360 HT67F2370 HT67F2390 Initialisation Vector Initialisation Vector Initialisation Vector Initialisation Vector Interrupt Vectors Interrupt Vectors Interrupt Vectors Interrupt Vectors Look-up Table Look-up Table Look-up Table Look-up Table 16 bits 16 bits 16 bits 16 bits Bank 1 Bank 1 Bank 1 Bank 2 Bank 2 Bank 3 Bank 3 004H 03CH n00H nFFH 1FFFH 2000H 3FFFH 4000H 5FFFH 6000H 7FFFH 8000H Bank 4 9FFFH A000H Bank 5 BFFFH C000H Bank 6 DFFFH E000H Bank 7 FFFFH Program Memory Structure Rev. 1.00 55 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Table Program Example The accompanying example shows how the table pointer and table data is defined and retrieved from the device. This example uses raw table data located in the last page which is stored there using the ORG statement. The value at this ORG statement is "1F00H" which refers to the start address of the last page within the 8K Program Memory of the device. The table pointer low byte register is setup here to have an initial value of "06H". This will ensure that the first data read from the data table will be at the Program Memory address "1F06H" or 6 locations after the start of the last page. Note that the value for the table pointer is referenced to the first address of the present page pointed by the TBHP register if the "TABRD [m]" instruction is being used. The high byte of the table data which in this case is equal to zero will be transferred to the TBLH register automatically when the "TABRD [m]" instruction is executed. Because the TBLH register is a read/write register and can be restored, care should be taken to ensure its protection if both the main routine and Interrupt Service Routine use table read instructions. If using the table read instructions, the Interrupt Service Routines may change the value of the TBLH and subsequently cause errors if used again by the main routine. As a rule it is recommended that simultaneous use of the table read instructions should be avoided. However, in situations where simultaneous use cannot be avoided, the interrupts should be disabled prior to the execution of any main routine table-read instructions. Note that all table related instructions require two instruction cycles to complete their operation. Table Read Program Example tempreg1 db ? ; temporary register #1 tempreg2 db ? ; temporary register #2 : mov a,06h ; initialise low table pointer - note that this address is referenced mov tblp,a ; to the last page or the page that tbhp pointed mov a,1fh ; initialise high table pointer mov tbhp,a : tabrd tempreg1 ; transfers value in table referenced by table pointer data at program ; memory address "1F06H" transferred to tempreg1 and TBLH dec tblp ; reduce value of table pointer by one tabrd tempreg2 ; transfers value in table referenced by table pointer data at program ; memory address "1F05H" transferred to tempreg2 and TBLH in this ; example the data "1AH" is transferred to tempreg1 and data "0FH" to ; register tempreg2 : org 1F00h ; sets initial address of program memory dc 00Ah, 00Bh, 00Ch, 00Dh, 00Eh, 00Fh, 01Ah, 01Bh : Rev. 1.00 56 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM In Circuit Programming – ICP The provision of Flash type Program Memory provides the user with a means of convenient and easy upgrades and modifications to their programs on the same device. As an additional convenience, Holtek has provided a means of programming the microcontroller incircuit using a 4-pin interface. This provides manufacturers with the possibility of manufacturing their circuit boards complete with a programmed or un-programmed microcontroller, and then programming or upgrading the program at a later stage. This enables product manufacturers to easily keep their manufactured products supplied with the latest program releases without removal and reinsertion of the device. Holtek Writer Pins MCU Programming Pins ICPDA PA0 Programming Serial Data/Address Pin Description ICPCK PA2 Programming Clock VDD VDD Power Supply VSS VSS Ground The Program Memory and EEPROM data memory can be programmed serially in-circuit using this 4-wire interface. Data is downloaded and uploaded serially on a single pin with an additional line for the clock. Two additional lines are required for the power supply. The technical details regarding the in-circuit programming of the device are beyond the scope of this document and will be supplied in supplementary literature. During the programming process, the user must take care of the ICPDA and ICPCK pins for data and clock programming purposes to ensure that no other outputs are connected to these two pins. W�ite� Conne�to� Signals MCU P�og�a��ing Pins W�ite�_VDD VDD ICPDA PA0 ICPCK PA� W�ite�_VSS VSS * * To othe� Ci��uit Note: * may be resistor or capacitor. The resistance of * must be greater than 1k or the capacitance of * must be less than 1nF. Rev. 1.00 57 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM On-Chip Debug Support – OCDS There is an EV chip named HT67V23x0 which is used to emulate the real MCU device named HT67F23x0. The EV chip device also provides the "On-Chip Debug" function to debug the real MCU device during development process. The EV chip and real MCU devices, HT67V23x0 and HT67F23x0, are almost functional compatible except the "On-Chip Debug" function. Users can use the EV chip device to emulate the real MCU device behaviors by connecting the OCDSDA and OCDSCK pins to the Holtek HT-IDE development tools. The OCDSDA pin is the OCDS Data/Address input/output pin while the OCDSCK pin is the OCDS clock input pin. When users use the EV chip device for debugging, the corresponding pin functions shared with the OCDSDA and OCDSCK pins in the real MCU device will have no effect in the EV chip. However, the two OCDS pins which are pin-shared with the ICP programming pins are still used as the Flash Memory programming pins for ICP. For more detailed OCDS information, refer to the corresponding document named "Holtek e-Link for 8-bit MCU OCDS User’s Guide". Holtek e-Link Pins EV Chip OCDS Pins Pin Description OCDSDA OCDSDA On-Chip Debug Support Data/Address input/output OCDSCK OCDSCK On-Chip Debug Support Clock input VDD VDD Power Supply VSS VSS Ground In Application Programming – IAP These devices offer IAP function to update data or application program to flash ROM. Users can define any ROM location for IAP, but there are some features which user must notice in using IAP function. Configurations HT67F2350 HT67F2360/HT67F2370 HT67F2390 Erase Page 32 words / page 64 words / page 128 words / page Writing Word 32 words / time 64 words / time 128 words / time Reading Word 1 word / time 1 word / time 1 word / time In Application Programming Control Registers The Address register, FARL and FARH, the Data registers, FD0L/FD0H, FD1L/FD1H, FD2L/FD2H and FD3L/FD3H, and the Control registers, FC0, FC1 and FC2, are the corresponding Flash access registers located in Data Memory sector 0 and sector 1 respectively for IAP. If using the indirect addressing method to access the FC0, FC1 and FC2 registers, all read and write operations to the registers must be performed using the Indirect Addressing Register, IAR1 or IAR2, and the Memory Pointer pair, MP1L/MP1H or MP2L/MP2H. Because the FC0, FC1 and FC2 control registers are located at the address of 43H~45H in Data Memory sector 1, the desired value ranged from 43H to 45H must first be written into the MP1L or MP2L Memory Pointer low byte and the value "01H" must also be written into the MP1H or MP2H Memory Pointer high byte. Rev. 1.00 58 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Register Name Bit 7 6 5 4 3 CFWEN FMOD2 FMOD1 FMOD0 FWPEN FC0 2 1 0 FWT FRDEN FRD FC1 D7 D6 D5 D4 D3 D2 D1 D0 FC2 — — — — — — — CLWB FARL A7 A6 A5 A4 A3 A2 A1 A0 FARH (HT67F2350) — — — A12 A11 A10 A9 A8 FARH (HT67F2360) — — A13 A12 A11 A10 A9 A8 FARH (HT67F2370) — A14 A13 A12 A11 A10 A9 A8 FARH (HT67F2390) A15 A14 A13 A12 A11 A10 A9 A8 FD0L D7 D6 D5 D4 D3 D2 D1 D0 D8 FD0H D15 D14 D13 D12 D11 D10 D9 FD1L D7 D6 D5 D4 D3 D2 D1 D0 FD1H D15 D14 D13 D12 D11 D10 D9 D8 FD2L D7 D6 D5 D4 D3 D2 D1 D0 D8 FD2H D15 D14 D13 D12 D11 D10 D9 FD3L D7 D6 D5 D4 D3 D2 D1 D0 FD3H D15 D14 D13 D12 D11 D10 D9 D8 IAP Registers List • FC0 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name CFWEN FMOD2 FMOD1 FMOD0 FWPEN FWT FRDEN FRD R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 CFWEN: Flash Memory Write enable control 0: Flash memory write function is disabled 1: Flash memory write function has been successfully enabled When this bit is cleared to 0 by application program, the Flash memory write function is disabled. Note that writing a "1" into this bit results in no action. This bit is used to indicate that the Flash memory write function status. When this bit is set to 1 by hardware, it means that the Flash memory write function is enabled successfully. Otherwise, the Flash memory write function is disabled as the bit content is zero. Bit 6~4 FMOD2~FMOD0: Mode selection 000: Write program memory 001: Page erase program memory 010: Reserved 011: Read program memory 10x: Reserved 110: FWEN mode – Flash memory Write function Enabled mode 111: Reserved Bit 3 FWPEN: Flash memory Write Procedure Enable control 0: Disable 1: Enable When this bit is set to 1 and the FMOD field is set to "110", the IAP controller will execute the "Flash memory write function enable" procedure. Once the Flash memory write function is successfully enabled, it is not necessary to set the FWPEN bit any more. 59 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 2 FWT: Flash memory Write Initiate control 0: Do not initiate Flash memory write or Flash memory write process is completed 1: Initiate Flash memory write process This bit is set by software and cleared by hardware when the Flash memory write process is completed. Bit 1 FRDEN: Flash memory Read Enable control 0: Flash memory read disable 1: Flash memory read enable Bit 0 FRD: Flash memory Read Initiate control 0: Do not initiate Flash memory read or Flash memory read process is completed 1: Initiate Flash memory read process This bit is set by software and cleared by hardware when the Flash memory read process is completed. • FC1 Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 D7~D0: Whole chip reset pattern When user writes a specific value of "55H" to this register, it will generate a reset signal to reset whole chip. • FC2 Register Bit 7 6 5 4 3 2 1 0 Name — — — — — — — CLWB R/W — — — — — — — R/W POR — — — — — — — 0 Bit 7~1 Unimplemented, read as "0" Bit 0 CLWB: Flash memory Write Buffer Clear control 0: Do not initiate Write Buffer Clear process or Write Buffer Clear process is completed 1: Initiate Write Buffer Clear process This bit is set by software and cleared by hardware when the Write Buffer Clear process is completed. • FARL Register Bit 7 6 5 4 3 2 1 0 Name A7 A6 A5 A4 A3 A2 A1 A0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 4 3 2 1 0 Bit 7~0 Flash Memory Address bit 7 ~ bit 0 • FARH Register – HT67F2350 Bit Rev. 1.00 7 6 5 Name — — — A12 A11 A10 A9 A8 R/W — — — R/W R/W R/W R/W R/W POR — — — 0 0 0 0 0 Bit 7~5 Unimplemented, read as "0" Bit 4~0 Flash Memory Address bit 12 ~ bit 8 60 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • FARH Register – HT67F2360 Bit 7 6 5 4 3 2 1 0 Name — — A13 A12 A11 A10 A9 A8 R/W — — R/W R/W R/W R/W R/W R/W POR — — 0 0 0 0 0 0 Bit 7~6 Unimplemented, read as "0" Bit 5~0 Flash Memory Address bit 13 ~ bit 8 • FARH Register – HT67F2370 Bit 7 6 5 4 3 2 1 0 Name — A14 A13 A12 A11 A10 A9 A8 R/W — R/W R/W R/W R/W R/W R/W R/W POR — 0 0 0 0 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6~0 Flash Memory Address bit 14 ~ bit 8 • FARH Register – HT67F2390 Bit 7 6 5 4 3 2 1 0 Name A15 A14 A13 A12 A11 A10 A9 A8 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Flash Memory Address bit 15 ~ bit 8 • FD0L Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 The first Flash Memory data bit 7 ~ bit 0 Note that the data written into the low byte data register FD0L will only be stored in the FD0L register and not be loaded into the lower 8-bit write buffer. • FD0H Register Bit 7 6 5 4 3 2 1 0 Name D15 D14 D13 D12 D11 D10 D9 D8 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 The first Flash Memory data bit 15 ~ bit 8 Note that when the 8-bit data is written into the high byte data register FD0H, the whole 16-bit data stored in the FD0H and FD0L registers will simultaneously be loaded into the 16-bit write buffer and then the content of the Flash Memory address register pair, FARH and FARL, will be incremented by one. • FD1L Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Rev. 1.00 The second Flash Memory data bit 7 ~ bit 0 61 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • FD1H Register Bit 7 6 5 4 3 2 1 0 Name D15 D14 D13 D12 D11 D10 D9 D8 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 The second Flash Memory data bit 15 ~ bit 8 • FD2L Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 3 2 1 0 Bit 7~0 The third Flash Memory data bit 7 ~ bit 0 • FD2H Register Bit 7 6 5 4 Name D15 D14 D13 D12 D11 D10 D9 D8 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 The third Flash Memory data bit 15 ~ bit 8 • FD3L Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 The fourth Flash Memory data bit 7 ~ bit 0 • FD3H Register Bit 7 6 5 4 3 2 1 0 Name D15 D14 D13 D12 D11 D10 D9 D8 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Rev. 1.00 The fourth Flash Memory data bit 15 ~ bit 8 62 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Flash Memory Write Function Enable Procedure In order to allow users to change the Flash memory data through the IAP control registers, users must first enable the Flash memory write operation by the following procedure: Step 1. Write "110" into the FMOD2~FMOD0 bits to select the FWEN mode. Step 2. Set the FWPEN bit to "1". The step 1 and step 2 can be executed simultaneously. Step 3. The pattern data with a sequence of 00H, 04H, 0DH, 09H, C3H and 40H must be written into the FD1L, FD1H, FD2L, FD2H, FD3L and FD3H registers respectively. Step 4. A counter with a time-out period of 300μs will be activated to allow users writing the correct pattern data into the FD1L/FD1H ~ FD3L/FD3H register pairs. The counter clock is derived from the LIRC oscillator. Step 5. If the counter overflows or the pattern data is incorrect, the Flash memory write operation will not be enabled and users must again repeat the above procedure. Then the FWPEN bit will automatically be cleared to 0 by hardware. Step 6. If the pattern data is correct before the counter overflows, the Flash memory write operation will be enabled and the FWPEN bit will automatically be cleared to 0 by hardware. The CFWEN bit will also be set to 1 by hardware to indicate that the Flash memory write operation is successfully enabled. Step 7. Once the Flash memory write operation is enabled, the user can change the Flash ROM data through the Flash control register. Step 8. To disable the Flash memory write operation, the user can clear the CFWEN bit to 0. Is �ounte� ove�flow ? Flash Me�o�y W�ite Fun�tion Ena�le P�o�edu�e No Yes FWPEN=0 Set FMOD [�:0] =110 & FWPEN=1 Sele�t FWEN �ode & Sta�t Flash w�ite Ha�dwa�e a�tivate a �ounte� Is patte�n �o��e�t ? W�tie the following patte�n to Flash Data �egiste�s FD1L= 00h � FD1H = 04h FD�L= 0Dh � FD�H = 09h FD3L= C3h � FD3H = 40h No Yes CFWEN = 1 CFWEN=0 Su��ess Failed END Flash Memory Write Function Enable Procedure Rev. 1.00 63 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Flash Memory Read/Write Procedure After the Flash memory write function is successfully enabled through the preceding IAP procedure, users must first erase the corresponding Flash memory block or page and then initiate the Flash memory write operation. For these devices the number of the page erase operation is 32, 64 and 128 words per page respectively, the available page erase address is specified by FARH register and the content of FARL [7:5], FARL [7:6] and FARL [7] bit field respectively. Erase Page FARH FARL [7:5] 0 0000 0000 000 FARL [4:0] x xxxx 1 0000 0000 001 x xxxx 2 0000 0000 010 x xxxx 3 0000 0000 011 x xxxx 4 0000 0000 100 x xxxx : : : : : : : : 254 0001 1111 110 x xxxx 255 0001 1111 111 x xxxx "x": don’t care HT67F2350 Erase Page Number and Selection Erase Page FARH FARL [7:6] FARL [5:0] 0 0000 0000 00 xx xxxx 1 0000 0000 01 xx xxxx 2 0000 0000 10 xx xxxx 3 0000 0000 11 xx xxxx 4 0000 0001 00 xx xxxx : : : : : : : : 254 0011 1111 10 xx xxxx 255 0011 1111 11 xx xxxx "x": don’t care HT67F2360 Erase Page Number and Selection Erase Page FARH FARL [7:6] FARL [5:0] 0 0000 0000 00 xx xxxx 1 0000 0000 01 xx xxxx 2 0000 0000 10 xx xxxx 3 0000 0000 11 xx xxxx 4 0000 0001 00 xx xxxx : : : : : : : : 510 0111 1111 10 xx xxxx 511 0111 1111 11 xx xxxx "x": don’t care HT67F2370 Erase Page Number and Selection Rev. 1.00 64 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Erase Page FARH FARL [7] FARL [6:0] 0 0000 0000 0 xxx xxxx 1 0000 0000 1 xxx xxxx 2 0000 0001 0 xxx xxxx 3 0000 0001 1 xxx xxxx 4 0000 0010 0 xxx xxxx : : : : : : : : 510 1111 1111 0 xxx xxxx 511 1111 1111 1 xxx xxxx "x": don’t care HT67F2390 Erase Page Number and Selection Read Flash Me�o�y Set FMOD [�:0]=011 & FRDEN=1 Set Flash Add�ess �egiste�s FARH=xxh� FARL=xxh Set FRD=1 No FRD=0 ? Yes Read data value: FD0L=xxh� FD0H=xxh Read Finish ? No Yes Clea� FRDEN �it END Read Flash Memory Procedure Rev. 1.00 65 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM W�ite Flash Me�o�y Flash Me�o�y W�ite Fun�tion Ena�le P�o�edu�e Set Page E�ase add�ess: FARH/FARL Set FMOD [�:0]=001 & FWT=1 Sele�t “Page E�ase �ode” & Initiate w�ite ope�ation No FWT=0 ? Yes Set FMOD [�:0]=000 Sele�t “W�ite Flash Mode” Set W�ite sta�ting add�ess: FARH/FARL W�ite data to data �egiste�: FD0L/FD0H No Page data W�ite finish Yes Set FWT=1 No FWT=0 ? Yes W�ite Finish ? No Yes Clea� CFWEN=0 END Write Flash Memory Procedure Note: When the FWT or FRD bit is set to 1, the MCU is stopped. Rev. 1.00 66 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Data Memory The Data Memory is an 8-bit wide RAM internal memory and is the location where temporary information is stored. Divided into three types, the first of Data Memory is an area of RAM where special function registers are located. These registers have fixed locations and are necessary for correct operation of the device. Many of these registers can be read from and written to directly under program control, however, some remain protected from user manipulation. The second area of Data Memory is reserved for general purpose use. All locations within this area are read and write accessible under program control. The third area is reserved for the LCD Data Memory. This special area of Data Memory is mapped directly to the LCD display so data written into this memory area will directly affect the displayed data. Switching between the different Data Memory sectors is achieved by properly setting the Memory Pointers to correct value. Structure The Data Memory is subdivided into several sectors, all of which are implemented in 8-bit wide Memory. Each of the Data Memory sectors is generally categorized into two types, the Special Purpose Data Memory and the General Purpose Data Memory. However, the Data Memory Sector 4 is reserved for the LCD displayed data. The address range of the Special Purpose Data Memory for the device is from 00H to 7FH while the General Purpose Data Memory address range is from 80H to FFH. Device Special Purpose Data Memory Sectors LCD Data Memory Capacity Sector: Address General Purpose Data Memory Capacity Sector: Address HT67F2350 0, 1 56 × 8 4: 00H~37H 768 × 8 0: 80H~FFH 1: 80H~FFH : 5: 80H~FFH HT67F2360 0, 1 56 × 8 4: 00H~37H 1536 × 8 0: 80H~FFH 1: 80H~FFH : 11: 80H~FFH 3072 × 8 0: 80H~FFH 1: 80H~FFH : 23: 80H~FFH 4096 × 8 0: 80H~FFH 1: 80H~FFH : 31: 80H~FFH HT67F2370 HT67F2390 0, 1, 2 0, 1, 2 56 × 8 56 × 8 4: 00H~37H 4: 00H~37H Data Memory Summary Rev. 1.00 67 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Sector 2 only for HT67F2370/90 00H LCD Memory in Sector 4 Special Purpose Data Memory (Sector 0 ~ Sector 1) 7FH 80H General Purpose Data Memory (Sector 0 ~ Sector N) Sector 0 Sector 1 FFH Sector N Note: N= 5 for HT67F2350; N=11 for HT67F2360; N=23 for HT67F2370; N=31 for HT67F2390 Data Memory Structure Data Memory Addressing For these devices that support the extended instructions, there is no Bank Pointer for Data Memory. The Bank Pointer, PBP, is only available for Program Memory. For Data Memory the desired Sector is pointed by the MP1H or MP2H register and the certain Data Memory address in the selected sector is specified by the MP1L or MP2L register when using indirect addressing access. Direct Addressing can be used in all sectors using the corresponding instruction which can address all available data memory space. For the accessed data memory which is located in any data memory sectors except sector 0, the extended instructions can be used to access the data memory instead of using the indirect addressing access. The main difference between standard instructions and extended instructions is that the data memory address "m" in the extended instructions can be from 11 bits to 13 bits depending upon which device is selected, the high byte indicates a sector and the low byte indicates a specific address. General Purpose Data Memory All microcontroller programs require an area of read/write memory where temporary data can be stored and retrieved for use later. It is this area of RAM memory that is known as General Purpose Data Memory. This area of Data Memory is fully accessible by the user programming for both reading and writing operations. By using the bit operation instructions individual bits can be set or reset under program control giving the user a large range of flexibility for bit manipulation in the Data Memory. Special Purpose Data Memory This area of Data Memory is where registers, necessary for the correct operation of the microcontroller, are stored. Most of the registers are both readable and writeable but some are protected and are readable only, the details of which are located under the relevant Special Function Register section. Note that for locations that are unused, any read instruction to these addresses will return the value "00H". Rev. 1.00 68 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 00H 01H 0�H 03H 04H 05H 0�H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 1�H 13H 14H 15H 1�H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH �0H �1H ��H �3H �4H �5H ��H �7H �8H �9H �AH �BH �CH �DH �EH �FH 30H 31H 3�H 33H 34H 35H 3�H 37H 38H 39H 3AH 3BH 3CH 3DH 3EH 3FH Se�to� 0 IAR0 MP0 IAR1 MP1L MP1H ACC PCL TBLP TBLH TBHP STATUS IAR� MP�L MP�H RSTFC INTC0 INTC1 INTC� INTC3 PA PAC PAPU PAWU PB PBC PBPU PC PCC PCPU PD PDC PDPU PE PEC PEPU PF PFC PFPU PG PGC PGPU PJ PJC PJPU CRCCR CRCIN CRCDL CRCDH IECC RSTC VBGRC INTEG SCC HIRCC HXTC LXTC WDTC LVRC Se�to� 1 PTM0C0 PTM0C1 PTM0DL PTM0DH PTM0AL PTM0AH PTM0RPL PTM0RPH STM0C0 STM0C1 STM0DL STM0DH STM0AL STM0AH STM0RP 40H 41H 4�H 43H 44H 45H 4�H 47H 48H 49H 4AH 4BH 4CH 4DH 4EH 4FH 50H 51H 5�H 53H 54H 55H 5�H 57H 58H 59H 5AH 5BH 5CH 5DH 5EH 5FH �0H �1H ��H �3H �4H �5H ��H �7H �8H �9H �AH �BH �CH �DH �EH �FH 70H 71H 7�H 73H 74H 75H 7�H 77H 78H 79H 7AH 7BH 7CH 7DH 7EH 7FH U0SR U0CR1 U0CR� TXR_RXR0 BRG0 U1SR U1CR1 U1CR� TXR_RXR1 BRG1 PTM1C0 PTM1C1 PTM1DL PTM1DH PTM1AL PTM1AH PTM1RPL PTM1RPH PTM�C0 PTM�C1 PTM�DL PTM�DH PTM�AL PTM�AH PTM�RPL PTM�RPH PTM3C0 PTM3C1 PTM3DL PTM3DH PTM3AL PTM3AH PTM3RPL PTM3RPH STM1C0 STM1C1 STM1DL STM1DH STM1AL STM1AH STM1RP STM�C0 STM�C1 STM�DL STM�DH STM�AL STM�AH STM�RP Se�to� 0 LVDC EEA Se�to� 1 EEC EED CP0C CP1C MFI0 MFI1 MFI� MFI3 MFI4 MFI5 MFI� MFI7 MFI8 MFI9 LCDC0 LCDC1 LCDC� SLEDC0 SLEDC1 SLEDC� SLEDC3 SLEDC4 FC0 FC1 FC� MDUWR0 MDUWR1 MDUWR� MDUWR3 MDUWR4 MDUWR5 MDUWCTRL CP0VOS CP1VOS PSC0R TB0C TB1C PSC1R SADOL SADOH SADC0 SADC1 SADC� SIMC0 SIMC1 SIMD SIMA/SIMC� SIMTOC SPIAC0 SPIAC1 SPIAD FARL FARH FD0L FD0H FD1L FD1H FD�L FD�H FD3L FD3H IFS0 IFS1 IFS� IFS4 PAS0 PAS1 PBS0 PBS1 PCS0 PCS1 PDS0 PDS1 PES0 PES1 PFS0 PFS1 PGS1 PJS0 PJS1 PTM4C0 PTM4C1 PTM4DL PTM4DH PTM4AL PTM4AH PTM4RPL PTM4RPH PTM5C0 PTM5C1 PTM5DL PTM5DH PTM5AL PTM5AH PTM5RPL PTM5RPH PTM�C0 PTM�C1 PTM�DL PTM�DH PTM�AL PTM�AH PTM�RPL PTM�RPH PTM7C0 PTM7C1 PTM7DL PTM7DH PTM7AL PTM7AH PTM7RPL PTM7RPH : Unused� �ead as 00H Special Purpose Data Memory Structure – HT67F2350 Rev. 1.00 69 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 00H 01H 0�H 03H 04H 05H 0�H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 1�H 13H 14H 15H 1�H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH �0H �1H ��H �3H �4H �5H ��H �7H �8H �9H �AH �BH �CH �DH �EH �FH 30H 31H 3�H 33H 34H 35H 3�H 37H 38H 39H 3AH 3BH 3CH 3DH 3EH 3FH Se�to� 0 IAR0 MP0 IAR1 MP1L MP1H ACC PCL TBLP TBLH TBHP STATUS PBP IAR� MP�L MP�H RSTFC INTC0 INTC1 INTC� INTC3 PA PAC PAPU PAWU PB PBC PBPU PC PCC PCPU PD PDC PDPU PE PEC PEPU PF PFC PFPU PG PGC PGPU PH PHC PHPU PJ PJC PJPU CRCCR CRCIN CRCDL CRCDH IECC RSTC VBGRC INTEG SCC HIRCC HXTC LXTC WDTC LVRC Se�to� 1 PTM0C0 PTM0C1 PTM0DL PTM0DH PTM0AL PTM0AH PTM0RPL PTM0RPH STM0C0 STM0C1 STM0DL STM0DH STM0AL STM0AH STM0RP 40H 41H 4�H 43H 44H 45H 4�H 47H 48H 49H 4AH 4BH 4CH 4DH 4EH 4FH 50H 51H 5�H 53H 54H 55H 5�H 57H 58H 59H 5AH 5BH 5CH 5DH 5EH 5FH �0H �1H ��H �3H �4H �5H ��H �7H �8H �9H �AH �BH �CH �DH �EH �FH 70H 71H 7�H 73H 74H 75H 7�H 77H 78H 79H 7AH 7BH 7CH 7DH 7EH 7FH U0SR U0CR1 U0CR� TXR_RXR0 BRG0 U1SR U1CR1 U1CR� TXR_RXR1 BRG1 PTM1C0 PTM1C1 PTM1DL PTM1DH PTM1AL PTM1AH PTM1RPL PTM1RPH PTM�C0 PTM�C1 PTM�DL PTM�DH PTM�AL PTM�AH PTM�RPL PTM�RPH PTM3C0 PTM3C1 PTM3DL PTM3DH PTM3AL PTM3AH PTM3RPL PTM3RPH STM1C0 STM1C1 STM1DL STM1DH STM1AL STM1AH STM1RP STM�C0 STM�C1 STM�DL STM�DH STM�AL STM�AH STM�RP Se�to� 0 LVDC EEA Se�to� 1 EEC EED CP0C CP1C MFI0 MFI1 MFI� MFI3 MFI4 MFI5 MFI� MFI7 MFI8 MFI9 LCDC0 LCDC1 LCDC� SLEDC0 SLEDC1 SLEDC� SLEDC3 SLEDC4 FC0 FC1 FC� MDUWR0 MDUWR1 MDUWR� MDUWR3 MDUWR4 MDUWR5 MDUWCTRL CP0VOS CP1VOS PSC0R TB0C TB1C PSC1R SADOL SADOH SADC0 SADC1 SADC� SIMC0 SIMC1 SIMD SIMA/SIMC� SIMTOC SPIAC0 SPIAC1 SPIAD FARL FARH FD0L FD0H FD1L FD1H FD�L FD�H FD3L FD3H IFS0 IFS1 IFS� IFS3 IFS4 PAS0 PAS1 PBS0 PBS1 PCS0 PCS1 PDS0 PDS1 PES0 PES1 PFS0 PFS1 PGS0 PGS1 PHS0 PHS1 PJS0 PJS1 PTM4C0 PTM4C1 PTM4DL PTM4DH PTM4AL PTM4AH PTM4RPL PTM4RPH PTM5C0 PTM5C1 PTM5DL PTM5DH PTM5AL PTM5AH PTM5RPL PTM5RPH PTM�C0 PTM�C1 PTM�DL PTM�DH PTM�AL PTM�AH PTM�RPL PTM�RPH PTM7C0 PTM7C1 PTM7DL PTM7DH PTM7AL PTM7AH PTM7RPL PTM7RPH : Unused� �ead as 00H Special Purpose Data Memory Structure – HT67F2360 Rev. 1.00 70 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 00H 01H 0�H 03H 04H 05H 0�H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 1�H 13H 14H 15H 1�H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH �0H �1H ��H �3H �4H �5H ��H �7H �8H �9H �AH �BH �CH �DH �EH �FH 30H 31H 3�H 33H 34H 35H 3�H 37H 38H 39H 3AH 3BH 3CH 3DH 3EH 3FH Se�to� 0 IAR0 MP0 IAR1 MP1L MP1H ACC PCL TBLP TBLH TBHP STATUS PBP IAR� MP�L MP�H RSTFC INTC0 INTC1 INTC� INTC3 PA PAC PAPU PAWU PB PBC PBPU PC PCC PCPU PD PDC PDPU PE PEC PEPU PF PFC PFPU PG PGC PGPU PH PHC PHPU PJ PJC PJPU CRCCR CRCIN CRCDL CRCDH IECC RSTC VBGRC INTEG SCC HIRCC HXTC LXTC WDTC LVRC Se�to� 1 PTM0C0 PTM0C1 PTM0DL PTM0DH PTM0AL PTM0AH PTM0RPL PTM0RPH STM0C0 STM0C1 STM0DL STM0DH STM0AL STM0AH STM0RP Se�to� � U�SR U�CR1 U�CR� TXR_RXR� BRG� U0SR U0CR1 U0CR� TXR_RXR0 BRG0 U1SR U1CR1 U1CR� TXR_RXR1 BRG1 PTM1C0 PTM1C1 PTM1DL PTM1DH PTM1AL PTM1AH PTM1RPL PTM1RPH PTM�C0 PTM�C1 PTM�DL PTM�DH PTM�AL PTM�AH PTM�RPL PTM�RPH PTM3C0 PTM3C1 PTM3DL PTM3DH PTM3AL PTM3AH PTM3RPL PTM3RPH STM1C0 STM1C1 STM1DL STM1DH STM1AL STM1AH STM1RP STM�C0 STM�C1 STM�DL STM�DH STM�AL STM�AH STM�RP 40H 41H 4�H 43H 44H 45H 4�H 47H 48H 49H 4AH 4BH 4CH 4DH 4EH 4FH 50H 51H 5�H 53H 54H 55H 5�H 57H 58H 59H 5AH 5BH 5CH 5DH 5EH 5FH �0H �1H ��H �3H �4H �5H ��H �7H �8H �9H �AH �BH �CH �DH �EH �FH 70H 71H 7�H 73H 74H 75H 7�H 77H 78H 79H 7AH 7BH 7CH 7DH 7EH 7FH Se�to� 0 LVDC EEAL EEAH EED CP0C CP1C MFI0 MFI1 MFI� MFI3 MFI4 MFI5 MFI� MFI7 MFI8 MFI9 LCDC0 LCDC1 LCDC� SLEDC0 SLEDC1 SLEDC� SLEDC3 SLEDC4 MDUWR0 MDUWR1 MDUWR� MDUWR3 MDUWR4 MDUWR5 MDUWCTRL CP0VOS CP1VOS PSC0R TB0C TB1C PSC1R SADOL SADOH SADC0 SADC1 SADC� SIMC0 SIMC1 SIMD SIMA/SIMC� SIMTOC SPIAC0 SPIAC1 SPIAD FARL FARH FD0L FD0H FD1L FD1H FD�L FD�H FD3L FD3H Se�to� 1 EEC FC0 FC1 FC� IFS0 IFS1 IFS� IFS3 IFS4 PAS0 PAS1 PBS0 PBS1 PCS0 PCS1 PDS0 PDS1 PES0 PES1 PFS0 PFS1 PGS0 PGS1 PHS0 PHS1 PJS0 PJS1 PTM4C0 PTM4C1 PTM4DL PTM4DH PTM4AL PTM4AH PTM4RPL PTM4RPH PTM5C0 PTM5C1 PTM5DL PTM5DH PTM5AL PTM5AH PTM5RPL PTM5RPH PTM�C0 PTM�C1 PTM�DL PTM�DH PTM�AL PTM�AH PTM�RPL PTM�RPH PTM7C0 PTM7C1 PTM7DL PTM7DH PTM7AL PTM7AH PTM7RPL PTM7RPH : Unused� �ead as 00H Special Purpose Data Memory Structure – HT67F2370/HT67F2390 Rev. 1.00 71 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Special Function Register Description Most of the Special Function Register details will be described in the relevant functional section. However, several registers require a separate description in this section. Indirect Addressing Registers – IAR0, IAR1, IAR2 The Indirect Addressing Registers, IAR0, IAR1 and IAR2, although having their locations in normal RAM register space, do not actually physically exist as normal registers. The method of indirect addressing for RAM data manipulation uses these Indirect Addressing Registers and Memory Pointers, in contrast to direct memory addressing, where the actual memory address is specified. Actions on the IAR0, IAR1 and IAR2 registers will result in no actual read or write operation to these registers but rather to the memory location specified by their corresponding Memory Pointers, MP0, MP1L/MP1H or MP2L/MP2H. Acting as a pair, IAR0 and MP0 can together access data only from Sector 0 while the IAR1 register together with MP1L/MP1H register pair and IAR2 register together with MP2L/MP2H register pair can access data from any Data Memory sector. As the Indirect Addressing Registers are not physically implemented, reading the Indirect Addressing Registers indirectly will return a result of "00H" and writing to the registers indirectly will result in no operation. Memory Pointers – MP0, MP1H/MP1L, MP2H/MP2L Five Memory Pointers, known as MP0, MP1L, MP1H, MP2L and MP2H, are provided. These Memory Pointers are physically implemented in the Data Memory and can be manipulated in the same way as normal registers providing a convenient way with which to address and track data. When any operation to the relevant Indirect Addressing Registers is carried out, the actual address that the microcontroller is directed to is the address specified by the related Memory Pointer. MP0, together with Indirect Addressing Register, IAR0, are used to access data from Sector 0, while MP1L/MP1H together with IAR1 and MP2L/MP2H together with IAR2 are used to access data from all data sectors according to the corresponding MP1H or MP2H register. Direct Addressing can be used in all data sectors using the corresponding instruction which can address all available data memory space. Indirect Addressing Program Example • Example 1 data .section ‘data’ adres1 db ? adres2 db ? adres3 db ? adres4 db ? block db ? code .section at 0 code org 00h start: mov a,04h; mov block,a mov a,offset adres1 ; mov mp0,a ; loop: clr IAR0 ; inc mp0; sdz block ; jmp loop continue: Rev. 1.00 setup size of block Accumulator loaded with first RAM address setup memory pointer with first RAM address clear the data at address defined by MP0 increment memory pointer check if last memory location has been cleared 72 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • Example 2 data .section ‘data’ adres1 db ? adres2 db ? adres3 db ? adres4 db ? block db ? code .section at 0 ‘code’ org 00h start: mov a,04h ; setup size of block mov block,a mov a,01h ; setup the memory sector mov mp1h,a mov a,offset adres1 ; Accumulator loaded with first RAM address mov mp1l,a ; setup memory pointer with first RAM address loop: clr IAR1 ; clear the data at address defined by MP1L inc mp1l ; increment memory pointer MP1L sdz block ; check if last memory location has been cleared jmp loop continue: : The important point to note here is that in the example shown above, no reference is made to specific RAM addresses. Direct Addressing Program Example using extended instructions data .section ‘data’ temp db ? code .section at 0 code org 00h start: lmov a,[m]; move [m] data to acc lsub a, [m+1] ; compare [m] and [m+1] data snz c; [m]>[m+1]? jmp continue; no lmov a,[m] ; yes, exchange [m] and [m+1] data mov temp,a lmov a,[m+1] lmov [m],a mov a,temp lmov [m+1],a continue: : Note: Here "m" is a data memory address located in any data memory sectors. For example, m=1F0H, it indicates address 0F0H in Sector 1. Rev. 1.00 73 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Program Memory Bank Pointer – PBP For the series of devices the Program Memory is divided into several banks except for the HT67F2350 device. Selecting the required Program Memory area is achieved using the Program Memory Bank Pointer, PBP. The PBP register should be properly configured before the device executes the "Branch" operation using the "JMP" or "CALL" instruction. After that a jump to a nonconsecutive Program Memory address which is located in a certain bank selected by the program memory bank pointer bits will occur. PBP Register – HT67F2360 Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 PBP0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~1 D7~D1: General data bits and can be read or written. Bit 0 PBP0: Program Memory Bank Point bit 0 0: Bank 0 1: Bank 1 PBP Register – HT67F2370 Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 PBP1 PBP0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~2 D7~D2: General data bits and can be read or written. Bit 1~0 PBP1~PBP0: Program Memory Bank Point bit 1 ~ bit 0 00: Bank 0 01: Bank 1 10: Bank 2 11: Bank 3 PBP Register – HT67F2390 Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 PBP2 PBP1 PBP0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~3 D7~D3: General data bits and can be read or written. Bit 2~0 PBP2~PBP0: Program Memory Bank Point bit 2 ~ bit 0 000: Bank 0 001: Bank 1 010: Bank 2 011: Bank 3 100: Bank 4 101: Bank 5 110: Bank 6 111: Bank 7 74 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Accumulator – ACC The Accumulator is central to the operation of any microcontroller and is closely related with operations carried out by the ALU. The Accumulator is the place where all intermediate results from the ALU are stored. Without the Accumulator it would be necessary to write the result of each calculation or logical operation such as addition, subtraction, shift, etc., to the Data Memory resulting in higher programming and timing overheads. Data transfer operations usually involve the temporary storage function of the Accumulator; for example, when transferring data between one user-defined register and another, it is necessary to do this by passing the data through the Accumulator as no direct transfer between two registers is permitted. Program Counter Low Register – PCL To provide additional program control functions, the low byte of the Program Counter is made accessible to programmers by locating it within the Special Purpose area of the Data Memory. By manipulating this register, direct jumps to other program locations are easily implemented. Loading a value directly into this PCL register will cause a jump to the specified Program Memory location; however, as the register is only 8-bit wide, only jumps within the current Program Memory page are permitted. When such operations are used, note that a dummy cycle will be inserted. Look-up Table Registers – TBLP, TBHP, TBLH These three special function registers are used to control operation of the look-up table which is stored in the Program Memory. The TBLP and TBHP registers are the table pointer pair and indicates the location where the table data is located. Their value must be setup before any table read instructions are executed. Their value can be changed, for example using the "INC" or "DEC" instructions, allowing for easy table data pointing and reading. TBLH is the location where the high order byte of the table data is stored after a table read data instruction has been executed. Note that the lower order table data byte is transferred to a user defined location. Status Register – STATUS This 8-bit register contains the zero flag (Z), carry flag (C), auxiliary carry flag (AC), overflow flag (OV), SC flag, CZ flag, power down flag (PDF), and watchdog time-out flag (TO). These arithmetic/ logical operation and system management flags are used to record the status and operation of the microcontroller. With the exception of the TO and PDF flags, bits in the status register can be altered by instructions like most other registers. Any data written into the status register will not change the TO or PDF flag. In addition, operations related to the status register may give different results due to the different instruction operations. The TO flag can be affected only by a system power-up, a WDT time-out or by executing the "CLR WDT" or "HALT" instruction. The PDF flag is affected only by executing the "HALT" or "CLR WDT" instruction or during a system power-up. The Z, OV, AC, C, SC and CZ flags generally reflect the status of the latest operations. • C is set if an operation results in a carry during an addition operation or if a borrow does not take place during a subtraction operation; otherwise C is cleared. C is also affected by a rotate through carry instruction. • AC is set if an operation results in a carry out of the low nibbles in addition, or no borrow from the high nibble into the low nibble in subtraction; otherwise AC is cleared. • Z is set if the result of an arithmetic or logical operation is zero; otherwise Z is cleared. • OV is set if an operation results in a carry into the highest-order bit but not a carry out of the highest-order bit, or vice versa; otherwise OV is cleared. Rev. 1.00 75 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • PDF is cleared by a system power-up or executing the "CLR WDT" instruction. PDF is set by executing the "HALT" instruction. • TO is cleared by a system power-up or executing the "CLR WDT" or "HALT" instruction. TO is set by a WDT time-out. • SC is the result of the "XOR" operation which is performed by the OV flag and the MSB of the current instruction operation result. • CZ is the operational result of different flags for different instructions. Refer to register definitions for more details. In addition, on entering an interrupt sequence or executing a subroutine call, the status register will not be pushed onto the stack automatically. If the contents of the status registers are important and if the subroutine can corrupt the status register, precautions must be taken to correctly save it. STATUS Register Bit 7 6 5 4 3 2 1 0 Name SC CZ TO PDF OV Z AC C R/W R R R R R/W R/W R/W R/W POR x x 0 0 x x x x "x": unknown Rev. 1.00 Bit 7 SC: The result of the "XOR" operation which is performed by the OV flag and the MSB of the instruction operation result. Bit 6 CZ: The operational result of different flags for different instructions. For SUB/SUBM/LSUB/LSUBM instructions, the CZ flag is equal to the Z flag. For SBC/ SBCM/ LSBC/ LSBCM instructions, the CZ flag is the "AND" operation result which is performed by the previous operation CZ flag and current operation zero flag. For other instructions, the CZ flag will not be affected. Bit 5 TO: Watchdog Time-out flag 0: After power up or executing the "CLR WDT" or "HALT" instruction 1: A watchdog time-out occurred Bit 4 PDF: Power down flag 0: After power up or executing the "CLR WDT" instruction 1: By executing the "HALT" instruction Bit 3 OV: Overflow flag 0: No overflow 1: An operation results in a carry into the highest-order bit but not a carry out of the highest-order bit or vice versa Bit 2 Z: Zero flag 0: The result of an arithmetic or logical operation is not zero 1: The result of an arithmetic or logical operation is zero Bit 1 AC: Auxiliary flag 0: No auxiliary carry 1: An operation results in a carry out of the low nibbles, in addition, or no borrow from the high nibble into the low nibble in subtraction Bit 0 C: Carry flag 0: No carry-out 1: An operation results in a carry during an addition operation or if a borrow does not take place during a subtraction operation The "C" flag is also affected by a rotate through carry instruction. 76 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM EEPROM Data Memory These devices contain an area of internal EEPROM Data Memory. EEPROM, which stands for Electrically Erasable Programmable Read Only Memory, is by its nature a non-volatile form of re-programmable memory, with data retention even when its power supply is removed. By incorporating this kind of data memory, a whole new host of application possibilities are made available to the designer. The availability of EEPROM storage allows information such as product identification numbers, calibration values, specific user data, system setup data or other product information to be stored directly within the product microcontroller. The process of reading and writing data to the EEPROM memory has been reduced to a very trivial affair. Device Capacity Address 256 × 8 00H ~ FFH HT67F2370 512 × 8 000H ~ 1FFH HT67F2390 1024 × 8 000H ~ 3FFH HT67F2350 HT67F2360 EEPROM Data Memory Structure The EEPROM Data Memory capacity is up to 1024×8 bits for the series of devices. Unlike the Program Memory and RAM Data Memory, the EEPROM Data Memory is not directly mapped into memory space and is therefore not directly addressable in the same way as the other types of memory. Read and Write operations to the EEPROM are carried out in single byte operations using an address and data register in sector 0 and a single control register in sector 1. EEPROM Registers Three registers control the overall operation of the internal EEPROM Data Memory. These are the address register, EEA, the data register, EED and a single control register, EEC. As both the EEA and EED registers are located in sector 0, they can be directly accessed in the same was as any other Special Function Register. The EEC register, however, being located in sector 1, can be read from or written to indirectly using the MP1H/MP1L or MP2H/MP2L Memory Pointer pair and Indirect Addressing Register, IAR1 or IAR2. Because the EEC control register is located at address 40H in sector 1, the Memory Pointer low byte register, MP1L or MP2L, must first be set to the value 40H and the Memory Pointer high byte register, MP1H or MP2H, set to the value, 01H, before any operations on the EEC register are executed. Register Name Bit 7 6 5 4 3 2 1 0 EEA (HT67F2350/60) EEA7 EEA6 EEA5 EEA4 EEA3 EEA2 EEA1 EEA0 EEAL (HT76F2370/90) EEAL7 EEAL6 EEAL5 EEAL4 EEAL3 EEAL2 EEAL1 EEAL0 EEAH (HT67F2370) — — — — — — — EEAH0 EEAH (HT67F2390) — — — — — — EEAH1 EEAH0 EED D7 D6 D5 D4 D3 D2 D1 D0 EEC — — — — WREN WR RDEN RD EEPROM Registers List Rev. 1.00 77 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM EEA Register – HT67F2350/HT67F2360 Bit 7 6 5 4 3 2 1 0 Name EEA7 EEA6 EEA5 EEA4 EEA3 EEA2 EEA1 EEA0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 EEA7~EEA0: Data EEPROM address bit 7 ~ bit0 EEAL Register – HT67F2370/HT67F2390 Bit 7 6 5 4 3 2 1 0 Name EEAL7 EEAL6 EEAL5 EEAL4 EEAL3 EEAL2 EEAL1 EEAL0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 EEAL7~EEAL0: Data EEPROM low byte address bit 7 ~ bit 0 EEAH Register – HT67F2370 Bit 7 6 5 4 3 2 1 0 Name — — — — — — — EEAH0 R/W — — — — — — — R/W POR — — — — — — — 0 2 1 0 Bit 7~1 Unimplemented, read as "0" Bit 0 EEAH0: Data EEPROM high byte address bit 0 EEAH Register – HT67F2390 Bit 7 6 5 4 3 Name — — — — — — EEAH1 EEAH0 R/W — — — — — — R/W R/W POR — — — — — — 0 0 Bit 7~2 Unimplemented, read as "0" Bit 1~0 EEAH1~EEAH0: Data EEPROM high byte address bit 1 ~ bit 0 EED Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Rev. 1.00 D7~D0: Data EEPROM data bit 7 ~ bit 0 78 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM EEC Register Bit 7 6 5 4 3 2 1 0 Name — — — — WREN WR RDEN RD R/W — — — — R/W R/W R/W R/W POR — — — — 0 0 0 0 Bit 7~4 Unimplemented, read as "0" Bit 3 WREN: Data EEPROM write enable 0: Disable 1: Enable This is the Data EEPROM Write Enable Bit which must be set high before Data EEPROM write operations are carried out. Clearing this bit to zero will inhibit Data EEPROM write operations. Note that the WREN bit will automatically be cleared to zero after the write operation is finished. Bit 2 WR: EEPROM write control 0: Write cycle has finished 1: Activate a write cycle This is the Data EEPROM Write Control Bit and when set high by the application program will activate a write cycle. This bit will be automatically reset to zero by the hardware after the write cycle has finished. Setting this bit high will have no effect if the WREN has not first been set high. Bit 1 RDEN: Data EEPROM read enable 0: Disable 1: Enable This is the Data EEPROM Read Enable Bit which must be set high before Data EEPROM read operations are carried out. Clearing this bit to zero will inhibit Data EEPROM read operations. Bit 0 RD: EEPROM read control 0: Read cycle has finished 1: Activate a read cycle This is the Data EEPROM Read Control Bit and when set high by the application program will activate a read cycle. This bit will be automatically reset to zero by the hardware after the read cycle has finished. Setting this bit high will have no effect if the RDEN has not first been set high. Note: The WREN, WR, RDEN and RD can not be set to "1" at the same time in one instruction. The WR and RD can not be set to "1" at the same time. Reading Data from the EEPROM To read data from the EEPROM, the EEPROM address of the data to be read must first be placed in the EEA register or EEAL/EEAH register pair. Then the read enable bit, RDEN, in the EEC register must be set high to enable the read function. If the RD bit in the EEC register is now set high, a read cycle will be initiated. Setting the RD bit high will not initiate a read operation if the RDEN bit has not been set. When the read cycle terminates, the RD bit will be automatically cleared to zero, after which the data can be read from the EED register. The data will remain in the EED register until another read or write operation is executed. The application program can poll the RD bit to determine when the data is valid for reading. Rev. 1.00 79 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Writing Data to the EEPROM To write data to the EEPROM, the EEPROM address of the data to be written must first be placed in the EEA register or EEAL/EEAH register pair and the data placed in the EED register. To initiate a write cycle the write enable bit, WREN, in the EEC register must first be set high to enable the write function. After this, the WR bit in the EEC register must be immediately set high to initiate a write cycle successfully. These two instructions must be executed consecutively. The global interrupt bit EMI should also first be cleared before implementing any write operations, and then set high again after the write cycle has started. Note that setting the WR bit high will not initiate a write cycle if the WREN bit has not been set. As the EEPROM write cycle is controlled using an internal timer whose operation is asynchronous to microcontroller system clock, a certain time will elapse before the data will have been written into the EEPROM. Detecting when the write cycle has finished can be implemented either by polling the WR bit in the EEC register or by using the EEPROM interrupt. When the write cycle terminates, the WR bit will be automatically cleared to zero by the microcontroller, informing the user that the data has been written to the EEPROM. The application program can therefore poll the WR bit to determine when the write cycle has ended. Write Protection Protection against inadvertent write operation is provided in several ways. After the device is powered on, the Write Enable bit in the control register will be cleared preventing any write operations. Also at power-on the Memory Pointer high byte register, MP1H or MP2H, will be reset to zero, which means that Data Memory sector 0 will be selected. As the EEPROM control register is located in sector 1, this adds a further measure of protection against spurious write operations. During normal program operation, ensuring that the Write Enable bit in the control register is cleared will safeguard against incorrect write operations. EEPROM Interrupt The EEPROM write interrupt is generated when an EEPROM write cycle has ended. The EEPROM interrupt must first be enabled by setting the DEE bit in the relevant interrupt register. However, as the EEPROM is contained within a Multi-function Interrupt, the associated multi-function interrupt enable bit must also be set. When an EEPROM write cycle ends, the DEF request flag and its associated multi-function interrupt request flag will both be set. If the global, EEPROM and Multifunction interrupts are enabled and the stack is not full, a jump to the associated Multi-function Interrupt vector will take place. When the interrupt is serviced only the Multi-function interrupt flag will be automatically reset, the EEPROM interrupt flag must be manually reset by the application program. Rev. 1.00 80 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Programming Considerations Care must be taken that data is not inadvertently written to the EEPROM. Protection can be Periodic by ensuring that the Write Enable bit is normally cleared to zero when not writing. Also the Memory Pointer high byte register could be normally cleared to zero as this would inhibit access to sector 1 where the EEPROM control register exist. Although certainly not necessary, consideration might be given in the application program to the checking of the validity of new write data by a simple read back process. When writing data the WR bit must be set high immediately after the WREN bit has been set high, to ensure the write cycle executes correctly. The global interrupt bit EMI should also be cleared before a write cycle is executed and then re-enabled after the write cycle starts. Note that the device should not enter the IDLE or SLEEP mode until the EEPROM read or write operation is totally complete. Otherwise, the EEPROM read or write operation will fail. Programming Example – for HT67F2350 • Reading data from the EEPROM – polling method MOV A, EEPROM_ADRES MOV EEA, A MOV A, 040H MOV MP1L, A MOV A, 01H MOV MP1H, A SET IAR1.1 SET IAR1.0 BACK: SZ IAR1.0 JMP BACK CLR IAR1 CLR MP1H MOV A, EED MOV READ_DATA, A ; user defined address ; setup memory pointer low byte MP1L ; MP1L points to EEC register ; setup Memory Pointer high byte MP1H ; set RDEN bit, enable read operations ; start Read Cycle - set RD bit ; check for read cycle end ; disable EEPROM write ; move read data to register • Writing Data to the EEPROM – polling method MOV A, EEPROM_ADRES MOV EEA, A MOV A, EEPROM_DATA MOV EED, A MOV A, 040H MOV MP1L, A MOV A, 01H MOV MP1H, A CLR EMI SET IAR1.3 SET IAR1.2 SET EMI BACK: SZ IAR1.2 JMP BACK CLR IAR1 CLR MP1H Rev. 1.00 ; user defined address ; user defined data ; setup memory pointer low byte MP1L ; MP1L points to EEC register ; setup Memory Pointer high byte MP1H ; set WREN bit, enable write operations ; start Write Cycle - set WR bit ; check for write cycle end ; disable EEPROM write 81 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Oscillators Various oscillator types offer the user a wide range of functions according to their various application requirements. The flexible features of the oscillator functions ensure that the best optimisation can be achieved in terms of speed and power saving. Oscillator selections and operation are selected through a combination of application program and relevant control registers. Oscillator Overview In addition to being the source of the main system clock the oscillators also provide clock sources for the Watchdog Timer and Time Base Interrupts. External oscillators requiring some external components as well as fully integrated internal oscillators, requiring no external components, are provided to form a wide range of both fast and slow system oscillators. All oscillator options are selected through register programming. The higher frequency oscillators provide higher performance but carry with it the disadvantage of higher power requirements, while the opposite is of course true for the lower frequency oscillators. With the capability of dynamically switching between fast and slow system clock, the device has the flexibility to optimize the performance/power ratio, a feature especially important in power sensitive portable applications. Type Name Frequency Pins External High Speed Crystal HXT 400 kHz~16 MHz OSC1/OSC2 Internal High Speed RC HIRC 8/12/16 MHz — External Low Speed Crystal LXT 32.768 kHz XT1/XT2 Internal Low Speed RC LIRC 32 kHz — Oscillator Types System Clock Configurations There are four methods of generating the system clock, two high speed oscillators and two low speed oscillators for all devices. The high speed oscillator is the external crystal/ceramic oscillator, HXT, and the internal 8/12/16 MHz RC oscillator, HIRC. The two low speed oscillators are the internal 32 kHz RC oscillator, LIRC, and the external 32.768 kHz crystal oscillator, LXT. Selecting whether the low or high speed oscillator is used as the system oscillator is implemented using the CKS2~CKS0 bits in the SCC register and as the system clock can be dynamically selected. The actual source clock used for the low speed oscillators is chosen via the FSS bit in the SCC register while for the high speed oscillator the source clock is selected by the FHS bit in the SCC register. The frequency of the slow speed or high speed system clock is determined using the CKS2~CKS0 bits in the SCC register. Note that two oscillator selections must be made namely one high speed and one low speed system oscillators. It is not possible to choose a no-oscillator selection for either the high or low speed oscillator. Rev. 1.00 82 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM fH High Speed Os�ollato�s HIRCEN HXTEN FHS fH/� fH/4 HIRC fH/8 P�es�ale� fH HXT fSYS fH/1� fH/3� fH/�4 Low Speed Os�ollato�s FSS CKS�~CKS0 LXTEN LXT fSUB fSUB fLIRC LIRC fLIRC System Clock Configurations External Crystal/Ceramic Oscillator – HXT The External Crystal/Ceramic System Oscillator is the high frequency oscillator, which is the default oscillator clock source after power on. For most crystal oscillator configurations, the simple connection of a crystal across OSC1 and OSC2 will create the necessary phase shift and feedback for oscillation, without requiring external capacitors. However, for some crystal types and frequencies, to ensure oscillation, it may be necessary to add two small value capacitors, C1 and C2. Using a ceramic resonator will usually require two small value capacitors, C1 and C2, to be connected as shown for oscillation to occur. The values of C1 and C2 should be selected in consultation with the crystal or resonator manufacturer’s specification. For oscillator stability and to minimise the effects of noise and crosstalk, it is important to ensure that the crystal and any associated resistors and capacitors along with interconnecting lines are all located as close to the MCU as possible. C1 Internal Oscillator Circuit OSC1 RP RF OSC� C� To inte�nal �i��uits Note: 1. RP is no��ally not �equi�ed. C1 and C� a�e �equi�ed. �. Although not shown OSC1/OSC� pins have a pa�asiti� �apa�itan�e of a�ound 7pF. Crystal/Resonator Oscillator HXT Oscillator C1 and C2 Values Crystal Frequency C1 C2 12MHz 0 pF 0 pF 8MHz 0 pF 0 pF 4MHz 0 pF 0 pF 1MHz 100 pF 100 pF Note: C1 and C2 values are for guidance only. Crystal Recommended Capacitor Values Rev. 1.00 83 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Internal High Speed RC Oscillator – HIRC The internal RC oscillator is a fully integrated system oscillator requiring no external components. The internal RC oscillator has a fixed frequency of 8/12/16 MHz. Device trimming during the manufacturing process and the inclusion of internal frequency compensation circuits are used to ensure that the influence of the power supply voltage, temperature and process variations on the oscillation frequency are minimised. As a result, at a power supply of 3V or 5V and at a temperature of 25°C degrees, the selected trimmed oscillation frequency will have a tolerance within 1%. Note that if this internal system clock is selected, as it requires no external pins for its operation, I/O pins are free for use as normal I/O pins or other pin-shared functional pins. External 32.768 kHz Crystal Oscillator – LXT The External 32.768 kHz Crystal System Oscillator is one of the low frequency oscillator choices, which is selected via a software control bit, FSS. This clock source has a fixed frequency of 32.768 kHz and requires a 32.768 kHz crystal to be connected between pins XT1 and XT2. The external resistor and capacitor components connected to the 32.768 kHz crystal are necessary to provide oscillation. For applications where precise frequencies are essential, these components may be required to provide frequency compensation due to different crystal manufacturing tolerances. After the LXT oscillator is enabled by setting the LXTEN bit to 1, there is a time delay associated with the LXT oscillator waiting for it to start-up. When the microcontroller enters the SLEEP or IDLE Mode, the system clock is switched off to stop microcontroller activity and to conserve power. However, in many microcontroller applications it may be necessary to keep the internal timers operational even when the microcontroller is in the SLEEP or IDLE Mode. To do this, another clock, independent of the system clock, must be provided. However, for some crystals, to ensure oscillation and accurate frequency generation, it is necessary to add two small value external capacitors, C1 and C2. The exact values of C1 and C2 should be selected in consultation with the crystal or resonator manufacturer’s specification. The external parallel feedback resistor, Rp, is required. The pin-shared software control bits determine if the XT1/XT2 pins are used for the LXT oscillator or as I/O or other pin-shared functional pins. • If the LXT oscillator is not used for any clock source, the XT1/XT2 pins can be used as normal I/O or other pin-shared functional pins. • If the LXT oscillator is used for any clock source, the 32.768 kHz crystal should be connected to the XT1/XT2 pins. For oscillator stability and to minimise the effects of noise and crosstalk, it is important to ensure that the crystal and any associated resistors and capacitors along with interconnecting lines are all located as close to the MCU as possible. C1 3�.7�8kHz XT1 Inte�nal RC Os�illato� RP XT� C� Internal Oscillator Circuit To inte�nal �i��uits Note: 1. RP� C1 and C� a�e �equi�ed. �. Although not shown pins have a pa�asiti� �apa�itan�e of a�ound 7pF. External LXT Oscillator Rev. 1.00 84 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Internal 32kHz Oscillator – LIRC The Internal 32 kHz System Oscillator is one of the low frequency oscillator choices, which is selected via a software control bit, FSS. It is a fully integrated RC oscillator with a typical frequency of 32 kHz at 5V, requiring no external components for its implementation. Device trimming during the manufacturing process and the inclusion of internal frequency compensation circuits are used to ensure that the influence of the power supply voltage, temperature and process variations on the oscillation frequency are minimised. As a result, at a power supply of 5V and at a temperature of 25˚C degrees, the fixed oscillation frequency of 32 kHz will have a tolerance within 5%. Operating Modes and System Clocks Present day applications require that their microcontrollers have high performance but often still demand that they consume as little power as possible, conflicting requirements that are especially true in battery powered portable applications. The fast clocks required for high performance will by their nature increase current consumption and of course vice-versa lower speed clocks reduce current consumption. As Holtek has provided these devices with both high and low speed clock sources and the means to switch between them dynamically, the user can optimise the operation of their microcontroller to achieve the best performance/power ratio. System Clocks Each device has different clock sources for both the CPU and peripheral function operation. By providing the user with a wide range of clock selections using register programming, a clock system can be configured to obtain maximum application performance. The main system clock, can come from either a high frequency, fH, or low frequency, fSUB, source, and is selected using the CKS2~CKS0 bits in the SCC register. The high speed system clock is sourced from an HXT or HIRC oscillator, selected via configuring the FHS bit in the SCC register. The low speed system clock source can be sourced from the internal clock fSUB. If fSUB is selected then it can be sourced by either the LXT or LIRC oscillators, selected via configuring the FSS bit in the SCC register. The other choice, which is a divided version of the high speed system oscillator has a range of fH/2~fH/64. Rev. 1.00 85 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM fH High Speed Os�ollato�s HIRCEN HXTEN FHS fH/� fH/4 HIRC fH/8 P�es�ale� fH HXT fSYS fH/1� fH/3� fH/�4 FSS LXTEN CKS�~CKS0 LXT fSUB LIRC fSUB fLIRC fSYS fPSC0 fSYS/4 Low Speed Os�ollato�s fSUB P�es�ale� 0 Ti�e Base 0 TB0[�:0] CLKSEL0[1:0] fSYS fPSC1 fSYS/4 fSUB CLKSEL1[1:0] fLIRC fLIRC P�es�ale� 1 Ti�e Base 1 TB1[�:0] WDT LVR Device Clock Configurations Note: When the system clock source fSYS is switched to fSUB from fH, the high speed oscillation can be stopped to conserve the power or continue to oscillate to provide the clock source, fH~fH/64, for peripheral circuit to use, which is determined by configuring the corresponding high speed oscillator enable control bit. Rev. 1.00 86 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM System Operation Modes There are six different modes of operation for the microcontroller, each one with its own special characteristics and which can be chosen according to the specific performance and power requirements of the application. There are two modes allowing normal operation of the microcontroller, the FAST Mode and SLOW Mode. The remaining four modes, the SLEEP, IDLE0, IDLE1 and IDLE2 Mode are used when the microcontroller CPU is switched off to conserve power. Operation Mode CPU FAST On SLOW On Register Setting FHIDEN FSIDEN CKS2~CKS0 x x 000~110 x x IDLE0 Off 0 1 IDLE1 Off 1 1 IDLE2 Off 1 0 SLEEP Off 0 0 fSYS fH fH~fH/64 On 111 fSUB 000~110 Off 111 On xxx On 000~110 On 111 Off xxx Off fSUB fLIRC On On On On Off On On On On On On Off On Off Off On/Off (1) On (2) Note: 1. The fH clock will be switched on or off by configuring the corresponding oscillator enable bit in the SLOW mode. 2. The fLIRC clock will be switched on if the WDT function is enabled. FAST Mode As the name suggests this is one of the main operating modes where the microcontroller has all of its functions operational and where the system clock is provided by one of the high speed oscillators. This mode operates allowing the microcontroller to operate normally with a clock source will come from one of the high speed oscillators, either the HXT or HIRC oscillators. The high speed oscillator will however first be divided by a ratio ranging from 1 to 64, the actual ratio being selected by the CKS2~CKS0 bits in the SCC register. Although a high speed oscillator is used, running the microcontroller at a divided clock ratio reduces the operating current. SLOW Mode This is also a mode where the microcontroller operates normally although now with a slower speed clock source. The clock source used will be from fSUB. The fSUB clock is derived from either the LIRC or LXT oscillator. SLEEP Mode The SLEEP Mode is entered when an HALT instruction is executed and when the FHIDEN and FSIDEN bit are low. In the SLEEP mode the CPU will be stopped and both the high and low speed oscillators will be switched off. However the fLIRC clock will continue to operate if the WDT function is enabled by the WDTC register. IDLE0 Mode The IDLE0 Mode is entered when an HALT instruction is executed and when the FHIDEN bit in the SCC register is low and the FSIDEN bit in the SCC register is high. In the IDLE0 Mode the CPU will be switched off but the low speed oscillator will be turned on to drive some peripheral functions. Rev. 1.00 87 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM IDLE1 Mode The IDLE1 Mode is entered when an HALT instruction is executed and when the FHIDEN bit in the SCC register is high and the FSIDEN bit in the SCC register is high. In the IDLE1 Mode the CPU will be switched off but both the high and low speed oscillators will be turned on to provide a clock source to keep some peripheral functions operational. IDLE2 Mode The IDLE2 Mode is entered when an HALT instruction is executed and when the FHIDEN bit in the SCC register is high and the FSIDEN bit in the SCC register is low. In the IDLE2 Mode the CPU and low speed oscillator will be switched off but the high speed oscillator will be turned on to provide a clock source to keep some peripheral functions operational. Control Registers The registers, SCC, HIRCC, HXTC and LXTC, are used to control the system clock and the corresponding oscillator configurations. Bit Register Name 7 6 5 4 3 2 1 0 SCC CKS2 CKS1 CKS0 — FHS FSS FHIDEN FSIDEN HIRCC — — — — HIRC1 HIRC0 HIRCF HIRCEN HXTC — — — — — HXTM HXTF HXTEN LXTC — — — — — — LXTF LXTEN System Operating Mode Control Registers List SCC Register Bit 7 6 5 4 3 2 1 0 Name CKS2 CKS1 CKS0 — FHS FSS FHIDEN FSIDEN R/W R/W R/W R/W — R/W R/W R/W R/W POR 0 0 0 — 0 0 0 0 Bit 7~5 Rev. 1.00 CKS2~CKS0: System clock selection 000: fH 001: fH/2 010: fH/4 011: fH/8 100: fH/16 101: fH/32 110: fH/64 111: fSUB These three bits are used to select which clock is used as the system clock source. In addition to the system clock source directly derived from fH or fSUB, a divided version of the high speed system oscillator can also be chosen as the system clock source. Bit 4 Unimplemented, read as "0" Bit 3 FHS: High Frequency clock selection 0: HIRC 1: HXT Bit 2 FSS: Low Frequency clock selection 0: LIRC 1: LXT 88 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 1 FHIDEN: High Frequency oscillator control when CPU is switched off 0: Disable 1: Enable This bit is used to control whether the high speed oscillator is activated or stopped when the CPU is switched off by executing an "HALT" instruction. Bit 0 FSIDEN: Low Frequency oscillator control when CPU is switched off 0: Disable 1: Enable This bit is used to control whether the low speed oscillator is activated or stopped when the CPU is switched off by executing an "HALT" instruction. The LIRC oscillator is controlled by this bit together with the WDT function enable control when the LIRC is selected to be the low speed oscillator clock source or the WDT function is enabled respectively. If this bit is cleared to 0 but the WDT function is enabled, the LIRC oscillator will also be enabled. HIRCC Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — — — — HIRC1 HIRC0 HIRCF HIRCEN R/W — — — — R/W R/W R R/W POR — — — — 0 0 0 1 Bit 7~4 Unimplemented, read as "0" Bit 3~2 HIRC1~HIRC0: HIRC frequency selection 00: 8 MHz 01: 12 MHz 10: 16 MHz 11: 8 MHz When the HIRC oscillator is enabled or the HIRC frequency selection is changed by the application program, the clock frequency will automatically be changed after the HIRCF flag is set to 1. Bit 1 HIRCF: HIRC oscillator stable flag 0: HIRC unstable 1: HIRC stable This bit is used to indicate whether the HIRC oscillator is stable or not. When the HIRCEN bit is set to 1 to enable the HIRC oscillator or the HIRC frequency selection is changed by the application program, the HIRCF bit will first be cleared to 0 and then set to 1 after the HIRC oscillator is stable. Bit 0 HIRCEN: HIRC oscillator enable control 0: Disable 1: Enable 89 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM HXTC Register Bit 7 6 5 4 3 2 1 0 Name — — — — — HXTM HXTF HXTEN R/W — — — — — R/W R R/W POR — — — — — 0 0 0 Bit 7~3 Unimplemented, read as "0" Bit 2 HXTM: HXT mode selection 0: HXT frequency ≤ 10 MHz 1: HXT frequency > 10 MHz This bit is used to select the HXT oscillator operating mode. Note that this bit must be properly configured before the HXT is enabled. When the OSC1 and OSC2 pins are enabled and the HXTEN bit is set to 1 to enable the HXT oscillator, it is invalid to change the value of this bit. Otherwise, this bit value can be changed with no operation on the HXT function. Bit 1 HXTF: HXT oscillator stable flag 0: HXT unstable 1: HXT stable This bit is used to indicate whether the HXT oscillator is stable or not. When the HXTEN bit is set to 1 to enable the HXT oscillator, the HXTF bit will first be cleared to 0 and then set to 1 after the HXT oscillator is stable. Bit 0 HXTEN: HXT oscillator enable control 0: Disable 1: Enable LXTC Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — — — — — — LXTF LXTEN R/W — — — — — — R R/W POR — — — — — — 0 0 Bit 7~2 Unimplemented, read as "0" Bit 1 LXTF: LXT oscillator stable flag 0: LXT unstable 1: LXT stable This bit is used to indicate whether the LXT oscillator is stable or not. When the LXTEN bit is set to 1 to enable the LXT oscillator, the LXTF bit will first be cleared to 0 and then set to 1 after the LXT oscillator is stable. Bit 0 LXTEN: LXT oscillator enable control 0: Disable 1: Enable 90 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Operating Mode Switching These devices can switch between operating modes dynamically allowing the user to select the best performance/power ratio for the present task in hand. In this way microcontroller operations that do not require high performance can be executed using slower clocks thus requiring less operating current and prolonging battery life in portable applications. In simple terms, Mode Switching between the FAST Mode and SLOW Mode is executed using the CKS2~CKS0 bits in the SCC register while Mode Switching from the FAST/SLOW Modes to the SLEEP/IDLE Modes is executed via the HALT instruction. When an HALT instruction is executed, whether the device enters the IDLE Mode or the SLEEP Mode is determined by the condition of the FHIDEN and FSIDEN bits in the SCC register. FAST fSYS=fH~fH/64 fH on CPU run fSYS on fSUB on SLOW fSYS=fSUB fSUB on CPU run fSYS on fH on/off SLEEP HALT instruction executed CPU stop FHIDEN=0 FSIDEN=0 fH off fSUB off IDLE0 HALT instruction executed CPU stop FHIDEN=0 FSIDEN=1 fH off fSUB on IDLE2 HALT instruction executed CPU stop FHIDEN=1 FSIDEN=0 fH on fSUB off Rev. 1.00 91 IDLE1 HALT instruction executed CPU stop FHIDEN=1 FSIDEN=1 fH on fSUB on December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM FAST Mode to SLOW Mode Switching When running in the FAST Mode, which uses the high speed system oscillator, and therefore consumes more power, the system clock can switch to run in the SLOW Mode by set the CKS2~CKS0 bits to "111" in the SCC register. This will then use the low speed system oscillator which will consume less power. Users may decide to do this for certain operations which do not require high performance and can subsequently reduce power consumption. The SLOW Mode is sourced from the LXT or LIRC oscillator determined by the FSS bit in the SCC register and therefore requires this oscillator to be stable before full mode switching occurs. FAST Mode CKS2~CKS0 = 111 SLOW Mode FHIDEN=0, FSIDEN=0 HALT instruction is executed SLEEP Mode FHIDEN=0, FSIDEN=1 HALT instruction is executed IDLE0 Mode FHIDEN=1, FSIDEN=1 HALT instruction is executed IDLE1 Mode FHIDEN=1, FSIDEN=0 HALT instruction is executed IDLE2 Mode Rev. 1.00 92 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SLOW Mode to FAST Mode Switching In SLOW mode the system clock is derived from fSUB. When system clock is switched back to the FAST mode from fSUB, the CKS2~CKS0 bits should be set to "000" ~ "110" and then the system clock will respectively be switched to fH ~ fH/64. However, if fH is not used in SLOW mode and thus switched off, it will take some time to reoscillate and stabilise when switching to the FAST mode from the SLOW Mode. This is monitored using the HXTF bit in the HXTC register or the HIRCF bit in the HIRCC register. The time duration required for the high speed system oscillator stabilization is specified in the relevant characteristics. SLOW Mode CKS2~CKS0 = 000~110 FAST Mode FHIDEN=0, FSIDEN=0 HALT instruction is executed SLEEP Mode FHIDEN=0, FSIDEN=1 HALT instruction is executed IDLE0 Mode FHIDEN=1, FSIDEN=1 HALT instruction is executed IDLE1 Mode FHIDEN=1, FSIDEN=0 HALT instruction is executed IDLE2 Mode Entering the SLEEP Mode There is only one way for the device to enter the SLEEP Mode and that is to execute the "HALT" instruction in the application program with both the FHIDEN and FSIDEN bits in the SCC register equal to "0". In this mode all the clocks and functions will be switched off except the WDT function. When this instruction is executed under the conditions described above, the following will occur: • The system clock will be stopped and the application program will stop at the "HALT" instruction. • The Data Memory contents and registers will maintain their present condition. • The I/O ports will maintain their present conditions. • In the status register, the Power Down flag PDF will be set, and WDT timeout flag TO will be cleared. • The WDT will be cleared and resume counting if the WDT function is enabled by the WDTC register. Rev. 1.00 93 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Entering the IDLE0 Mode There is only one way for the device to enter the IDLE0 Mode and that is to execute the "HALT" instruction in the application program with the FHIDEN bit in the SCC register equal to "0" and the FSIDEN bit in the SCC register equal to "1". When this instruction is executed under the conditions described above, the following will occur: • The fH clock will be stopped and the application program will stop at the "HALT" instruction, but the fSUB clock will be on. • The Data Memory contents and registers will maintain their present condition. • The I/O ports will maintain their present conditions. • In the status register, the Power Down flag PDF will be set, and WDT timeout flag TO will be cleared. • The WDT will be cleared and resume counting if the WDT function is enabled by the WDTC register. Entering the IDLE1 Mode There is only one way for the device to enter the IDLE1 Mode and that is to execute the "HALT" instruction in the application program with both the FHIDEN and FSIDEN bits in the SCC register equal to "1". When this instruction is executed under the conditions described above, the following will occur: • The fH and fSUB clocks will be on but the application program will stop at the "HALT" instruction. • The Data Memory contents and registers will maintain their present condition. • The I/O ports will maintain their present conditions. • In the status register, the Power Down flag PDF will be set, and WDT timeout flag TO will be cleared. • The WDT will be cleared and resume counting if the WDT function is enabled by the WDTC register. Entering the IDLE2 Mode There is only one way for the device to enter the IDLE2 Mode and that is to execute the "HALT" instruction in the application program with the FHIDEN bit in the SCC register equal to "1" and the FSIDEN bit in the SCC register equal to "0". When this instruction is executed under the conditions described above, the following will occur: • The fH clock will be on but the fSUB clock will be off and the application program will stop at the "HALT" instruction. • The Data Memory contents and registers will maintain their present condition. • The I/O ports will maintain their present conditions. • In the status register, the Power Down flag PDF will be set, and WDT timeout flag TO will be cleared. • The WDT will be cleared and resume counting if the WDT function is enabled by the WDTC register. Rev. 1.00 94 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Standby Current Considerations As the main reason for entering the SLEEP or IDLE Mode is to keep the current consumption of the device to as low a value as possible, perhaps only in the order of several micro-amps except in the IDLE1 and IDLE2 Mode, there are other considerations which must also be taken into account by the circuit designer if the power consumption is to be minimised. Special attention must be made to the I/O pins on the device. All high-impedance input pins must be connected to either a fixed high or low level as any floating input pins could create internal oscillations and result in increased current consumption. This also applies to devices which have different package types, as there may be unbonded pins. These must either be setup as outputs or if setup as inputs must have pull-high resistors connected. Care must also be taken with the loads, which are connected to I/O pins, which are setup as outputs. These should be placed in a condition in which minimum current is drawn or connected only to external circuits that do not draw current, such as other CMOS inputs. Also note that additional standby current will also be required if the LIRC oscillator has enabled. In the IDLE1 and IDLE 2 Mode the high speed oscillator is on, if the peripheral function clock source is derived from the high speed oscillator, the additional standby current will also be perhaps in the order of several hundred micro-amps. Wake-up To minimise power consumption the device can enter the SLEEP or any IDLE Mode, where the CPU will be switched off. However, when the device is woken up again, it will take a considerable time for the original system oscillator to restart, stabilise and allow normal operation to resume. After the system enters the SLEEP or IDLE Mode, it can be woken up from one of various sources listed as follows: • An external falling edge on Port A • An external reset • A system interrupt • A WDT overflow When the device executes the "HALT" instruction, the PDF flag will be set to 1. The PDF flag will be cleared to 0 if the device experiences a system power-up or executes the clear Watchdog Timer instruction. If the system is woken up by a WDT overflow, a Watchdog Timer reset will be initiated and the TO flag will be set to 1. The TO flag is set if a WDT time-out occurs and causes a wake-up that only resets the Program Counter and Stack Pointer, other flags remain in their original status. Each pin on Port A can be setup using the PAWU register to permit a negative transition on the pin to wake up the system. When a Port A pin wake-up occurs, the program will resume execution at the instruction following the "HALT" instruction. If the system is woken up by an interrupt, then two possible situations may occur. The first is where the related interrupt is disabled or the interrupt is enabled but the stack is full, in which case the program will resume execution at the instruction following the "HALT" instruction. In this situation, the interrupt which woke up the device will not be immediately serviced, but will rather be serviced later when the related interrupt is finally enabled or when a stack level becomes free. The other situation is where the related interrupt is enabled and the stack is not full, in which case the regular interrupt response takes place. If an interrupt request flag is set high before entering the SLEEP or IDLE Mode, the wake-up function of the related interrupt will be disabled. Rev. 1.00 95 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Watchdog Timer The Watchdog Timer is provided to prevent program malfunctions or sequences from jumping to unknown locations, due to certain uncontrollable external events such as electrical noise. Watchdog Timer Clock Source The Watchdog Timer clock source is provided by the internal RC oscillator, fLIRC. The LIRC internal oscillator has an approximate frequency of 32 kHz and this specified internal clock period can vary with VDD, temperature and process variations. The Watchdog Timer source clock is then subdivided by a ratio of 28 to 218 to give longer timeouts, the actual value being chosen using the WS2~WS0 bits in the WDTC register. Watchdog Timer Control Register A single register, WDTC, controls the required timeout period as well as the enable/disable operation. This register controls the overall operation of the Watchdog Timer. WDTC Register Bit 7 6 5 4 3 2 1 0 Name WE4 WE3 WE2 WE1 WE0 WS2 WS1 WS0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 1 0 1 0 0 1 1 Bit 7~3 Bit 2~0 WE4~WE0: WDT function enable control 10101: Disabled 01010: Enabled Other values: Reset MCU If these bits are changed due to adverse environmental conditions, the microcontroller will be reset. The reset operation will be activated after a delay time, tSRESET, and the WRF bit in the RSTFC register will be set to 1. WS2~WS0: WDT time-out period selection 000: 28/fLIRC 001: 210/fLIRC 010: 212/fLIRC 011: 214/fLIRC 100: 215/fLIRC 101: 216/fLIRC 110: 217/fLIRC 111: 218/fLIRC These three bits determine the division ratio of the watchdog timer source clock, which in turn determines the time-out period. RSTFC Register Bit 7 6 5 4 3 2 1 0 Name — — — — RSTF LVRF LRF WRF R/W R/W — — — — R/W R/W R/W POR — — — — 0 x 0 Bit 7~4 Bit 3 Bit 2 Bit 1 Rev. 1.00 Unimplemented, read as "0" RSTF: Reset control register software reset flag Described elsewhere. LVRF: LVR function reset flag Described elsewhere. LRF: LVR control register software reset flag Described elsewhere. 96 0 "x": unknown December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 0 WRF: WDT control register software reset flag 0: Not occurred 1: Occurred This bit is set to 1 by the WDT control register software reset and cleared by the application program. Note that this bit can only be cleared to 0 by the application program. Watchdog Timer Operation The Watchdog Timer operates by providing a device reset when its timer overflows. This means that in the application program and during normal operation the user has to strategically clear the Watchdog Timer before it overflows to prevent the Watchdog Timer from executing a reset. This is done using the clear watchdog instruction. If the program malfunctions for whatever reason, jumps to an unknown location, or enters an endless loop, the clear instruction will not be executed in the correct manner, in which case the Watchdog Timer will overflow and reset the device. With regard to the Watchdog Timer enable/disable function, there are five bits, WE4~WE0, in the WDTC register to offer the enable/disable control and reset control of the Watchdog Timer. The WDT function will be enabled when the WE4~WE0 bits are set to a value of 01010B while the WDT function will be disabled if the WE4~WE0 bits are equal to 10101B. If the WE4~WE0 bits are set to any other values rather than 01010B and 10101B, it will reset the device after a delay time, tSRESET. After power on these bits will have a value of 01010B. WE4 ~ WE0 Bits WDT Function 10101B Disable 01010B Enable Any other value Reset MCU Watchdog Timer Enable/Disable Control Under normal program operation, a Watchdog Timer time-out will initialise a device reset and set the status bit TO. However, if the system is in the SLEEP or IDLE Mode, when a Watchdog Timer time-out occurs, the TO bit in the status register will be set and only the Program Counter and Stack Pointer will be reset. Four methods can be adopted to clear the contents of the Watchdog Timer. The first is a WDT reset, which means a certain value except 01010B and 10101B written into the WE4~WE0 field, the second is using the Watchdog Timer software clear instruction and the third is via a HALT instruction. The last is an external hardware reset, which means a low level on the external reset pin if the external reset pin exists by the RSTC register. There is only one method of using software instruction to clear the Watchdog Timer. That is to use the single "CLR WDT" instruction to clear the WDT contents. The maximum time out period is when the 218 division ratio is selected. As an example, with a 32 kHz LIRC oscillator as its source clock, this will give a maximum watchdog period of around 8 second for the 218 division ratio and a minimum timeout of 8ms for the 28 division ration. WDTC WE4~WE0 bits Register Reset MCU CLR “HALT”Instruction “CLR WDT”Instruction External reset pin reset LIRC fLIRC 8-stage Divider fLIRC/28 WS2~WS0 (fLIRC/28 ~ fLIRC/218) WDT Prescaler 8-to-1 MUX WDT Time-out (28/fLIRC ~ 218/fLIRC) Watchdog timer Rev. 1.00 97 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Reset and Initialisation A reset function is a fundamental part of any microcontroller ensuring that the device can be set to some predetermined condition irrespective of outside parameters. The most important reset condition is after power is first applied to the microcontroller. In this case, internal circuitry will ensure that the microcontroller, after a short delay, will be in a well defined state and ready to execute the first program instruction. After this power-on reset, certain important internal registers will be set to defined states before the program commences. One of these registers is the Program Counter, which will be reset to zero forcing the microcontroller to begin program execution from the lowest Program Memory address. In addition to the power-on reset, situations may arise where it is necessary to forcefully apply a reset condition when the microcontroller is already running, the RES line is forcefully pulled low. In such a case, known as a normal operation reset, some of the microcontroller registers remain unchanged allowing the microcontroller to preceed with normal operation after the reset line is allowed to return high. The Watchdog Timer overflow is one of many reset types and will reset the microcontroller. Another reset exists in the form of a Low Voltage Reset, LVR, where a full reset, similar to the RES reset is implemented in situations where the power supply voltage falls below a certain threshold. Another type of reset is when the Watchdog Timer overflows and resets the microcontroller. All types of reset operations result in different register conditions being setup. Reset Functions There are five ways in which a microcontroller reset can occur, through events occurring both internally and externally. Power-on Reset The most fundamental and unavoidable reset is the one that occurs after power is first applied to the microcontroller. As well as ensuring that the Program Memory begins execution from the first memory address, a power-on reset also ensures that certain other registers are preset to known conditions. All the I/O port and port control registers will power up in a high condition ensuring that all pins will be first set to inputs. VDD Powe�-on Reset tRSTD SST Ti�e-out Note: tRSTD is power-on delay with typical time=48 ms Power-On Reset Timing Chart Rev. 1.00 98 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM RES Pin Reset As the reset pin is shared with I/O pins, the reset function must be selected using a control register, RSTC. Although the microcontroller has an internal RC reset function, if the VDD power supply rise time is not fast enough or does not stabilise quickly at power-on, the internal reset function may be incapable of providing proper reset operation. For this reason it is recommended that an external RC network is connected to the RES pin, whose additional time delay will ensure that the RES pin remains low for an extended period to allow the power supply to stabilise. During this time delay, normal operation of the microcontroller will be inhibited. After the RES line reaches a certain voltage value, the reset delay time, tRSTD, is invoked to provide an extea delay time after which the microcontroller will begin normal operation. The abbreviation SST in the figures stands for System Start-up Time. For most applications a resistor connected between VDD and the RES line and a capacitor connected betweeb VSS and the RES pin will provide a suitable external reset circuit. Any wiring connected to the RES pin should be kept as short as possible to minimise any stray noise interference. For applications that operate within an environment where more noise is present the Enhanced Reset Circuit shown is recommended. VDD 0.01µF** 1N4148* VDD 10kΩ~ 100kΩ 300Ω* RES 0.1µF~1µF VSS Note: "*" It is recommended that this component is added for added ESD protection. "**" It is recommended that this component is added in environments where power line noise is significant. External RES Circuit Pulling the RES pin low using external hardware will also execute a device reset. In this case, as in the case of other resets, the Program Counter will reset to zero and program execution initiated from this point. RES 0.4VDD Internal Reset 0.9VDD tRSTD + tSST Note: tRSTD is power-on delay with typical time=16 ms RES Reset Timing Chart Rev. 1.00 99 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM There is an internal reset control register, RSTC, which is used to select the external RES pin function and provide a reset when the device operates abnormally due to the environmental noise interference. If the content of the RSTC register is set to any value other than 01010101B or 10101010B, it will reset the device after a delay time, tSRESET. After power on the register will have a value of 01010101B. RSTC7 ~ RSTC0 Bits Reset Function 01010101B I/O 10101010B RES Any other value Reset MCU Internal Reset Function Control • RSTC Register Bit 7 6 5 4 3 2 1 0 Name RSTC7 RSTC6 RSTC5 RSTC4 RSTC3 RSTC2 RSTC1 RSTC0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 1 0 1 0 1 0 1 Bit 7~0 RSTC7~RSTC0: Reset function control 01010101: I/O pin 10101010: RES pin Other values: Reset MCU If these bits are changed due to adverse environmental conditions, the microcontroller will be reset. The reset operation will be activated after a delay time, tSRESET, and the RSTF bit in the RSTFC register will be set to 1. All resets will reset this register to POR value except the WDT time out hardware warm reset. Note that if the register is set to 10101010 to select the RES pin, this configuration has higher priority than other related pin-shared controls. • RSTFC Register Bit 7 6 5 4 3 2 1 0 Name — — — — RSTF LVRF LRF WRF R/W — — — — R/W R/W R/W R/W POR — — — — 0 x 0 0 "x": unknown Rev. 1.00 Bit 7~4 Unimplemented, read as "0" Bit 3 RSTF: Reset control register software reset flag 0: Not occurred 1: Occurred This bit is set to 1 by the RSTC control register software reset and cleared by the application program. Note that this bit can only be cleared to 0 by the application program. Bit 2 LVRF: LVR function reset flag Described elsewhere. Bit 1 LRF: LVR control register software reset flag Described elsewhere. Bit 0 WRF: WDT control register software reset flag Described elsewhere. 100 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Low Voltage Reset – LVR The microcontroller contains a low voltage reset circuit in order to monitor the supply voltage of the device. The LVR function is always enabled with a specific LVR voltage, VLVR. If the supply voltage of the device drops to within a range of 0.9V~VLVR such as might occur when changing the battery, the LVR will automatically reset the device internally and the LVRF bit in the RSTFC register will also be set to 1. For a valid LVR signal, a low supply voltage, i.e., a voltage in the range between 0.9V~VLVR must exist for a time greater than that specified by tLVR in the LVD/LVR Electrical characteristics. If the low supply voltage state does not exceed this value, the LVR will ignore the low supply voltage and will not perform a reset function. The actual VLVR value can be selected by the LVS bits in the LVRC register. If the LVS7~LVS0 bits have any other value, which may perhaps occur due to adverse environmental conditions such as noise, the LVR will reset the device after a delay time, tSRESET. When this happens, the LRF bit in the RSTFC register will be set to 1. After power on the register will have the value of 01010101B. Note that the LVR function will be automatically disabled when the device enters the power down mode. LVR tRSTD + tSST Internal Reset Note: tRSTD is power-on delay with typical time=48 ms Low Voltage Reset Timing Chart • LVRC Register Bit 7 6 5 4 3 2 1 0 Name LVS7 LVS6 LVS5 LVS4 LVS3 LVS2 LVS1 LVS0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 1 0 1 0 1 0 1 Bit 7~0 LVS7~LVS0: LVR voltage select 01010101: 2.1V 00110011: 2.55V 10011001: 3.15V 10101010: 3.8V Other values: Generates a MCU reset – register is reset to POR value When an actual low voltage condition occurs, as specified by one of the four defined LVR voltage value above, an MCU reset will generated. The reset operation will be activated after the low voltage condition keeps more than a tLVR time. In this situation the register contents will remain the same after such a reset occurs. Any register value, other than the four defined register values above, will also result in the generation of an MCU reset. The reset operation will be activated after a delay time, tSRESET. However in this situation the register contents will be reset to the POR value. • RSTFC Register Bit 7 6 5 4 3 2 1 0 Name — — — — RSTF LVRF LRF WRF R/W — — — — R/W R/W R/W R/W POR — — — — 0 x 0 0 "x": unknown Rev. 1.00 Bit 7~4 Unimplemented, read as "0" Bit 3 RSTF: Reset control register software reset flag Described elsewhere. 101 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 2 LVRF: LVR function reset flag 0: Not occurred 1: Occurred This bit is set to 1 when a specific low voltage reset condition occurs. Note that this bit can only be cleared to 0 by the application program. Bit 1 LRF: LVR control register software reset flag 0: Not occurred 1: Occurred This bit is set to 1 by the LVRC control register contains any undefined LVR voltage register values. This in effect acts like a software-reset function. Note that this bit can only be cleared to 0 by the application program. Bit 0 WRF: WDT control register software reset flag Described elsewhere. Watchdog Time-out Reset during Normal Operation The Watchdog time-out Reset during normal operation is the same as the hardware Low Voltage Reset except that the Watchdog time-out flag TO will be set to "1". WDT Time-out tRSTD + tSST Internal Reset Note: tRSTD is power-on delay with typical time=16 ms WDT Time-out Reset during Normal Operation Timing Chart Watchdog Time-out Reset during SLEEP or IDLE Mode The Watchdog time-out Reset during SLEEP or IDLE Mode is a little different from other kinds of reset. Most of the conditions remain unchanged except that the Program Counter and the Stack Pointer will be cleared to "0" and the TO flag will be set to "1". Refer to the A.C. Characteristics for tSST details. WDT Time-out tSST Internal Reset WDT Time-out Reset during SLEEP or IDLE Mode Timing Chart Reset Initial Conditions The different types of reset described affect the reset flags in different ways. These flags, known as PDF and TO are located in the status register and are controlled by various microcontroller operations, such as the SLEEP or IDLE Mode function or Watchdog Timer. The reset flags are shown in the table: TO PDF Reset Function 0 0 Power-on reset u u RES or LVR reset during FAST or SLOW Mode operation 1 u WDT time-out reset during FAST or SLOW Mode operation 1 1 WDT time-out reset during IDLE or SLEEP Mode operation "u" stands for unchanged Rev. 1.00 102 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM The following table indicates the way in which the various components of the microcontroller are affected after a power-on reset occurs. Item Reset Function Program Counter Reset to zero Interrupts All interrupts will be disabled WDT, Time Base Clear after reset, WDT begins counting Timer Modules Timer Modules will be turned off Input/Output Ports I/O ports will be setup as inputs Stack pointer Stack pointer will point to the top of the stack The different kinds of resets all affect the internal registers of the microcontroller in different ways. To ensure reliable continuation of normal program execution after a reset occurs, it is important to know what condition the microcontroller is in after a particular reset occurs. The following table describes how each type of reset affects the microcontroller internal registers. HT67F2350 HT67F2360 HT67F2370 HT67F2390 Reset (Power On) IAR0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu MP0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu IAR1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu MP1L ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu MP1H ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu ACC ● ● ● ● xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu PCL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 0000 0000 TBLP ● ● ● ● xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu TBLH ● ● ● ● xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu TBHP ● ---x xxxx ---u uuuu ---u uuuu ---u uuuu ---u uuuu --xx xxxx --uu uuuu --uu uuuu --uu uuuu --uu uuuu -xxx xxxx -uuu uuuu -uuu uuuu -uuu uuuu -uuu uuuu ● xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ● xx00 xxxx uuuu uuuu uuuu uuuu xx1u uuuu u u 11 u u u u ---- ---0 ---- ---0 ---- ---0 ---- ---0 ---- ---u ---- --uu Register TBHP ● TBHP ● TBHP STATUS ● PBP ● ● ● PBP ● PBP RES Reset (Normal Operation) LVR Reset (Normal Operation) WDT Time-out WDT Time-out (Normal (IDLE/SLEEP) Operation) ---- --00 ---- --00 ---- --00 ---- --00 ● ---- -000 ---- -000 ---- -000 ---- -000 ---- -uuu IAR2 ● ● ● ● xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu MP2L ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu MP2H ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu RSTFC ● ● ● ● ---- 0x00 ---- uuuu ---- u1uu ---- uuuu ---- uuuu INTC0 ● ● ● ● -000 0000 -000 0000 -000 0000 -000 0000 -uuu uuuu INTC1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu INTC2 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu INTC3 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PA ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PAC ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PAPU ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PAWU ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PB ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PBC ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PBPU ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu Rev. 1.00 103 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM HT67F2350 HT67F2360 HT67F2370 HT67F2390 Reset (Power On) PC ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PCC ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PCPU ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PD ● ● ● ● - 111 1111 - 111 1111 - 111 1111 - 111 1111 -uuu uuuu PDC ● ● ● ● - 111 1111 - 111 1111 - 111 1111 - 111 1111 -uuu uuuu PDPU ● ● ● ● -000 0000 -000 0000 -000 0000 -000 0000 -uuu uuuu PE ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PEC ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PEPU ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PF ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PFC ● ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PFPU ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PG ● 1111 - - - - 1111 - - - - 1111 - - - - 1111 - - - - uuuu ---- 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu 1111 - - - - 1111 - - - - 1111 - - - - 1111 - - - - uuuu ---- 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu 0000 ---- 0000 ---- 0000 ---- 0000 ---- uuuu ---- Register PG PGC ● ● ● ● ● ● PGC PGPU ● ● RES Reset (Normal Operation) LVR Reset (Normal Operation) WDT Time-out WDT Time-out (Normal (IDLE/SLEEP) Operation) PGPU ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PH ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PHC ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PHPU ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu 11 - - 1111 11 - - 1111 11 - - 1111 11 - - 1111 uu-- uuuu ● ● ● 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu 11 - - 1111 11 - - 1111 11 - - 1111 11 - - 1111 uu-- uuuu 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu 00-- 0000 00-- 0000 00-- 0000 00-- 0000 uu-- uuuu uuuu uuuu PJ ● PJ PJC ● PJC PJPU ● ● ● ● PJPU ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 CRCCR ● ● ● ● ---- ---0 ---- ---0 ---- ---0 ---- ---0 ---- ---u CRCIN ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu CRCDL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu CRCDH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu IECC ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu RSTC ● ● ● ● 0101 0101 0101 0101 0101 0101 0101 0101 uuuu uuuu VBGRC ● ● ● ● ---- ---0 ---- ---0 ---- ---0 ---- ---0 ---- ---u INTEG ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu SCC ● ● ● ● 000- 0000 000- 0000 000- 0000 000- 0000 uuu- uuuu HIRCC ● ● ● ● ---- 0001 ---- 0001 ---- 0001 ---- 0001 ---- uuuu HXTC ● ● ● ● ---- -000 ---- -000 ---- -000 ---- -000 ---- -uuu LXTC ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu WDTC ● ● ● ● 0 1 0 1 0 0 11 0 1 0 1 0 0 11 0 1 0 1 0 0 11 0 1 0 1 0 0 11 uuuu uuuu LVRC ● ● ● ● 0101 0101 0101 0101 uuuu uuuu 0101 0101 uuuu uuuu LVDC ● ● ● ● --00 0000 --00 0000 --00 0000 --00 0000 --uu uuuu EEA ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu EEAL ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu EEAH ● ---- ---0 ---- ---0 ---- ---0 ---- ---0 ---- ---u Rev. 1.00 104 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM HT67F2350 HT67F2360 HT67F2370 HT67F2390 Reset (Power On) ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu EED ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu CP0C ● ● ● ● -000 00-- -000 00-- -000 00-- -000 00-- -uuu uu-- CP1C ● ● ● ● -000 00-- -000 00-- -000 00-- -000 00-- -uuu uu-- MFI0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu MFI1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu MFI2 ● ● ● ● --00 --00 --00 --00 --00 --00 --00 --00 --uu --uu MFI3 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu MFI4 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu MFI5 ● ● --00 --00 --00 --00 --00 --00 --00 --00 --uu --uu Register EEAH MFI5 RES Reset (Normal Operation) LVR Reset (Normal Operation) WDT Time-out WDT Time-out (Normal (IDLE/SLEEP) Operation) ● ● -000 -000 -000 -000 -000 -000 -000 -000 -uuu -uuu MFI6 ● ● ● -000 -000 -000 -000 -000 -000 -000 -000 -uuu -uuu MFI7 ● ● ● -000 -000 -000 -000 -000 -000 -000 -000 -uuu -uuu MFI8 ● ● ● -000 -000 -000 -000 -000 -000 -000 -000 -uuu -uuu MFI9 ● ● ● -000 -000 -000 -000 -000 -000 -000 -000 -uuu -uuu LCDC0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu LCDC1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu LCDC2 ● ● ● ● ---- -000 ---- -000 ---- -000 ---- -000 ---- -uuu SLEDC0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu SLEDC1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu SLEDC2 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu SLEDC3 ● ---- 00-- ---- 00-- ---- 00-- ---- 00-- ---- uu-- ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu SLEDC3 SLEDC4 ● ● ● ● ---- 0000 ---- 0000 ---- 0000 ---- 0000 ---- uuuu MDUWR0 ● ● ● ● xxxx xxxx 0000 0000 0000 0000 0000 0000 uuuu uuuu MDUWR1 ● ● ● ● xxxx xxxx 0000 0000 0000 0000 0000 0000 uuuu uuuu MDUWR2 ● ● ● ● xxxx xxxx 0000 0000 0000 0000 0000 0000 uuuu uuuu MDUWR3 ● ● ● ● xxxx xxxx 0000 0000 0000 0000 0000 0000 uuuu uuuu MDUWR4 ● ● ● ● xxxx xxxx 0000 0000 0000 0000 0000 0000 uuuu uuuu MDUWR5 ● ● ● ● xxxx xxxx 0000 0000 0000 0000 0000 0000 uuuu uuuu MDUWCTRL ● ● ● ● 00-- ---- 00-- ---- 00-- ---- 00-- ---- uu-- ---- CP0VOS ● ● ● ● -001 0000 -001 0000 -001 0000 -001 0000 -uuu uuuu CP1VOS ● ● ● ● -001 0000 -001 0000 -001 0000 -001 0000 -uuu uuuu PSC0R ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu TB0C ● ● ● ● 0--- -000 0--- -000 0--- -000 0--- -000 u--- -uuu TB1C ● ● ● ● 0--- -000 0--- -000 0--- -000 0--- -000 u--- -uuu PSC1R ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu SADOL ● ● ● ● xxxx ---- xxxx ---- xxxx ---- xxxx ---- SADOH ● ● ● ● xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu SADC0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 Rev. 1.00 105 uuuu ---(ADRFS=0) uuuu uuuu (ADRFS=0) uuuu uuuu (ADRFS=0) ---- uuuu (ADRFS=0) uuuu uuuu December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM HT67F2390 HT67F2370 HT67F2360 HT67F2350 Register Reset (Power On) RES Reset (Normal Operation) LVR Reset (Normal Operation) WDT Time-out WDT Time-out (Normal (IDLE/SLEEP) Operation) SADC1 ● ● ● ● 0000 -000 0000 -000 0000 -000 0000 -000 uuuu -uuu SADC2 ● ● ● ● 0-00 0000 0-00 0000 0-00 0000 0-00 0000 u-uu uuuu SIMC0 ● ● ● ● 111 - 0 0 0 0 111 - 0 0 0 0 111 - 0 0 0 0 111 - 0 0 0 0 uuu- uuuu SIMC1 ● ● ● ● 1000 0001 1000 0001 1000 0001 1000 0001 uuuu uuuu SIMD ● ● ● ● xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx uuuu uuuu SIMA/SIMC2 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu SIMTOC ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu SPIAC0 ● ● ● ● 111 - - - 0 0 111 - - - 0 0 111 - - - 0 0 111 - - - 0 0 uuu- --uu SPIAC1 ● ● ● ● --00 0000 --00 0000 --00 0000 --00 0000 --uu uuuu SPIAD ● ● ● ● xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx uuuu uuuu FARL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FARH ● ---0 0000 ---0 0000 ---0 0000 ---0 0000 ---u uuuu --00 0000 --00 0000 --00 0000 --00 0000 --uu uuuu -000 0000 -000 0000 -000 0000 -000 0000 -uuu uuuu FARH ● FARH ● FARH ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FD0L ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FD0H ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FD1L ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FD1H ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FD2L ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FD2H ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FD3L ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FD3H ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM0C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- PTM0C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM0DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM0DH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM0AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM0AH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM0RPL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM0RPH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu STM0C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- STM0C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM0DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM0DH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM0AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM0AH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM0RP ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu U0SR ● ● ● ● 0 0 0 0 1 0 11 0 0 0 0 1 0 11 0 0 0 0 1 0 11 0 0 0 0 1 0 11 uuuu uuuu U0CR1 ● ● ● ● 0000 00x0 0000 00x0 0000 00x0 0000 00x0 uuuu uuuu U0CR2 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu TXR_RXR0 ● ● ● ● xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx uuuu uuuu BRG0 ● ● ● ● xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx uuuu uuuu U1SR ● ● ● ● 0 0 0 0 1 0 11 0 0 0 0 1 0 11 0 0 0 0 1 0 11 0 0 0 0 1 0 11 uuuu uuuu U1CR1 ● ● ● ● 0000 00x0 0000 00x0 0000 00x0 0000 00x0 uuuu uuuu Rev. 1.00 106 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM HT67F2350 HT67F2360 HT67F2370 HT67F2390 Reset (Power On) U1CR2 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu TXR_RXR1 ● ● ● ● xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx uuuu uuuu BRG1 ● ● ● ● xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx uuuu uuuu U2SR ● ● 0 0 0 0 1 0 11 0 0 0 0 1 0 11 0 0 0 0 1 0 11 0 0 0 0 1 0 11 uuuu uuuu U2CR1 ● ● 0000 00x0 0000 00x0 0000 00x0 0000 00x0 uuuu uuuu U2CR2 ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu TXR_RXR2 ● ● xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx uuuu uuuu BRG2 ● ● xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx uuuu uuuu Register RES Reset (Normal Operation) LVR Reset (Normal Operation) WDT Time-out WDT Time-out (Normal (IDLE/SLEEP) Operation) PTM1C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- PTM1C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM1DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM1DH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM1AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM1AH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM1RPL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM1RPH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM2C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- PTM2C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM2DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM2DH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM2AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM2AH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM2RPL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM2RPH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM3C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- PTM3C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM3DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM3DH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM3AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM2AH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM3RPL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM3RPH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM1C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- STM1C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM1DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM1DH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM1AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM1AH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM1RP ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM2C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- STM2C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM2DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM2DH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM2AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu STM2AH ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu Rev. 1.00 107 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM HT67F2350 HT67F2360 HT67F2370 HT67F2390 Reset (Power On) STM2RP ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu EEC ● ● ● ● ---- 0000 ---- 0000 ---- 0000 ---- 0000 ---- uuuu FC0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FC1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu FC2 ● ● ● ● ---- ---0 ---- ---0 ---- ---0 ---- ---0 ---- ---u IFS0 ● ● ● ● -000 0000 -000 0000 -000 0000 -000 0000 -uuu uuuu Register RES Reset (Normal Operation) LVR Reset (Normal Operation) WDT Time-out WDT Time-out (Normal (IDLE/SLEEP) Operation) IFS1 ● ● ● ● -000 0000 -000 0000 -000 0000 -000 0000 -uuu uuuu IFS2 ● ● ● ● -000 0000 -000 0000 -000 0000 -000 0000 -uuu uuuu ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu IFS3 IFS4 ● ● IFS4 ● ● ---- -000 ---- -000 ---- -000 ---- -000 ---- -uuu PAS0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PAS1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PBS0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PBS1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PCS0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PCS1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PDS0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PDS1 ● ● ● ● --00 0000 --00 0000 --00 0000 --00 0000 --uu uuuu PES0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PES1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PFS0 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PFS1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PHS0 ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PHS1 ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu 0000 ---- 0000 ---- 0000 ---- 0000 ---- uuuu ---- PGS0 PGS1 ● PJS0 ● PJS1 ● PJS1 ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM4C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- PTM4C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM4DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM4DH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM4AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM4AH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM4RPL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM4RPH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM5C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- PTM5C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM5DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM5DH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM5AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM5AH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM5RPL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu Rev. 1.00 108 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM HT67F2390 HT67F2370 HT67F2360 HT67F2350 Register Reset (Power On) RES Reset (Normal Operation) LVR Reset (Normal Operation) WDT Time-out WDT Time-out (Normal (IDLE/SLEEP) Operation) PTM5RPH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM6C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- PTM6C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM6DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM6DH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM6AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM6AH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM6RPL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM6RPH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM7C0 ● ● ● ● 0000 0--- 0000 0--- 0000 0--- 0000 0--- uuuu u--- PTM7C1 ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM7DL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM7DH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM7AL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM7AH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu PTM7RPL ● ● ● ● 0000 0000 0000 0000 0000 0000 0000 0000 uuuu uuuu PTM7RPH ● ● ● ● ---- --00 ---- --00 ---- --00 ---- --00 ---- --uu Note: "u" stands for unchanged "x" stands for "unknown" "-" stands for unimplemented Rev. 1.00 109 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Input/Output Ports Holtek microcontrollers offer considerable flexibility on their I/O ports. With the input or output designation of every pin fully under user program control, pull-high selections for all ports and wake-up selections on certain pins, the user is provided with an I/O structure to meet the needs of a wide range of application possibilities. These devices provide bidirectional input/output lines. These I/O ports are mapped to the RAM Data Memory with specific addresses as shown in the Special Purpose Data Memory table. All of these I/O ports can be used for input and output operations. For input operation, these ports are non-latching, which means the inputs must be ready at the T2 rising edge of instruction "MOV A, [m]", where m denotes the port address. For output operation, all the data is latched and remains unchanged until the output latch is rewritten. Register Name Bit 7 6 5 4 3 2 1 0 PA PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PAC PAC7 PAC6 PAC5 PAC4 PAC3 PAC2 PAC1 PAC0 PAPU PAPU7 PAPU6 PAPU5 PAPU4 PAPU3 PAPU2 PAPU1 PAPU0 PAWU PAWU7 PAWU6 PAWU5 PAWU4 PAWU3 PAWU2 PAWU1 PAWU0 PB PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 PBC PBC7 PBC6 PBC5 PBC4 PBC3 PBC2 PBC1 PBC0 PBPU PBPU7 PBPU6 PBPU5 PBPU4 PBPU3 PBPU2 PBPU1 PBPU0 PC PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PCC PCC7 PCC6 PCC5 PCC4 PCC3 PCC2 PCC1 PCC0 PCPU PCPU7 PCPU6 PCPU5 PCPU4 PCPU3 PCPU2 PCPU1 PCPU0 PD — PD6 PD5 PD4 PD3 PD2 PD1 PD0 PDC — PDC6 PDC5 PDC4 PDC3 PDC2 PDC1 PDC0 PDPU — PDPU6 PDPU5 PDPU4 PDPU3 PDPU2 PDPU1 PDPU0 PE PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 PEC PEC7 PEC6 PEC5 PEC4 PEC3 PEC2 PEC1 PEC0 PEPU PEPU7 PEPU6 PEPU5 PEPU4 PEPU3 PEPU2 PEPU1 PEPU0 PF PF7 PF6 PF5 PF4 PF3 PF2 PF1 PF0 PFC PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 PFPU PFPU7 PFPU6 PFPU5 PFPU4 PFPU3 PFPU2 PFPU1 PFPU0 PG PG7 PG6 PG5 PG4 — — — — PGC PGC7 PGC6 PGC5 PGC4 — — — — PGPU PGPU7 PGPU6 PGPU5 PGPU4 — — — — PJ PJ7 PJ6 — — PJ3 PJ2 PJ1 PJ0 PJC PJC7 PJC6 — — PJC3 PJC2 PJC1 PJC0 PJPU PJPU7 PJPU6 — — PJPU3 PJPU2 PJPU1 PJPU0 "—": Unimplemented, read as "0" I/O Logic Function Registers List – HT67F2350 Rev. 1.00 110 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit Register Name 7 6 5 4 3 2 1 0 PA PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PAC PAC7 PAC6 PAC5 PAC4 PAC3 PAC2 PAC1 PAC0 PAPU PAPU7 PAPU6 PAPU5 PAPU4 PAPU3 PAPU2 PAPU1 PAPU0 PAWU PAWU7 PAWU6 PAWU5 PAWU4 PAWU3 PAWU2 PAWU1 PAWU0 PB PB7 PB6 PB5 PB4 PB3 PB2 PB1 PB0 PBC PBC7 PBC6 PBC5 PBC4 PBC3 PBC2 PBC1 PBC0 PBPU PBPU7 PBPU6 PBPU5 PBPU4 PBPU3 PBPU2 PBPU1 PBPU0 PC PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 PCC PCC7 PCC6 PCC5 PCC4 PCC3 PCC2 PCC1 PCC0 PCPU PCPU7 PCPU6 PCPU5 PCPU4 PCPU3 PCPU2 PCPU1 PCPU0 PD — PD6 PD5 PD4 PD3 PD2 PD1 PD0 PDC — PDC6 PDC5 PDC4 PDC3 PDC2 PDC1 PDC0 PDPU — PDPU6 PDPU5 PDPU4 PDPU3 PDPU2 PDPU1 PDPU0 PE PE7 PE6 PE5 PE4 PE3 PE2 PE1 PE0 PEC PEC7 PEC6 PEC5 PEC4 PEC3 PEC2 PEC1 PEC0 PEPU PEPU7 PEPU6 PEPU5 PEPU4 PEPU3 PEPU2 PEPU1 PEPU0 PF PF7 PF6 PF5 PF4 PF3 PF2 PF1 PF0 PFC PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 PFPU PFPU7 PFPU6 PFPU5 PFPU4 PFPU3 PFPU2 PFPU1 PFPU0 PG PG7 PG6 PG5 PG4 PG3 PG2 PG1 PG0 PGC PGC7 PGC6 PGC5 PGC4 PGC3 PGC2 PGC1 PGC0 PGPU PGPU7 PGPU6 PGPU5 PGPU4 PGPU3 PGPU2 PGPU1 PGPU0 PH PH7 PH6 PH5 PH4 PH3 PH2 PH1 PH0 PHC PHC7 PHC6 PHC5 PHC4 PHC3 PHC2 PHC1 PHC0 PHPU PHPU7 PHPU6 PHPU5 PHPU4 PHPU3 PHPU2 PHPU1 PHPU0 PJ PJ7 PJ6 PJ5 PJ4 PJ3 PJ2 PJ1 PJ0 PJC PJC7 PJC6 PJC5 PJC4 PJC3 PJC2 PJC1 PJC0 PJPU PJPU7 PJPU6 PJPU5 PJPU4 PJPU3 PJPU2 PJPU1 PJPU0 "—": Unimplemented, read as "0" I/O Logic Function Registers List – HT67F2360/HT67F2370/HT67F2390 Rev. 1.00 111 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pull-high Resistors Many product applications require pull-high resistors for their switch inputs usually requiring the use of an external resistor. To eliminate the need for these external resistors, all I/O pins, when configured as an input have the capability of being connected to an internal pull-high resistor. These pull-high resistors are selected using the relevant pull-high control registers and are implemented using weak PMOS transistors. Note that the pull-high resistor can be controlled by the relevant pull-high control register only when the pin-shared functional pin is selected as an input or NMOS output. Otherwise, the pull-high resistors can not be enabled. PxPU Register Bit 7 6 5 4 3 2 1 0 Name PxPU7 PxPU6 PxPU5 PxPU4 PxPU3 PxPU2 PxPU1 PxPU0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 PxPUn: I/O Port x Pin pull-high function control 0: Disable 1: Enable The PxPUn bit is used to control the pin pull-high function. Here the "x" is the Port name which can be A, B, C, D, E, F, G, H or J respectively depending upon the selected device. However, the actual available bits for each I/O Port may be different. Port A Wake-up The HALT instruction forces the microcontroller into the SLEEP or IDLE Mode which preserves power, a feature that is important for battery and other low-power applications. Various methods exist to wake-up the microcontroller, one of which is to change the logic condition on one of the Port A pins from high to low. This function is especially suitable for applications that can be woken up via external switches. Each pin on Port A can be selected individually to have this wake-up feature using the PAWU register. Note that the wake-up function can be controlled by the wake-up control registers only when the pin-shared functional pin is selected as general purpose input/output and the MCU enters the Power down mode. PAWU Register Bit 7 6 5 4 3 2 1 0 Name PAWU7 PAWU6 PAWU5 PAWU4 PAWU3 PAWU2 PAWU1 PAWU0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Rev. 1.00 PAWU7~PAWU0: Port A pin Wake-up function control 0: Disable 1: Enable 112 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM I/O Port Control Registers Each Port has its own control register which controls the input/output configuration. With this control register, each I/O pin with or without pull-high resistors can be reconfigured dynamically under software control. For the I/O pin to function as an input, the corresponding bit of the control register must be written as a "1". This will then allow the logic state of the input pin to be directly read by instructions. When the corresponding bit of the control register is written as a "0", the I/O pin will be setup as a CMOS output. If the pin is currently setup as an output, instructions can still be used to read the output register. However, it should be noted that the program will in fact only read the status of the output data latch and not the actual logic status of the output pin. PxC Register Bit 7 6 5 4 3 2 1 0 Name PxC7 PxC6 PxC5 PxC4 PxC3 PxC2 PxC1 PxC0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 1 1 1 1 1 1 1 1 PxCn: I/O Port x Pin type selection 0: Output 1: Input The PxCn bit is used to control the pin type selection. Here the "x" is the Port name which can be A, B, C, D, E, F, G, H or J respectively depending upon the selected device. However, the actual available bits for each I/O Port may be different. I/O Port Source Current Control These devices support different source current driving capability for each I/O port. With the selection register, SLEDCn, specific I/O port can support four levels of the source current driving capability. Users should refer to the I/O Port characteristics section to select the desired source current for different applications. Register Name Bit 7 6 5 4 3 2 1 0 SLEDC0 SLEDC07 SLEDC06 SLEDC05 SLEDC04 SLEDC03 SLEDC02 SLEDC01 SLEDC00 SLEDC1 SLEDC17 SLEDC16 SLEDC15 SLEDC14 SLEDC13 SLEDC12 SLEDC11 SLEDC10 SLEDC2 SLEDC27 SLEDC26 SLEDC25 SLEDC24 SLEDC23 SLEDC22 SLEDC21 SLEDC20 SLEDC3 (HT67F2350) SLEDC3 (HT67F2360/70/90) SLEDC4 — — — — SLEDC33 SLEDC32 — — SLEDC37 SLEDC36 SLEDC35 SLEDC34 SLEDC33 SLEDC32 SLEDC31 SLEDC30 — — — — SLEDC43 SLEDC42 SLEDC41 SLEDC40 I/O Port Source Current Control Registers List Rev. 1.00 113 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SLEDC0 Register Bit Name 7 6 5 4 3 2 1 0 SLEDC07 SLEDC06 SLEDC05 SLEDC04 SLEDC03 SLEDC02 SLEDC01 SLEDC00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 1 0 Bit 7~6 SLEDC07~SLEDC06: PB7~PB4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 5~4 SLEDC05~SLEDC04: PB3~PB0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 3~2 SLEDC03~SLEDC02: PA7~PA4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 1~0 SLEDC01~SLEDC00: PA3~PA0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) SLEDC1 Register Bit Name Rev. 1.00 7 6 5 4 3 2 SLEDC17 SLEDC16 SLEDC15 SLEDC14 SLEDC13 SLEDC12 SLEDC11 SLEDC10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 SLEDC17~SLEDC16: PD6~PD4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 5~4 SLEDC15~SLEDC14: PD3~PD0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 3~2 SLEDC13~SLEDC12: PC7~PC4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 1~0 SLEDC11~SLEDC10: PC3~PC0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) 114 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SLEDC2 Register Bit Name 7 6 5 4 3 2 1 0 SLEDC27 SLEDC26 SLEDC25 SLEDC24 SLEDC23 SLEDC22 SLEDC21 SLEDC20 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 SLEDC27~SLEDC26: PF7~PF4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 5~4 SLEDC25~SLEDC24: PF3~PF0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 3~2 SLEDC23~SLEDC22: PE4~PE7 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 1~0 SLEDC21~SLEDC20: PE3~PE0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) SLEDC3 Register – HT67F2350 Bit 7 6 5 4 Name — — — — 3 2 SLEDC33 SLEDC32 1 0 — — R/W — — — — R/W R/W — — POR — — — — 0 0 — — 1 0 Bit 7~4 Unimplemented, read as "0" Bit 3~2 SLEDC33~SLEDC32: PG7~PG4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 1~0 Unimplemented, read as "0" SLEDC3 Register – HT67F2360/HT67F2370/HT67F2390 Bit Name 6 5 4 3 2 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 Rev. 1.00 7 SLEDC37 SLEDC36 SLEDC35 SLEDC34 SLEDC33 SLEDC32 SLEDC31 SLEDC30 SLEDC37~SLEDC36: PH7~PH4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) 115 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 5~4 SLEDC35~SLEDC34: PH3~PH0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 3~2 SLEDC33~SLEDC32: PG7~PG4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 1~0 SLEDC31~SLEDC30: PG3~PG0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) SLEDC4 Register – HT67F2350 Bit 7 6 5 4 Name — — — — 3 2 1 0 SLEDC43 SLEDC42 SLEDC41 SLEDC40 R/W — — — — R/W R/W R/W R/W POR — — — — 0 0 0 0 2 1 0 Bit 7~4 Unimplemented, read as "0" Bit 3~2 SLEDC43~SLEDC42: PJ7~PJ6 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 1~0 SLEDC41~SLEDC40: PJ3~PJ0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) SLEDC4 Register – HT67F2360/HT67F2370/HT67F2390 Rev. 1.00 Bit 7 6 5 4 Name — — — — 3 SLEDC43 SLEDC42 SLEDC41 SLEDC40 R/W — — — — R/W R/W R/W R/W POR — — — — 0 0 0 0 Bit 7~4 Unimplemented, read as "0" Bit 3~2 SLEDC43~SLEDC42: PJ7~PJ4 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) Bit 1~0 SLEDC41~SLEDC40: PJ3~PJ0 source current selection 00: source current=Level 0 (min.) 01: source current=Level 1 10: source current=Level 2 11: source current=Level 3 (max.) 116 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Pin-shared Functions The flexibility of the microcontroller range is greatly enhanced by the use of pins that have more than one function. Limited numbers of pins can force serious design constraints on designers but by supplying pins with multi-functions, many of these difficulties can be overcome. For these pins, the desired function of the multi-function I/O pins is selected by a series of registers via the application program control. Pin-shared Function Selection Registers The limited number of supplied pins in a package can impose restrictions on the amount of functions a certain device can contain. However by allowing the same pins to share several different functions and providing a means of function selection, a wide range of different functions can be incorporated into even relatively small package sizes. Each device includes Port "x" output function Selection register "n", labeled as PxSn, and Input Function Selection register, labeled as IFSn, which can select the desired functions of the multi-function pin-shared pins. When the pin-shared input function is selected to be used, the corresponding input and output functions selection should be properly managed. For example, if the I2C SDA line is used, the corresponding output pin-shared function should be configured as the SDI/SDA function by configuring the PxSn register and the SDA signal input should be properly selected using the IFSn register. However, if the external interrupt function is selected to be used, the relevant output pinshared function should be selected as an I/O function and the interrupt input signal should be selected. The most important point to note is to make sure that the desired pin-shared function is properly selected and also deselected. For most pin-shared functions, to select the desired pin-shared function, the pin-shared function should first be correctly selected using the corresponding pin-shared control register. After that the corresponding peripheral functional setting should be configured and then the peripheral function can be enabled. However, a special point must be noted for some digital input pins, such as INTn, xTCKn, xTPnI, etc, which share the same pin-shared control configuration with their corresponding general purpose I/O functions when setting the relevant pin-shared control bit fields. To select these pin functions, in addition to the necessary pin-shared control and peripheral functional setup aforementioned, they must also be setup as an input by setting the corresponding bit in the I/O port control register. To correctly deselect the pin-shared function, the peripheral function should first be disabled and then the corresponding pin-shared function control register can be modified to select other pin-shared functions. Rev. 1.00 117 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Register Name PAS0 Bit 7 6 5 4 3 2 1 0 PAS07 PAS06 PAS05 PAS04 PAS03 PAS02 PAS01 PAS00 PAS1 PAS17 PAS16 PAS15 PAS14 PAS13 PAS12 PAS11 PAS10 PBS0 PBS07 PBS06 PBS05 PBS04 PBS03 PBS02 PBS01 PBS00 PBS1 PBS17 PBS16 PBS15 PBS14 PBS13 PBS12 PBS11 PBS10 PCS0 PCS07 PCS06 PCS05 PCS04 PCS03 PCS02 PCS01 PCS00 PCS1 PCS17 PCS16 PCS15 PCS14 PCS13 PCS12 PCS11 PCS10 PDS0 PDS07 PDS06 PDS05 PDS04 PDS03 PDS02 PDS01 PDS00 PDS1 — — PDS15 PDS14 PDS13 PDS12 PDS11 PDS10 PES0 PES07 PES06 PES05 PES04 PES03 PES02 PES01 PES00 PES1 PES17 PES16 PES15 PES14 PES13 PES12 PES11 PES10 PFS0 PFS07 PFS06 PFS05 PFS04 PFS03 PFS02 PFS01 PFS00 PFS1 PFS17 PFS16 PFS15 PFS14 PFS13 PFS12 PFS11 PFS10 PGS0 (HT67F2360/70/90) PGS07 PGS06 PGS05 PGS04 PGS03 PGS02 PGS01 PGS00 PGS1 PGS17 PGS16 PGS15 PGS14 PGS13 PGS12 PGS11 PGS10 PHS0 (HT67F2360/70/90) PHS07 PHS06 PHS05 PHS04 PHS03 PHS02 PHS01 PHS00 PHS1 (HT67F2360/70/90) PHS17 PHS16 PHS15 PHS14 PHS13 PHS12 PHS11 PHS10 PJS0 PJS07 PJS06 PJS05 PJS04 PJS03 PJS02 PJS01 PJS00 PJS1 (HT67F2350) PJS17 PJS16 PJS15 PJS14 — — — — PJS1 (HT67F2360/70/90) PJS17 PJS16 PJS15 PJS14 PJS13 PJS12 PJS11 PJS10 IFS0 — PTCK3PS PTCK2PS PTCK1PS PTCK0PS STCK2PS STCK1PS STCK0PS IFS1 — PTP3IPS IFS2 — SCSBPS SDISDAPS SCKSCLPS PTP2IPS PTP1IPS IFS3 PTCK7PS PTCK6PS PTCK5PS PTCK4PS (HT67F2360/70/90) PTP0IPS STP2IPS STP1IPS STP0IPS INT3PS INT2PS INT1PS INT0PS PTP7IPS PTP6IPS PTP5IPS PTP4IPS IFS4 (HT67F2350/60) — — — — — — RX1PS RX0PS IFS4 (HT67F2370/90) — — — — — RX2PS RX1PS RX0PS Pin-shared Function Selection Registers List Rev. 1.00 118 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • PAS0 Register Bit 7 6 5 4 3 2 1 0 Name PAS07 PAS06 PAS05 PAS04 PAS03 PAS02 PAS01 PAS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 Bit 5~4 Bit 3~2 Bit 1~0 PAS07~PAS06: PA3 pin function selection 00, 01: PA3/INT1 10: SDO 11: SEG25 PAS05~PAS04: PA2 pin function selection 00, 01, 10: PA2 11: SEG29 PAS03~PAS02: PA1 pin function selection 00, 01: PA1/INT0 10: SCS 11: SEG26 PAS01~PAS00: PA0 pin function selection 00, 01, 10: PA0 11: SEG30 • PAS1 Register Bit 7 6 5 4 3 2 1 0 Name PAS17 PAS16 PAS15 PAS14 PAS13 PAS12 PAS11 PAS10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 Bit 5~4 Bit 3~2 Bit 1~0 PAS17~PAS16: PA7 pin function selection 00, 01: PA7/INT1 10: TX0 11:SEG21 PAS15~PAS14: PA6 pin function selection 00, 01: PA6/INT0 10: RX0 11: SEG22 PAS13~PAS12: PA5 pin function selection 00, 01: PA5/INT3 10: SCK/SCL 11: SEG23 PAS11~PAS10: PA4 pin function selection 00, 01: PA4/INT2 10: SDI/SDA 11: SEG24 • PBS0 Register – HT67F2350/HT67F2360 Bit 7 6 5 4 3 2 1 0 Name PBS07 PBS06 PBS05 PBS04 PBS03 PBS02 PBS01 PBS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 Bit 5~4 Rev. 1.00 PBS07~PBS06: PB3 pin function selection 00, 01: PB3/PTP2I 10: PTP2 11: SEG27 PBS05~PBS04: PB2 pin function selection 00, 01: PB2/PTP3I/PTCK2 10: PTP3 11: SEG16 119 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 3~2 PBS03~PBS02: PB1 pin function selection 00, 01, 10: PB1/PTCK3 11: SEG31 Bit 1~0 PBS01~PBS00: PB0 pin function selection 00, 01: PB0/STCK2 10: C0X 11: SEG32 • PBS0 Register – HT67F2370 /HT67F2390 Bit 7 6 5 4 3 2 1 0 Name PBS07 PBS06 PBS05 PBS04 PBS03 PBS02 PBS01 PBS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PBS07~PBS06: PB3 pin function selection 00, 01: PB3/PTP2I 10: PTP2 11: SEG27 Bit 5~4 PBS05~PBS04: PB2 pin function selection 00, 01: PB2/PTP3I/PTCK2 10: PTP3 11: SEG16 Bit 3~2 PBS03~PBS02: PB1 pin function selection 00, 01: PB1/PTCK3 10: TX2 11: SEG31 Bit 1~0 PBS01~PBS00: PB0 pin function selection 00: PB0/STCK2 01: RX2 10: C0X 11: SEG32 • PBS1 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name PBS17 PBS16 PBS15 PBS14 PBS13 PBS12 PBS11 PBS10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PBS17~PBS16: PB7 pin function selection 00, 01: PB7/STCK1 10: OSC2 11: SEG34 Bit 5~4 PBS15~PBS14: PB6 pin function selection 00: PB6/STP1I 01: STP1 10: OSC1 11:SEG35 Bit 3~2 PBS13~PBS12: PB5 pin function selection 00, 01, 10: PB5/RES 11: SEG36 Bit 1~0 PBS11~PBS10: PB4 pin function selection 00, 01: PB4 10: C1X 11: SEG28 120 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • PCS0 Register Bit 7 6 5 4 3 2 1 0 Name PCS07 PCS06 PCS05 PCS04 PCS03 PCS02 PCS01 PCS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PCS07~PCS06: PC3 pin function selection 00: PC3/PTCK0/PTP4I 01: PTP4 10: AN3 11: SEG50 Bit 5~4 PCS05~PCS04: PC2 pin function selection 00: PC2/PTP0I 01: PTP0 10: AN2 11: SEG51 Bit 3~2 PCS03~PCS02: PC1 pin function selection 00: PC1 01: C0X 10: VREF 11: AN1 Bit 1~0 PCS01~PCS00: PC0 pin function selection 00: PC0 01: VREFI 10: AN0 11: SEG52 • PCS1 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name PCS17 PCS16 PCS15 PCS14 PCS13 PCS12 PCS11 PCS10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PCS17~PCS16: PC7 pin function selection 00: PC7/INT3/STCK0/PTP6I 01: PTP6 10: AN7 11: SEG46 Bit 5~4 PCS15~PCS14: PC6 pin function selection 00: PC6/STP0I 01: STP0 10: AN6 11: SEG47 Bit 3~2 PCS13~PCS12: PC5 pin function selection 00: PC5/PTCK1/PTP5I 01: PTP5 10: AN5 11: SEG48 Bit 1~0 PCS11~PCS10: PC4 pin function selection 00: PC4/PTP1I 01: PTP1 10: AN4 11: SEG49 121 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • PDS0 Register Bit 7 6 5 4 3 2 1 0 Name PDS07 PDS06 PDS05 PDS04 PDS03 PDS02 PDS01 PDS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PDS07~PDS06: PD3 pin function selection 00: PD3/PTCK2/PTP7I 01: PTP7 10: AN11 11: SEG43 Bit 5~4 PDS05~PDS04: PD2 pin function selection 00: PD2/PTP2I 01: PTP2 10: TX1 11: AN10 Bit 3~2 PDS03~PDS02: PD1 pin function selection 00: PD1/STCK1 01: RX1 10: AN9 11: SEG44 Bit 1~0 PDS01~PDS00: PD0 pin function selection 00: PD0/INT2/STP1I 01: STP1 10: AN8 11: SEG45 • PDS1 Register Bit Rev. 1.00 7 6 5 4 3 2 1 0 Name — — PDS15 PDS14 PDS13 PDS12 PDS11 PDS10 R/W — — R/W R/W R/W R/W R/W R/W POR — — 0 0 0 0 0 0 Bit 7~6 Unimplemented, read as "0" Bit 5~4 PDS15~PDS14: PD6 pin function selection 00: PD6/STP2I 01: STP2 10: C1X 11: SEG33 Bit 3~2 PDS13~PDS12: PD5 pin function selection 00: PD5/PTCK3 01: TX0 10: C1+ 11: SEG38 Bit 1~0 PDS11~PDS10: PD4 pin function selection 00: PD4/PTP3I 01: PTP3 10: RX0 11: C1− 122 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • PES0 Register Bit 7 6 5 4 3 2 1 0 Name PES07 PES06 PES05 PES04 PES03 PES02 PES01 PES00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PES07~PES06: PE3 pin function selection 00: PE3/PTP1I 01: PTP1 10: SCKA 11: SEG4 Bit 5~4 PES05~PES04: PE2 pin function selection 00, 01: PE2/PTCK1 10: SDIA 11: SEG5 Bit 3~2 PES03~PES02: PE1 pin function selection 00: PE1/STP0I 01: STP0 10: SDOA 11: SEG6 Bit 1~0 PES01~PES00: PE0 pin function selection 00, 01: PE0/STCK0 10: SCSA 11: SEG7 • PES1 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name PES17 PES16 PES15 PES14 PES13 PES12 PES11 PES10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PES17~PES16: PE7 pin function selection 00, 01: PE7 10: V2 11: SEG53 Bit 5~4 PES15~PES14: PE6 pin function selection 00, 01: PE6 10: C1 11: SEG54 Bit 3~2 PES13~PES12: PE5 pin function selection 00, 01: PE5 10: C2 11: SEG55 Bit 1~0 PES11~PES10: PE4 pin function selection 00, 01, 10: PE4 11: Unimplemented 123 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • PFS0 Register Bit 7 6 5 4 3 2 1 0 Name PFS07 PFS06 PFS05 PFS04 PFS03 PFS02 PFS01 PFS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PFS07~PFS06: PF3 pin function selection 00, 01: PF3 10: SCK/SCL 11: SEG12 Bit 5~4 PFS05~PFS04: PF2 pin function selection 00, 01: PF2 10: SDI/SDA 11: SEG13 Bit 3~2 PFS03~PFS02: PF1 pin function selection 00, 01: PF1 10: SDO 11: SEG14 Bit 1~0 PFS01~PFS00: PF0 pin function selection 00, 01: PF0 10: SCS 11: SEG15 • PFS1 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name PFS17 PFS16 PFS15 PFS14 PFS13 PFS12 PFS11 PFS10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PFS17~PFS16: PF7 pin function selection 00: PF7/STP2I 01: STP2 10: TX1 11: C0+ Bit 5~4 PFS15~PFS14: PF6 pin function selection 00: PF6/STCK2 01: RX1 10: C0− 11: SEG37 Bit 3~2 PFS13~PFS12: PF5 pin function selection 00, 01: PF5/PTP0I 10: PTP0 11: XT1 Bit 1~0 PFS11~PFS10: PF4 pin function selection 00, 01, 10: PF4/PTCK0 11: XT2 124 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • PGS0 Register – HT67F2360/HT67F2370/HT67F2390 Bit 7 6 5 4 3 2 1 0 Name PGS07 PGS06 PGS05 PGS04 PGS03 PGS02 PGS01 PGS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PGS07~PGS06: PG3 pin function selection 00, 01, 10: PG3 11: COM3 Bit 5~4 PGS05~PGS04: PG2 pin function selection 00, 01, 10: PG2 11: COM2 Bit 3~2 PGS03~PGS02: PG1 pin function selection 00, 01: PG1 10: TX2 11: COM1 Bit 1~0 PGS01~PGS00: PG0 pin function selection 00, 01: PG0 10: RX2 11: COM0 • PGS1 Register Bit 7 6 5 4 3 2 1 0 Name PGS17 PGS16 PGS15 PGS14 PGS13 PGS12 PGS11 PGS10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PGS17~PGS16: PG7 pin function selection 00, 01, 10: PG7 11: COM3 Bit 5~4 PGS15~PGS14: PG6 pin function selection 00, 01, 10: PG6 11: COM2 Bit 3~2 PGS13~PGS12: PG5 pin function selection 00, 01, 10: PG5 11: COM1 Bit 1~0 PGS11~PGS10: PG4 pin function selection 00, 01, 10: PG4 11: COM0 • PHS0 Register – HT67F2360/HT67F2370/HT67F2390 Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name PHS07 PHS06 PHS05 PHS04 PHS03 PHS02 PHS01 PHS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PHS07~PHS06: PH3 pin function selection 00, 01: PH3/PTCK5 10: AN13 11: SEG41 Bit 5~4 PHS05~PHS04: PH2 pin function selection 00, 01: PH2/PTCK4 10: AN12 11: SEG42 125 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 3~2 PHS03~PHS02: PH1 pin function selection 00, 01: PH1/PTP5I 10: PTP5 11: SEG19 Bit 1~0 PHS01~PHS00: PH0 pin function selection 00, 01: PH0/PTP4I 10: PTP4 11: SEG20 • PHS1 Register – HT67F2360/HT67F2370/HT67F2390 Bit 7 6 5 4 3 2 1 0 Name PHS17 PHS16 PHS15 PHS14 PHS13 PHS12 PHS11 PHS10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PHS17~PHS16: PH7 pin function selection 00, 01: PH7/PTP7I 10: PTP7 11: SEG17 Bit 5~4 PHS15~PHS14: PH6 pin function selection 00, 01: PH6/PTP6I 10: PTP6 11: SEG18 Bit 3~2 PHS13~PHS12: PH5 pin function selection 00, 01: PH5/PTCK7 10: AN15 11: SEG39 Bit 1~0 PHS11~PHS10: PH4 pin function selection 00, 01: PH4/PTCK6 10: AN14 11: SEG40 • PJS0 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name PJS07 PJS06 PJS05 PJS04 PJS03 PJS02 PJS01 PJS00 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PJS07~PHS06: PJ3 pin function selection 00, 01: PJ3 10: COM7 11: SEG3 Bit 5~4 PJS05~PJS04: PJ2 pin function selection 00, 01: PJ2 10: COM6 11: SEG2 Bit 3~2 PJS03~PJS02: PJ1 pin function selection 00, 01: PJ1 10: COM5 11: SEG1 Bit 1~0 PJS01~PJS00: PJ0 pin function selection 00, 01: PJ0 10: COM4 11: SEG0 126 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • PJS1 Register – HT67F2350 Bit 7 6 5 4 3 2 1 0 Name PJS17 PJS16 PJS15 PJS14 — — — — R/W R/W R/W R/W R/W — — — — POR 0 0 0 0 — — — — Bit 7~6 PJS17~PHS16: PJ7 pin function selection 00, 01, 10: PJ7/PTCK4 11: SEG11 Bit 5~4 PJS15~PJS14: PJ6 pin function selection 00, 01, 10: PJ6/PTCK5 11: SEG10 Bit 3~0 Unimplemented, read as "0" • PJS1 Register – HT67F2360/HT67F2370/HT67F2390 Bit 7 6 5 4 3 2 1 0 Name PJS17 PJS16 PJS15 PJS14 PJS13 PJS12 PJS11 PJS10 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 PJS17~PHS16: PJ7 pin function selection 00, 01, 10: PJ7/PTCK4 11: SEG11 Bit 5~4 PJS15~PJS14: PJ6 pin function selection 00, 01, 10: PJ6/PTCK5 11: SEG10 Bit 3~2 PJS13~PJS12: PJ5 pin function selection 00, 01, 10: PJ5/PTCK6 11: SEG9 Bit 1~0 PJS11~PJS10: PJ4 pin function selection 00, 01, 10: PJ4/PTCK7 11: SEG8 • IFS0 Register Bit 7 Name — 5 4 3 2 1 0 R/W — R/W R/W R/W R/W R/W R/W R/W POR — 0 0 0 0 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 PTCK3PS: PTCK3 input source pin selection 0: PD5 1: PB1 PTCK2PS: PTCK2 input source pin selection 0: PD3 1: PB2 PTCK1PS: PTCK1 input source pin selection 0: PC5 1: PE2 PTCK0PS: PTCK0 input source pin selection 0: PC3 1: PF4 STCK2PS: STCK2 input source pin selection 0: PF6 1: PB0 Bit 5 Bit 4 Bit 3 Bit 2 Rev. 1.00 6 PTCK3PS PTCK2PS PTCK1PS PTCK0PS STCK2PS STCK1PS STCK0PS 127 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 1 STCK1PS: STCK1 input source pin selection 0: PD1 1: PB7 Bit 0 STCK0PS: STCK0 input source pin selection 0: PC7 1: PE0 • IFS1 Register Bit 7 Name — 6 5 4 3 2 1 0 PTP3IPS PTP2IPS PTP1IPS PTP0IPS STP2IPS STP1IPS STP0IPS R/W — R/W R/W R/W R/W R/W R/W R/W POR — 0 0 0 0 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 PTP3IPS: PTP3I input source pin selection 0: PD4 1: PB2 Bit 5 PTP2IPS: PTP2I input source pin selection 0: PD2 1: PB3 Bit 4 PTP1IPS: PTP1I input source pin selection 0: PC4 1: PE3 Bit 3 PTP0IPS: PTP0I input source pin selection 0: PC2 1: PF5 Bit 2 STP2IPS: STP2I input source pin selection 0: PD6 1: PF7 Bit 1 STP1IPS: STP1I input source pin selection 0: PD0 1: PB6 Bit 0 STP0IPS: STP0I input source pin selection 0: PC6 1: PE1 • IFS2 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — SCSBPS SDISDAPS SCKSCLPS INT3PS INT2PS INT1PS INT0PS R/W — R/W R/W R/W R/W R/W R/W R/W POR — 0 0 0 0 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 SCSBPS: SCS input source pin selection 0: PA1 1: PF0 Bit 5 SDISDAPS: SDI/SDA input source pin selection 0: PA4 1: PF2 Bit 4 SCKSCLPS: SCK/SCL input source pin selection 0: PA5 1: PF3 128 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 3 Bit 2 Bit 1 Bit 0 INT3PS: INT3 input source pin selection 0: PA5 1: PC7 INT2PS: INT2 input source pin selection 0: PA4 1: PD0 INT1PS: INT1 input source pin selection 0: PA3 1: PA7 INT0PS: INT0 input source pin selection 0: PA1 1: PA6 • IFS3 Register – HT67F2360/HT67F2370/HT67F2390 Bit Name 7 6 5 4 3 2 1 0 PTCK7PS PTCK6PS PTCK5PS PTCK4PS PTP7IPS PTP6IPS PTP5IPS PTP4IPS R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 PTCK7PS: PTCK7 input source pin selection 0: PH5 1: PJ4 PTCK6PS: PTCK6 input source pin selection 0: PH4 1: PJ5 PTCK5PS: PTCK5 input source pin selection 0: PH3 1: PJ6 PTCK4PS: PTCK4 input source pin selection 0: PH2 1: PJ7 PTP7IPS: PTP7I input source pin selection 0: PD3 1: PH7 PTP6IPS: PTP6I input source pin selection 0: PC7 1: PH6 PTP5IPS: PTP5I input source pin selection 0: PC5 1: PH1 PTP4IPS: PTP4I input source pin selection 0: PC3 1: PH0 • IFS4 Register – HT67F2350/HT67F2360 Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — — — — — — RX1PS RX0PS R/W — — — — — — R/W R/W POR — — — — — — 0 0 Bit 7~2 Unimplemented, read as "0" Bit 1 RX1PS: RX1 input source pin selection 0: PD1 1: PF6 Bit 0 RX0PS: RX0 input source pin selection 0: PA6 1: PD4 129 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • IFS4 Register – HT67F2370/HT67F2390 Bit 7 6 5 4 3 2 1 0 Name — — — — — RX2PS RX1PS RX0PS R/W — — — — — R/W R/W R/W POR — — — — — 0 0 0 Bit 7~3 Unimplemented, read as "0" Bit 2 RX2PS: RX2 input source pin selection 0: PB2 1: PG0 Bit 1 RX1PS: RX1 input source pin selection 0: PD1 1: PF6 Bit 0 RX0PS: RX0 input source pin selection 0: PA6 1: PD4 I/O Pin Structures The accompanying diagram illustrates the internal structures of the I/O logic function. As the exact logical construction of the I/O pin will differ from this drawing, it is supplied as a guide only to assist with the functional understanding of the logic function I/O pins. The wide range of pin-shared structures does not permit all types to be shown. VDD Pull-high Register Select Control Bit Data Bus Write Control Register D CK Q S Weak Pull-up Q Chip RESET I/O pin Read Control Register Data Bit D Write Data Register CK Q S Q IECM M U X Read Data Register System Wake-up Wake-up Select PA only Logic Function Input/Output Structure Rev. 1.00 130 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM READ PORT Function The READ PORT function is used to manage the reading of the output data from the data latch or I/O pin, which is specially designed for the IEC60730 self-diagnostic test on the I/O function and A/D paths. There is a register, IECC, which is used to control the READ PORT function. If the READ PORT function is disabled, the pin function will operate as the selected pin-shared function. When a specific data pattern, "11001010", is written into the IECC register, the internal signal named IECM will be set high to enable the READ PORT function. If the READ PORT function is enabled, the value on the corresponding pins will be passed to the accumulator ACC when the read port instruction "mov acc, Px" is executed where the "x" stands for the corresponding I/O port name. IECC Register Bit 7 6 5 4 3 2 1 0 Name IECS7 IECS6 IECS5 IECS4 IECS3 IECS2 IECS1 IECS0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 IECS7~IECS0: READ PORT function enable control bit 7~ bit 0 11001010: IECM=1 – READ PORT function is enabled Others: IECM=0 – READ PORT function is disabled READ PORT Function Disabled Port Control Register Bit – PxC.n I/O Function Digital Input Function 1 I C SDA/SCL 1 0 Pin value Digital Output Function (except I2C SDA/SCL) 2 Enabled 0 0 Data latch value Pin value Pin value Analog Function 0 Note: The value on the above table is the content of the ACC register after "mov a, Px" instruction is executed where "x" means the relevant port name. The additional function of the READ PORT mode is to check the A/D path. When the READ PORT function is disabled, the A/D path from the external pin to the internal analog input will be switched off if the A/D input pin function is not selected by the corresponding selection bits. For the MCU with A/D converter channels, such as A/D AN15~AN0, the desired A/D channel can be switched on by properly configuring the external analog input channel selection bits in the A/D Control Register together with the corresponding analog input pin function is selected. However, the additional function of the READ PORT mode is to force the A/D path to be switched on. For example, when the AN0 is selected as the analog input channel as the READ PORT function is enabled, the AN0 analog input path will be switched on even if the AN0 analog input pin function is not selected. In this way, the AN0 analog input path can be examined by internally connecting the digital output on this shared pin with the AN0 analog input pin switch and then converting the corresponding digital data without any external analog input voltage connected. Rev. 1.00 131 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Digital Output Fun�tion AN0 READ PORT fun�tion ena�led� AN0 Pin-sha�ed path swit�hed on auto�ati�ally A/D Conve�te� AN15 Exte�nal analog input �hannel sele�tion A/D Channel Input Path Internally Connection Programming Considerations Within the user program, one of the things first to consider is port initialisation. After a reset, all of the I/O data and port control registers will be set to high. This means that all I/O pins will be defaulted to an input state, the level of which depends on the other connected circuitry and whether pull-high selections have been chosen. If the port control registers are then programmed to setup some pins as outputs, these output pins will have an initial high output value unless the associated port data registers are first programmed. Selecting which pins are inputs and which are outputs can be achieved byte-wide by loading the correct values into the appropriate port control register or by programming individual bits in the port control register using the "SET [m].i" and "CLR [m].i" instructions. Note that when using these bit control instructions, a read-modify-write operation takes place. The microcontroller must first read in the data on the entire port, modify it to the required new bit values and then rewrite this data back to the output ports. Port A has the additional capability of providing wake-up functions. When the device is in the SLEEP or IDLE Mode, various methods are available to wake the device up. One of these is a high to low transition of any of the Port A pins. Single or multiple pins on Port A can be setup to have this function. Rev. 1.00 132 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Timer Modules – TM One of the most fundamental functions in any microcontroller devices is the ability to control and measure time. To implement time related functions the device includes several Timer Modules, generally abbreviated to the name TM. The TMs are multi-purpose timing units and serve to provide operations such as Timer/Counter, Input Capture, Compare Match Output and Single Pulse Output as well as being the functional unit for the generation of PWM signals. Each of the TMs has two interrupts. The addition of input and output pins for each TM ensures that users are provided with timing units with a wide and flexible range of features. The common features of the different TM types are described here with more detailed information provided in the individual Standard and Periodic TM sections. Introduction These devices contain several TMs and each individual TM can be categorised as a certain type, namely Standard Type TM or Periodic Type TM. Although similar in nature, the different TM types vary in their feature complexity. The common features to all of the Standard and Periodic TMs will be described in this section and the detailed operation regarding each of the TM types will be described in separate sections. The main features and differences between the two types of TMs are summarised in the accompanying table. STM PTM Timer/Counter TM Function √ √ Input Capture √ √ Compare Match Output √ √ PWM Channels 1 1 Single Pulse Output PWM Alignment PWM Adjustment Period & Duty 1 1 Edge Edge Duty or Period Duty or Period TM Function Summary TM Operation The different types of TM offer a diverse range of functions, from simple timing operations to PWM signal generation. The key to understanding how the TM operates is to see it in terms of a free running count-up counter whose value is then compared with the value of pre-programmed internal comparators. When the free running count-up counter has the same value as the pre-programmed comparator, known as a compare match situation, a TM interrupt signal will be generated which can clear the counter and perhaps also change the condition of the TM output pin. The internal TM counter is driven by a user selectable clock source, which can be an internal clock or an external pin. TM Clock Source The clock source which drives the main counter in each TM can originate from various sources. The selection of the required clock source is implemented using the xTnCK2~xTnCK0 bits in the xTMn control registers, where "x" stands for S or P type TM and "n" stands for the specific TM serial number. The clock source can be a ratio of the system clock, fSYS, or the internal high clock, fH, the fSUB clock source or the external xTCKn pin. The xTCKn pin clock source is used to allow an external signal to drive the TM as an external clock source for event counting. Rev. 1.00 133 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM TM Interrupts The Standard or Periodic type TM has two internal interrupt, one for each of the internal comparator A or comparator P, which generate a TM interrupt when a compare match condition occurs. When a TM interrupt is generated, it can be used to clear the counter and also to change the state of the TM output pin. TM External Pins Each of the TMs, irrespective of what type, has two TM input pins, with the label xTCKn and xTPnI respectively. The xTMn input pin, xTCKn, is essentially a clock source for the xTMn and is selected using the xTnCK2~xTnCK0 bits in the xTMnC0 register. This external TM input pin allows an external clock source to drive the internal TM. The xTCKn input pin can be chosen to have either a rising or falling active edge. The STCKn and PTCKn pins are also used as the external trigger input pin in single pulse output mode for the STMn and PTMn respectively. The other xTM input pin, STPnI or PTPnI, is the capture input whose active edge can be a rising edge, a falling edge or both rising and falling edges and the active edge transition type is selected using the STnIO1~STnIO0 or PTnIO1~PTnIO0 bits in the STMnC1 or PTMnC1 register respectively. There is another capture input, PTCKn, for PTMn capture input mode, which can be used as the external trigger input source except the PTPnI pin. The TMs each have one output pin, xTPn. The TM output pin can be selected using the corresponding pin-shared function selection bits described in the Pin-shared Function section. When the TM is in the Compare Match Output Mode, these pins can be controlled by the TM to switch to a high or low level or to toggle when a compare match situation occurs. The external xTPn output pin is also the pin where the TM generates the PWM output waveform. As the TM output pins are pin-shared with other functions, the TM output function must first be setup using relevant pin-shared function selection register. Note that there is no relevant input function selection register, IFSn, to select the input signal source for the PTCK4~PTCK7 and PTP4I~PTP7I pins in the HT67F2350 device. Device HT67F2350 HT67F2360 HT67F2370 HT67F2390 STM Input STCK0, STP0I STCK1, STP1I STCK2, STP2I PTM Output Input Output STP0 STP1 STP2 PTCK0, PTP0I PTCK1, PTP1I PTCK2, PTP2I PTCK3, PTP3I PTCK4, PTP4I PTCK5, PTP5I PTCK6, PTP6I PTCK7, PTP7I PTP0 PTP1 PTP2 PTP3 PTP4 PTP5 PTP6 PTP7 TM External Pins Rev. 1.00 134 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM TM Input/Output Pin Selection Selecting to have a TM input/output or whether to retain its other shared function is implemented using the relevant pin-shared function selection registers, with the corresponding selection bits in each pin-shared function register corresponding to a TM input/output pin. Configuring the selection bits correctly will setup the corresponding pin as a TM input/output. The details of the pin-shared function selection are described in the pin-shared function section. Clo�k input CCR �aptu�e input STCKn STPnI STMn CCR output STPn STM Function Pin Control Block Diagram – n=0 ~ 2 Clo�k/�aptu�e input CCR �aptu�e input PTCKn PTPnI PTMn CCR output PTPn PTM Function Pin Control Block Diagram – n=0 ~ 7 Rev. 1.00 135 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Programming Considerations The TM Counter Registers and the Capture/Compare CCRA and CCRP registers, all have a low and high byte structure. The high bytes can be directly accessed, but as the low bytes can only be accessed via an internal 8-bit buffer, reading or writing to these register pairs must be carried out in a specific way. The important point to note is that data transfer to and from the 8-bit buffer and its related low byte only takes place when a write or read operation to its corresponding high byte is executed. As the CCRA and CCRP registers are implemented in the way shown in the following diagram and accessing these register pairs is carried out in a specific way as described above, it is recommended to use the "MOV" instruction to access the CCRA and CCRP low byte registers, named xTMnAL and PTMnRPL, using the following access procedures. Accessing the CCRA or CCRP low byte registers without following these access procedures will result in unpredictable values. xTMn Counte� Registe� (Read only) xTMnDL xTMnDH 8-�it Buffe� xTMnAL xTMnAH xTMn CCRA Registe� (Read/W�ite) PTMnRPL PTMnRPH PTMn CCRP Registe� (Read/W�ite) Data Bus The following steps show the read and write procedures: • Writing Data to CCRA or CCRP ♦♦ Step 1. Write data to Low Byte xTMnAL or PTMnRPL ––note that here data is only written to the 8-bit buffer. ♦♦ Step 2. Write data to High Byte xTMnAH or PTMnRPH ––here data is written directly to the high byte registers and simultaneously data is latched from the 8-bit buffer to the Low Byte registers. • Reading Data from the Counter Registers and CCRA or CCRP Rev. 1.00 ♦♦ Step 1. Read data from the High Byte xTMnDH, xTMnAH or PTMnRPH ––here data is read directly from the High Byte registers and simultaneously data is latched from the Low Byte register into the 8-bit buffer. ♦♦ Step 2. Read data from the Low Byte xTMnDL, xTMnAL or PTMnRPL ––this step reads data from the 8-bit buffer. 136 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Standard Type TM – STM The Standard Type TM contains five operating modes, which are Compare Match Output, Timer/ Event Counter, Capture Input, Single Pulse Output and PWM Output modes. The Standard TM can also be controlled with two external input pins and can drive one external output pin. Device STM Core STM Input Pin STM Output Pin HT67F2350 HT67F2360 HT67F2370 HT67F2390 16-bit STM (STM0, STM1, STM2) STCK0, STP0I STCK1, STP1I STCK2, STP2I STP0 STP1 STP2 CCRP fSYS/4 fSYS fH/16 fH/64 fSUB fSUB 8-bit Comparator P 001 011 16-bit Count-up Counter 100 101 STnON STnPAU Counter Clear 0 1 STnCCLR b0~b15 111 STnCK2~STnCK0 16-bit Comparator A STMnPF Interrupt STnOC b8~b15 010 110 STCKn Comparator P Match 000 Comparator A Match Output Control Polarity Control Pin Control STnM1, STnM0 STnIO1, STnIO0 STnPOL PxSn STPn STMnAF Interrupt STnIO1, STnIO0 Edge Detector CCRA STPnI Standard Type TM Block Diagram – n=0 ~ 2 Standard TM Operation The size of Standard TM is 16-bit wide and its core is a 16-bit count-up counter which is driven by a user selectable internal or external clock source. There are also two internal comparators with the names, Comparator A and Comparator P. These comparators will compare the value in the counter with CCRP and CCRA registers. The CCRP comparator is 8-bit wide whose value is compared the with highest 8 bits in the counter while the CCRA is the sixteen bits and therefore compares all counter bits. The only way of changing the value of the 16-bit counter using the application program, is to clear the counter by changing the STnON bit from low to high. The counter will also be cleared automatically by a counter overflow or a compare match with one of its associated comparators. When these conditions occur, a STM interrupt signal will also usually be generated. The Standard Type TM can operate in a number of different operational modes, can be driven by different clock sources including an input pin and can also control an output pin. All operating setup conditions are selected using relevant internal registers. Rev. 1.00 137 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Standard Type TM Register Description Overall operation of the Standard TM is controlled using a series of registers. A read only register pair exists to store the internal counter 16-bit value, while a read/write register pair exists to store the internal 16-bit CCRA value. The STMnRP register is used to store the 8-bit CCRP value. The remaining two registers are control registers which setup the different operating and control modes. Bit Register Name 7 6 5 4 3 2 1 0 STMnC0 STnPAU STnCK2 STnCK1 STnCK0 STnON — — — STMnC1 STnM1 STnM0 STnIO1 STnIO0 STnOC STMnDL D7 D6 D5 D4 D3 D2 STMnDH D15 D14 D13 D12 D11 D10 D9 D8 STMnAL D7 D6 D5 D4 D3 D2 D1 D0 STnPOL STnDPX D1 STnCCLR D0 STMnAH D15 D14 D13 D12 D11 D10 D9 D8 STMnRP STnRP7 STnRP6 STnRP5 STnRP4 STnRP3 STnRP2 STnRP1 STnRP0 16-bit Standard TM Registers List – n=0 ~ 2 STMnDL Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R R R R R R R R POR 0 0 0 0 0 0 0 0 Bit 7~0 STMn Counter Low Byte Register bit 7 ~ bit 0 STMn 16-bit Counter bit 7 ~ bit 0 STMnDH Register Bit 7 6 5 4 3 2 1 0 Name D15 D14 D13 D12 D11 D10 D9 D8 R/W R R R R R R R R POR 0 0 0 0 0 0 0 0 Bit 7~0 STMn Counter High Byte Register bit 7 ~ bit 0 STMn 16-bit Counter bit 15 ~ bit 8 STMnAL Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 STMn CCRA Low Byte Register bit 7 ~ bit 0 STMn 16-bit CCRA bit 7 ~ bit 0 STMnAH Register Bit 7 6 5 4 3 2 1 0 Name D15 D14 D13 D12 D11 D10 D9 D8 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Rev. 1.00 STMn CCRA High Byte Register bit 7 ~ bit 0 STMn 16-bit CCRA bit 15 ~ bit 8 138 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM STMnC0 Register Bit 7 6 5 4 3 2 1 0 Name STnPAU STnCK2 STnCK1 STnCK0 STnON — — — R/W R/W R/W R/W R/W R/W — — — POR 0 0 0 0 0 — — — Bit 7 STnPAU: STMn Counter Pause control 0: Run 1: Pause The counter can be paused by setting this bit high. Clearing the bit to zero restores normal counter operation. When in a Pause condition the STMn will remain powered up and continue to consume power. The counter will retain its residual value when this bit changes from low to high and resume counting from this value when the bit changes to a low value again. Bit 6~4 STnCK2~STnCK0: Select STMn Counter clock 000: fSYS/4 001: fSYS 010: fH/16 011: fH/64 100: fSUB 101: fSUB 110: STCKn rising edge clock 111: STCKn falling edge clock These three bits are used to select the clock source for the STMn. The external pin clock source can be chosen to be active on the rising or falling edge. The clock source fSYS is the system clock, while fH and fSUB are other internal clocks, the details of which can be found in the oscillator section. Bit 3 STnON: STMn Counter On/Off control 0: Off 1: On This bit controls the overall on/off function of the STMn. Setting the bit high enables the counter to run while clearing the bit disables the STMn. Clearing this bit to zero will stop the counter from counting and turn off the STMn which will reduce its power consumption. When the bit changes state from low to high the internal counter value will be reset to zero, however when the bit changes from high to low, the internal counter will retain its residual value until the bit returns high again. If the STMn is in the Compare Match Output Mode then the STMn output pin will be reset to its initial condition, as specified by the STnOC bit, when the STnON bit changes from low to high. Bit 2~0 Unimplemented, read as "0" STMnC1 Register Bit 7 6 5 4 3 Name STnM1 STnM0 STnIO1 STnIO0 STnOC R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 Rev. 1.00 2 1 STnPOL STnDPX 0 STnCCLR STnM1~STnM0: Select STMn Operating Mode 00: Compare Match Output Mode 01: Capture Input Mode 10: PWM Output Mode or Single Pulse Output Mode 11: Timer/Counter Mode These bits setup the required operating mode for the STMn. To ensure reliable operation the STMn should be switched off before any changes are made to the STnM1 and STnM0 bits. In the Timer/Counter Mode, the STMn output pin control will be disabled. 139 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Rev. 1.00 Bit 5~4 STnIO1~STnIO0: Select STMn external pin STPn function Compare Match Output Mode 00: No change 01: Output low 10: Output high 11: Toggle output PWM Output Mode/Single Pulse Output Mode 00: PWM output inactive state 01: PWM output active state 10: PWM output 11: Single Pulse Output Capture Input Mode 00: Input capture at rising edge of STPnI 01: Input capture at falling edge of STPnI 10: Input capture at rising/falling edge of STPnI 11: Input capture disabled Timer/Counter Mode Unused These two bits are used to determine how the STMn output pin changes state when a certain condition is reached. The function that these bits select depends upon in which mode the STMn is running. In the Compare Match Output Mode, the STnIO1 and STnIO0 bits determine how the STMn output pin changes state when a compare match occurs from the Comparator A. The TM output pin can be setup to switch high, switch low or to toggle its present state when a compare match occurs from the Comparator A. When the bits are both zero, then no change will take place on the output. The initial value of the STMn output pin should be setup using the STnOC bit in the STMnC1 register. Note that the output level requested by the STnIO1 and STnIO0 bits must be different from the initial value setup using the STnOC bit otherwise no change will occur on the STMn output pin when a compare match occurs. After the STMn output pin changes state, it can be reset to its initial level by changing the level of the STnON bit from low to high. In the PWM Output Mode, the STnIO1 and STnIO0 bits determine how the STMn output pin changes state when a certain compare match condition occurs. The PWM output function is modified by changing these two bits. It is necessary to only change the values of the STnIO1 and STnIO0 bits only after the STMn has been switched off. Unpredictable PWM outputs will occur if the STnIO1 and STnIO0 bits are changed when the STMn is running. Bit 3 STnOC: STMn STPn Output control Compare Match Output Mode 0: Initial low 1: Initial high PWM Output Mode/Single Pulse Output Mode 0: Active low 1: Active high This is the output control bit for the STMn output pin. Its operation depends upon whether STMn is being used in the Compare Match Output Mode or in the PWM Output Mode/Single Pulse Output Mode. It has no effect if the STMn is in the Timer/ Counter Mode. In the Compare Match Output Mode it determines the logic level of the STMn output pin before a compare match occurs. In the Output PWM Mode/Single Pulse Output Mode it determines if the PWM signal is active high or active low. 140 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 2 STnPOL: STMn STPn Output polarity control 0: Non-inverted 1: Inverted This bit controls the polarity of the STPn output pin. When the bit is set high the STMn output pin will be inverted and not inverted when the bit is zero. It has no effect if the STMn is in the Timer/Counter Mode. Bit 1 STnDPX: STMn PWM duty/period control 0: CCRP – period; CCRA – duty 1: CCRP – duty; CCRA – period This bit determines which of the CCRA and CCRP registers are used for period and duty control of the PWM waveform. Bit 0 STnCCLR: STMn Counter Clear condition selection 0: Comparator P match 1: Comparator A match This bit is used to select the method which clears the counter. Remember that the Standard TM contains two comparators, Comparator A and Comparator P, either of which can be selected to clear the internal counter. With the STnCCLR bit set high, the counter will be cleared when a compare match occurs from the Comparator A. When the bit is low, the counter will be cleared when a compare match occurs from the Comparator P or with a counter overflow. A counter overflow clearing method can only be implemented if the CCRP bits are all cleared to zero. The STnCCLR bit is not used in the PWM Output, Single Pulse Output or Capture Input Mode. STMnRP Register Bit 7 6 5 4 3 2 1 0 Name STnRP7 STnRP6 STnRP5 STnRP4 STnRP3 STnRP2 STnRP1 STnRP0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Rev. 1.00 STnRP7~STnRP0: STMn CCRP 8-bit register, compared with the STMn counter bit 15~bit 8 Comparator P match period = 0: 65536 STMn clocks 1~255: (1~255) × 256 STMn clocks These eight bits are used to setup the value on the internal CCRP 8-bit register, which are then compared with the internal counter’s highest eight bits. The result of this comparison can be selected to clear the internal counter if the STnCCLR bit is set to zero. Setting the STnCCLR bit to zero ensures that a compare match with the CCRP values will reset the internal counter. As the CCRP bits are only compared with the highest eight counter bits, the compare values exist in 256 clock cycle multiples. Clearing all eight bits to zero is in effect allowing the counter to overflow at its maximum value. 141 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Standard Type TM Operation Modes The Standard Type TM can operate in one of five operating modes, Compare Match Output Mode, PWM Output Mode, Single Pulse Output Mode, Capture Input Mode or Timer/Counter Mode. The operating mode is selected using the STnM1 and STnM0 bits in the STMnC1 register. Compare Match Output Mode To select this mode, bits STnM1 and STnM0 in the STMnC1 register, should be set to 00 respectively. In this mode once the counter is enabled and running it can be cleared by three methods. These are a counter overflow, a compare match from Comparator A and a compare match from Comparator P. When the STnCCLR bit is low, there are two ways in which the counter can be cleared. One is when a compare match from Comparator P, the other is when the CCRP bits are all zero which allows the counter to overflow. Here both STMnAF and STMnPF interrupt request flags for Comparator A and Comparator P respectively, will both be generated. If the STnCCLR bit in the STMnC1 register is high then the counter will be cleared when a compare match occurs from Comparator A. However, here only the STMnAF interrupt request flag will be generated even if the value of the CCRP bits is less than that of the CCRA registers. Therefore when STnCCLR is high no STMnPF interrupt request flag will be generated. In the Compare Match Output Mode, the CCRA can not be set to "0". As the name of the mode suggests, after a comparison is made, the STMn output pin, will change state. The STMn output pin condition however only changes state when a STMnAF interrupt request flag is generated after a compare match occurs from Comparator A. The STMnPF interrupt request flag, generated from a compare match occurs from Comparator P, will have no effect on the STMn output pin. The way in which the STMn output pin changes state are determined by the condition of the STnIO1 and STnIO0 bits in the STMnC1 register. The STMn output pin can be selected using the STnIO1 and STnIO0 bits to go high, to go low or to toggle from its present condition when a compare match occurs from Comparator A. The initial condition of the STMn output pin, which is setup after the STnON bit changes from low to high, is setup using the STnOC bit. Note that if the STnIO1 and STnIO0 bits are zero then no pin change will take place. Rev. 1.00 142 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� ove�flow Counte� Value CCRP=0 0xFFFF STnCCLR = 0; STnM [1:0] = 00 CCRP > 0 Counte� �lea�ed �y CCRP value CCRP > 0 Counte� Resta�t Resu�e CCRP Pause CCRA Stop Ti�e STnON STnPAU STnPOL CCRP Int. flag STMnPF CCRA Int. flag STMnAF STMn O/P Pin Output pin set to initial Level Low if STnOC=0 Output not affe�ted �y STMnAF flag. Re�ains High until �eset �y STnON �it Output Toggle with STMnAF flag He�e STnIO [1:0] = 11 Toggle Output sele�t Note STnIO [1:0] = 10 A�tive High Output sele�t Output Inve�ts Output Pin when STnPOL is high Reset to Initial value Output �ont�olled �y othe� pin-sha�ed fun�tion Compare Match Output Mode – STnCCLR=0 Note: 1. With STnCCLR=0 a Comparator P match will clear the counter 2. The STMn output pin is controlled only by the STMnAF flag 3. The output pin is reset to its initial state by a STnON bit rising edge 4. n=0 ~ 2 Rev. 1.00 143 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value STnCCLR = 1; STnM [1:0] = 00 CCRA = 0 Counte� ove�flow CCRA > 0 Counte� �lea�ed �y CCRA value 0xFFFF CCRA=0 Resu�e CCRA Pause Stop Counte� Resta�t CCRP Ti�e STnON STnPAU STnPOL No STMnAF flag gene�ated on CCRA ove�flow CCRA Int. flag STMnAF CCRP Int. flag STMnPF STMn O/P Pin STMnPF not gene�ated Output pin set to initial Level Low if STnOC=0 Output does not �hange Output not affe�ted �y STMnAF flag. Re�ains High until �eset �y STnON �it Output Toggle with STMnAF flag He�e STnIO [1:0] = 11 Toggle Output sele�t Note STnIO [1:0] = 10 A�tive High Output sele�t Output Inve�ts when STnPOL is high Output Pin Reset to Initial value Output �ont�olled �y othe� pin-sha�ed fun�tion Compare Match Output Mode –STnCCLR=1 Note: 1. With STnCCLR=1 a Comparator A match will clear the counter 2. The STMn output pin is controlled only by the STMnAF flag 3. The output pin is reset to its initial state by a STnON bit rising edge 4. A STMnPF flag is not generated when STnCCLR=1 5. n=0 ~ 2 Rev. 1.00 144 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Timer/Counter Mode To select this mode, bits STnM1 and STnM0 in the STMnC1 register should be set to 11 respectively. The Timer/Counter Mode operates in an identical way to the Compare Match Output Mode generating the same interrupt flags. The exception is that in the Timer/Counter Mode the STMn output pin is not used. Therefore the above description and Timing Diagrams for the Compare Match Output Mode can be used to understand its function. As the STMn output pin is not used in this mode, the pin can be used as a normal I/O pin or other pin-shared function. PWM Output Mode To select this mode, bits STnM1 and STnM0 in the STMnC1 register should be set to 10 respectively and also the STnIO1 and STnIO0 bits should be set to 10 respectively. The PWM function within the STMn is useful for applications which require functions such as motor control, heating control, illumination control etc. By providing a signal of fixed frequency but of varying duty cycle on the STMn output pin, a square wave AC waveform can be generated with varying equivalent DC RMS values. As both the period and duty cycle of the PWM waveform can be controlled, the choice of generated waveform is extremely flexible. In the PWM mode, the STnCCLR bit has no effect as the PWM period. Both of the CCRA and CCRP registers are used to generate the PWM waveform, one register is used to clear the internal counter and thus control the PWM waveform frequency, while the other one is used to control the duty cycle. Which register is used to control either frequency or duty cycle is determined using the STnDPX bit in the STMnC1 register. The PWM waveform frequency and duty cycle can therefore be controlled by the values in the CCRA and CCRP registers. As both the period and duty cycle of the PWM waveform can be controlled, the choice of generated waveform is extremely flexible. In the PWM Output mode, the STnCCLR bit has no effect as the PWM period. Both of the CCRA and CCRP registers are used to generate the PWM waveform, one register is used to clear the internal counter and thus control the PWM waveform frequency, while the other one is used to control the duty cycle. Which register is used to control either frequency or duty cycle is determined using the STnDPX bit in the STMnC1 register. The PWM waveform frequency and duty cycle can therefore be controlled by the values in the CCRA and CCRP registers. • 16-bit STMn, PWM Output Mode, Edge-aligned Mode, STnDPX=0 CCRP 1~255 0 Period CCRP × 256 65536 Duty CCRA If fSYS=16MHz, STMn clock source is fSYS/4, CCRP=2 and CCRA=128, The STMn PWM output frequency=(fSYS/4) / (2×256)=fSYS/2048=8 kHz, duty=128/(2×256)= 25%. If the Duty value defined by the CCRA register is equal to or greater than the Period value, then the PWM output duty is 100%. • 16-bit STMn, PWM Output Mode, Edge-aligned Mode, STnDPX=1 CCRP 1~255 Period Duty 0 CCRA CCRP × 256 65536 The PWM output period is determined by the CCRA register value together with the TM clock while the PWM duty cycle is defined by the CCRP register value except when the CCRP value is equal to 0. Rev. 1.00 145 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value STnDPX = 0; STnM [1:0] = 10 Counte� �lea�ed �y CCRP Counte� Reset when STnON �etu�ns high CCRP Pause Resu�e Counte� Stop if STnON �it low CCRA Ti�e STnON STnPAU STnPOL CCRA Int. flag STMnAF CCRP Int. flag STMnPF STMn O/P Pin (STnOC=1) STMn O/P Pin (STnOC=0) PWM Duty Cy�le set �y CCRA PWM Pe�iod set �y CCRP PWM �esu�es ope�ation Output �ont�olled �y othe� pin-sha�ed fun�tion Output Inve�ts when STnPOL = 1 PWM Output Mode – STnDPX=0 Note: 1. Here STnDPX=0 – Counter cleared by CCRP 2. A counter clear sets the PWM Period 3. The internal PWM function continues running even when STnIO [1:0]=00 or 01 4. The STnCCLR bit has no influence on PWM operation 5. n=0 ~ 2 Rev. 1.00 146 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value STnDPX = 1; STnM [1:0] = 10 Counte� �lea�ed �y CCRA Counte� Reset when STnON �etu�ns high CCRA Pause Resu�e Counte� Stop if STnON �it low CCRP Ti�e STnON STnPAU STnPOL CCRP Int. flag STMnPF CCRA Int. flag STMnAF STMn O/P Pin (STnOC=1) STMn O/P Pin (STnOC=0) PWM Duty Cy�le set �y CCRP PWM Pe�iod set �y CCRA Output �ont�olled �y othe� pin-sha�ed fun�tion PWM �esu�es ope�ation Output Inve�ts when STnPOL = 1 PWM Output Mode – STnDPX=1 Note: 1. Here STnDPX=1 – Counter cleared by CCRA 2. A counter clear sets the PWM Period 3. The internal PWM function continues even when STnIO [1:0]=00 or 01 4. The STnCCLR bit has no influence on PWM operation 5. n=0 ~ 2 Rev. 1.00 147 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Single Pulse Output Mode To select this mode, bits STnM1 and STnM0 in the STMnC1 register should be set to 10 respectively and also the STnIO1 and STnIO0 bits should be set to 11 respectively. The Single Pulse Output Mode, as the name suggests, will generate a single shot pulse on the STMn output pin. The trigger for the pulse output leading edge is a low to high transition of the STnON bit, which can be implemented using the application program. However in the Single Pulse Output Mode, the STnON bit can also be made to automatically change from low to high using the external STCKn pin, which will in turn initiate the Single Pulse output. When the STnON bit transitions to a high level, the counter will start running and the pulse leading edge will be generated. The STnON bit should remain high when the pulse is in its active state. The generated pulse trailing edge will be generated when the STnON bit is cleared to zero, which can be implemented using the application program or when a compare match occurs from Comparator A. However a compare match from Comparator A will also automatically clear the STnON bit and thus generate the Single Pulse output trailing edge. In this way the CCRA value can be used to control the pulse width. A compare match from Comparator A will also generate a STMn interrupt. The counter can only be reset back to zero when the STnON bit changes from low to high when the counter restarts. In the Single Pulse Output Mode CCRP is not used. The STnCCLR and STnDPX bits are not used in this Mode. S/W Command SET ˝STnON˝ or STCKn Pin Transition CCRA Leading Edge CCRA Trailing Edge STnON bit 0à1 STnON bit 1à0 S/W Command CLR ˝STnON˝ or CCRA Compare Match STPn Output Pin Pulse Width = CCRA Value Single Pulse Generation Rev. 1.00 148 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value STnM [1:0] = 10 ; STnIO [1:0] = 11 Counte� stopped �y CCRA Counte� Reset when STnON �etu�ns high CCRA Pause Counte� Stops �y softwa�e Resu�e CCRP Ti�e STnON Softwa�e T�igge� Clea�ed �y CCRA �at�h Auto. set �y STCKn pin STCKn pin Softwa�e T�igge� Softwa�e T�igge� Softwa�e Softwa�e T�igge� Clea� STCKn pin T�igge� STnPAU STnPOL CCRP Int. Flag STMnPF No CCRP Inte��upts gene�ated CCRA Int. Flag STMnAF STMn O/P Pin (STnOC=1) STMn O/P Pin (STnOC=0) Output Inve�ts when STnPOL = 1 Pulse Width set �y CCRA Single Pulse Output Mode Note: 1. Counter stopped by CCRA 2. CCRP is not used 3. The pulse triggered by the STCKn pin or by setting the STnON bit high 4. A STCKn pin active edge will automatically set the STnON bit high. 5. In the Single Pulse Output Mode, STnIO [1:0] must be set to "11" and can not be changed. 6. n=0 ~ 2 Rev. 1.00 149 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Capture Input Mode To select this mode bits STnM1 and STnM0 in the STMnC1 register should be set to 01 respectively. This mode enables external signals to capture and store the present value of the internal counter and can therefore be used for applications such as pulse width measurements. The external signal is supplied on the STPnI pin, whose active edge can be a rising edge, a falling edge or both rising and falling edges; the active edge transition type is selected using the STnIO1 and STnIO0 bits in the STMnC1 register. The counter is started when the STnON bit changes from low to high which is initiated using the application program. When the required edge transition appears on the STPnI pin the present value in the counter will be latched into the CCRA registers and a STMn interrupt generated. Irrespective of what events occur on the STPnI pin the counter will continue to free run until the STnON bit changes from high to low. When a CCRP compare match occurs the counter will reset back to zero; in this way the CCRP value can be used to control the maximum counter value. When a CCRP compare match occurs from Comparator P, a STMn interrupt will also be generated. Counting the number of overflow interrupt signals from the CCRP can be a useful method in measuring long pulse widths. The STnIO1 and STnIO0 bits can select the active trigger edge on the STPnI pin to be a rising edge, falling edge or both edge types. If the STnIO1 and STnIO0 bits are both set high, then no capture operation will take place irrespective of what happens on the STPnI pin, however it must be noted that the counter will continue to run. The STnCCLR and STnDPX bits are not used in this Mode. Rev. 1.00 150 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value STnM [1:0] = 01 Counte� �lea�ed �y CCRP Counte� Stop Counte� Reset CCRP Resu�e YY Pause XX Ti�e STnON STnPAU A�tive edge A�tive edge A�tive edge STMn �aptu�e pin STPnI CCRA Int. Flag STMnAF CCRP Int. Flag STMnPF CCRA Value STnIO [1:0] Value XX 00 – Rising edge YY 01 – Falling edge XX 10 – Both edges YY 11 – Disa�le Captu�e Capture Input Mode Note: 1. STnM [1:0]=01 and active edge set by the STnIO [1:0] bits 2. A STMn Capture input pin active edge transfers the counter value to CCRA 3. STnCCLR bit not used 4. No output function – STnOC and STnPOL bits are not used 5. CCRP determines the counter value and the counter has a maximum count value when CCRP is equal to zero. 6. n=0 ~ 2 Rev. 1.00 151 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Periodic Type TM – PTM The Periodic Type TM contains five operating modes, which are Compare Match Output, Timer/ Event Counter, Capture Input, Single Pulse Output and PWM Output modes. The Periodic TM can also be controlled with two external input pins and can drive two external output pin. Device HT67F2350 HT67F2360 HT67F2370 HT67F2390 PTM Core PTM Input Pin PTM Output Pin 10-bit PTM (PTM0, PTM1, PTM4, PTM5, PTM6, PTM7,) PTCK0, PTP0I PTCK1, PTP1I PTCK4, PTP4I PTCK5, PTP5I PTCK6, PTP6I PTCK7, PTP7I PTP0 PTP1 PTP4 PTP5 PTP6 PTP7 16-bit PTM (PTM2, PTM3) PTCK2, PTP2I PTCK3, PTP3I PTP2 PTP3 CCRP fSYS/4 fSYS fH/16 fH/64 fSUB fSUB 10-bit Comparator P 001 PTMnPF Interrupt PTnOC b0~b9 010 011 10-bit Count-up Counter 100 101 110 PTCKn Comparator P Match 000 PTnON PTnPAU Counter Clear PTnCCLR b0~b9 111 PTnCK2~PTnCK0 10-bit Comparator A CCRA Output Control Polarity Control Pin Control PTnM1, PTnM0 PTnIO1, PTnIO0 PTnPOL PxSn 0 1 Comparator A Match PTPn PTMnAF Interrupt IFS PTnIO1, PTnIO0 PTnCAPTS Edge Detector 0 Pin Control 1 PTPnI 10-bit Periodic Type TM Block Diagram – n=0, 1, 4, 5, 6 or 7 CCRP fSYS/4 fSYS fH/16 fH/64 fSUB fSUB 16-bit Comparator P 001 PTMnPF Interrupt PTnOC b0~b15 010 011 16-bit Count-up Counter 100 101 110 PTCKn Comparator P Match 000 PTnON PTnPAU Counter Clear PTnCCLR b0~b15 111 PTnCK2~PTnCK0 16-bit Comparator A CCRA Output Control Polarity Control Pin Control PTnM1, PTnM0 PTnIO1, PTnIO0 PTnPOL PxSn 0 1 Comparator A Match PTPn PTMnAF Interrupt IFS PTnIO1, PTnIO0 PTnCAPTS Edge Detector 0 1 Pin Control PTPnI 16-bit Periodic Type TM Block Diagram – n=2 or 3 Rev. 1.00 152 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Periodic TM Operation The size of Periodic Type TM is 10-/16-bit wide and its core is a 10-/16-bit count-up counter which is driven by a user selectable internal or external clock source. There are also two internal comparators with the names, Comparator A and Comparator P. These comparators will compare the value in the counter with CCRP and CCRA registers. The CCRP and CCRA comparators are 10-/16bit wide whose value is respectively compared with all counter bits. The only way of changing the value of the 10-/16-bit counter using the application program is to clear the counter by changing the PTnON bit from low to high. The counter will also be cleared automatically by a counter overflow or a compare match with one of its associated comparators. When these conditions occur, a PTM interrupt signal will also usually be generated. The Periodic Type TM can operate in a number of different operational modes, can be driven by different clock sources including an input pin and can also control the output pins. All operating setup conditions are selected using relevant internal registers. Periodic Type TM Register Description Overall operation of the Periodic TM is controlled using a series of registers. A read only register pair exists to store the internal counter 10-/16-bit value, while two read/write register pairs exist to store the internal 10-/16-bit CCRA and CCRP value. The remaining two registers are control registers which setup the different operating and control modes. Register Name Bit 7 6 5 4 3 2 1 0 PTnCK1 PTnCK0 PTnON — — — PTMnC0 PTnPAU PTnCK2 PTMnC1 PTnM1 PTnM0 PTnIO1 PTnIO0 PTnOC PTMnDL D7 D6 D5 D4 D3 D2 D1 PTMnDH — — — — — — D9 D8 PTMnAL D7 D6 D5 D4 D3 D2 D1 D0 PTMnAH — PTMnRPL PTnRP7 PTMnRPH — PTnPOL PTnCAPTS PTnCCLR D0 — — — — — D9 D8 PTnRP6 PTnRP5 PTnRP4 PTnRP3 PTnRP2 PTnRP1 PTnRP0 — — — — — PTnRP9 PTnRP8 10-bit Periodic TM Registers List – n=0, 1, 4, 5, 6 or 7 Bit Register Name 7 6 5 4 3 2 1 0 PTMnC0 PTnPAU PTnCK2 PTnCK1 PTnCK0 PTnON — — — PTMnC1 PTnM1 PTnM0 PTnIO1 PTnIO0 PTnOC PTMnDL D7 D6 D5 D4 D3 D2 PTMnDH D15 D14 D13 D12 D11 D10 D9 D8 PTMnAL D7 D6 D5 D4 D3 D2 D1 D0 PTMnAH D15 PTnPOL PTnCAPTS PTnCCLR D1 D0 D14 D13 D12 D11 D10 D9 D8 PTnRP6 PTnRP5 PTnRP4 PTnRP3 PTnRP2 PTnRP1 PTnRP0 PTMnRPH PTnRP15 PTnRP14 PTnRP13 PTnRP12 PTnRP11 PTnRP10 PTnRP9 PTnRP8 PTMnRPL PTnRP7 16-bit Periodic TM Registers List – n=2 or 3 Rev. 1.00 153 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM PTMnDL Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R R R R R R R R POR 0 0 0 0 0 0 0 0 Bit 7~0 PTMn Counter Low Byte Register bit 7 ~ bit 0 PTMn 10-/16-bit Counter bit 7 ~ bit 0 PTMnDH Register – n=0, 1, 4, 5, 6 or 7 Bit 7 6 5 4 3 2 1 0 Name — — — — — — D9 D8 R/W — — — — — — R R POR — — — — — — 0 0 Bit 7~2 Unimplemented, read as "0" Bit 1~0 PTMn Counter High Byte Register bit 1 ~ bit 0 PTMn 10-bit Counter bit 9 ~ bit 8 PTMnDH Register – n=2 or 3 Bit 7 6 5 4 3 2 1 0 Name D15 D14 D13 D12 D11 D10 D9 D8 R/W R R R R R R R R POR 0 0 0 0 0 0 0 0 Bit 7~0 PTMn Counter High Byte Register bit 7 ~ bit 0 PTMn 16-bit Counter bit 15 ~ bit 8 PTMnAL Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 PTMn CCRA Low Byte Register bit 7 ~ bit 0 PTMn 10-/16-bit CCRA bit 7 ~ bit 0 PTMnAH Register – n=0, 1, 4, 5, 6 or 7 Bit 7 6 5 4 3 2 1 0 Name — — — — — — D9 D8 R/W — — — — — — R/W R/W POR — — — — — — 0 0 Bit 7~2 Unimplemented, read as "0" Bit 1~0 PTMn CCRA High Byte Register bit 1 ~ bit 0 PTMn 10-bit CCRA bit 9 ~ bit 8 PTMnAH Register – n=2 or 3 Bit 7 6 5 4 3 2 1 0 Name D15 D14 D13 D12 D11 D10 D9 D8 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Rev. 1.00 PTMn CCRA High Byte Register bit 7 ~ bit 0 PTMn 16-bit CCRA bit 15 ~ bit 8 154 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM PTMnRPL Register Bit 7 6 5 4 3 2 1 0 Name PTnRP7 PTnRP6 PTnRP5 PTnRP4 PTnRP3 PTnRP2 PTnRP1 PTnRP0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 PTnRP7~PTnRP0: PTMn CCRP Low Byte Register bit 7 ~ bit 0 PTMn 10-/16-bit CCRP bit 7 ~ bit 0 PTMnRPH Register – n=0, 1, 4, 5, 6 or 7 Bit 7 6 5 4 3 2 1 0 Name — — — — — — PTnRP9 PTnRP8 R/W — — — — — — R/W R/W POR — — — — — — 0 0 Bit 7~2 Unimplemented, read as "0" Bit 1~0 PTnRP9~PTnRP8: PTMn CCRP High Byte Register bit 1 ~ bit 0 PTMn 10-bit CCRP bit 9 ~ bit 8 PTMnRPH Register – n=2 or 3 Bit Name 7 6 5 4 3 2 1 PTnRP15 PTnRP14 PTnRP13 PTnRP12 PTnRP11 PTnRP10 PTnRP9 0 PTnRP8 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 PTnRP15~PTnRP8: PTMn CCRP High Byte Register bit 7 ~ bit 0 PTMn 16-bit CCRP bit 15 ~ bit 8 PTMnC0 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name PTnPAU PTnCK2 PTnCK1 PTnCK0 PTnON — — — R/W R/W R/W R/W R/W R/W — — — POR 0 0 0 0 0 — — — Bit 7 PTnPAU: PTMn Counter Pause control 0: Run 1: Pause The counter can be paused by setting this bit high. Clearing the bit to zero restores normal counter operation. When in a Pause condition the PTMn will remain powered up and continue to consume power. The counter will retain its residual value when this bit changes from low to high and resume counting from this value when the bit changes to a low value again. Bit 6~4 PTnCK2~PTnCK0: Select PTMn Counter clock 000: fSYS/4 001: fSYS 010: fH/16 011: fH/64 100: fSUB 101: fSUB 110: PTCKn rising edge clock 111: PTCKn falling edge clock These three bits are used to select the clock source for the PTMn. The external pin clock source can be chosen to be active on the rising or falling edge. The clock source fSYS is the system clock, while fH and fSUB are other internal clocks, the details of which can be found in the oscillator section. 155 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 3 PTnON: PTMn Counter On/Off control 0: Off 1: On This bit controls the overall on/off function of the PTMn. Setting the bit high enables the counter to run while clearing the bit disables the PTMn. Clearing this bit to zero will stop the counter from counting and turn off the PTMn which will reduce its power consumption. When the bit changes state from low to high the internal counter value will be reset to zero, however when the bit changes from high to low, the internal counter will retain its residual value until the bit returns high again. If the PTMn is in the Compare Match Output Mode then the PTMn output pin will be reset to its initial condition, as specified by the PTnOC bit, when the PTnON bit changes from low to high. Bit 2~0 Unimplemented, read as "0" PTMnC1 Register Rev. 1.00 Bit 7 6 5 4 3 Name PTnM1 PTnM0 PTnIO1 PTnIO0 PTnOC 2 1 0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 PTnPOL PTnCAPTS PTnCCLR Bit 7~6 PTnM1~PTnM0: Select PTMn Operating Mode 00: Compare Match Output Mode 01: Capture Input Mode 10: PWM Output Mode or Single Pulse Output Mode 11: Timer/Counter Mode These bits setup the required operating mode for the PTMn. To ensure reliable operation the PTMn should be switched off before any changes are made to the PTnM1 and PTnM0 bits. In the Timer/Counter Mode, the PTMn output pin control will be disabled. Bit 5~4 PTnIO1~PTnIO0: Select PTMn external pin PTPn or PTPnI function Compare Match Output Mode 00: No change 01: Output low 10: Output high 11: Toggle output PWM Output Mode/Single Pulse Output Mode 00: PWM output inactive state 01: PWM output active state 10: PWM output 11: Single Pulse Output Capture Input Mode 00: Input capture at rising edge of PTPnI or PTCKn 01: Input capture at falling edge of PTPnI or PTCKn 10: Input capture at rising/falling edge of PTPnI or PTCKn 11: Input capture disabled Timer/Counter Mode Unused These two bits are used to determine how the PTMn output pin changes state when a certain condition is reached. The function that these bits select depends upon in which mode the PTMn is running. 156 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM In the Compare Match Output Mode, the PTnIO1 and PTnIO0 bits determine how the PTMn output pin changes state when a compare match occurs from the Comparator A. The PTMn output pin can be setup to switch high, switch low or to toggle its present state when a compare match occurs from the Comparator A. When the bits are both zero, then no change will take place on the output. The initial value of the PTMn output pin should be setup using the PTnOC bit in the PTMnC1 register. Note that the output level requested by the PTnIO1 and PTnIO0 bits must be different from the initial value setup using the PTnOC bit otherwise no change will occur on the PTMn output pin when a compare match occurs. After the PTMn output pin changes state, it can be reset to its initial level by changing the level of the PTnON bit from low to high. In the PWM Output Mode, the PTnIO1 and PTnIO0 bits determine how the TM output pin changes state when a certain compare match condition occurs. The PTMn output function is modified by changing these two bits. It is necessary to only change the values of the PTnIO1 and PTnIO0 bits only after the PTMn has been switched off. Unpredictable PWM outputs will occur if the PTnIO1 and PTnIO0 bits are changed when the PTMn is running. Rev. 1.00 Bit 3 PTnOC: PTMn PTPn Output control Compare Match Output Mode 0: Initial low 1: Initial high PWM Output Mode/Single Pulse Output Mode 0: Active low 1: Active high This is the output control bit for the PTMn output pin. Its operation depends upon whether PTMn is being used in the Compare Match Output Mode or in the PWM Output Mode/Single Pulse Output Mode. It has no effect if the PTMn is in the Timer/ Counter Mode. In the Compare Match Output Mode it determines the logic level of the PTMn output pin before a compare match occurs. In the PWM Output Mode/Single Pulse Output Mode it determines if the PWM signal is active high or active low. Bit 2 PTnPOL: PTMn PTPn Output polarity control 0: Non-inverted 1: Inverted This bit controls the polarity of the PTPn output pin. When the bit is set high the PTMn output pin will be inverted and not inverted when the bit is zero. It has no effect if the PTMn is in the Timer/Counter Mode. Bit 1 PTnCAPTS: PTMn Capture Trigger Source selection 0: From PTPnI pin 1: From PTCKn pin Bit 0 PTnCCLR: PTMn Counter Clear condition selection 0: Comparator P match 1: Comparator A match This bit is used to select the method which clears the counter. Remember that the Periodic TM contains two comparators, Comparator A and Comparator P, either of which can be selected to clear the internal counter. With the PTnCCLR bit set high, the counter will be cleared when a compare match occurs from the Comparator A. When the bit is low, the counter will be cleared when a compare match occurs from the Comparator P or with a counter overflow. A counter overflow clearing method can only be implemented if the CCRP bits are all cleared to zero. The PTnCCLR bit is not used in the PWM Output, Single Pulse Output or Capture Input Mode. 157 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Periodic Type TM Operation Modes The Periodic Type TM can operate in one of five operating modes, Compare Match Output Mode, PWM Output Mode, Single Pulse Output Mode, Capture Input Mode or Timer/Counter Mode. The operating mode is selected using the PTnM1 and PTnM0 bits in the PTMnC1 register. Compare Match Output Mode To select this mode, bits PTnM1 and PTnM0 in the PTMnC1 register, should be set to 00 respectively. In this mode once the counter is enabled and running it can be cleared by three methods. These are a counter overflow, a compare match from Comparator A and a compare match from Comparator P. When the PTnCCLR bit is low, there are two ways in which the counter can be cleared. One is when a compare match from Comparator P, the other is when the CCRP bits are all zero which allows the counter to overflow. Here both PTMnAF and PTMnPF interrupt request flags for Comparator A and Comparator P respectively, will both be generated. If the PTnCCLR bit in the PTMnC1 register is high then the counter will be cleared when a compare match occurs from Comparator A. However, here only the PTMnAF interrupt request flag will be generated even if the value of the CCRP bits is less than that of the CCRA registers. Therefore when PTnCCLR is high no PTMnPF interrupt request flag will be generated. In the Compare Match Output Mode, the CCRA can not be set to "0". As the name of the mode suggests, after a comparison is made, the PTMn output pin will change state. The PTMn output pin condition however only changes state when a PTMnAF interrupt request flag is generated after a compare match occurs from Comparator A. The PTMnPF interrupt request flag, generated from a compare match occurs from Comparator P, will have no effect on the PTMn output pin. The way in which the PTMn output pin changes state are determined by the condition of the PTnIO1 and PTnIO0 bits in the PTMnC1 register. The PTMn output pin can be selected using the PTnIO1 and PTnIO0 bits to go high, to go low or to toggle from its present condition when a compare match occurs from Comparator A. The initial condition of the PTMn output pin, which is setup after the PTnON bit changes from low to high, is setup using the PTnOC bit. Note that if the PTnIO1 and PTnIO0 bits are zero then no pin change will take place. Rev. 1.00 158 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� ove�flow Counte� Value 0x3FF PTnCCLR = 0; PTnM [1:0] = 00 CCRP > 0 Counte� �lea�ed �y CCRP value CCRP=0 CCRP > 0 Counte� Resta�t Resu�e CCRP Pause CCRA Stop Ti�e PTnON PTnPAU PTnPOL CCRP Int. Flag PTMnPF CCRA Int. Flag PTMnAF PTMn O/P Pin Output pin set to initial Level Low if PTnOC=0 Output not affe�ted �y PTMnAF flag. Re�ains High until �eset �y PTnON �it Output Toggle with PTMnAF flag He�e PTnIO [1:0] = 11 Toggle Output sele�t Note PTnIO [1:0] = 10 A�tive High Output sele�t Output Inve�ts when PTnPOL is high Output Pin Reset to Initial value Output �ont�olled �y othe� pin-sha�ed fun�tion Compare Match Output Mode – PTnCCLR=0 Note: 1. With PTnCCLR=0, a Comparator P match will clear the counter 2. The PTMn output pin is controlled only by the PTMnAF flag 3. The output pin is reset to its initial state by a PTnON bit rising edge 4. The 10-bit PTM maximum counter value is 0x3FF while the 16-bit PTM maximum counter value is 0xFFFF. 5. n=0, 1, 4, 5, 6 or 7 for 10-bit PTM while n=2 or 3 for 16-bit PTM Rev. 1.00 159 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value PTnCCLR = 1; PTnM [1:0] = 00 CCRA = 0 Counte� ove�flow CCRA > 0 Counte� �lea�ed �y CCRA value 0x3FF CCRA=0 Resu�e CCRA Pause Stop Counte� Resta�t CCRP Ti�e PTnON PTnPAU PTnPOL No PTMnAF flag gene�ated on CCRA ove�flow CCRA Int. Flag PTMnAF CCRP Int. Flag PTMnPF PTMn O/P Pin PTMnPF not gene�ated Output pin set to initial Level Low if PTnOC=0 Output does not �hange Output Toggle with PTMnAF flag He�e PTnIO [1:0] = 11 Toggle Output sele�t Output not affe�ted �y PTMnAF flag. Re�ains High until �eset �y PTnON �it Note PTnIO [1:0] = 10 A�tive High Output sele�t Output Inve�ts when PTnPOL is high Output Pin Reset to Initial value Output �ont�olled �y othe� pin-sha�ed fun�tion Compare Match Output Mode – PTnCCLR=1 Note: 1. With PTnCCLR=1, a Comparator A match will clear the counter 2. The PTMn output pin is controlled only by the PTMnAF flag 3. The output pin is reset to its initial state by a PTnON bit rising edge 4. A PTMnPF flag is not generated when PTnCCLR =1 5. The 10-bit PTM maximum counter value is 0x3FF while the 16-bit PTM maximum counter value is 0xFFFF. 6. n=0, 1, 4, 5, 6 or 7 for 10-bit PTM while n=2 or 3 for 16-bit PTM Rev. 1.00 160 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Timer/Counter Mode To select this mode, bits PTnM1 and PTnM0 in the PTMnC1 register should be set to 11 respectively. The Timer/Counter Mode operates in an identical way to the Compare Match Output Mode generating the same interrupt flags. The exception is that in the Timer/Counter Mode the PTMn output pin is not used. Therefore the above description and Timing Diagrams for the Compare Match Output Mode can be used to understand its function. As the PTMn output pin is not used in this mode, the pin can be used as a normal I/O pin or other pin-shared function. PWM Output Mode To select this mode, bits PTnM1 and PTnM0 in the PTMnC1 register should be set to 10 respectively and also the PTnIO1 and PTnIO0 bits should be set to 10 respectively. The PWM function within the PTMn is useful for applications which require functions such as motor control, heating control, illumination control, etc. By providing a signal of fixed frequency but of varying duty cycle on the PTMn output pin, a square wave AC waveform can be generated with varying equivalent DC RMS values. As both the period and duty cycle of the PWM waveform can be controlled, the choice of generated waveform is extremely flexible. In the PWM mode, the PTnCCLR bit has no effect as the PWM period. Both of the CCRP and CCRA registers are used to generate the PWM waveform, one register is used to clear the internal counter and thus control the PWM waveform frequency, while the other one is used to control the duty cycle. The PWM waveform frequency and duty cycle can therefore be controlled by the values in the CCRA and CCRP registers. As both the period and duty cycle of the PWM waveform can be controlled, the choice of generated waveform is extremely flexible. In the PWM Output mode, the PTnCCLR bit has no effect as the PWM period. Both of the CCRP and CCRA registers are used to generate the PWM waveform, one register is used to clear the internal counter and thus control the PWM waveform frequency, while the other one is used to control the duty cycle. The PWM waveform frequency and duty cycle can therefore be controlled by the values in the CCRA and CCRP registers. • 16-bit PTMn, PWM Output Mode, CCRP 1~65535 0 Period 1~65535 65536 Duty CCRA If fSYS=16MHz, TM clock source select fSYS/4, CCRP=512 and CCRA=128, The PTMn PWM output frequency=(fSYS/4)/512=fSYS/2048=8kHz, duty=128/512=25%, If the Duty value defined by the CCRA register is equal to or greater than the Period value, then the PWM output duty is 100%. Rev. 1.00 161 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value PTnM [1:0] = 10 Counte� �lea�ed �y CCRP Counte� Reset when PTnON �etu�ns high CCRP Pause Resu�e Counte� Stop if PTnON �it low CCRA Ti�e PTnON PTnPAU PTnPOL CCRA Int. Flag PTMnAF CCRP Int. Flag PTMnPF PTMn O/P Pin (PTnOC=1) PTMn O/P Pin (PTnOC=0) PWM Duty Cy�le set �y CCRA PWM �esu�es ope�ation Output �ont�olled �y othe� pin-sha�ed fun�tion PWM Pe�iod set �y CCRP Output Inve�ts When PTnPOL = 1 PWM Output Mode Note: 1. The counter is cleared by CCRP. 2. A counter clear sets the PWM Period 3. The internal PWM function continues running even when PTnIO [1:0]=00 or 01 4. The PTnCCLR bit has no influence on PWM operation 5. n=0, 1, 4, 5, 6 or 7 for 10-bit PTM while n=2 or 3 for 16-bit PTM Rev. 1.00 162 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Single Pulse Output Mode To select this mode, bits PTnM1 and PTnM0 in the PTMnC1 register should be set to 10 respectively and also the PTnIO1 and PTnIO0 bits should be set to 11 respectively. The Single Pulse Output Mode, as the name suggests, will generate a single shot pulse on the PTMn output pin. The trigger for the pulse output leading edge is a low to high transition of the PTnON bit, which can be implemented using the application program. However in the Single Pulse Output Mode, the PTnON bit can also be made to automatically change from low to high using the external PTCKn pin, which will in turn initiate the Single Pulse output. When the PTnON bit transitions to a high level, the counter will start running and the pulse leading edge will be generated. The PTnON bit should remain high when the pulse is in its active state. The generated pulse trailing edge will be generated when the PTnON bit is cleared to zero, which can be implemented using the application program or when a compare match occurs from Comparator A. However a compare match from Comparator A will also automatically clear the PTnON bit and thus generate the Single Pulse output trailing edge. In this way the CCRA value can be used to control the pulse width. A compare match from Comparator A will also generate a PTMn interrupt. The counter can only be reset back to zero when the PTnON bit changes from low to high when the counter restarts. In the Single Pulse Output Mode CCRP is not used. The PTnCCLR is not used in this Mode. S/W Command SET“PTnON” or PTCKn Pin Transition CCRA Leading Edge CCRA Trailing Edge PTnON bit 0à1 PTnON bit 1à0 S/W Command CLR“PTnON” or CCRA Compare Match PTPn Output Pin Pulse Width = CCRA Value Single Pulse Generation Rev. 1.00 163 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value PTnM [1:0] = 10 ; PTnIO [1:0] = 11 Counte� stopped �y CCRA Counte� Reset when PTnON �etu�ns high CCRA Pause Counte� Stops �y softwa�e Resu�e CCRP Ti�e PTnON Softwa�e T�igge� Clea�ed �y CCRA �at�h Auto. set �y PTCKn pin Softwa�e T�igge� Softwa�e T�igge� Softwa�e Clea� Softwa�e T�igge� PTCKn pin PTCKn pin T�igge� PTnPAU PTnPOL CCRP Int. Flag PTMnPF No CCRP Inte��upts gene�ated CCRA Int. Flag PTMnAF PTMn O/P Pin (PTnOC=1) PTMn O/P Pin (PTnOC=0) Output Inve�ts when PTnPOL = 1 Pulse Width set �y CCRA Single Pulse Output Mode Note: 1. Counter stopped by CCRA 2. CCRP is not used 3. The pulse triggered by the PTCKn pin or by setting the PTnON bit high 4. A PTCKn pin active edge will automatically set the PTnON bit high. 5. In the Single Pulse Output Mode, PTnIO [1:0] must be set to "11" and can not be changed. 6. n=0, 1, 4, 5, 6 or 7 for 10-bit PTM while n=2 or 3 for 16-bit PTM Rev. 1.00 164 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Capture Input Mode To select this mode bits PTnM1 and PTnM0 in the PTMnC1 register should be set to 01 respectively. This mode enables external signals to capture and store the present value of the internal counter and can therefore be used for applications such as pulse width measurements. The external signal is supplied on the PTPnI or PTCKn pin, selected by the PTnCAPTS bit in the PTMnC1 register. The input pin active edge can be either a rising edge, a falling edge or both rising and falling edges; the active edge transition type is selected using the PTnIO1 and PTnIO0 bits in the PTMnC1 register. The counter is started when the PTnON bit changes from low to high which is initiated using the application program. When the required edge transition appears on the PTPnI or PTCKn pin the present value in the counter will be latched into the CCRA registers and a PTMn interrupt generated. Irrespective of what events occur on the PTPnI or PTCKn pin the counter will continue to free run until the PTnON bit changes from high to low. When a CCRP compare match occurs the counter will reset back to zero; in this way the CCRP value can be used to control the maximum counter value. When a CCRP compare match occurs from Comparator P, a PTMn interrupt will also be generated. Counting the number of overflow interrupt signals from the CCRP can be a useful method in measuring long pulse widths. The PTnIO1 and PTnIO0 bits can select the active trigger edge on the PTPnI or PTCKn pin to be a rising edge, falling edge or both edge types. If the PTnIO1 and PTnIO0 bits are both set high, then no capture operation will take place irrespective of what happens on the PTPnI or PTCKn pin, however it must be noted that the counter will continue to run. As the PTPnI or PTCKn pin is pin shared with other functions, care must be taken if the PTMn is in the Input Capture Mode. This is because if the pin is setup as an output, then any transitions on this pin may cause an input capture operation to be executed. The PTnCCLR, PTnOC and PTnPOL bits are not used in this Mode. Rev. 1.00 165 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Counte� Value PTnM[1:0] = 01 Counte� �lea�ed �y CCRP Counte� Stop Counte� Reset CCRP Resu�e YY Pause XX Ti�e PTnON PTnPAU A�tive edge A�tive edge A�tive edge PTMn Captu�e Pin PTPnI o� PTCKn CCRA Int. Flag PTMnAF CCRP Int. Flag PTMnPF CCRA Value PTnIO [1:0] Value XX 00 - Rising edge YY 01 - Falling edge XX 10 - Both edges YY 11 - Disa�le Captu�e Capture Input Mode Note: 1. PTnM [1:0]=01 and active edge set by the PTnIO [1:0] bits 2. A PTMn Capture input pin active edge transfers the counter value to CCRA 3. PTnCCLR bit not used 4. No output function – PTnOC and PTnPOL bits are not used 5. CCRP determines the counter value and the counter has a maximum count value when CCRP is equal to zero. 6. n=0, 1, 4, 5, 6 or 7 for 10-bit PTM while n=2 or 3 for 16-bit PTM Rev. 1.00 166 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Analog to Digital Converter The need to interface to real world analog signals is a common requirement for many electronic systems. However, to properly process these signals by a microcontroller, they must first be converted into digital signals by A/D converters. By integrating the A/D conversion electronic circuitry into the microcontroller, the need for external components is reduced significantly with the corresponding follow-on benefits of lower costs and reduced component space requirements. A/D Overview These devices contain a multi-channel analog to digital converter which can directly interface to external analog signals, such as that from sensors or other control signals and convert these signals directly into a 12-bit digital value. It also can convert the internal signals, such as the internal reference voltage, into a 12-bit digital value. The external or internal analog signal to be converted is determined by the SAINS and SACS bit fields. Note that when the internal analog signal is selected to be converted using the SAINS field, the external channel analog input will automatically be switched off. More detailed information about the A/D input signal selection will be described in the "A/D Converter Input Signals" section. The accompanying block diagram shows the internal structure of the A/D converter with temperature sensor together with its associated registers and control bits. Device External Input Channels HT67F2350 AN0~AN11 HT67F2360 HT67F2370 HT67F2390 AN0~AN15 Internal Signal A/D Signal Select AVDD, AVDD/2, AVDD/4, VR, VR/2, VR/4, SAINS3~SAINS0 SACS3~SACS0 AVDD fSYS Pin-sha�ed Sele�tion SACS3~SACS0 ÷ �N SACKS�~ SACKS0 AN0 AN1 ADCEN (N=0~7) AVSS A/D Clo�k AN15 SAINS3~SAINS0 SAINS3~SAINS0 AVDD AVDD/� AVDD/4 VR VR/� VR/4 AVSS SADOL A/D Conve�te� AN11 START ADBZ ADCEN ADRFS SADOH A/D Data Registe�s A/D Conve�te� Refe�en�e Voltage SAVRS1~SAVRS0 ADPGAEN PGAIS VBGREF VREFI VREFI Pin-sha�ed Sele�tion VRI PGA VR VREF AVDD PGAS1~PGAS0 (Gain=1� 1.��7� �.5� 3.333) VREF Pin-sha�ed Sele�tion Note: The external channel is from AN0 to AN11 for the HT67F2350 device. A/D Converter Structure Rev. 1.00 167 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Registers Descriptions Overall operation of the A/D converter is controlled using six registers. A read only register pair exists to store the A/D Converter data 12-bit value. Three registers, SADC0, SADC1 and SADC2, are the control registers which setup the operating conditions and control function of the A/D converter. The VBGRC register contains the VBGREN bit to control the bandgap reference voltage. Bit Register Name 7 6 5 4 3 2 1 0 SADOL (ADRFS=0) D3 D2 D1 D0 — — — — SADOL (ADRFS=1) D7 D6 D5 D4 D3 D2 D1 D0 S ADOH (ADRFS=0) D11 D10 D9 D8 D7 D6 D5 D4 SADOH (ADRFS=1) — — — — D11 D10 D9 D8 SADC0 START ADBZ ADCEN ADRFS SACS3 SACS2 SACS1 SACS0 SADC1 SAINS3 SAINS2 SAINS1 SAINS0 — SACKS2 SACKS1 SACKS0 SADC2 ADPGAEN — — PGAIS SAVRS1 SAVRS0 PGAGS1 PGAGS0 VBGRC — — — — — — — VBGREN A/D Converter Registers List A/D Converter Data Registers – SADOL, SADOH As these devices contain an internal 12-bit A/D converter, it requires two data registers to store the converted value. These are a high byte register, known as SADOH, and a low byte register, known as SADOL. After the conversion process takes place, these registers can be directly read by the microcontroller to obtain the digitised conversion value. As only 12 bits of the 16-bit register space is utilised, the format in which the data is stored is controlled by the ADRFS bit in the SADC0 register as shown in the accompanying table. D0~D11 are the A/D conversion result data bits. Any unused bits will be read as zero. The A/D data registers contents will be unchanged if the A/D converter is disabled. SADOH ADRFS SADOL 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 0 0 0 0 1 0 0 0 0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 A/D Converter Data Registers A/D Converter Control Registers – SADC0, SADC1, SADC2 To control the function and operation of the A/D converter, three control registers known as SADC0, SADC1 and SADC2 are provided. These 8-bit registers define functions such as the selection of which analog signal is connected to the internal A/D converter, the digitised data format, the A/D clock source as well as controlling the start function and monitoring the A/D converter busy status. As these devices contain only one actual analog to digital converter hardware circuit, each of the external and internal analog signals must be routed to the converter. The SAINS field in the SADC1 register and SACS field in the SADC0 register are used to determine which analog signal derived from the external or internal signals will be connected to the A/D converter. The A/D converter also contains a programmable gain amplifier, PGA, to generate the A/D converter internal reference voltage. The overall operation of the PGA is controlled using the SADC2 register. Rev. 1.00 168 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM The relevant pin-shared function selection bits determine which pins on I/O Ports are used as analog inputs for the A/D converter input and which pins are not. When the pin is selected to be an A/D input, its original function whether it is an I/O or other pin-shared function will be removed. In addition, any internal pull-high resistor connected to the pin will be automatically removed if the pin is selected to be an A/D converter input. • SADC0 Register – HT67F2350 Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name START ADBZ ADCEN ADRFS SACS3 SACS2 SACS1 SACS0 R/W R/W R R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 START: Start the A/D Conversion 0→1→0: Start This bit is used to initiate an A/D conversion process. The bit is normally low but if set high and then cleared low again, the A/D converter will initiate a conversion process. Bit 6 ADBZ: A/D Converter busy flag 0: No A/D conversion is in progress 1: A/D conversion is in progress This read only flag is used to indicate whether the A/D conversion is in progress or not. When the START bit is set from low to high and then to low again, the ADBZ flag will be set to 1 to indicate that the A/D conversion is initiated. The ADBZ flag will be cleared to 0 after the A/D conversion is complete. Bit 5 ADCEN: A/D Converter function enable control 0: Disable 1: Enable This bit controls the A/D internal function. This bit should be set to one to enable the A/D converter. If the bit is set low, then the A/D converter will be switched off reducing the device power consumption. When the A/D converter function is disabled, the contents of the A/D data register pair known as SADOH and SADOL will be unchanged. Bit 4 ADRFS: A/D conversion data format select 0: A/D converter data format → SADOH=D [11:4]; SADOL=D [3:0] 1: A/D converter data format → SADOH=D [11:8]; SADOL=D [7:0] This bit controls the format of the 12-bit converted A/D value in the two A/D data registers. Details are provided in the A/D converter data register section. Bit 3~0 SACS3~SACS0: A/D converter external analog input channel select 0000: External AN0 input 0001: External AN1 input 0010: External AN2 input 0011: External AN3 input 0100: External AN4 input 0101: External AN5 input 0110: External AN6 input 0111: External AN7 input 1000: External AN8 input 1001: External AN9 input 1010: External AN10 input 1011: External AN11 input 11xx: Undefined, input floating. These bits are used to select which external analog input channel is to be converted. When the external analog input channel is selected, the SAINS bit field must set to "0000", "0100" or "11xx". Details are summarized in the "A/D Converter Input Signal Selection" table. 169 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • SADC0 Register – HT67F2360/HT67F2370/HT67F2390 Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name START ADBZ ADCEN ADRFS SACS3 SACS2 SACS1 SACS0 R/W R/W R R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 START: Start the A/D Conversion 0→1→0: Start This bit is used to initiate an A/D conversion process. The bit is normally low but if set high and then cleared low again, the A/D converter will initiate a conversion process. Bit 6 ADBZ: A/D Converter busy flag 0: No A/D conversion is in progress 1: A/D conversion is in progress This read only flag is used to indicate whether the A/D conversion is in progress or not. When the START bit is set from low to high and then to low again, the ADBZ flag will be set to 1 to indicate that the A/D conversion is initiated. The ADBZ flag will be cleared to 0 after the A/D conversion is complete. Bit 5 ADCEN: A/D Converter function enable control 0: Disable 1: Enable This bit controls the A/D internal function. This bit should be set to one to enable the A/D converter. If the bit is set low, then the A/D converter will be switched off reducing the device power consumption. When the A/D converter function is disabled, the contents of the A/D data register pair known as SADOH and SADOL will be unchanged. Bit 4 ADRFS: A/D conversion data format select 0: A/D converter data format → SADOH=D [11:4]; SADOL=D [3:0] 1: A/D converter data format → SADOH=D [11:8]; SADOL=D [7:0] This bit controls the format of the 12-bit converted A/D value in the two A/D data registers. Details are provided in the A/D converter data register section. Bit 3~0 SACS3~SACS0: A/D converter external analog input channel select 0000: External AN0 input 0001: External AN1 input 0010: External AN2 input 0011: External AN3 input 0100: External AN4 input 0101: External AN5 input 0110: External AN6 input 0111: External AN7 input 1000: External AN8 input 1001: External AN9 input 1010: External AN10 input 1011: External AN11 input 1100: External AN12 input 1101: External AN13 input 1110: External AN14 input 1111: External AN15 input These bits are used to select which external analog input channel is to be converted. When the external analog input channel is selected, the SAINS bit field must set to "0000", "0100" or "11xx". Details are summarized in the "A/D Converter Input Signal Selection" table. 170 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • SADC1 Register Bit 7 6 5 4 3 2 1 0 Name SAINS3 SAINS2 SAINS1 SAINS0 — SACKS2 SACKS1 SACKS0 R/W R/W R/W R/W R/W — R/W R/W R/W POR 0 0 0 0 — 0 0 0 Bit 7~4 SAINS3~SAINS0: A/D converter input signal select 0000: External source – External analog channel intput, ANn 0001: Internal source – Internal signal derived from AVDD 0010: Internal source – Internal signal derived from AVDD/2 0011: Internal source – Internal signal derived from AVDD/4 0100: External source – External analog channel intput, ANn 0101: Internal source – Internal signal derived from PGA output VR 0110: Internal source – Internal signal derived from PGA output VR/2 0111: Internal source – Internal signal derived from PGA output VR/4 10xx: Internal source – Ground. 11xx: External source – External analog channel intput, ANn When the internal analog signal is selected to be converted, the external channel signal input will automatically be switched off regardless of the SACS field value. It will prevent the external channel input from being connected together with the internal analog signal. Bit 3 Unimplemented, read as "0" Bit 2~0 SACKS2~SACKS0: A/D conversion clock source select 000: fSYS 001: fSYS/2 010: fSYS/4 011: fSYS/8 100: fSYS/16 101: fSYS/32 110: fSYS/64 111: fSYS/128 These bits are used to select the clock source for the A/D converter. It is recommended that the A/D conversion clock frequency should be in the range from 500 kHz to 1MHz by properly configuring the SACKS2~SACKS0 bits. • SADC2 Register Bit 7 6 5 4 3 2 Name ADPGAEN — — PGAIS SAVRS1 SAVRS0 R/W R/W — — R/W R/W R/W R/W R/W POR 0 — — 0 0 0 0 0 Bit 7 Rev. 1.00 1 0 PGAGS1 PGAGS0 ADPGAEN: PGA enable control 0: Disable 1: Enable Bit 6~5 Unimplemented, read as "0" Bit 4 PGAIS: PGA input voltage selection 0: From VREFI pin 1: From internal reference voltage VBGREF Bit 3~2 SAVRS1~SAVRS0: A/D converter reference voltage select 00: Internal A/D converter power, AVDD. 01: External VREF pin 1x: Internal PGA output voltage, VR. These bits are used to select the A/D converter reference voltage source. When the internal reference voltage source is selected, the reference voltage derived from the external VREF pin will automatically be switched off. 171 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 1~0 PGAGS1~PGAGS0: PGA gain select 00: Gain=1 01: Gain=1.667 – VR=2V as VRI=1.2V 10: Gain=2.5 – VR=3V as VRI=1.2V 11: Gain=3.333 – VR=4V as VRI=1.2V These bits are used to select the PGA gain. Note that here the gain is guaranteed only when the PGA input voltage is equal to 1.2V. • VBGRC Register Bit 7 6 5 4 3 2 1 0 Name — — — — — — — VBGREN R/W — — — — — — — R/W POR — — — — — — — 0 Bit 7~1 Unimplemented, read as "0" Bit 0 VBGREN: Bandgap reference voltage control 0: Disable 1: Enable This bit is used to enable the internal Bandgap reference circuit. The internal Bandgap reference circuit should first be enabled before the VBGREF voltage is selected to be used. A specific start-up time is necessary for the Bandgap circuit to become stable and accurate. A/D Converter Reference Voltage The actual reference voltage supply to the A/D Converter can be supplied from the positive power supply pin, AVDD, an external reference source supplied on pin VREF or an internal reference voltage VR determined by the SAVRS1~SAVRS0 bits in the SADC2 register. The internal reference voltage is amplified through a programmable gain amplifier, PGA, which is controlled by the ADPGAEN bit in the SADC2 register. The PGA gain can be equal to 1, 1.667, 2.5 or 3.333 and selected using the PGAGS1~PGAGS0 bits in the SADC2 register. The PGA input can come from the external reference input pin, VREFI, or an internal Bandgap reference voltage, VBGREF, selected by the PGAIS bit in the SADC2 register. As the VREFI and VREF pin both are pin-shared with other functions, when the VREFI or VREF pin is selected as the reference voltage pin, the VREFI or VREF pin-shared function selection bits should first be properly configured to disable other pin-shared functions. However, if the internal reference signal is selected as the reference source, the external reference input from the VREFI or VREF pin will automatically be switched off by hardware. Note that the internal Bandgap reference circuit should first be enabled before the VBGREF is selected to be used. A specific start-up time is necessary for the Bandgap circuit to become stable and accurate. Rev. 1.00 172 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM A/D Converter Input Signals All of the external A/D analog input pins are pin-shared with the I/O pins as well as other functions. The corresponding pin-shared function selection bits in the PxS1 and PxS0 registers, determine whether the external input pins are setup as A/D converter analog channel inputs or whether they have other functions. If the corresponding pin is setup to be an A/D converter analog channel input, the original pin function will be disabled. In this way, pins can be changed under program control to change their function between A/D inputs and other functions. All pull-high resistors, which are setup through register programming, will be automatically disconnected if the pins are setup as A/D inputs. Note that it is not necessary to first setup the A/D pin as an input in the port control register to enable the A/D input as when the relevant A/D input function selection bits enable an A/D input, the status of the port control register will be overridden. As these devices contain only one actual analog to digital converter hardware circuit, each of the external and internal analog signals must be routed to the converter. The SAINS3~SAINS0 bits in the SADC1 register are used to determine that the analog signal to be converted comes from the external channel input or internal analog signal. The SACS3~SACS0 bits in the SADC0 register are used to determine which external channel input is selected to be converted. If the SAINS3~SAINS0 bits are set to "0000", the external channel input will be selected to be converted and the SACS3~SACS0 bits can determine which external channel is selected. When the SAINS field is set to the value of "0x01", "0x10" or "0x11", the internal analog signal will be selected. If the internal analog signal is selected to be converted, the external channel signal input will automatically be switched off regardless of the SACS field value. It will prevent the external channel input from being connected together with the internal analog signal. SAINS [3:0] SACS [3:0] Input Signals 0000, 0100, 11xx 0000~1011 AN0~AN11 Description 11xx — 0001 xxxx AVDD 0010 xxxx AVDD/2 Internal signal derived from AVDD/2 0011 xxxx AVDD/4 Internal signal derived from AVDD/4 0101 xxxx VR 0110 xxxx VR/2 Internal signal derived from PGA output VR/2 0111 xxxx VR/4 Internal signal derived from PGA output VR/4 10xx xxxx GND Connected to the ground. External channel analog input ANn. Floating, no external channel is selected. Internal signal derived from AVDD Internal signal derived from PGA output VR A/D Converter Input Signal Selection – HT67F2350 SAINS [3:0] SACS [3:0] Input Signals 0000, 0100, 11xx Description 0000~1111 AN0~AN15 0001 xxxx AVDD 0010 xxxx AVDD/2 Internal signal derived from AVDD/2 0011 xxxx AVDD/4 Internal signal derived from AVDD/4 0101 xxxx VR 0110 xxxx VR/2 Internal signal derived from PGA output VR/2 0111 xxxx VR/4 Internal signal derived from PGA output VR/4 10xx xxxx GND Connected to the ground. External channel analog input ANn Internal signal derived from AVDD Internal signal derived from PGA output VR A/D Converter Input Signal Selection – HT67F2360/HT67F2370/HT67F2390 Rev. 1.00 173 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM A/D Operation The START bit in the SADC0 register is used to start the AD conversion. When the microcontroller sets this bit from low to high and then low again, an analog to digital conversion cycle will be initiated. The ADBZ bit in the SADC0 register is used to indicate whether the analog to digital conversion process is in progress or not. This bit will be automatically set to 1 by the microcontroller after an A/D conversion is successfully initiated. When the A/D conversion is complete, the ADBZ bit will be cleared to 0. In addition, the corresponding A/D interrupt request flag will be set in the interrupt control register, and if the interrupts are enabled, an internal interrupt signal will be generated. This A/D internal interrupt signal will direct the program flow to the associated A/D internal interrupt address for processing. If the A/D internal interrupt is disabled, the microcontroller can poll the ADBZ bit in the SADC0 register to check whether it has been cleared as an alternative method of detecting the end of an A/D conversion cycle. The clock source for the A/D converter, which originates from the system clock fSYS, can be chosen to be either fSYS or a subdivided version of fSYS. The division ratio value is determined by the SACKS2~SACKS0 bits in the SADC1 register. Although the A/D clock source is determined by the system clock fSYS and by bits SACKS2~SACKS0, there are some limitations on the maximum A/D clock source speed that can be selected. As the recommended range of permissible A/D clock period, tADCK, is from 0.5μs to 10μ, care must be taken for system clock frequencies. For example, if the system clock operates at a frequency of 8MHz, the SACKS2~SACKS0 bits should not be set to 000, 001 or 111. Doing so will give A/D clock periods that are less than the minimum A/D clock period which may result in inaccurate A/D conversion values. Refer to the following table for examples, where values marked with an asterisk * show where, depending upon the device, special care must be taken, as the values may be less than the specified minimum A/D Clock Period. A/D Clock Period (tADCK) fSYS SACKS [2:0]=000 (fSYS) SACKS [2:0]=001 (fSYS/2) SACKS [2:0]=010 (fSYS/4) SACKS [2:0]=011 (fSYS/8) SACKS [2:0]=100 (fSYS/16) SACKS [2:0]=101 (fSYS/32) SACKS [2:0]=110 (fSYS/64) SACKS [2:0]=111 (fSYS/128) 1 MHz 1μs 2μs 4μs 8μs 16μs * 32μs * 64μs * 128μs * 2 MHz 500ns 1μs 2μs 4μs 8μs 16μs * 32μs * 64μs * 4 MHz 250ns * 500ns 1μs 2μs 4μs 8μs 16μs * 32μs * 8 MHz 125ns * 250ns * 500ns 1μs 2μs 4μs 8μs 16μs * 12 MHz 83ns * 167ns * 333ns * 667ns 1.33μs 2.67μs 5.33μs 10.67μs * 16 MHz 62.5ns * 125ns * 250ns * 500ns 1μs 2μs 4μs 8μs A/D Clock Period Examples Controlling the power on/off function of the A/D converter circuitry is implemented using the ADCEN bit in the SADC0 register. This bit must be set high to power on the A/D converter. When the ADCEN bit is set high to power on the A/D converter internal circuitry a certain delay, as indicated in the timing diagram, must be allowed before an A/D conversion is initiated. Even if no pins are selected for use as A/D inputs, if the ADCEN bit is high, then some power will still be consumed. In power conscious applications it is therefore recommended that the ADCEN is set low to reduce power consumption when the A/D converter function is not being used. Rev. 1.00 174 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Conversion Rate and Timing Diagram A complete A/D conversion contains two parts, data sampling and data conversion. The data sampling which is defined as tADS takes 4 A/D clock cycles and the data conversion takes 12 A/D clock cycles. Therefore a total of 16 A/D clock cycles for an analog signal A/D conversion which is defined as tADC are necessary. Maximum single A/D conversion rate=A/D clock period / 16 The accompanying diagram shows graphically the various stages involved in an external channel input signal analog to digital conversion process and its associated timing. After an A/D conversion process has been initiated by the application program, the microcontroller internal hardware will begin to carry out the conversion, during which time the program can continue with other functions. The time taken for the A/D conversion is 16 tADCK clock cycles where tADCK is equal to the A/D clock period. tON2ST ADCEN off on off A/D sampling time tADS A/D sampling time tADS Start of A/D conversion Start of A/D conversion on START ADBZ SACS[3:0] (SAINS=000) End of A/D conversion 0011B A/D channel switch End of A/D conversion 0010B tADC A/D conversion time Start of A/D conversion 0000B tADC A/D conversion time 0001B tADC A/D conversion time A/D Conversion Timing Rev. 1.00 175 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Summary of A/D Conversion Steps The following summarises the individual steps that should be executed in order to implement an A/D conversion process. • Step 1 Select the required A/D conversion clock by properly programming the SACKS2~SACKS0 bits in the SADC1 register. • Step 2 Enable the A/D converter by setting the ADCEN bit in the SADC0 register to one. • Step 3 Select which signal is to be connected to the internal A/D converter by correctly configuring the SACS and SAINS bit fields Selecting the external channel input to be converted, go to Step 4. Selecting the internal analog signal to be converted, go to Step 5. • Step 4 If the SAINS field is 0000, 0100 or 11xx, the external channel input can be selected. The desired external channel input is selected by configuring the SACS field. When the A/D input signal comes from the external channel input, the corresponding pin should be configured as an A/D input function by selecting the relevant pin-shared function control bits. Then go to Step 6. • Step 5 If the SAINS field is set to 0x01, 0x10 or 0x11, the relevant internal analog signal will be selected. When the internal analog signal is selected to be converted, the external channel analog input will automatically be disconnected. Then go to Step 6. • Step 6 Select the A/D converter output data format by configuring the ADRFS bit. • Step 7 Select the A/D converter reference voltage source by configuring the SAVRS bit field. Select the PGA input signal and the desired PGA gain if the PGA output voltage, VR, is selected as the A/D converter reference voltage. • Step 8 If A/D conversion interrupt is used, the interrupt control registers must be correctly configured to ensure the A/D interrupt function is active. The master interrupt control bit, EMI, and the A/D conversion interrupt control bit, ADE, must both be set high in advance. • Step 9 The A/D conversion procedure can now be initialized by setting the START bit from low to high and then low again. • Step 10 If A/D conversion is in progress, the ADBZ flag will be set high. After the A/D conversion process is complete, the ADBZ flag will go low and then the output data can be read from SADOH and SADOL registers. Note: When checking for the end of the conversion process, if the method of polling the ADBZ bit in the SADC0 register is used, the interrupt enable step above can be omitted. Rev. 1.00 176 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Programming Considerations During microcontroller operations where the A/D converter is not being used, the A/D internal circuitry can be switched off to reduce power consumption, by setting bit ADCEN low in the SADC0 register. When this happens, the internal A/D converter circuits will not consume power irrespective of what analog voltage is applied to their input lines. If the A/D converter input lines are used as normal I/Os, then care must be taken as if the input voltage is not at a valid logic level, then this may lead to some increase in power consumption. A/D Transfer Function As the devices contain a 12-bit A/D converter, its full-scale converted digitised value is equal to FFFH. Since the full-scale analog input value is equal to the actual A/D converter reference voltage, VREF, this gives a single bit analog input value of reference voltage value divided by 4096. 1 LSB=VREF ÷ 4096 The A/D Converter input voltage value can be calculated using the following equation: A/D input voltage=A/D output digital value × VREF ÷ 4096 The diagram shows the ideal transfer function between the analog input value and the digitised output value for the A/D converter. Except for the digitised zero value, the subsequent digitised values will change at a point 0.5 LSB below where they would change without the offset, and the last full scale digitised value will change at a point 1.5 LSB below the VREF level. Note that here the VREF voltage is the actual A/D converter reference voltage determined by the SAVRS field. 1.5 LSB FFFH FFEH FFDH A/D Conversion Result 03H 0.5 LSB 0�H 01H 0 1 � 3 4093 4094 4095 409� VREF 409� Analog Input Voltage Ideal A/D Transfer Function Rev. 1.00 177 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM A/D Programming Examples The following two programming examples illustrate how to setup and implement an A/D conversion. In the first example, the method of polling the ADBZ bit in the SADC0 register is used to detect when the conversion cycle is complete, whereas in the second example, the A/D interrupt is used to determine when the conversion is complete. Example: using an ADBZ polling method to detect the end of conversion clr ADE; disable ADC interrupt mov a,03H; select fSYS/8 as A/D clock and A/D input mov SADC1,a ; signal comes from external channel mov a,00H ; select AVDD as the A/D reference voltage source mov SADC2,a set ADCEN mov a,02H ; setup PCS0 to configure pin AN0 mov PCS0,a mov a,00H ; select AN0 as the A/D external channel input mov SADC0,a : start_conversion: clr START ; high pulse on start bit to initiate conversion set START ; reset A/D clr START ; start A/D : polling_EOC: sz ADBZ ; poll the SADC0 register ADBZ bit to detect end of A/D conversion jmp polling_EOC ; continue polling : mov a,SADOL ; read low byte conversion result value mov SADOL_buffer,a ; save result to user defined register mov a,SADOH ; read high byte conversion result value mov SADOH_buffer,a ; save result to user defined register : jmp start_conversion ; start next A/D conversion Rev. 1.00 178 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Example: using the interrupt method to detect the end of conversion clr ADE; disable ADC interrupt mov a,03H; select fSYS/8 as A/D clock and A/D input mov SADC1,a ; signal comes from external channel mov a,00H ; select AVDD as the A/D reference voltage source mov SADC2,a set ADCEN mov a,02h ; setup PCS0 to configure pin AN0 mov PCS0,a mov a,00h mov SADC0,a ; select AN0 as the A/D external channel input : Start_conversion: clr START ; high pulse on START bit to initiate conversion set START ; reset A/D clr START ; start A/D clr ADF ; clear ADC interrupt request flag set ADE; enable ADC interrupt set EMI ; enable global interrupt : : ADC_ISR: ; ADC interrupt service routine mov acc_stack,a ; save ACC to user defined memory mov a,STATUS mov status_stack,a ; save STATUS to user defined memory : mov a,SADOL ; read low byte conversion result value mov SADOL_buffer,a ; save result to user defined register mov a,SADOH ; read high byte conversion result value mov SADOH_buffer,a ; save result to user defined register : EXIT_INT_ISR: mov a,status_stack mov STATUS,a ; restore STATUS from user defined memory mov a,acc_stack ; restore ACC from user defined memory reti Rev. 1.00 179 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Serial Interface Module – SIM These devices contain a Serial Interface Module, which includes both the four-line SPI interface or two-line I2C interface types, to allow an easy method of communication with external peripheral hardware. Having relatively simple communication protocols, these serial interface types allow the microcontroller to interface to external SPI or I2C based hardware such as sensors, Flash or EEPROM memory, etc. The SIM interface pins are pin-shared with other I/O pins and therefore the SIM interface functional pins must first be selected using the corresponding pin-shared function selection bits. As both interface types share the same pins and registers, the choice of whether the SPI or I2C type is used is made using the SIM operating mode control bits, named SIM2~SIM0, in the SIMC0 register. These pull-high resistors of the SIM pin-shared I/O pins are selected using pullhigh control registers when the SIM function is enabled and the corresponding pins are used as SIM input pins. SPI Interface The SPI interface is often used to communicate with external peripheral devices such as sensors, Flash or EEPROM memory devices, etc. Originally developed by Motorola, the four line SPI interface is a synchronous serial data interface that has a relatively simple communication protocol simplifying the programming requirements when communicating with external hardware devices. The communication is full duplex and operates as a slave/master type, where the devices can be either master or slave. Although the SPI interface specification can control multiple slave devices from a single master, these devices provided only one SCS pin. If the master needs to control multiple slave devices from a single master, the master can use I/O pin to select the slave devices. SPI Interface Operation The SPI interface is a full duplex synchronous serial data link. It is a four line interface with pin names SDI, SDO, SCK and SCS. Pins SDI and SDO are the Serial Data Input and Serial Data Output lines, SCK is the Serial Clock line and SCS is the Slave Select line. As the SPI interface pins are pin-shared with normal I/O pins and with the I2C function pins, the SPI interface pins must first be selected by configuring the pin-shared function selection bits and setting the correct bits in the SIMC0 and SIMC2 registers. After the desired SPI configuration has been set it can be disabled or enabled using the SIMEN bit in the SIMC0 register. Communication between devices connected to the SPI interface is carried out in a slave/master mode with all data transfer initiations being implemented by the master. The Master also controls the clock signal. As the device only contains a single SCS pin only one slave device can be utilized. The SCS pin is controlled by software, set CSEN bit to 1 to enable SCS pin function, set CSEN bit to 0 the SCS pin will be floating state. The SPI function in this device offers the following features: • Full duplex synchronous data transfer • Both Master and Slave modes • LSB first or MSB first data transmission modes • Transmission complete flag • Rising or falling active clock edge The status of the SPI interface pins is determined by a number of factors such as whether the device is in the master or slave mode and upon the condition of certain control bits such as CSEN and SIMEN. Rev. 1.00 180 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SPI Maste� SPI Slave SCK SCK SDO SDI SDI SDO SCS SCS SPI Master/Slave Connection Data Bus SIMD SDI Pin TX/RX Shift Registe� SDO Pin Clo�k Edge/Pola�ity Cont�ol CKEG CKPOLB WCOL Flag TRF Flag ICF Flag Busy Status SCK Pin Clo�k Sou��e Sele�t fSYS fSUB PTM0 CCRP �at�h f�equen�y/� SCS Pin CSEN SPI Block Diagram SPI Registers There are three internal registers which control the overall operation of the SPI interface. These are the SIMD data register and two registers SIMC0 and SIMC2. Note that the SIMC1 register is only used by the I2C interface. Bit Register Name 7 6 5 4 SIMC0 SIM2 SIM1 SIM0 — SIMC2 D7 D6 CKPOLB CKEG MLS SIMD D7 D6 D5 D4 D3 3 2 1 0 SIMEN SIMICF CSEN WCOL TRF D2 D1 D0 SIMDEB1 SIMDEB0 SPI Registers List • SIMD Register The SIMD register is used to store the data being transmitted and received. The same register is used by both the SPI and I2C functions. Before the device writes data to the SPI bus, the actual data to be transmitted must be placed in the SIMD register. After the data is received from the SPI bus, the device can read it from the SIMD register. Any transmission or reception of data from the SPI bus must be made via the SIMD register. Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR x x x x x x x x "x": unknown Rev. 1.00 181 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM There are also two control registers for the SPI interface, SIMC0 and SIMC2. Note that the SIMC2 register also has the name SIMA which is used by the I2C function. The SIMC1 register is not used by the SPI function, only by the I2C function. Register SIMC0 is used to control the enable/disable function and to set the data transmission clock frequency. Register SIMC2 is used for other control functions such as LSB/MSB selection, write collision flag, etc. • SIMC0 Register Bit 7 6 5 4 Name SIM2 SIM1 SIM0 — R/W R/W R/W R/W — R/W POR 1 1 1 — 0 Bit 7~5 Bit 4 Bit 3~2 Bit 1 Bit 0 Rev. 1.00 3 2 1 0 SIMEN SIMICF R/W R/W R/W 0 0 0 SIMDEB1 SIMDEB0 SIM2~SIM0: SIM Operating Mode Control 000: SPI master mode; SPI clock is fSYS /4 001: SPI master mode; SPI clock is fSYS /16 010: SPI master mode; SPI clock is fSYS /64 011: SPI master mode; SPI clock is fSUB 100: SPI master mode; SPI clock is PTM0 CCRP match frequency/2 101: SPI slave mode 110: I2C slave mode 111: Non SIM function These bits setup the overall operating mode of the SIM function. As well as selecting if the I2C or SPI function, they are used to control the SPI Master/Slave selection and the SPI Master clock frequency. The SPI clock is a function of the system clock but can also be chosen to be sourced from PTM0. If the SPI Slave Mode is selected then the clock will be supplied by an external Master device. Unimplemented, read as "0" SIMDEB1~SIMDEB0: I2C Debounce Time Selection The SIMDEB1~SIMDEB0 bits are only used in the I 2C mode and the detailed definition is described in the I2C section. SIMEN: SIM Enable Control 0: Disable 1: Enable The bit is the overall on/off control for the SIM interface. When the SIMEN bit is cleared to zero to disable the SIM interface, the SDI, SDO, SCK and SCS, or SDA and SCL lines will lose their SPI or I2C function and the SIM operating current will be reduced to a minimum value. When the bit is high the SIM interface is enabled. The SIM configuration option must have first enabled the SIM interface for this bit to be effective. If the SIM is configured to operate as an SPI interface via the SIM2~SIM0 bits, the contents of the SPI control registers will remain at the previous settings when the SIMEN bit changes from low to high and should therefore be first initialised by the application program. If the SIM is configured to operate as an I2C interface via the SIM2~SIM0 bits and the SIMEN bit changes from low to high, the contents of the I2C control bits such as HTX and TXAK will remain at the previous settings and should therefore be first initialised by the application program while the relevant I2C flags such as HCF, HAAS, HBB, SRW and RXAK will be set to their default states. SIMICF: SIM SPI slave mode Incomplete Transfer Flag 0: SIM SPI slave mode incomplete condition not occurred 1: SIM SPI slave mode incomplete condition occurred This bit is only available when the SIM is configured to operate in an SPI slave mode. If the SPI operates in the slave mode with the SIMEN and CSEN bits both being set to 1 but the SCS line is pulled high by the external master device before the SPI data transfer is completely finished, the SIMICF bit will be set to 1 together with the TRF bit. When this condition occurs, the corresponding interrupt will occur if the interrupt function is enabled. However, the TRF bit will not be set to 1 if the SIMICF bit is set to 1 by software application program. 182 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • SIMC2 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name D7 D6 CKPOLB CKEG MLS CSEN WCOL TRF R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 Undefined bits These bits can be read or written by the application program. Bit 5 CKPOLB: SPI clock line base condition selection 0: The SCK line will be high when the clock is inactive. 1: The SCK line will be low when the clock is inactive. The CKPOLB bit determines the base condition of the clock line, if the bit is high, then the SCK line will be low when the clock is inactive. When the CKPOLB bit is low, then the SCK line will be high when the clock is inactive. Bit 4 CKEG: SPI SCK clock active edge type selection CKPOLB=0 0: SCK is high base level and data capture at SCK rising edge 1: SCK is high base level and data capture at SCK falling edge CKPOLB=1 0: SCK is low base level and data capture at SCK falling edge 1: SCK is low base level and data capture at SCK rising edge The CKEG and CKPOLB bits are used to setup the way that the clock signal outputs and inputs data on the SPI bus. These two bits must be configured before data transfer is executed otherwise an erroneous clock edge may be generated. The CKPOLB bit determines the base condition of the clock line, if the bit is high, then the SCK line will be low when the clock is inactive. When the CKPOLB bit is low, then the SCK line will be high when the clock is inactive. The CKEG bit determines active clock edge type which depends upon the condition of CKPOLB bit. Bit 3 MLS: SPI data shift order 0: LSB first 1: MSB first This is the data shift select bit and is used to select how the data is transferred, either MSB or LSB first. Setting the bit high will select MSB first and low for LSB first. Bit 2 CSEN: SPI SCS pin control 0: Disable 1: Enable The CSEN bit is used as an enable/disable for the SCS pin. If this bit is low, then the SCS pin will be disabled and placed into I/O pin or other pin-shared functions. If the bit is high, the SCS pin will be enabled and used as a select pin. Bit 1 WCOL: SPI write collision flag 0: No collision 1: Collision The WCOL flag is used to detect whether a data collision has occurred or not. If this bit is high, it means that data has been attempted to be written to the SIMD register during a data transfer operation. This writing operation will be ignored if data is being transferred. This bit can be cleared by the application program. Bit 0 TRF: SPI Transmit/Receive complete flag 0: SPI data is being transferred 1: SPI data transfer is completed The TRF bit is the Transmit/Receive Complete flag and is set to 1 automatically when an SPI data transfer is completed, but must cleared to 0 by the application program. It can be used to generate an interrupt. 183 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SPI Communication After the SPI interface is enabled by setting the SIMEN bit high, then in the Master Mode, when data is written to the SIMD register, transmission/reception will begin simultaneously. When the data transfer is complete, the TRF flag will be set automatically, but must be cleared using the application program. In the Slave Mode, when the clock signal from the master has been received, any data in the SIMD register will be transmitted and any data on the SDI pin will be shifted into the SIMD register. The master should output a SCS signal to enable the slave devices before a clock signal is provided. The slave data to be transferred should be well prepared at the appropriate moment relative to the SCS signal depending upon the configurations of the CKPOLB bit and CKEG bit. The accompanying timing diagram shows the relationship between the slave data and SCS signal for various configurations of the CKPOLB and CKEG bits. The SPI will continue to function even in the IDLE Mode. SIMEN=1� CSEN=0 (Exte�nal Pull-high) SCS SIMEN� CSEN=1 SCK (CKPOLB=1� CKEG=0) SCK (CKPOLB=0� CKEG=0) SCK (CKPOLB=1� CKEG=1) SCK (CKPOLB=0� CKEG=1) SDO (CKEG=0) D7/D0 D�/D1 D5/D� D4/D3 D3/D4 D�/D5 D1/D� D0/D7 SDO (CKEG=1) D7/D0 D�/D1 D5/D� D4/D3 D3/D4 D�/D5 D1/D� D0/D7 SDI Data Captu�e W�ite to SIMD SPI Master Mode Timing SCS SCK (CKPOLB=1) SCK (CKPOLB=0) SDO D7/D0 D�/D1 D5/D� D4/D3 D3/D4 D�/D5 D1/D� D0/D7 SDI Data Captu�e W�ite to SIMD (SDO does not �hange until fi�st SCK edge) SPI Slave Mode Timing – CKEG=0 Rev. 1.00 184 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SCS SCK (CKPOLB=1) SCK (CKPOLB=0) SDO D7/D0 D�/D1 D5/D� D4/D3 D3/D4 D�/D5 D1/D� D0/D7 SDI Data Captu�e W�ite to SIMD (SDO �hanges as soon as w�iting o��u�s; SDO is floating if SCS=1) Note: Fo� SPI slave �ode� if SIMEN=1 and CSEN=0� SPI is always ena�led and igno�es the SCS level. SPI Slave Mode Timing – CKEG=1 SPI T�ansfe� Maste� Maste� o� Slave ? A W�ite Data into SIMD Clea� WCOL Slave Y SIM[�:0]=000� 001� 010� 011 o� 100 WCOL=1? SIM[�:0]=101 N N Configu�e CKPOLB� CKEG� CSEN and MLS T�ans�ission �o�pleted? (TRF=1?) Y SIMEN=1 Read Data f�o� SIMD A Clea� TRF T�ansfe� finished? N Y END SPI Transfer Control Flow Chart Rev. 1.00 185 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM I2C Interface The I 2C interface is used to communicate with external peripheral devices such as sensors, EEPROM memory etc. Originally developed by Philips, it is a two line low speed serial interface for synchronous serial data transfer. The advantage of only two lines for communication, relatively simple communication protocol and the ability to accommodate multiple devices on the same bus has made it an extremely popular interface type for many applications. VDD SDA SCL Devi�e Slave Devi�e Maste� Devi�e Slave I2C Master/Slave Bus Connection I2C Interface Operation The I2C serial interface is a two line interface, a serial data line, SDA, and serial clock line, SCL. As many devices may be connected together on the same bus, their outputs are both open drain types. For this reason it is necessary that external pull-high resistors are connected to these outputs. Note that no chip select line exists, as each device on the I2C bus is identified by a unique address which will be transmitted and received on the I2C bus. When two devices communicate with each other on the bidirectional I2C bus, one is known as the master device and one as the slave device. Both master and slave can transmit and receive data; however, it is the master device that has overall control of the bus. For these devices, which only operate in slave mode, there are two methods of transferring data on the I2C bus, the slave transmit mode and the slave receive mode. Data Bus Add�ess Mat�h SIMTOEN fSUB HTX De�oun�e Ci��uit�y SIMDEB1 & SIMDEB0 Data in MSB M U X Slave Add�ess Registe� (SIMA) Add�ess Add�ess Mat�h–HAAS Co�pa�ato� SIMTOF Di�e�tion Cont�ol fSYS SCL Pin SDA Pin SIMTOF Ti�e-out Cont�ol I�C Data Registe� (SIMD) Shift Registe� Read/W�ite Slave I�C Inte��upt SRW Data out MSB TXAK 8-�it Data T�ansfe� Co�plete–HCF T�ans�it/ Re�eive Cont�ol Unit Dete�t Sta�t o� Stop HBB I2C Block Diagram Rev. 1.00 186 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM START signal f�o� Maste� Send slave add�ess and R/W �it f�o� Maste� A�knowledge f�o� slave Send data �yte f�o� Maste� A�knowledge f�o� slave STOP signal f�o� Maste� The SIMDEB1 and SIMDEB0 bits determine the debounce time of the I2C interface. This uses the system clock to in effect add a debounce time to the external clock to reduce the possibility of glitches on the clock line causing erroneous operation. The debounce time, if selected, can be chosen to be either 2 or 4 system clocks. To achieve the required I2C data transfer speed, there exists a relationship between the system clock, fSYS, and the I2C debounce time. For either the I2C Standard or Fast mode operation, users must take care of the selected system clock frequency and the configured debounce time to match the criterion shown in the following table. I2C Debounce Time Selection I2C Standard Mode (100kHz) No Debounce fSYS > 2 MHz fSYS > 5 MHz 2 system clock debounce fSYS > 4 MHz fSYS > 10 MHz fSYS > 8 MHz fSYS > 20 MHz 4 system clock debounce I2C Fast Mode (400kHz) I C Minimum fSYS Frequency 2 I2C Registers There are three control registers associated with the I2C bus, SIMC0, SIMC1 and SIMA, and one data register, SIMD. The SIMD register, which is shown in the above SPI section, is used to store the data being transmitted and received on the I2C bus. Before the microcontroller writes data to the I2C bus, the actual data to be transmitted must be placed in the SIMD register. After the data is received from the I2C bus, the microcontroller can read it from the SIMD register. Any transmission or reception of data from the I2C bus must be made via the SIMD register. Note that the SIMA register also has the name SIMC2 which is used by the SPI function. Bit SIMEN and bits SIM2~SIM0 in register SIMC0 are used by the I2C interface. Bit Register Name 7 6 5 4 SIMC0 SIM2 SIM1 SIM0 — SIMC1 HCF HAAS HBB HTX TXAK SIMA IICA6 IICA5 IICA4 IICA3 IICA2 SIMD D7 D6 D5 D4 D3 D2 SIMTOC SIMTOEN 3 2 1 0 SIMEN SIMICF SRW IAMWU RXAK IICA1 IICA0 — D1 D0 SIMDEB1 SIMDEB0 SIMTOF SIMTOS5 SIMTOS4 SIMTOS3 SIMTOS2 SIMTOS1 SIMTOS0 I2C Registers List Rev. 1.00 187 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • SIMD Register The SIMD register is used to store the data being transmitted and received. The same register is used by both the SPI and I2C functions. Before the device writes data to the I2C bus, the actual data to be transmitted must be placed in the SIMD register. After the data is received from the I2C bus, the device can read it from the SIMD register. Any transmission or reception of data from the I2C bus must be made via the SIMD register. Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR x x x x x x x x "x": unknown • SIMA Register The SIMA register is also used by the SPI interface but has the name SIMC2. The SIMA register is the location where the 7-bit slave address of the slave device is stored. Bits 7~1 of the SIMA register define the device slave address. Bit 0 is not implemented. When a master device, which is connected to the I2C bus, sends out an address, which matches the slave address in the SIMA register, the slave device will be selected. Note that the SIMA register is the same register address as SIMC2 which is used by the SPI interface. Bit 7 6 5 4 3 2 1 0 Name IICA6 IICA5 IICA4 IICA3 IICA2 IICA1 IICA0 — R/W R/W R/W R/W R/W R/W R/W R/W — POR x x x x x x x — Bit 7~1 Bit 0 "x": unknown IICA6~IICA0: I2C slave address IICA6~IICA0 is the I2C slave address bit 6 ~ bit 0 Unimplemented, read as "0". SIM Control Registers There are also two control registers for the I2C interface, SIMC0 and SIMC1. The register SIMC0 is used to control the enable/disable function and to set the data transmission clock frequency. The SIMC1 register contains the relevant flags which are used to indicate the I2C communication status. • SIMC0 Register Bit 7 6 5 4 Name SIM2 SIM1 SIM0 — R/W R/W R/W R/W — R/W POR 1 1 1 — 0 Bit 7~5 Rev. 1.00 3 2 1 0 SIMEN SIMICF R/W R/W R/W 0 0 0 SIMDEB1 SIMDEB0 SIM2~SIM0: SIM Operating Mode Control 000: SPI master mode; SPI clock is fSYS /4 001: SPI master mode; SPI clock is fSYS /16 010: SPI master mode; SPI clock is fSYS /64 011: SPI master mode; SPI clock is fSUB 100: SPI master mode; SPI clock is PTM0 CCRP match frequency/2 101: SPI slave mode 110: I2C slave mode 111: Non SIM function These bits setup the overall operating mode of the SIM function. As well as selecting if the I2C or SPI function, they are used to control the SPI Master/Slave selection and the SPI Master clock frequency. The SPI clock is a function of the system clock but can also be chosen to be sourced from PTM0. If the SPI Slave Mode is selected then the clock will be supplied by an external Master device. 188 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 4 Unimplemented, read as "0" Bit 3~2 SIMDEB1~SIMDEB0: I2C Debounce Time Selection 00: No debounce 01: 2 system clock debounce 1x: 4 system clock debounce These bits are used to select the I2C debounce time when the SIM is configured as the I2C interface function by setting the SIM2~SIM0 bits to "110". Bit 1 SIMEN: SIM Enable Control 0: Disable 1: Enable The bit is the overall on/off control for the SIM interface. When the SIMEN bit is cleared to zero to disable the SIM interface, the SDI, SDO, SCK and SCS, or SDA and SCL lines will lose their SPI or I2C function and the SIM operating current will be reduced to a minimum value. When the bit is high the SIM interface is enabled. The SIM configuration option must have first enabled the SIM interface for this bit to be effective.If the SIM is configured to operate as an SPI interface via the SIM2~SIM0 bits, the contents of the SPI control registers will remain at the previous settings when the SIMEN bit changes from low to high and should therefore be first initialised by the application program. If the SIM is configured to operate as an I2C interface via the SIM2~SIM0 bits and the SIMEN bit changes from low to high, the contents of the I2C control bits such as HTX and TXAK will remain at the previous settings and should therefore be first initialised by the application program while the relevant I2C flags such as HCF, HAAS, HBB, SRW and RXAK will be set to their default states. Bit 0 SIMICF: SIM SPI Incomplete Flag The SIMICF bit is only used in the SPI mode and the detailed definition is described in the SPI section. • SIMC1 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name HCF HAAS HBB HTX TXAK SRW IAMWU RXAK R/W R R R R/W R/W R/W R/W R POR 1 0 0 0 0 0 0 1 Bit 7 HCF: I2C Bus data transfer completion flag 0: Data is being transferred 1: Completion of an 8-bit data transfer The HCF flag is the data transfer flag. This flag will be zero when data is being transferred. Upon completion of an 8-bit data transfer the flag will go high and an interrupt will be generated. Bit 6 HAAS: I2C Bus data transfer completion flag 0: Not address match 1: Address match The HAAS flag is the address match flag. This flag is used to determine if the slave device address is the same as the master transmit address. If the addresses match then this bit will be high, if there is no match then the flag will be low. Bit 5 HBB: I2C Bus busy flag 0: I2C Bus is not busy 1: I2C Bus is busy The HBB flag is the I2C busy flag. This flag will be "1" when the I2C bus is busy which will occur when a START signal is detected. The flag will be set to "0" when the bus is free which will occur when a STOP signal is detected. Bit 4 HTX: I2C slave device transmitter/receiver selection 0: Slave device is the receiver 1: Slave device is the transmitter 189 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Rev. 1.00 Bit 3 TXAK: I2C bus transmit acknowledge flag 0: Slave send acknowledge flag 1: Slave does not send acknowledge flag The TXAK bit is the transmit acknowledge flag. After the slave device receipt of 8-bits of data, this bit will be transmitted to the bus on the 9th clock from the slave device. The slave device must always set TXAK bit to "0" before further data is received. Bit 2 SRW: I2C slave read/write flag 0: Slave device should be in receive mode 1: Slave device should be in transmit mode The SRW flag is the I 2C Slave Read/Write flag. This flag determines whether the master device wishes to transmit or receive data from the I2C bus. When the transmitted address and slave address is match, that is when the HAAS flag is set high, the slave device will check the SRW flag to determine whether it should be in transmit mode or receive mode. If the SRW flag is high, the master is requesting to read data from the bus, so the slave device should be in transmit mode. When the SRW flag is zero, the master will write data to the bus, therefore the slave device should be in receive mode to read this data. Bit 1 IAMWU: I2C Address Match Wake-Up control 0: Disable 1: Enable – must be cleared by the application program after wake-up This bit should be set to 1 to enable the I2C address match wake up from the SLEEP or IDLE Mode. If the IAMWU bit has been set before entering either the SLEEP or IDLE mode to enable the I2C address match wake up, then this bit must be cleared by the application program after wake-up to ensure correction device operation. Bit 0 RXAK: I2C bus receive acknowledge flag 0: Slave receives acknowledge flag 1: Slave does not receive acknowledge flag The RXAK flag is the receiver acknowledge flag. When the RXAK flag is "0", it means that a acknowledge signal has been received at the 9th clock, after 8 bits of data have been transmitted. When the slave device in the transmit mode, the slave device checks the RXAK flag to determine if the master receiver wishes to receive the next byte. The slave transmitter will therefore continue sending out data until the RXAK flag is "1". When this occurs, the slave transmitter will release the SDA line to allow the master to send a STOP signal to release the I2C Bus. 190 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM I2C Bus Communication Communication on the I2C bus requires four separate steps, a START signal, a slave device address transmission, a data transmission and finally a STOP signal. When a START signal is placed on the I2C bus, all devices on the bus will receive this signal and be notified of the imminent arrival of data on the bus. The first seven bits of the data will be the slave address with the first bit being the MSB. If the address of the slave device matches that of the transmitted address, the HAAS bit in the SIMC1 register will be set and an I2C interrupt will be generated. After entering the interrupt service routine, the slave device must first check the condition of the HAAS and SIMTOF bits to determine whether the interrupt source originates from an address match, 8-bit data transfer completion or I2C bus time-out occurrence. During a data transfer, note that after the 7-bit slave address has been transmitted, the following bit, which is the 8th bit, is the read/write bit whose value will be placed in the SRW bit. This bit will be checked by the slave device to determine whether to go into transmit or receive mode. Before any transfer of data to or from the I2C bus, the microcontroller must initialise the bus; the following are steps to achieve this: • Step 1 Set the SIM2~SIM0 bits to "110" and SIMEN bit to "1" in the SIMC0 register to enable the I2C bus. • Step 2 Write the slave address of the device to the I2C bus address register SIMA. • Step 3 Set the SIME and SIM Multi-Function interrupt enable bit of the interrupt control register to enable the SIM interrupt and Multi-function interrupt. Sta�t Set SIM[�:0]=110 Set SIMEN W�ite Slave Add�ess to SIMA No Yes I�C Bus Inte��upt=? CLR SIME Poll SIMF to de�ide when to go to I�C Bus ISR SET SIME and MFnE Wait fo� Inte��upt Goto Main P�og�a� Goto Main P�og�a� I2C Bus Initialisation Flow Chart Rev. 1.00 191 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM I2C Bus Start Signal The START signal can only be generated by the master device connected to the I2C bus and not by the slave device. This START signal will be detected by all devices connected to the I2C bus. When detected, this indicates that the I2C bus is busy and therefore the HBB bit will be set. A START condition occurs when a high to low transition on the SDA line takes place when the SCL line remains high. I2C Slave Address The transmission of a START signal by the master will be detected by all devices on the I2C bus. To determine which slave device the master wishes to communicate with, the address of the slave device will be sent out immediately following the START signal. All slave devices, after receiving this 7-bit address data, will compare it with their own 7-bit slave address. If the address sent out by the master matches the internal address of the microcontroller slave device, then an internal I2C bus interrupt signal will be generated. The next bit following the address, which is the 8th bit, defines the read/write status and will be saved to the SRW bit of the SIMC1 register. The slave device will then transmit an acknowledge bit, which is a low level, as the 9th bit. The slave device will also set the status flag HAAS when the addresses match. As an I2C bus interrupt can come from three sources, when the program enters the interrupt subroutine, the HAAS and SIMTOF bits should be examined to see whether the interrupt source has come from a matching slave address, the completion of a data byte transfer or the I2C bus time-out occurrence. When a slave address is matched, the devices must be placed in either the transmit mode and then write data to the SIMD register, or in the receive mode where it must implement a dummy read from the SIMD register to release the SCL line. I2C Bus Read/Write Signal The SRW bit in the SIMC1 register defines whether the slave device wishes to read data from the I2C bus or write data to the I2C bus. The slave device should examine this bit to determine if it is to be a transmitter or a receiver. If the SRW flag is "1" then this indicates that the master device wishes to read data from the I2C bus, therefore the slave device must be setup to send data to the I2C bus as a transmitter. If the SRW flag is "0" then this indicates that the master wishes to send data to the I2C bus, therefore the slave device must be setup to read data from the I2C bus as a receiver. I2C Bus Slave Address Acknowledge Signal After the master has transmitted a calling address, any slave device on the I 2C bus, whose own internal address matches the calling address, must generate an acknowledge signal. The acknowledge signal will inform the master that a slave device has accepted its calling address. If no acknowledge signal is received by the master then a STOP signal must be transmitted by the master to end the communication. When the HAAS flag is high, the addresses have matched and the slave device must check the SRW flag to determine if it is to be a transmitter or a receiver. If the SRW flag is high, the slave device should be setup to be a transmitter so the HTX bit in the SIMC1 register should be set to "1". If the SRW flag is low, then the microcontroller slave device should be setup as a receiver and the HTX bit in the SIMC1 register should be set to "0". Rev. 1.00 192 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM I2C Bus Data and Acknowledge Signal The transmitted data is 8-bits wide and is transmitted after the slave device has acknowledged receipt of its slave address. The order of serial bit transmission is the MSB first and the LSB last. After receipt of 8-bits of data, the receiver must transmit an acknowledge signal, level "0", before it can receive the next data byte. If the slave transmitter does not receive an acknowledge bit signal from the master receiver, then the slave transmitter will release the SDA line to allow the master to send a STOP signal to release the I2C Bus. The corresponding data will be stored in the SIMD register. If setup as a transmitter, the slave device must first write the data to be transmitted into the SIMD register. If setup as a receiver, the slave device must read the transmitted data from the SIMD register. When the slave receiver receives the data byte, it must generate an acknowledge bit, known as TXAK, on the 9th clock. The slave device, which is setup as a transmitter will check the RXAK bit in the SIMC1 register to determine if it is to send another data byte, if not then it will release the SDA line and await the receipt of a STOP signal from the master. SCL Slave Add�ess Sta�t 1 0 1 SDA 1 0 1 SRW ACK 1 0 0 Data SCL 1 0 0 1 0 ACK 1 0 Stop 0 SDA S=Sta�t (1 �it) SA=Slave Add�ess (7 �its) SR=SRW �it (1 �it) M=Slave devi�e send a�knowledge �it (1 �it) D=Data (8 �its) A=ACK (RXAK �it fo� t�ans�itte�� TXAK �it fo� �e�eive�� 1 �it) P=Stop (1 �it) S SA SR M D A D A …… S SA SR M D A D A …… P Note: *When a slave address is matched, the device must be placed in either the transmit mode and then write data to the SIMD register, or in the receive mode where it must implement a dummy read from the SIMD register to release the SCL line. I2C Communication Timing Diagram Rev. 1.00 193 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Sta�t No No No HTX=1? Yes HAAS=1? Yes SIMTOF=1? Yes Yes SET SIMTOEN CLR SIMTOF SRW=1? No RETI Read f�o� SIMD to �elease SCL Line RETI Yes SET HTX CLR HTX CLR TXAK W�ite data to SIMD to �elease SCL Line Du��y �ead f�o� SIMD to �elease SCL Line RETI RETI RXAK=1? No CLR HTX CLR TXAK W�ite data to SIMD to �elease SCL Line Du��y �ead f�o� SIMD to �elease SCL Line RETI RETI I2C Bus ISR Flow Chart I2C Time-out Control In order to reduce the I2C lockup problem due to reception of erroneous clock sources, a time-out function is provided. If the clock source connected to the I2C bus is not received for a while, then the I2C circuitry and registers will be reset after a certain time-out period. The time-out counter starts to count on an I2C bus "START" & "address match" condition, and is cleared by an SCL falling edge. Before the next SCL falling edge arrives, if the time elapsed is greater than the time-out period specified by the SIMTOC register, then a time-out condition will occur. The time-out function will stop when an I2C "STOP" condition occurs. Rev. 1.00 194 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SCL Sta�t Slave Add�ess 1 SDA 0 1 1 0 1 SRW ACK 1 0 0 I�C ti�e-out �ounte� sta�t Stop SCL 1 0 0 1 0 1 0 0 SDA I�C ti�e-out �ounte� �eset on SCL negative t�ansition I2C Time-out When an I2C time-out counter overflow occurs, the counter will stop and the SIMTOEN bit will be cleared to zero and the SIMTOF bit will be set high to indicate that a time-out condition has occurred. The time-out condition will also generate an interrupt which uses the I2C interrupt vector. When an I2C time-out occurs, the I2C internal circuitry will be reset and the registers will be reset into the following condition: Register After I2C Time-out SIMD, SIMA, SIMC0 No change SIMC1 Reset to POR condition I2C Register after Time-out The SIMTOF flag can be cleared by the application program. There are 64 time-out period selections which can be selected using the SIMTOS bits in the SIMTOC register. The time-out duration is calculated by the formula: ((1~64) × (32/fSUB)). This gives a time-out period which ranges from about 1ms to 64ms. • SIMTOC Register Bit Name Rev. 1.00 7 6 5 4 3 2 1 0 SIMTOEN SIMTOF SIMTOS5 SIMTOS4 SIMTOS3 SIMTOS2 SIMTOS1 SIMTOS0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 SIMTOEN: SIM I C Time-out control 0: Disable 1: Enable Bit 6 SIMTOF: SIM I2C Time-out flag 0: No time-out occurred 1: Time-out occurred Bit 5~0 SIMTOS5~SIMTOS0: SIM I2C Time-out period selection I2C Time-out clock source is fSUB/32 I2C Time-out period is equal to (SIMTOS[5:0]+1) × (32/fSUB) 2 195 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Serial Interface – SPIA These devices contain an independent SPI function. It is important not to confuse this independent SPI function with the additional one contained within the combined SIM function, which is described in another section of this datasheet. This independent SPI function will carry the name SPIA to distinguish it from the other one in the SIM. This SPIA interface is often used to communicate with external peripheral devices such as sensors, Flash or EEPROM memory devices, etc. Originally developed by Motorola, the four line SPI interface is a synchronous serial data interface that has a relatively simple communication protocol simplifying the programming requirements when communicating with external hardware devices. The communication is full duplex and operates as a slave/master type, where the device can be either master or slave. Although the SPIA interface specification can control multiple slave devices from a single master, this device is provided only one SCSA pin. If the master needs to control multiple slave devices from a single master, the master can use I/O pins to select the slave devices. SPIA Interface Operation The SPIA interface is a full duplex synchronous serial data link. It is a four line interface with pin names SDIA, SDOA, SCKA and SCSA. Pins SDIA and SDOA are the Serial Data Input and Serial Data Output lines, SCKA is the Serial Clock line and SCSA is the Slave Select line. As the SPIA interface pins are pin-shared with other functions, the SPIA interface pins must first be selected by configuring the corresponding selection bits in the pin-shared function selection registers. The SPIA interface function is disabled or enabled using the SPIAEN bit in the SPIAC0 register. Communication between devices connected to the SPIA interface is carried out in a slave/master mode with all data transfer initiations being implemented by the master. The master also controls the clock/signal. As the device only contains a single SCSA pin only one slave device can be utilised. The SCSA pin is controlled by the application program, set the SACSEN bit to "1" to enable the SCSA pin function and clear the SACSEN bit to "0" to place the SCSA pin into an I/O function. SPIA Maste� SPIA Slave SCKA SCKA SDOA SDIA SDIA SDOA SCSA SCSA SPIA Master/Slave Connection The SPIA Serial Interface function includes the following features: • Full-duplex synchronous data transfer • Both Master and Slave mode • LSB first or MSB first data transmission modes • Transmission complete flag • Rising or falling active clock edge The status of the SPIA interface pins is determined by a number of factors such as whether the device is in the master or slave mode and upon the condition of certain control bits such as SACSEN and SPIAEN. Rev. 1.00 196 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Data Bus SPIAD SDIA Pin TX/RX Shift Registe� Clo�k Edge/Pola�ity Cont�ol SACKEG SACKPOLB Busy Status SCKA Pin SAWCOL SATRF SPIAICF Clo�k Sou��e Sele�t fSYS fSUB PTM0 CCRP �at�h f�equen�y/� SCSA Pin SDOA Pin SACSEN SPIA Block Diagram SPIA Registers There are three internal registers which control the overall operation of the SPIA interface. These are the SPIAD data register and two registers SPIAC0 and SPIAC1. Bit Register Name 7 6 5 4 3 2 1 0 SPIAC0 SASPI2 SASPI1 SASPI0 — — — SPIAEN SPIAICF SPIAC1 — — SPIAD D7 D6 SACKPOLB SACKEG D5 SAMLS D4 D3 SACSEN SAWCOL D2 D1 SATRF D0 SPIA Registers List SPIAD Register The SPIAD register is used to store the data being transmitted and received. Before the device writes data to the SPIA bus, the actual data to be transmitted must be placed in the SPIAD register. After the data is received from the SPIA bus, the device can read it from the SPIAD register. Any transmission or reception of data from the SPIA bus must be made via the SPIAD register. Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR x x x x x x x x "x": unknown There are also two control registers for the SPIA interface, SPIAC0 and SPIAC1. Register SPIAC0 is used to control the enable/disable function and to set the data transmission clock frequency. Register SPIAC1 is used for other control functions such as LSB/MSB selection, write collision flag, etc. Rev. 1.00 197 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SPIAC0 Register Bit 7 6 5 4 3 2 1 0 Name SASPI2 SASPI1 SASPI0 — — — SPIAEN SPIAICF R/W R/W R/W R/W — — — R/W R/W POR 1 1 1 — — — 0 0 Bit 7~5 Rev. 1.00 SASPI2~SASPI0: SPIA Master/Slave clock select 000: SPIA master mode with clock fSYS/4 001: SPIA master mode with clock fSYS/16 010: SPIA master mode with clock fSYS/64 011: SPIA master mode with clock fSUB 100: SPIA master mode with clock PTM0 CCRP match frequency/2 101: SPIA slave mode 11x: SPIA disable Bit 4~2 Unimplemented, read as "0" Bit 1 SPIAEN: SPIA Enable Control 0: Disable 1: Enable The bit is the overall on/off control for the SPIA interface. When the SPIAEN bit is cleared to zero to disable the SPIA interface, the SDIA, SDOA, SCKA and SCSA lines will lose the SPI function and the SPIA operating current will be reduced to a minimum value. When the bit is high the SPIA interface is enabled. Bit 0 SPIAICF: SPIA Incomplete Flag 0: SPIA incomplete condition not occurred 1: SPIA incomplete condition occurred This bit is only available when the SPIA is configured to operate in an SPIA slave mode. If the SPIA operates in the slave mode with the SPIAEN and SACSEN bits both being set to 1 but the SCSA line is pulled high by the external master device before the SPIA data transfer is completely finished, the SPIAICF bit will be set to 1 together with the SATRF bit. When this condition occurs, the corresponding interrupt will occur if the interrupt function is enabled. However, the SATRF bit will not be set to 1 if the SPIAICF bit is set to 1 by software application program. 198 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SPIAC1 Register Rev. 1.00 Bit 7 6 Name — — 5 4 SACKPOLB SACKEG 3 SAMLS 2 1 0 SACSEN SAWCOL SATRF R/W — — R/W R/W R/W R/W R/W R/W POR — — 0 0 0 0 0 0 Bit 7~6 Unimplemented, read as "0" Bit 5 SACKPOLB: SPIA clock line base condition selection 0: The SCKA line will be high when the clock is inactive. 1: The SCKA line will be low when the clock is inactive. The SACKPOLB bit determines the base condition of the clock line, if the bit is high, then the SCKA line will be low when the clock is inactive. When the SACKPOLB bit is low, then the SCKA line will be high when the clock is inactive. Bit 4 SACKEG: SPIA SCKA clock active edge type selection SACKPOLB=0 0: SCKA is high base level and data capture at SCKA rising edge 1: SCKA is high base level and data capture at SCKA falling edge SACKPOLB=1 0: SCKA is low base level and data capture at SCKA falling edge 1: SCKA is low base level and data capture at SCKA rising edge The SACKEG and SACKPOLB bits are used to setup the way that the clock signal outputs and inputs data on the SPIA bus. These two bits must be configured before data transfer is executed otherwise an erroneous clock edge may be generated. The SACKPOLB bit determines the base condition of the clock line, if the bit is high, then the SCKA line will be low when the clock is inactive. When the SACKPOLB bit is low, then the SCKA line will be high when the clock is inactive. The SACKEG bit determines active clock edge type which depends upon the condition of SACKPOLB bit. Bit 3 SAMLS: SPIA data shift order 0: LSB first 1: MSB first This is the data shift select bit and is used to select how the data is transferred, either MSB or LSB first. Setting the bit high will select MSB first and low for LSB first. Bit 2 SACSEN: SPIA SCSA pin control 0: Disable 1: Enable The SACSEN bit is used as an enable/disable for the SCSA pin. If this bit is low, then the SCSA pin function will be disabled and can be placed into I/O pin or other pinshared functions. If the bit is high, the SCSA pin will be enabled and used as a select pin. Bit 1 SAWCOL: SPIA write collision flag 0: No collision 1: Collision The SAWCOL flag is used to detect whether a data collision has occurred or not. If this bit is high, it means that data has been attempted to be written to the SPIAD register during a data transfer operation. This writing operation will be ignored if data is being transferred. This bit can be cleared by the application program. Bit 0 SATRF: SPIA Transmit/Receive complete flag 0: SPIA data is being transferred 1: SPIA data transfer is completed The SATRF bit is the Transmit/Receive Complete flag and is set to 1 automatically when an SPIA data transfer is completed, but must cleared to 0 by the application program. It can be used to generate an interrupt. 199 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SPIA Communication After the SPIA interface is enabled by setting the SPIAEN bit high, then in the Master Mode, when data is written to the SPIAD register, transmission/reception will begin simultaneously. When the data transfer is complete, the SATRF flag will be set automatically, but must be cleared using the application program. In the Slave Mode, when the clock signal from the master has been received, any data in the SPIAD register will be transmitted and any data on the SDIA pin will be shifted into the SPIAD registers. The master should output a SCSA signal to enable the slave device before a clock signal is provided. The slave data to be transferred should be well prepared at the appropriate moment relative to the SCSA signal depending upon the configurations of the SACKPOLB bit and SACKEG bit. The accompanying timing diagram shows the relationship between the slave data and SCSA signal for various configurations of the SACKPOLB and SACKEG bits. The SPIA will continue to function if the SPIA clock source is active. SPIAEN=1� SACSEN=0 (Exte�nal Pull-high) SCSA SPIAEN� SACSEN=1 SCKA (SACKPOLB=1� SACKEG=0) SCKA (SACKPOLB=0� SACKEG=0) SCKA (SACKPOLB=1� SACKEG=1) SCKA (SACKPOLB=0� SACKEG=1) SDOA (SACKEG=0) D7/D0 D�/D1 D5/D� D4/D3 D3/D4 D�/D5 D1/D� D0/D7 SDOA (SACKEG=1) D7/D0 D�/D1 D5/D� D4/D3 D3/D4 D�/D5 D1/D� D0/D7 SDIA Data Captu�e W�ite to SPIAD SPIA Master Mode Timing SCSA SCKA (SACKPOLB=1) SCKA (SACKPOLB=0) SDOA D7/D0 D�/D1 D5/D� D4/D3 D3/D4 D�/D5 D1/D� D0/D7 SDIA Data Captu�e W�ite to SPIAD (SDOA does not �hange until fi�st SCKA edge) SPIA Slave Mode Timing – SACKEG=0 Rev. 1.00 200 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SCSA SCKA (SACKPOLB=1) SCKA (SACKPOLB=0) SDOA D7/D0 D�/D1 D5/D� D4/D3 D3/D4 D�/D5 D1/D� D0/D7 SDIA Data Captu�e W�ite to SPIAD (SDOA �hanges as soon as w�iting o��u�s; SDOA is floating if SCSA=1) Note: Fo� SPIA slave �ode� if SPIAEN=1 and SACSEN=0� SPIA is always ena�led and igno�es the SCSA level. SPIA Slave Mode Timing – SACKEG=1 SPIA T�ansfe� Maste� Maste� o� Slave ? A W�ite Data into SPIAD Clea� SAWCOL Slave Y SASPI[�:0]=000� 001� 010� 011 o� 100 SAWCOL=1? SASPI[�:0]=101 N N Configu�e SACKPOLB� SACKEG� SACSEN and SAMLS T�ans�ission �o�pleted? (SATRF=1?) Y SPIAEN=1 Read Data f�o� SPIAD A Clea� SATRF T�ansfe� finished? N Y END SPIA Transfer Control Flow Chart Rev. 1.00 201 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SPIA Bus Enable/Disable To enable the SPIA bus, set SACSEN=1 and SCSA=0, then wait for data to be written into the SPIAD (TXRX buffer) register. For the Master Mode, after data has been written to the SPIAD (TXRX buffer) register, then transmission or reception will start automatically. When all the data has been transferred the SATRF bit should be set. For the Slave Mode, when clock pulses are received on SCKA, data in the TXRX buffer will be shifted out or data on SDIA will be shifted in. When the SPIA bus is disabled, the SCKA, SDIA, SDOA and SCSA pins can become I/O pins or other pin-shared functions using the corresponding pin-shared function selection bits. SPIA Operation All communication is carried out using the 4-line interface for either Master or Slave Mode. The SACSEN bit in the SPIAC1 register controls the overall function of the SPIA interface. Setting this bit high will enable the SPIA interface by allowing the SCSA line to be active, which can then be used to control the SPIA interface. If the SACSEN bit is low, the SPIA interface will be disabled and the SCSA line will be an I/O pin or other pin-shared functions and can therefore not be used for control of the SPIA interface. If the SACSEN bit and the SPIAEN bit in the SPIAC0 register are set high, this will place the SDIA line in a floating condition and the SDOA line high. If in Master Mode the SCKA line will be either high or low depending upon the clock polarity selection bit SACKPOLB in the SPIAC1 register. If in Slave Mode the SCKA line will be in a floating condition. If SPIAEN is low, then the bus will be disabled and SCSA, SDIA, SDOA and SCKA pins will all become I/O pins or other pin-shared functions using the corresponding pin-shared function selection bits. In the Master Mode the Master will always generate the clock signal. The clock and data transmission will be initiated after data has been written into the SPIAD register. In the Slave Mode, the clock signal will be received from an external master device for both data transmission and reception. The following sequences show the order to be followed for data transfer in both Master and Slave Mode. Master Mode: • Step 1 Select the clock source and Master mode using the SASPI2~SASPI0 bits in the SPIAC0 control register. • Step 2 Setup the SACSEN bit and setup the SAMLS bit to choose if the data is MSB or LSB shifted first, this must be same as the Slave device. • Step 3 Setup the SPIAEN bit in the SPIAC0 control register to enable the SPIA interface. • Step 4 For write operations: write the data to the SPIAD register, which will actually place the data into the TXRX buffer. Then use the SCKA and SCSA lines to output the data. After this go to step 5. For read operations: the data transferred in on the SDIA line will be stored in the TXRX buffer until all the data has been received at which point it will be latched into the SPIAD register. • Step 5 Check the SAWCOL bit if set high then a collision error has occurred so return to step 4. If equal to zero then go to the following step. • Step 6 Check the SATRF bit or wait for a SPIA serial bus interrupt. Rev. 1.00 202 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • Step 7 Read data from the SPIAD register. • Step 8 Clear SATRF. • Step 9 Go to step 4. Slave Mode: • Step 1 Select the SPI Slave mode using the SASPI2~SASPI0 bits in the SPIAC0 control register • Step 2 Setup the SACSEN bit and setup the SAMLS bit to choose if the data is MSB or LSB shifted first, this setting must be the same with the Master device. • Step 3 Setup the SPIAEN bit in the SPIAC0 control register to enable the SPIA interface. • Step 4 For write operations: write the data to the SPIAD register, which will actually place the data into the TXRX buffer. Then wait for the master clock SCKA and SCSA signal. After this, go to step 5. For read operations: the data transferred in on the SDIA line will be stored in the TXRX buffer until all the data has been received at which point it will be latched into the SPIAD register. • Step 5 Check the SAWCOL bit if set high then a collision error has occurred so return to step 4. If equal to zero then go to the following step. • Step 6 Check the SATRF bit or wait for a SPIA serial bus interrupt. • Step 7 Read data from the SPIAD register. • Step 8 Clear SATRF. • Step 9 Go to step 4. Error Detection The SAWCOL bit in the SPIAC1 register is provided to indicate errors during data transfer. The bit is set by the SPIA serial Interface but must be cleared by the application program. This bit indicates a data collision has occurred which happens if a write to the SPIAD register takes place during a data transfer operation and will prevent the write operation from continuing. Rev. 1.00 203 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM UART Interface These devices contain up to three integrated full-duplex asynchronous serial communications UART interfaces that enable communication with external devices that contain a serial interface. The UART function has many features and can transmit and receive data serially by transferring a frame of data with eight or nine data bits per transmission as well as being able to detect errors when the data is overwritten or incorrectly framed. The UART function possesses its own internal interrupt which can be used to indicate when a reception occurs or when a transmission terminates. Decive UART Interface HT67F2350/HT67F2360 2 HT67F2370/HT67F2390 3 Each integrated UART function contains the following features: • Full-duplex, asynchronous communication • 8 or 9 bits character length • Even, odd or no parity options • One or two stop bits • Baud rate generator with 8-bit prescaler • Parity, framing, noise and overrun error detection • Support for interrupt on address detect (last character bit=1) • Separately enabled transmitter and receiver • 2-byte Deep FIFO Receive Data Buffer • RX pin wake-up function • Transmit and receive interrupts • Interrupts can be initialized by the following conditions: ♦♦ Transmitter Empty ♦♦ Transmitter Idle ♦♦ Receiver Full ♦♦ Receiver Overrun ♦♦ Address Mode Detect T�ans�itte� Shift Registe� (TSRn) MSB ………………………… LSB TXn Pin RXn Pin TX Registe� (TXRn) Re�eive� Shift Registe� (RSRn) MSB ………………………… LSB RX Registe� (RXRn) Buffe� Baud Rate Gene�ato� n fH Data to �e t�ans�itted Data �e�eived MCU Data Bus UART Data Transfer Block Diagram Rev. 1.00 204 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM UART External Pin To communicate with an external serial interface, the internal UARTn has two external pins known as TXn and RXn. The TXn and RXn pins are the UARTn transmitter and receiver pins respectively. The TXn and RXn pin function should first be selected by the corresponding pin-shared function selection register before the UARTn function is used. Along with the UARTENn bit, the TXENn and RXENn bits, if set, will automatically setup the TXn and RXn pins to their respective TXn output and RXn input conditions and disable any pull-high resistor option which may exist on the TXn and RXn pins. When the TXn or RXn pin function is disabled by clearing the UARTENn, TXENn or RXENn bit, the TXn or RXn pin will be set to a floating state. At this time whether the internal pullhigh resistor is connected to the TXn or RXn pin or not is determined by the corresponding I/O pullhigh function control bit. UART Data Transfer Scheme The above diagram shows the overall data transfer structure arrangement for the UARTn interface. The actual data to be transmitted from the MCU is first transferred to the TXRn register by the application program. The data will then be transferred to the Transmit Shift Register from where it will be shifted out, LSB first, onto the TXn pin at a rate controlled by the Baud Rate Generator n. Only the TXRn register is mapped onto the MCU Data Memory, the Transmit Shift Register is not mapped and is therefore inaccessible to the application program. Data to be received by the UARTn is accepted on the external RXn pin, from where it is shifted in, LSB first, to the Receiver Shift Register at a rate controlled by the Baud Rate Generator. When the shift register is full, the data will then be transferred from the shift register to the internal RXRn register, where it is buffered and can be manipulated by the application program. Only the TXRn register is mapped onto the MCU Data Memory, the Receiver Shift Register is not mapped and is therefore inaccessible to the application program. It should be noted that the actual register for data transmission and reception, although referred to in the text, and in application programs, as separate TXRn and RXRn registers, only exists as a single shared register in the Data Memory. This shared register known as the TXR_RXRn register is used for both data transmission and data reception. UART Status and Control Registers There are five control registers associated with the UARTn function. The UnSR, UnCR1 and UnCR2 registers control the overall function of the UARTn, while the BRGn register controls the Baud rate. The actual data to be transmitted and received on the serial interface is managed through the TXR_ RXRn data registers. TXR_RXRn Register The TXR_RXRn register is the data register which is used to store the data to be transmitted on the TXn pin or being received from the RXn pin. Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR x x x x x x x x "x": unknown Bit 7~0 Rev. 1.00 D7~D0: UARTn Transmit/Receive Data bits 205 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM UnSR Register The UnSR register is the status register for the UARTn, which can be read by the program to determine the present status of the UARTn. All flags within the UnSR register are read only and further explanations are given below. Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name PERRn NFn FERRn OERRn RIDLEn RXIFn TIDLEn TXIFn R/W R R R R R R R R POR 0 0 0 0 1 0 1 1 Bit 7 PERRn: Parity error flag 0: No parity error is detected 1: Parity error is detected The PERRn flag is the parity error flag. When this read only flag is "0", it indicates a parity error has not been detected. When the flag is "1", it indicates that the parity of the received word is incorrect. This error flag is applicable only if Parity mode (odd or even) is selected. The flag can also be cleared by a software sequence which involves a read to the status register UnSR followed by an access to the TXR_RXRn data register. Bit 6 NFn: Noise flag 0: No noise is detected 1: Noise is detected The NFn flag is the noise flag. When this read only flag is "0", it indicates no noise condition. When the flag is "1", it indicates that the UARTn has detected noise on the receiver input. The NFn flag is set during the same cycle as the RXIFn flag but will not be set in the case of as overrun. The NFn flag can be cleared by a software sequence which will involve a read to the status register UnSR followed by an access to the TXR_RXRn data register. Bit 5 FERRn: Framing error flag 0: No framing error is detected 1: Framing error is detected The FERRn flag is the framing error flag. When this read only flag is "0", it indicates that there is no framing error. When the flag is "1", it indicates that a framing error has been detected for the current character. The flag can also be cleared by a software sequence which will involve a read to the status register UnSR followed by an access to the TXR_RXRn data register. Bit 4 OERRn: Overrun error flag 0: No overrun error is detected 1: Overrun error is detected The OERRn flag is the overrun error flag which indicates when the receiver buffer has overflowed. When this read only flag is "0", it indicates that there is no overrun error. When the flag is "1", it indicates that an overrun error occurs which will inhibit further transfers to the TXR_RXRn receive data register. The flag is cleared by a software sequence, which is a read to the status register UnSR followed by an access to the TXR_RXRn data register. Bit 3 RIDLEn: Receiver status 0: data reception is in progress (data being received) 1: no data reception is in progress (receiver is idle) The RIDLEn flag is the receiver status flag. When this read only flag is "0", it indicates that the receiver is between the initial detection of the start bit and the completion of the stop bit. When the flag is "1", it indicates that the receiver is idle. Between the completion of the stop bit and the detection of the next start bit, the RIDLEn bit is "1" indicating that the UARTn receiver is idle and the RXn pin stays in logic high condition. 206 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 2 RXIFn: Receive TXR_RXRn data register status 0: TXR_RXRn data register is empty 1: TXR_RXRn data register has available data The RXIFn flag is the receive data register status flag. When this read only flag is "0", it indicates that the TXR_RXRn read data register is empty. When the flag is "1", it indicates that the TXR_RXRn read data register contains new data. When the contents of the shift register are transferred to the TXR_RXRn register, an interrupt is generated if RIEn=1 in the UnCR2 register. If one or more errors are detected in the received word, the appropriate receive-related flags NFn, FERRn, and/or PERRn are set within the same clock cycle. The RXIFn flag will eventually be cleared when the UnSR register is read with RXIFn set, followed by a read from the TXR_RXRn register, and if the TXR_RXRn register has no more new data available. Bit 1 TIDLEn: Transmission status 0: data transmission is in progress (data being transmitted) 1: no data transmission is in progress (transmitter is idle) The TIDLEn flag is known as the transmission complete flag. When this read only flag is "0", it indicates that a transmission is in progress. This flag will be set to "1" when the TXIFn flag is "1" and when there is no transmit data or break character being transmitted. When TIDLEn is equal to 1, the TXn pin becomes idle with the pin state in logic high condition. The TIDLEn flag is cleared by reading the UnSR register with TIDLEn set and then writing to the TXR_RXRn register. The flag is not generated when a data character or a break is queued and ready to be sent. Bit 0 TXIFn: Transmit TXR data register status 0: character is not transferred to the transmit shift register 1: character has transferred to the transmit shift register (TXR_RXRn data register is empty) The TXIFn flag is the transmit data register empty flag. When this read only flag is "0", it indicates that the character is not transferred to the transmitter shift register. When the flag is "1", it indicates that the transmitter shift register has received a character from the TXR_RXRn data register. The TXIFn flag is cleared by reading the UARTn status register (UnSR) with TXIFn set and then writing to the TXR_RXRn data register. Note that when the TXENn bit is set, the TXIFn flag bit will also be set since the transmit data register is not yet full. UnCR1 Register The UnCR1 register together with the UnCR2 register are the UARTn control registers that are used to set the various options for the UARTn function such as overall on/off control, parity control, data transfer bit length, etc. Further explanation on each of the bits is given below. Bit 7 6 5 4 3 2 1 0 Name UARTENn BNOn PRENn PRTn STOPSn TXBRKn RX8n TX8n R/W R/W R/W R/W R/W R/W R/W R W POR 0 0 0 0 0 0 x 0 "x": unknown Bit 7 Rev. 1.00 UARTENn: UARTn function enable control 0: Disable UARTn; TXn and RXn pins are in a high impedance state. 1: Enable UARTn; TXn and RXn pins function as UARTn pins The UARTENn bit is the UARTn enable bit. When this bit is equal to "0", the UARTn will be disabled and the RXn pin as well as the TXn pin will be set in a high impedance state. When the bit is equal to "1", the UARTn will be enabled and the TXn and RXn pins will function as defined by the TXENn and RXENn enable control bits. When the UARTn is disabled, it will empty the buffer so any character remaining in the buffer will be discarded. In addition, the value of the baud rate counter will be reset. If the UARTn is disabled, all error and status flags will be reset. Also the TXENn, RXENn, TXBRKn, RXIFn, OERRn, FERRn, PERRn and NFn bits will be 207 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM cleared, while the TIDLEn, TXIFn and RIDLEn bits will be set. Other control bits in UnCR1, UnCR2 and BRGn registers will remain unaffected. If the UARTn is active and the UARTENn bit is cleared, all pending transmissions and receptions will be terminated and the module will be reset as defined above. When the UARTn is reenabled, it will restart in the same configuration. Rev. 1.00 Bit 6 BNOn: Number of data transfer bits selection 0: 8-bit data transfer 1: 9-bit data transfer This bit is used to select the data length format, which can have a choice of either 8-bit or 9-bit format. When this bit is equal to "1", a 9-bit data length format will be selected. If the bit is equal to "0", then an 8-bit data length format will be selected. If 9-bit data length format is selected, then bits RX8n and TX8n will be used to store the 9th bit of the received and transmitted data respectively. Bit 5 PRENn: Parity function enable control 0: Parity function is disabled 1: Parity function is enabled This bit is the parity function enable bit. When this bit is equal to 1, the parity function will be enabled. If the bit is equal to 0, then the parity function will be disabled. Bit 4 PRTn: Parity type selection bit 0: Even parity for parity generator 1: Odd parity for parity generator This bit is the parity type selection bit. When this bit is equal to 1, odd parity type will be selected. If the bit is equal to 0, then even parity type will be selected. Bit 3 STOPSn: Number of stop bits selection 0: One stop bit format is used 1: Two stop bits format is used This bit determines if one or two stop bits are to be used. When this bit is equal to "1", two stop bits format are used. If the bit is equal to "0", then only one stop bit format is used. Bit 2 TXBRKn: Transmit break character 0: No break character is transmitted 1: Break characters transmit The TXBRKn bit is the Transmit Break Character bit. When this bit is equal to "0", there are no break characters and the TXn pin operates normally. When the bit is equal to "1", there are transmit break characters and the transmitter will send logic zeros. When this bit is equal to "1", after the buffered data has been transmitted, the transmitter output is held low for a minimum of a 13-bit length and until the TXBRKn bit is reset. Bit 1 RX8n: Receive data bit 8 for 9-bit data transfer format (read only) This bit is only used if 9-bit data transfers are used, in which case this bit location will store the 9th bit of the received data known as RX8n. The BNOn bit is used to determine whether data transfers are in 8-bit or 9-bit format. Bit 0 TX8n: Transmit data bit 8 for 9-bit data transfer format (write only) This bit is only used if 9-bit data transfers are used, in which case this bit location will store the 9th bit of the transmitted data known as TX8n. The BNOn bit is used to determine whether data transfers are in 8-bit or 9-bit format. 208 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM UnCR2 Register The UnCR2 register is the second of the UARTn control registers and serves several purposes. One of its main functions is to control the basic enable/disable operation if the UARTn Transmitter and Receiver as well as enabling the various UARTn interrupt sources. The register also serves to control the baud rate speed, receiver wake-up function enable and the address detect function enable. Further explanation on each of the bits is given below. Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name TXENn RXENn BRGHn ADDENn WAKEn RIEn TIIEn TEIEn R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 TXENn: UARTn Transmitter enable control 0: UARTn Transmitter is disabled 1: UARTn Transmitter is enabled The TXENn bit is the Transmitter Enable Bit. When this bit is equal to "0", the transmitter will be disabled with any pending data transmissions being aborted. In addition the buffers will be reset. If the TXENn bit is equal to "1" and the UARTENn bit is also equal to 1, the transmitter will be enabled and the TXn pin will be controlled by the UARTn. Clearing the TXENn bit during a transmission will cause the data transmission to be aborted and will reset the transmitter. Bit 6 RXENn: UARTn Receiver enable control 0: UARTn Receiver is disabled 1: UARTn Receiver is enabled The RXENn bit is the Receiver Enable Bit. When this bit is equal to "0", the receiver will be disabled with any pending data receptions being aborted. In addition the receiver buffers will be reset. If the RXENn bit is equal to "1" and the UARTENn bit is also equal to 1, the receiver will be enabled and the RXn pin will be controlled by the UARTn. Clearing the RXENn bit during a reception will cause the data reception to be aborted and will reset the receiver. Bit 5 BRGHn: Baud Rate speed selection 0: Low speed baud rate 1: High speed baud rate The bit named BRGHn selects the high or low speed mode of the Baud Rate Generator n. This bit, together with the value placed in the baud rate register, BRGn, controls the baud rate of the UARTn. If the bit is equal to 0, the low speed mode is selected. Bit 4 ADDENn: Address detect function enable control 0: Address detection function is disabled 1: Address detection function is enabled The bit named ADDENn is the address detection function enable control bit. When this bit is equal to 1, the address detection function is enabled. When it occurs, if the 8th bit, which corresponds to RX7n if BNO=0, or the 9th bit, which corresponds to RX8n if BNOn=1, has a value of "1", then the received word will be identified as an address, rather than data. If the corresponding interrupt is enabled, an interrupt request will be generated each time the received word has the address bit set, which is the 8th or 9th bit depending on the value of the BNOn bit. If the address bit known as the 8th or 9th bit of the received word is "0" with the address detection function being enabled, an interrupt will not be generated and the received data will be discarded. 209 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 3 WAKEn: RXn pin falling edge wake-up function enable control 0: RXn pin wake-up UARTn function is disabled 1: RXn pin wake-up UARTn function is enabled The bit is used to control the wake-up UARTn function when a falling edge on the RXn pin occurs. Note that this bit is only available when the UARTn clock, fH, is switched off. There will be no RXn pin wake-up UARTn function if the UARTn clock, fH, exists. If the WAKEn bit is equal to 1 and the UARTn clock, fH, is switched off, a UARTn wake-up request will be initiated when a falling edge on the RXn pin occurs. When this request happens and the corresponding interrupt is enabled, an RXn pin wake-up UARTn interrupt will be generated to inform the MCU to wake up the UARTn function by switching on the UARTn clock, fH, via the application programs. Otherwise, the UARTn function can not resume even if there is a falling edge on the RXn pin when the WAKEn bit is cleared to 0. Bit 2 RIEn: Receiver interrupt enable control 0: Receiver related interrupt is disabled 1: Receiver related interrupt is enabled The bit enables or disables the receiver interrupt. If this bit is equal to 1 and when the receiver overrun flag OERRn or received data available flag RXIFn is set, the UARTn interrupt request flag will be set. If this bit is equal to 0, the UARTn interrupt request flag will not be influenced by the condition of the OERRn or RXIFn flags. Bit 1 TIIEn: Transmitter Idle interrupt enable control 0: Transmitter idle interrupt is disabled 1: Transmitter idle interrupt is enabled The bit enables or disables the transmitter idle interrupt. If this bit is equal to 1 and when the transmitter idle flag TIDLEn is set, due to a transmitter idle condition, the UARTn interrupt request flag will be set. If this bit is equal to 0, the UARTn interrupt request flag will not be influenced by the condition of the TIDLEn flag. Bit 0 TEIEn: Transmitter Empty interrupt enable control 0: Transmitter empty interrupt is disabled 1: Transmitter empty interrupt is enabled The bit enables or disables the transmitter empty interrupt. If this bit is equal to 1 and when the transmitter empty flag TXIFn is set, due to a transmitter empty condition, the UARTn interrupt request flag will be set. If this bit is equal to 0, the UARTn interrupt request flag will not be influenced by the condition of the TXIFn flag. Baud Rate Generator To setup the speed of the serial data communication, the UARTn function contains its own dedicated baud rate generator. The baud rate is controlled by its own internal free running 8-bit timer, the period of which is determined by two factors. The first of these is the value placed in the BRGn register and the second is the value of the BRGHn bit within the UnCR2 control register. The BRGHn bit decides, if the baud rate generator is to be used in a high speed mode or low speed mode, which in turn determines the formula that is used to calculate the baud rate. The value in the BRGn register, N, which is used in the following baud rate calculation formula determines the division factor. Note that N is the decimal value placed in the BRGn register and has a range of between 0 and 255. UnCR2 BRGHn Bit 0 1 Baud Rate (BR) fH / [64 (N+1)] fH / [16 (N+1)] By programming the BRGHn bit which allows selection of the related formula and programming the required value in the BRGn register, the required baud rate can be setup. Note that because the actual baud rate is determined using a discrete value, N, placed in the BRGn register, there will be an error associated between the actual and requested value. The following example shows how the BRGn register value N and the error value can be calculated. Rev. 1.00 210 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM BRGn Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR x x x x x x x x "x": unknown Bit 7~0 D7~D0: Baud Rate values By programming the BRGHn bit in the UnCR2 register which allows selection of the related formula described above and programming the required value in the BRGn register, the required baud rate can be setup. Calculating the Baud Rate and Error Values For a clock frequency of 4MHz, and with BRGHn set to 0 determine the BRGn register value N, the actual baud rate and the error value for a desired baud rate of 4800. From the above table the desired baud rate BR=fH / [64 (N+1)] Re-arranging this equation gives N=[fH / (BR×64)] - 1 Giving a value for N=[4000000 / (4800×64)] - 1=12.0208 To obtain the closest value, a decimal value of 12 should be placed into the BRGn register. This gives an actual or calculated baud rate value of BR=4000000 / [64 × (12+1)]=4808 Therefore the error is equal to (4808 - 4800) / 4800=0.16% UART Setup and Control For data transfer, the UARTn function utilizes a non-return-to-zero, more commonly known as NRZ, format. This is composed of one start bit, eight or nine data bits and one or two stop bits. Parity is supported by the UARTn hardware and can be setup to be even, odd or no parity. For the most common data format, 8 data bits along with no parity and one stop bit, denoted as 8, N, 1, is used as the default setting, which is the setting at power-on. The number of data bits and stop bits, along with the parity, are setup by programming the corresponding BNOn, PRTn, PRENn and STOPSn bits in the UnCR1 register. The baud rate used to transmit and receive data is setup using the internal 8-bit baud rate generator, while the data is transmitted and received LSB first. Although the transmitter and receiver of the UARTn are functionally independent, they both use the same data format and baud rate. In all cases stop bits will be used for data transmission. Enabling/Disabling the UART Interface The basic on/off function of the internal UARTn function is controlled using the UARTENn bit in the UnCR1 register. If the UARTENn, TXENn and RXENn bits are set, then these two UARTn pins will act as normal TXn output pin and RXn input pin respectively. If no data is being transmitted on the TXn pin, then it will default to a logic high value. Clearing the UARTENn bit will disable the TXn and RXn pins and then these two pins can be used as an I/O or other pin-shared functional pins by properly configurations. When the UARTn function is disabled, the buffer will be reset to an empty condition, at the same time discarding any remaining residual data. Disabling the UARTn will also reset the enable control, the error and status flags with bits TXENn, RXENn, TXBRKn, RXIFn, OERRn, FERRn, PERRn and NFn being cleared while bits TIDLEn, TXIFn and RIDLEn will be set. The remaining control bits in the UnCR1, UnCR2 and BRGn registers will remain unaffected. If the UARTENn bit in the UnCR1 register is cleared while the UARTn is active, then all pending transmissions and receptions will be immediately suspended and the UARTn will be reset to a condition as defined above. If the UARTn is then subsequently reenabled, it will restart again in the same configuration. Rev. 1.00 211 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Data, Parity and Stop Bit Selection The format of the data to be transferred is composed of various factors such as data bit length, parity on/off, parity type, address bits and the number of stop bits. These factors are determined by the setup of various bits within the UnCR1 register. The BNOn bit controls the number of data bits which can be set to either 8 or 9. The PRTn bit controls the choice if odd or even parity. The PRENn bit controls the parity on/off function. The STOPSn bit decides whether one or two stop bits are to be used. The following table shows various formats for data transmission. The address bit, which is the MSB of the data byte, identifies the frame as an address character or data if the address detect function is enabled. The number of stop bits, which can be either one or two, is independent of the data length. Start Bit Data Bits Address Bits Parity Bit Stop Bit Example of 8-bit Data Formats 1 8 0 0 1 1 7 0 1 1 1 7 1 0 1 Example of 9-bit Data Formats 1 9 0 0 1 1 8 0 1 1 1 8 1 0 1 Transmitter Receiver Data Format The following diagram shows the transmit and receive waveforms for both 8-bit and 9-bit data formats. Sta�t Bit Pa�ity Bit Bit 0 Bit 1 Bit � Bit 3 Bit 4 Bit 5 Bit � Bit 7 8-bit data format Sta�t Bit Bit 0 Bit 1 Bit � Bit 3 Bit 4 Bit 5 Stop Bit Next Sta�t Bit Pa�ity Bit Bit � Bit 7 Bit 8 Stop Bit Next Sta�t Bit 9-bit data format UART Transmitter Data word lengths of either 8 or 9 bits can be selected by programming the BNOn bit in the UnCR1 register. When BNOn bit is set, the word length will be set to 9 bits. In this case the 9th bit, which is the MSB, needs to be stored in the TX8n bit in the UnCR1 register. At the transmitter core lies the Transmitter Shift Register, more commonly known as the TSRn, whose data is obtained from the transmit data register, which is known as the TXR_RXRn register. The data to be transmitted is loaded into this TXR_RXRn register by the application program. The TSRn register is not written to with new data until the stop bit from the previous transmission has been sent out. As soon as this stop bit has been transmitted, the TSRn can then be loaded with new data from the TXR_RXRn register, if it is available. It should be noted that the TSRn register, unlike many other registers, is not directly mapped into the Data Memory area and as such is not available to the application program for direct read/write operations. An actual transmission of data will normally be enabled when the TXENn bit is set, but the data will not be transmitted until the TXR_RXRn register has been loaded with data and the baud rate generator has defined a shift clock source. However, the transmission can also be initiated by first loading data into the TXR_RXRn register, after which the TXENn bit can be set. When a transmission of data begins, the TSRn is normally empty, in which case a transfer to the TXR_RXRn register will result in an immediate transfer to the TSRn. If during a transmission the TXENn bit is cleared, the transmission will immediately cease and the transmitter will be reset. The TXn output pin can then return to the I/O or other pin-shared function by properly configurations. Rev. 1.00 212 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Transmitting Data When the UARTn is transmitting data, the data is shifted on the TXn pin from the shift register, with the least significant bit LSB first. In the transmit mode, the TXR_RXRn register forms a buffer between the internal bus and the transmitter shift register. It should be noted that if 9-bit data format has been selected, then the MSB will be taken from the TX8n bit in the UnCR1 register. The steps to initiate a data transfer can be summarized as follows: • Make the correct selection of the BNOn, PRTn, PRENn and STOPSn bits to define the required word length, parity type and number of stop bits. • Setup the BRGn register to select the desired baud rate. • Set the TXENn bit to ensure that the UARTn transmitter is enabled and the TXn pin is used as a UARTn transmitter pin. • Access the UnSR register and write the data that is to be transmitted into the TXR_RXRn register. Note that this step will clear the TXIFn bit. This sequence of events can now be repeated to send additional data. It should be noted that when TXIFn=0, data will be inhibited from being written to the TXR_RXRn register. Clearing the TXIFn flag is always achieved using the following software sequence: 1. A UnSR register access 2. A TXR_RXRn register write execution The read-only TXIFn flag is set by the UARTn hardware and if set indicates that the TXR_RXRn register is empty and that other data can now be written into the TXR_RXRn register without overwriting the previous data. If the TEIEn bit is set, then the TXIFn flag will generate an interrupt. During a data transmission, a write instruction to the TXR_RXRn register will place the data into the TXR_RXRn register, which will be copied to the shift register at the end of the present transmission. When there is no data transmission in progress, a write instruction to the TXR_RXRn register will place the data directly into the shift register, resulting in the commencement of data transmission, and the TXIFn bit being immediately set. When a frame transmission is complete, which happens after stop bits are sent or after the break frame, the TIDLEn bit will be set. To clear the TIDLEn bit the following software sequence is used: 1. A UnSR register access 2. A TXR_RXRn register write execution Note that both the TXIFn and TIDLEn bits are cleared by the same software sequence. Transmitting Break If the TXBRKn bit is set, then the break characters will be sent on the next transmission. Break character transmission consists of a start bit, followed by 13xN "0" bits, where N=1, 2, etc. If a break character is to be transmitted, then the TXBRKn bit must be first set by the application program and then cleared to generate the stop bits. Transmitting a break character will not generate a transmit interrupt. Note that a break condition length is at least 13 bits long. If the TXBRKn bit is continually kept at a logic high level, then the transmitter circuitry will transmit continuous break characters. After the application program has cleared the TXBRKn bit, the transmitter will finish transmitting the last break character and subsequently send out one or two stop bits. The automatic logic high at the end of the last break character will ensure that the start bit of the next frame is recognized. Rev. 1.00 213 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM UART Receiver The UARTn is capable of receiving word lengths of either 8 or 9 bits can be selected by programming the BNOn bit in the UnCR1 register. When BNOn bit is set, the word length will be set to 9 bits. In this case the 9th bit, which is the MSB, will be stored in the RX8n bit in the UnCR1 register. At the receiver core lies the Receiver Shift Register more commonly known as the RSRn. The data which is received on the RXn external input pin is sent to the data recovery block. The data recovery block operating speed is 16 times that of the baud rate, while the main receive serial shifter operates at the baud rate. After the RXn pin is sampled for the stop bit, the received data in RSRn is transferred to the receive data register, if the register is empty. The data which is received on the external RXn input pin is sampled three times by a majority detect circuit to determine the logic level that has been placed onto the RXn pin. It should be noted that the RSRn register, unlike many other registers, is not directly mapped into the Data Memory area and as such is not available to the application program for direct read/write operations. Receiving Data When the UARTn receiver is receiving data, the data is serially shifted in on the external RXn input pin to the shift register, with the least significant bit LSB first. The TXR_RXRn register is a two byte deep FIFO data buffer, where two bytes can be held in the FIFO while the 3rd byte can continue to be received. Note that the application program must ensure that the data is read from TXR_RXRn before the 3rd byte has been completely shifted in, otherwise the 3rd byte will be discarded and an overrun error OERRn will be subsequently indicated. The steps to initiate a data transfer can be summarized as follows: • Make the correct selection of the BNOn, PRTn, PRENn and STOPSn bits to define the required word length, parity type and number of stop bits. • Setup the BRGn register to select the desired baud rate. • Set the RXENn bit to ensure that the UARTn receiver is enabled and the RXn pin is used as a UARTn receiver pin. At this point the receiver will be enabled which will begin to look for a start bit. When a character is received, the following sequence of events will occur: • The RXIFn bit in the UnSR register will be set when the TXR_RXRn register has data available. There will be at most one more character that can be read. • When the contents of the shift register have been transferred to the TXR_RXRn register and if the RIEn bit is set, then an interrupt will be generated. • If during reception, a frame error, noise error, parity error or an overrun error has been detected, then the error flags can be set. The RXIFn bit can be cleared using the following software sequence: 1. A UnSR register access 2. A TXR_RXRn register read execution Rev. 1.00 214 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Receiving Break Any break character received by the UARTn will be managed as a framing error. The receiver will count and expect a certain number of bit times as specified by the values programmed into the BNOn and STOPSn bits. If the break is much longer than 13 bit times, the reception will be considered as complete after the number of bit times specified by BNOn and STOPSn. The RXIFn bit is set, FERRn is set, zeros are loaded into the receive data register, interrupts are generated if appropriate and the RIDLEn bit is set. A break is regarded as a character that contains only zeros with the FERRn flag being set. If a long break signal has been detected, the receiver will regard it as a data frame including a start bit, data bits and the invalid stop bit and the FERRn flag will be set. The receiver must wait for a valid stop bit before looking for the next start bit. The receiver will not make the assumption that the break condition on the line is the next start bit. The break character will be loaded into the buffer and no further data will be received until stop bits are received. It should be noted that the RIDLEn read only flag will go high when the stop bits have not yet been received. The reception of a break character on the UARTn registers will result in the following: • The framing error flag, FERRn, will be set. • The receive data register, TXR_RXRn, will be cleared. • The OERRn, NFn, PERRn, RIDLEn or RXIFn flags will possibly be set. Idle Status When the receiver is reading data, which means it will be in between the detection of a start bit and the reading of a stop bit, the receiver status flag in the UnSR register, otherwise known as the RIDLEn flag, will have a zero value. In between the reception of a stop bit and the detection of the next start bit, the RIDLEn flag will have a high value, which indicates the receiver is in an idle condition. Receiver Interrupt The read only receive interrupt flag, RXIFn, in the UnSR register is set by an edge generated by the receiver. An interrupt is generated if RIEn=1, when a word is transferred from the Receive Shift Register, RSRn, to the Receive Data Register, TXR_RXRn. An overrun error can also generate an interrupt if RIEn=1. Managing Receiver Errors Several types of reception errors can occur within the UARTn module, the following section describes the various types and how they are managed by the UARTn. Overrun Error – OERRn The TXR_RXRn register is composed of a two byte deep FIFO data buffer, where two bytes can be held in the FIFO register, while a 3th byte can continue to be received. Before the 3th byte has been entirely shifted in, the data should be read from the TXR_RXRn register. If this is not done, the overrun error flag OERRn will be consequently indicated. In the event of an overrun error occurring, the following will happen: • The OERRn flag in the UnSR register will be set. • The TXR_RXRn contents will not be lost. • The shift register will be overwritten. • An interrupt will be generated if the RIEn bit is set. The OERRn flag can be cleared by an access to the UnSR register followed by a read to the TXR_ RXRn register. Rev. 1.00 215 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Noise Error – NFn Over-sampling is used for data recovery to identify valid incoming data and noise. If noise is detected within a frame, the following will occur: • The read only noise flag, NFn, in the UnSR register will be set on the rising edge of the RXIFn bit. • Data will be transferred from the shift register to the TXR_RXRn register. • No interrupt will be generated. However this bit rises at the same time as the RXIFn bit which itself generates an interrupt. Note that the NFn flag is reset by an UnSR register read operation followed by a TXR_RXRn register read operation. Framing Error – FERRn The read only framing error flag, FERRn, in the UnSR register, is set if a zero is detected instead of stop bits. If two stop bits are selected, both stop bits must be high. Otherwise the FERRn flag will be set. The FERRn flag and the received data will be recorded in the UnSR and TXR_RXRn registers respectively and the FERRn flag will be cleared in any reset. Parity Error – PERRn The read only parity error flag, PERRn, in the UnSR register, is set if the parity of the received word is incorrect. This error flag is only applicable if the parity function is enabled, PRENn=1, and if the parity type, odd or even, is selected. The read only PERRn flag and the received data will be recorded in the UnSR and TXR_RXRn registers respectively and the flag will be cleared on any reset. It should be noted that the FERRn and PERRn flags in the UnSR register should first be read by the application programs before reading the data word. UART Interrupt Structure Several individual UARTn conditions can generate a UARTn interrupt. When these conditions exist, a low pulse will be generated to get the attention of the microcontroller. These conditions are a transmitter data register empty, transmitter idle, receiver data available, receiver overrun, address detect and an RXn pin wake-up. When any of these conditions are created, if its corresponding interrupt control is enabled and the stack is not full, the program will jump to its corresponding interrupt vector where it can be serviced before returning to the main program. Four of these conditions have the corresponding UnSR register flags which will generate a UARTn interrupt if its associated interrupt enable control bit in the UnCR2 register is set. The two transmitter interrupt conditions have their own corresponding enable control bits, while the two receiver interrupt conditions have a shared enable control bit. These enable bits can be used to mask out individual UARTn interrupt sources. The address detect condition, which is also a UARTn interrupt source, does not have an associated flag, but will generate a UARTn interrupt when an address detect condition occurs if its function is enabled by setting the ADDENn bit in the UnCR2 register. An RXn pin wake-up, which is also a UARTn interrupt source, does not have an associated flag, but will generate a UARTn interrupt if the UARTn clock source, fH, is switched off and the WAKEn and RIEn bits in the UnCR2 register are set when a falling edge on the RXn pin occurs. Note that in the event of an RXn wake-up interrupt occurring, there will be a certain period of delay, commonly known as the System Start-up Time, for the oscillator to restart and stabilize before the system resumes normal operation. Rev. 1.00 216 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Note that the UnSR register flags are read only and cannot be cleared or set by the application program, neither will they be cleared when the program jumps to the corresponding interrupt servicing routine, as is the case for some of the other interrupts. The flags will be cleared automatically when certain actions are taken by the UARTn, the details of which are given in the UARTn register section. The overall UARTn interrupt can be disabled or enabled by the related interrupt enable control bits in the interrupt control registers of the microcontroller to decide whether the interrupt requested by the UARTn module is masked out or allowed. UnSR Registe� UnCR� Registe� T�ans�itte� E�pty Flag TXIFn TEIEn T�ans�itte� Idle Flag TIDLEn TIIEn 1 RIEn OR ADDENn Re�eive� Data Availa�le RXIFn WAKEn 0 1 Re�eive� Ove��un Flag OERRn RXn Pin Wake-up 0 UARTn Inte��upt Request Flag URnF URnE 0 EMI 1 0 1 Inte��upt signal to MCU 1 0 1 0 0 0 1 TXR_RXRn.7 if BNO=0 RX8n if BNO=1 1 UnCR� Registe� UARTn Interrupt Structure Address Detect Mode Setting the Address Detect function enable control bit, ADDENn, in the UnCR2 register, enables this special function. If this bit is set to 1, then an additional qualifier will be placed on the generation of a Receiver Data Available interrupt, which is requested by the RXIFn flag. If the ADDENn bit is equal to 1, then when the data is available, an interrupt will only be generated, if the highest received bit has a high value. Note that the related interrupt enable control bit and the EMI bit of the microcontroller must also be enabled for correct interrupt generation. The highest address bit is the 9th bit if the bit BNOn=1 or the 8th bit if the bit BNOn=0. If the highest bit is high, then the received word will be defined as an address rather than data. A Data Available interrupt will be generated every time the last bit of the received word is set. If the ADDENn bit is equal to 0, then a Receive Data Available interrupt will be generated each time the RXIFn flag is set, irrespective of the data last bit status. The address detection and parity functions are mutually exclusive functions. Therefore, if the address detect function is enabled, then to ensure correct operation, the parity function should be disabled by resetting the parity function enable bit PRENn to zero. ADDENn Bit 9 if BNOn=1 Bit 8 if BNOn=0 UARTn Interrupt Generated 0 √ 1 √ 0 1 0 x 1 √ ADDENn Bit Function Rev. 1.00 217 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM UART Power Down and Wake-up When the UARTn clock, fH, is switched off, the UARTn will cease to function. If the MCU switches off the UARTn clock fH and enters the power down mode while a transmission is still in progress, then the transmission will be paused until the UARTn clock source derived from the microcontroller is activated. In a similar way, if the MCU switches off the UART clock fH and enters the power down mode by executing the "HALT" instruction while receiving data, then the reception of data will likewise be paused. When the MCU enters the power down mode, note that the UnSR, UnCR1, UnCR2, transmit and receive registers, as well as the BRGn register will not be affected. It is recommended to make sure first that the UARTn data transmission or reception has been finished before the microcontroller enters the power down mode. The UARTn function contains a receiver RXn pin wake-up function, which is enabled or disabled by the WAKEn bit in the UnCR2 register. If this bit, along with the UARTn enable bit, UARTENn, the receiver enable bit, RXENn and the receiver interrupt bit, RIEn, are all set before the MCU enters the power down mode with the UARTn clock fH being switched off, then a falling edge on the RXn pin will initiate a RXn pin wake-up UARTn interrupt. Note that as it takes certain system clock cycles after a wake-up, before normal microcontroller operation resumes, any data received during this time on the RXn pin will be ignored. For a UARTn wake-up interrupt to occur, in addition to the bits for the wake-up being set, the global interrupt enable bit, EMI, and the UARTn interrupt enable bit, URnE, must be set. If the EMI and URnE bits are not set then only a wake up event will occur and no interrupt will be generated. Note also that as it takes certain system clock cycles after a wake-up before normal microcontroller resumes, the UARTn interrupt will not be generated until after this time has elapsed. Rev. 1.00 218 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Comparators Two independent analog conparators are contained in these devices. The comparator functions offer flexibility via their register controlled features such as power-down, polarity select, response time, etc. In sharing their pins with normal I/O pins the comparators do not waste precious I/O pins if the comparator functions are otherwise unused. CnPOL Cn+ + Cn− − Pin-shared Selection CnOUT CPnINT One Shot CnX Pin-shared Selection CnEN Comparators – n=0~1 Comparator Operation The devices contain two comparator functions which are used to compare two analog voltages and provide an output based on their difference. Full control over the two internal comparators is provided via the control register, CP0C and CP1C, one assigned to each comparator. The comparator output is recorded via a bit in the control register, but can also be transferred out onto a shared I/O pin. Additional comparator functions include output polarity, response time and power down control. Any pull-high resistors connected to the shared comparator input pins will be automatically disconnected when the comparator is enabled. As the comparator inputs approach their switching level, some spurious output signals may be generated on the comparator output due to the slow rising or falling nature of the input signals. This can be minimised by the hysteresis function which will apply a small amount of positive feedback to the comparator. When the comparator operates in the normal mode, the hysteresis function will automatically be enabled. However, the hysteresis function will be disabled when the comparator operates in the input offset calibration mode. Ideally the comparator should switch at the point where the positive and negative inputs signals are at the same voltage level. However, unavoidable input offsets introduce some uncertainties here. The offset calibration function, if executed, will minimise the switching offset value. The comparator also provides the output response time select function using the CNVTn1~CNVTn0 bits in the CPnC register. Comparator Registers There are four registers for overall comparator operation, two registers, CPnC and CPnVOS, for each comparator. As corresponding bits in these registers have identical functions, the following register table applies to the registers. Bit Register Name 7 6 5 4 3 2 1 0 CPnC — CnEN CnPOL CnOUT CNVTn1 CNVTn0 — — CPnVOS — CnOFM CnRSP CnOF4 CnOF3 CnOF2 CnOF1 CnOF0 Comparator Registers List – n=0~1 Rev. 1.00 219 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM CPnC Register Bit 7 6 5 4 3 2 1 0 Name — CnEN CnPOL CnOUT CNVTn1 CNVTn0 — — R/W — R/W R/W R R/W R/W — — POR — 0 0 0 0 0 — — Bit 7 Unimplemented, read as "0" Bit 6 CnEN: Comparator enable control 0: Disable 1: Enable This bit is used to enable the comparator function. If this bit is cleared to zero, the comparator will be switched off and no power consumed even if analog voltages are applied to its inputs. When the comparator function is disabled, the comparator output will be set to zero. Bit 5 CnPOL: Comparator output polarity selection 0: Output not inverted 1: Output inverted If this bit is cleared to zero, the CnOUT bit will reflect the non-inverted output condition of the comparator. If this bit is set high, the CnOUT bit will be inverted. Bit 4 CnOUT: Comparator output bit CnPOL=0 0: Cn+ < Cn– 1: Cn+ > Cn– CnPOL=1 0: Cn+ > Cn– 1: Cn+ < Cn– This bit is used to store the comparator output bit. The polarity of this bit is determined by the voltages on the comparator inputs and by the condition of the CnPOL bit. Bit 3~2 CNVTn1~CNVTn0: Comparator response time selection 00: Response time 0 (max.) 01: Response time 1 10: Response time 2 11: Response time 3 (min.) These bits are used to select the comparator response time. The detailed response time specifications are listed in the Comparator Characteristics. Bit 1~0 Unimplemented, read as "0" CPnVOS Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — CnOFM CnRSP CnOF4 CnOF3 CnOF2 CnOF1 CnOF0 R/W — R/W R/W R/W R/W R/W R/W R/W POR — 0 0 0 0 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 CnOFM: Comparator normal operation or input offset calibration mode selection 0: Normal operation mode 1: Input offset calibration mode This bit is used to enable the comparator input offset calibration function. Refer to the "Input Offset Calibration" section for the detailed input offset calibration procedures. Bit 5 CnRSP: Comparator input offset calibration reference input selection 0: Cn– is selected as reference input 1: Cn+ is selected as reference input 220 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 4~0 CnOF4~CnOF0: Comparator input offset calibration value This 5-bit field is used to perform the comparator input offset calibration operation and the value after the input offset calibration can be restored into this bit field. Refer to the "Input Offset Calibration" section for more detailed information. Input Offset Calibration To operate in the input offset calibration mode, the comparator input pins to be used should first be selected by properly configuring the corresponding pin-shared function selection bits followed by setting the CnOFM bit high. The procedure is described in the following. Step 1. Set CnOFM=1 to enable the comparator input offset calibration mode. Step 2. Set CnOF [4:0]=00000 and read the CnOUT bit. Step 3. Increase the CnOF [4:0] value by 1 and then read the CnOUT bit. If the CnOUT bit state does not changed, then repeat Step 3 until the CnOUT bit state changes. If the CnOUT bit state changes, record the CnOF field value as VCnOS1 and then go to Step 4. Step 4. Set CnOF [4:0]=11111 and read the CnOUT bit. Step 5. Decrease the CnOF [4:0] value by 1 and then read the CnOUT bit. If the CnOUT bit state does not changed, then repeat Step 5 until the CnOUT bit state changes. If the CnOUT bit state changes, record the CnOF field value as VCnOS2 and then go to Step 6. Step 6. Restore the comparator input offset calibration value VCnOS into the CnOF [4:0] bit field. The offset calibration procedure is now finished. Where VCnOS=(VCnOS1+VCnOS2)/2 Comparator Interrupt The comparator interrupt is contained within the Multi-function interrupt. When the comparator output changes state, its relevant interrupt flag will be set, and if the corresponding interrupt enable bit and the Multi-function interrupt enable bit are set, then a jump to its relevant interrupt vector will be executed. Note that it is the changing state of the CnOUT bit and not the output pin which generates an interrupt. If the microcontroller is in the SLEEP or IDLE Mode and the Comparator is enabled, then if the external input lines cause the Comparator output to change state, the resulting generated interrupt flag will also generate a wake-up. If it is required to disable a wake-up from occurring, then the interrupt flag should be first set high before entering the SLEEP or IDLE Mode. Programming Considerations If the comparator is enabled, it will remain active when the microcontroller enters the SLEEP or IDLE Mode, however as it will consume a certain amount of power, the user may wish to consider disabling it before the SLEEP or IDLE Mode is entered. As comparator pins are shared with normal I/O pins the I/O data bits for these pins will be read as zero regardless of the port control register bit value due to normal I/O path being switched off if the comparator function is enabled. Rev. 1.00 221 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCD Driver For large volume applications, which incorporate an LCD in their design, the use of a custom display rather than a more expensive character based display reduces costs significantly. However, the corresponding COM and SEG signals required, which vary in both amplitude and time, to drive such a custom display require many special considerations for proper LCD operation to occur. This device contains an LCD Driver function, which with their internal LCD signal generating circuitry and various options, will automatically generate these time and amplitude varying signals to provide a means of direct driving and easy interfacing to a range of custom LCDs. The device includes a wide range of options to enable LCD displays of various types to be driven. The table shows the range of options available for the device range. Device No. Duty Bias Bias Type Wave Type 1/4 1/3 R or C A or B 1/6 1/3 R or C A or B 1/8 1/3 R A or B 1/4 R A or B HT67F2350 HT67F2360 HT67F2370 HT67F2390 1/8 LCD Selection VDD or V1 VDD or V1 VIN 0.1uF V1 V1 VA=V1=3/2*VIN 0.1uF 0.1uF VA=V1=3*VIN Charge Pump 0.1uF VB=PLCD=2*VIN VC=V2=1/3*VIN V2 V1 VIN Charge Pump VA=V1=VIN VB=PLCD=2/3*VIN VB=PLCD=VIN VC=V2=1/2*VIN 0.1uF 0.1uF 0.1uF Charge Pump VDD or V1 VC=V2=VIN V2 V2 VIN 0.1uF 0.1uF Power Supply from pin PLCD Power Supply from pin V1 Power Supply from pin V2 Note: The pin VMAX must be connected to the maximum voltage to prevent from the pad current leakage. C Type Bias External Power Supply Configuration – 1/3 Bias V1 V1 0.1uF 0.1uF VIN VA=V1=VIN VB=PLCD=2/3*VIN VC=V2=1/3*VIN VA=V1=3/2*VIN 0.1uF VDD VIN VB=PLCD=VIN VC=V2=1/2*VIN V2 V1 VA=V1=3*VIN 0.1uF Charge Pump VB=PLCD=2*VIN V2 VREFIN VIN Charge Pump VC=V2=VIN Power Supply from VB 0.1uF V2 0.1uF 0.1uF 0.1uF Power Supply from VA 0.1uF V1 V1 Charge Pump 0.1uF 0.1uF 0.1uF VDD VDD or V1 Power Supply from VC Note: The pin VMAX must be connected to the maximum voltage to prevent from the pad current leakage. C Type Bias Internal Power Supply Configuration – 1/3 Bias Rev. 1.00 222 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM PLCD VIN PLCD3~PLCD0 QCT�~QCT0 fSUB VA �ont�ol VA Qui�k Cha�ging Cont�ol RSEL�~RSEL0 VB 1/3 Bias Configuration VC RSEL�~RSEL0 LCDEN PLCD VIN PLCD3~PLCD0 QCT�~QCT0 fSUB VA �ont�ol VA Qui�k Cha�ging Cont�ol RSEL�~RSEL0 VB 1/4 Bias Configuration VC VD RSEL�~RSEL0 LCDEN Note: When the R type LCD is disabled, the DC path will be switched off. R Type Bias Configurations – 1/3 Bias & 1/4 Bias Rev. 1.00 223 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM COMn Phase COMn Non-qui�k �ha�ging ti�e Qui�k �ha�ge �ont�ol QT QT: Qui�k �ha�ging ti�e� dete��ined �y QCT [�:0]. Quick Charging Mode LCD Memory An area of Data Memory is especially reserved for use for the LCD display data. This data area is known as the LCD Memory. Any data written here will be automatically read by the internal display driver circuits, which will in turn automatically generate the necessary LCD driving signals. Therefore any data written into this Memory will be immediately reflected into the actual display connected to the microcontroller. Note that for the un-bonded or unused LCD SEG/COM pins the corresponding LCD display memory data bits can be used as general data bits. As the LCD Memory addresses overlap those of the General Purpose Data Memory, it is stored in its own independent Sector 4 area. The Data Memory sector to be used is chosen by using the Memory Pointer high byte register, which is a special function register in the Data Memory, with the name, MP1H or MP2H. To access the LCD Memory therefore requires first that Sector 4 is selected by writing a value of 04H to the MP1H or MP2H register. After this, the memory can then be accessed by using indirect addressing through the use of Memory Pointer low byte, MP1L or MP2L. With Sector 4 selected, then using MP1L or MP2L to read or write to the memory area, starting with address "00H" for all the devices, will result in operations to the LCD Memory. Directly addressing the LCD Display Memory can be applicable using the extended instructions for the full range address access. The accompanying LCD Memory Map diagrams shows how the internal LCD Memory is mapped to the Segments and Commons of the display for the devices. �it 0 �it 1 �it � �it 3 �it 4 �it 5 �it � �it 7 00H SEG0 01H SEG1 0�H SEG� 35H SEG53 3�H SEG54 37H SEG55 COM0 COM1 COM� COM4 COM3 COM5 COM� COM7 LCD Memory Map Rev. 1.00 224 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCD Clock Source The LCD clock source is the internal clock signal, fSUB, divided by 8 using an internal divider circuit. The fSUB internal clock is supplied by either the LIRC or LXT oscillator, the choice of which is determined by a software control bit. For proper LCD operation, this arrangement is provided to generate an ideal LCD clock source frequency of 4 kHz. LCD Register There are control registers, named as LCDC0, LCDC1 and LCDC2, in the Data Memory which is used to control the various setup features of the LCD Driver. Various bits in these registers control functions such as LCD wave type, bias type, supply power selection, total bias resistor selection together with the overall LCD enable and disable control. The LCDEN bit in the LCDC0 register, which provides the overall LCD enable/disable function, will only be effective when the device is in the FAST, SLOW or IDLE Mode. If the device is in the SLEEP Mode then the display will always be disabled. Bits, RSEL2 ~ RSEL0, in the LCDC0 register select the internal total bias resistors to supply the LCD panel with the proper bias current. A choice to best match the LCD panel used in the application can be selected also to minimise bias current. The TYPE bit in the LCDC0 register is used to select whether Type A or Type B LCD waveform signals are used. The RCT bit in the same register is used to select whether R Type or C Type LCD bias is used. The LCDP1 and LCDP0 bits are used to select that the LCD supply power comes from either the external pin or internal power supply for C type bias application. The PLCD3~PLCD0 bits in the LCDC1 register are used to select the VA voltage for R type bias circuitry. The QCT2~QCT0 bits in the same register are used to determine the quick charge time period. Bit Register Name 7 6 5 4 3 2 1 0 LCDC0 TYPE RCT LCDP1 LCDP0 RSEL2 RSEL1 RSEL0 LCDEN LCDC1 QCT2 QCT1 QCT0 — PLCD3 PLCD2 PLCD1 PLCD0 LCDC2 — — — — — DTYC1 DTYC0 BIAS LCD Registers List LCDC0 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name TYPE RCT LCDP1 LCDP0 RSEL2 RSEL1 RSEL0 LCDEN R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 TYPE: LCD waveform type selection 0: Type A 1: Type B Bit 6 RCT: LCD bias type selection 0: R type 1: C type Bit 5~4 LCDP1~LCDP0: C type bias LCD power supply selection 00: From external pin PLCD, V1 or V2 01: From internal reference voltage VREFIN supplied to VC 10: From internal voltage VDD supplied to VB 11: From internal voltage VDD supplied to VA The VREFIN is an internal reference voltage with an approximate level of 1.08V. 225 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 3~1 RSEL2~RSEL0: R type total bias resistors selection – for both 1/3 and 1/4 bias selections 000: 1170 kΩ 001: 225 kΩ 010: 60 kΩ 011: Quick charging mode – switching between 60 kΩ and 1170 kΩ 1xx: Quick charging mode – switching between 60 kΩ and 225 kΩ The device provides the low power quick charging mode for R type LCD display. In quick charging mode the LCD will provide more bias current at the beginning of each COMn phase as LCD display refreshes and then provide less bias current to reduce the bias current consumption in the remaining time duration in the same COMn phase. Bit 0 LCDEN: LCD Enable control 0: Disable 1: Enable In the FAST, SLOW or IDLE mode, the LCD on/off function can be controlled by this bit. However, in the SLEEP mode, the LCD function is always switched off. LCDC1 Register Bit 7 6 5 4 3 2 1 0 Name QCT2 QCT1 QCT0 — PLCD3 PLCD2 PLCD1 PLCD0 R/W R/W R/W R/W — R/W R/W R/W R/W POR 0 0 0 — 0 0 0 0 Bit 7~5 Rev. 1.00 QCT2~QCT0: R type quick charging time selection 000: 1 tSUB 001: 2 tSUB 010: 3 tSUB 011: 4 tSUB 100: 5 tSUB 101: 6 tSUB 110: 7 tSUB 111: 8 tSUB The tSUB is the period of the LCD clock source fSUB, i.e., 1/fSUB. Bit 4 Unimplemented, read as "0" Bit 3~0 PLCD3~PLCD0: R type bias supply voltage selection for VA node 0000: 8/16 × VPLCD 0001: 9/16 × VPLCD 0010: 10/16 × VPLCD 0011: 11/16 × VPLCD 0100: 12/16 × VPLCD 0101: 13/16 × VPLCD 0110: 14/16 × VPLCD 0111: 15/16 × VPLCD 1xxx: VPLCD Note that the VA voltage level has to be equal to or greater than 2.1V. 226 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCDC2 Register Bit 7 6 5 4 3 2 1 0 Name — — — — — DTYC1 DTYC0 BIAS R/W — — — — — R/W R/W R/W POR — — — — — 0 0 0 Bit 7~3 Unimplemented, read as "0" Bit 2~1 DTC1~DTC0: LCD duty selection 00: 1/4 duty – COM0~COM3 used, for both R and C type. 01: 1/6 duty – COM0~COM5 used, for both R and C type. 10: 1/8 duty – COM0~COM7 used, for R type only. 11: Unimplemented The unused COM pin can be configured as other pin-shared functions using the corresponding pin-shared selection register. Bit 0 BIAS: LCD bias selection 0: 1/3 bias – for both R and C types 1: 1/4 bias – for R type only The 1/3 bias selection can be used for both R and C types while the 1/4 bias selection can only be used for R type. It is recommended to use the 1/4 bias selection for the 1/8 duty configuration. LCD Voltage Source and Biasing The time and amplitude varying signals generated by the LCD Driver function require the generation of several voltage levels for their operation. The devices can have either R type or C type biasing selected via a software control bit named RCT. Selecting the C type biasing will enable an internal charge pump circuitry. R Type Biasing – 1/3 Bias & 1/4 Bias For R type biasing an external LCD voltage source must be supplied on pin PLCD to generate the internal biasing voltages. This could be the microcontroller power supply VDD or some other voltage source equal to or less than VDD. For the R type 1/3 bias scheme, four voltage levels VSS, VA, VB and VC are utilised. For the R type 1/4 bias scheme, five voltage levels VSS, VA, VB, VC and VD are utilised. The voltage VA is selected by the PLCD3~PLCD0 bits to be equal to a specific ratio of VPLCD varying from 8/16 VPLCD to VPLCD. Note that the 1/4 bias type is recommended to be used for 1/8 duty selection. Different values of internal bias resistors can be selected using the RSEL2~RESEL0 bits in the LCDC0 register. This along with the voltage on pin PLCD will determine the bias current. The VMAX pin should be connected to the VDD pin and the available maximum voltage applied to the PLCD pin is equal to VDD. Note that no external capacitors or resistors are required to be connected if R type biasing is used. Bias Selection Bias Voltage 1/3 Bias VA=8/16VPLCD ~ VPLCD; VB=2/3VA; VC=1/3VA. 1/4 Bias VA=8/16VPLCD ~ VPLCD; VB=3/4VA; VC=2/4VA; VD=1/4VA. R Type Bias Voltage Rev. 1.00 227 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM C Type Biasing – 1/3 Bias Only For C type biasing the LCD voltage source can be supplied on the external pin PLCD, V1 or V2 or derived from the internal voltage source to generate the required biasing voltages. The C type bias voltage source is selected using the LCDP1 and LCDP0 bits in the LCDC0 register. The C type biasing scheme uses an internal charge pump circuit and can generate voltages higher than what is supplied on PLCD or V2. This feature is useful in applications where the microcontroller supply voltage is less than the supply voltage required by the LCD. Additional charge pump capacitors must also be connected between pins C1 and C2 to generate the necessary voltage levels. For C type 1/3 bias external power supply scheme, the LCD power can be supplied on PLCD, V1 or V2 pin. However, the LCD power is internally supplied on VA, VB or VC for C type 1/3 bias internal power supply scheme. Four internally generated voltage levels, VSS, VA, VB and VC, are utilised. These bias voltages have different levels depending upon different LCD power supply schemes. LCD Power Supply VA voltage VB voltage VC voltage External Power Supply VIN on V1 VIN 2/3 × VIN 1/3 × VIN VIN on PLCD 3/2 × VIN VIN 1/2 × VIN VIN on V2 3 × VIN 2 × VIN VIN Internal Power Supply VDD on VA VDD 2/3 × VDD 1/3 × VDD VDD on VB 3/2 × VDD VDD 1/2 × VDD VREFIN on VC 3 × VREFIN 2 × VREFIN VREFIN C Type Bias Power Supply Scheme The connection to the VMAX pin depends upon the LCD power supply scheme. It is extremely important to ensure that these charge pump generated internal voltages do not exceed the maximum VDD voltage of 5.5V. Condition VMAX Connection VDD > VIN × 1.5 Connect VMAX to VDD Otherwise Connect VMAX to V1 C Type Bias VMAX Pin Connection LCD Reset Function The LCD has an internal reset function that is an OR function of the inverted LCDEN bit in the LCDC0 register and the SLEEP function. When the LCDEN bit is set to 1 to enable the LCD driver function before the device enters the SLEEP mode, the LCD function will be reset after the device enters the SLEEP mode. Clearing the LCDEN bit to zero will also reset the LCD function. MCU Reset SLEEP Mode LCDEN LCD Reset COM & SEG Voltage Level No Off 1 No Normal Operation No Off 0 Yes Low No On x Yes Low Yes x x Yes Floating Note: 1. The watchdog time-out reset in the IDLE or SLEEP Mode is excluded from the MCU Reset conditions. 2. "x": Don’t care. LCD Reset Function Rev. 1.00 228 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCD Driver Output The number of COM and SEG outputs supplied by the LCD driver, as well as its biasing and wave type selections, are dependent upon how the LCD control bits are programmed. The Bias Type, whether C or R type is also selected by a software control bit. The nature of Liquid Crystal Displays require that only AC voltages can be applied to their pixels as the application of DC voltages to LCD pixels may cause permanent damage. For this reason the relative contrast of an LCD display is controlled by the actual RMS voltage applied to each pixel, which is equal to the RMS value of the voltage on the COM pin minus the voltage applied to the SEG pin. This differential RMS voltage must be greater than the LCD saturation voltage for the pixel to be on and less than the threshold voltage for the pixel to be off. The requirement to limit the DC voltage to zero and to control as many pixels as possible with a minimum number of connections requires that both a time and amplitude signal is generated and applied to the application LCD. These time and amplitude varying signals are automatically generated by the LCD driver circuits in the microcontroller. What is known as the duty determines the number of common lines used, which are also known as backplanes or COMs. The duty, which is to have a value of 1/4 and which equates to a COM number of 4, therefore defines the number of time divisions within each LCD signal frame. Two types of signal generation are also provided, known as Type A and Type B, the required type is selected via the TYPE bit in the LCDC0 register. Type B offers lower frequency signals, however, lower frequencies may introduce flickering and influence display clarity. Rev. 1.00 229 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM R and C Type, 4 COM, 1/3 Bias LCD Display Off Mode VA VB VC VSS COM0 ~ COM3 VA VB VC VSS All seng�ent outputs Normal Operation Mode 1 F�a�e VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS COM0 COM1 COM� COM3 All seg�ents a�e OFF COM0 side seg�ents a�e ON COM1 side seg�ents a�e ON COM� side seg�ents a�e ON COM3 side seg�ents a�e ON COM0�1 side seg�ents a�e ON COM0�� side seg�ents a�e ON COM0�3 side seg�ents a�e ON (othe� �o��inations a�e o�itted) VA VB VC VSS All seng�ents a�e ON LCD Driver Output – Type A, 1/4 duty, 1/3 bias Rev. 1.00 230 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCD Display Off Mode VA VB VC VSS COM0 ~ COM3 VA VB VC VSS All seng�ent outputs Normal Operation Mode 1 F�a�e VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS VA VB VC VSS COM0 COM1 COM� COM3 All seg�ents a�e OFF COM0 side seg�ents a�e ON COM1 side seg�ents a�e ON COM� side seg�ents a�e ON COM3 side seg�ents a�e ON COM0�1 side seg�ents a�e ON COM0�� side seg�ents a�e ON COM0�3 side seg�ents a�e ON (othe� �o��inations a�e o�itted) VA VB VC VSS All seng�ents a�e ON LCD Driver Output – Type B, 1/4 duty, 1/3 bias Rev. 1.00 231 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM R and C Type, 6 COM, 1/3 Bias LCD Display Off Mode COM0 ~ COM5 VA VB VC VSS All sengment outputs VA VB VC VSS Normal Operation Mode 1 Frame COM0 VA VB VC VSS COM1 VA VB VC VSS COM2 VA VB VC VSS COM3 VA VB VC VSS COM4 VA VB VC VSS COM5 VA VB VC VSS All segments are OFF VA VB VC VSS COM0 side segments are ON VA VB VC VSS COM1 side segments are ON VA VB VC VSS COM2 side segments are ON VA VB VC VSS COM3 side segments are ON VA VB VC VSS COM4 side segments are ON VA VB VC VSS COM5 side segments are ON VA VB VC VSS COM0,1 side segments are ON VA VB VC VSS COM0,2 side segments are ON VA VB VC VSS COM0,3 side segments are ON VA VB VC VSS COM0,4 side segments are ON VA VB VC VSS COM0,5 side segments are ON VA VB VC VSS VA VB VC VSS All sengments are ON LCD Driver Output – Type A, 1/6 Duty, 1/3 Bias Rev. 1.00 232 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCD Display Off Mode COM0 ~ COM5 VA VB VC VSS All sengment outputs VA VB VC VSS Normal Operation Mode 1 Frame COM0 VA VB VC VSS COM1 VA VB VC VSS COM2 VA VB VC VSS COM3 VA VB VC VSS COM4 VA VB VC VSS COM5 VA VB VC VSS All segments are OFF VA VB VC VSS COM0 side segments are ON VA VB VC VSS COM1 side segments are ON VA VB VC VSS COM2 side segments are ON VA VB VC VSS COM3 side segments are ON VA VB VC VSS COM4 side segments are ON VA VB VC VSS COM5 side segments are ON VA VB VC VSS COM0,1 side segments are ON VA VB VC VSS COM0,2 side segments are ON VA VB VC VSS COM0,3 side segments are ON VA VB VC VSS COM0,4 side segments are ON VA VB VC VSS COM0,5 side segments are ON VA VB VC VSS VA VB VC VSS All sengments are ON LCD Driver Output – Type B, 1/6 Duty, 1/3 Bias Rev. 1.00 233 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM R Type, 8 COM, 1/3 Bias LCD Display Off Mode COM0 ~ COM7 VA VB VC VSS All sengment outputs VA VB VC VSS Normal Operation Mode 1 Frame COM0 VA VB VC VSS COM1 VA VB VC VSS COM2 VA VB VC VSS COM3 VA VB VC VSS COM4 VA VB VC VSS COM5 VA VB VC VSS COM6 VA VB VC VSS COM7 VA VB VC VSS All segments are OFF VA VB VC VSS COM0 side segments are ON VA VB VC VSS COM1 side segments are ON VA VB VC VSS COM2 side segments are ON VA VB VC VSS COM3 side segments are ON VA VB VC VSS COM4 side segments are ON VA VB VC VSS COM5 side segments are ON VA VB VC VSS COM6 side segments are ON VA VB VC VSS COM7 side segments are ON VA VB VC VSS COM0,1 side segments are ON VA VB VC VSS COM0,2 side segments are ON VA VB VC VSS COM0,3 side segments are ON VA VB VC VSS COM0,4 side segments are ON VA VB VC VSS COM0,5 side segments are ON VA VB VC VSS COM0,6 side segments are ON VA VB VC VSS COM0,7 side segments are ON VA VB VC VSS VA VB VC VSS All sengments are ON LCD Driver Output – Type A, 1/8 Duty, 1/3 Bias Rev. 1.00 234 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCD Display Off Mode COM0 ~ COM7 VA VB VC VSS All sengment outputs VA VB VC VSS Normal Operation Mode 1 Frame COM0 VA VB VC VSS COM1 VA VB VC VSS COM2 VA VB VC VSS COM3 VA VB VC VSS COM4 VA VB VC VSS COM5 VA VB VC VSS COM6 VA VB VC VSS COM7 VA VB VC VSS All segments are OFF VA VB VC VSS COM0 side segments are ON VA VB VC VSS COM1 side segments are ON VA VB VC VSS COM2 side segments are ON VA VB VC VSS COM3 side segments are ON VA VB VC VSS COM4 side segments are ON VA VB VC VSS COM5 side segments are ON VA VB VC VSS COM6 side segments are ON VA VB VC VSS COM7 side segments are ON VA VB VC VSS COM0,1 side segments are ON VA VB VC VSS COM0,2 side segments are ON VA VB VC VSS COM0,3 side segments are ON VA VB VC VSS COM0,4 side segments are ON VA VB VC VSS COM0,5 side segments are ON VA VB VC VSS COM0,6 side segments are ON VA VB VC VSS COM0,7 side segments are ON VA VB VC VSS All sengments are ON VA VB VC VSS LCD Driver Output – Type B, 1/8 Duty, 1/3 Bias Rev. 1.00 235 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM R Type, 8 COM, 1/4 Bias 1 Frame LCD segment LCD segment VA VA VB VB COM0 COM0 VC VC State1 State1 (on) (on) VD VD VSS VSS VA VA State2 State2 (off) (off) VB VB COM1 COM1 VC VC VD VD VSS VSS VA VA VB VB COM2 COM2 VC VC VD VD VSS VSS VA VA VB VB COM3 COM3 VC VC VD VD VSS VSS VA VA COM4 COM4 VB VB VC VC VD VD VSS VSS VA VA VB VB COM5 COM5 VC VC VD VD VSS VSS VA VA VB VB COM6 COM6 VC VC VD VD VSS VSS VA VA VB VB COM7 COM7 VC VC VD VD VSS VSS VA VA SEG n SEG n VB VB VC VC VD VD VSS VSS VA VA SEG n+1 SEG n+1 VB VB VC VC VD VD VSS VSS VA VA VB VB SEG n+2 SEG n+2 VC VC VD VD VSS VSS VA VA SEG n+3 SEG n+3 VB VB VC VC VD VD VSS VSS LCD Driver Output – Type A, 1/8 Duty, 1/4 Bias Rev. 1.00 236 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 1 Frame LCD segment LCD segment VA VA VB VB COM0 COM0 VC VC State1 State1 (on) (on) VD VD VSS VSS VA VA COM1 COM1 State2 State2 (off) (off) VB VB VC VC VD VD VSS VSS VA VA VB VB COM2 COM2 VC VC VD VD VSS VSS VA VA VB VB COM3 COM3 VC VC VD VD VSS VSS VA VA COM4 COM4 VB VB VC VC VD VD VSS VSS VA VA COM5 COM5 VB VB VC VC VD VD VSS VSS VA VA VB VB COM6 COM6 VC VC VD VD VSS VSS VA VA COM7 COM7 VB VB VC VC VD VD VSS VSS VA VA VB VB SEG n SEG n VC VC VD VD VSS VSS VA VA VB VB SEG n+1 SEG n+1 VC VC VD VD VSS VSS VA VA SEG n+2 SEG n+2 VB VB VC VC VD VD VSS VSS VA VA SEG n+3 SEG n+3 VB VB VC VC VD VD VSS VSS LCD Driver Output – Type B, 1/8 Duty, 1/4 Bias Rev. 1.00 237 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Programming Considerations Certain precautions must be taken when programming the LCD. One of these is to ensure that the LCD Memory is properly initialised after the microcontroller is powered on. Like the General Purpose Data Memory, the contents of the LCD Memory are in an unknown condition after poweron. As the contents of the LCD Memory will be mapped into the actual display, it is important to initialise this memory area into a known condition soon after applying power to obtain a proper display pattern. Consideration must also be given to the capacitive load of the actual LCD used in the application. As the load presented to the microcontroller by LCD pixels can be generally modeled as mainly capacitive in nature, it is important that this is not excessive, a point that is particularly true in the case of the COM lines which may be connected to many LCD pixels. The accompanying diagram depicts the equivalent circuit of the LCD. One additional consideration that must be taken into account is what happens when the microcontroller enters the IDLE or SLOW Mode. The LCDEN control bit in the LCDC0 register permits the display to be powered off to reduce power consumption. If this bit is zero, the driving signals to the display will cease, producing a blank display pattern but reducing any power consumption associated with the LCD. After Power-on, note that as the LCDEN bit will be cleared to zero, the display function will be disabled. SEG0 SEG1 SEG� SEGn COM0 COM1 COM� COMn LCD Panel Equivalent Circuit Rev. 1.00 238 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 16-bit Multiplication Division Unit – MDU The devices each has a 16-bit Multiplication Division Unit, MDU, which integrates a 16-bit unsigned multiplier and a 32-bit/16-bit divider. The MDU, in replacing the software multiplication and division operations, can therefore save large amounts of computing time as well as the Program and Data Memory space. It also reduces the overall microcontroller loading and results in the overall system performance improvements. fSYS MDUWR0 MDUWR1 MDUWR2 MDUWR3 16/32-bit Dividend / 16-bit Multiplicand MDWEF +/- MDWOV Shift Control 16-bit Divisor / 16-bit Multiplier MDUWR4 MDUWR5 16-Bit MDU Block Diagram MDU Registers The multiplication and division operations are implemented in a specific way, a specific write access sequence of a series of MDU data registers. The status register, MDUWCTRL, provides the indications for the MDU operation. The data register each is used to store the data regarded as the different operand corresponding to different MDU operations. Bit Register Name 7 6 5 4 3 2 1 0 MDUWR0 D7 D6 D5 D4 D3 D2 D1 D0 MDUWR1 D7 D6 D5 D4 D3 D2 D1 D0 MDUWR2 D7 D6 D5 D4 D3 D2 D1 D0 MDUWR3 D7 D6 D5 D4 D3 D2 D1 D0 MDUWR4 D7 D6 D5 D4 D3 D2 D1 D0 MDUWR5 D7 D6 D5 D4 D3 D2 D1 D0 — — — — — — 1 0 MDUWCTRL MDWEF MDWOV MDU Registers List MDUWRn Register – n=0~5 Bit 7 6 5 4 3 2 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR x x x x x x x x "x": unknown Bit 7~0 Rev. 1.00 D7~D0: 16-bit MDU data register n 239 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM MDUWCTRL Register Bit 7 6 5 4 3 2 1 0 Name MDWEF MDWOV — — — — — — R/W R R — — — — — — POR 0 0 — — — — — — Bit 7 MDWEF: 16-bit MDU error flag 0: Normal 1: Abnormal This bit will be set to 1 if the data register MDUWRn is written or read as the MDU operation is executing. This bit should be cleared to 0 by reading the MDUWCTRL register if it is equal to 1 and the MDU operation is completed. Bit 6 MDWOV: 16-bit MDU overflow flag 0: No overflow occurs 1: Multiplication product > FFFFH or Divisor=0 When an operation is completed, this bit will be updated by hardware to a new value corresponding to the current operation situation. Bit 5~0 Unimplemented, read as "0" MDU Operation For this MDU the multiplication or division operation is carried out in a specific way and is determined by the write access sequence of the six MDU data registers, MDUWR0~MDUWR5. The low byte data, regardless of the dividend, multiplicand, divisor or multiplier, must first be written into the corresponding MDU data register followed by the high byte data. All MDU operations will be executed after the MDUWR5 register is write-accessed together with the correct specific write access sequence of the MDUWRn. Note that it is not necessary to consecutively write data into the MDU data registers but must be in a correct write access sequence. Therefore, a non-write MDUWRn instruction or an interrupt, etc., can be inserted into the correct write access sequence without destroying the write operation. The relationship between the write access sequence and the MDU operation is shown in the following. • 32-bit/16-bit division operation: Write data sequentially into the six MDU data registers from MDUWR0 to MDUWR5. • 16-bit/16-bit division operation: Write data sequentially into the specific four MDU data registers in a sequence of MDUWR0, MDUWR1, MDUWR4 and MDUWR5 with no write access to MDUWR2 and MDUWR3. • 16-bit/16-bit multiplication operation: Write data sequentially into the specific four MDU data register in a sequence of MDUWR0, MDUWR4, MDUWR1 and MDUWR5 with no write access to MDUWR2 and MDUWR3. After the specific write access sequence is determined, the MDU will start to perform the corresponding operation. The calculation time necessary for these MDU operations are different. During the calculation time any read/write access to the six MDU data registers is forbidden. After the completion of each operation, it is necessary to check the operation status in the MDUWCTRL register to make sure that whether the operation is correct or not. Then the operation result can be read out from the corresponding MDU data registers in a specific read access sequence if the operation is correctly finished. The necessary calculation time for different MDU operations is listed in the following. • 32-bit/16-bit division operation: 17 × tSYS. • 16-bit/16-bit division operation: 9 × tSYS. • 16-bit/16-bit multiplication operation: 11 × tSYS. Rev. 1.00 240 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM The operation results will be stored in the corresponding MDU data registers and should be read out from the MDU data registers in a specific read access sequence after the operation is completed. Noe that it is not necessary to consecutively read data out from the MDU data registers but must be in a correct read access sequence. Therefore, a non-read MDUWRn instruction or an interrupt, etc., can be inserted into the correct read access sequence without destroying the read operation. The relationship between the operation result read access sequence and the MDU operation is shown in the following. • 32-bit/16-bit division operation: Read the quotient from MDUWR0 to MDUWR3 and remainder from MDUWR4 and MDUWR5 sequentially. • 16-bit/16-bit division operation: Read the quotient from MDUWR0 and MDUWR1 and remainder from MDUWR4 and MDUWR5 sequentially. • 16-bit/16-bit multiplication operation: Read the product sequentially from MDUWR0 to MDUWR3. The overall important points for the MDU read/write access sequence and calculation time are summarized in the following table. Operations Items 32-bit / 16-bit Division 16-bit / 16-bit Division 16-bit x 16-bit Multiplication Write Sequence First write ↓ ↓ ↓ ↓ Last write Dividend Byte 0 written to MDUWR0 Dividend Byte 1 written to MDUWR1 Dividend Byte 2 written to MDUWR2 Dividend Byte 3 written to MDUWR3 Divisor Byte 0 written to MDUWR4 Divisor Byte 1 written to MDUWR5 Dividend Byte 0 written to MDUWR0 Dividend Byte 1 written to MDUWR1 Divisor Byte 0 written to MDUWR4 Divisor Byte 1 written to MDUWR5 Multiplicand Byte 0 written to MDUWR0 Multiplier Byte 0 written to MDUWR4 Multiplicand Byte 1 written to MDUWR1 Multiplier Byte 1 written to MDUWR5 Calculation Time 17 × tSYS 9 × tSYS 11 × tSYS Read Sequence First read ↓ ↓ ↓ ↓ Last read Quotient Byte 0 read from MDUWR0 Quotient Byte 1 read from MDUWR1 Quotient Byte 2 read from MDUWR2 Quotient Byte 3 read from MDUWR3 Remainder Byte 0 read from MDUWR4 Remainder Byte 1 read from MDUWR5 Quotient Byte 0 read from MDUWR0 Quotient Byte 1 read from MDUWR1 Remainder Byte 0 read from MDUWR4 Remainder Byte 1 read from MDUWR5 Product Byte 0 read from MDUWR0 Product Byte 1 read from MDUWR1 Product Byte 2 read from MDUWR2 Product Byte 3 read from MDUWR3 MDU Operations Summary Rev. 1.00 241 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Cyclic Redundancy Check – CRC The Cyclic Redundancy Check, CRC, calculation unit is an error detection technique test algorithm and uses to verify data transmission or storage data correctness. A CRC calculation takes a data stream or a block of data as input and generates a 16-bit output remainder. Ordinarily, a data stream is suffixed by a CRC code and used as a checksum when being sent or stored. Therefore, the received or restored data stream is calculated by the same generator polynomial as described in the following section. POLY CCITT-1� POLY CRCIN CRCDL CRCDH CRC-1� POLY CRC Block Diagram CRC Registers The CRC generator contains an 8-bit CRC data input register, CRCIN, and a CRC checksum register pair, CRCDH and CRCDL. The CRCIN register is used to input new data and the CRCDH and CRCDL registers are used to hold the previous CRC calculation result. A CRC control register, CRCCR, is used to select which CRC generating polynomial is used. Bit Register Name 7 6 5 4 3 2 1 0 CRCIN D7 D6 D5 D4 D3 D2 D1 D0 D0 CRCDL D7 D6 D5 D4 D3 D2 D1 CRCDH D7 D6 D5 D4 D3 D2 D1 D0 CRCCR — — — — — — — POLY CRC Registers List CRCIN Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 D7~D0: CRC input data register CRCDL Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 Rev. 1.00 D7~D0: 16-bit CRC checksum low byte data register 242 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM CRCDH Register Bit 7 6 5 4 3 2 1 0 Name D7 D6 D5 D4 D3 D2 D1 D0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~0 D7~D0: 16-bit CRC checksum high byte data register CRCCR Register Bit 7 6 5 4 3 2 1 0 Name — — — — — — — POLY R/W — — — — — — — R/W POR — — — — — — — 0 Bit 7~1 Unimplemented, read as "0" Bit 0 POLY: 16-bit CRC generating polynomial selection 0: CRC-CCITT: X16 + X12 + X5 + 1 1: CRC-16: X16 + X15 + X2 + 1 CRC Operation The CRC generator provides the 16-bit CRC result calculation based on the CRC16 and CCITT CRC16 polynomials. In this CRC generator, there are only these two polynomials available for the numeric values calculation. It can not support the 16-bit CRC calculations based on any other polynomials. The following two expressions can be used for the CRC generating polynomial which is determined using the POLY bit in the CRC control register, CRCCR. The CRC calculation result is called as the CRC checksum, CRCSUM, and stored in the CRC checksum register pair, CRCDH and CRCDL. • CRC-CCITT: X16 + X12 + X5 + 1. • CRC-16: X16 + X15 + X2 + 1. CRC Computation Each write operation to the CRCIN register creates a combination of the previous CRC value stored in the CRCDH and CRCDL registers and the new data input. The CRC unit calculates the CRC data register value is based on byte by byte. It will take one MCU instruction cycle to calculate the CRC checksum. • CRC Calculation Procedures: • Clear the checksum register pair, CRCDH and CRCDL. • Execute an "Exclusive OR" operation with the 8-bit input data byte and the 16-bit CRCSUM high byte. The result is called the temporary CRCSUM. • Shift the temporary CRCSUM value left by one bit and move a "0" into the LSB. • Check the shifted temporary CRCSUM value after procedure 3. If the MSB is 0, then this shifted temporary CRCSUM will be considered as a new temporary CRCSUM. Otherwise, execute an "Exclusive OR" operation with the shifted temporary CRCSUM in procedure 3 and a data "8005H". Then the operation result will be regarded as the new temporary CRCSUM. Note that the data to be perform an "Exclusive OR" operation is "8005H" for the CRC-16 polynomial while for the CRC-CCITT polynomial the data is "1021H". • Repeat the procedure 3 ~ procedure 4 until all bits of the input data byte are completely calculated. • Repeat the procedure 2~ procedure 5 until all of the input data bytes are completely calculated. Then, the latest calculated result is the final CRC checksum, CRCSUM. Rev. 1.00 243 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM • CRC Calculation Examples: • Write 1 byte input data into the CRCIN register and the corresponding CRC checksum are individually calculated as the following table shown. CRC Data Input CRC Polynomial CRC-CCITT (X16+X12+X5+1) CRC-16 (X +X +X +1) 16 15 2 00H 01H 02H 03H 04H 05H 06H 0000H 1021H 2042H 3063H 4084H 50A5H 60C6H 70E7H 0000H 8005H 800FH 000AH 801BH 001EH 0014H 07H 8011H Note: The initial value of the CRC checksum register pair, CRCDH and CRCDL, is zero before each CRC input data is written into the CRCIN register. • Write 4 bytes input data into the CRCIN register sequentially and the CRC checksum are sequentially listed in the following table. CRC Data Input CRC Polynomial CRCIN=78H→56H→34H→12H CRC-CCITT (X16+X12+X5+1) (CRCDH, CRCDL)=FF9FH→BBC3H→A367H→D0FAH CRC-16 (X16+X15+X2+1) (CRCDH, CRCDL)=0110h→91F1h→F2DEh→5C43h Note: The initial value of the CRC checksum register pair, CRCDH and CRCDL, is zero before the sequential CRC data input operation. • Program Memory CRC Checksum Calculation Example: • Clear the checksum register pair, CRCDH and CRCDL. • Select the CRC-CCITT or CRC-16 polynomial as the generating polynomial using the POLY bit in the CRCCR register. • Execute the table read instruction to read the program memory data value. • Write the table data low byte into the CRCIN register and execute the CRC calculation with the current CRCSUM value. Then a new CRCSUM result will be obtained and stored in the CRC checksum register pair, CRCDH and CRCDL. • Write the table data high byte into the CRCIN register and execute the CRC calculation with the current CRCSUM value. Then a new CRCSUM result will be obtained and stored in the CRC checksum register pair, CRCDH and CRCDL. • Repeat the procedure 3 ~ procedure 5 to read the next program memory data value and execute the CRC calculation until all program memory data are read followed by the sequential CRC calculation. Then the value in the CRC checksum register pair is the final CRC calculation result. Rev. 1.00 244 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Low Voltage Detector – LVD Each device has a Low Voltage Detector function, also known as LVD. This enabled the device to monitor the power supply voltage, VDD, and provide a warning signal should it fall below a certain level. This function may be especially useful in battery applications where the supply voltage will gradually reduce as the battery ages, as it allows an early warning battery low signal to be generated. The Low Voltage Detector also has the capability of generating an interrupt signal. LVD Register The Low Voltage Detector function is controlled using a single register with the name LVDC. Three bits in this register, VLVD2~VLVD0, are used to select one of eight fixed voltages below which a low voltage condition will be determined. A low voltage condition is indicated when the LVDO bit is set. If the LVDO bit is low, this indicates that the VDD voltage is above the preset low voltage value. The LVDEN bit is used to control the overall on/off function of the low voltage detector. Setting the bit high will enable the low voltage detector. Clearing the bit to zero will switch off the internal low voltage detector circuits. As the low voltage detector will consume a certain amount of power, it may be desirable to switch off the circuit when not in use, an important consideration in power sensitive battery powered applications. LVDC Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — — LVDO LVDEN VBGEN VLVD2 VLVD1 VLVD0 R/W — — R R/W R/W R/W R/W R/W POR — — 0 0 0 0 0 0 Bit 7~6 Unimplemented, read as "0" Bit 5 LVDO: LVD output flag 0: No Low Voltage Detected 1: Low Voltage Detected Bit 4 LVDEN: Low Voltage Detector Enable control 0: Disable 1: Enable Bit 3 VBGEN: Bandgap Voltage Output Enable control 0: Disable 1: Enable Note that the Bandgap circuit is enabled when the LVD or LVR function is enabled or when the VBGEN bit is set to 1. Bit 2~0 VLVD2~VLVD0: LVD Voltage selection 000: 2.0V 001: 2.2V 010: 2.4V 011: 2.7V 100: 3.0V 101: 3.3V 110: 3.6V 111: 4.0V 245 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LVD Operation The Low Voltage Detector function operates by comparing the power supply voltage, VDD, with a pre-specified voltage level stored in the LVDC register. This has a range of between 2.0V and 4.0V. When the power supply voltage, VDD, falls below this pre-determined value, the LVDO bit will be set high indicating a low power supply voltage condition. The Low Voltage Detector function is supplied by a reference voltage which will be automatically enabled. When the device enters the SLEEP Mode, the low voltage detector will automatically be disabled even if the LVDEN bit is high. After enabling the Low Voltage Detector, a time delay tLVDS should be allowed for the circuitry to stabilise before reading the LVDO bit. Note also that as the VDD voltage may rise and fall rather slowly, at the voltage nears that of VLVD, there may be multiple bit LVDO transitions. VDD VLVD LVDEN LVDO tLVDS LVD Operation The Low Voltage Detector also has its own interrupt which is contained within one of the Multifunction interrupts, providing an alternative means of low voltage detection, in addition to polling the LVDO bit. The interrupt will only be generated after a delay of tLVD after the LVDO bit has been set high by a low voltage condition. When the device is powered down the Low Voltage Detector will remain active if the LVDEN bit is high. In this case, the LVF interrupt request flag will be set, causing an interrupt to be generated if VDD falls below the preset LVD voltage. This will cause the device to wake-up from the IDLE Mode. However, if the Low Voltage Detector wake up function is not required, then the LVF flag should be first set high before the device enters the IDLE Mode. Rev. 1.00 246 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Interrupts Interrupts are an important part of any microcontroller system. When an external event or an internal function such as a Timer Module or an A/D converter requires microcontroller attention, their corresponding interrupt will enforce a temporary suspension of the main program allowing the microcontroller to direct attention to their respective needs. These devices contain several external interrupt and internal interrupts functions. The external interrupts are generated by the action of the external INT0 ~ INT3 pins, while the internal interrupts are generated by various internal functions such as the TMs, Time Base, LVD, EEPROM, SIM, UART and the A/D converter, etc. Interrupt Registers Overall interrupt control, which basically means the setting of request flags when certain microcontroller conditions occur and the setting of interrupt enable bits by the application program, is controlled by a series of registers, located in the Special Purpose Data Memory, as shown in the accompanying table. The number of registers depends upon the device chosen but fall into three categories. The first is the INTC0~INTC3 registers which setup the primary interrupts, the second is the MFI0~MFI9 registers which setup the Multi-function interrupts. Finally there is an INTEG register to setup the external interrupt trigger edge type. Each register contains a number of enable bits to enable or disable individual interrupts as well as interrupt flags to indicate the presence of an interrupt request. The naming convention of these follows a specific pattern. First is listed an abbreviated interrupt type, then the (optional) number of that interrupt followed by either an "E" for enable/disable bit or "F" for request flag. Function Global INTn Pins Enable Bit Request Flag Notes EMI — — INTnE INTnF n=0 ~ 3 A/D Converter ADE ADF — Multi-function MFnE MFnF n=0 ~ 9 Comparator CPnE CPnF n=0 ~ 1 Time Base TBnE TBnF n=0 ~ 1 LVE LVF — LVD EEPROM write operation DEE DEF — SIM SIME SIMF — SPIA SPIAE SPIAF — URnE URnF n=0 ~ 1 (HT67F2350/HT67F2360) n=0 ~ 2 (HT67F2370/HT67F2390) PTMnPE PTMnPF PTMnAE PTMnAF STMnPE STMnPF STMnAE STMnAF UART PTM STM n=0 ~ 7 n=0 ~ 2 Interrupt Register Bit Naming Conventions Rev. 1.00 247 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit Register Name INTEG 7 6 5 4 3 2 1 0 INT3S1 INT3S0 INT2S1 INT2S0 INT1S1 INT1S0 INT0S1 INT0S0 INTC0 — MF6F INT1F INT0F MF6E INT1E INT0E EMI INTC1 ADF MF1F MF0F MF7F ADE MF1E MF0E MF7E INTC2 MF3F MF9F MF8F MF2F MF3E MF9E MF8E MF2E INTC3 MF5F MF4F INT3F INT2F MF5E MF4E INT3E INT2E MFI0 STM0AF STM0PF PTM0AF PTM0PF STM0AE STM0PE PTM0AE PTM0PE MFI1 STM1AF STM1PF PTM1AF PTM1PF STM1AE STM1PE PTM1AE PTM1PE MFI2 — — MFI3 SIMF SPIAF PTM2AF PTM2PF DEF LVF — — SIME SPIAE PTM2AE PTM2PE DEE LVE STM2AF STM2PF PTM3AF PTM3PF STM2AE STM2PE PTM3AE PTM3PE MFI4 MFI5 (HT67F2350/ HT67F2360) — — UR1F UR0F — — UR1E UR0E MFI5 (HT67F2370/ HT67F2390) — UR2F UR1F UR0F — UR2E UR1E UR0E MFI6 — CP0F PTM4AF PTM4PF — CP0E PTM4AE PTM4PE MFI7 — CP1F PTM5AF PTM5PF — CP1E PTM5AE PTM5PE MFI8 — TB0F PTM6AF PTM6PF — TB0E PTM6AE PTM6PE MFI9 — TB1F PTM7AF PTM7PF — TB1E PTM7AE PTM7PE Interrupt Registers List INTEG Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name INT3S1 INT3S0 INT2S1 INT2S0 INT1S1 INT1S0 INT0S1 INT0S0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 INT3S1~INT3S0: Interrupt edge control for INT3 pin 00: Disable 01: Rising edge 10: Falling edge 11: Rising and falling edges Bit 5~4 INT2S1~INT2S0: Interrupt edge control for INT2 pin 00: Disable 01: Rising edge 10: Falling edge 11: Rising and falling edges Bit 3~2 INT1S1~INT1S0: Interrupt edge control for INT1 pin 00: Disable 01: Rising edge 10: Falling edge 11: Rising and falling edges Bit 1~0 INT0S1~INT0S0: Interrupt edge control for INT0 pin 00: Disable 01: Rising edge 10: Falling edge 11: Rising and falling edges 248 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM INTC0 Register Bit 7 6 5 4 3 2 1 0 Name — MF6F INT1F INT0F MF6E INT1E INT0E EMI R/W — R/W R/W R/W R/W R/W R/W R/W POR — 0 0 0 0 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 MF6F: Multi-function 6 interrupt request flag 0: No request 1: Interrupt request Bit 5 INT1F: INT1 interrupt request flag 0: No request 1: Interrupt request Bit 4 INT0F: INT0 interrupt request flag 0: No request 1: Interrupt request Bit 3 MF6E: Multi-function 6 interrupt control 0: Disable 1: Enable Bit 2 INT1E: INT1 interrupt control 0: Disable 1: Enable Bit 1 INT0E: INT0 interrupt control 0: Disable 1: Enable Bit 0 EMI: Global interrupt control 0: Disable 1: Enable INTC1 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name ADF MF1F MF0F MF7F ADE MF1E MF0E MF7E R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 ADF: A/D Converter interrupt request flag 0: No request 1: Interrupt request Bit 6 MF1F: Multi-function 1 interrupt request flag 0: No request 1: Interrupt request Bit 5 MF0F: Multi-function 0 interrupt request flag 0: No request 1: Interrupt request Bit 4 MF7F: Multi-function 7 interrupt request flag 0: No request 1: Interrupt request Bit 3 ADE: A/D Converter interrupt control 0: Disable 1: Enable Bit 2 MF1E: Multi-function 1 interrupt control 0: Disable 1: Enable 249 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 1 MF0E: Multi-function 0 interrupt control 0: Disable 1: Enable Bit 0 MF7E: Multi-function 7 interrupt control 0: Disable 1: Enable INTC2 Register Bit 7 6 5 4 3 2 1 0 Name MF3F MF9F MF8F MF2F MF3E MF9E MF8E MF2E R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 MF3F: Multi-function 3 interrupt request flag 0: No request 1: Interrupt request Bit 6 MF9F: Multi-function 9 interrupt request flag 0: No request 1: Interrupt request Bit 5 MF8F: Multi-function 8 interrupt request flag 0: No request 1: Interrupt request Bit 4 MF2F: Multi-function 2 interrupt request flag 0: No request 1: Interrupt request Bit 3 MF3E: Multi-function 3 interrupt control 0: Disable 1: Enable Bit 2 MF9E: Multi-function 9 interrupt control 0: Disable 1: Enable Bit 1 MF8E: Multi-function 8 interrupt control 0: Disable 1: Enable Bit 0 MF2E: Multi-function 2 interrupt control 0: Disable 1: Enable INTC3 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name MF5F MF4F INT3F INT2F MF5E MF4E INT3E INT2E R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 MF5F: Multi-function 5 interrupt request flag 0: No request 1: Interrupt request Bit 6 MF4F: Multi-function 4 interrupt request flag 0: No request 1: Interrupt request Bit 5 INT3F: INT3 interrupt request flag 0: No request 1: Interrupt request 250 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 4 INT2F: INT2 interrupt request flag 0: No request 1: Interrupt request Bit 3 MF5E: Multi-function 5 interrupt control 0: Disable 1: Enable Bit 2 MF4E: Multi-function 4 interrupt control 0: Disable 1: Enable Bit 1 INT3E: INT3 interrupt control 0: Disable 1: Enable Bit 0 INT2E: INT2 interrupt control 0: Disable 1: Enable MFI0 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name STM0AF STM0PF PTM0AF PTM0PF STM0AE STM0PE PTM0AE PTM0PE R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 STM0AF: STM0 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 6 STM0PF: STM0 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 5 PTM0AF: PTM0 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 4 PTM0PF: PTM0 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 3 STM0AE: STM0 Comparator A match Interrupt control 0: Disable 1: Enable Bit 2 STM0PE: STM0 Comparator P match Interrupt control 0: Disable 1: Enable Bit 1 PTM0AE: PTM0 Comparator A match Interrupt control 0: Disable 1: Enable Bit 0 PTM0PE: PTM0 Comparator P match Interrupt control 0: Disable 1: Enable 251 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM MFI1 Register Bit 7 6 5 4 3 2 1 0 Name STM1AF STM1PF PTM1AF PTM1PF STM1AE STM1PE PTM1AE PTM1PE R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 STM1AF: STM1 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 6 STM1PF: STM1 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 5 PTM1AF: PTM1 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 4 PTM1PF: PTM1 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 3 STM1AE: STM1 Comparator A match Interrupt control 0: Disable 1: Enable Bit 2 STM1PE: STM1 Comparator P match Interrupt control 0: Disable 1: Enable Bit 1 PTM1AE: PTM1 Comparator A match Interrupt control 0: Disable 1: Enable Bit 0 PTM1PE: PTM1 Comparator P match Interrupt control 0: Disable 1: Enable MFI2 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — — PTM2AF PTM2PF — — PTM2AE PTM2PE R/W — — R/W R/W — — R/W R/W POR — — 0 0 — — 0 0 Bit 7~6 Unimplemented, read as "0" Bit 5 PTM2AF: PTM2 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 4 PTM2PF: PTM2 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 3~2 Unimplemented, read as "0" Bit 1 PTM2AE: PTM2 Comparator A match Interrupt control 0: Disable 1: Enable Bit 0 PTM2PE: PTM2 Comparator P match Interrupt control 0: Disable 1: Enable 252 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM MFI3 Register Bit 7 6 5 4 3 2 1 0 Name SIMF SPIAF DEF LVF SIME SPIAE DEE LVE R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 SIMF: SIM Interrupt request flag 0: No request 1: Interrupt request Bit 6 SPIAF: SPIA Interrupt request flag 0: No request 1: Interrupt request Bit 5 DEF: Data EEPROM Interrupt request flag 0: No request 1: Interrupt request Bit 4 LVF: LVD Interrupt request flag 0: No request 1: Interrupt request Bit 3 SIME: SIM Interrupt control 0: Disable 1: Enable Bit 2 SPIAE: SPIA Interrupt control 0: Disable 1: Enable Bit 1 DEE: Data EEPROM Interrupt control 0: Disable 1: Enable Bit 0 LVE: LVD Interrupt control 0: Disable 1: Enable MFI4 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name STM2AF STM2PF PTM3AF PTM3PF STM2AE STM2PE PTM3AE PTM3PE R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7 STM2AF: STM2 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 6 STM2PF: STM2 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 5 PTM3AF: PTM3 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 4 PTM3PF: PTM3 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 3 STM2AE: STM2 Comparator A match Interrupt control 0: Disable 1: Enable 253 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 2 STM2PE: STM2 Comparator P match Interrupt control 0: Disable 1: Enable Bit 1 PTM3AE: PTM3 Comparator A match Interrupt control 0: Disable 1: Enable Bit 0 PTM3PE: PTM3 Comparator P match Interrupt control 0: Disable 1: Enable MFI5 Register – HT67F2350/HT67F2360 Bit 7 6 5 4 3 2 1 0 Name — — UR1F UR0F — — UR1E UR0E R/W — — R/W R/W — — R/W R/W POR — — 0 0 — — 0 0 Bit 7~6 Unimplemented, read as "0" Bit 5 UR1F: UART1 transfer interrupt request flag 0: No request 1: Interrupt request Bit 4 UR0F: UART0 transfer interrupt request flag 0: No request 1: Interrupt request Bit 3~2 Unimplemented, read as "0" Bit 1 UR1E: UART1 transfer interrupt control 0: Disable 1: Enable Bit 0 UR0E: UART0 transfer interrupt control 0: Disable 1: Enable MFI5 Register – HT67F2370/HT67F2390 Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — UR2F UR1F UR0F — UR2E UR1E UR0E R/W — R/W R/W R/W — R/W R/W R/W POR — 0 0 0 — 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 UR2F: UART2 transfer interrupt request flag 0: No request 1: Interrupt request Bit 5 UR1F: UART1 transfer interrupt request flag 0: No request 1: Interrupt request Bit 4 UR0F: UART0 transfer interrupt request flag 0: No request 1: Interrupt request Bit 3 Unimplemented, read as "0" Bit 2 UR2E: UART2 transfer interrupt control 0: Disable 1: Enable 254 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 1 UR1E: UART1 transfer interrupt control 0: Disable 1: Enable Bit 0 UR0E: UART0 transfer interrupt control 0: Disable 1: Enable MFI6 Register Bit 7 6 5 4 3 2 1 0 Name — CP0F PTM4AF PTM4PF — CP0E PTM4AE PTM4PE R/W — R/W R/W R/W — R/W R/W R/W POR — 0 0 0 — 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 CP0F: Comparator 0 interrupt request flag 0: No request 1: Interrupt request Bit 5 PTM4AF: PTM4 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 4 PTM4PF: PTM4 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 3 Unimplemented, read as "0" Bit 2 CP0E: Comparator 0 interrupt control 0: Disable 1: Enable Bit 1 PTM4AE: PTM4 Comparator A match Interrupt control 0: Disable 1: Enable Bit 0 PTM4PE: PTM4 Comparator P match Interrupt control 0: Disable 1: Enable MFI7 Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name — CP1F PTM5AF PTM5PF — CP1E PTM5AE PTM5PE R/W — R/W R/W R/W — R/W R/W R/W POR — 0 0 0 — 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 CP1F: Comparator 1 interrupt request flag 0: No request 1: Interrupt request Bit 5 PTM5AF: PTM5 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 4 PTM5PF: PTM5 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 3 Unimplemented, read as "0" 255 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 2 CP1E: Comparator 1 interrupt control 0: Disable 1: Enable Bit 1 PTM5AE: PTM5 Comparator A match Interrupt control 0: Disable 1: Enable Bit 0 PTM5PE: PTM5 Comparator P match Interrupt control 0: Disable 1: Enable MFI8 Register Bit 7 6 5 4 3 2 1 0 Name — TB0F PTM6AF PTM6PF — TB0E PTM6AE PTM6PE R/W — R/W R/W R/W — R/W R/W R/W POR — 0 0 0 — 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 TB0F: Time Base 0 interrupt request flag 0: No request 1: Interrupt request Bit 5 PTM6AF: PTM6 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 4 PTM6PF: PTM6 Comparator P match Interrupt request flag 0: No request 1: Interrupt request Bit 3 Unimplemented, read as "0" Bit 2 TB0E: Time Base 0 interrupt control 0: Disable 1: Enable Bit 1 PTM6AE: PTM6 Comparator A match Interrupt control 0: Disable 1: Enable Bit 0 PTM6PE: PTM6 Comparator P match Interrupt control 0: Disable 1: Enable MFI9 Register Bit Rev. 1.00 7 6 5 4 3 2 1 0 Name — TB1F PTM7AF R/W — R/W R/W PTM7PF — TB1E PTM7AE PTM7PE R/W — R/W R/W POR — 0 0 R/W 0 — 0 0 0 Bit 7 Unimplemented, read as "0" Bit 6 TB1F: Time Base 1 interrupt request flag 0: No request 1: Interrupt request Bit 5 PTM7AF: PTM7 Comparator A match Interrupt request flag 0: No request 1: Interrupt request Bit 4 PTM7PF: PTM7 Comparator P match Interrupt request flag 0: No request 1: Interrupt request 256 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Bit 3 Unimplemented, read as "0" Bit 2 TB1E: Time Base 1 interrupt control 0: Disable 1: Enable Bit 1 PTM7AE: PTM7 Comparator A match Interrupt control 0: Disable 1: Enable Bit 0 PTM7PE: PTM7 Comparator P match Interrupt control 0: Disable 1: Enable Interrupt Operation When the conditions for an interrupt event occur, such as a TM Comparator P or Comparator A or A/D conversion completion, etc, the relevant interrupt request flag will be set. Whether the request flag actually generates a program jump to the relevant interrupt vector is determined by the condition of the interrupt enable bit. If the enable bit is set high then the program will jump to its relevant vector; if the enable bit is zero then although the interrupt request flag is set an actual interrupt will not be generated and the program will not jump to the relevant interrupt vector. The global interrupt enable bit, if cleared to zero, will disable all interrupts. When an interrupt is generated, the Program Counter, which stores the address of the next instruction to be executed, will be transferred onto the stack. The Program Counter will then be loaded with a new address which will be the value of the corresponding interrupt vector. The microcontroller will then fetch its next instruction from this interrupt vector. The instruction at this vector will usually be a JMP which will jump to another section of program which is known as the interrupt service routine. Here is located the code to control the appropriate interrupt. The interrupt service routine must be terminated with a RETI, which retrieves the original Program Counter address from the stack and allows the microcontroller to continue with normal execution at the point where the interrupt occurred. The various interrupt enable bits, together with their associated request flags, are shown in the accompanying diagrams with their order of priority. Some interrupt sources have their own individual vector while others share the same multi-function interrupt vector. Once an interrupt subroutine is serviced, all other interrupts will be blocked, as the global interrupt enable bit, EMI bit will be cleared automatically. This will prevent any further interrupt nesting from occurring. However, if other interrupt requests occur during this interval, although the interrupt will not be immediately serviced, the request flag will still be recorded. If an interrupt requires immediate servicing while the program is already in another interrupt service routine, the EMI bit should be set after entering the routine to allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged, even if the related interrupt is enabled, until the Stack Pointer is decremented. If immediate service is desired, the stack must be prevented from becoming full. In case of simultaneous requests, the accompanying diagram shows the priority that is applied. All of the interrupt request flags when set will wake-up the device if it is in SLEEP or IDLE Mode, however to prevent a wake-up from occurring the corresponding flag should be set before the device is in SLEEP or IDLE Mode. Rev. 1.00 257 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Interrupts contained within Multi-Function Interrupts PTM4PE PTM4 P PTM4PF PTM4 A PTM4AF PTM4AE Legend Request Flag, no auto reset in ISR Comp. 0 CP0F CP0E xxF xxF Request Flag, auto reset in ISR PTM5 P PTM5PF PTM5PE xxE Enable Bits PTM5 A PTM5AF PTM5AE Comp. 1 CP1F CP1E STM0 P STM0PF STM0PE STM0 A STM0AF STM0AE PTM0 P PTM0PF PTM0PE PTM0 A PTM0AF PTM0AE STM1 P STM1PF STM1PE STM1 A STM1AF STM1AE PTM1 P PTM1PF PTM1PE PTM1 A PTM1AF PTM1AE PTM2 P PTM2PF PTM2PE PTM2 A PTM2AF PTM2AE PTM6 P PTM6PF PTM6PE PTM6 A PTM6AF PTM6AE T.B. 0 TB0F TB0E PTM7 P PTM7PF PTM7PE PTM7 A PTM7AF PTM7AE T.B. 1 TB1F TB1E LVD LVF LVE EEPROM DEF DEE SPIA SPIAF SPIAE SIM SIMF SIME STM2 P STM2PF STM2PE STM2 A STM2AF STM2AE PTM3 P PTM3PF PTM3PE PTM3 A PTM3AF PTM3AE UART 0 UR0F UR0E UART 1 UR1F UR1E *UART 2 *UR2F *UR2E EMI auto disabled in ISR Interrupt Name Request Flags Enable Bits Master Enable INT0 Pin INT0F INT0E EMI INT1 Pin INT1F INT1E EMI 08H M. Funct. 6 MF6F MF6E EMI 0CH M. Funct. 7 MF7F MF7E EMI 10H M. Funct. 0 MF0F MF0E EMI 14H M. Funct. 1 MF1F MF1E EMI 18H A/D ADF ADE EMI 1CH M. Funct. 2 MF2F MF2E EMI 20H M. Funct. 8 MF8F MF8E EMI 24H M. Funct. 9 MF9F MF9E EMI 28H M. Funct. 3 MF3F MF3E EMI 2CH INT2 Pin INT2F INT2E EMI 30H INT3 Pin INT3F INT3E EMI 34H M. Funct. 4 MF4F MF4E EMI 38H M. Funct. 5 MF5F MF5E EMI 3CH Vector Priority High 04H Low * The UART 2 interrupt exists only in HT67F2370/HT67F2390. Interrupt Scheme – HT67F2350/HT67F2360/ HT67F2370/HT67F2390 Rev. 1.00 258 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM External Interrupt The external interrupts are controlled by signal transitions on the pins INT0~INT3. An external interrupt request will take place when the external interrupt request flags, INT0F~INT3F, are set, which will occur when a transition, whose type is chosen by the edge select bits, appears on the external interrupt pins. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, and respective external interrupt enable bit, INT0E~INT3E, must first be set. Additionally the correct interrupt edge type must be selected using the INTEG register to enable the external interrupt function and to choose the trigger edge type. As the external interrupt pins are pin-shared with I/O pins, they can only be configured as external interrupt pins if their external interrupt enable bit in the corresponding interrupt register has been set and the external interrupt pin is selected by the corresponding pin-shared function selection bits. The pin must also be setup as an input by setting the corresponding bit in the port control register. When the interrupt is enabled, the stack is not full and the correct transition type appears on the external interrupt pin, a subroutine call to the external interrupt vector, will take place. When the interrupt is serviced, the external interrupt request flags, INT0F~INT3F, will be automatically reset and the EMI bit will be automatically cleared to disable other interrupts. Note that any pull-high resistor selections on the external interrupt pins will remain valid even if the pin is used as an external interrupt input. The INTEG register is used to select the type of active edge that will trigger the external interrupt. A choice of either rising or falling or both edge types can be chosen to trigger an external interrupt. Note that the INTEG register can also be used to disable the external interrupt function. Multi-function Interrupt Within the device there are up to ten Multi-function interrupts. Unlike the other independent interrupts, these interrupts have no independent source, but rather are formed from other existing interrupt sources, namely the TM interrupts, LVD interrupt, EEPROM write operation interrupt, SIM interface interrupt, SPIA interface interrupt, UART interface interrupts, Comparator interrupts and Time Base interrupts. A Multi-function interrupt request will take place when any of the Multi-function interrupt request flags MFnF are set. The Multi-function interrupt flags will be set when any of their included functions generate an interrupt request flag. To allow the program to branch to its respective interrupt vector address, when the Multi-function interrupt is enabled and the stack is not full, and either one of the interrupts contained within each of Multi-function interrupt occurs, a subroutine call to one of the Multi-function interrupt vectors will take place. When the interrupt is serviced, the related Multi-Function request flag will be automatically reset and the EMI bit will be automatically cleared to disable other interrupts. However, it must be noted that, although the Multi-function Interrupt request flags will be automatically reset when the interrupt is serviced, the request flags from the original source of the Multi-function interrupts will not be automatically reset and must be manually reset by the application program. A/D Converter Interrupt The A/D Converter Interrupt is controlled by the termination of an A/D conversion process. An A/D Converter Interrupt request will take place when the A/D Converter Interrupt request flag, ADF, is set, which occurs when the A/D conversion process finishes. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, and A/D Interrupt enable bit, ADE, must first be set. When the interrupt is enabled, the stack is not full and the A/D conversion process has ended, a subroutine call to the A/D Converter Interrupt vector, will take place. When the interrupt is serviced, the A/D Converter Interrupt flag, ADF, will be automatically cleared. The EMI bit will also be automatically cleared to disable other interrupts. Rev. 1.00 259 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM TM Interrupt The Standard and Periodic TMs have two interrupts, one comes from the comparator A match situation and the other comes from the comparator P match situation. All of the TM interrupts are contained within the Multi-function Interrupts. For all of the TM types there are two interrupt request flags and two enable control bits. A TM interrupt request will take place when any of the TM request flags are set, a situation which occurs when a TM comparator P or A match situation happens. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, respective TM Interrupt enable bit, and relevant Multi-function Interrupt enable bit, MFnE, must first be set. When the interrupt is enabled, the stack is not full and a TM comparator match situation occurs, a subroutine call to the relevant Multi-function Interrupt vector locations, will take place. When the TM interrupt is serviced, the EMI bit will be automatically cleared to disable other interrupts. However, only the related MFnF flag will be automatically cleared. As the TM interrupt request flags will not be automatically cleared, they have to be cleared by the application program. LVD Interrupt The Low Voltage Detector Interrupt is contained within the Multi-function Interrupt. An LVD Interrupt request will take place when the LVD Interrupt request flag, LVF, is set, which occurs when the Low Voltage Detector function detects a low power supply voltage. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, Low Voltage Interrupt enable bit, LVE, and associated Multi-function interrupt enable bit, must first be set. When the interrupt is enabled, the stack is not full and a low voltage condition occurs, a subroutine call to the Multi-function Interrupt vector, will take place. When the Low Voltage Interrupt is serviced, the EMI bit will be automatically cleared to disable other interrupts. However, only the Multi-function interrupt request flag will be also automatically cleared. As the LVF flag will not be automatically cleared, it has to be cleared by the application program. EEPROM Interrupt The EEPROM Write Interrupt is contained within the Multi-function Interrupt. An EEPROM Write Interrupt request will take place when the EEPROM Write Interrupt request flag, DEF, is set, which occurs when an EEPROM Write cycle ends. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, EEPROM Write Interrupt enable bit, DEE, and associated Multi-function interrupt enable bit must first be set. When the interrupt is enabled, the stack is not full and an EEPROM Write cycle ends, a subroutine call to the respective Multi-function Interrupt vector will take place. When the EEPROM Write Interrupt is serviced, the EMI bit will be automatically cleared to disable other interrupts. However, only the Multi-function interrupt request flag will be automatically cleared. As the DEF flag will not be automatically cleared, it has to be cleared by the application program. Serial Interface Module Interrupt The Serial Interface Module Interrupt, also known as the SIM interrupt, is contained within the Multi-function Interrupt. A SIM Interrupt request will take place when the SIM Interrupt request flag, SIMF, is set, which occurs when a byte of data has been received or transmitted by the SIM interface, an I2C slave address match or I2C bus time-out occurrence. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, the Serial Interface Interrupt enable bit, SIME, and Multi-function interrupt enable bit must first be set. When the interrupt is enabled, the stack is not full and any of the above described situations occurs, a subroutine call to the respective Multi-function Interrupt vector, will take place. When the Serial Interface Interrupt is serviced, the EMI bit will be automatically cleared to disable other interrupts, however only the Multi-function interrupt request flag will be also automatically cleared. As the SIMF flag will not be automatically cleared, it has to be cleared by the application program. Rev. 1.00 260 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SPIA Interface Interrupt The SPIA Interface Module Interrupt is contained within the Multi-function Interrupt. A SPIA Interrupt request will take place when the SPIA Interrupt request flag, SPIAF, is set, which occurs when a byte of data has been received or transmitted by the SPIA interface. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, the Serial Interface Interrupt enable bit, SPIAE, and Multi-function interrupt enable bit must first be set. When the interrupt is enabled, the stack is not full and a byte of data has been transmitted or received by the SPIA interface, a subroutine call to the respective Multi-function Interrupt vector, will take place. When the SPIA Interface Interrupt is serviced, the EMI bit will be automatically cleared to disable other interrupts. However, only the Multi-function interrupt request flag will be automatically cleared. As the SPIAF flag will not be automatically cleared, it has to be cleared by the application program. UART Transfer Interrupt The UART Transfer Interrupt is contained within the Multi-function interrupt and controlled by several UARTn transfer conditions. When one of these conditions occurs, an interrupt pulse will be generated to get the attention of the microcontroller. These conditions are a transmitter data register empty, transmitter idle, receiver data available, receiver overrun, address detect and an RXn pin wake-up. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, UART Interrupt enable bit, URnE, and Multi-function interrupt enable bit must first be set. When the interrupt is enabled, the stack is not full and any of the conditions described above occurs, a subroutine call to the corresponding Multi-function Interrupt vector, will take place. When the UARTn interrupt is serviced, the EMI bit will be automatically cleared to disable other interrupts. However, only the Multi-function interrupt request flag will be automatically cleared. As the UARTn Interrupt flag, URnF, will not be automatically cleared, it has to be cleared by the application program. Comparator Interrupt The comparator interrupt is contained within the Multi-function interrupt and controlled by the relevant internal comparators. A comparator interrupt request will take place when the comparator interrupt request flags, CP0F or CP1F, are set, which occurs when the comparator output bit changes state. To allow the program to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, comparator interrupt enable bit, CP0E or CP1E, and Multi-function interrupt enable bit must first be set. When the interrupt is enabled, the stack is not full and the comparator inputs generate a comparator output transition, a subroutine call to the Multi-function interrupt cector, will take place. When the Comparator interrupt is serviced, the EMI bit will be automatically cleared to disable other interrupts. Also the corresponding Multi-function interrupt request flag will be automatically reset. As the CPnF flag will not be automatically cleared, it has to be cleared by the application program. Rev. 1.00 261 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Time Base Interrupt The function of the Time Base Interrupt is to provide regular time signal in the form of an internal interrupt. It is contained within the Multi-function interrupt and controlled by the overflow signal from its internal timer. When this happens its interrupt request flag, TBnF, will be set. To allow the program to branch to its respective interrupt vector addresses, the global interrupt enable bit, EMI, Time Base enable bit, TBnE, and Multi-function interrupt enable bit must first be set. When the interrupt is enabled, the stack is not full and the Time Base overflows, a subroutine call to its respective Multi-function interrupt vector location will take place. When the interrupt is serviced, the EMI bit will automatically be cleared to disable other interrupts. Also the corresponding Multifunction interrupt request flag will be automatically reset. As the interrupt request flag, TBnF, will not be automatically reset, it has to be cleared by the application program. The purpose of the Time Base Interrupt is to provide an interrupt signal at fixed time periods. Its clock source, fPSC0 or fPSC1, originates from the internal clock source fSYS, fSYS/4 or fSUB and then passes through a divider, the division ratio of which is selected by programming the appropriate bits in the TB0C and TB1C registers to obtain longer interrupt periods whose value ranges. The clock source which in turn controls the Time Base interrupt period is selected using the CLKSEL0[1:0] and CLKSEL1[1:0] bits in the PSC0R and PSC1R register respectively. fSYS fSYS/4 fSUB M U X fPSC0 Prescaler 0 TB0ON fPSC0/28 ~ fPSC0/215 M U X TB0[2:0] CLKSEL0[1:0] fSYS fSYS/4 fSUB M U X fPSC1 Time Base 0 Interrupt Prescaler 1 fPSC1/28 ~ fPSC1/215 M U X TB1ON CLKSEL1[1:0] Time Base 1 Interrupt TB1[2:0] Time Base Interrupts PSC0R Register Rev. 1.00 Bit 7 6 5 4 3 2 Name — — — — — — 1 R/W — — — — — — R/W R/W POR — — — — — — 0 0 Bit 7~2 Unimplemented, read as "0" Bit 1~0 CLKSEL01~CLKSEL00: Prescaler 0 clock source fPSC0 selection 00: fSYS 01: fSYS/4 1x: fSUB 262 0 CLKSEL01 CLKSEL00 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM PSC1R Register Bit 7 6 5 4 3 2 Name — — — — — — 1 0 CLKSEL11 CLKSEL10 R/W — — — — — — R/W R/W POR — — — — — — 0 0 Bit 7~2 Unimplemented, read as "0" Bit 1~0 CLKSEL11~CLKSEL10: Prescaler 1 clock source fPSC1 selection 00: fSYS 01: fSYS/4 1x: fSUB TB0C Register Bit 7 6 5 4 3 2 1 0 Name TB0ON — — — — TB02 TB01 TB00 R/W R/W — — — — R/W R/W R/W POR 0 — — — — 0 0 0 Bit 7 TB0ON: Time Base 0 Enable Control 0: Disable 1: Enable Bit 6~3 Unimplemented, read as "0" Bit 2~0 TB02~TB00: Time Base 0 time-out period selection 000: 28/fPSC0 001: 29/fPSC0 010: 210/fPSC0 011: 211/fPSC0 100: 212/fPSC0 101: 213/fPSC0 110: 214/fPSC0 111: 215/fPSC0 TB1C Register Rev. 1.00 Bit 7 6 5 4 3 2 1 0 Name TB1ON — — — — TB12 TB11 TB10 R/W R/W — — — — R/W R/W R/W POR 0 — — — — 0 0 0 Bit 7 TB1ON: Time Base 1 Enable Control 0: Disable 1: Enable Bit 6~3 Unimplemented, read as "0" Bit 2~0 TB12~TB10: Time Base 1 time-out period selection 000: 28/fPSC1 001: 29/fPSC1 010: 210/fPSC1 011: 211/fPSC1 100: 212/fPSC1 101: 213/fPSC1 110: 214/fPSC1 111: 215/fPSC1 263 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Interrupt Wake-up Function Each of the interrupt functions has the capability of waking up the microcontroller when in the SLEEP or IDLE Mode. A wake-up is generated when an interrupt request flag changes from low to high and is independent of whether the interrupt is enabled or not. Therefore, even though these devices are in the SLEEP or IDLE Mode and its system oscillator stopped, situations such as external edge transitions on the external interrupt pins, a low power supply voltage or comparator input change may cause their respective interrupt flag to be set high and consequently generate an interrupt. Care must therefore be taken if spurious wake-up situations are to be avoided. If an interrupt wake-up function is to be disabled then the corresponding interrupt request flag should be set high before the device enters the SLEEP or IDLE Mode. The interrupt enable bits have no effect on the interrupt wake-up function. Programming Considerations By disabling the relevant interrupt enable bits, a requested interrupt can be prevented from being serviced, however, once an interrupt request flag is set, it will remain in this condition in the interrupt register until the corresponding interrupt is serviced or until the request flag is cleared by the application program. Where a certain interrupt is contained within a Multi-function interrupt, then when the interrupt service routine is executed, as only the Multi-function interrupt request flags, MFnF, will be automatically cleared, the individual request flag for the function needs to be cleared by the application program. It is recommended that programs do not use the "CALL" instruction within the interrupt service subroutine. Interrupts often occur in an unpredictable manner or need to be serviced immediately. If only one stack is left and the interrupt is not well controlled, the original control sequence will be damaged once a CALL subroutine is executed in the interrupt subroutine. Every interrupt has the capability of waking up the microcontroller when it is in the SLEEP or IDLE Mode, the wake up being generated when the interrupt request flag changes from low to high. If it is required to prevent a certain interrupt from waking up the microcontroller then its respective request flag should be first set high before enter SLEEP or IDLE Mode. As only the Program Counter is pushed onto the stack, then when the interrupt is serviced, if the contents of the accumulator, status register or other registers are altered by the interrupt service program, their contents should be saved to the memory at the beginning of the interrupt service routine. To return from an interrupt subroutine, either a RET or RETI instruction may be executed. The RETI instruction in addition to executing a return to the main program also automatically sets the EMI bit high to allow further interrupts. The RET instruction however only executes a return to the main program leaving the EMI bit in its present zero state and therefore disabling the execution of further interrupts. Rev. 1.00 264 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Application Circuits PLCD VDD VMAX VDD COM0~COM3 RES SEG0/COM4 ~SEG3/COM7 SEG4~SEG55 100KΩ 0.1μF LCD Panel V1 0.1μF V2 C1 VSS 0.1μF 0.1μF 0.1μF C2 PA0~PA7 PB0~PB7 OSC Circuit OSC Circuit OSC1 PC0~PC7 PD0~PD6 OSC2 PE0~PE7 XT1 PF0~PF7 PG0~PG7 XT2 PH0~PH7 PJ0~PJ7 Rev. 1.00 265 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Instruction Set Introduction Central to the successful operation of any microcontroller is its instruction set, which is a set of program instruction codes that directs the microcontroller to perform certain operations. In the case of Holtek microcontroller, a comprehensive and flexible set of over 60 instructions is provided to enable programmers to implement their application with the minimum of programming overheads. For easier understanding of the various instruction codes, they have been subdivided into several functional groupings. Instruction Timing Most instructions are implemented within one instruction cycle. The exceptions to this are branch, call, or table read instructions where two instruction cycles are required. One instruction cycle is equal to 4 system clock cycles, therefore in the case of an 8MHz system oscillator, most instructions would be implemented within 0.5μs and branch or call instructions would be implemented within 1μs. Although instructions which require one more cycle to implement are generally limited to the JMP, CALL, RET, RETI and table read instructions, it is important to realize that any other instructions which involve manipulation of the Program Counter Low register or PCL will also take one more cycle to implement. As instructions which change the contents of the PCL will imply a direct jump to that new address, one more cycle will be required. Examples of such instructions would be "CLR PCL" or "MOV PCL, A". For the case of skip instructions, it must be noted that if the result of the comparison involves a skip operation then this will also take one more cycle, if no skip is involved then only one cycle is required. Moving and Transferring Data The transfer of data within the microcontroller program is one of the most frequently used operations. Making use of three kinds of MOV instructions, data can be transferred from registers to the Accumulator and vice-versa as well as being able to move specific immediate data directly into the Accumulator. One of the most important data transfer applications is to receive data from the input ports and transfer data to the output ports. Arithmetic Operations The ability to perform certain arithmetic operations and data manipulation is a necessary feature of most microcontroller applications. Within the Holtek microcontroller instruction set are a range of add and subtract instruction mnemonics to enable the necessary arithmetic to be carried out. Care must be taken to ensure correct handling of carry and borrow data when results exceed 255 for addition and less than 0 for subtraction. The increment and decrement instructions INC, INCA, DEC and DECA provide a simple means of increasing or decreasing by a value of one of the values in the destination specified. Rev. 1.00 266 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Logical and Rotate Operation The standard logical operations such as AND, OR, XOR and CPL all have their own instruction within the Holtek microcontroller instruction set. As with the case of most instructions involving data manipulation, data must pass through the Accumulator which may involve additional programming steps. In all logical data operations, the zero flag may be set if the result of the operation is zero. Another form of logical data manipulation comes from the rotate instructions such as RR, RL, RRC and RLC which provide a simple means of rotating one Bit right or left. Different rotate instructions exist depending on program requirements. Rotate instructions are useful for serial port programming applications where data can be rotated from an internal register into the Carry Bit from where it can be examined and the necessary serial Bit set high or low. Another application which rotate data operations are used is to implement multiplication and division calculations. Branches and Control Transfer Program branching takes the form of either jumps to specified locations using the JMP instruction or to a subroutine using the CALL instruction. They differ in the sense that in the case of a subroutine call, the program must return to the instruction immediately when the subroutine has been carried out. This is done by placing a return instruction "RET" in the subroutine which will cause the program to jump back to the address right after the CALL instruction. In the case of a JMP instruction, the program simply jumps to the desired location. There is no requirement to jump back to the original jumping off point as in the case of the CALL instruction. One special and extremely useful set of branch instructions are the conditional branches. Here a decision is first made regarding the condition of a certain data memory or individual Bits. Depending upon the conditions, the program will continue with the next instruction or skip over it and jump to the following instruction. These instructions are the key to decision making and branching within the program perhaps determined by the condition of certain input switches or by the condition of internal data Bits. Bit Operations The ability to provide single Bit operations on Data Memory is an extremely flexible feature of all Holtek microcontrollers. This feature is especially useful for output port Bit programming where individual Bits or port pins can be directly set high or low using either the "SET [m].i" or "CLR [m]. i" instructions respectively. The feature removes the need for programmers to first read the 8-Bit output port, manipulate the input data to ensure that other Bits are not changed and then output the port with the correct new data. This read-modify-write process is taken care of automatically when these Bit operation instructions are used. Table Read Operations Data storage is normally implemented by using registers. However, when working with large amounts of fixed data, the volume involved often makes it inconvenient to store the fixed data in the Data Memory. To overcome this problem, Holtek microcontrollers allow an area of Program Memory to be set as a table where data can be directly stored. A set of easy to use instructions provides the means by which this fixed data can be referenced and retrieved from the Program Memory. Other Operations In addition to the above functional instructions, a range of other instructions also exist such as the "HALT" instruction for Power-down operations and instructions to control the operation of the Watchdog Timer for reliable program operations under extreme electric or electromagnetic environments. For their relevant operations, refer to the functional related sections. Rev. 1.00 267 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Instruction Set Summary The instructions related to the data memory access in the following table can be used when the desired data memory is located in Data Memory sector 0. Table Conventions x: Bits immediate data m: Data Memory address A: Accumulator i: 0~7 number of bits addr: Program memory address Mnemonic Description Cycles Flag Affected 1 1Note 1 1 1Note 1 1 1Note 1 1 1Note 1Note Z, C, AC, OV, SC Z, C, AC, OV, SC Z, C, AC, OV, SC Z, C, AC, OV, SC Z, C, AC, OV, SC Z, C, AC, OV, SC, CZ Z, C, AC, OV, SC, CZ Z, C, AC, OV, SC, CZ Z, C, AC, OV, SC, CZ Z, C, AC, OV, SC, CZ Z, C, AC, OV, SC, CZ C 1 1 1 1Note 1Note 1Note 1 1 1 1Note 1 Z Z Z Z Z Z Z Z Z Z Z Increment Data Memory with result in ACC Increment Data Memory Decrement Data Memory with result in ACC Decrement Data Memory 1 1Note 1 1Note Z Z Z Z Rotate Data Memory right with result in ACC Rotate Data Memory right Rotate Data Memory right through Carry with result in ACC Rotate Data Memory right through Carry Rotate Data Memory left with result in ACC Rotate Data Memory left Rotate Data Memory left through Carry with result in ACC Rotate Data Memory left through Carry 1 1Note 1 1Note 1 1Note 1 1Note None None C C None None C C Arithmetic Add Data Memory to ACC ADD A,[m] ADDM A,[m] Add ACC to Data Memory ADD A,x Add immediate data to ACC ADC A,[m] Add Data Memory to ACC with Carry ADCM A,[m] Add ACC to Data memory with Carry SUB A,x Subtract immediate data from the ACC SUB A,[m] Subtract Data Memory from ACC SUBM A,[m] Subtract Data Memory from ACC with result in Data Memory SBC A,x Subtract immediate data from ACC with Carry SBC A,[m] Subtract Data Memory from ACC with Carry SBCM A,[m] Subtract Data Memory from ACC with Carry, result in Data Memory DAA [m] Decimal adjust ACC for Addition with result in Data Memory Logic Operation AND A,[m] Logical AND Data Memory to ACC OR A,[m] Logical OR Data Memory to ACC XOR A,[m] Logical XOR Data Memory to ACC ANDM A,[m] Logical AND ACC to Data Memory ORM A,[m] Logical OR ACC to Data Memory XORM A,[m] Logical XOR ACC to Data Memory AND A,x Logical AND immediate Data to ACC OR A,x Logical OR immediate Data to ACC XOR A,x Logical XOR immediate Data to ACC CPL [m] Complement Data Memory CPLA [m] Complement Data Memory with result in ACC Increment & Decrement INCA [m] INC [m] DECA [m] DEC [m] Rotate RRA [m] RR [m] RRCA [m] RRC [m] RLA [m] RL [m] RLCA [m] RLC [m] Rev. 1.00 268 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Mnemonic Description Cycles Flag Affected Data Move MOV A,[m] MOV [m],A MOV A,x Move Data Memory to ACC Move ACC to Data Memory Move immediate data to ACC 1 1Note 1 None None None Clear bit of Data Memory Set bit of Data Memory 1Note 1Note None None 2 1Note 1Note 1Note 1Note 1Note 1Note 1Note 1Note 1Note 2 2 2 2 None None None None None None None None None None None None None None 2Note 2Note 2Note None None None 2Note None 1 1Note 1Note 1 1Note 1 1 None None None TO, PDF None None TO, PDF Bit Operation CLR [m].i SET [m].i Branch Operation JMP addr SZ [m] SZA [m] SZ [m].i SNZ [m] SNZ [m].i SIZ [m] SDZ [m] SIZA [m] SDZA [m] CALL addr RET RET A,x RETI Jump unconditionally Skip if Data Memory is zero Skip if Data Memory is zero with data movement to ACC Skip if bit i of Data Memory is zero Skip if Data Memory is not zero Skip if bit i of Data Memory is not zero Skip if increment Data Memory is zero Skip if decrement Data Memory is zero Skip if increment Data Memory is zero with result in ACC Skip if decrement Data Memory is zero with result in ACC Subroutine call Return from subroutine Return from subroutine and load immediate data to ACC Return from interrupt Table Read Operation TABRD [m] Read table (specific page) to TBLH and Data Memory TABRDL [m] Read table (last page) to TBLH and Data Memory ITABRD [m] Increment table pointer TBLP first and Read table to TBLH and Data Memory Increment table pointer TBLP first and Read table (last page) to TBLH and ITABRDL [m] Data Memory Miscellaneous NOP CLR [m] SET [m] CLR WDT SWAP [m] SWAPA [m] HALT No operation Clear Data Memory Set Data Memory Clear Watchdog Timer Swap nibbles of Data Memory Swap nibbles of Data Memory with result in ACC Enter power down mode Note: 1. For skip instructions, if the result of the comparison involves a skip then up to three cycles are required, if no skip takes place only one cycle is required. 2. Any instruction which changes the contents of the PCL will also require 2 cycles for execution. 3. For the "CLR WDT" instruction the TO and PDF flags may be affected by the execution status. The TO and PDF flags are cleared after the "CLR WDT" instructions is executed. Otherwise the TO and PDF flags remain unchanged. Rev. 1.00 269 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Extended Instruction Set The extended instructions are used to support the full range address access for the data memory. When the accessed data memory is located in any data memory sections except sector 0, the extended instruction can be used to access the data memory instead of using the indirect addressing access to improve the CPU firmware performance. Mnemonic Description Cycles Flag Affected 2 2Note 2 2Note 2 2Note 2 2Note 2Note Z, C, AC, OV, SC Z, C, AC, OV, SC Z, C, AC, OV, SC Z, C, AC, OV, SC Z, C, AC, OV, SC, CZ Z, C, AC, OV, SC, CZ Z, C, AC, OV, SC, CZ Z, C, AC, OV, SC, CZ C 2 2 2 2Note 2Note 2Note 2Note 2 Z Z Z Z Z Z Z Z Increment Data Memory with result in ACC Increment Data Memory Decrement Data Memory with result in ACC Decrement Data Memory 2 2Note 2 2Note Z Z Z Z Rotate Data Memory right with result in ACC Rotate Data Memory right Rotate Data Memory right through Carry with result in ACC Rotate Data Memory right through Carry Rotate Data Memory left with result in ACC Rotate Data Memory left Rotate Data Memory left through Carry with result in ACC Rotate Data Memory left through Carry 2 2Note 2 2Note 2 2Note 2 2Note None None C C None None C C Move Data Memory to ACC Move ACC to Data Memory 2 2Note None None Clear bit of Data Memory Set bit of Data Memory 2Note 2Note None None Arithmetic Add Data Memory to ACC LADD A,[m] LADDM A,[m] Add ACC to Data Memory LADC A,[m] Add Data Memory to ACC with Carry LADCM A,[m] Add ACC to Data memory with Carry LSUB A,[m] Subtract Data Memory from ACC LSUBM A,[m] Subtract Data Memory from ACC with result in Data Memory LSBC A,[m] Subtract Data Memory from ACC with Carry LSBCM A,[m] Subtract Data Memory from ACC with Carry, result in Data Memory LDAA [m] Decimal adjust ACC for Addition with result in Data Memory Logic Operation LAND A,[m] Logical AND Data Memory to ACC LOR A,[m] Logical OR Data Memory to ACC LXOR A,[m] Logical XOR Data Memory to ACC LANDM A,[m] Logical AND ACC to Data Memory LORM A,[m] Logical OR ACC to Data Memory LXORM A,[m] Logical XOR ACC to Data Memory LCPL [m] Complement Data Memory LCPLA [m] Complement Data Memory with result in ACC Increment & Decrement LINCA [m] LINC [m] LDECA [m] LDEC [m] Rotate LRRA [m] LRR [m] LRRCA [m] LRRC [m] LRLA [m] LRL [m] LRLCA [m] LRLC [m] Data Move LMOV A,[m] LMOV [m],A Bit Operation LCLR [m].i LSET [m].i Rev. 1.00 270 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Mnemonic Description Cycles Flag Affected Branch LSZ [m] LSZA [m] LSNZ [m] LSZ [m].i LSNZ [m].i LSIZ [m] LSDZ [m] LSIZA [m] LSDZA [m] Skip if Data Memory is zero Skip if Data Memory is zero with data movement to ACC Skip if Data Memory is not zero Skip if bit i of Data Memory is zero Skip if bit i of Data Memory is not zero Skip if increment Data Memory is zero Skip if decrement Data Memory is zero Skip if increment Data Memory is zero with result in ACC Skip if decrement Data Memory is zero with result in ACC 2Note 2Note 2Note 2Note 2Note 2Note 2Note 2Note 2Note None None None None None None None None None 3Note 3Note 3Note None None None 3Note None 2Note 2Note 2Note 2 None None None None Table Read LTABRD [m] Read table to TBLH and Data Memory LTABRDL [m] Read table (last page) to TBLH and Data Memory LITABRD [m] Increment table pointer TBLP first and Read table to TBLH and Data Memory Increment table pointer TBLP first and Read table (last page) to TBLH and LITABRDL [m] Data Memory Miscellaneous LCLR [m] LSET [m] LSWAP [m] LSWAPA [m] Clear Data Memory Set Data Memory Swap nibbles of Data Memory Swap nibbles of Data Memory with result in ACC Note: 1. For these extended skip instructions, if the result of the comparison involves a skip then up to four cycles are required, if no skip takes place two cycles is required. 2. Any extended instruction which changes the contents of the PCL register will also require three cycles for execution. Rev. 1.00 271 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Instruction Definition ADC A,[m] Description Operation Affected flag(s) ADCM A,[m] Description Operation Affected flag(s) ADD A,[m] Description Add Data Memory to ACC with Carry The contents of the specified Data Memory, Accumulator and the carry flag are added. The result is stored in the Accumulator. ACC ← ACC + [m] + C OV, Z, AC, C, SC Add ACC to Data Memory with Carry The contents of the specified Data Memory, Accumulator and the carry flag are added. The result is stored in the specified Data Memory. [m] ← ACC + [m] + C OV, Z, AC, C, SC Add Data Memory to ACC The contents of the specified Data Memory and the Accumulator are added. The result is stored in the Accumulator. Operation Affected flag(s) ACC ← ACC + [m] OV, Z, AC, C, SC ADD A,x Description Add immediate data to ACC The contents of the Accumulator and the specified immediate data are added. The result is stored in the Accumulator. ACC ← ACC + x OV, Z, AC, C, SC Operation Affected flag(s) ADDM A,[m] Description Operation Affected flag(s) AND A,[m] Description Operation Affected flag(s) AND A,x Description Operation Affected flag(s) ANDM A,[m] Description Operation Affected flag(s) Rev. 1.00 Add ACC to Data Memory The contents of the specified Data Memory and the Accumulator are added. The result is stored in the specified Data Memory. [m] ← ACC + [m] OV, Z, AC, C, SC Logical AND Data Memory to ACC Data in the Accumulator and the specified Data Memory perform a bitwise logical AND operation. The result is stored in the Accumulator. ACC ← ACC ″AND″ [m] Z Logical AND immediate data to ACC Data in the Accumulator and the specified immediate data perform a bit wise logical AND operation. The result is stored in the Accumulator. ACC ← ACC ″AND″ x Z Logical AND ACC to Data Memory Data in the specified Data Memory and the Accumulator perform a bitwise logical AND operation. The result is stored in the Data Memory. [m] ← ACC ″AND″ [m] Z 272 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Affected flag(s) Subroutine call Unconditionally calls a subroutine at the specified address. The Program Counter then increments by 1 to obtain the address of the next instruction which is then pushed onto the stack. The specified address is then loaded and the program continues execution from this new address. As this instruction requires an additional operation, it is a two cycle instruction. Stack ← Program Counter + 1 Program Counter ← addr None CLR [m] Description Operation Affected flag(s) Clear Data Memory Each bit of the specified Data Memory is cleared to 0. [m] ← 00H None CLR [m].i Description Operation Affected flag(s) Clear bit of Data Memory Bit i of the specified Data Memory is cleared to 0. [m].i ← 0 None CLR WDT Description Operation Clear Watchdog Timer The TO, PDF flags and the WDT are all cleared. WDT cleared TO ← 0 PDF ← 0 TO, PDF CALL addr Description Operation Affected flag(s) CPL [m] Description Operation Affected flag(s) CPLA [m] Description Operation Affected flag(s) DAA [m] Description Operation Affected flag(s) Rev. 1.00 Complement Data Memory Each bit of the specified Data Memory is logically complemented (1′s complement). Bits which previously contained a 1 are changed to 0 and vice versa. [m] ← [m] Z Complement Data Memory with result in ACC Each bit of the specified Data Memory is logically complemented (1′s complement). Bits which previously contained a 1 are changed to 0 and vice versa. The complemented result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC ← [m] Z Decimal-Adjust ACC for addition with result in Data Memory Convert the contents of the Accumulator value to a BCD (Binary Coded Decimal) value resulting from the previous addition of two BCD variables. If the low nibble is greater than 9 or if AC flag is set, then a value of 6 will be added to the low nibble. Otherwise the low nibble remains unchanged. If the high nibble is greater than 9 or if the C flag is set, then a value of 6 will be added to the high nibble. Essentially, the decimal conversion is performed by adding 00H, 06H, 60H or 66H depending on the Accumulator and flag conditions. Only the C flag may be affected by this instruction which indicates that if the original BCD sum is greater than 100, it allows multiple precision decimal addition. [m] ← ACC + 00H or [m] ← ACC + 06H or [m] ← ACC + 60H or [m] ← ACC + 66H C 273 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM DEC [m] Description Operation Affected flag(s) Decrement Data Memory Data in the specified Data Memory is decremented by 1. [m] ← [m] − 1 Z DECA [m] Description Decrement Data Memory with result in ACC Data in the specified Data Memory is decremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged. ACC ← [m] − 1 Z Operation Affected flag(s) Affected flag(s) Enter power down mode This instruction stops the program execution and turns off the system clock. The contents of the Data Memory and registers are retained. The WDT and prescaler are cleared. The power down flag PDF is set and the WDT time-out flag TO is cleared. TO ← 0 PDF ← 1 TO, PDF INC [m] Description Operation Affected flag(s) Increment Data Memory Data in the specified Data Memory is incremented by 1. [m] ← [m] + 1 Z INCA [m] Description Increment Data Memory with result in ACC Data in the specified Data Memory is incremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged. ACC ← [m] + 1 Z HALT Description Operation Operation Affected flag(s) Operation Affected flag(s) Jump unconditionally The contents of the Program Counter are replaced with the specified address. Program execution then continues from this new address. As this requires the insertion of a dummy instruction while the new address is loaded, it is a two cycle instruction. Program Counter ← addr None MOV A,[m] Description Operation Affected flag(s) Move Data Memory to ACC The contents of the specified Data Memory are copied to the Accumulator. ACC ← [m] None MOV A,x Description Operation Affected flag(s) Move immediate data to ACC The immediate data specified is loaded into the Accumulator. ACC ← x None MOV [m],A Description Operation Affected flag(s) Move ACC to Data Memory The contents of the Accumulator are copied to the specified Data Memory. [m] ← ACC None JMP addr Description Rev. 1.00 274 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM NOP Description Operation Affected flag(s) No operation No operation is performed. Execution continues with the next instruction. No operation None OR A,[m] Description Logical OR Data Memory to ACC Data in the Accumulator and the specified Data Memory perform a bitwise logical OR operation. The result is stored in the Accumulator. ACC ← ACC ″OR″ [m] Z Operation Affected flag(s) OR A,x Description Operation Affected flag(s) ORM A,[m] Description Operation Affected flag(s) RET Description Operation Affected flag(s) RET A,x Description Operation Affected flag(s) RETI Description Operation Affected flag(s) RL [m] Description Operation Affected flag(s) Rev. 1.00 Logical OR immediate data to ACC Data in the Accumulator and the specified immediate data perform a bitwise logical OR operation. The result is stored in the Accumulator. ACC ← ACC ″OR″ x Z Logical OR ACC to Data Memory Data in the specified Data Memory and the Accumulator perform a bitwise logical OR operation. The result is stored in the Data Memory. [m] ← ACC ″OR″ [m] Z Return from subroutine The Program Counter is restored from the stack. Program execution continues at the restored address. Program Counter ← Stack None Return from subroutine and load immediate data to ACC The Program Counter is restored from the stack and the Accumulator loaded with the specified immediate data. Program execution continues at the restored address. Program Counter ← Stack ACC ← x None Return from interrupt The Program Counter is restored from the stack and the interrupts are re-enabled by setting the EMI bit. EMI is the master interrupt global enable bit. If an interrupt was pending when the RETI instruction is executed, the pending Interrupt routine will be processed before returning to the main program. Program Counter ← Stack EMI ← 1 None Rotate Data Memory left The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit 0. [m].(i+1) ← [m].i; (i=0~6) [m].0 ← [m].7 None 275 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM RLA [m] Description Operation Affected flag(s) RLC [m] Description Operation Affected flag(s) RLCA [m] Description Operation Affected flag(s) RR [m] Description Operation Affected flag(s) RRA [m] Description Operation Affected flag(s) RRC [m] Description Operation Affected flag(s) Rev. 1.00 Rotate Data Memory left with result in ACC The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit 0. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC.(i+1) ← [m].i; (i=0~6) ACC.0 ← [m].7 None Rotate Data Memory left through Carry The contents of the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces the Carry bit and the original carry flag is rotated into bit 0. [m].(i+1) ← [m].i; (i=0~6) [m].0 ← C C ← [m].7 C Rotate Data Memory left through Carry with result in ACC Data in the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces the Carry bit and the original carry flag is rotated into the bit 0. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC.(i+1) ← [m].i; (i=0~6) ACC.0 ← C C ← [m].7 C Rotate Data Memory right The contents of the specified Data Memory are rotated right by 1 bit with bit 0 rotated into bit 7. [m].i ← [m].(i+1); (i=0~6) [m].7 ← [m].0 None Rotate Data Memory right with result in ACC Data in the specified Data Memory is rotated right by 1 bit with bit 0 rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC.i ← [m].(i+1); (i=0~6) ACC.7 ← [m].0 None Rotate Data Memory right through Carry The contents of the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces the Carry bit and the original carry flag is rotated into bit 7. [m].i ← [m].(i+1); (i=0~6) [m].7 ← C C ← [m].0 C 276 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM RRCA [m] Description Operation Affected flag(s) SBC A,[m] Description Operation Affected flag(s) SBC A, x Description Operation Affected flag(s) SBCM A,[m] Description Operation Affected flag(s) SDZ [m] Description Operation Affected flag(s) SDZA [m] Description Operation Affected flag(s) Rev. 1.00 Rotate Data Memory right through Carry with result in ACC Data in the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces the Carry bit and the original carry flag is rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC.i ← [m].(i+1); (i=0~6) ACC.7 ← C C ← [m].0 C Subtract Data Memory from ACC with Carry The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. ACC ← ACC − [m] − C OV, Z, AC, C, SC, CZ Subtract immediate data from ACC with Carry The immediate data and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. ACC ← ACC - [m] - C OV, Z, AC, C, SC, CZ Subtract Data Memory from ACC with Carry and result in Data Memory The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. [m] ← ACC − [m] − C OV, Z, AC, C, SC, CZ Skip if decrement Data Memory is 0 The contents of the specified Data Memory are first decremented by 1. If the result is 0 the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. [m] ← [m] − 1 Skip if [m]=0 None Skip if decrement Data Memory is zero with result in ACC The contents of the specified Data Memory are first decremented by 1. If the result is 0, the following instruction is skipped. The result is stored in the Accumulator but the specified Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0, the program proceeds with the following instruction. ACC ← [m] − 1 Skip if ACC=0 None 277 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SET [m] Description Operation Affected flag(s) Set Data Memory Each bit of the specified Data Memory is set to 1. [m] ← FFH None SET [m].i Description Operation Affected flag(s) Set bit of Data Memory Bit i of the specified Data Memory is set to 1. [m].i ← 1 None SIZ [m] Description Skip if increment Data Memory is 0 The contents of the specified Data Memory are first incremented by 1. If the result is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. [m] ← [m] + 1 Skip if [m]=0 None Operation Affected flag(s) SIZA [m] Description Operation Affected flag(s) SNZ [m].i Description Operation Affected flag(s) SNZ [m] Description Operation Affected flag(s) SUB A,[m] Description Operation Affected flag(s) Rev. 1.00 Skip if increment Data Memory is zero with result in ACC The contents of the specified Data Memory are first incremented by 1. If the result is 0, the following instruction is skipped. The result is stored in the Accumulator but the specified Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. ACC ← [m] + 1 Skip if ACC=0 None Skip if Data Memory is not 0 If the specified Data Memory is not 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is 0 the program proceeds with the following instruction. Skip if [m].i ≠ 0 None Skip if Data Memory is not 0 If the specified Data Memory is not 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is 0 the program proceeds with the following instruction. Skip if [m]≠ 0 None Subtract Data Memory from ACC The specified Data Memory is subtracted from the contents of the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. ACC ← ACC − [m] OV, Z, AC, C, SC, CZ 278 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM SUBM A,[m] Description Operation Affected flag(s) Subtract Data Memory from ACC with result in Data Memory The specified Data Memory is subtracted from the contents of the Accumulator. The result is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. [m] ← ACC − [m] OV, Z, AC, C, SC, CZ Operation Affected flag(s) Subtract immediate data from ACC The immediate data specified by the code is subtracted from the contents of the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. ACC ← ACC − x OV, Z, AC, C, SC, CZ SWAP [m] Description Operation Affected flag(s) Swap nibbles of Data Memory The low-order and high-order nibbles of the specified Data Memory are interchanged. [m].3~[m].0 ↔ [m].7~[m].4 None SWAPA [m] Description Swap nibbles of Data Memory with result in ACC The low-order and high-order nibbles of the specified Data Memory are interchanged. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged. ACC.3~ACC.0 ← [m].7~[m].4 ACC.7~ACC.4 ← [m].3~[m].0 None SUB A,x Description Operation Affected flag(s) SZ [m] Description Operation Affected flag(s) SZA [m] Description Operation Affected flag(s) SZ [m].i Description Operation Affected flag(s) Rev. 1.00 Skip if Data Memory is 0 If the contents of the specified Data Memory is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. Skip if [m]=0 None Skip if Data Memory is 0 with data movement to ACC The contents of the specified Data Memory are copied to the Accumulator. If the value is zero, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. ACC ← [m] Skip if [m]=0 None Skip if bit i of Data Memory is 0 If bit i of the specified Data Memory is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0, the program proceeds with the following instruction. Skip if [m].i=0 None 279 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM TABRD [m] Description Operation Affected flag(s) TABRDL [m] Description Operation Affected flag(s) ITABRD [m] Description Operation Affected flag(s) ITABRDL [m] Description Operation Affected flag(s) XOR A,[m] Description Operation Affected flag(s) XORM A,[m] Description Operation Affected flag(s) XOR A,x Description Operation Affected flag(s) Rev. 1.00 Read table (specific page) to TBLH and Data Memory The low byte of the program code (specific page) addressed by the table pointer pair (TBLP and TBHP) is moved to the specified Data Memory and the high byte moved to TBLH. [m] ← program code (low byte) TBLH ← program code (high byte) None Read table (last page) to TBLH and Data Memory The low byte of the program code (last page) addressed by the table pointer (TBLP) is moved to the specified Data Memory and the high byte moved to TBLH. [m] ← program code (low byte) TBLH ← program code (high byte) None Increment table pointer low byte first and read table to TBLH and Data Memory Increment table pointer low byte, TBLP, first and then the program code addressed by the table pointer (TBHP and TBLP) is moved to the specified Data Memory and the high byte moved to TBLH. [m] ← program code (low byte) TBLH ← program code (high byte) None Increment table pointer low byte first and read table (last page) to TBLH and Data Memory Increment table pointer low byte, TBLP, first and then the low byte of the program code (last page) addressed by the table pointer (TBLP) is moved to the specified Data Memory and the high byte moved to TBLH. [m] ← program code (low byte) TBLH ← program code (high byte) None Logical XOR Data Memory to ACC Data in the Accumulator and the specified Data Memory perform a bitwise logical XOR operation. The result is stored in the Accumulator. ACC ← ACC ″XOR″ [m] Z Logical XOR ACC to Data Memory Data in the specified Data Memory and the Accumulator perform a bitwise logical XOR operation. The result is stored in the Data Memory. [m] ← ACC ″XOR″ [m] Z Logical XOR immediate data to ACC Data in the Accumulator and the specified immediate data perform a bitwise logical XOR operation. The result is stored in the Accumulator. ACC ← ACC ″XOR″ x Z 280 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Extended Instruction Definition The extended instructions are used to directly access the data stored in any data memory sections. LADC A,[m] Description Operation Affected flag(s) LADCM A,[m] Description Operation Affected flag(s) LADD A,[m] Description Add Data Memory to ACC with Carry The contents of the specified Data Memory, Accumulator and the carry flag are added. The result is stored in the Accumulator. ACC ← ACC + [m] + C OV, Z, AC, C, SC Add ACC to Data Memory with Carry The contents of the specified Data Memory, Accumulator and the carry flag are added. The result is stored in the specified Data Memory. [m] ← ACC + [m] + C OV, Z, AC, C, SC Add Data Memory to ACC The contents of the specified Data Memory and the Accumulator are added. The result is stored in the Accumulator. Operation Affected flag(s) ACC ← ACC + [m] OV, Z, AC, C, SC LADDM A,[m] Description Add ACC to Data Memory The contents of the specified Data Memory and the Accumulator are added. The result is stored in the specified Data Memory. [m] ← ACC + [m] OV, Z, AC, C, SC Operation Affected flag(s) LAND A,[m] Description Operation Affected flag(s) Logical AND Data Memory to ACC Data in the Accumulator and the specified Data Memory perform a bitwise logical AND operation. The result is stored in the Accumulator. ACC ← ACC ″AND″ [m] Z Operation Affected flag(s) Logical AND ACC to Data Memory Data in the specified Data Memory and the Accumulator perform a bitwise logical AND operation. The result is stored in the Data Memory. [m] ← ACC ″AND″ [m] Z LCLR [m] Description Operation Affected flag(s) Clear Data Memory Each bit of the specified Data Memory is cleared to 0. [m] ← 00H None LCLR [m].i Description Operation Affected flag(s) Clear bit of Data Memory Bit i of the specified Data Memory is cleared to 0. [m].i ← 0 None LANDM A,[m] Description Rev. 1.00 281 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LCPL [m] Description Operation Affected flag(s) LCPLA [m] Description Operation Affected flag(s) Complement Data Memory Each bit of the specified Data Memory is logically complemented (1′s complement). Bits which previously contained a 1 are changed to 0 and vice versa. [m] ← [m] Z Complement Data Memory with result in ACC Each bit of the specified Data Memory is logically complemented (1′s complement). Bits which previously contained a 1 are changed to 0 and vice versa. The complemented result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC ← [m] Z Affected flag(s) Decimal-Adjust ACC for addition with result in Data Memory Convert the contents of the Accumulator value to a BCD (Binary Coded Decimal) value resulting from the previous addition of two BCD variables. If the low nibble is greater than 9 or if AC flag is set, then a value of 6 will be added to the low nibble. Otherwise the low nibble remains unchanged. If the high nibble is greater than 9 or if the C flag is set, then a value of 6 will be added to the high nibble. Essentially, the decimal conversion is performed by adding 00H, 06H, 60H or 66H depending on the Accumulator and flag conditions. Only the C flag may be affected by this instruction which indicates that if the original BCD sum is greater than 100, it allows multiple precision decimal addition. [m] ← ACC + 00H or [m] ← ACC + 06H or [m] ← ACC + 60H or [m] ← ACC + 66H C LDEC [m] Description Operation Affected flag(s) Decrement Data Memory Data in the specified Data Memory is decremented by 1. [m] ← [m] − 1 Z LDECA [m] Description Operation Affected flag(s) Decrement Data Memory with result in ACC Data in the specified Data Memory is decremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged. ACC ← [m] − 1 Z LINC [m] Description Operation Affected flag(s) Increment Data Memory Data in the specified Data Memory is incremented by 1. [m] ← [m] + 1 Z LINCA [m] Description Increment Data Memory with result in ACC Data in the specified Data Memory is incremented by 1. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged. ACC ← [m] + 1 Z LDAA [m] Description Operation Operation Affected flag(s) Rev. 1.00 282 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LMOV A,[m] Description Operation Affected flag(s) Move Data Memory to ACC The contents of the specified Data Memory are copied to the Accumulator. ACC ← [m] None LMOV [m],A Description Operation Affected flag(s) Move ACC to Data Memory The contents of the Accumulator are copied to the specified Data Memory. [m] ← ACC None LOR A,[m] Description Logical OR Data Memory to ACC Data in the Accumulator and the specified Data Memory perform a bitwise logical OR operation. The result is stored in the Accumulator. ACC ← ACC ″OR″ [m] Z Operation Affected flag(s) LORM A,[m] Description Operation Affected flag(s) LRL [m] Description Operation Affected flag(s) LRLA [m] Description Operation Affected flag(s) LRLC [m] Description Operation Affected flag(s) LRLCA [m] Description Operation Affected flag(s) Rev. 1.00 Logical OR ACC to Data Memory Data in the specified Data Memory and the Accumulator perform a bitwise logical OR operation. The result is stored in the Data Memory. [m] ← ACC ″OR″ [m] Z Rotate Data Memory left The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit 0. [m].(i+1) ← [m].i; (i=0~6) [m].0 ← [m].7 None Rotate Data Memory left with result in ACC The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit 0. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC.(i+1) ← [m].i; (i=0~6) ACC.0 ← [m].7 None Rotate Data Memory left through Carry The contents of the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces the Carry bit and the original carry flag is rotated into bit 0. [m].(i+1) ← [m].i; (i=0~6) [m].0 ← C C ← [m].7 C Rotate Data Memory left through Carry with result in ACC Data in the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces the Carry bit and the original carry flag is rotated into the bit 0. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC.(i+1) ← [m].i; (i=0~6) ACC.0 ← C C ← [m].7 C 283 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LRR [m] Description Operation Affected flag(s) LRRA [m] Description Operation Affected flag(s) LRRC [m] Description Operation Affected flag(s) LRRCA [m] Description Operation Affected flag(s) LSBC A,[m] Description Operation Affected flag(s) LSBCM A,[m] Description Operation Affected flag(s) Rev. 1.00 Rotate Data Memory right The contents of the specified Data Memory are rotated right by 1 bit with bit 0 rotated into bit 7. [m].i ← [m].(i+1); (i=0~6) [m].7 ← [m].0 None Rotate Data Memory right with result in ACC Data in the specified Data Memory is rotated right by 1 bit with bit 0 rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC.i ← [m].(i+1); (i=0~6) ACC.7 ← [m].0 None Rotate Data Memory right through Carry The contents of the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces the Carry bit and the original carry flag is rotated into bit 7. [m].i ← [m].(i+1); (i=0~6) [m].7 ← C C ← [m].0 C Rotate Data Memory right through Carry with result in ACC Data in the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces the Carry bit and the original carry flag is rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the Data Memory remain unchanged. ACC.i ← [m].(i+1); (i=0~6) ACC.7 ← C C ← [m].0 C Subtract Data Memory from ACC with Carry The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. ACC ← ACC − [m] − C OV, Z, AC, C, SC, CZ Subtract Data Memory from ACC with Carry and result in Data Memory The contents of the specified Data Memory and the complement of the carry flag are subtracted from the Accumulator. The result is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. [m] ← ACC − [m] − C OV, Z, AC, C, SC, CZ 284 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LSDZ [m] Description Operation Affected flag(s) Skip if decrement Data Memory is 0 The contents of the specified Data Memory are first decremented by 1. If the result is 0 the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. [m] ← [m] − 1 Skip if [m]=0 None Affected flag(s) Skip if decrement Data Memory is zero with result in ACC The contents of the specified Data Memory are first decremented by 1. If the result is 0, the following instruction is skipped. The result is stored in the Accumulator but the specified Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0, the program proceeds with the following instruction. ACC ← [m] − 1 Skip if ACC=0 None LSET [m] Description Operation Affected flag(s) Set Data Memory Each bit of the specified Data Memory is set to 1. [m] ← FFH None LSET [m].i Description Operation Affected flag(s) Set bit of Data Memory Bit i of the specified Data Memory is set to 1. [m].i ← 1 None LSIZ [m] Description Skip if increment Data Memory is 0 The contents of the specified Data Memory are first incremented by 1. If the result is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. [m] ← [m] + 1 Skip if [m]=0 None LSDZA [m] Description Operation Operation Affected flag(s) LSIZA [m] Description Operation Affected flag(s) LSNZ [m].i Description Operation Affected flag(s) Rev. 1.00 Skip if increment Data Memory is zero with result in ACC The contents of the specified Data Memory are first incremented by 1. If the result is 0, the following instruction is skipped. The result is stored in the Accumulator but the specified Data Memory contents remain unchanged. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. ACC ← [m] + 1 Skip if ACC=0 None Skip if Data Memory is not 0 If the specified Data Memory is not 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is 0 the program proceeds with the following instruction. Skip if [m].i ≠ 0 None 285 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LSNZ [m] Description Operation Affected flag(s) LSUB A,[m] Description Operation Affected flag(s) Skip if Data Memory is not 0 If the content of the specified Data Memory is not 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is 0 the program proceeds with the following instruction. Skip if [m] ≠ 0 None Subtract Data Memory from ACC The specified Data Memory is subtracted from the contents of the Accumulator. The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. ACC ← ACC − [m] OV, Z, AC, C, SC, CZ Operation Affected flag(s) Subtract Data Memory from ACC with result in Data Memory The specified Data Memory is subtracted from the contents of the Accumulator. The result is stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1. [m] ← ACC − [m] OV, Z, AC, C, SC, CZ LSWAP [m] Description Operation Affected flag(s) Swap nibbles of Data Memory The low-order and high-order nibbles of the specified Data Memory are interchanged. [m].3~[m].0 ↔ [m].7~[m].4 None LSWAPA [m] Description Swap nibbles of Data Memory with result in ACC The low-order and high-order nibbles of the specified Data Memory are interchanged. The result is stored in the Accumulator. The contents of the Data Memory remain unchanged. ACC.3~ACC.0 ← [m].7~[m].4 ACC.7~ACC.4 ← [m].3~[m].0 None LSUBM A,[m] Description Operation Affected flag(s) LSZ [m] Description Operation Affected flag(s) LSZA [m] Description Operation Affected flag(s) Rev. 1.00 Skip if Data Memory is 0 If the contents of the specified Data Memory is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. Skip if [m]=0 None Skip if Data Memory is 0 with data movement to ACC The contents of the specified Data Memory are copied to the Accumulator. If the value is zero, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program proceeds with the following instruction. ACC ← [m] Skip if [m]=0 None 286 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM LSZ [m].i Description Operation Affected flag(s) LTABRD [m] Description Operation Affected flag(s) LTABRDL [m] Description Operation Affected flag(s) LITABRD [m] Description Operation Skip if bit i of Data Memory is 0 If bit i of the specified Data Memory is 0, the following instruction is skipped. As this requires the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0, the program proceeds with the following instruction. Skip if [m].i=0 None Read table (current page) to TBLH and Data Memory The low byte of the program code (current page) addressed by the table pointer (TBLP) is moved to the specified Data Memory and the high byte moved to TBLH. [m] ← program code (low byte) TBLH ← program code (high byte) None Read table (last page) to TBLH and Data Memory The low byte of the program code (last page) addressed by the table pointer (TBLP) is moved to the specified Data Memory and the high byte moved to TBLH. [m] ← program code (low byte) TBLH ← program code (high byte) None Increment table pointer low byte first and read table to TBLH and Data Memory Increment table pointer low byte, TBLP, first and then the program code addressed by the table pointer (TBHP and TBLP) is moved to the specified Data Memory and the high byte moved to TBLH. [m] ← program code (low byte) TBLH ← program code (high byte) Affected flag(s) None LITABRDL [m] Description Increment table pointer low byte first and read table (last page) to TBLH and Data Memory Increment table pointer low byte, TBLP, first and then the low byte of the program code (last page) addressed by the table pointer (TBLP) is moved to the specified Data Memory and the high byte moved to TBLH. [m] ← program code (low byte) TBLH ← program code (high byte) None Operation Affected flag(s) LXOR A,[m] Description Operation Affected flag(s) LXORM A,[m] Description Operation Affected flag(s) Rev. 1.00 Logical XOR Data Memory to ACC Data in the Accumulator and the specified Data Memory perform a bitwise logical XOR operation. The result is stored in the Accumulator. ACC ← ACC ″XOR″ [m] Z Logical XOR ACC to Data Memory Data in the specified Data Memory and the Accumulator perform a bitwise logical XOR operation. The result is stored in the Data Memory. [m] ← ACC ″XOR″ [m] Z 287 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Package Information Note that the package information provided here is for consultation purposes only. As this information may be updated at regular intervals users are reminded to consult the Holtek website for the latest version of the package information. Additional supplementary information with regard to packaging is listed below. Click on the relevant section to be transferred to the relevant website page. • Further Package Information (include Outline Dimensions, Product Tape and Reel Specifications) • Packing Meterials Information • Carton information Rev. 1.00 288 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 48-pin LQFP (7mm × 7mm) Outline Dimensions Symbol Dimensions in inch Min. Nom. Max. A — 0.354 BSC — B — 0.276 BSC — C — 0.354 BSC — D — 0.276 BSC — E — 0.020 BSC — F 0.007 0.009 0.011 G 0.053 0.055 0.057 H — — 0.063 I 0.002 — 0.006 J 0.018 0.024 0.030 K 0.004 — 0.008 α 0° ― 7° Symbol Rev. 1.00 Dimensions in mm Min. Nom. Max. A — 9.000 BSC — B — 7.000 BSC — C — 9.000 BSC — D — 7.000 BSC — E — 0.500 BSC — F 0.170 0.220 0.270 G 1.350 1.400 1.450 H — — 1.600 I 0.050 — 0.150 J 0.450 0.600 0.750 K 0.090 — 0.200 α 0° ― 7° 289 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 64-pin LQFP (7mm × 7mm) Outline Dimensions Symbol Min. Nom. A — 0.354 BSC — B — 0.276 BSC — C — 0.354 BSC — D — 0.276 BSC — E — 0.016 BSC — F 0.005 0.007 0.009 G 0.053 0.055 0.057 H — — 0.063 I 0.002 — 0.006 J 0.018 0.024 0.030 K 0.004 — 0.008 α 0° — 7° Symbol Rev. 1.00 Dimensions in inch Max. Dimensions in mm Min. Nom. Max. A — 9.00 BSC — B — 7.00 BSC — C — 9.00 BSC — D — 7.00 BSC — E — 0.40 BSC — 0.23 F 0.13 0.18 G 1.35 1.40 1.45 H — — 1.60 I 0.05 — 0.15 J 0.45 0.60 0.75 K 0.09 — 0.20 α 0° — 7° 290 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM 80-pin LQFP (10mm×10mm) Outline Dimensions Symbol Nom. Max. A ― 0.472 BSC ― B ― 0.394 BSC ― C ― 0.472 BSC ― D ― 0.394 BSC ― E ― 0.016 BSC ― F 0.007 0.009 0.011 G 0.053 0.055 0.057 H ― ― 0.063 I 0.002 ― 0.006 J 0.018 0.024 0.030 K 0.004 ― 0.008 α 0° ― 7° Symbol Rev. 1.00 Dimensions in inch Min. Dimensions in mm Min. Nom. Max. A — 12.00 BSC — B — 10.00 BSC — C — 12.00 BSC — D — 10.00 BSC — E ― 0.40 BSC ― 0.23 F 0.13 0.18 G 1.35 1.4 1.45 H ― ― 1.60 I 0.05 — 0.15 J 0.45 0.60 0.75 K 0.09 ― 0.20 α 0° ― 7° 291 December 06, 2016 HT67F2350/HT67F2360 HT67F2370/HT67F2390 Advanced A/D Flash MCU with LCD & EEPROM Copyright© 2016 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek's products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw/en/home. Rev. 1.00 292 December 06, 2016