FES16AT THRU FES16JT FAST EFFICIENT PLASTIC RECTIFIER Reverse Voltage - 50 to 600 Volts Forward Current - 16.0 Amperes TO-220AC FEATURES 0.185 (4.70) 0.415 (10.54) MAX. 0.175 (4.44) 0.370 (9.40) 0.154 (3.91) 0.360 (9.14) 0.055 (1.39) DIA. 0.148 (3.74) 0.045 (1.14) 0.113 (2.87) 0.103 (2.62) 0.145 (3.68) 0.135 (3.43) 0.560 (14.22) 0.530 (13.46) 0.410 (10.41) 0.390 (9.91) 0.350 (8.89) 0.635 (16.13) 0.330 (8.38) 0.625 (15.87) 1.148 (29.16) PIN 1 2 1.118 (28.40) 0.110 (2.79) 0.100 (2.54) 0.160 (4.06) 0.140 (3.56) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ Glass passivated chip junction ♦ Low power loss ♦ Low forward voltage, high current capability ♦ High surge current capability ♦ Superfast recovery time, for high efficiency ♦ High temperature soldering guaranteed: 250°C, 0.16" (4.06mm) from case for 10 seconds 0.560 (14.22) 0.530 (13.46) 0.105 (2.67) 0.095 (2.41) 0.037 (0.94) 0.027 (0.68) MECHANICAL DATA 0.022 (0.56) 0.014 (0.36) PIN 1 0.205 (5.20) 0.195 (4.95) PIN 2 CASE Case: JEDEC TO-220AC molded plastic body over passivated chips Terminals: Plated lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Weight: 0.064 ounce, 1.81 grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. FES SYMBOLS 16AT FES 16BT FES 16CT FES 16DT FES 16FT FES 16GT FES 16HT FES 16JT UNITS Maximum repetitive peak reverse voltage VRRM 50 100 150 200 300 400 500 600 Volts Maximum RMS voltage VRMS 35 70 105 140 210 280 350 420 Volts Maximum DC blocking voltage VDC 50 100 150 200 300 400 500 600 Volts Maximum average forward rectified current at TC=100°C I(AV) 16.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) at TC=100°C IFSM 250.0 Amps Maximum instantaneous forward voltage at 16A VF Maximum DC reverse current at rated DC blocking voltage TC=25°C TC=100°C 0.975 1.3 10.0 500.0 IR Maximum reverse recovery time (NOTE1) trr Typical junction capacitance (NOTE 2) CJ 175.0 RΘJA RΘJC 16.0 1.2 Typical thermal resistance (NOTE 3) Operating and storage temperature range NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr =0.25A (2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to case and ambient mounted on heatsink 4/98 TJ, TSTG 1.5 35.0 µA 50.0 -65 to +150 Volts ns 145.0 pF °C/W °C RATINGS AND CHARACTERISTICS CURVES FES16AT THRU FES16JT FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT AVERAGE FORWARD CURRENT, AMPERES 20 RESISTIVE OR INDUCTIVE LOAD 16 12 8.0 4.0 0 PEAK FORWARD SURGE CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 300 250 200 150 100 50 0 0 50 100 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) TC=100°C 150 1 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 1,000 80 TJ =125°C 10 50-200V 300-400V 500-600V 1 TJ = 25°C PULSE WIDTH = 300µs 1% DUTY CYCLE 0.1 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, VOLTS INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 NUMBER OF CYCLES AT 60 HZ CASE TEMPERATURE, °C 100 C 25° TJ= 10 °C 100 TJ = 50-200V 1 300-600V C 25° TJ= 0.1 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 1,000 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 100 50-400V 500-600V 10 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 100