-500mA / -12V Low VCE (sat) Digital transistors (with built-in resistors) DTB523YE / DTB523YM Dimensions (Unit : mm) Applications Inverter, Interface, Driver DTB523YE 0.7 1.6 0.55 0.3 Feature 1) VCE (sat) is lower than conventional products. 2) Built-in bias resistors enable the configuration of an inverter circuit without connecting external input resistors (see equivalent circuit). 3) The bias resistors consist of thin-film resistors with complete isolation to allow positive biasing of the input. They also have the advantage of almost completely eliminating parasitic effects. 4) Only the on / off conditions need to be set for operation, making the device design easy. (2) 1.6 0.8 (3) 0.2 0.15 0.5 0.5 EMT3 JEITA No. (SC-75A) JEDEC No. <SOT-416> 0.1Min. (1) 0.2 1.0 (1) GND (2) IN (3) OUT Each lead has same dimensions Abbreviated symbol : X53 1.2 0.32 Structure PNP epitaxial plannar silicon transistor (Resistor built-in type) 0.2 DTB523YM 0.8 1.2 (3) (1)(2) 0.4 0.4 0.2 0.22 0.13 0.5 0.8 (1) IN (2) GND (3) OUT VMT3 Each lead has same dimensions Packaging specifications Abbreviated symbol : X52 Package EMT3 VMT3 Packaging type Taping Taping TL T2L 3000 8000 Code Part No. Basic ordering unit (pieces) − DTB523YE − DTB523YM Absolute maximum ratings (Ta=25C) Symbol Parameter Inner circuit Limits DTB523YE DTB523YM Unit VCC −12 V Input voltage VIN −12 to +5 V −500 mA Collector current ∗1 IC (max) Power dissipation ∗2 PD 150 mW Tj 150 C Junction temperature Storage temperature Tstg −55 to +150 C ∗1 Characteristics of built-in transistor. ∗2 Each terminal mounted on a recommended land. www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ OUT R1 Supply voltage IN R2 GND(+) OUT IN GND(+) R1=2.2kΩ / R2=10kΩ 1/2 2010.01- Rev.C DTB523YE / DTB523YM Data Sheet Electrical characteristics (Ta=25C) Parameter Symbol Min. Typ. Max. VI(off) − − −0.3 VI(on) −2.5 − − VO(on) − −60 −300 mV IO/II= −100mA / −5mA II − − −3.0 mA VI= −5V IO(off) − − −0.5 μA VCC= −12V, VI=0V DC current gain GI 140 − − − Transition frequency ∗ fT − 260 − MHz Input resistance R1 1.54 2.2 2.86 kΩ − Resistance ratio R2/R1 3.6 4.5 5.5 − − Input voltage Output voltage Input current Output current Unit Conditions VCC= −5V, IO= −100μA V VO= −0.3V, IO= −20mA VO= −2V, IO= −100mA VCE= −10V, IE=5mA, f=100MHz ∗ Characteristics of built-in transistor. Electrical characteristics curves Ta= －40℃ 25℃ 85℃ 10 125℃ 1 0.1 0.01 100 V0 = -0.3V OUTPUT CURRENT : I O (mA) INPUT VOLTAGE : V I (on) (V) 100 VCC = -5V 10 Ta=125℃ 85℃ 1 25℃ －40℃ 0.1 0.1 1 10 100 0 1000 0.2 DC CURENT GAIN : G I Ta=125℃ 85℃ 25℃ 100 －40℃ 10 1 0.1 0.6 0.8 1 1 VO= -2V OUTPUT VOLTAGE : VO(on) (V) 1000 0.4 1.2 1.4 INPUT VOLTAGE : VI(off) (V) OUTPUT CURRENT : IO (mA) IC /II=20 Ta=125℃ 85℃ 25℃ －40℃ 0.1 0.01 1 10 100 OUTPUT CURENT : IO (mA) 1000 www.rohm.com c 2010 ROHM Co., Ltd. All rights reserved. ○ 1 10 100 1000 OUOPUT CURRENT : IO (mA) 2/2 2010.01- Rev.C Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A