Miniature Slides Series MS Distinctive Characteristics Bright, LED illumination at top of actuator. Over-center actuator block and plunger design gives crisp actuation, diminishes sparking, and increases operating life. Guide interlocked with actuator block prevents window locking and maintains correct plunger alignment to assure contact stability. Antijamming design protects contacts from damage due to excessive downward force on the actuator. High internal barriers between poles and insulating sheet between case and actuator block give added protection to contacts. Prominent external insulating barriers increase insulation resistance and dielectric strength. Epoxy sealed terminals prevent entry of flux, solvents, and other contaminants. Clinching of frame to case well above base and terminals provides 1,500V dielectric strength. Actual Size NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 07-07 Miniature Slides Series MS General Specifications Electrical Capacity (Resistive Load) Power Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Contact Timing: Total Travel: Materials & Finishes Actuator: Frame: Case: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Processing Soldering Time & Temp: Cleaning: Standards & Certifications Flammability Standards: 6A @ 125V AC or 3A @ 250V AC 10 milliohms maximum 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 50,000 operations minimum 25,000 operations minimum Nonshorting (break-before-make) .087” (2.2mm) Glass fiber reinforced polyester Stainless steel Glass fiber reinforced diallyl phthalate resin (UL94V-0) Silver alloy Silver capped copper with silver plating Copper or brass with silver plating –10°C through +55°C (+14°F through +131°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering Recommended (PC version): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Note: Lever must be in center position while soldering. These devices are not process sealed. Hand clean locally using alcohol based solution. UL94V-0 rated case NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 07-07 Series MS Miniature Slides TYPICAL SWITCH ORDERING EXAMPLE MS 1 2 POLES 1 L F L 01 LED Lighted MOUNTING 2 ON NONE ON 3 ON OFF ON LEDS Silver; Rated 6A @ 125V AC & 3A @ 250V AC W CIRCUITS C CONTACT MATERIALS & RATINGS ILLUMINATION SPDT W N For Straight PC (Terminal 03 only) F With 2-screw Flange (Terminal 01 only) C Red E Yellow F Green TERMINALS 01 Solder Lug 03 Straight PC DESCRIPTION FOR TYPICAL ORDERING EXAMPLE MS12LFW01C Red LED Illumination 2-screw Flange Frame Silver Contacts with 6-Amp Rating SPDT ON-NONE-ON Circuit Solder Lug Terminals POLES & CIRCUITS Slide Position Pole SP Connected Terminals Left Center Right MS12 ON NONE ON MS13 ON OFF ON Left Center Throw & Schematics Right Model Note: Terminal numbers are not actually on the switch. LED circuit is isolated and requires an external connection. 2 (COM) 2-1 OPEN 2-3 SPDT L(+) 1 3 4 L(-) 6 CONTACT MATERIALS & RATINGS W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 07-07 Series MS Miniature Slides MOUNTING TYPES & TERMINALS N F Straight PC Mount (Combines with Straight PC Terminal 03 only) 03 2-screw Flange (Combines with Solder Lug Terminal 01 only) 01 Straight PC (6.35) (4.8) .250 .189 Epoxy Seal (1.17) Typ .046 (4.8) .189 Thk = (0.8) Typ .031 (2.0) .079 (4.0) .157 Epoxy Seal Solder Lug (6.35) (4.8) .250 .189 (2.0) .079 (1.1) .043 (1.17) .046 (4.8) .189 Thk = (0.8) Typ .031 LED COLORS & SPECIFICATIONS LEDs are supplied as an integral part of the switch (not available separately). The lamp circuit is independent of switch operation. Electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula given in the Supplement. (+) (-) C Color E Red F Yellow Green Forward Peak Current IFM 30mA 30mA 25mA Continuous Forward Current IF 16mA 16mA 16mA Forward Voltage VF 1.98V 2.06V 2.16V Reverse Peak Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆IF 0.40mA/°C 0.42mA/°C 0.33mA/°C Ambient Temperature Range –15° ~ +60°C TYPICAL SWITCH DIMENSIONS Solder Lug Terminals (1.2) R Typ .047 (5.0) .197 Circuit Mark This Side (2.0) Typ .079 (6.1) .240 (8.2) .323 (5.1) .201 (12.7) .500 2 (4.7) Typ .185 (17.53) .690 (0.5) .020 (4.8) .189 (11.9) .469 (0.4) (4.5) .016 .177 (7.6) (6.35) .299 .250 (6.8) .268 1 4 Direction of Actuation (3.8) .150 (2.4) .094 Dia Typ 3 6 (17.53) .690 (19.6) .772 (2.0) .079 MS12LFW01C (1.17) Typ .046 (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 (9.0) .354 Maximum Panel Thickness .197” (5.0mm) Actuator in LEFT Position Straight PC Terminals Circuit Mark This Side (5.0) .197 (1.17) Typ .046 (0.8) Typ .031 (3.8) .150 (2.0) .079 (8.2) .323 MS12LNW03C (4.7) Typ .185 (5.1) .201 (7.6) .299 Actuator in LEFT Position (4.8) .189 (6.35) .250 3 3 2 (12.7) .500 (4.8) .189 (11.9) .469 (0.5) .020 (4.7) Typ .185 2 1 1 4 6 (6.8) .268 4 (1.8) Dia Typ .073 (9.0) .354 Direction of Actuation 6 (4.8) .189 Maximum Panel Thickness .197” (5.0mm) NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 07-07