Embedded Power for Business-Critical Continuity Rev. 06.10.11_52 DS2000-3 1 of 4 DS2000-3 2000 Watts 12 V Distributed Power System Distributed Power Bulk Front-End Total Output Power: 2000 Watts +12 Vdc main Output +3.3 Vdc Stand-by Output Wide Range Input voltage: 90 - 264 Vac Electrical Specifications Special Features • Active power factor correction • EN61000-3-2 harmonic compliance • Active AC inrush control • 1U X 3U form factor • 26.14 W / in3 • +12 Vdc output • +3.3 Vdc Stand-By (5 V standby - consult factory) • No minimum load required • Hot plug operation • N + 1 redundant • Internal OR’ing fets • Active current sharing (10 - 100% load) • Built-in cooling fans (40 mm x 28 mm) • I2C communication interface bus • PM Bus compliant • EERPOM for FRU data • Red/Green bi-color LED status • Internal fan speed control • INTEL, SSI Std. logic timing • INTEL, SSI Std. FRU data format • One year warranty Safety • UL/cUL 60950 (UL Recognized) • NEMKO+ CB Report EN60950 • EN60950 • CE Mark • China CCC Input Input range 90 - 264 Vac (wide range) 90 - 264 1200 W load, nominal 100 Vac 180 - 264 2000 W load, nominal 200 Vac Frequency 47 - 63 Hz, single phase AC Inrush current Efficiency 55 A maximum inrush current > 89% typical at full load, high line Conducted EMI FCC Subpart J EN55022 Class B Radiated EMI FCC Subpart J EN55022 Class B Power factor 0.99 typical Leakage current 1.40 mA @ 240 Vac Hold up time 12 ms minimum Output Main DC voltage Stand-By Adjustment range Regulation Overcurrent Overvoltage Undervoltage Turn-on delay +12 V Output Rise Time +12 V @ 164.2 A 180 - 264 Vac +12 V @ 100 A 90 - 264 Vac +3.3 Vsb @ 9 A (5 V @ 5 A TBA) Factory Set, no pot adjustments +12 Vdc; ±5% +3.3 Vsb; ±5% +12 Vdc; latches off if overcurrent lasts over 1 second, otherwise it is auto recovery (See ordering info next page) +3.3 Vsb, 9 A max (same as +12 Vdc) +12 Vdc; 13.2 - 14.4 Vdc +3.3 Vsb; 3.76 - 4.30 Vdc +12 Vdc; 9 - 10.8 V (latch off) 2 second max, 5 - 300 ms, Monotonic Rise 5 - 50 ms, Monotonic Rise Embedded Power for Business-Critical Continuity Rev. 06.10.11_52 DS2000-3 2 of 4 Logic Control PS_SEATED TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed. PWR GOOD AC OK Active TTL LOW when output is within regulation limits. A LOW logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 2 mS early warning signal before 12.0 V DC output loss of regulation. PS_INHIBIT/PS_KILL This signal is connected to a short pin on the PSU. When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. Environmental Specifications Operating temperature -10 °C to 50 °C Storage temperature -40 °C to +85 °C Altitude, operating 10,000 ft Electromagnetic susceptibility / Input transients -EN61000-3-2, -3-3 -EN61000-4-2, 4.3, 4-4, -4-5, 4-11 Level -EN55024:1998 RoHS & lead-free compliant (no tantalum caps) Humidity 20 to 90% RH, non-condensing Shock and vibration Specifications complies with Astec Std. Specifications, Q3205 MTBF (Demonstrated) 500 K Hrs at full load, 40 °C Ordering Information Model Number DS2000-3 DS2000-3-001 Nominal Output Voltage Set Point 12.2 Vdc 3.3 Vsb 12.2 Vdc 3.3 Vsb Set Point Tolerance ±0.2% ±1% ±0.2% ±1% Total Regulation ±5% ±5% ±5% ±5% Minimum Current 0A 0A 0A 0A Maximum Current 161.5 A 9.0 A 161.5 A** 9.0 A Output Ripple P/P 120 mV 60 mV 120 mV 60 mV *Overcurrent latches off if overcurrent lasts over 1 second, otherwise it is auto recovery. *For 5 Vsb, consult marketing. ** Derates per below curve (-001) reverse air DS2000-3-001 Derating Curve Output Power (W) 2500 2000 1500 1000 500 0 -10 -5 0 5 10 15 20 25 30 35 40 45 50 Operating Temperature (°C) Low Line (90 Vac) High Line (180 Vac) Overcurrent 120 - 130% of nominal 100 - 125% of nominal 120 - 130% of nominal 100 - 125% of nominal Airflow Standard Reverse Embedded Power for Business-Critical Continuity Rev. 06.10.11_52 DS2000-3 3 of 4 Mechanical Drawing Condition LED Status +3V3SB-ON; +12VOUT-OFF; AC PRESENT Blinking Green +3V3SB-ON, +12VOUT-ON Solid Green +12V_OCP, +12V_UVP, +48OVP Blinking Red FAN_FAULT, OTP, 3V3 OCP/UVP Solid Red 295.7 ± 1 (3X) 261.7 (3X) EMI Gasket Laird Technologies (SEA) PTE S3700-0021-00 Programming Holes 3.2 106.7 ± 0.8 LABEL ORIENTATION THIS SIDE UP 8 Latch EMI Gasket Laird Technologies (SEA) PTE S3700-0021-00 AIRFLOW DIRECTION 325.2 16.3 ± 0.8 YELLOW WAVE LENGTH: 590 OUTPUT CONNECTOR MOLEX 45985-1462 99.1 ± 0.8 325.2 40370111360 Handle EMI Gasket Laird Technologies (SEA) PTE S3700-0021-00 13.7 ± 0.8 220.1 AC INLET 40 ± 0.8 22 32 GREEN WAVE LENGTH: 565 100.2 72.2 292.1 ± 1 220.1 Embedded Power for Business-Critical Continuity Americas DC Output Connector Pinout / Functions 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Unit Connector; Molex Blade, (LPH Series) 45985-xxx Mating Connector; Molex Blade, (LPH Series) SD-45984-1462 Signal Descriptions Signal Pin Signal Pin Signal Signal Signal Signal #Comp Side #Solder Side Function Description Function Description Top Row Bottom Row A17 3.3V Sense RTN 3.3V Sen Rtn A1 SPARE A18 AC OK# AC input present A2 SPARE A3 #ALERT A19 A0 I2C address bit 0 A20 A2 I2C address bit 2 A4 A1 I2C address bit 1 2 A5 SDA I2C Data signal A21 SCL* I C Clock signal A22 PWOK# Pwr OK output A6 PRESENT# Power supply present 12V load share bus A7 PSON# Power enable input A23 12LS A24 +12VRS Rtn +12V Rmt Sen Rtn A8 +12V RS +12V Remote Sense A25 3.3vsb Stand-By A9 3.3vsb Stand-By A26 3.3vsb Stand-By A10 3.3vsb Stand-By A27 3.3vsb Stand-By A11 3.3vsb Stand-By A28 3.3vsb Stand-By A12 3.3vsb Stand-By A29 3.3vsb Rtn Stand-By return A13 3.3vsb Rtn Stand-By return A30 3.3vsb Rtn Stand-By return A14 3.3vsb Rtn Stand-By return 3.3vsb Rtn Stand-By return A15 3.3vsb Rtn Stand-By return A31 A32 3.3vsb Rtn Stand-By return A16 3.3vsb Rtn Stand-By return Power Blade PB1 Top PB2 Top PB3 Top PB4 Top PB5 Top +12vdc +12vdc +12vdc +12vdc Rtn +12vdc Rtn Power Blade PB1 Bottom +12vdc PB2 Bottom +12vdc PB3 Bottom +12vdc Rtn PB4 Bottom +12vdc Rtn PB5 Bottom +12vdc Rtn Main Output Main Output Main Output Main Output Main Output Rev. 06.10.11_52 DS2000-3 4 of 4 Main Output Main Output Main Output Main Output Main Output *Supports I2C standard mode (100 kHz) only Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.Emerson.com/EmbeddedPower techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Mating Connector - Molex p/n: 45984-1462 Signal Pin A1 Bottom Left Signal Pin A17 Top Left Embedded Computing Embedded Power Monitoring PB1 PB2 PB3 PB4 Outside Plant PB5 Power Switching & Controls Precision Cooling A17 OPTIONAL GUIDES Racks & Integrated Cabinets Services TOP ROW BOTTOM ROW TOP ROW BOTTOM ROW Surge Protection EmersonNetworkPower.com A1 NO OF SIGNALS OPTIONAL SEE CHART OPTIONAL PEGS Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2011 Emerson Electric Co.