DATA SHEET GBPC12,15,25 AND 35 Series SEMICONDUCTOR GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Current Voltage - 12.0 to 35.0 Amperes FEATURES •The plastic package has Underwriters Laboratory Flammability Classification 94V-0 •This series is UL recognized under component index, file number E54214 •Integrally molded heatsink provides very low thermal resistance for maximum heat dissipation •Universal 3-way terminals; snap-on, wire wrap-around, or P.C.B. mounting •High forward surge current capabilities •Glass passivated chip junctions •Typical IR less than 0.3mA •High temperature soldering guaranteed: 260°C/10 seconds at 5lbs. (2.3 kg) tension •High temperature soldering : 260OC / 10 seconds at terminals •Pb free product at available : 99% Sn above meet RoHS environment substance directive request MECHANICAL DATA •Case: Molded plastic with heatsink integrally mounted in the bridge encapsulation •Terminals: Either plated 0.25" (6.35mm). Faston lugs or plated copper leads 0.040" (1.02mm) diameter. Suffix letter "W" added to indicate leads (e.g. GBPC12005W). •Mounting Position: See NOTE 3 •Polarity: Polarity symbols molded on body •Mounting Torque: 20 in. - lb. max. Weight: 0.53 ounce, 15 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified output current (SEE FIG.1) Peak forward surge current single sine-wave superimposed on rated load (JEDEC Method) Rating (non-repetitive, for t greater than 1ms and less than 8.3ms) for fusing Maximum instantaneous forward voltage drop per leg at SYMBOLS VRRM VRMS VDC GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 GBPC15 GBPC25 GBPC35 GBPC12 IF=6.0A GBPC15 IF=7.5A GBPC25 IF=12.5A GBPC35 IF=17.5A TA=25°C TA=125°C I(AV) IFSM I2t VF Maximum reverse DC current at rated DC blocking voltage per leg RMS isolation voltage from case to leads Typical junction capacitance per leg (NOTE 1) Typical thermal resistance per leg (NOTE 2) GBPC12-25 GBPC35 Operating junction storage temperature range IR VISO CJ RQJC TJ, TSTG 005 50 35 50 01 100 70 100 GBPC12, 15, 25, 35 02 04 06 08 200 400 600 800 140 280 420 560 200 400 600 800 12.0 15.0 25.0 35.0 200.0 300.0 300.0 400.0 160.0 375.0 375.0 660.0 1.1 5.0 500.0 2500.0 300.0 1.9 1.4 -55 to +150 10 1000 700 1000 UNITS Volts Volts Volts Amps Amps A2 sec Volts uA Volts pF °C/W °C NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Thermal resistance from junction to case per leg (3) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer efficiency with #10 screw http://www.yeashin.com 1 REV.02 20110725 DEVICE CHARACTERISTICS GBPC12,15,25 AND 35 Series FIG. 1 - MAXIMUM OUTPUT RECTIFIED CURRENT FIG. 2 - MAXIMUM OUTPUT RECTIFIED CURRENT 40 30 RthS-A=0.5 °C/W AVERAGE FORWARD CURRENT, AMPERES GBPC35 35 AVERAGE FORWARD CURRENT, AMPERES 40 BRIDGES MOUNTED on 9 x 3.5 x 4.6” (22.9 x 8.9 x 11.7cm) AL. FINNED PLATE 5 x 6 x 4.9” AL. FINNED PLATE GBPC25 25 5 x 4 x 3” AL. FINNED PLATE 20 GBPC15 15 6.0 x 2.2 x 2.2” AL. FINNED PLATE GBPC12 10 5 0 35 30 25 50 GBPC25 RthS-A=0.5 °C/W 25 20 GBPC15 RthS-A=1.0 °C/W 15 10 60 Hz RESISTIVE OR INDUCTIVE LOAD 0 60 HZ RESISTIVE OR INDUCTIVE LOAD GBPC35 5 0 75 100 125 150 175 200 GBPC12 RthS-A=1.0 °C/W 0 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE, °C CASE TEMPERATURE, °C FIG. 4 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG FIG. 3 - MAXIMUM POWER DISSIPATION 500 PEAK FORWARD SURGE CURRENT, AMPERES 80 AVERAGE POWER DISSIPATION OF BRIDGE, WATTS CAPACITIVE LOAD 70 60 TJ=TJ max. 50 40 30 RESISTIVE OR INDUCTIVE LOAD 20 TJ=TJ max. 0.5Single Sine-Wave (JEDEC Method) GBPC35 GBPC15 GBPC25 100 GBPC12 1.0 CYCLE 1 100 10 NUMBER OF CYCLES AT 60Hz 10 0 0 10 20 30 40 AVERAGE OUTPUT CURRENT, AMPERES http://www.yeashin.com 2 REV.02 20110725 DEVICE CHARACTERISTICS GBPC12,15,25 AND 35 Series FIG. 6 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG. 5 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG TJ=125°C 100 TJ=150°C INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 0.01 0.4 0.6 0.8 1 1.2 1.4 1.6 50-400V 600-1000V 10 1 0.1 TJ=25°C INSTANTANEOUS FORWARD VOLTAGE, VOLTS 0.01 0 20 80 60 40 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 7 - TYPICAL JUNCTION CAPACITANCE PER LEG FIG. 8 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG TJ=25°C f=1.0 MHz Vsig=50mVp-p 100 TRANSIENT THERMAL IMPEDANCE, °C/W JUNCTION, CAPACITANCE, pF 600 100 50 10 1 100 TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 0.1 0.01 REVERSE VOLTAGE, VOLTS 0.1 10 1 100 t, HEATING TIME, sec. http://www.yeashin.com 3 REV.02 20110725 GBPC12,15,25 AND 35 Series GBPC35 FIG. 9 1.135 (28.8) 1.115 (28.3) Hole for #10 Screw 0.220 (5.59) DIA. 0.200 (5.08) 0.672 (17.1) 0.632 (16.1) AC 1.135 (28.8) 1.115 (28.3) 0.672 (17.1) 0.632 (16.1) 0.582 (14.8) 0.542 (13.8) 0.732 (18.6) 0.692 (17.6) 0.094 (2.4) DIA. 0.25 (6.35) 0.034 (0.86) 0.030 (0.76) 0.840 (21.3) 0.740 (18.8) 0.310 (7. 87) 0.290 (7.36) GBPC-W FIG. 10 1.135 (28.8) 1.115 (28.3) Hole for #10 Screw 0.220 (5.59) DIA. 0.200 (5.08) 0.732 (18.6) 0.692 (17.6) 1.135 (28.8) 0.24 (6.0) 0.18 (4.6) 0.732 (18.6) 0.692 (17.6) 1.115 (28.3) 0.470 (11.9) 0.430 (10.9) 0.24 (6.0) 0.18 (4.6) 0.50 (12.7) 0.44 (11.7) 0.042 (1.07) 0.038 (0.97) DIA. 1.25 (31.8) MIN. 0.310 (7.62) 0.290 (7.36) Dimensions in inches and (millimeters) NOTES: (1) Corrosion resistant terminals designed with 0.25” female quick connectors for wrap or snap-on (2) A thin film of silicone thermal compound is recommended between the bridge case and mounting surface for improved thermal conduction http://www.yeashin.com 4 REV.02 20110725