C400 mSATA NAND Flash SSD Features C400 mSATA NAND Flash SSD MTFDDAT128MAM, MTFDDAT256MAM Features • • • • • • • • • • • • Reliability – MTTF: 1.2 million device hours3 – Static and dynamic wear leveling – Uncorrectable bit error rate (UBER): <1 sector per 1015 bits read • Low power consumption – <200mW TYP 4 • Endurance: Total bytes written (TBW) – 72TB • Capacity5 (unformatted): 128GB, 256GB • Mechanical – 5mm height – mSATA connector: 3.3V ±5% – Caseless design: 50.80mm x 29.85mm x 3.75mm – Weight: 10g (MAX) • Field-updateable firmware • Operating temperature – Commercial (0°C to +70°C)6 Micron® 25nm MLC NAND Flash RoHS-compliant package SATA 6 Gb/s interface ATA modes supported – PIO mode 3, 4 – Multiword DMA mode 0, 1, 2 – Ultra DMA mode 0, 1, 2, 3, 4, 5 Industry-standard, 512-byte sector size support Native command queuing support with 32-command slot support ATA-8 ACS2 command set compliant ATA security feature command set and password login support Secure erase (data page) command set: fast and secure erase Self-monitoring, analysis, and reporting technology (SMART) command set Performance1, 2 – Sequential 128k READ: up to 500 MB/s – Sequential 128k WRITE: up to 260 MB/s – Random 4k READ: up to 45,000 IOPS – Random 4k WRITE: up to 50,000 IOPS – PCMark® Vantage (HDD test suite score): up to 75,000 – READ/WRITE latency: 55µs (TYP) Notes: 1. Typical I/O performance numbers as measured using Iometer with a queue depth of 32 and write cache enabled. 2. 4K transfers used for READ/WRITE latency values. 3. The product achieves a mean time to failure (MTTF) based on population statistics not relevant to individual units. 4. Active power measured during execution of MobileMark® 2007 with DIPM (device-initiated power management) enabled. 5. 1GB = 1 billion bytes; formatted capacity is less. 6. Drive case temperature. Warranty: Contact your Micron sales representative for further information regarding the product, including product warranties. PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 1 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. Products and specifications discussed herein are subject to change by Micron without notice. C400 mSATA NAND Flash SSD Features Part Numbering Information Micron’s RealSSD™ C400 SSD is available in different configurations and densities. Visit www.micron.com for a list of valid part numbers. Figure 1: Part Number Chart MT FD D AT xxx M AM - 1 K x x xx ES Production Status Micron Technology Blank = Production Product Family ES = Engineering sample FD = Flash drive Operating Temperature Range Drive Interface Blank = Commercial (0°C to +70°C) D = SATA 6.0 Gb/s Hardware Feature Set Drive Form Factor Blank = Null AT = mSATA AA = Contact factory AB = Contact factory Drive Density AC = Contact factory 128 = 128GB Firmware Feature Set 256 = 256GB Blank = Null NAND Flash Type 1 = Contact factory M = MLC 2 = Contact factory Product Family BOM Revision AM = C400 For example: 1 = 1st generation Sector Size NAND Flash Component 1 = 512-byte J = 32Gb, MLC, x8, 3.3V (25nm) K = 64Gb, MLC, x8, 3.3V (25nm) PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 2 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD General Description General Description Micron’s RealSSD solid state drive (SSD) uses a single-chip controller with a SATA interface on the system side and n-channels of Micron NAND Flash internally. Packaged in an JEDEC-standard mSATA form factor, the SSD integrates easily in existing storage infrastructures. The SSD is designed to use the SATA interface efficiently during both READs and WRITEs while delivering bandwidth-focused performance. SSD technology enables enhanced boot times, faster application load times, reduced power consumption, and extended reliability. Figure 2: Functional Block Diagram NAND SATA SSD controller NAND NAND NAND NAND DRAM buffer PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 3 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Logical Block Address Configuration Logical Block Address Configuration The drive is set to report the number of logical block addresses (LBA) that will ensure sufficient storage space for the specified density. Standard LBA settings, based on the IDEMA standard (LBA1-02), are shown below. Table 1: Standard LBA Settings Total LBA Drive Size Max LBA User Available Bytes Decimal Hexadecimal Decimal Hexadecimal (Unformatted) 128GB 250,069,680 EE7C2B0 250,069,679 EE7C2AF 128,035,676,160 256GB 500,118,192 1DCF32B0 500,118,191 1DCF32AF 256,186,209,271 Physical Configuration Table 2: mSATA Dimensions and Weight Value Unit Width 29.85 mm (NOM) Length 50.80 mm (NOM) 10 g (MAX) 3.75 mm (MAX) Unit weight Height PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 4 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Interface Connectors Interface Connectors Figure 3: SSD Interface Connections Primary side P1 P17 P15 Secondary side P51 P52 P18 P2 P16 Table 3: Signal Assignments Primary Side Secondary Side Pin # Signal Name Pin # Signal Name 1 Reserved Description No connect 2 3V3 Description +3.3V 3 Reserved No connect 4 GND Ground 5 Reserved No connect 6 1V5 No connect 7 Reserved No connect 8 Reserved No connect 9 GND Ground 10 Reserved No connect 11 Reserved No connect 12 Reserved No connect 13 Reserved No connect 14 Reserved No connect No connect 15 GND Ground 16 Reserved 17 Reserved No connect 18 GND 19 Reserved No connect 20 Reserved No connect 21 GND Ground 22 Reserved No connect Differential signal pair +B and -B 24 3V3 +3.3V 26 GND Ground Ground 23 +B 25 -B 27 GND Ground 28 1V5 No connect 29 GND Ground 30 TWI Two-wire interface Differential signal pair +A and -A 32 TWI 34 GND 31 -A 33 +A 35 GND Ground 36 Reserved No connect 37 GND Ground 38 Reserved No connect 39 3V3 +3.3V 40 GND 41 3V3 +3.3V 42 Reserved No connect 43 NC No connect 44 Reserved No connect 45 Optional No connect 46 Reserved No connect 47 Optional No connect 48 1V5 No connect 49 DA/DSS Drive activity LED 50 GND Ground 51 Presence Presence detection 52 3V3 +3.3V PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 5 Ground Ground Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Performance Performance Measured performance can vary for a number of reasons. The major factors affecting drive performance are the density of the drive and the interface of the host. Additionally, overall system performance can affect the measured drive performance. When comparing drives, it is recommended that all system variables are the same, and only the drive being tested varies. Performance numbers will vary depending on the host system configuration. Table 4: Drive Performance Notes: PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN Density 128GB 256GB Interface Speed 6 Gb/s 6 Gb/s Unit Sequential read (128k transfer) 500 500 MB/s Sequential write (128k transfer) 175 260 MB/s Random read (4k transfer) 45,000 45,000 IOPS Random write (4k transfer) 35,000 50,000 IOPS Read latency 55 55 µs Write latency 55 55 µs PCMark vantage 65,000 75,000 HDD score 1. Typical I/O performance numbers as measured using IOMeter with a queue depth of 32 and write cache enabled. 2. IOMeter measurements are performed on an 8GB span. 3. 4k transfers used for READ/WRITE latency values. 4. System variations may affect measured results. 5. Performance numbers are indicative of C400 firmware version 0009 and newer. 6 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Reliability Reliability Micron’s SSDs incorporate advanced technology for defect and error management. They use various combinations of hardware-based error correction algorithms and firmware-based static and dynamic wear-leveling algorithms. Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is defined as data that is reported as successfully programmed to the SSD but when it is read out of the SSD, the data differs from what was programmed. Table 5: Uncorrectable Bit Error Rate Uncorrectable Bit Error Rate Operation 1015 READ <1 sector per bits read Mean Time to Failure Mean time to failure (MTTF) for the SSD can be predicted based on the component reliability data using the methods referenced in the Telcordia SR-332 reliability prediction procedures for electronic equipment. Table 6: MTTF MTTF (Operating Hours)1 Density Note: 128GB 1.2 million 256GB 1.2 million 1. The product achieves a mean time to failure (MTTF) of 1.2 million hours, based on population statistics not relevant to individual units. Endurance Endurance for the SSD can be predicted based on the usage conditions applied to the device, the internal NAND component cycles, the write amplification factor, and the wear-leveling efficiency of the drive. The table below shows the drive lifetime for each SSD density based on predefined usage conditions. Table 7: Drive Lifetime Density Notes: PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN Drive Lifetime (Total Bytes Written) 128GB 72TB 256GB 72TB 1. Total bytes written calculated with the drive 90% full. 2. Access patterns are 50% sequential and 50% random and consist of the following: 5% are 4k; 5% are 8k; 10% are 16k; 10% are 32k; 35% are 64K; and 35% are 128k. 3. GB/day can be calculated by dividing the total bytes written value by (365 × number of years). For example: 72 TB/5 years/365 days = 40 GB/day for 5 years. 7 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Electrical Characteristics Electrical Characteristics Stresses greater than those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Table 8: mSATA Power Consumption Density Sequential Write/Read Maximum (128k transfer) Idle Average Active Average 128GB <85 150 3500 2000 mW 256GB <85 160 4000 2200 mW Notes: 1. 2. 3. 4. Unit Data taken at 25°C using a 6 Gb/s SATA interface. Active average power measured while running MobileMark® 2007 Productivity Suite. DIPM (device-initiated power management) enabled. Sequential power measured in IOMETER MAX with 128KB transfer size. Table 9: Maximum Ratings Parameter/Condition Symbol Min Max Unit 3V3 3.14 3.46 V TC 0 70 °C Non-operating temperature –40 85 °C Rate of temperature change – 20 °C/hour Relative humidity (non-condensing) 5 95 % Voltage input Operating temperature Notes: 1. Temperature is best measured with a thermocouple attached to the center point of the drive controller ASIC package. This is the larger package closest to the interface connector on the primary side. Refer to Package Dimensions for details. 2. Supply voltage slew rate during asynchronous power-down should follow a slope of no steeper than 60 mV/ms. 3. Power-off sequence: When the Micron C400 SSD is shut down, the ATA STANDBY IMMEDIATE (STBI) command should be the last command sent by the host and acknowledged by the SSD. Failure to follow this process could result in a longer than normal time-toready (TTR) during the subsequent power-on sequence. TTR is the time from power-on to drive ready to accept SATA commands. Table 10: Shock and Vibration Parameter/Condition Specification Operating shock 1500 G/1.0ms Operating vibration PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 2–500Hz at 3.1G 8 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Device ID Table 11: Identity Device See Note 1 for setting definitions Word Bit(s) Setting Default Value 0 Description General configuration bit-significant information 15 F 0b 0 = ATA device 14–8 X 0000100b 7 F 0b 1 = removable media device Obsolete Retired 6 F 1b 5–3 X 000b 2 V 0b Response incomplete 1 X 0b Retired 0 F 1 Retired 0b Reserved 3FFFh Obsolete 2 F C837h Specific configuration 3 F 0010h Obsolete 4 F 0000h 0000h 6 F 003Fh 7 (O)V 0000h 0000h 9 ( )X 0000h Retired 10 (M)F varies Serial number (20 ASCII characters) 20 ( )X 0000h 0000h 0000h 23 (M)F varies Firmware revision (8 ASCII characters) 27 (M)F varies Model number (40 ASCII characters) 15–8 F 80h 80h 7–0 F 10h 00h = Reserved 01h-FFh = Maximum number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands 47 48 Retired Obsolete Reserved for assignment by the CompactFlash™ Association Retired/Obsolete Trusted Computing feature set options 15 F 14 F 13–1 F 0 F PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 0b Shall be cleared to zero 1b Shall be set to one 0000000000000b Reserved for the Trusted Computing Group 0b 1=Trusted Computing feature set is support 9 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 49 Description Capabilities 15–14 F 00b Reserved for the IDENTIFY PACKET DEVICE command. 13 F 1b 1 = Standby timer values as specified in this standard are supported 0 = Standby timer values shall be managed by the device 12 F 0b Reserved for the IDENTIFY PACKET DEVICE command. 11 F 1b 1= IORDY supported 10 F 1b 1 = IORDY may be disabled 1b 1 = LBA supported 1 = DMA supported. 0 = IORDY may be supported 9 8 F 1b 7–0 F 00000000b 50 Capabilities 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13–2 F 000000000000b Reserved 1 X 0b Obsolete 0 F 1b Shall be set to one to indicate a vendor specific standby timer value minimum. ( )X 0000h 0000h 51 53 Obsolete 15–3 F 2 F 1b 1 = the fields reported in word 88 are valid 0 = the fields reported in word 88 are not valid 1 F 1b 1 = the fields reported in words (70:64) are valid 0 = the fields reported in words (70:64) are not valid 0 X 1b Obsolete ()X 3FFFh 0010h 003Fh FC10h 00FBh Obsolete 15 F 0b 1 = The BLOCK ERASE EXT command is supported 14 F 0b 1 = The OVERWRITE EXT command is supported 13 F 0b 1 = The CRYPTO SCRAMBLE EXT command is supported 1 = The Sanitize feature set is supported 54 59 Retired 0000000000000b Reserved 12 F 0b 11–9 F 000b 8 V 1b 7–0 V 00000001b 60 PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN M(F) Reserved 1 = Multiple sector setting is valid xxh = Current setting for number of logical sectors that shall be transferred per DRQ data block on READ/WRITE MULTIPLE commands Varies by capacity Total number of user addressable logical sectors 10 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 62 63 64 Default Value Description ()X 0000h Obsolete 15–11 F 00000b Reserved 10 V 0b 1 = Multiword DMA mode 2 is selected 0 = Multiword DMA mode 2 is not selected 9 V 0b 1 = Multiword DMA mode 1 is selected 0 = Multiword DMA mode 1 is not selected 8 V 0b 1 = Multiword DMA mode 0 is selected 0 = Multiword DMA mode 0 is not selected 7–3 F 0000b 2 F 1b 1 = Multiword DMA mode 2 and below are supported 1 F 1b 1 = Multiword DMA mode 1 and below are supported 0 F 1b 1 = Multiword DMA mode 0 is supported 15–8 F 0 7–0 Reserved Reserved F 03h 65 F 0078h PIO modes supported Minimum Multiword DMA transfer cycle time per word Cycle time in nanoseconds 66 F 0078h Manufacturer's recommended Multiword DMA transfer cycle time Cycle time in nanoseconds 67 F 0078h Minimum PIO transfer cycle time without flow control Cycle time in nanoseconds 68 F 0078h Minimum PIO transfer cycle time with IORDY flow control Cycle time in nanoseconds 69 F Additional Supported 15 F 0b 1 = CFast Specification Support 14 F 1b 1 = Deterministic read after Trim is supported 13 F 0b 1 = Long Physical Sector Alignment Error Reporting Control is supported 12 F 0b 1 = DEVICE CONFIGURATION IDENTIFY DMA and DEVICE CONFIGURATION SET DMA are supported 11 F 0b 1 = READ BUFFER DMA is supported 10 F 0b 1 = WRITE BUFFER DMA is supported 9 F 0b 1 = SET MAX PASSWORD DMA and SET MAX UNLOCK DMA are supported 8 F 0b 1 = DOWNLOAD MICROCODE DMA is supported 7 F 0b Reserved for IEEE-1667 6 F 0b 1 = Optional ATA device 28-bit commands supported 5 F 0b 1 = Read zero after Trim is supported 4–0 F 00000b Reserved F 0000h Reserved 70 PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 71 F Default Value 0000h 0000h 0000h 0000h 75 Description Reserved for the IDENTIFY PACKET DEVICE command Queue depth 15–5 F 00000000000b 4–0 F 11111b 76 Reserved Maximum queue depth - 1 Serial ATA Capabilities 15–13 F 000b Reserved 12 F 1b Supports Native Command Queuing priority information 11 F 0b Supports Unload while NCQ commands outstanding 10 F 1b Supports Phy event counters 9 F 1b Supports receipt of host initiated interface power management requests NOTE: HIPM is disabled (bit 9 = 0) for firmware versions 000G and newer Supports native Command Queueing 8 F 1b 7–4 F 0000b 3 F 1b 1 = Supports Serial ATA Gen-3 speed (6.0 Gb/s) 2 F 1b 1 = Supports Serial ATA Gen-2 speed (3.0 Gb/s) 1 F 1b 1 = Supports Serial ATA Gen-1 speed (1.5 Gb/s) 0 F 0b Reserved (set to 0) 77 Reserved for future Serial ATA signaling speed grades Serial ATA Additional capabilities 15–6 F 0000000000b 5 F 0b Supports NCQ Queue Management Command 4 F 0b Supports NCQ Streaming 3–1 V 010b 0 F 0b 15–7 F 000000000b 6 F 1b 1 = supports software settings preservation 5 F 0b Reserved 4 F 0b 1 = supports in-order data delivery 3 F 1b 1 = supports dev initiate interface power management 2 F 1b 1 = supports DMA Setup Auto-Activate optimization 1 F 0b 1 = supports non-zero buffer offsets in DMA Setup FIS 0 F 0b Reserved (set to 0) 78 Reserved for future Serial ATA definition Coded value indicating current negotiated Serial ATA signal speed Shall be cleared to zero Serial ATA features Supported PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN Reserved 12 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 79 Description Serial ATA features Enabled 15–7 V 000000000b 6 V 1b 1 = software settings preservation enabled 5 V 0b 1 = Asynchronous notification enabled 4 V 0b 1 = in-order data delivery enabled 3 V 0b 1 = device initiating interface power management enabled 2 V 0b 1 = DMA Setup Auto-Activate optimization enabled 1 V 0b 1 = non-zero buffer offsets in DMA Setup FIS enabled 0 V 0b Reserved (set to 0) 80 Reserved Major revision number 15–10 F 000000b 9 F 1b 1 = supports ATA8-ACS2 8 F 1b 1 = supports ATA8-ACS 7 F 1b 1 = supports ATA/ATAPI-7 6 F 1b 1 = supports ATA/ATAPI-6 5 F 1b 1 = supports ATA/ATAPI-5 4 F 1b 1 = supports ATA/ATAPI-4 3 F 1b Obsolete 2 S 0b Obsolete 1 S 0b Obsolete 0 F 0b Reserved F 0028h 81 Reserved Minor revision number 0028h = ATA8-ACS version 6 PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 82 Description Command set supported 15 X 0b Obsolete 14 F 1b 1 = NOP command supported 13 F 1b 1 = READ BUFFER command supported 12 F 1b 1 = WRITE BUFFER command supported 11 X 0b Obsolete 10 F 1b 1 = Host Protected Area feature set supported 9 F 0b 1 = DEVICE RESET command supported 8 F 0b 1 = SERVICE interrupt supported 7 F 0b 1 = release interrupt supported 6 F 1b 1 = read look-ahead supported 5 F 1b 1 = write cache supported 4 F 0b Shall be cleared to zero to indicate that the PACKET feature set is not supported. 3 F 1b 1 = mandatory Power Management feature set supported 2 F 0b Obsolete 1 F 1b 1 = Security feature set supported 0 F 1b 1 = SMART feature set supported 83 Command set supported 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = FLUSH CACHE EXT command supported 12 F 1b 1 = mandatory FLUSH CACHE command supported 11 F 1b 1 = Device Configuration Overlay feature set supported 10 F 1b 1 = 48-bit Address feature set supported 9 F 0b 1 = Automatic Acoustic Management feature set supported 8 F 1b 1 = SET MAX security extension supported 7 F 0b See Address Offset Reserved Area Boot INCITS TR27:2001 6 F 0b 1 = SET FEATURES subcommand required to spin-up after power-up 5 F 0b 1 = Power-Up In Standby feature set supported 4 F 0b Obsolete 3 F 1b 1 = Advanced Power Management feature set supported 2 F 0b 1 = CFA feature set supported 1 F 0b 1 = READ/WRITE DMA QUEUED supported 0 F 1b 1 = DOWNLOAD MICROCODE command supported PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 84 Description Command set/feature supported extension 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported 12 F 0b Reserved for technical report INCITS TR-37-2004 (TLC) 11 F 0b Reserved for technical report INCITS TR-37-2004 (TLC) 10–9 F 00b Obsolete 8 F 1b 1 = 64-bit Word wide name supported 7 F 0b 1 = WRITE DMA QUEUED FUA EXT command supported 6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands supported 5 F 1b 1 = General Purpose Logging feature set supported 4 F 0b 1 = Streaming feature set supported 3 F 0b 1 = Media Card Pass Through Command feature set supported 2 F 0b 1 = Media serial number supported 1 F 1b 1 = SMART self-test supported 0 F 1b 1 = SMART error logging supported 85 Command set/feature enabled. 15 X 0b Obsolete 14 F 1b 1 = NOP command supported 13 F 1b 1 = READ BUFFER command supported 12 F 1b 1 = WRITE BUFFER command supported 11 X 0b Obsolete 10 V 1b 1 = Host Protected Area feature set enabled 9 F 0b 1 = DEVICE RESET command supported 8 V 0b 1 = SERVICE interrupt enabled 7 V 0b 1 = release interrupt enabled 6 V 1b 1 = look-ahead enabled 5 V 1b 1 = write cache enabled 4 F 0b Shall be cleared to zero to indicate that the PACKET feature set is not supported. 3 F 1b Power Management feature set is enabled 2 F 0b Obsolete 1 V 0b 1 = Security Mode feature set enabled 0 V 1b 1 = SMART feature set enabled PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 86 Description Command set/feature enabled. 15 1b 1 = Words 120-119 are valid 14 F 0b 1 = Reserved 13 F 1b 1 = FLUSH CACHE EXT command supported 12 F 1b 1 = FLUSH CACHE command supported 11 F 1b 1 = Device Configuration Overlay supported 10 F 1b 1 = 48-bit Address features set supported 9 V 0b 1 = Automatic Acoustic Management feature set enabled 8 F 0b 1 = SET MAX security enabled by SET MAX SET PASSWORD 7 F 0b Reserved for address Offset Reserved Area Boot, INCITS TR27:2001 6 F 0b 1 = SET FEATURES subcommand required to spin-up after power-up 5 V 0b 1 = Power-Up In Standby feature set enabled 4 V 0b Obsolete 3 V 1b 1 = Advanced Power Management feature set enabled 2 F 0b 1 = CFA feature set supported 1 F 0b 1 = READ/WRITE DMA QUEUED command supported 0 F 1b 1 = DOWNLOAD MICROCODE command supported 87 Command set/feature enabled/supported 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 1b 1 = IDLE IMMEDIATE with UNLOAD FEATURE supported 12 V 0b Reserved for technical report- INCITS tr-37-2004 (TLC) 11 V 0b Reserved for technical report- INCITS TR-37-2004 (TLC) 10–9 F 00b Obsolete 8 F 1b 1 = 64-bit Word wide name supported 7 F 0b 1 = WRITE DMA QUEUED FUA EXT command supported 6 F 1b 1 = WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands supported 5 F 1b 1 = General Purpose Logging feature set supported 4 V 0b Obsolete 3 V 0b 1 = Media Card Pass Through Command feature set supported 2 V 0b 1 = Media serial number is valid 1 F 1b 1 = SMART self-test supported 0 F 1b 1 = SMART error logging supported PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting 88 Default Value Description 0b Ultra DMA modes 15 0b Reserved 14 0b 1 = Ultra DMA mode 6 is selected 0 = Ultra DMA mode 6 is not selected 13 0b 1 = Ultra DMA mode 5 is selected 0 = Ultra DMA mode 5 is not selected 12 0b 1 = Ultra DMA mode 4 is selected 0 = Ultra DMA mode 4 is not selected 11 0b 1 = Ultra DMA mode 3 is selected 0 = Ultra DMA mode 3 is not selected 10 0b 1 = Ultra DMA mode 2 is selected 0 = Ultra DMA mode 2 is not selected 9 0b 1 = Ultra DMA mode 1 is selected 0 = Ultra DMA mode 1 is not selected 8 0b 1 = Ultra DMA mode 0 is selected 0 = Ultra DMA mode 0 is not selected 7 0b Reserved 6 0b 1 = Ultra DMA mode 6 and below are supported 5 1b 1 = Ultra DMA mode 5 and below are supported 4 1b 1 = Ultra DMA mode 4 and below are supported 3 1b 1 = Ultra DMA mode 3 and below are supported 2 1b 1 = Ultra DMA mode 2 and below are supported 1 1b 1 = Ultra DMA mode 1 and below are supported 0 1b 1 = Ultra DMA mode 0 IS supported 89 (O)F 0001h Time required for security erase unit completion 90 (O)F 0001h Time required for Enhanced security erase completion 91 (O)V 00FEh Current advanced power management value 92 (O)V FFFEh Master Password Revision Code PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 93 Description Shall be 0000h for SATA devices 15 0b Shall be cleared to zero 14 0b Shall be set to one 13 0b 1 = device detected CBLID-above VIH 0 = device detected CBLID-below VIL Device 1 hardware reset result Device 0 shall clear these bits to zero Device 1 shall set these bits as follows: 12 0b Reserved 11 0b 0 = Device 1 did not assert PDIAG1 = Device 1 asserted PDIAG- 10–9 These bits indicate how Device 1 determined the device number: 00 = Reserved 01 = a jumper was used 10 = the CSEL signal was used 11 = some other method was used or the method is unknown 8 0b Shall be set to one Device 0 hardware reset result. Device 1 shall clear these bits to zero. Device 0 shall set these bits as follows: 94 7 0b Reserved 6 0b 0 = Device 0 does not respond when Device 1 is selected. 1 = Device 0 responds when Device 1 is selected. 5 0b 0 = Device 0 did not detect the assertion of DASP1 = Device 0 detected the assertion of DASP- 4 0b 0 = Device 0 did not detect the assertion of PDIAG1 = Device 0 detected the assertion of PDIAG- 3 0b 0 = Device 0 failed diagnostics. 1 = Device 0 passed diagnostics. 2–1 00b These bits indicate how Device 0 determined the device number: 00 = Reserved 01 = a jumper was used 10 = the CSEL signal was used 11 = some other method was used or the method is unknown 0 0b Shall be set to one 00h Vendor's recommended acoustic management value V 00h Current automatic acoustic management value (O)V 0000h 15–8 7–0 95 PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN F Stream Minimum Request Size 18 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value Description 96 (O)V 0000h Streaming Transfer Time - DMA 97 (O)V 0000h Streaming Access Latency - DMA and PIO 98 (O)F 100 V 0000h 0000h 104 (O)V 0000h Streaming Transfer Time - PIO 105 ( )F 0008h Maximum number of 512-byte blocks of LBA Range Entries per DATA SET MANAGEMENT command 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13 F 0b 1 = Device has multiple logical sectors per physical sector 1 = Device Logical Sector Longer than 256 Words 106 Physical sector size / Logical Sector Size 12 F 0b 11–4 F 00000000b 3–0 F 0000b 2^x logical sectors per physical sector (O)F 0000h Inter-seek delay for ISO-7779 acoustic testing in microseconds 0101b NAA (3-0) 107 108 15–12 F 11–0 109 Streaming Performance Granularity(98-99) Varies by capacity Maximum user LBA for 48-bit Address feature set 15–4 F 3–0 Reserved 000000001010b IEEE OUI (23-12) 000001110101b IEEE OUI (11-0) Varies Unique ID (35-32) 110 (M)F Varies 5-0 Unique ID (31-16) 111 (M)F Varies Unique ID (15-0) 112 (O)F 0000h 0000h 0000h 0000h 116 (O)V 0000h 117 (O)F 0000h 0000h PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN Reserved for 128 bit world wide name extension to 128 bits Reserved for INCITS TR-37-2004 Words per Logical Sector 19 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 119 Description Commands and feature sets supported (Continued from words 84-82) 15 F 0b Shall be cleared to zero Shall be set to one 14 F 1b 13–6 F 00000001b 5 F 0b 1 = Free-fall Control feature set is supported 4 F 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is supported 3 F 1b 1 = READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported 2 F 1b 1 = The Write-Read-Verify feature set is supported 1 F 1b 1 = Feature set "Disable Data Transfer After Error Detection" is supported 0 F 0b Reserved for DDT 120 Reserved Commands and feature sets supported or enabled (Continued from words 87-85) 15 0b Shall be cleared to zero 14 1b Shall be set to one 13–6 00000000b 5 0b 1 = Free-fall Control feature set is enabled 4 1b 1 = The DOWNLOAD MICROCODE command with mode 3 is supported 3 1b 1 = The READ LOG DMA EXT and WRITE LOG DMA EXT commands are supported 2 1b 1 = The WRITE UNCORRECTABLE EXT command is supported 1 0b 1 = The Write-Read-Verify feature set is enabled 0 0b 1= Feature set "Disable Data Transfer After Error Detection" is enabled 0 = Feature set "Disable Data Transfer After Error Detection" is disabled 121 F 0000h 0000h 0000h 0000h 0000h 0000h 127 (O) 0000h PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN Reserved Reserved for expanded supported and enabled settings Obsolete 20 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 128 Security status 15–9 F 0000000b Reserved 8 V 0b Security level 0 = High, 1 = Maximum 7–6 F 00b Reserved 5 F 1b 1 = Enhanced security erase supported 4 V 0b 1 = Security count expired 3 V 0b 1 = Security frozen 2 V 0b 1 = Security locked 1 V 0b 1 = Security enabled 0 F 1b 1 = Security supported ( )X Vendor specific data 129 160 Vendor specific CFA power mode 1 15 F 0b Word 160 supported 14 F 0b Reserved 13 F 0b CFA power mode 1 is required for one or more commands implemented by the device 12 V 0b CFA power mode 1 disabled 11–0 F 000000000000b X 0000h 0000h 0000h 0000h 0000h 0000h 0000h 15–4 F 000h 3-0 F 5h 161 168 Description 169 Maximum current in ma Reserved for assignment by the CompactFlash Association Reserved Device Nominal Form Factor DATA SET MANAGEMENT command support 15–1 F 0 F 1b 170 F 0000h 0000h 0000h 0000h Additional Product Identifier 174 F 0000h 0000h Reserved 176 (O)V Varies PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 000000000000000 Reserved b 1 = the Trim bit in the DATA SET MANAGEMENT command is supported Current media serial number (60 ASCII characters) 21 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 206 Description SCT Command Transport 15–12 X 0000b 11–6 F 000000b 5 F 1b SCT Command Transport Data Tables supported 4 F 1b CT Command Transport Features Control supported 3 F 1b SCT Command Transport Error Recovery Control supported 2 F 1b SCT Command Transport Write Same supported 1 F 0b SCT Command Transport Long Sector Access supported 0 F 1b SCT Command Transport supported ( )F 0000h 0000h 207 209 (O) Vendor Specific Reserved Reserved for CE-ATA Alignment of logical blocks within a larger physical block 15 F 0b Shall be cleared to zero 14 F 1b Shall be set to one 13–0 F 00000000000000b 'Logical sector' offset within the first physical sector where the first logical sector is placed. 210 (O)V 0000h 0000h Write-Read-Verify Sector Count Mode 3 Only 212 (O)F 0000h 0001h Verify Sector Count Mode 2 Only 214 (O) NV Cache Capabilities 15–12 F 0000b NV Cache feature set version 11–8 F 0000b NV Cache Power Mode feature set version 7–5 F 000b Reserved 4 V 0b 1 = NV Cache feature set enabled 3–2 F 00b Reserved 1 V 0b 1 = NV Cache Power Mode feature set enabled 0 F 0b 1 = NV Cache Power Mode feature set supported 215 (O)V 0000h NV Cache Size in Logical Blocks (LSW) 216 (O)V 0000h NV Cache Size in Logical Blocks (MSW) 217 (M)F 0001h Nominal media rotation rate (ATA8-ACS 1699-D Revision 6) NV Cache Read Transfer Speed in MB/s (ATA8-ACS 1699-D Revision 3f) 218 (O)V 0000h 15–8 F 00h Reserved 7–0 F 00h Device Estimated Time to Spin Up in Seconds 15–8 F 00h Reserved 7–0 V 00h Write-Read-Verify feature set current mode 219 220 NV Cache Write Transfer Speed in MB/s NV Cache Options 221 PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 0000h Reserved 22 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Device ID Table 11: Identity Device (Continued) See Note 1 for setting definitions Word Bit(s) Setting Default Value 222 Description Transport Major revision number. 0000h or FFFFh = device does not report version 15–12 0001b Transport Type - 0 = Parallel, 1 = Serial, 2-15 = Reserved Parallel (Type = 0) Serial (Type = 1) 11–6 000000b 5 1b Reserved SATA Rev 3.0 4 1b Reserved SATA Rev 2.6 3 1b Reserved SATA Rev 2.5 2 1b Reserved SATA II: Extensions 1 1b Reserved SATA 1.0a 0 1b ATA8-APT ATA8-AST Reserved Reserved 223 (M)F 0000h 224 ( )F 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 234 (O)F 0001h Minimum number of 512 byte units per DOWNLOAD MICROCODE command for mode 3 235 00FFh Maximum number of 512 byte units per DOWNLOAD MICROCODE command for mode 3 236 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 0000h 255 (M)F Transport Minor revision number Reserved for CE-ATA Reserved Integrity word 15–8 varies Checksum 7–0 A5h Signature Note: PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 1. F = The content of the word is fixed and does not change. V = The content of the word is variable and may change depending on the state of the device or the commands executed by the device. X = The content of the word may be fixed or variable. R = The content of the word is reserved and will be zero. 23 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Commands Commands Table 12: Supported ATA Command Set See ATA-8 standard for command details Command Name Command Code (hex) CHECK POWER MODE 98h or E5h DEVICE CONFIGURATION RESTORE B1h/C1h DEVICE CONFIGURATION FREEZE LOCK B1h/C3h DEVICE CONFIGURATION IDENTIFY B1h/C1h DEVICE CONFIGURATION SET B1h/C3h DOWNLOAD MICROCODE 92h EXECUTE DEVICE DIAGNOSTIC 90h FLUSH CACHE E7h FLUSH CACHE EXT EAh IDENTIFY DEVICE ECh IDLE E3h or 97h IDLE IMMEDIATE E1h or 95h INITIALIZE DEVICE PARAMETERS 91h NOP 00h READ BUFFER E4h READ DMA (with retry) C8h READ DMA (without retry) C9h READ DMA EXT 25h READ FPDMA QUEUED 60h READ LOG EXT 2Fh READ MULTIPLE C4h READ MULTIPLE EXT 29h READ NATIVE MAX ADDRESS F8h READ NATIVE MAX ADDRESS EXT 27h READ SECTOR(S) EXT 24h READ SECTOR(S) (with retry) 20h READ SECTOR(S) (without retry) 21h READ VERIFY SECTOR EXT 42h READ VERIFY SECTOR(S) (with retry) 40h SCT WRITE SAME 02h/0001h 02h/0002h 02h/0101h 02h/0102h SCT RETURN ERROR RECOVERY CONTROL 030h/01h SCT SET ERROR RECOVERY CONTROL 03h/01h SCT SET FEATURE CONTROL 04h/01h SCT RETURN FEATURE CONTROL 04h/02h PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Commands Table 12: Supported ATA Command Set (Continued) See ATA-8 standard for command details Command Name Command Code (hex) SCT RETURN FEATURE OPTION FLAG 04h/03h SCT RETURN SCT DATA TABLE 05h/01h SECURITY DISABLE PASSWORD F6h SECURITY ERASE PREPARE F3h SECURITY ERASE UNIT F4h SECURITY FREEZE LOCK F5h SECURITY SET PASSWORD F1h SECURITY UNLOCK F2h SEEK 7xh SET FEATURES EFh SET MAX ADDRESS F9h SET MAX – FREEZE LOCK F9h/04h SET MAX – LOCK F9h/02h SET MAX ADDRESS EXT 37h SET MULTIPLE MODE C6h SET MAX – SET PASSWORD F9h/01h SET MAX – UNLOCK F9h/03h SLEEP E6h or 99h SMART DISABLE OPERATIONS B0h/D9h SMART ENABLE OPERATIONS B0h/D8h SMART ENABLE/DISABLE AUTOSAVE B0h/D2h SMART EXECUTE OFF-LINE IMMEDIATE B0h/D4h SMART READ DATA B0h/D0h SMART READ LOG SECTOR B0h/D5h SMART RETURN STATUS B0h/DAh SMART WRITE LOG B0h/D6h STANDBY E2h or 96h STANDBY IMMEDIATE E0h or 94h WRITE BUFFER E8h WRITE DMA (with retry) CAh WRITE DMA (without retry) CBh WRITE DMA EXT 35h WRITE DMA FUA EXT 3Dh WRITE FPDMA QUEUED 61h WRITE LOG EXT 3Fh WRITE MULTIPLE C5h WRITE MULTIPLE EXT 39h PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Commands Table 12: Supported ATA Command Set (Continued) See ATA-8 standard for command details Command Name Command Code (hex) WRITE MULTIPLE FUA EXT CEh WRITE SECTOR(S) (with retry) 30h WRITE SECTOR(S) EXT 34h WRITE UNCORRECTABLE EXT 45h PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 26 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Compliance Compliance Micron SSDs comply with the following: • • • • • • • • • • • RoHS “green” CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003 FCC: CFR Title 47, Part 15, ICES-003, all Class B UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Edition BSMI (Taiwan): approval to CNS 13438 C-TICK (Australia, New Zealand): approval to AS/NZS CISPR22 KCC RRL (Korea): approval to KCC MU2-C30025, KCC MU2-C30018 Class B W.E.E.E.: Compliance with EU WEEE directive 2002/96/EC. Additional obligations may apply to customers who place these products in the markets where WEEE is enforced. TUV (Germany): approval to IEC60950/EN60950 VCCI IC (Canada): - This Class B digital apparatus complies with Canadian ICES-003. - Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FCC Rules This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 27 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Package Dimensions Package Dimensions Figure 4: mSATA Package – 50.80mm 2.60mm DIA THRU 0.102in (2 PLCS) 3.11mm 0.122in P1 0.75mm RAD 0.030in 3.75mm 0.148in 1.00mm RAD 0.039in (2 PLCS) 5.69mm 0.224in 1.40mm 0.055in 1.00mm 0.039in 1.35mm 0.053in 4.34mm 0.171in 3.53mm 0.139in (2 PLCS) 2.83mm 0.111in 2.08mm 0.082in 11.08mm 0.436in 29.85mm 1.175in 2.08mm 0.082in 2.83mm 0.111in PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 2.75mm 0.108in 5.27mm 0.207in 50.80mm 2.000in 28 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD References References • Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available at www.sata-io.org • SATA 3.0 GOLD • ATA-8 ACS2 • JEDEC MO-300B (mSATA SSD Assembly) PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved. C400 mSATA NAND Flash SSD Revision History Revision History Rev. D – 8/12 • • • • Changed MTBF to MTTF. Added new power-off sequence note to Maximum Ratings table. Updated note 3 (GB/day) under Drive Lifetime table. Added new note to Word 76 in Device ID table. Rev. C – 4/12 • In Features section, removed reference to hot-plug-capable and changed caseless design height from 3.80mm to 3.75mm. • In Physical Configuration section, changed height from 3.80mm to 3.75mm. • Updated package dimensions figure (mSATA Package – 50.80mm): – 3.80mm to 3.75mm – 0.150in to 0.148in – 1.40mm to 1.35mm – 0.055in to 0.053in Rev. B – 3/12 • Production status. Rev. A – 10/11 • Initial release. 8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900 www.micron.com/productsupport Customer Comment Line: 800-932-4992 Micron and the Micron logo are trademarks of Micron Technology, Inc. All other trademarks are the property of their respective owners. This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein. Although considered final, these specifications are subject to change, as further product development and data characterization sometimes occur. PDF: 09005aef8484bfff realssd_c400_msata.pdf - Rev. D 8/12 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice. © 2011 Micron Technology, Inc. All rights reserved.