P-DUKE DOS10-05T Point of load dc-dc converter Datasheet

DOS(H)10-05T SERIES
POINT OF LOAD
DC-DC CONVERTER
FEATURES
• OUTPUT CURRENT UP TO 10A
• SMALL SIZE AND LOW PROFILE :
1.30” X 0.53” X 0.30” (SMD) ; 2.00” X 0.50” X 0.28” (SIP)
• HIGH EFFICIENCY UP TO 95% @ 3.3V FULL LOAD
• INPUT RANGE FROM 2.4VDC TO 5.5VDC
• FIXED SWITCHING FREQUENCY (300kHZ)
• SMD & SIP PACKAGES
• SMD PACKAGE QUALIFIED FOR LEADFREE REFLOW SOLDER
PROCESS ACCORDING IPC J-STD-020D
• OUTPUT VOLTAGE PROGRAMMABLE FROM 0.75VDC TO 3.3VDC
VIA EXTERNAL RESISTOR
• INPUT UNDER-VOLTAGE PROTECTION
• UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS
• CE MARKED
• COMPLIANT TO RoHS II & REACH
APPLICATIONS
Wireless Network
Telecom/Datacom
Industry Control System
Distributed Power Architectures
Semiconductor Equipment
Microprocessor Power Applications
OPTIONS
POSITIVE LOGIC REMOTE ON/OFF
DESCRIPTION
DOS10-05T (SMD type), DOH10-05T (for Vertical Mounting SIP type) and
DOH10-05TA (for Horizontal Mounting SIP type) are non-isolated DC/DC
converters that can deliver up to 10A of output current with full load efficiency of
95% at 3.3V output.
T E C H N I C A L S P E C I F I C AT I O N
All specifications are typical at nominal input, full load and 25ºC otherwise noted
INPUT SPECIFICATIONS
OUTPUT SPECIFICATIONS
Output current
Voltage accuracy
Minimum load
Line regulation
Load regulation
Vin=Vout(set)+0.5V to Vin(max)
at Full Load
No Load to Full Load
Ripple and noise (Note2) 20MHz bandwidth
Temperature coefficient
ΔIo /Δt = 2.5A/µs ,Vin(nom)
Dynamic load
Load change step
response
(50% to 100% or
(Note 2)
100% to 50% of Io(max))
ΔIo /Δt = 2.5A/µs ,Vin(nom)
Dynamic load
Load change step
response
(50% to 100% or
(Note 3)
100% to 50% of Io(max)
Output current limit
10A max Input voltage range
± 2%Vout(set) Maximum input current
0%
Input filter (Note 5)
Vout(set) < Vin – 0.5V
Vin=2.4 to 5.5V; Io=Io(max)
Peak deviation
Setting time
(Vout<10%peak
deviation)
Peak deviation
Setting time
(Vout<10%peak
deviation)
200mV
25µs
Operating ambient temperature
Storage temperature range
100mV Thermal shock
100µs
Isolation voltage
Switching frequency
Safety approvals
SMD
Dimensions
SIP
Page 1 of 3
–55ºC ~ +125ºC
MIL-STD-810F
Relative humidity(non-condensing)
5% ~ 95% RH
IPC J-STD-020D
IPC J-STD-033B
Level 2a
125ºC
FEATURE SPECIFICATIONS
Remote ON/OFF(Note 6)
(Negative logic)(standard) ON = Open or 0V < Vr < 0.3V
OFF =1.5V < Vr < Vin(max)
See table
ON = Open or Vin(max)
None (Positive logic)(option)
OFF=0V < Vr < 0.3V
300kHz±10%
Input current of Remote control pin
IEC60950-1, UL60950-1, & EN60950-1
Remote off state input current Nominal Input
1.30 X 0.53 X 0.30 Inch
(33.0 X 13.5 X 7.7 mm) Remote sense range
2.00 X 0.50 X 0.28 Inch
(50.8 X 12.7 X 7.2 mm) Rise time Time for Vout to rise from 10% to 90%of Vout(set)
Weight
MTBF (Note 1)
–40ºC ~ +85ºC(with derating)
MIL-STD-810F
GENERAL SPECIFICATIONS
Efficiency
6.0g(0.22oz)
MIL-HDBK-217F
3.239 x 106 hrs
100mAp-p
Vibration
200%
0.7525V ~ 3.63V
100mA
130mA
2.2VDC
2.0VDC
ENVIRONMENTAL SPECIFICATIONS
Lead-free reflow solder process
Continuous, automatics recovery
ESR≧1mΩ
1000µF,max Moisture sensitivity level(MSL)
External load capacitance
5000µF,max
ESR≧10mΩ
Over temperature protection
Output voltage overshoot-startup Vin=2.4 ~ 5.5V, F.L.
1%Vout(set)
(Note 4)
10A
C filter
± 0.3%Vout(set) Input no load current
Vout(set) =0.75VDC
(Vin=5V, Io=0, module enabled)
Vout(set) =3.3VDC
± 0.4%Vout(set)
Start-up voltage
15mVrms,max Input under voltage lockout
Shutdown voltage
50mVp-p,max
Input reflected ripple current5~20MHz, 1µH source impedance
±0.4%
Output short-circuit current
Voltage adjustability (see fig.1)
2.4 ~ 5.5VDC
Turn-on delay time
www.pduke.com
IIN=10µA,max
IIN=1mA,max
IIN=10µA,max
IIN=1mA,max
10µA~1.0mA
1.5mA,typ
0.5V,max
6mS, max.
Case 1 (Note7)
Case 2 (Note8)
1ms
1ms
2014/4/30
DOS(H)10-05T SERIES
POINT OF LOAD
Model Name
ON/OFF
Logic
DOS10-05T
DOS10-05T-P
DOH10-05T
DOH10-05T-P
DOH10-05TA
DOH10-05TA-P
Negative
Positive
Negative
Positive
Negative
Positive
Package
Input Voltage
DC-DC CONVERTER
Output Voltage
Output Current
Efficiency (%)
Min. Load
Max. Load
5.0Vin,
3.3VDC@10A
0A
10A
95%
SMD
Vertical Mounting
2.4 ~ 5.5VDC
Vin(min)=Vout(set)+0.5V
SIP
Horizontal Mounting
SIP
0.75 ~ 3.3VDC
Note
1. MIL-HDBK-217F @Ta=25 ºC, Full load.
2. External with Cout = 1µF ceramic//10µF tantalum capacitors.
3. External with Cout = 2pcs of 150µF polymer capacitors.
4. Output voltage programmable from 0.75V to 3.3V by connecting a single resistor (shown as Rtrim in Table 1) between the TRIM and GND pins of the
module.To calculate the value of the resistor Rtrim for a particular output voltage Vout, use the following equation:
21070


Rtrim = 
- 5110 Ω
 Vout - 0.7525

5.
6.
7.
8.
It’s necessary to equip the external input capacitors at the input of the module. The capacitors should connect as close as possible to the input
terminals that ensuring module stability. The external Cin is 3pcs of 150µF low-ESR polymer capacitors // 2pcs of 47µF ceramic capacitors at least.
Device code with suffix “-P” – Positive logic(ON/OFF is open collector/drain logic input; Signal referenced to GND )
Device code with no suffix – Negative logic (ON/OFF pin is open collector/drain logic input with external pull –up resistor; signal referenced to GND)
Case 1 :On/Off input is set to logic low (module on) and then input power is applied (delay from instant at which Vin=Vin(min) until Vout=10% of Vout(set))
Case 2 :Input power is applied for at least one second and then the ON/OFF input is set to logic low (delay form instant at which Von/off=0.3V until
Vout=10% of Vout(set))
CAUTION: This power module is not internally fused. An input line fuse must always be used.
DOS10-05T, Vo=3.3V, Derating Curve
OUTPUT CURRENT,Io(A)
12
10
8
6
4
2
0
20
30
40
50
60
70
℃
80
90
AMBIENT TEMPERATURE,TA( )
Fig. 1
Table 1
Vout(set) (V) Rtrim (KΩ)
Page 2 of 3
www.pduke.com
0.7525
Open
1.2
41.973
1.5
23.077
1.8
15.004
2.5
6.974
3.3
3.160
2014/4/30
DOS(H)10-05T SERIES
POINT OF LOAD
MECHANICAL DRAWING
DC-DC CONVERTER
:
DOH10-05T TYPE
PIN CONNECTION
PIN
1
2
3
4
5
6
7
8
10
11
DEFINE
+OUTPUT
+OUTPUT
+SENSE
+OUTPUT
GND
GND
+ INPUT
+ INPUT
TRIM
CTRL
DOH10-05TA TYPE
PIN CONNECTION
PIN
1
2
3
4
5
6
7
8
10
11
DEFINE
+OUTPUT
+OUTPUT
+SENSE
+OUTPUT
GND
GND
+ INPUT
+ INPUT
TRIM
CTRL
DOS10-05T TYPE
PIN CONNECTION
PIN
1
2
3
4
5
6
DEFINE
CTRL
+SENSE
TRIM
+OUTPUT
GND
+ INPUT
1. All dimensions in Inch (mm)
Tolerance: X.XX±0.02 (X.X±0.5)
X.XXX±0.01 (X.XX±0.25)
2. Pin pitch tolerance ±0.01 (0.25)
3. Pin dimension tolerance ±0.004 (0.1)
Page 3 of 3
www.pduke.com
2014/4/30
Similar pages