OPB916 Series Features: Low power consumption Data rates to 250 kBaud Choice of two logic states and two electrical outputs 24” (610 mm) minimum 26 AWG UL listed wires Slot width 0.20” (5.08 mm) Slot Depth 0.635” (16.13 mm) Description: The OPB916 series of Photologic® photo integrated circuit switches provide optimum flexibility. Each switch consists of an infrared Light Emitting Diode (LED) and a Photologic® photo integrated circuit, mounted in an opaque housing with clear windows for dust protection. The deep slot allows for a longer reach of the optical path from the 0.650” (16.5 mm) mounting plane. Internal apertures are 0.010” x .060” (.25 mm x 1.52 mm) for the Photologic’s “S” side and 0.05” x 0.06” (1.27 mm x 1.52 mm) for the LED “E” side. Devices in this series exhibit stable performance over supply voltages ranging from 4.5 V to 16.0 V, and may be specified as buffered or inverted with an internal 10 kΩ pull-up resistor or open collector output. Devices are TTL/LSTTL compatible and can drive up to 10 TTL loads. Custom electrical, wire or cabling are available. Contact your local representative or OPTEK for more information. Ordering Information Applications: Mechanical switch replacement Speed indication (tachometer) Mechanical limit indication Edge sensing Part Number OPB916BZ OPB916IZ LED Peak Wavelength 880 nm Sensor Photologic® 10K Pull-Up Inv-10K Pull-Up OPB916BOCZ Open-Collector OPB916B 10K Pull-Up Color Description Red Anode Black Cathode White Vcc Blue Output Green Ground Slot Width / Depth Aperture Emitter / Sensor Lead Length / Wire 0.200” / 0.635” 0.05" / 0.01" 24" / 26 AWG Wire OPB916BOC Open-Collector Light ON output High Light ON output High OPB916I Inverted 10K Pull-Up OPB916IOC Inverted Open-Collector Light ON output Low Light ON output Low RoHS General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue B 10/2016 Page 1 Color-Pin # Description Red Anode Black Cathode Green Ground Blue Output White VCC Tolerence ±0.010 [0.254] DIMENSIONS ARE IN: [ MILLIMETERS] INCHES Absolute Maximum Ratings (TA = 25° C unless otherwise noted) Storage & Operating Temperature Range -40°C to +80°C Input Infrared LED Diode Reverse DC Voltage 2V Input Diode Power Dissipation(2) 75 mW Forward DC Current 50 mA Output Photologic® Supply Voltage, VCC (not to exceed 3 seconds) 18 V Voltage at Output Lead (Open Collector Output) 30 V Output Photologic® Power Dissipation(3) Notes: (1) (2) (3) (4) (5) 90 mW RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. Derate linearly 1.67 mW/°C above 25°. Derate linearly 2.67 mW/°C above 25°. Normal application would be with light source blocked, simulated by IF = 0 mA. All parameters tested using pulse technique. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue B 10/2016 Page 2 Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode VF Forward Voltage - 1.3 1.8 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2 V, TA = 25° C 4.5 - 16 V - Output Photologic® Sensor VCC Operating DC Supply Voltage - - 7 mA ICCL Low Level Supply Current: Buffered with 10k pull-up(1) Buffered Open-Collector Output(1) VCC = 16 V, IF = 0 mA, No Output Load Inverted with 10k pull-up: Inverted Open-Collector Output - - 7 mA VCC = 16 V, IF = 10 mA, No Output Load - - 6 mA VCC = 16 V, IF = 10 mA, No Output Load - - 6 mA VCC = 16 V, IF = 0 mA, No Output Load - - 0.4 V VCC = 4.5 V, IOL = 16 mA, IF = 0 mA - - 0.4 V VCC = 4.5 V, IOL = 16 mA, IF = 10 mA ICCH High Level Supply Current: Buffered with 10k pull-up Buffered Open-Collector Output Inverted with 10k pull-up: Inverted Open-Collector Output(1) VOL Low Level Output Voltage: Buffered with 10k pull-up Buffered Open-Collector Output Inverted with 10k pull-up: Inverted Open-Collector Output VOH High Level Output Voltage: Buffered with 10k pull-up Inverted with 10k pull-up: IOH - - V VCC2.0 - - V VCC = 4.5 V to 16 V, IF = 0 mA, - 1.0 10 µA VCC = 4.5 V, IF = 10 mA, VOH = 30 V - 1.0 10 µA VCC = 4.5 V, IF = 0 mA, VOH = 30 V High Level Output Current: Buffered with 10k pull-up Buffered Open-Collector Output Inverted with 10k pull-up: Inverted Open-Collector Output(1) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc . VCC = 4.5 V to 16 V, IF = 10 mA, IOH = 100 µA VCC2.0 OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue B 10/2016 Page 3 Electrical Characteristics (TA = 25° C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS - 5 10 mA VCC = 5 V, No Output Load - 5 10 mA VCC = 4.5 V, IOL = 16 mA Hysteresis - 1.5 - - t rtf Rise Time, Fall Time - 50 - ns tPLHtPHL Propagation Delay - 3 - µs Output Photologic® Sensor IF(+) LED Positive-Going Threshold Current Buffered with 10k pull-up Inverted with 10k pull-up Buffered Open-Collector Output Inverted Open-Collector Output(1) IF(+)/IF(-) VCC = 5 V VCC = 5 V, IF = 0 or 10 mA, RL = 300 Ω to 5 V, CL = 50 pF Notes: (1) Normal application would be with light source blocked, simulated by IF = 0 mA. (2) All parameters tested using pulse technique. General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue B 10/2016 Page 4 OPB916B - Flag Next to Emitter OPB916B - Flag Next to Sensor 1.20 1.20 1.00 1.00 Right to Left Right to Left (back) 0.80 0.80 Top to Bottom Bottom to Top 0.60 Top to Bottom Bottom to Top Logic Logic Right to Left Right to Left (back) Left to Right 0.60 Left to Right Left to Right (back) Left to Right (back) 0.40 0.40 0.20 0.20 0.00 0.00 0.05 0.10 0.15 0.20 0.25 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Displacement (inches) Displacement (inches) OPB916B - Flag in Middle of Slot 1.20 1.00 0 Right to Left Top to Bottom Right to Left (back) Logic 0.80 Top to Bottom Bottom to Top 0.60 Left to Right Emitter Left to Right (back) Left to Right 0.40 Right to Left Sensor 0.20 0 Width 0.00 0.00 0.05 0.10 0.15 0.20 0.25 Distance (inches) General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue B 10/2016 Page 5 Issue Change Description Approval Date A Initial Release, new format Steve Coble 12/13/06 A.1 Fixed Ordering Table page 1 Bob Procsal 1/25/08 A.2 Fixed nomenclature on schematics page 1 Mark Miller 8/04/08 A.3 Changed mechanical drawing, Absolute Max Ratings and some Electrical Characteristics Mark Miller 08/07/08 L. Timpa 10/6/16 B Transferred to the new TT Electronics template General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. © TT electronics plc OPTEK Technology, Inc. 1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200 www.optekinc.com | www.ttelectronics.com Issue B 10/2016 Page 6