TSC FRA1606G 16.0 amps. glass passivated fast recovery rectifier Datasheet

FRA1601G - FRA1607G
16.0 AMPS. Glass Passivated Fast Recovery Rectifiers
TO-220AC
.185(4.70)
.175(4.44)
.412(10.5)
MAX
Features
.113(2.87)
.103(2.62)
Glass passivated chip junction.
High efficiency, Low VF
High current capability
High reliability
High surge current capability
Low power loss
.27(6.86)
.23(5.84)
.594(15.1)
.587(14.9)
PIN1
2
.16(4.06)
.14(3.56)
.11(2.79)
.10(2.54)
.56(14.22)
.53(13.46)
.037(0.94)
.027(0.68)
Mechanical Data
.055(1.40)
.045(1.14)
DIA
.154(3.91)
.148(3.74)
.025(0.64)
.014(0.35)
.205(5.20)
.195(4.95)
Cases: TO-220AC Molded plastic
Epoxy: UL 94V-0 rate flame retardant
Terminals: Pure tin plated, Lead free. Leads
solderable per MIL-STD-202, Method 208
guaranteed
Polarity: As marked
High temperature soldering guaranteed:
o
260 C /10 seconds, 0.16”,(4.06mm) from
case.
Mounting position: Any
Weight: 2.24 grams
PIN 1
PIN 2
CASE
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25 oC ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Symbol FRA
FRA
FRA
FRA
FRA
FRA
FRA
1601G 1602G 1603G 1604G 1605G 1606G 1607G
Type Number
Maximum Recurrent Peak Reverse Voltage
V RRM
50
Maximum RMS Voltage
V RMS
V DC
Maximum DC Blocking Voltage
Maximum Average Forward Rectified Current
See Fig. 1
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@ 16.0A
100
200
400
600
800
35
70
140
280
420
50
100
200
400
600
Units
1000
V
560
700
V
800
1000
V
I(AV)
16.0
A
IFSM
250
A
VF
1.3
V
Maximum DC Reverse Current @ T C =25 C
at Rated DC Blocking Voltage @ T C =125 oC
IR
5.0
100
Maximum Reverse Recovery Time ( Note 1)
Trr
Typical Junction Capacitance ( Note 3 )
Cj
uA
uA
nS
pF
o
C/W
o
C
o
Typical Thermal resistance ( Note 2 )
R θJC
150
250
70
2.5
-65 to +150
Operating and Storage Temperature Range
T J ,T STG
1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A
Notes:
2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink
Size 2” x 3” x 0.25” Al-Plate.
3. Measured at 1MHz and Applied Reverse Voltage of 4.0 Volts D.C.
500
Version: A06
RATINGS AND CHARACTERISTIC CURVES (FRA1601G THRU FRA1607G)
1000
16
INSTANTANEOUS REVERSE CURRENT. ( A)
AVERAGE FORWARD CURRENT. (A)
FIG.2- TYPICAL REVERSE CHARACTERISTICS
PER LEG
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
20
12
8
4
0
0
50
100
150
o
CASE TEMPERATURE. ( C)
FIG.3- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
100
Tj=125 0C
10
1
Tj=25 0C
PEAK FORWARD SURGE CURRENT. (A)
300
TJ=125 0C
250
0.1
8.3ms Single Half Sine Wave
JEDEC Method
200
0
20
40
60
80
100
120
140
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
150
100
80
FIG.5- TYPICAL INSTANTANEOUS FORWARD
CHARACTERISTICS PER LEG
50
40
0
2
5
10
20
50
100
NUMBER OF CYCLES AT 60Hz
FIG.4- TYPICAL JUNCTION CAPACITANCE
150
125
CAPACITANCE.(pF)
20
INSTANTANEOUS FORWARD CURRENT. (A)
1
100
75
50
10
4
2
1
0.4
0
25
0
0.1
Tj=25 C
f=1.0MHz
Vsig=50mVp-p
0.5
1
Tj=25oC
Pulse Width=300 s
1% Duty Cycle
0.2
5
10
50
100
0.1
0.8
500 1000
0.9
1.0
1.1
1.2
1.3
1.4
1.5
INSTANTANEOUS FORWARD VOLTAGE. (V)
REVERSE VOLTAGE. (V)
FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
10W
NONINDUCTIVE
trr
+0.5A
(-)
DUT
(+)
50Vdc
(approx)
(-)
PULSE
GENERATOR
(NOTE 2)
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
0
-0.25A
(+)
-1.0A
1cm
SET TIME BASE FOR
5/ 10ns/ cm
Version: A06
Similar pages