Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Film Type Data Sheet 1 Chip Inductor (Chip Coil) for High Frequency Film Type LQP03T_04 Series (0201 Size) oReplacement: This product is in production, but LQP03T_02 is strongly recommended for stable supply in the future. c Dimensions c Packaging Colored Side Code Packaging Minimum Quantity D 180mm Paper Tape 10000 J 330mm Paper Tape 50000 B Bulk(Bag) 500 0.30±0.05 Colored Side 0.60±0.05 *Polarity Marking 0.30±0.05 *Inductance: 1.0 to 56nH 0.15±0.05 (in mm) c Rated Value (p: packaging code) Part Number Inductance LQP03TN0N6B04p 0.6nH ±0.1nH Test Frequency Rated Current Max. of DC Resistance Q (min.) Test Frequency Self Resonance Frequency (min.) 500MHz 420mA 0.08ohm 13 500MHz 6000MHz LQP03TN0N6C04p 0.6nH ±0.2nH 500MHz 420mA 0.08ohm 13 500MHz 6000MHz LQP03TN0N7B04p 0.7nH ±0.1nH 500MHz 410mA 0.09ohm 13 500MHz 6000MHz LQP03TN0N8B04p 0.8nH ±0.1nH 500MHz 410mA 0.09ohm 13 500MHz 6000MHz LQP03TN0N8C04p 0.8nH ±0.2nH 500MHz 410mA 0.09ohm 13 500MHz 6000MHz LQP03TN0N9B04p 0.9nH ±0.1nH 500MHz 400mA 0.10ohm 13 500MHz 6000MHz LQP03TN1N0B04p 1.0nH ±0.1nH 500MHz 400mA 0.10ohm 13 500MHz 6000MHz LQP03TN1N0C04p 1.0nH ±0.2nH 500MHz 400mA 0.10ohm 13 500MHz 6000MHz LQP03TN1N1B04p 1.1nH ±0.1nH 500MHz 280mA 0.13ohm 13 500MHz 6000MHz LQP03TN1N2B04p 1.2nH ±0.1nH 500MHz 280mA 0.13ohm 13 500MHz 6000MHz LQP03TN1N2C04p 1.2nH ±0.2nH 500MHz 280mA 0.13ohm 13 500MHz 6000MHz LQP03TN1N3B04p 1.3nH ±0.1nH 500MHz 280mA 0.16ohm 13 500MHz 6000MHz LQP03TN1N4B04p 1.4nH ±0.1nH 500MHz 280mA 0.16ohm 13 500MHz 6000MHz LQP03TN1N5B04p 1.5nH ±0.1nH 500MHz 280mA 0.16ohm 13 500MHz 6000MHz LQP03TN1N5C04p 1.5nH ±0.2nH 500MHz 280mA 0.16ohm 13 500MHz 6000MHz LQP03TN1N6B04p 1.6nH ±0.1nH 500MHz 280mA 0.16ohm 13 500MHz 6000MHz LQP03TN1N7B04p 1.7nH ±0.1nH 500MHz 280mA 0.16ohm 13 500MHz 6000MHz LQP03TN1N8B04p 1.8nH ±0.1nH 500MHz 280mA 0.16ohm 13 500MHz 6000MHz LQP03TN1N8C04p 1.8nH ±0.2nH 500MHz 280mA 0.16ohm 13 500MHz 6000MHz LQP03TN1N9B04p 1.9nH ±0.1nH 500MHz 220mA 0.18ohm 13 500MHz 6000MHz LQP03TN2N0B04p 2.0nH ±0.1nH 500MHz 220mA 0.18ohm 13 500MHz 6000MHz LQP03TN2N1B04p 2.1nH ±0.1nH 500MHz 220mA 0.18ohm 13 500MHz 6000MHz LQP03TN2N2B04p 2.2nH ±0.1nH 500MHz 220mA 0.18ohm 13 500MHz 6000MHz LQP03TN2N2C04p 2.2nH ±0.2nH 500MHz 220mA 0.18ohm 13 500MHz 6000MHz Operating Temperature Range (Self-temperature rise is not included): -40 to +85°C Only for reflow soldering. Continued on the following page. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.9.8 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Film Type Data Sheet 2 Continued from the preceding page. Part Number Inductance Test Frequency Rated Current Max. of DC Resistance Q (min.) Test Frequency Self Resonance Frequency (min.) LQP03TN2N3B04p 2.3nH ±0.1nH 500MHz 220mA 0.20ohm 13 500MHz 6000MHz LQP03TN2N4B04p 2.4nH ±0.1nH 500MHz 220mA 0.20ohm 13 500MHz 6000MHz LQP03TN2N5B04p 2.5nH ±0.1nH 500MHz 220mA 0.20ohm 13 500MHz 6000MHz LQP03TN2N6B04p 2.6nH ±0.1nH 500MHz 220mA 0.20ohm 13 500MHz 6000MHz LQP03TN2N7B04p 2.7nH ±0.1nH 500MHz 220mA 0.20ohm 13 500MHz 6000MHz LQP03TN2N7C04p 2.7nH ±0.2nH 500MHz 220mA 0.20ohm 13 500MHz 6000MHz LQP03TN2N8B04p 2.8nH ±0.1nH 500MHz 220mA 0.20ohm 13 500MHz 6000MHz LQP03TN2N9B04p 2.9nH ±0.1nH 500MHz 220mA 0.20ohm 13 500MHz 6000MHz LQP03TN3N0B04p 3.0nH ±0.1nH 500MHz 190mA 0.20ohm 13 500MHz 6000MHz LQP03TN3N1B04p 3.1nH ±0.1nH 500MHz 190mA 0.20ohm 13 500MHz 6000MHz LQP03TN3N2B04p 3.2nH ±0.1nH 500MHz 190mA 0.20ohm 13 500MHz 6000MHz LQP03TN3N3B04p 3.3nH ±0.1nH 500MHz 190mA 0.20ohm 13 500MHz 6000MHz LQP03TN3N3C04p 3.3nH ±0.2nH 500MHz 190mA 0.20ohm 13 500MHz 6000MHz LQP03TN3N4B04p 3.4nH ±0.1nH 500MHz 190mA 0.30ohm 13 500MHz 6000MHz LQP03TN3N5B04p 3.5nH ±0.1nH 500MHz 190mA 0.30ohm 13 500MHz 6000MHz LQP03TN3N6B04p 3.6nH ±0.1nH 500MHz 170mA 0.30ohm 13 500MHz 6000MHz LQP03TN3N7B04p 3.7nH ±0.1nH 500MHz 170mA 0.30ohm 13 500MHz 6000MHz LQP03TN3N8B04p 3.8nH ±0.1nH 500MHz 170mA 0.30ohm 13 500MHz 6000MHz LQP03TN3N9B04p 3.9nH ±0.1nH 500MHz 170mA 0.30ohm 13 500MHz 6000MHz LQP03TN3N9C04p 3.9nH ±0.2nH 500MHz 170mA 0.30ohm 13 500MHz 6000MHz LQP03TN4N3H04p 4.3nH ±3% 500MHz 160mA 0.40ohm 13 500MHz 6000MHz LQP03TN4N7H04p 4.7nH ±3% 500MHz 160mA 0.40ohm 13 500MHz 6000MHz LQP03TN4N7J04p 4.7nH ±5% 500MHz 160mA 0.40ohm 13 500MHz 6000MHz LQP03TN5N1H04p 5.1nH ±3% 500MHz 140mA 0.55ohm 13 500MHz 6000MHz LQP03TN5N6H04p 5.6nH ±3% 500MHz 140mA 0.55ohm 13 500MHz 6000MHz LQP03TN5N6J04p 5.6nH ±5% 500MHz 140mA 0.55ohm 13 500MHz 6000MHz LQP03TN6N2H04p 6.2nH ±3% 500MHz 130mA 0.60ohm 13 500MHz 6000MHz LQP03TN6N2J04p 6.2nH ±5% 500MHz 130mA 0.60ohm 13 500MHz 6000MHz LQP03TN6N8H04p 6.8nH ±3% 500MHz 130mA 0.60ohm 13 500MHz 6000MHz LQP03TN6N8J04p 6.8nH ±5% 500MHz 130mA 0.60ohm 13 500MHz 6000MHz LQP03TN7N5H04p 7.5nH ±3% 500MHz 110mA 0.65ohm 13 500MHz 5500MHz LQP03TN7N5J04p 7.5nH ±5% 500MHz 110mA 0.65ohm 13 500MHz 5500MHz LQP03TN8N2H04p 8.2nH ±3% 500MHz 110mA 0.86ohm 13 500MHz 5500MHz LQP03TN8N2J04p 8.2nH ±5% 500MHz 110mA 0.86ohm 13 500MHz 5500MHz LQP03TN9N1H04p 9.1nH ±3% 500MHz 100mA 1.10ohm 13 500MHz 4500MHz LQP03TN9N1J04p 9.1nH ±5% 500MHz 100mA 1.10ohm 13 500MHz 4500MHz LQP03TN10NH04p 10nH ±3% 500MHz 100mA 1.10ohm 13 500MHz 4500MHz LQP03TN10NJ04p 10nH ±5% 500MHz 100mA 1.10ohm 13 500MHz 4500MHz LQP03TN12NH04p 12nH ±3% 500MHz 90mA 1.15ohm 11 500MHz 3700MHz LQP03TN12NJ04p 12nH ±5% 500MHz 90mA 1.15ohm 11 500MHz 3700MHz LQP03TN15NH04p 15nH ±3% 500MHz 90mA 1.40ohm 11 500MHz 3300MHz LQP03TN15NJ04p 15nH ±5% 500MHz 90mA 1.40ohm 11 500MHz 3300MHz LQP03TN18NH04p 18nH ±3% 500MHz 80mA 1.60ohm 11 500MHz 3100MHz LQP03TN18NJ04p 18nH ±5% 500MHz 80mA 1.60ohm 11 500MHz 3100MHz LQP03TN22NH04p 22nH ±3% 500MHz 70mA 2.55ohm 11 500MHz 2800MHz Operating Temperature Range (Self-temperature rise is not included): -40 to +85°C Only for reflow soldering. Continued on the following page. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.9.8 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Film Type Data Sheet 3 Continued from the preceding page. Part Number Inductance Test Frequency Rated Current Max. of DC Resistance Q (min.) Test Frequency Self Resonance Frequency (min.) LQP03TN22NJ04p 22nH ±5% 500MHz 70mA 2.55ohm 11 500MHz 2800MHz LQP03TN27NH04p 27nH ±3% 500MHz 70mA 2.90ohm 11 500MHz 2500MHz LQP03TN27NJ04p 27nH ±5% 500MHz 70mA 2.90ohm 11 500MHz 2500MHz LQP03TN33NJ04p 33nH ±5% 300MHz 60mA 2.95ohm 8 300MHz 2000MHz LQP03TN39NJ04p 39nH ±5% 300MHz 60mA 3.35ohm 8 300MHz 1800MHz LQP03TN47NJ04p 47nH ±5% 300MHz 50mA 3.60ohm 8 300MHz 1600MHz LQP03TN56NJ04p 56nH ±5% 300MHz 50mA 4.30ohm 8 300MHz 1400MHz Operating Temperature Range (Self-temperature rise is not included): -40 to +85°C Only for reflow soldering. c Q-Frequency Characteristics (Typ.) c Inductance-Frequency Characteristics (Typ.) 80 1000 1.5nH 56nH Inductance (nH) 60 Q 3.9nH 6.8nH 40 10nH 27nH 100 15nH 10nH 10 6.8nH 15nH 20 3.9nH 27nH 1.5nH 56nH 0 100 1000 Frequency (MHz) 1 100 10000 1000 Frequency (MHz) 10000 c !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. oThis data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.9.8 http://www.murata.com/