Omron A165K-J3MR-2 Separate construction with cylindrical 16-dia. body Datasheet

Key-type Selector Switch (Detachable) (Cylindrical 16-dia.)
A165K
CSM_A165K_DS_E_3_1
Separate Construction with Cylindrical
16-dia. Body
• Short mounting depth, less than 28.5 mm below panel
• Wide range of switching capacity from standard to microload
• Oil-resistant IP65 models
Refer to Safety Precautions for All Pushbutton Switches and
Safety Precautions on page 11.
List of Models
Rectangular
Solder
terminals
Screwless
clamp
connector
Model
Square
Round
A165K-J Series
A165K-A Series
A165K-T Series
A165K-J Series
A165K-A Series
A165K-T Series
1
A165K
Model Number Structure
Model Number Legend ..... The model numbers used to order sets of Units are illustrated below. One set comprises the Selector, Switch,
and 2 Keys.
For information on combinations, refer to Ordering Information on page 3.
(1)
(2)
(3)
A165K- J 3ML - 2
(1) Shape of Selector
Symbol
Shape
Color
J
Rectangular
A
Square
Black
T
Round
(2) Number of Notches/Resetting Method
Symbol
2ML
2MR
2M
2AL
3MC
3MR
3ML
No. of
notches
2 notches
Reset
method
Manual
Automatic
3 notches Manual
3M
3AC
3 notches Automatic
Key release
position
Left
Right
Left and right
Left
Center
Right
Left
Left, right,
and center
Center
(3) Contact Configuration
Symbol
1
2
2S
Type
SPDT
DPDT
DPDT
Terminal
Solder Terminal
Screw-less Clamp
Note: Only DPDT contacts are available with
3-notch models.
2
A165K
Ordering Information
Ordering as a Set .................The model numbers used to order sets of Units are given in the following tables. One set comprises the
Selector, Switch and 2 Keys.
Solder Terminals
Rectangular Models
Oil-resistant IP65
Number of
notches
Output
SPDT
A165K-J
Reset method
Left
Right
Left and right
Left
Left
Right
Left and right
Left
Center
Right
Left
Left, right, and center
Manual
Automatic
2 notches
DPDT
Manual
Automatic
3 notches
DPDT
Key release position
Manual
Model
A165K-J2ML-1
A165K-J2MR-1
A165K-J2M-1
A165K-J2AL-1
A165K-J2ML-2
A165K-J2MR-2
A165K-J2M-2
A165K-J2AL-2
A165K-J3MC-2
A165K-J3MR-2
A165K-J3ML-2
A165K-J3M-2
Square Models
A165K-A
Oil-resistant IP65
Number of
notches
Output
SPDT
Reset method
Left
Right
Left and right
Left
Left
Right
Left and right
Left
Center
Right
Left
Left, right, and center
Manual
Automatic
2 notches
DPDT
Manual
Automatic
3 notches
DPDT
Key release position
Manual
Model
A165K-A2ML-1
A165K-A2MR-1
A165K-A2M-1
A165K-A2AL-1
A165K-A2ML-2
A165K-A2MR-2
A165K-A2M-2
A165K-A2AL-2
A165K-A3MC-2
A165K-A3MR-2
A165K-A3ML-2
A165K-A3M-2
Round Models
A165K-T
Oil-resistant IP65
Number of
notches
Output
SPDT
Reset method
Manual
Automatic
2 notches
DPDT
Manual
Automatic
3 notches
DPDT
Manual
Key release position
Left
Right
Left and right
Left
Left
Right
Left and right
Left
Center
Right
Left
Left, right, and center
Model
A165K-T2ML-1
A165K-T2MR-1
A165K-T2M-1
A165K-T2AL-1
A165K-T2ML-2
A165K-T2MR-2
A165K-T2M-2
A165K-T2AL-2
A165K-T3MC-2
A165K-T3MR-2
A165K-T3ML-2
A165K-T3M-2
3
A165K
Ordering Information
Ordering Individually ......... Selectors and Switches can be ordered separately. Combinations that are not available as sets can be created
using individual Units. Also, store the parts as spares for maintenance and repairs.
Operation Units (Listed on Page 5.)
Rectangular
(A165K-J)
Square
(A165K-A)
Round
(A165K-T)
(Standard condition when shipped)
Switches with
2 Notches
FP
·Two keys are provided.
(75°)
90°
Switches with
3 Notches
(45°)
45°
FP
(45°)
45°
Note: The figures in parentheses are for
self-resetting models.
FP: Free position
Socket Units (Listed on Page 5.)
Solder terminals
PCB terminals
Screw-less clamp
connector
4
A165K
Ordering Information
Ordering Individually .........Selectors and Switches can be ordered separately. Combinations that are not available as sets can be created
using individual Units. Also, store the parts as spares for maintenance and repairs.
Selectors
Appearance
Rectangular
(A165K-J)
Number of notches
2 notches
Reset method
Key release position
Model
A165K-J2ML
A165K-J2MR
A165K-J2M
A165K-J2AL
A165K-J3MC
A165K-J3MR
A165K-J3ML
A165K-J3M
A165K-J3AC
A165K-A2ML
A165K-A2MR
A165K-A2M
A165K-A2AL
A165K-A3MC
A165K-A3MR
A165K-A3ML
A165K-A3M
A165K-A3AC
A165K-T2ML
A165K-T2MR
A165K-T2M
A165K-T2AL
A165K-T3MC
A165K-T3MR
A165K-T3ML
A165K-T3M
A165K-T3AC
Manual
Automatic
3 notches
Manual
Automatic
Square
(A165K-A)
2 notches
Manual
Automatic
3 notches
Manual
Automatic
Round
(A165K-T)
2 notches
Manual
Automatic
3 notches
Manual
Automatic
Switches
Appearance
Classification
Model
SPDT
A16S-2N-1
2 notches
DPDT
Switch
3 notches
Solder terminal
DPDT
A16S-3N-2
SPDT
2 notches
A16S-2N-2
A16S-2N-1P
PCB terminal
DPDT
A16S-2N-2P
Switches with Screw-less Clamp
Appearance
Classification
Model
2 notches
Common to standard
load and microload.
DPDT
A16-2S
Remarks
Common to ones
for pushbutton
switches.
Non-lighted
3 notches
A16S-3N-2LS
---
5
A165K
Ordering Information
Accessories and Tools (Order Separately)
Accessories
Name
Appearance
Classification
Panel Plugs
Model
Rectangular
A16ZJ-3003
Square
A16ZA-3003
Round
A16ZT-3003
Remarks
Used for covering the panel
cutouts for future panel
expansion.
Degree of protection: IP40
Color: Black
Tools
Name
Appearance
Screw Fitting
Extractor
Model
A16Z-3004
A16Z-5080
Pushbutton
Switch
Knob-type
Selector
Switch
Yes
Yes
Yes
Yes
Applicable types
Key-type
Emergency
Selector
Stop
Switch
Switch
Yes
Yes
Yes
Yes
Remarks
Indicator
Yes
Convenient
for ganged
installation.
Yes
Convenient for
extracting the
Lamp from a
Solder-terminal
Socket Unit.
Key
Appearance
Model
A165K-KEY
Note: Two Keys are provided.
Ordering as a Set: Refer to page 3.
■ Specifications, and dimensions: Refer to page 7 to 10.
■ Accessories, replacements, and tools: Refer to this page.
6
A165K
Specifications
Approved Standard Ratings
UL, cUL (File No. E41515)
TÜV (EN60947-5-1) (Low Voltage Directive)
CCC (GB14048.5)
5 A at 125 VAC, 3 A at 250 VAC (general use)
3 A at 30 VDC (resistive)
3 A at 250 VAC
3 A at 30 VDC
5 A at 125 VAC
3 A at 250 VAC
3 A at 30 VDC
Note: Certification has been obtained for the Switch Unit.
For detailed information on individual products that
have received certification, consult your supplier.
Ratings
Contacts
Contact Form
Rated voltage
Resistive load
125 VAC
5A
250 VAC
3A
30 VDC
3A
Name
Contact form
NC
SPDT
COM
NO
Minimum applicable load: 1 mA at 5 VDC
Rated values are obtained from tests conducted under the following conditions.
1. Load: Resistive load
2. Mounting conditions: No vibration and no shock
3. Temperature: 20±2°C
4. Operating frequency: 20 times/min
Characteristics
Operating Characteristics
Socket Units
Type
Item
Type
Allowable
operating
frequency
Key-type Selector Switch
Characteristics
Mechanical
20 operations/minute max.
Operating force (OF) max.
Electrical
10 operations/minute max.
Set position (SP)
100 MΩ min. (at 500 VDC)
Operation Angle
Insulation resistance
Between terminals
of same polarity
Dielectric
strength
1,000 VAC, 50/60 Hz for 1 minute
Between terminals
of different polarity
Between each terminal and ground
Vibration
resistance
Shock
resistance
Durability
(45°)
45°
90°
45° +100
Three notches
(75°)
FP
3 notches
0.1 N·m
90±5°
Two notches
2,000 VAC, 50/60 Hz for 1 minute
Key-type Selector Switch
2 notches
FP
(45°)
45°
2,000 VAC, 50/60 Hz for 1 minute
10 to 55 Hz, 1.5-mm double amplitude
(malfunction within 1 ms)
Malfunction
Destruction
500 m/s2
Malfunction
150 m/s2 max. (malfunction within 1 ms)
Mechanical
250,000 operations min. (durability of key:
10,000 operations min.)
Electrical
Contact Configuration
100,000 operations min.
Electric shock protection
class
Note: The angle used for automatic reset is shown in parentheses.
FP: Free position
Contact configuration
Class II
PTI (tracking characteristic)
Degree of contamination
No. of
notches
175
3 (IEC60947-5-1)
Approx. 26.5 g (in the case of a DPDT
switch key)
Weight
−10°C to 55°C
(with no icing or condensation)
Ambient operating
temperature
Ambient operating humidity
35% to 85%RH
−25°C to 65°C
(with no icing or condensation)
Ambient storage
temperature
SPDT
Position
SW
DPDT
Position
SW1
SW2
2
notches
3
notches
---
Screw-less Clamp
Item
Type
Recommended wire size
Usable
wires and
tensile
strength
Twisted wire
Solid wire
Tensile strength
SW1
Screw-less Clamp
SW2
0.5 mm2 twisted wire or 0.8 mm-dia. solid wire
0.3 mm2
0.5 mm2
0.75 mm2
0.5 mm dia. 0.8 mm dia. 1.0 mm dia.
10 N
20 N
30 N
1.25 mm2
--40 N
Length of exposed wire
10 ±1 mm
Compliant standards
JIS C 2811 Terminal Blocks for Industrial Use
7
A165K
Nomenclature
Model Structure
Selector
●Key
●Flange Shape
Rectangular
(A165K-J)
●Number of Notches and Reset Method
· 2 Notches: Manual, Automatic
· 3 Notches: Manual, Automatic
Square
(A165K-A)
Round
(A165K-T)
●Protective
Structure
Oil-resistant IP65
Switch
●Switch Specifications
5 A at 125 VAC
5 A at 250 VAC
3 A at 130 VDC
Minimum applicable load
1 mA at 25 VDC
●Terminal Type
Solder terminals
PCB terminals
The flange can be rotated to easily change the operation angle
of the knob.
For information on rotating the flange, refer to the A165S/W
datasheet.
Example: Knob-type Selector Switch with Two Notches
FP
(75°)
90°
90°
90°
(Standard condition when shipped)
Note: The angle is 75° for self-resetting models.
8
A165K
Dimensions
(Unit: mm)
The Dimension shows 2-switch outputs.
Rectangular A165K-J
Solder terminals (tab terminals #110)
M16×1
1.5
12.2
18
4
10.8
9.5
21.1
28.5
34.5 ±1
2.8
20
12.4 15.8
18
24
Model, standard, lot No., serial number
Mounting nut
Packing (t0.5)
Lock ring
* Refer to the A165S/W for Panel cutouts.
Square A165K-A
Solder terminals (tab terminals #110)
M16×1
1.5
12.2
18
4
10.8
9.5
21.1
28.5
34.5 ±1
2.8
20
12.4 15.8
18
18
Model, standard, lot No., serial number
Mounting nut
Packing (t0.5)
Lock ring
* Refer to the A165S/W for Panel cutouts.
Round A165K-T
Solder terminals (tab terminals #110)
M16×1
1.5
12.2
18
4
10.8
9.5
34.5 ±1
21.1
28.5
2.8
20
12.4 15.8
18
18
Model, standard, lot No., serial number
Packing (t0.5)
Mounting nut
Lock ring
* Refer to the A165S/W for Panel cutouts.
9
A165K
Dimensions
• The Dimension shows 2-switch outputs.
• The lamp terminal is also provided with non-lighted models.
Rectangular A165K@-2S
Screw-Less Clamp
9.5
• A rectangular model is listed as an example.
Panel Cutouts
48.9
10.8
4
(Unit: mm)
2
16 +0.2
0 dia.
24
25 min.
23.9
M16×1
33 min.
Switch dismounting lever
Lock ring
Mounting nut
(31.7) 27.4
18
24
23.5
Packing (t0.5)
Recommended panel
thickness: 0.5 to 3.2 mm
Terminal Arrangement
For information on the terminal arrangement, refer to the A165S/W datasheet.
Panel Mounting and Socket Unit Mounting and Removal
Refer to the A16 Pushbutton Switch datasheet.
Flange Rotation
Refer to the A165S/W datasheet.
10
A165K
Safety Precautions
Refer to Safety Precautions for All Pushbutton Switches.
WARNING
Always turn OFF the power and wait for 10 minutes
before replacing the incandescent lamp. If the lamp is
replaced immediately after the power is turned OFF,
the remaining heat may cause burns.
Precautions for Correct Use
Mounting
• Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance.
• Do not tighten the mounting nut more than necessary using tools
such as pointed-nose pliers. Doing so will damage the mounting
nut.
The tightening torque is 0.29 to 0.49 N·m.
Wiring
• Solder terminals and quick-connect terminals (#110) are commonly
used for terminals.
• Be sure to use electrical wires that are a size appropriate for the
applied voltage and carry current (conductor size is 0.5 to 0.75
mm2). Perform soldering according to the conditions provided
below. If the soldering is not properly performed, the lead wires will
become detached, resulting in short-circuits.
1. Hand soldering: 350°C, within 3 s
2. Dip soldering: 350°C, within 3 s
Wait for one minute after soldering before exerting any external
force on the solder.
• Use non-corrosive resin fluid as the flux.
• Make sure that the electric cord is wired so that it does not touch
the Unit. If the electric cord touches the Unit, then electric wires with
a heat resistance of 100°C min. must be used.
• After wiring the Switch, maintain an appropriate clearance and
creepage distance.
Using the Microload
• Insert a contact protection circuit, if necessary, to prevent the
reduction of life expectancy due to extreme wear on the contacts
caused by loads where inrush current occurs when the contact is
opened and closed.
• The A16 allows both a standard load (125 V at 5A, 250 V at 3 A)
and a microload. If a standard load is applied, however, the
microload area cannot be used. If the microload area is used with a
standard load, the contact surface will become rough, and the
opening and closing of the contact for a microload may become
unreliable.
• The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability
level of 60% (λ 60) (conforming to JIS C5003).
The equation, λ 60 = 0.5 × 10-4/operations indicates that the
estimated malfunction rate is less than 1/2,000,000 operations with
a reliability level of 60%.
Voltage (V)
Do not apply a voltage between the incandescent
lamp and the terminal that is greater than the rated
voltage. If the incandescent lamp is broken, the
operating part may pop out.
0.15 mA
30
24
Microload area
12
Invalid
area
5
0
0.1
1 mA
1
10
100
1,000
Current (mA)
Operating Environment
• The IP65 model is designed with a degree of protection so that it
will not sustain damage if it is subjected to water from any direction
to the front of the panel.
11
A165K
Others
• The oil-resistant IP65 uses NBR rubber and is resistant to general
cutting oil and cooling oil. Some particular oils cannot be used with
the oil-resistant IP65, however, so contact your OMRON
representative for details.
• If the panel is to be finished with coating, etc., make sure that the
panel meets the specified dimensions after the coating.
• Do not subject the Switch to extreme shock or vibration. Doing so
will cause malfunctions and damage to the Switch.
Do not let sharp objects come into contact with the Switches that
are made of resin. Doing so will damage the Switches, causing
scratches on the outside of the operating parts, and malfunction.
When handling the Switches, do not throw or drop them.
Do not allow the Switch
to drop and hit the
ground.
Do not place or drop
heavy objects on the
Switch.
Do not operate the Switch
with hard or sharp objects.
Hammer
Screwdriver
12
Read and Understand This Catalog
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or
comments.
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)
from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR
FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS
DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS
IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT
LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS
OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT
SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's
application or use of the products.
At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the
products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,
machine, system, or other application or use.
The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible
uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:
• Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.
• Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,
safety equipment, and installations subject to separate industry or government regulations.
• Systems, machines, and equipment that could present a risk to life or property.
Please know and observe all prohibitions of use applicable to the products.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.
PROGRAMMABLE PRODUCTS
OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons.
It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or
establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual
specifications of purchased products.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the
result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON
Warranty and Limitations of Liability.
ERRORS AND OMISSIONS
The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,
typographical, or proofreading errors, or omissions.
2009.9
In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2009 All Right Reserved.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Omron:
A16ZJ-3003 A16ZJ-5050 A16ZA-5001W
Similar pages