E M C C o m p o n e n t s December 2015 Common Mode Filters For automobile signal line ACT Series ACT1210 Type ACT1210 [1210 inch]* (CAN-BUS, FlexRay) * Dimensions Code JIS[EIA] (2/8) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20151227 / cmf_automotive_signal_act1210_en.fm (3/8) E M C C o m p o n e n t s Common Mode Filters Product compatible with RoHS directive Halogen-free Compatible with lead-free solders AEC-Q200 For automobile signal line Overview of ACT1210 Type FEATURES Compact products (3225 size), whose characteristics are equivalent to that of conventional products (ACT45B, ACT45R). Common mode filters for CAN-BUS/FlexRay, compatible with an operating temperature range of –55 to +150°C. APPLICATION CAN-BUS, FlexRay system. PART NUMBER CONSTRUCTION ACT1210 Series • Type name - 110 Inductance(typ.) (μH) 110 11 220 22 510 51 101 100 - 2P - Number of lines 2P 2 lines TL TL 00 Packaging style Internal code ø330mm reel 00 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Type Operating temperature （°C） ACT1210 –55 to +150 Package quantity Individual weight (pieces/reel) 6,000 （g） 0.075 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151227 / cmf_automotive_signal_act1210_en.fm (4/8) E M C C o m p o n e n t s ACT1210 Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 40s max. Peak Temp. T4 245°C Time t3 5s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151227 / cmf_automotive_signal_act1210_en.fm (5/8) E M C C o m p o n e n t s ACT1210 Type SHAPE & DIMENSIONS 3.9max. 4 2 3 Marking 2.5max. 2.5±0.2 1 4x 0.1 CZ 3.2±0.2 Dimensions in mm 1.6 0.4 RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 1 4 2 3 2.0 4.1 Dimensions in mm • No polarity Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151227 / cmf_automotive_signal_act1210_en.fm (6/8) E M C C o m p o n e n t s ACT1210 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance Common mode inductance Stray inductance DC resistance Rated current Insulation resistance Rated voltage [10MHz 100mV] (: )min. (: )typ. 300 550 500 1100 1000 2600 2200 5100 [100kHz 100mV] (μH)+50/–30% 11 22 51 100 [100kHz 100mV] (μH)typ. 0.05 0.06 0.09 0.13 (: )max. 0.4 0.5 0.7 1.5 (M: )min. 10 10 10 10 (V)max. 80 80 80 80 ○ Derating ACT1210-110-2P-TL00 ACT1210-220-2P-TL00 ACT1210-510-2P-TL00 ACT1210-101-2P-TL00 ○ Maximum current value for the ambient temperature (mA) Ambient temperature Part No. 125°C 140°C 150°C ACT1210-110-2P-TL00 300 200 100 ACT1210-220-2P-TL00 250 166 83 ACT1210-510-2P-TL00 200 133 66 ACT1210-101-2P-TL00 150 100 50 1.2 1 0.8 Iop/IR (mA)max. 300 250 200 150 Part No. 0.6 0.4 0.2 0 0 25 50 75 100 Ambient temperature(°C) ○ Measurement equipment Measurement item Product No. Common mode impedance 4991A Common mode inductance 4294A DC resistance 4338A Insulation resistance 4339A ＊ Equivalent measurement equipment may be used. 125 150 Manufacturer Keysight Technologies Keysight Technologies Keysight Technologies Keysight Technologies Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151227 / cmf_automotive_signal_act1210_en.fm (7/8) E M C C o m p o n e n t s ACT1210 Type ELECTRICAL CHARACTERISTICS IMPEDANCE VS. FREQUENCY CHARACTERISTICS 100000 510 Common mode Impedance (Ω) 10000 101 Common mode 220 Common mode 1000 510 Differential mode 110 Common mode 101 Differential mode 100 220 Differential mode 110 Differential mode 10 1 1 10 100 1000 Frequency (MHz) ○ Measurement equipment Product No. Manufacturer 4991A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151227 / cmf_automotive_signal_act1210_en.fm (8/8) E M C C o m p o n e n t s ACT1210 Type PACKAGING STYLE REEL DIMENSIONS 2.0±0.5 E A ø330±2 W1 13.5±0.5 W2 17.5±1 N 100±1 E 2 typ. N Type ACT1210 1.0 ø13.0±0.2 W1 ø21.0±0.8 W2 A Dimensions in mm TAPE DIMENSIONS P2 t P0 W B F E øD0 A K P1 Dimensions in mm Type ACT1210 A 2.85±0.1 B 4.2±0.1 øD0 1.5+0.1/–0 E 1.75±0.1 F 5.5±0.05 P0 4±0.1 P1 4±0.1 P2 2±0.05 W 12+0.3/–0.1 K 2.7±0.1 t 0.35±0.1 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151227 / cmf_automotive_signal_act1210_en.fm