Revised August 2003 NC7SZ66 TinyLogic Low Voltage UHS Single SPST Normally Open Bus Switch General Description Features The NC7SZ66 is a ultra high-speed (UHS) CMOS compatible single-pole/single-throw (SPST) bus switch. The LOW On Resistance of the switch allows inputs to be connected to outputs with minimal propagation delay and without generating additional ground bounce noise. The device is organized as a 1-bit switch with a switch enable (OE) signal. When OE is HIGH, the switch is on and Port A is connected to Port B. When OE is LOW, the switch is open and a high-impedance state exists between the two ports. ■ Space saving SOT23 or SC70 5-lead package ■ Ultra small MicroPak leadless package ■ Broad VCC Operating Range 1.65V–5.5V ■ Rail-to-rail signal handling ■ 5Ω switch connection between two ports ■ Minimal propagation delay through the switch ■ Low ICC ■ Zero bounce in flow-through mode ■ Control input compatible with CMOS input levels Ordering Code: Order Package Product Code Number Number Top Mark NC7SZ66M5X MA05B 7Z66 5-Lead SOT23, JEDEC MO-178, 1.6mm NC7SZ66P5X MAA05A Z66 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide 3k Units on Tape and Reel NC7SZ66L6X MAC06 EE 6-Lead MicroPak, 1.0mm Wide 5k Units on Tape and Reel Package Description Logic Symbol Supplied As 3k Units on Tape and Reel Connection Diagrams Pin Assignments for SC70 Pin Descriptions (Top View) Pin Names Description OE Switch Enable Input A Bus A I/O B Bus B I/O NC No Connect Pad Assignment for MicroPak Function Table OE B0 Function L HIGH-Z State Disconnect H A0 Connect (Top Through View) TinyLogic is a registered trademark of Fairchild Semiconductor Corporation. MicroPak is a trademark of Fairchild Semiconductor Corporation. © 2003 Fairchild Semiconductor Corporation DS012177 www.fairchildsemi.com NC7SZ66 TinyLogic Low Voltage UHS Single SPST Normally Open Bus Switch November 1996 NC7SZ66 Absolute Maximum Ratings(Note 1) Recommended Operating Conditions (Note 3) −0.5V to +7.0V Supply Voltage (VCC) −0.5V to VCC +0.5V DC Switch Voltage (VS) Power Supply Operating (VCC) −0.5V to +7.0V DC Input Voltage (VIN) (Note 2) 0V to 5.5V Switch Input Voltage (VIN) 0V to VCC −50 mA Switch Output Voltage (VOUT) 0V to VCC 128 mA Input Rise and Fall Time (tr, tf) DC Input Diode Current (IIK) VIN < 0V DC Output (IOUT) Sink Current ±100 mA DC VCC /GND Current (ICC /IGND) 1.65V to 5.5V Control Input Voltage (VIN) Control Input; VCC = 2.3V−3.6V 0 ns/V to 10 ns Control Input; VCC = 4.5−5.5V Storage Temperature Range −65°C to +150°C (TSTG) 0 ns/V to 5 ns Switch I/O Junction Lead Temperature 0 ns/V to DC −40°C to +85°C Operating Temperature (TA) +150°C under Bias (TJ) Thermal Resistance (θJA) Junction Lead Temperature (TL) +260°C (Soldering, 10 Seconds) Power Dissipation (PD) @ +85°C SOT23-5 200 mW SC70-5 150 mW SOT23-5 300°C/Watt SC70-5 425°C/Watt Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 3: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics VCC Symbol VIH Parameter HIGH Level Input Voltage VIL LOW Level Input Voltage IIN Control Input Leakage Current IOFF OFF Leakage Current RON Switch On Resistance (Note 4) (V) TA= −40°C to +85°C Min 2.3 to 5.5 TA = +25°C Min Typ 0.25 VCC 2.3 to 5.5 0.3 VCC Units Conditions V 0 to 5.5 ±0.05 ±1.0 µA 0 ≤ VIN ≤ 5.5V 1.65 to 5.5 ±0.05 ±10.0 µA 0 ≤ A, B ≤ VCC 3 7 VIN = 0V, IIN = 30 mA 5 12 VIN = 2.4V, IIN = 15 mA 7 15 VIN = 4.5V, IIN = 30 mA 4 9 10 20 5 12 VIN = 0V, IIN = 8 mA 13 30 VIN = 2.3V, IIN = 8 mA 7 28 VIN = 0V, IIN = 4 mA 25 60 4.5 1.8 VIN = 0V, IIN = 24 mA Ω 5.0 6 (Note 4)(Note 6)(Note 7) 3.3 12 2.5 28 1.8 125 1.65 to 5.5 0.05 10 VIN = 3V, IIN = 24 mA VIN = 1.8V, IIN = 4 mA On Resistance Flatness Quiescent Supply Current Max V 0.7 VCC 1.65 to 1.95 2.3 ICC Max 1.65 to 1.95 0.75 VCC 3.0 Rflat Typ (Note 5) IA = −30 mA, 0 ≤ V Bn ≤ VCC Ω IA = −24 mA, 0 ≤ V Bn ≤ VCC IA = −8 mA, 0 ≤ VBn ≤ VCC IA = −4 mA, 0 ≤ VBn ≤ VCC µA VIN = VCC or GND IOUT = 0 Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A or B) pins. Note 5: All typical values are at the specified VCC, and TA = 25°C. Note 6: Parameter is characterized but not tested in production. Note 7: Flatness is defined as the difference between the maximum and minimum value of On Resistance over the specified range of conditions. www.fairchildsemi.com 2 TA= −40°C to +85°C, Symbol VCC Parameter (V) tPHL, tPLH Propagation Delay Bus to Bus CL= 50 pF, RU= RD = 500Ω Min Typ (Note 8) 1.65 to 1.95 (Note 9) tPLZ, tPHZ Output Enable Time Output Disable Time Conditions Figure Number 4.3 2.3-2.7 1.2 ns 3.0-3.6 0.8 ns 0.3 ns 4.5-5.5 tPZL, tPZH Units Max VIN = OPEN Figures 1, 2 1.65 to 1.95 1.5 7.0 14.2 2.3-2.7 1.5 3.3 7.0 ns VIN = 2 x VCC for tPZL 3.0-3.6 1.5 2.4 5.5 ns VIN = 0V for tPZH ns 4.5-5.5 1.5 2.0 4.5 1.65 to 1.95 1.5 9.2 18.2 2.3-2.7 1.5 5.3 9.0 ns VIN= 2 x VCC for tPLZ 3.0-3.6 1.5 4.0 7.0 ns VIN = 0V for tPHZ 4.5-5.5 1.5 2.7 5.0 ns Figures 1, 2 Figures 1, 2 Note 8: All typical values are at the specified VCC, and TA = 25°C. Note 9: This parameter is guaranteed by design but is not tested. The switch contributes no propagation delay other than the RC delay of the typical On Resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance). Capacitance Symbol Parameter Typ Max Units Conditions CIN Control Pin Input Capacitance 2 pF VCC = 0V CI/O Input/Output Capacitance 6 pF VCC = 5.0V 3 www.fairchildsemi.com NC7SZ66 AC Electrical Characteristics NC7SZ66 AC Loading and Waveforms Input driven by 50Ω source terminated in 50Ω CL includes load and stray capacitance. Input PRR = 1.0 MHz; tw = 500 ns FIGURE 1. AC Test Circuit FIGURE 2. AC Waveforms www.fairchildsemi.com 4 TAPE FORMAT FOR SOT23, SC70 Package Tape Designator M5X, P5X Number Cavity Section Cavities Status Cover Tape Status Leader (Start End) 125 (typ) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed TAPE DIMENSIONS inches (millimeters) Package SC70-5 SOT23-5 Tape Size 8 mm 8 mm DIM A DIM B 0.093 0.096 (2.35) (2.45) 0.130 0.130 (3.3) (3.3) DIM F DIM Ko 0.138 ± 0.004 0.053 ± 0.004 (3.5 ± 0.10) (1.35 ± 0.10) 0.138 ± 0.002 0.055 ± 0.004 (3.5 ± 0.05) 5 (1.4 ± 0.11) DIM P1 DIM W 0.157 0.315 ± 0.004 (4) (8 ± 0.1) 0.157 0.315 ± 0.012 (4) (8 ± 0.3) www.fairchildsemi.com NC7SZ66 Tape and Reel Specification NC7SZ66 Tape and Reel Specification TAPE FORMAT FOR MicroPak Package Designator L6X (Continued) Tape Number Cavity Section Cavities Status Status Leader (Start End) 125 (typ) Empty Sealed Carrier 5000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed TAPE DIMENSIONS inches (millimeters) www.fairchildsemi.com Cover Tape 6 NC7SZ66 Tape and Reel Specification (Continued) REEL DIMENSIONS inches (millimeters) Tape Size 8 mm A B C D N W1 W2 W3 7.0 0.059 0.512 0.795 2.165 0.331 + 0.059/−0.000 0.567 W1 + 0.078/−0.039 (177.8) (1.50) (13.00) (20.20) (55.00) (8.40 + 1.50/−0.00) (14.40) (W1 + 2.00/−1.00) 7 www.fairchildsemi.com NC7SZ66 Physical Dimensions inches (millimeters) unless otherwise noted 5-Lead SOT23, JEDEC MO-178, 1.6mm Package Number MA05B www.fairchildsemi.com 8 NC7SZ66 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 5-Lead SC70, EIAJ SC-88a, 1.25mm Wide Package Number MAA05A 9 www.fairchildsemi.com NC7SZ66 TinyLogic Low Voltage UHS Single SPST Normally Open Bus Switch Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 6-Lead MicroPak, 1.0mm Wide Package Number MAC06A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com www.fairchildsemi.com 10