DM85 inrush pcb power relay • miniature pcb power relay • Up to 80A inrush (20ms) • AgSnO2 contacts • RoHS Compliant E305753 Contacts Contact number & arrangement SPST-NO (1 N/O) Contact material AgSnO2 Max. switching voltage AC/DC 440VAC Max. breaking capacity AC1 4000VA Min. switching current / voltage Max. inrush current Rated load 10mA/10VDC 80A (20ms) AC1 16A, 250VAC (600 ops/hr) AC15 3A, 120V / 1.5A, 240V (B300) AC3 750W (single phase motor) DC1 16A, 24VDC DC13 0.22A, 120V / 0.1A, 250V (R300) Initial resistance ≤ 100mΩ, max. at 0.1A/24VDC Coil Rated voltage DC 3...110V Must release voltage DC ≥ 0.1Un Operating range of supply voltage Rated power consumption See coil table 1 DC 0.4...0.48mW Insulation (EN 60664-1) Insulation rated voltage AC 400VAC Rated surge voltage 4000V 1.2 / 50 μs Overvoltage category III Insulation pollution degree 3 Dielectric strength coil to contact 5000Vrms, 1min contact to contact 1000Vrms, 1min Contact - coil distance clearance ≥10mm creepage ≥10mm General Data Operating/release time (typical) mS ≤ 8ms/3ms Electrical Life ops >105 (16A 250VAC) (AC1 / DC1 @ 600 ops/hr) Mechanical life ops ≥ 3 x 107 (72000 ops/hr) Dimensions Weight L x W x H 29 x 12.7 x 15.7mm 14g Ambient temperature storage -40 to 85°C operating -40 to 85°C Shock resistance 30g Vibration resistance 10g 10~150Hz Page 1 of 2 www.durakoolrelays.com Ref: DM85 Inrush 090313JHM Sales Department Tel: (888) 847-6552 Specifications are subject to change without notice. E&OE. DM85 inrush pcb power relay Coil Data (DC voltage 400 ...480mW) Table 1 Coil Voltage Code Nominal Voltage (VDC) Coil Resistance (Ω) ±10% Must release voltage min. (VDC) Max. operating voltage (VDC) 1003 3 22 2.1 7.6 1005 5 60 3.5 12.7 1006 6 90 4.2 15.3 1009 9 200 6.3 22.9 1012 12 360 8.4 30.6 1018 18 710 12.6 45.9 1024 24 1440 16.8 61.2 1036 36 3140 25.2 91.8 1048 48 5700 33.6 122.4 1060 60 7500 42.0 153.0 1110 110 25200 77.0 280.0 Note: Parameters at 20°C Ordering codes Contact Material Type D M 8 5 - 5 0 Contact arrangement 2 1 Cover protection and mounting - 2 5 Coil code - Contact material 50 - see Table 1 AgSnO2 Contact arrangement 21 - SPST-NO (1 N/O) Cover protection category 2 - in cover, flux tight - IP40 Connection mode 5 - for PCB Overall Dimensions Fig. 1 Connection diagram Fig. 2 Terminal (Pin) Dimensions Terminal (pin) (mm) Coil A1(1); A2 (2) Contacts 21 (4);11(7); 4(8); 24(5) Ø 0.6 0.5 x 0.9 Drill Hole: Ø 1.3 +0.1mm (Bottom View) (Contact terminals should be tracked as shown above with 14 connected to 24, and 11 connected to 21 on the PCB) Dimensions in mm Page 2 of 2 www.durakoolrelays.com Ref: DM85 Inrush 090313JHM Sales Department Tel: (888) 847-6552 Specifications are subject to change without notice. E&OE.