M54HC4351/52/53 M74HC4351/52/53 ANALOG MULTIPLEXER/DEMULTIPLEXER WITH ADDRESS LATCH: SINGLE 8 CHANNEL, DUAL 4 CHANNEL, TRIPLE 2 CHANNEL . . . .. .. . . . LOGIC LEVEL TRANSLATION TO ENABLE 5V LOGIC SIGNAL TO COMMUNICATE WITH ±5V ANALOG SIGNAL WIDE OPERATING VOLTAGE RANGE (VCC - VEE) 2V TO 12V LOW ”ON” RESISTANCE: 70Ω TYP. (VCC - VEE = 4.5 V) 50Ω TYP. (VCC - VEE = 9 V) WIDE ANALOG INPUT VOLTAGE RANGE: ±6V FAST SWITCHING LOW CROSSTALK BETWEEN SWITCHES HIGH ON/OFF OUTPUT VOLTAGE RATIO LOW SINE WAVE DISTORTION: 0.02% (TYP.) AT VCC - VEE = 9 V HIGH NOISE IMMUNITY VNIH = VNIL = 28% VCC (MIN.) LOW POWER DISSIPATION ICC = 4 µA (MAX) AT TA = 25 oC DESCRIPTION These devices are analog multiplexer demultiplexers in high speed silicon gate C 2MOS technology. These analog switches are bidirectional and digitally controlled. A built-in level shifting is included to allow them a control input range of up to ± 6V (peak) for an analog signal with digital control signal of 0 to 6V. VEE supply pin is provided for analog input signals. They have two enable inputs to enable all the switches when high (EN2) or low (EN1). For operation as a digital multiplexer/demultiplexer, VEE is connected to GND. B1R (Plastic Package) F1R (Ceramic Package) M1R C1R (Micro Package) (Chip Carrier) ORDER CODES : M54HCXXXXF1R M74HCXXXXM1R M74HCXXXXB1R M74HCXXXXC1R The HC4351 is a single 8 channel multiplexer demultiplexer having three binary control inputs A, B and C to select 1 of 8 to be turned on, and connected to the output. The HC4352 has a pair of four channel multiplexer demultiplexer having two control inputs A and B that select one of four channel of the two sections. The HC4353 is a triple two channel multiplexer demultiplexer having three separate digital control inputs A, B and C to select independently one of a pair of channles. PIN CONNECTION (top view) HC4351 November 1993 HC4352 HC4353 1/16 M54/M74HC4351/4352/4353 CHIP CARRIER HC4351 HC4352 PIN DESCRIPTION (HC4351) PIN No 4 3, 14 7 8 SYMBOL COM NC EN1 EN2 9 11 VEE LE 15, 13, 12 17, 18, 19, 16, 1, 6, 2, 5 10 20 A, B, C 0 to 7 GND VCC NAME AND FUNCTION Common Not Connected Enable Input (Active LOW) Enable Input (Active HIGH) Negative Supply Voltage Latch Enable Input (Active LOW) Select Inputs Independent Input/Outputs Ground (0V) Positive Supply Voltage PIN DESCRIPTION (HC4353) PIN No 1, 2 5 6, 4 3, 14 7 8 SYMBOL 0Y 1Y Z COM 0Z, 1Z NC EN1 EN2 9 11 VEE LE 15, 13, 12 16, 17 18 19 10 20 A, B, C 0X, 1X X COM Y COM GND VCC 2/16 NAME AND FUNCTION Independent Input/Outputs Common Output/Inputs Independent Input/Outputs Not Connected Enable Input (Active LOW) Enable Input (Active HIGH) Negative Supply Voltage Latch Enable Input (Active LOW) Select Inputs Independent Input/Outputs Common Output/Inputs Common Output/Inputs Ground (0V) Positive Supply Voltage HC4353 PIN DESCRIPTION (HC4352) PIN No 1, 6, 2, 5 3, 14 7 8 SYMBOL 0Y to 3Y NC EN1 EN2 9 11 V EE LE 13, 12 16, 18, 19, 15 17, 4 A, B 0X to 3X 10 20 X COM Y COM GND VCC NAME AND FUNCTION Independent Input/Outputs Not Connected Enable Input (Active LOW) Enable Input (Active HIGH) Negative Supply Voltage Latch Enable Input (Active LOW) Select Inputs Independent Input/Outputs Common Output/Inputs Ground (0V) Positive Supply Voltage M54/M74HC4351/4352/4353 IEC LOGIC SYMBOLS HC4351 HC4352 HC4353 TRUTH TABLE CONTROL INPUTS ”ON” CHANNEL (LE = H) ** EN1 L L EN2 H H C* L L B L L A L H HC4351 0 1 HC4352 0X, 0Y 1X, 1Y HC4353 0X, 0Y, 0Z 1X, 0Y, 0Z L H L L L H H L H H L 2 2X, 2Y 0X, 1Y, 0Z H L H L 3 4 3X, 3Y -- 1X, 1Y, 0Z 0X, 0Y, 1Z L H L L H H H X H L H 5 -- 1X, 0Y, 1Z H H X H H X L H X 6 7 NONE --NONE 0X, 1Y, 1Z 1X, 1Y, 1Z NONE X L X X X NONE NONE NONE X: DON’T CARE *: HC4351/3 only ** When latch Enable is low, the Channel Selection is latched and the Channel Address Latch does not change state. 3/16 M54/M74HC4351/4352/4353 ABSOLUTE MAXIMUM RATINGS Symbol VCC VCC - VEE Parameter Supply Voltage Range Supply Voltage Range VIN DC Input Voltage VI/O IIK DC Switch I/O Voltage Input Diode Current IOK IOUT ICC or IGND Value Unit -0.5 to +7 -0.5 to 13 V V -0.5 to VCC + 0.5 V VEE - 0.5 to VCC + 0.5 ± 20 V mA I/O Diode Current ± 20 mA DC Output Current ± 25 mA DC VCC or Ground Current ± 50 mA 500 (*) -65 to +150 mW o C PD Tstg Power Dissipation Storage Temperature TL Lead Temperature (10 sec) 300 o C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied. (*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC RECOMMENDED OPERATING CONDITIONS Symbol VCC Supply Voltage Value 2 to 6 Unit V VEE Supply Voltage -6 to 0 V VCC - VEE VIN Supply Voltage Input Voltage 2 to 12 0 to VCC V V VI/O Parameter DC Switch I/O Voltage Top Operating Temperature: tr, tf Input Rise and Fall Time 4/16 M54HC Series M74HC Series VEE to V CC V -55 to +125 -40 to +85 o VCC = 2 V VCC = 4.5 V 0 to 1000 0 to 500 VCC = 6 V 0 to 400 o C C ns M54/M74HC4351/4352/4353 DC SPECIFICATIONS Test Conditions Symbol VIHC V ILC RON Parameter VCC (V) VEE (V) 2.0 1.5 1.5 1.5 4.5 6.0 3.15 4.2 3.15 4.2 3.15 4.2 Low Level Control Input Voltage 2.0 0.5 0.5 0.5 4.5 1.35 1.35 1.35 1.8 ON Resistance 4.5 GND 6.0 -4.5 -6.0 2.0 GND 4.5 GND 4.5 6.0 IOFF IIZ IIN ICC -40 to 85 oC -55 to 125 oC Unit 74HC 54HC Min. Max. Min. Max. High Level Control Input Voltage 4.5 6.0 ∆RON Value TA = 25 oC 54HC and 74HC Min. Typ. Max. Difference of ON Resistance Between Switches Input/Output Leakage Current (SWITCH OFF) Switch Input Leakage Current (SWITCH ON) Control Input Current Quiescent Supply Current -4.5 -6.0 4.5 GND 4.5 -4.5 6.0 -6.0 6.0 -6.0 6.0 -6.0 6.0 GND 6.0 GND 6.0 -6.0 1.8 1.8 VIN = VIHC or VILC VI/O = VCC to VEE II/O ≤ 2 mA 85 180 225 55 50 120 100 150 125 VIN = VIHC or VILC VI/O = VCC or VEE II/O ≤ 2 mA 150 VIN = VIHC or VILC VI/O = VCC to VEE II/O ≤ 2 mA VOS = VCC or GND VIS = GND or VCC VIN = VILC VOS = VCC or GND VINH = VIHC VIN = V CC or GND VIN = V CC or GND V V Ω 70 150 190 50 45 100 80 125 100 10 5 30 12 35 15 5 10 12 ±100 ±1000 ± nA ±100 ±1000 ± nA ±0.1 ±1 ±1 µA 4 40 80 µA 8 80 160 Ω 5/16 M54/M74HC4351/4352/4353 AC ELECTRICAL CHARACTERISTICS for HC4351 (C L = 50 pF, Input tr = tf = 6 ns, GND=0V) Test Conditions Symbol Parameter VCC (V) VEE (V) ΦI/O Phase Difference Between Input and Output 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 tPZL tPZH Output Enable Time (E1, E2 - O) tPZL tPZH Output Enable Time (LE - I/O) tPZL tPZH Output Enable Time (A, B, C - I/O) tPLZ tPHZ Output Disable Time (E1, E2 - O) tPLZ tPHZ Output Disable Time (LE - I/O) tPLZ tPHZ Output Disable Time (A, B, C - I/O) tW(H) Minimum Pulse Width (LE) ts th CIN CIS COS CIOS CPD (*) Minimum Set Up Time Minimum Hold Time Input Capacitance Common Terminal Capacitance Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance 5.0 -5.0 5.0 -5.0 5.0 -5.0 5.0 GND RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ TA = 25 oC 54HC and 74HC Min. Typ. Max. 25 60 6 12 5 10 4 80 200 20 40 16 34 18 80 225 22 45 17 38 18 75 225 22 45 16 38 17 120 275 38 55 33 47 30 120 275 40 55 35 47 34 120 290 40 58 35 49 35 75 15 13 50 10 9 5 5 5 5 10 36 70 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 75 15 13 ns 250 50 43 300 60 51 ns 280 56 48 340 68 57 ns 280 56 48 340 68 57 ns 344 69 59 415 83 71 ns 344 69 59 415 83 71 ns 363 73 61 433 87 74 ns 95 19 16 60 12 11 5 5 5 10 70 110 22 19 75 15 13 5 5 5 10 70 7 15 15 15 0.95 2 2 2 23 Unit ns ns ns pF pF pF pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC 6/16 M54/M74HC4351/4352/4353 AC ELECTRICAL CHARACTERISTICS for HC4352 (C L = 50 pF, Input tr = tf = 6 ns, GND=0V) Test Conditions Symbol Parameter VCC (V) VEE (V) ΦI/O Phase Difference Between Input and Output 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 tPZL tPZH Output Enable Time (E1, E2 - O) tPZL tPZH Output Enable Time (LE - I/O) tPZL tPZH Output Enable Time (A, B, C - I/O) tPLZ tPHZ Output Disable Time (E1, E2 - O) tPLZ tPHZ Output Disable Time (LE - I/O) tPLZ tPHZ Output Disable Time (A, B, C - I/O) tW(H) Minimum Pulse Width (LE) ts th CIN CIS COS CIOS CPD (*) Minimum Set Up Time Minimum Hold Time Input Capacitance Common Terminal Capacitance Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance 5.0 -5.0 5.0 -5.0 5.0 -5.0 5.0 GND RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ TA = 25 oC 54HC and 74HC Min. Typ. Max. 25 60 6 12 5 10 4 80 200 20 40 16 34 18 80 225 22 45 17 38 18 80 225 22 45 16 38 17 120 275 38 55 33 47 36 160 275 40 55 34 47 32 120 275 40 55 35 47 31 75 15 13 50 10 9 5 5 5 5 10 19 40 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 75 15 13 ns 250 50 43 300 60 51 ns 280 56 48 340 68 57 ns 280 56 48 340 68 57 ns 344 69 59 415 83 71 ns 344 69 59 415 83 71 ns 344 69 59 415 83 71 ns 95 19 16 60 12 11 5 5 5 10 40 110 22 19 75 15 13 5 5 5 10 40 7 15 15 15 0.85 2 2 2 34 Unit ns ns ns pF pF pF pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC 7/16 M54/M74HC4351/4352/4353 AC ELECTRICAL CHARACTERISTICS for HC4353 (C L = 50 pF, Input tr = tf = 6 ns, GND=0V) Test Conditions Symbol Parameter VCC (V) VEE (V) ΦI/O Phase Difference Between Input and Output 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 4.5 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 GND GND GND -4.5 tPZL tPZH Output Enable Time (E1, E2 - O) tPZL tPZH Output Enable Time (LE - I/O) tPZL tPZH Output Enable Time (A, B, C - I/O) tPLZ tPHZ Output Disable Time (E1, E2 - O) tPLZ tPHZ Output Disable Time (LE - I/O) tPLZ tPHZ Output Disable Time (A, B, C - I/O) tW(H) Minimum Pulse Width (LE) ts th CIN CIS COS CIOS CPD (*) Minimum Set Up Time Minimum Hold Time Input Capacitance Common Terminal Capacitance Switch Terminal Capacitance Feed Through Capacitance Power Dissipation Capacitance 5.0 -5.0 5.0 -5.0 5.0 -5.0 5.0 GND RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ RL = 1KΩ TA = 25 oC 54HC and 74HC Min. Typ. Max. 25 60 6 12 5 10 4 100 200 22 40 18 34 19 110 225 24 45 20 38 18 100 225 22 45 18 38 19 130 290 38 58 32 49 30 140 300 41 60 34 51 37 135 325 42 65 32 55 35 75 15 13 50 10 9 5 5 5 5 10 11 20 Value -40 to 85 oC -55 to 125 oC 74HC 54HC Min. Max. Min. Max. 75 15 13 ns 250 50 43 300 60 51 ns 280 56 48 340 68 57 ns 280 56 48 340 68 57 ns 363 72 61 435 87 74 ns 375 75 64 450 90 77 ns 406 81 69 100 85 ns 95 19 16 60 12 11 5 5 5 10 20 110 22 19 75 15 13 5 5 5 10 20 7 15 15 15 0.75 2 2 2 10 Unit ns ns ns pF pF pF pF pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC 8/16 M54/M74HC4351/4352/4353 ANALOG SWITCH CHARACTERISTICS (GND = 0 V T A = 25 o C) Test Conditions Symbol Parameter Sine Wave Distortion fMAX VCC VEE VIN (V) (V) (Vp-p) 2.25 -2.25 4 4.5 -4.5 Frequency Response (Switch ON) 4.5 -4.5 Feedthrough Attenuation (Switch OFF) 2.25 -2.25 4.5 -4.5 6 -6 6.0 6 fIN = 1 KHz RL = 10 Ω CL = 50 pF 0.025 0.02 % Adjust fIN voltage to Obtain 0 dBm at VOS. Increase fIN Frequency until dB Meter Reads -3dB CL = 10 pF (*) RL = 50 Ω 200 MHz VIN is centered at (VCC - VEE)/2. Adjust input for 0 dBm RL = 600 Ω CL = 50 pF fIN = 1 MHz sine wave -50 -50 dB tr = tf = 6ns RL = 600 Ω CL = 50 pF fIN = 1 MHz square wave -6.0 2.25 -2.25 4.5 -4.5 Unit Typ. 8 Crosstalk 2.25 -2.25 Control to switch 4.5 -4.5 Crosstalk Between any two switches Value Adjust VIN to obtain 0dBm at input RL = 600 Ω CL = 50 pF fIN = 1 MHz sine wave -6 -50 110 225 mV 310 -50 -50 dB -50 (*): Input COMMON Terminal, and measured at SWITCH Terminal. NOTE: These characteristics are determined by design of devices. 9/16 M54/M74HC4351/4352/4353 SWITCHING CHARACTERISTICS TEST CIRCUIT tPLZ, tPHZ, tPZL, tPZH. CROSSTALK (control to output) BANDWIDTH AND FEEDTHROUGH ATTENUATION CROSSTALK BETWEEN ANY TWO SWITCHES GND (VSS) CI–O CI/O GND (VSS) 10/16 M54/M74HC4351/4352/4353 SWITCHING CHARACTERISTICS TEST WAVEFORM tPLZ, tPHZ, tPZL, tPZH. CHANNEL RESISTANCE (RON) ts, th, tw I CC (Opr.) 11/16 M54/M74HC4351/4352/4353 Plastic DIP20 (0.25) MECHANICAL DATA mm DIM. MIN. a1 0.254 B 1.39 TYP. inch MAX. MIN. TYP. MAX. 0.010 1.65 0.055 0.065 b 0.45 0.018 b1 0.25 0.010 D 25.4 1.000 E 8.5 0.335 e 2.54 0.100 e3 22.86 0.900 F 7.1 0.280 I 3.93 0.155 L Z 3.3 0.130 1.34 0.053 P001J 12/16 M54/M74HC4351/4352/4353 Ceramic DIP20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 25 0.984 B 7.8 0.307 D E 3.3 0.5 e3 0.130 1.78 0.020 22.86 0.070 0.900 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 I 1.27 1.52 0.050 0.060 L 0.22 0.31 0.009 0.012 M 0.51 1.27 0.020 0.050 N1 P Q 4° (min.), 15° (max.) 7.9 8.13 5.71 0.311 0.320 0.225 P057H 13/16 M54/M74HC4351/4352/4353 SO20 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 2.65 0.10 0.104 0.20 a2 MAX. 0.004 0.007 2.45 0.096 b 0.35 0.49 0.013 0.019 b1 0.23 0.32 0.009 0.012 C 0.50 0.020 c1 45° (typ.) D 12.60 13.00 0.496 0.512 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 F 7.40 7.60 0.291 0.299 L 0.50 1.27 0.19 0.050 M S 0.75 0.029 8° (max.) P013L 14/16 M54/M74HC4351/4352/4353 PLCC20 MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. MAX. A 9.78 10.03 0.385 0.395 B 8.89 9.04 0.350 0.356 D 4.2 4.57 0.165 0.180 d1 2.54 0.100 d2 0.56 0.022 E 7.37 8.38 0.290 0.330 e 1.27 0.050 e3 5.08 0.200 F 0.38 0.015 G 0.101 0.004 M 1.27 0.050 M1 1.14 0.045 P027A 15/16 M54/M74HC4351/4352/4353 Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 16/16