19-4099; Rev 0; 4/08 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors Features The MAX16060/MAX16061/MAX16062 are 1% accurate, quad-/hex-/octal-voltage µP supervisors in a small thin QFN package. These devices provide supervisory functions for complex multivoltage systems. The MAX16060 monitors four voltages, the MAX16061 monitors six voltages, and the MAX16062 monitors eight voltages. These devices offer independent outputs for each monitored voltage along with a reset output that asserts whenever any of the monitored voltages fall below their respective thresholds (down to 0.4V) or the manual reset input is asserted. The reset output remains asserted for the reset timeout after all voltages are above their respective thresholds and the manual reset input is deasserted. The minimum reset timeout is internally set to 140ms or can be adjusted with an external capacitor. o Fixed Thresholds for 3.3V, 2.5V, and 1.8V Systems o Adjustable Thresholds Monitor Low Voltages (Down to 0.4V) o 1% Accurate over Temperature o Open-Drain Outputs with Internal Pullups Reduce the Number of External Components o Fixed 140ms (min) or Capacitor-Adjustable Reset Timeout o Manual Reset, Margin Enable, and Tolerance Select Inputs o Watchdog Timer 1.6s (typ) Timeout Period 54s Startup Delay After Reset o Monitors Four (MAX16060), Six (MAX16061), or Eight (MAX16062) Voltages o RESET Output Indicates All Voltages Present o Independent Voltage Monitors o Guaranteed to Remain Asserted Down to VCC = 1V o Small (4mm x 4mm) Thin QFN Package All open-drain outputs have internal 30µA pullups that eliminate the need for external pullup resistors. However, each output can be driven with an external voltage up to 5.5V. Other features offered include a manual reset input, a tolerance pin for selecting 5% or 10% input thresholds, and a margin enable function for deasserting the outputs during margin testing. An additional feature is a watchdog timer that asserts RESET when the watchdog timeout period (1.6s typ) is exceeded. The watchdog timer can be disabled by leaving WDI unconnected. These devices are offered in 16-, 20-, and 24-pin thin QFN packages (4mm x 4mm) and are fully specified from -40°C to +125°C. Ordering Information PART TEMP RANGE PIN-PACKAGE MAX16060_TE+ -40°C to +125°C 16 TQFN-EP* MAX16061_TP+ -40°C to +125°C 20 TQFN-EP* MAX16062_TG+ -40°C to +125°C 24 TQFN-EP* Note: The “_” is a placeholder for the input voltage threshold. See Table 1. The MAX16060/MAX16061/MAX16062 are available in factory-preset thresholds/configuration combinations. Choose the desired combination and complete part number from Table 1. +Denotes a lead-free package. For tape-and-reel, add a “T” after the “+.” Tape-and-reel are offered in 2.5k increments. *EP = Exposed pad. Applications Storage Equipment Multivoltage ASICs Servers Automotive Networking/Telecommunication Equipment Typical Operating Circuit VIN1 VCC IN1 VIN2 IN2 VIN3 IN3 SRT MARGIN RESET RST μP WDI I/O MAX16061A VIN4 IN4 VIN5 IN5 OUT1 OUT2 OUT3 VIN6 OUT4 IN6 OUT5 OUT6 MR GND TOL ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX16060/MAX16061/MAX16062 General Description MAX16060/MAX16061/MAX16062 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors ABSOLUTE MAXIMUM RATINGS VCC, OUT_, IN_, RESET to GND ..............................-0.3V to +6V TOL, MARGIN, MR, SRT, WDI to GND ...........-0.3V to VCC + 0.3 Input/Output Current (RESET, MARGIN, SRT, MR, TOL, OUT_, WDI).........................................±20mA Continuous Power Dissipation (TA = +70°C) 16-Pin TQFN (derate 16.9mW/°C above +70°C) ......1349mW 20-Pin TQFN (derate 16.9mW/°C above +70°C) ......1355mW 24-Pin TQFN (derate 16.9mW/°C above +70°C) ......1666mW Operating Temperature Range .........................-40°C to +125°C Junction Temperature .....................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = 2.0V to 5.5V, TA = -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V, TA = +25°C.) (Note 1) PARAMETER SYMBOL Operating Voltage Range VCC Supply Current (Note 3) ICC UVLO (Undervoltage Lockout) UVLO Hysteresis VUVLO CONDITIONS (Note 2) MIN TYP 1.0 MAX UNITS 5.5 V VCC = 3.3V, OUT_, RESET not asserted 45 65 VCC = 5V, OUT_, RESET not asserted 50 70 1.80 1.98 VCC rising 1.62 VUVLO_HYS 65 µA V mV IN_ (See Table 1) 3.3V threshold, TOL = GND Threshold Voltages (IN_ Falling) Adjustable Threshold (IN_ Falling) IN_ Hysteresis IN_ Input Current 2 VTH VTH VTH_HYS 3.069 3.102 3.135 3.3V threshold, TOL = VCC 2.904 2.937 2.970 2.5V threshold, TOL = GND 2.325 2.350 2.375 2.5V threshold, TOL = VCC 2.200 2.225 2.250 1.8V threshold, TOL = GND 1.674 1.692 1.710 1.8V threshold, TOL = VCC 1.584 1.602 1.620 TOL = GND 0.390 0.394 0.398 TOL = VCC 0.369 0.373 0.377 IN_ rising 0.5 Fixed thresholds Adjustable thresholds 3 -100 _______________________________________________________________________________________ V V % VTH 16 µA +100 nA 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors (VCC = 2.0V to 5.5V, TA = -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V, TA = +25°C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS RESET Reset Timeout tRP SRT = VCC 140 200 280 CSRT = 1500pF (Note 4) 2.43 3.09 3.92 ms nA CSRT = 100pF 0.206 CSRT = open SRT Ramp Current ISRT VSRT = 0V SRT Threshold 50 600 740 1.173 1.235 1.293 SRT Hysteresis IN_ to Reset Delay tRD RESET Output-Voltage Low VOL RESET Output-Voltage High VOH MR Input-Voltage Low VIL MR Input-Voltage High VIH IN_ falling mV 20 µs 0.3 VCC = 2.5V, ISINK = 6mA, RESET asserted 0.3 VCC = 1.2V, ISINK = 50µA, RESET asserted 0.3 VCC ≥ 2.0V, ISOURCE = 6µA, RESET deasserted 0.8 x VCC V V 0.3 x VCC V 0.7 x VCC V 1 µs MR Glitch Rejection 100 MR to Reset Delay 200 Pulled up to VCC V 100 VCC = 3.3V, ISINK = 10mA, RESET asserted MR Minimum Pulse Width MR Pullup Resistance µs 460 12 20 ns ns 28 kΩ OUTPUTS (OUT_ ) OUT_ Output-Voltage Low VOL OUT_ Output-Voltage High VOH IN_ to OUT_ Propagation Delay tD VCC = 3.3V, ISINK = 2mA 0.3 VCC = 2.5V, ISINK = 1.2mA 0.3 VCC ≥ 2.0V, ISOURCE = 6µA (VTH + 100mV) to (VTH - 100mV) 0.8 x VCC V V 20 µs _______________________________________________________________________________________ 3 MAX16060/MAX16061/MAX16062 ELECTRICAL CHARACTERISTICS (continued) MAX16060/MAX16061/MAX16062 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors ELECTRICAL CHARACTERISTICS (continued) (VCC = 2.0V to 5.5V, TA = -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V, TA = +25°C). (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 0.3 x VCC V WATCHDOG TIMER WDI Input-Voltage Low VIL WDI Input-Voltage High VIH WDI Pulse Width Watchdog Timeout Period 0.7 x VCC (Note 5) tWDI Watchdog Startup Period Watchdog Input Current VWDI = 0 to VCC (Note 5) V 50 ns 1.12 1.60 2.40 s 35 54 72 s +1 µA 0.3 x VCC V -1 DIGITAL LOGIC TOL Input-Voltage Low VIL TOL Input-Voltage High VIH TOL Input Current V TOL = VCC MARGIN Input-Voltage Low VIL MARGIN Input-Voltage High VIH MARGIN Pullup Resistance MARGIN Delay Time 0.7 x VCC nA V 0.7 x VCC Pulled up to VCC tMD 100 0.3 x VCC Rising or falling (Note 6) 12 V 20 50 28 kΩ µs Note 1: Devices are tested at TA = +25°C and guaranteed by design for TA = TMIN to TMAX. Note 2: The outputs are guaranteed to remain asserted down to VCC = 1V. Note 3: Measured with WDI, MARGIN, and MR unconnected. Note 4: The minimum and maximum specifications for this parameter are guaranteed by using the worst case of the SRT ramp current and SRT threshold specifications. Note 5: Guaranteed by design and not production tested. Note 6: Amount of time required for logic to lock/unlock outputs from margin testing. 4 _______________________________________________________________________________________ 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors 45 40 VCC = 5V 50 45 VCC = 3.3V 40 VCC = 2.5V 35 35 1.5 2.0 2.5 3.0 3.5 4.0 4.5 SUPPLY VOLTAGE (V) 5.0 1.0025 1.0000 0.9975 0.9950 0.9900 1.5 VOUT_ (mV) 50 0.997 25 600 400 OUT_ LOW 0 2 3 4 5 6 SINK CURRENT (mA) 7 0 8 400 300 200 100 197 196 5 10 15 20 SOURCE CURRENT (μA) 25 30 RESET TIMEOUT DELAY MAX16060/1/2 toc09 MAX16060/1/2 toc08 OUTPUT GOES LOW ABOVE THIS LINE 500 198 RESET TIMEOUT PERIOD (ms) MAX16060/1/2 toc07 600 1 RESET TIMEOUT PERIOD vs. TEMPERATURE MAXIMUM TRANSIENT DURATION vs. INPUT OVERDRIVE MAXIMUM TRANSIENT DURATION (μs) OUT_ HIGH 0 0 -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 5.5 200 0.996 0.995 5.0 800 VCC - VOUT_ (mV) 75 0.998 2.5 3.0 3.5 4.0 4.5 SUPPLY VOLTAGE (V) 1000 MAX16060/1/2 toc05 100 0.999 2.0 OUTPUT VOLTAGE vs. SOURCE CURRENT OUTPUT VOLTAGE vs. SINK CURRENT MAX16060/1/2 toc04 NORMALIZED THRESHOLD 1.000 1.0050 -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 5.5 NORMALIZED THRESHOLD vs. TEMPERATURE 1.001 1.0075 0.9925 30 30 MAX16060/1/2 toc03 55 1.0100 MAX16060/1/2 toc06 50 WDI, MARGIN, AND MR UNCONNECTED NORMALIZED THRESHOLD SUPPLY CURRENT (μA) 55 60 MAX16060/1/2 toc02 WDI, MARGIN, AND MR UNCONNECTED SUPPLY CURRENT (μA) MAX16060/1/2 toc01 60 NORMALIZED THRESHOLD vs. SUPPLY VOLTAGE SUPPLY CURRENT vs. TEMPERATURE SUPPLY CURRENT vs. SUPPLY VOLTAGE IN1 5V/div 195 OUT1 2V/div 194 193 192 RESET 2V/div 191 SRT = VCC 190 0 1 10 100 INPUT OVERDRIVE (mV) 1000 MAX16060/MAX16061/MAX16062 Typical Operating Characteristics (VCC = 3.3V, TA = +25°C, unless otherwise noted.) -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) 40ms/div _______________________________________________________________________________________ 5 Typical Operating Characteristics (continued) (VCC = 3.3V, TA = +25°C, unless otherwise noted.) WATCHDOG TIMEOUT PERIOD vs. TEMPERATURE RESET TIMEOUT PERIOD vs. CSRT 10 1 0.1 MAX16060/1/2 toc11 100 1.60 1.59 WATCHDOG TIMEOUT PERIOD (s) MAX16060/1/2 toc10 1000 tRP (ms) MAX16060/MAX16061/MAX16062 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors 1.58 1.57 1.56 1.55 1.54 1.53 1.52 1.51 1.50 0.01 0.01 0.1 1 10 100 1000 CSRT (nF) -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (°C) MARGIN DISABLE FUNCTION MARGIN ENABLE FUNCTION MAX16060/1/2 toc13 MAX16060/1/2 toc12 OUT_ AND RESET ARE BELOW RESPECTIVE THRESHOLDS 100μs/div 6 MARGIN 2V/div MARGIN 2V/div OUT_ 2V/div OUT_ 2V/div RESET 2V/div RESET 2V/div OUT_ AND RESET ARE BELOW RESPECTIVE THRESHOLDS 100μs/div _______________________________________________________________________________________ 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors PIN NAME 1 IN3 Monitored Input Voltage 3. See Table 1 for the input voltage threshold. FUNCTION 2 IN4 Monitored Input Voltage 4. See Table 1 for the input voltage threshold. 3 WDI Watchdog Timer Input. If WDI remains low or high for longer than the watchdog timeout period, RESET is asserted. The timer clears whenever a reset is asserted or a rising or falling edge on WDI is detected. The watchdog timer enters a startup period that allows 54s for the first transition to occur before a reset. Leave WDI unconnected to disable the watchdog timer. The WDI unconnected-state detector uses a small 400nA current. Therefore, do not connect WDI to anything that will source or sink more than 200nA. Note that the leakage current specification for most three-state drivers exceeds 200nA. 4 GND Ground 5 VCC Unmonitored Power-Supply Input 6 OUT3 Output 3. When the voltage at IN3 falls below its threshold, OUT3 goes low and stays low until the voltage at IN3 exceeds its threshold. The open-drain output has a 30µA internal pullup to V CC . 7 OUT4 Output 4. When the voltage at IN4 falls below its threshold, OUT4 goes low and stays low until the voltage at IN4 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 8 MR Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET remains low for the reset timeout period after MR is deasserted. MR is pulled up to VCC through a 20kΩ resistor. 9 SRT Set Reset Timeout Input. Connect a capacitor from SRT to GND to set the reset timeout period. The reset timeout period can be calculated as follows: Reset Timeout (s) = 2.06 x 106 (Ω) x CSRT (F). For the internal timeout period of 140ms (min), connect SRT to VCC. 10 MARGIN 11 OUT2 Output 2. When the voltage at IN2 falls below its threshold, OUT2 goes low and stays low until the voltage at IN2 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 12 OUT1 Output 1. When the voltage at IN1 falls below its threshold, OUT1 goes low and stays low until the voltage at IN1 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 13 RESET Active-Low Reset Output. RESET asserts low when any of the monitored voltages falls below its respective threshold or MR is asserted. RESET remains asserted for the reset timeout period after all monitored voltages exceed their respective thresholds and MR is deasserted. This open-drain output has a 30µA internal pullup. 14 IN1 Monitored Input Voltage 1. See Table 1 for the input voltage threshold. 15 IN2 Monitored Input Voltage 2. See Table 1 for the input voltage threshold. 16 TOL Threshold Tolerance Input. Connect TOL to GND to select 5% threshold tolerance. Connect TOL to VCC to select 10% threshold tolerance. — EP Exposed Pad. EP is internally connected to GND. Connect EP to the ground plane to provide a low thermal resistance path from the IC junction to the PCB. Do not use as the electrical connection to GND. Active-Low Manual Deassert Input. Pull MARGIN low to deassert all outputs (go into high state), regardless of the voltage at any monitored input. _______________________________________________________________________________________ 7 MAX16060/MAX16061/MAX16062 Pin Description (MAX16060) 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors MAX16060/MAX16061/MAX16062 Pin Description (MAX16061) 8 PIN NAME 1 IN4 Monitored Input Voltage 4. See Table 1 for the input voltage threshold. FUNCTION 2 IN5 Monitored Input Voltage 5. See Table 1 for the input voltage threshold. 3 IN6 Monitored Input Voltage 6. See Table 1 for the input voltage threshold. 4 WDI Watchdog Timer Input. If WDI remains low or high for longer than the watchdog timeout period, RESET is asserted and the timer is cleared. The timer also clears whenever a reset is asserted or a rising or falling edge on WDI is detected. The watchdog timer enters a startup period that allows 54s for the first transition to occur before a reset. Leave WDI unconnected to disable the watchdog timer. The WDI unconnected-state detector uses a small 400nA current. Therefore, do not connect WDI to anything that will source or sink more than 200nA. Note that the leakage current specification for most three-state drivers exceeds 200nA. 5 GND Ground 6 VCC Unmonitored Power-Supply Input 7 OUT4 Output 4. When the voltage at IN4 falls below its threshold, OUT4 goes low and stays low until the voltage at IN4 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 8 OUT5 Output 5. When the voltage at IN5 falls below its threshold, OUT5 goes low and stays low until the voltage at IN5 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 9 OUT6 Output 6. When the voltage at IN6 falls below its threshold, OUT6 goes low and stays low until the voltage at IN6 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 10 MR Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET remains low for the reset timeout period after MR is deasserted. MR is pulled up to VCC through a 20kΩ resistor. 11 SRT Set Reset Timeout Input. Connect a capacitor from SRT to GND to set the reset timeout period. The reset timeout period can be calculated as follows: Reset Timeout (s) = 2.06 x 106 (Ω) x CSRT (F). For the internal timeout period of 140ms (min), connect SRT to VCC. 12 MARGIN Manual Deassert Input. Pull MARGIN low to deassert all outputs (go into high state), regardless of the voltage at any monitored input. 13 OUT3 Output 3. When the voltage at IN3 falls below its threshold, OUT3 goes low and stays low until the voltage at IN3 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 14 OUT2 Output 2. When the voltage at IN2 falls below its threshold, OUT2 goes low and stays low until the voltage at IN2 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 15 OUT1 Output 1. When the voltage at IN1 falls below its threshold, OUT1 goes low and stays low until the voltage at IN1 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. 16 RESET Active-Low Reset Output. RESET asserts low when any of the monitored voltages falls below its respective threshold or MR is asserted. RESET remains asserted for the reset timeout period after all monitored voltages exceed their respective thresholds and MR is deasserted. This open-drain output has a 30µA internal pullup. 17 IN1 Monitored Input Voltage 1. See Table 1 for the input voltage threshold. 18 IN2 Monitored Input Voltage 2. See Table 1 for the input voltage threshold. 19 IN3 Monitored Input Voltage 3. See Table 1 for the input voltage threshold. 20 TOL Threshold Tolerance Input. Connect TOL to GND to select 5% threshold tolerance. Connect TOL to VCC to select 10% threshold tolerance. — EP Exposed Pad. EP is internally connected to GND. Connect EP to the ground plane to provide a low thermal resistance path from the IC junction to the PCB. Do not use as the electrical connection to GND. _______________________________________________________________________________________ 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors PIN NAME 1 IN5 Monitored Input Voltage 5. See Table 1 for the input voltage threshold. FUNCTION 2 IN6 Monitored Input Voltage 6. See Table 1 for the input voltage threshold. 3 IN7 Monitored Input Voltage 7. See Table 1 for the input voltage threshold. 4 IN8 Monitored Input Voltage 8. See Table 1 for the input voltage threshold. 5 WDI Watchdog Timer Input. If WDI remains low or high for longer than the watchdog timeout period, RESET is asserted and the timer is cleared. The timer also clears whenever a reset is asserted or a rising or falling edge on WDI is detected. The watchdog timer enters a startup period that allows 54s for the first transition to occur before a reset. Leave WDI unconnected to disable the watchdog timer. The WDI unconnected state detector uses a small 400nA current. Therefore, do not connect WDI to anything that will source or sink more than 200nA. Note that the leakage current specification for most three-state drivers exceeds 200nA. 6 GND Ground 7 VCC Unmonitored Power-Supply Input 8 OUT5 9 OUT6 10 OUT7 11 OUT8 12 MR 13 SRT 14 MARGIN 15 OUT4 16 OUT3 17 OUT2 18 OUT1 19 RESET 20 IN1 Monitored Input Voltage 1. See Table 1 for the input voltage threshold. 21 IN2 Monitored Input Voltage 2. See Table 1 for the input voltage threshold. 22 IN3 Monitored Input Voltage 3. See Table 1 for the input voltage threshold. 23 IN4 Monitored Input Voltage 4. See Table 1 for the input voltage threshold. 24 TOL — EP Output 5. When the voltage at IN5 falls below its threshold, OUT5 goes low and stays low until the voltage at IN5 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. Output 6. When the voltage at IN6 falls below its threshold, OUT6 goes low and stays low until the voltage at IN6 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. Output 7. When the voltage at IN7 falls below its threshold, OUT7 goes low and stays low until the voltage at IN7 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. Output 8. When the voltage at IN8 falls below its threshold, OUT8 goes low and stays low until the voltage at IN8 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET remains low for the reset timeout period after MR is deasserted. MR is pulled up to VCC through a 20kΩ resistor. Set Reset Timeout Input. Connect a capacitor from SRT to GND to set the reset timeout period. The reset timeout period can be calculated as follows: Reset Timeout (s) = 2.06 x 106 (Ω) x CSRT (F). For the internal timeout period of 140ms (min), connect SRT to VCC. Margin Disable Input. Pull MARGIN low to deassert all outputs (go into high state), regardless of the voltage at any monitored input. Output 4. When the voltage at IN4 falls below its threshold, OUT4 goes low and stays low until the voltage at IN4 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. Output 3. When the voltage at IN3 falls below its threshold, OUT3 goes low and stays low until the voltage at IN3 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. Output 2. When the voltage at IN2 falls below its threshold, OUT2 goes low and stays low until the voltage at IN2 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. Output 1. When the voltage at IN1 falls below its threshold, OUT1 goes low and stays low until the voltage at IN1 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC. Active-Low Reset Output. RESET asserts low when any of the monitored voltages falls below its respective threshold or MR is asserted. RESET remains asserted for the reset timeout period after all monitored voltages exceed their respective thresholds and MR is deasserted. This open-drain output has a 30µA internal pullup. Threshold Tolerance Input. Connect TOL to GND to select 5% threshold tolerance. Connect TOL to VCC to select 10% threshold tolerance. Exposed Pad. EP is internally connected to GND. Connect EP to the ground plane to provide a low thermal resistance path from the IC junction to the PCB. Do not use as the electrical connection to GND. _______________________________________________________________________________________ 9 MAX16060/MAX16061/MAX16062 Pin Description (MAX16062) MAX16060/MAX16061/MAX16062 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors Table 1. Input-Voltage-Threshold Selector PART IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 MAX16060A 3.3 2.5 ADJ 1.8 — — — — MAX16060B 3.3 ADJ ADJ 1.8 — — — — MAX16060C ADJ 2.5 ADJ 1.8 — — — — MAX16060D 3.3 2.5 ADJ ADJ — — — — MAX16060E ADJ ADJ ADJ ADJ — — — — MAX16061A 3.3 2.5 ADJ 1.8 ADJ ADJ — — MAX16061B 3.3 ADJ ADJ 1.8 ADJ ADJ — — MAX16061C 3.3 2.5 ADJ ADJ ADJ ADJ — — MAX16061D ADJ 2.5 ADJ 1.8 ADJ ADJ — — MAX16061E ADJ ADJ ADJ ADJ ADJ ADJ — — MAX16062A 3.3 2.5 ADJ 1.8 ADJ ADJ ADJ ADJ MAX16062B 3.3 ADJ ADJ 1.8 ADJ ADJ ADJ ADJ MAX16062C 3.3 2.5 ADJ ADJ ADJ ADJ ADJ ADJ MAX16062D ADJ 2.5 ADJ 1.8 ADJ ADJ ADJ ADJ MAX16062E ADJ ADJ ADJ ADJ ADJ ADJ ADJ ADJ Note: Other fixed thresholds may be available. Contact factory for availability. 10 ______________________________________________________________________________________ 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors WDI MR SRT VCC VCC WATCHDOG TIMER CIRCUIT TIMING RESET CIRCUIT RESET IN1 OUT1 IN2 OUT2 OUTPUT DRIVER IN3 OUT3 EN OUT4 IN4 VCC TOL VCC REFERENCE UNDERVOLTAGE LOCKOUT MAX16060D VCC MARGIN Figure 1. MAX16060D Functional Diagram ______________________________________________________________________________________ 11 MAX16060/MAX16061/MAX16062 Functional Diagrams MAX16060/MAX16061/MAX16062 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors Functional Diagrams (continued) WDI MR SRT VCC VCC WATCHDOG TIMER CIRCUIT TIMING RESET CIRCUIT RESET IN1 OUT1 IN2 OUT2 IN3 OUT3 OUTPUT DRIVER IN4 OUT4 IN5 OUT5 IN6 EN VCC TOL REFERENCE OUT6 VCC UNDERVOLTAGE LOCKOUT MAX16061C VCC MARGIN Figure 2. MAX16061C Functional Diagram 12 ______________________________________________________________________________________ 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors WDI MR SRT VCC VCC WATCHDOG TIMER CIRCUIT TIMING RESET CIRCUIT RESET IN1 OUT1 IN2 OUT2 IN3 OUT3 OUTPUT DRIVER IN4 OUT4 IN5 OUT5 IN6 OUT6 IN7 OUT7 IN8 EN VCC TOL REFERENCE OUT8 VCC UNDERVOLTAGE LOCKOUT MAX16062C VCC MARGIN Figure 3. MAX16062C Functional Diagram ______________________________________________________________________________________ 13 MAX16060/MAX16061/MAX16062 Functional Diagrams (continued) MAX16060/MAX16061/MAX16062 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors Detailed Description The MAX16060/MAX16061/MAX16062 are 1% accurate low-voltage, quad-/hex-/octal-voltage µP supervisors in a small thin QFN package. These devices provide supervisory functions for complex multivoltage systems. The MAX16060 monitors four voltages; the MAX16061 monitors six voltages; and the MAX16062 monitors eight voltages. These supervisors offer independent outputs for each monitored voltage along with a reset output that asserts whenever any of the monitored voltages fall below their respective thresholds or the manual reset input is asserted. The reset output remains asserted for the reset timeout after all voltages are above their respective thresholds and the manual reset input is deasserted. The minimum reset timeout is internally set to 140ms or can be adjusted with an external capacitor. All open-drain outputs have internal 30µA pullups that eliminate the need for external pullup resistors. However, each output can be driven with an external voltage up to 5.5V. Other features offered include a manual reset input, a tolerance pin for selecting 5% or 10% input thresholds, and a margin enable function for deasserting the outputs during margin testing. Window Detection A window detector circuit uses two inputs in the configuration shown in Figure 6. External resistors set the two threshold voltages of the window detector circuit. External logic gates create the OUT signal. The window detection width is the difference between the threshold voltages (Figure 7). 5V VCC V1 IN1 V2 IN2 V3 IN3 V4 IN4 MAX16060 OUT1 OUT2 OUT3 OUT4 GND Figure 4. Quad Undervoltage Detector with LED Indicators An additional feature is a watchdog timer that asserts RESET when the watchdog timeout period (1.6s typ) is exceeded. The watchdog timer can be disabled by leaving WDI unconnected. 5V D1 Applications Information Undervoltage-Detection Circuit The open-drain outputs of the MAX16060/ MAX16061/MAX16062 can be configured to detect an undervoltage condition. Figure 4 shows a configuration where an LED turns on when the comparator output is low, indicating an undervoltage condition. These devices can also be used in applications such as system supervisory monitoring, multivoltage level detection, and VCC bar-graph monitoring (Figure 5). VIN (5V) VCC OUT1 OUT2 IN2 IN3 D3 MAX16060 OUT3 D4 Tolerance (TOL) The MAX16060/MAX16061/MAX16062 feature a pinselectable threshold tolerance. Connect TOL to GND to select 5% threshold tolerance. Connect TOL to VCC to select 10% threshold tolerance. IN4 OUT4 GND Figure 5. VCC Bar-Graph Monitoring 14 D2 IN1 ______________________________________________________________________________________ 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors ) (VTH + VTH_HYS) R1 R2 VINTH 5V R1 VCC R1 R2 INPUT IN1 OUT1 IN2 MAX16060E OUT2 IN3 R2 OUT OUT3 VTH R3 IN4 OUT4 R4 (VV R1 = R2 INTH TH ) -1 GND Figure 8. Setting the Adjustable Input ( ) Adjustable Input R3 VTH4 = 1 + R4 VTH These devices offer several monitor options with adjustable input thresholds (see Table 1). The threshold voltage at each adjustable IN_ input is typically 0.394V (TOL = GND) or 0.373V (TOL = VCC). To monitor a voltage VINTH, connect a resistive-divider network to the circuit as shown in Figure 8. VINTH = VTH ((R1/R2) + 1) R1 = R2 ((VINTH/VTH) - 1) Figure 6. Window Detection OUT1 V TH1 Large resistors can be used to minimize current through the external resistors. For greater accuracy, use lowervalue resistors. Unused Inputs OUT4 V TH4 Connect any unused IN_ inputs to a voltage above its threshold. OUT_ Outputs OUT ΔV TH Figure 7. Output Response of Window Detector Circuit The OUT_ outputs go low when their respective IN_ inputs drop below their specified thresholds. The output is open drain with a 30µA internal pullup to VCC. For many applications, no external pullup resistor is required to interface with other logic devices. An external pullup resistor to any voltage from 0 to 5.5V overrides the internal pullup if interfacing to different logic supply voltages. Internal circuitry prevents reverse current flow from the external pullup voltage to VCC (Figure 9). ______________________________________________________________________________________ 15 MAX16060/MAX16061/MAX16062 ( VTH1 = 1 + MAX16060/MAX16061/MAX16062 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors VCC = 3.3V 5V IN_ VTH_ VTH_ 100kΩ VCC VCC RESET OUT_ 90% RESET 10% tRD tRP OUT_ MAX16060 MAX16061 MAX16062 90% 10% GND GND tD Figure 9. Interfacing to a Different Logic Supply Voltage tD Figure 10. Output Timing Diagram RESET Output Manual Reset Input (MR) RESET asserts low when any of the monitored voltages fall below their respective thresholds or MR is asserted. RESET remains asserted for the reset timeout period after all monitored voltages exceed their respective thresholds and MR is deasserted (see Figure 10). This open-drain output has a 30µA internal pullup. An external pullup resistor to any voltage from 0 to 5.5V overrides the internal pullup if interfacing to different logic supply voltages. Internal circuitry prevents reverse current flow from the external pullup voltage to VCC (Figure 9). Many µP-based products require manual reset capability, allowing the operator, a test technician, or external logic circuitry to initiate a reset. A logic-low on MR asserts RESET low. RESET remains asserted while MR is low, and during the reset timeout period (140ms min) after MR returns high. The MR input has an internal 20kΩ pullup resistor to VCC, so it can be left unconnected if not used. MR can be driven with TTL or CMOS-logic levels, or with open-drain/collector outputs. Connect a normally open momentary switch from MR to GND to create a manual reset function. External debounce circuitry is not required. If MR is driven from long cables or if the device is used in a noisy environment, connecting a 0.1µF capacitor from MR to GND provides additional noise immunity. Reset Timeout Capacitor The reset timeout period can be adjusted to accommodate a variety of µP applications. Adjust the reset timeout period (t RP ) by connecting a capacitor (C SRT ) between SRT and GND. Calculate the reset timeout capacitor as follows: t (s) x ISRT CSRT (F) = RP VTH _ SRT Connect SRT to VCC for a factory-programmed reset timeout of 140ms (min). 16 ______________________________________________________________________________________ 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors Undervoltage Lockout (UVLO) The MAX16060/MAX16061/MAX16062 feature a VCC undervoltage lockout (UVLO) that preserves a reset status even if VCC falls as low as 1V. The undervoltage lockout circuitry monitors the voltage at VCC. If VCC falls below the UVLO falling threshold (typically 1.735V), RESET is asserted and all OUT_ are asserted low. This eliminates an incorrect RESET or OUT_ output state as VCC drops below the normal VCC operational voltage range of 1.98V to 5.5V. During power-up as V CC rises above 1V, RESET is asserted and all OUT_ are asserted low until V CC exceeds the UVLO threshold. As VCC exceeds the UVLO threshold, all inputs are monitored and the correct output state appears at all the outputs. This also ensures that RESET and all OUT_ are in the correct state once VCC reaches the normal VCC operational range. Power-Supply Bypassing In noisy applications, bypass VCC to ground with a 0.1µF capacitor as close to the device as possible. The additional capacitor improves transient immunity. For fast-rising VCC transients, additional capacitance may be required. ______________________________________________________________________________________ 17 MAX16060/MAX16061/MAX16062 Margin Output Disable (MARGIN) MARGIN allows system-level testing while power supplies are adjusted from their nominal voltages. Drive MARGIN low to force RESET and OUT_ high, regardless of the voltage at any monitored input. The state of each output does not change while MARGIN = GND. The watchdog timer continues to run when MARGIN is low, and if a timeout occurs, RESET will assert tMD after MARGIN is deasserted. The MARGIN input is internally pulled up to VCC. Leave MARGIN unconnected or connect to VCC if unused. RESET 13 8 MR IN1 14 7 OUT4 6 OUT3 15 14 13 12 11 RESET 16 10 MR IN1 17 9 OUT6 8 OUT5 7 OUT4 6 VCC IN2 18 MAX16060 IN2 15 SRT 9 MARGIN 10 OUT3 SRT 11 OUT2 MARGIN 12 TOP VIEW OUT1 OUT2 TOP VIEW OUT1 Pin Configurations MAX16061 IN3 19 1 THIN QFN (4mm x 4mm) 2 3 4 5 GND 4 WDI 3 IN6 2 IN4 + GND TOL 20 WDI 1 VCC IN5 5 + IN4 TOL 16 IN3 OUT4 MARGIN SRT 18 OUT3 TOP VIEW OUT2 OUT1 THIN QFN (4mm x 4mm) 17 16 15 14 13 RESET 19 12 MR IN1 20 11 OUT8 IN2 21 10 OUT7 9 OUT6 8 OUT5 7 VCC MAX16062 IN3 22 IN4 23 + IN7 4 5 6 GND 3 WDI 2 IN8 1 IN6 TOL 24 IN5 MAX16060/MAX16061/MAX16062 1% Accurate, Quad-/Hex-/Octal-Voltage µP Supervisors THIN QFN (4mm x 4mm) Chip Information PROCESS: BiCMOS Package Information For the latest package outline information, go to www.maxim-ic.com/packages. PACKAGE TYPE PACKAGE CODE DOCUMENT NO. 16 TQFN T1644-4 21-0139 20 TQFN T2044-3 21-0139 24 TQFN T2444-4 21-0139 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 18 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2008 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.