openGear® OPG-1L 50 MHz – 2.3 GHz RF Fiber Optic Link DATASHEET | OCTOBER 2013 SATCOM EMCORE’s openGear® OPG-1L RF Fiber Optic Links are optimized to perform in the 50 MHz to 2.3 GHz frequency range providing transparent signal transport for satellite antenna applications on an open architecture platform. The OPG-1L transmitter and receiver modules may be housed in the same chassis as EMCORE’S openGear® HD video, audio, serial data and USB extension / distribution cards, allowing full monitoring and control of each module via the DashBoard Network Management System (NMS). System Design Features The OPG-1L was designed to be fully compatible 50 MHz to 2.3 GHz Optimized for IF- and L-Band Video Signals Supports 30 km Links** Optically-Isolated DFB Lasers Enable HighDynamic-Range Links 25 dB Tx and Rx Adjustable Gain Range with the openGear® standard for terminal equipment or cable headend design. This means that when you install an openGear® enclosure, you can then purchase additional insert cards from different manufacturers to be used in the same enclosure. The standard enclosure is a 19” rack-mount frame that can hold up to 20 insert cards. A separate module handles the management and control systems, and allows for local or remote interfaces. Each enclosure utilizes 2 RU of rack space, maximizing the overall usage Peak Optimizer for Quick and Easy Set-Up of the equipment rack. SmartGain for Enhanced AGC Performance The OPG-1L’s Rear Interface Modules may be pre-installed with its cabling, with- 50 & 75 Ohm BNC or 50 Ohm SMA Blind Mate RF Coax to Support Rear Plug-in Access out corresponding PCBA cards. This allows the user to anticipate future expansion needs without significantly increasing the intial investment, and without having to access the rear panel and cabling once installed. The user simply purchases corresponding PCBA cards on an as-needed basis then slides them into place from the SC/APC and LC/APC Optical Connectors Tx & Rx RF Power Monitors Via LED, SMA, Dashboard and SNMP front of the frame, effortlessly locking them into the Rear Interface Module. Block Diagram Dashboard and SNMP Monitoring and Control Transmitter Tx and Rx PCBA Card and Module 2 RU, 20-Slot openGear® Enclosure Receiver DC to LNB LNB Power Capable Sin Push Button Laser PL PR Photodiode Sout Smon Optimizer Smon CE & CSA Certified, RoHS **For higher optics, please contact us © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. openGear® OPG-1L 50 MHz – 2.3 GHz RF Fiber Optic Link DATASHEET | OCTOBER 2013 SATCOM Performance Highlights Frame Options Parameter TX Value Wavelength 1310, 1550 nm 5+2 dBmo 50-1000 850-2300 MHz MHz Optical Output Power IF-Band Frequency L-Band Frequency Units OPG-8321 Frequency Response Any 500 MHz Full Band (50-2300 MHz) + 0.75 + 1.5 dB dB 10 dB 25 + 2 dB 30 dB Spurs Free Dynamic Range 98 dB-Hz2/3 Noise Figure (at maximum gain, 25°C) 23 dB Input Return Loss (minimum) 1 Total Front-End RF Gain (at minimum attenuation setting) Attenuation Adjustment Range 2 Input IP3 (at maximum gain, 25°C) -4 dBm 2 + 2dB dBm 10 dB 20 (dual output) 25 (single output) dB Total RF Power Into Laser RX Output Return Loss (Minimum) 1 Total Front-End RF Gain (at minimum attentuation setting) Attenuation Adjustment Range Output IP3 (at maximum gain, 25°C) 15 dB 20 (dual output) 25 (single output) dBm 1. Link RF Gain dB = TG + RG - 2*Fiber Loss dBo 2. SFDR = 2/3*(IIP3 + 174 - NF). OG3-FR OPG-1L PCBA Cards with Rear Interface Modules Mechanical Characteristics Parameter PCBA Card Dimension Rear Interface Module Dimension Value1 Units 12.8 L x 3.0 H x 0.681 W 32.5 L x 7.62 H x 0.173W in cm 1.362 L x 3.365 H x 1.31 W 3.46 L x 8.55 H x 3.33 W in cm PCBA Cards 1. Defined per openGear Development Guide by Ross: 8200DR-001-02, 8200DR-001-03 Electrical Characteristics Parameter TX Value Power Requirement W 12 +/- 0.5 VDC LNB Voltage (at RF input port, 350 mA max) 17 +/- 1.0 VDC DC Current (@ +12 V with LNB Off) 350 +/- 50 mA Input Voltage (@ 1 A Max) 12 +/- 0.5 VDC DC Current (@ +12 V) 250 +/- 50 mA Input Voltage (@ 1 A Max) RX Units 12 © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 Rear Interface Modules [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. openGear® OPG-1L 50 MHz – 2.3 GHz RF Fiber Optic Link DATASHEET | OCTOBER 2013 SATCOM Card Compatibility to openGear® Frames © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. openGear® OPG-1L 50 MHz – 2.3 GHz RF Fiber Optic Link DATASHEET | OCTOBER 2013 SATCOM Ordering Information PCBA Card Receiver Transmitter1 OPG-UT-YY05-ZZ OPG-UR-V-ZZ Note 1. When installing transmitter cards in the OG3-FR frame, remove the pre-installed LNB blocker plug from the PCBA card but leave as-is for the OPG-8321 frame to prevent the frame’s DC-power alarm from activating. When ordering replace “U” with one of the Frequency Band Options When ordering replace “V” with one of the RX Only: RF Interface Options When ordering replace “YY” with one of the Wavelength Options** When ordering replace “ZZ” with one of the Optical Connector Options Frequency Band Options “U” Frequency Band (MHz) RX Only: RF Interface Options “V” Wavelength Options (nm) “YY” Output Power (dBmo) Optical Connector Options “ZZ” I = IF-Band 50-1000 1 = Output+Monitor 2 = Dual Outputs 13 = 1310, 55 = 1550 05 = +5 LA = LC-APC, SA = SC-APC (OG3-FR only) L = L-Band 850-2300 1 = Output+Monitor 2 = Dual Outputs 13 = 1310, 55 = 1550 05 = +5 LA = LC-APC, SA = SC-APC (OG3-FR only) Ordering Information for Rear Interface Module (RIM) Transmitter/Receiver OPG-WX RF Connector Options “W” B = BNC, S = SMA RF Connector Impedance Options (ohm) “X” 5 = 50, 7 = 75 (BNC only) When ordering replace “W” with one of the RF Connector Options When ordering replace “X” with one of the RF Connector Impedance Options Laser Safety This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser product. This device has been classified with the FDA/CDRH under accession number 0220191. All versions of this laser are Class 1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser products. For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warning shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and binoculars) may pose an eye hazard. Wavelength = 1.3/1.5 μm. Maximum power = 30 mW. *Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. *IEC is a registered trademark of the International Electrotechnical Commision. © 2013 EMCORE Corporation | REV 2013.10 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.