Hirose FH36W-51S-03SHW 0.3 mm pitch, 1.0 mm above the board flexible printed circuit zif connector Datasheet

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
NEW
0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
FH36 Series
1.0mm MAX
●Space saving (51 positions shown)
2.7mm
[51 Positions]
16.9mm
■Features
Metal fittings do not protrude outside of the connector body
1. Low-profile and light weight
Weight: Reduced approximately 30%
Board footprint: Reduced approximately 15%
(As compared with Hirose Electric's FH26 Series connectors
(51 positions)
●Can be mounted over conductive traces
2. Easy solderability on the PC board
The soldering leads are on 0.6 mm pitch, exiting on front and
back of the connector.
3. Conducive traces on the PCB can run under
the connector
No exposed contacts on the bottom of the connector.
4. Easy FPC insertion and reliable electrical
connection
Proven Flip Lock actuator allows easy insertion of FPC and
provides a tactile sensation when fully closed, confirming
complete electrical and mechanical connection.
5. FPC position hold
Tabs on each side of the FPC assure correct placement
and hold in the connector prior to closing of the actuator.
6. Accepts standard FPC thickness
No exposed contacts on the bottom of
the connector
●Operation
(1) Actuator open
(2) Insert FPC
1
Actuator
2
FPC
(3) Close the actuator
(4) FPC connected
0.2mm thick standard Flexible Printed Circuit (FPC) can be
used. This is the only ultra-low profile ZIF connector using
standard FPC.
7. Board placement with automatic equipment
3
4
Flat upper surface and tape and reel packaging facilitate
vacuum pick-up and placement.
Standard reel packaging contains 5,000 connectors.
8. Halogen-free *
(FH36W Series)
●FPC temporary hold
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
2010.9
1
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Specifications
Operating
Current rating 0.2 A DC (Note 1)
-55 to +85°C (Note 2)
temperature range
Operating
Relative humidity 90%
Voltage rating 30 Vrms AC
humidity range
max. (No condensation)
Rating
Recommended FPC
Thickness: 0.2±0.03mm Gold plated
Item
Specification
1.Insulation resistance 50 Mø min
2.Withstanding voltage No flashover or insulation breakdown
100 mø max.
3.Contact resistance
* Including FPC conductor resistance
Contact resistance: 100 mø max.
4.Durability
No damage, cracks, or parts dislocation
No electrical discontinuity of 1 µs or longer
5.Vibration
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
No electrical discontinuity of 1 µs or longer
6.Shock
Contact resistance: 100 mø max.
No damage, cracks, or parts dislocation
Contact resistance: 100 mø max.
7.Humidity
Insulation resistance: 50 Mø min.
(Steady state)
No damage, cracks, or parts dislocation
Contact resistance: 100 mø max.
8.Temperature cycle
Insulation resistance: 50 Mø min.
No damage, cracks, or parts dislocation
9.Resistance to
soldering heat
Storage
-10 to +50°C (Note 3)
temperature range
Storage
Relative humidity 90%
humidity range
max. (No condensation)
Conditions
100 V DC
90 Vrms AC / one minute
1 mA
10 cycles
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm
10 cycles in each of the 3 directions
Acceleration of 981m/s2, 6 ms duration,
sine half-wave, 3 cycles in each of the 3 axis
96 hours at a temperature of 40°C and humidity of
90 to 95%
Temperature:-55ç➝+15ç to +35ç➝+85ç➝+15ç to +35ç
Time: 30➝ 2 to 3 ➝ 30➝ 2 to 3 minutes
5 cycles
No deformation of components affection performance.
1) Reflow: At the recommended temperature profile.
2) Manual soldering: 350ç ± 10ç for 5 seconds
Note 1: When passing the current through all of the contacts, use 70% of the rated current.
Note 2: Includes temperature rise caused by current flow.
Note 3: The term "storage" refers to products stored for a long period prior to mounting and use.
The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage,
shipment or during transportation.
Note 4: Small blisters of the molding compounds in small areas will not affect form, fit or function.
Note 5: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and
specifications for a specific part number shown.
■Materials
Part
Material
Insulator
LCP
Actuator
Finish
Color: Beige
FH36 series: Dark brown
PA
Contacts
Phosphor bronze
Metal fittings
Remarks
UL94V-0
FH36W series: Light brown
UL94HB
Gold plating
-----------------
Pure tin reflow plating
-----------------
■Ordering information
FH 36 W - 51S - 0.3 SHW (50)
1
2
3
5
6
7
1 Series name
: FH
4 Number of positions : 11 to 61
2 Series No.
: 36
5 Contact pitch : 0.3mm
3 Blank :Standard
W :Halogen-free
(Flame retardance UL94HB).
2
4
6 Termination type: SMT horizontal staggered mounting type
7 Plating specifications (50)…Gold plating with nickel barrier
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Connector Dimensions
A±0.15
B±0.1
0.3±0.1
0.6±0.1
(0.12)
(2.75)
(1)
Lot No. indicator
A**
Cav No.
Number of contacts indicator
HRS mark
0.6±0.1
(0.12)
(1.0 MAX)
C±0.1
(0.47)
(D: FPC insertion slot dimension)
E±0.1
1
(0.25)
1
0.1
0.1
(2.7)
Note 1 : The coplanarity of each terminal lead is within 0.1.
Note 2 : Packaged on tape and reel only. Check packaging specification.
Note 3 : Slight discoloration in color of the plastic compounds does not affect form, fit or function of the connector.
Note 4 : After reflow, the terminal plating may change color, however this does not represent a quality issue.
All dimensions: mm
Part Number
FH36-15S-0.3SHW(50)
FH36-17S-0.3SHW(50)
FH36-19S-0.3SHW(50)
FH36-25S-0.3SHW(50)
FH36-29S-0.3SHW(50)
FH36-33S-0.3SHW(50)
FH36-35S-0.3SHW(50)
FH36-45S-0.3SHW(50)
FH36-51S-0.3SHW(50)
FH36-61S-0.3SHW(50)
FH36W-11S-0.3SHW(50)
FH36W-15S-0.3SHW(50)
FH36W-17S-0.3SHW(50)
FH36W-19S-0.3SHW(50)
FH36W-23S-0.3SHW(50)
FH36W-27S-0.3SHW(50)
FH36W-31S-0.3SHW(50)
FH36W-33S-0.3SHW(50)
FH36W-39S-0.3SHW(50)
FH36W-51S-0.3SHW(50)
FH36W-61S-0.3SHW(50)
CL No.
580-1618-8-50
580-1606-9-50
580-1607-1-50
580-1619-0-50
580-1613-4-50
580-1615-0-50
580-1604-3-50
580-1617-5-50
580-1601-5-50
580-1600-2-50
580-1625-3-50
580-1623-8-50
580-1616-2-50
580-1612-1-50
580-1614-7-50
580-1608-4-50
580-1609-7-50
580-1622-5-50
580-1620-0-50
580-1605-6-50
580-1611-9-50
Number of contacts
15
17
19
25
29
33
35
45
51
61
11
15
17
19
23
27
31
33
39
51
61
A
6.1
6.7
7.3
9.1
10.3
11.5
12.1
15.1
16.9
19.9
4.9
6.1
6.7
7.3
8.5
9.7
10.9
11.5
13.3
16.9
19.9
B
3.6
4.2
4.8
6.6
7.8
9
9.6
12.6
14.4
17.4
2.4
3.6
4.2
4.8
6
7.2
8.4
9
10.8
14.4
17.4
C
4.2
4.8
5.4
7.2
8.4
9.6
10.2
13.2
15
18
3
4.2
4.8
5.4
6.6
7.8
9
9.6
11.4
15
18
D
4.83
5.43
6.03
7.83
9.03
10.23
10.83
13.83
15.63
18.63
3.63
4.83
5.43
6.03
7.23
8.43
9.63
10.23
12.03
15.63
18.63
E
5.59
6.19
6.79
8.59
9.79
10.99
11.59
14.59
16.39
19.39
4.39
5.59
6.19
6.79
7.99
9.19
10.39
10.99
12.79
16.39
19.39
Tape and reel packaging (5,000 pieces/reel).
Order by number of reels.
3
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
(Recommended metal mask thickness: t=0.1)
B±0.05
0.6±0.05
0.3±0.03
(0.23:Metal mask)
(0.3:Metal mask)
0.4±0.05
0.535±0.05
C±0.05
■Recommended FPC Dimensions
0.3±0.07
R
2.2±0.3
S
0.2±0.03
0.3
0.9±0.2
B±0.03
J±0.05
B
A
Detail S
MAX R0.2
2.4±0.1
1.65±0.05
1.15±0.05
0.1±0.02
(0.2)
3.3±0.3 (Stiffener)
0.3 +0.04
– 0.03
+0.04
– 0.03
0.9±0.2
0±0.03
*RELATIVE POSITIONS OF
POINT A and B
(Lead plated 0.1 MAX)
(0.07)
0.1±0.15
0.75±0.1
0.85±0.1
1.45±0.1
0.6±0.02
0.3±0.02
disengagement shift
Detail R
F±0.1
G±0.1
H±0.05
C±0.03
0.3±0.07
(0.7:Metal mask)
0.95±0.05
0.03±0.05
0.3±0.05
(0.5)
0.8±0.05
(0.65:Metal mask)
0.3±0.05
(0.2)
(0.3)
0.6±0.05
0.3±0.03
(0.23:Metal mask)
1.67±0.05
(3.07)
0.6±0.05
(0.5:Metal mask)
■Recommended PCB mounting pattern and metal mask dimensions
R0.2±0.05
R0.2±0.1
(0.15)
R0.2±0.05
(R0.2)
(R0.2)
R0.2±0.05
All dimensions: mm
Part Number
FH36-15S-0.3SHW(50)
FH36-17S-0.3SHW(50)
FH36-19S-0.3SHW(50)
FH36-25S-0.3SHW(50)
FH36-29S-0.3SHW(50)
FH36-33S-0.3SHW(50)
FH36-35S-0.3SHW(50)
FH36-45S-0.3SHW(50)
FH36-51S-0.3SHW(50)
FH36-61S-0.3SHW(50)
FH36W-11S-0.3SHW(50)
FH36W-15S-0.3SHW(50)
FH36W-17S-0.3SHW(50)
FH36W-19S-0.3SHW(50)
FH36W-23S-0.3SHW(50)
FH36W-27S-0.3SHW(50)
FH36W-31S-0.3SHW(50)
FH36W-33S-0.3SHW(50)
FH36W-39S-0.3SHW(50)
FH36W-51S-0.3SHW(50)
FH36W-61S-0.3SHW(50)
4
CL No.
580-1618-8-50
580-1606-9-50
580-1607-1-50
580-1619-0-50
580-1613-4-50
580-1615-0-50
580-1604-3-50
580-1617-5-50
580-1601-5-50
580-1600-2-50
580-1625-3-50
580-1623-8-50
580-1616-2-50
580-1612-1-50
580-1614-7-50
580-1608-4-50
580-1609-7-50
580-1622-5-50
580-1620-0-50
580-1605-6-50
580-1611-9-50
Number of contacts
15
17
19
25
29
33
35
45
51
61
11
15
17
19
23
27
31
33
39
51
61
B
3.6
4.2
4.8
6.6
7.8
9
9.6
12.6
14.4
17.4
2.4
3.6
4.2
4.8
6
7.2
8.4
9
10.8
14.4
17.4
C
4.2
4.8
5.4
7.2
8.4
9.6
10.2
13.2
15
18
3
4.2
4.8
5.4
6.6
7.8
9
9.6
11.4
15
18
F
6.04
6.64
7.24
9.04
10.24
11.44
12.04
15.04
16.84
19.84
4.84
6.04
6.64
7.24
8.44
9.64
10.84
11.44
13.24
16.84
19.84
G
5.6
6.2
6.8
8.6
9.8
11
11.6
14.6
16.4
19.4
4.4
5.6
6.2
6.8
8
9.2
10.4
11
12.8
16.4
19.4
H
4.8
5.4
6
7.8
9
10.2
10.8
13.8
15.6
18.6
3.6
4.8
5.4
6
7.2
8.4
9.6
10.2
12
15.6
18.6
J
4.6
5.2
5.8
7.6
8.8
10
10.6
13.6
15.4
18.4
3.4
4.6
5.2
5.8
7
8.2
9.4
10
11.8
15.4
18.4
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Recommended FPC construction
●Contact FPC manufacturer for specific details.
1. Using Single-sided FPC
Connecting side
Material Name
Covering film layer
Material
Polyamide
1 mil thick.
Cover adhesive
Material Thickness
(µm)
(25)
(25)
Surface treatment
0.2µm thick gold plated over 1 to 5µm
thick nickel underplating
Copper foil
Cu
Base adhesive
Thermosetting adhesive
25
Base film
Polyamide
25
1oz
1 mil thick
3
35
Reinforcement material adhesive Thermosetting adhesive
40
Stiffener
Polyamide 3 mil thick
75
Total
203
Back side
2. Using Double-sided FPC
Connecting side
Material Name
Covering layer film
Material
Polyamide
1 mil thick
(25)
(25)
Cover adhesive
Back side
Material Thickness
(µm)
Surface treatment
0.2µm thick gold plated over 1 to 5µm
thick nickel underplating
Through-hole copper
Cu
Copper foil
Cu
Base adhesive
Thermosetting adhesive
18
Base film
Polyamide
25
3
15
1/2oz
1 mil thick
18
Base adhesive
Thermosetting adhesive
Copper foil
Cu
Cover adhesive
Thermosetting adhesive
25
Covering film layer
Polyamide
25
1/2oz
1 mil thick
18
(18)
Reinforcement material adhesive Thermosetting adhesive
25
Stiffener
25
Polyamide
1 mil thick
Total
197
* To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is NOT RECOMMENDED.
3.Precautions
1. This specification is a recommendation for the construction of the FH36 Series FPC (t=0.2 ± 0.03)
2. For details about the construction, please contact the FPC manufacturers.
5
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Packaging Specification
1.75±0.1
K±0.3
(N)
M±0.1
8±0.1
L±0.1
4±0.1 2±0.15
.5
(1.5)
(0.3)
Ø1
Ø1
(N)
M±0.1
(1.5)
(0.3)
.1
+0 0
.5
1.75±0.1
8±0.1
K±0.3
4±0.1 2±0.15
●Embossed Carrier Tape Dimensions
Flat surface, for placement
(Tape width of 32mm min.)
with automatic equipment.
+0
0 .1
●Embossed Carrier Tape Dimensions
(Tape width of 24mm max.)
(3.85)
(1)
Flat surface, for placement
with automatic equipment.
1.5 +0.1
0
Unreeling direction
(Ø1
3)
●Reel Dimensions
1.7 +0.15
0
(2.95)
(Ø80)
(Ø380)
(P:INSIDE)
(Q:OUTSIDE)
End section
No connector inserted
(25 pockets min.)
Part Number
FH36-15S-0.3SHW(50)
FH36-17S-0.3SHW(50)
FH36-19S-0.3SHW(50)
FH36-25S-0.3SHW(50)
FH36-29S-0.3SHW(50)
FH36-33S-0.3SHW(50)
FH36-35S-0.3SHW(50)
FH36-45S-0.3SHW(50)
FH36-51S-0.3SHW(50)
FH36-61S-0.3SHW(50)
FH36W-11S-0.3SHW(50)
FH36W-15S-0.3SHW(50)
FH36W-17S-0.3SHW(50)
FH36W-19S-0.3SHW(50)
FH36W-23S-0.3SHW(50)
FH36W-27S-0.3SHW(50)
FH36W-31S-0.3SHW(50)
FH36W-33S-0.3SHW(50)
FH36W-39S-0.3SHW(50)
FH36W-51S-0.3SHW(50)
FH36W-61S-0.3SHW(50)
6
Mounting section
Embossed carrier tape
CL No.
580-1618-8-50
580-1606-9-50
580-1607-1-50
580-1619-0-50
580-1613-4-50
580-1615-0-50
580-1604-3-50
580-1617-5-50
580-1601-5-50
580-1600-2-50
580-1625-3-50
580-1623-8-50
580-1616-2-50
580-1612-1-50
580-1614-7-50
580-1608-4-50
580-1609-7-50
580-1622-5-50
580-1620-0-50
580-1605-6-50
580-1611-9-50
Lead section (400mm min.)
No connector inserted
(25 pockets min.)
Number of contacts
15
17
19
25
29
33
35
45
51
61
11
15
17
19
23
27
31
33
39
51
61
K
16
16
16
24
24
24
24
24
32
32
16
16
16
16
24
24
24
24
24
32
32
Top cover tape
All dimensions: mm
L
Å|
Å|
Å|
Å|
Å|
Å|
Å|
Å|
28.4
28.4
Å|
Å|
Å|
Å|
Å|
Å|
Å|
Å|
Å|
28.4
28.4
M
7.5
7.5
7.5
11.5
11.5
11.5
11.5
11.5
14.2
14.2
7.5
7.5
7.5
7.5
11.5
11.5
11.5
11.5
11.5
14.2
14.2
N
6.3
6.9
7.5
9.3
10.5
11.7
12.3
15.3
17.1
20.1
5.1
6.3
6.9
7.5
8.7
9.9
11.1
11.7
13.5
17.1
20.1
P
17.4
17.4
17.4
25.4
25.4
25.4
25.4
25.4
33.4
33.4
17.4
17.4
17.4
17.4
25.4
25.4
25.4
25.4
25.4
33.4
33.4
Q
21.4
21.4
21.4
29.4
29.4
29.4
29.4
29.4
37.4
37.4
21.4
21.4
21.4
21.4
29.4
29.4
29.4
29.4
29.4
37.4
37.4
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Temperature Profile
●Using Lead-free Solder Paste
MAX 250ç
250
230ç
Temperature
(ç)
200
200ç
150
150ç
HRS test condition
Solder method
:Reflow, IR/hot air
Environment
:Room air
Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu
(Senju Metal Industry, Co., Ltd.'s
Part Number:M705-221CM5-32-10.5)
Test board
:Glass epoxy 25mm∞50mm∞0.8mm thick
Land dimensions :0.3mm∞0.6mm, 0.3mm∞0.8mm
Metal mask
:0.23∞0.5, 0.23∞0.65∞0.1mm thick
100
50
25ç (60sec.) 90 sec. to 120 sec.
Preheating
0
Start
(60sec.)
Soldering
The temperature profiles shown are based on the above
conditions.
In individual applications the actual temperature may vary,
depending on solder paste type, volume / thickness and board
size / thickness. Consult your solder paste and equipment
manufacturer for specific recommendations.
Time (Seconds)
7
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
■Operation and Precautions
Operation
1. FPC insertion procedure. Connector installed on the board.
1 Lift up the actuator.
Use thumb or index finger.
2 Insert the FPC (contact surfaces facing down) at angle of
approximately 10° to the board surface ①, making sure that
the FPC positioning tabs clear the protrusions on both sides
of the connector. Lower the FPC down ②, parallel to the
board surface.
FPC contact surface
faces downward
①
10°
②
Protrusions for
the FPC positioning.
3 Rotate down the actuator until firmly closed.
2. FPC removal
1 Lift up the actuator
Pull up the FPC at an angle of approximately 10° ① and than withdrew it from the connector ②.
125
°
②
10°
①
Protrusions for FPC positioning
8
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Precautions
Exercise care when handling connectors. Follow recommendations given below.
[ Precautions when mounting connectors on the PCB ]
◆Handling before mounting on PCB
Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED.
◆PC board warpage
Minimize the warpage as much as possible. The connector is straight within 0.1 mm max. Make sure that the mounting area flatness can accept the connector terminals without causing any failure of the solder joints.
◆When braking the large PC board into individual boards exercise care NOT to damage the installed connectors.
◆When attaching the boards or other components with the screws make sure that any stresses will NOT cause
board deflections affecting the mounting areas of the connector.
0.5MAX
Connector
0.6
100
Connector
F
Board
F
Board
Fig. 1
100
0.6
0.5MAX
◆Bending of the board
For a board width of 100 mm, bending of the board must be 0.5 mm max. (Ref to Fig. 1)
[ Precautions during FPC insertion and mating ]
Pay attention to the following points when inserting FPC.
◆Actuator operation
1 Do not apply excessive force when opening the actuator prior to FPC insertion. When opening make sure that
the force is applied only to the actuator itself, avoiding touching of the contacts.
Actuator
Damage to the actuator
Damage to the actuator
2 Axis of rotation
Assure free rotation of the actuator.
9
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Precautions
3 The actuator will rotate 125ç. Do not apply force to rotate further.
12
5°
4 When opening or closing the actuator, do so at the cen-
ter section.
5 Do not grasp or and lift the actuator (Fig. 3) nor insert the nail
from the back of it (Fig. 4).
Fig. 3
◆FPC insertion
Do not insert the FPC at any high angle from above.
10°
Protrusions for FPC positioning
10
Fig. 4
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Precautions
As illustrated (Fig. 5) angle insertion may cause electrical discontinuity when the FPC is deflected in use.
Opening of the FPC pattern
Fig. 5
• To avert insertion of the FPC at an angle, consideration should be given to securing enough insertion space
when designing the board lay-out. Insertion will be difficult when the FPC is too short.
• Contact FPC manufacturer for information about the bending specifications.
◆Verification of the fully closed actuator
The FPC should be fully inserted, with its positioning tabs fully behind the protrusions on both sides of the connector’s insertion slot (Fig. 6).
FPC positioning tab
Protrusions FPC positioning
Fig. 6
[ Routing of the FPC (FPC fully inserted / actuator closed) ]
◆Do not apply any pull or upward-directed force to the FPC.
Do not make any sharp bends of FPC close to the immediate exit from the connector (Fig. 7)
Fig. 7
11
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
FH36 Series●0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Precautions
[ Removing of the FPC ]
◆Rotate the actuator to the fully open position (max. angle of 125ç)
Lift the FPC approximately 10ç (making sure that the positioning tabs clear the protrusions on both sides) and
carefully withdraw it from the connector.
125
°
10°
Protrusions for FPC positioning
[ Other Precautions ]
◆Hand Soldering Precautions
When hand soldering:
1 Do not perform reflow or hand soldering with the FPC inserted in the connector.
2 Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads.
3 Do not use excessive amount of solder or flux compounds.
Operation of the actuator or contacts may be affected by excessive amounts of solder or flux compounds.
®
12
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN
PHONE: 81-3-3491-5300, FAX: 81-3-3495-5230
http://www.hirose.com
http://www.hirose-connectors.com
The contents of this catalog are current as of date of 09/2010. Contents are subject to change without notice for the purpose of improvements.
Similar pages