Renesas ISL58792 Laser diode driver with serial control and write current dac Datasheet

DATASHEET
ISL58792
Laser Diode Driver with Serial Control and Write Current DAC
FN7580
Rev 3.00
December 14, 2015
The ISL58792 is a highly integrated, single supply laser diode
driver designed to support multi-standard writable optical
drives in CD, DVD, and Blu-Ray formats at various speeds. It is
a ‘hybrid’ part having an interface compatible with a
conventional LDD, but an internal architecture similar to a
write strategy LDD. This combination adds versatility to the
conventional interface.
Features
The rise time, fall time and overshoot of all outputs are
adjustable to compensate for high and low resistance lasers.
• WEN Line Skew Detection
The ISL58792 architecture includes dual write current banks,
which can be selected using the bank select line, BSEL. This
eliminates the need to synchronize the serial port to the
media.
• 10-bit x 10-bit Multiplying DAC Output Provides 10-bit Full
Scale Adjustment and 10-bit Resolution at any Full Scale
Output
The oscillator is internally activated through program
assignment to attach to any WEN state.
The WEN lines have internal 100 terminators. There is a
skew detector on the WEN receiver outputs.
• Compatible with all Conventional Controllers Having a Serial
Port, with Some Programming
• Programmable Snubber on all Outputs
• Compatible with Future Controllers Having Gray Coded WEN
Lines for Glitchless High-Speed Operation
• 1000mA Maximum Total Write Output Current.
• Three Laser Outputs Allow Read/Write DVD, CD, and Blue
Combinations
• Single +5V Supply
• Analog Inputs Supports Read APC
Applications
• HFM Oscillator Programmable to 100mAP-P and Range
from 100MHz to >1GHz
• Combination DVD, CD, and Blue Writable Drives
• Programmable HFM On, Off and Cooling Levels
• BD Camcorders
• Programmable Spread Spectrum for Low EMI
• BD Video Recorders
• Built-in ADC to Sample Laser Voltage Allows Power
Reduction by Optimizing Headroom
• Built-in Thermal Sensor Aids in Thermal Design
• Serial Input Works up to 50MHz
• Pb-Free (RoHS Compliant)
FN7580 Rev 3.00
December 14, 2015
Page 1 of 16
ISL58792
Application Block Diagram
2.2µF
0.1µF
2.2µF
BEAD
0.1µF
VHI= +5V TO +9V
4.7µF
0.1µF
+5V
SCLK
SDIO
GND
SEN
IBLUE
BEAD
WEB
4.7µF
SERIAL
INTERFACE
MAIN BOARD CONTROLLER
TR TF OVERSHOOT
ADJUST
VSO
WEN0
WEN0B
WDAC2
AMPLITUDE
REGISTERS
(8EA)
WEN1
WEN1B
WEN2
WRITE
REGISTER
SELECTOR
WDAC1
BLUE
WDAC
SKEW
DETECT
GND
SCALE DAC
WEN2B
IOUT1
VSO
AMPLITUDE
OSC
AND
BUFFER
SS
BSEL
0.1µF
FREQ
X
IOUT2
GAIN
CONTROL
RFREQ
READ
DAC
READ
+
MAIN BOARD
AFE
+
IAPC
VSO
REFERENCE
BIAS AND
POWER
INTERNAL 2.5V
REGULATOR
VSL
GND
ENA
0.1µF
RSET
1µF
FN7580 Rev 3.00
December 14, 2015
Page 2 of 16
ISL58792
Ordering Information
PART NUMBER
(Note 2)
PART
MARKING
PACKAGE
Tape & Reel
(Pb-free)
TEMP RANGE
(°C)
PKG.
DWG.#
ISL58792CRTZ
587 92CRTZ
-10 to +85
24 Ld TQFN
L24.4x4E
ISL58792CRTZ-T13 (Note 1)
587 92CRTZ
-10 to +85
24 Ld TQFN
L24.4x4E
ISL58792CRTZ-T7A (Note 1)
587 92CRTZ
-10 to +85
24 Ld TQFN
L24.4x4E
1. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil
Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
Pin Configuration
19 IBLUE
20 GND
21 SEN
22 SDIO
23 SCLK
24 WEB
ISL58792
(24 LD TQFN)
TOP VIEW
WEN0 1
18 VSO
WEN0B 2
17 IOUT1
WEN1 3
16 GND
THERMAL
PAD
WEN1B 4
15 IOUT2
RSET 12
GND 11
VSL 10
IAPC 9
13 ENA
RFREQ 8
14 VSO
WEN2B 6
BSEL 7
WEN2 5
Pin Descriptions
PIN
NAME
PIN
NUMBER
I/O
PIN
TYPE
WEN0,
WEN0B
1, 2
I
LVDS
Write Enable 0. When WEN0 > WEN0B, the result is a logic 1 in the write current selection. Otherwise it is
logic 0.
WEN1,
WEN1B
3, 4
I
LVDS
Write Enable 1. When WEN1 > WEN1B, the result is a logic 1 in the write current selection. Otherwise it is
logic 0.
WEN2,
WEN2B
5, 6
I
LVDS
Write Enable 2. When WEN2 > WEN2B, the result is a logic 1 in the write current selection. Otherwise it is
logic 0.
BSEL
7
I
Digital
Bank Select input selects the write current register banks.
RFREQ
8
I/O
Analog
A resistor from RFREQ to GND sets the range of the HFM frequency.
IAPC
9
I
Analog
A 1k impedance current input; 100*IAPC flows to the output. This controls the read current, which may
also include a current from an internal DAC.
VSL
10
O
Power
The internal 2.5V regulator; a 1µF capacitor from VSL to GND is recommended. Do not use VSL for other
loads.
GND
11, 16, 20
Ground
Ground
RSET
12
Analog
A resistor from RSET to analog ground sets the DAC full-scale current.
FN7580 Rev 3.00
December 14, 2015
I/O
PIN DESCRIPTION
Page 3 of 16
ISL58792
Pin Descriptions (Continued)
PIN
NAME
PIN
NUMBER
I/O
PIN
TYPE
ENA
13
I
Digital
Chip enable input (H = enable, L = disable)
VSO
14, 18
Power
Supply voltage. (connect all pins)
IOUT2
15
O
Analog
Laser diode output #2
IOUT1
17
O
Analog
Laser diode output #1
IBLUE
19
O
Analog
Blue laser diode output
SEN
21
I
Digital
Serial control enable (H = enable, L = disable)
SDIO
22
I/O
Digital
Serial data for parameters and control; in/out
SCLK
23
I
Digital
Serial control clock
WEB
24
I
Digital
Write enable Bar. When low, write current is enabled.
PD
Thermal
PIN DESCRIPTION
The Thermal pad should be grounded and connected to a heat sink.
NOTE: Pins with the same name are internally connected together; however, LDD pins must not be used for connecting together external components or
features.
FN7580 Rev 3.00
December 14, 2015
Page 4 of 16
ISL58792
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
VSO, Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V
IBLUE, Voltage at IBLUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7V
IOUT1,2, Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000mApk
IBLUE, Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600mApk
VIN, Logic Input Voltages . . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to VSO + 0.5V
IIN, Current into RSET, RFREQ, IAPC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
ESD Rating
Human Body Model (Tested per JESD22-A114F) . . . . . . . . . . . . . 1500V
Machine Model (Tested per JESDD22 A115B). . . . . . . . . . . . . . . . . 100V
Charge Device Model (Tested per JESDD22-C101D). . . . . . . . . . . 1500V
Latch-up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA @+125°C
Thermal Resistance (Typical)
JA (°C/W) JC (°C/W)
24 Lead TQFN (Notes 3, 4) . . . . . . . . . . . . .
42
5.4
PD, Maximum Power Dissipation . . . . . . . . . . . . see Figure 12 on page 13
TS, Storage Temperature Range. . . . . . . . . . . . . . . . . . . . .-60°C to +150°C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions
TA, Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . -10°C to +85°C
TJ, Junction Temperature Range. . . . . . . . . . . . . . . . . . . . -10°C to +150°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
3. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
4. For JC, the “case temp” location is the center of the exposed metal pad on the package underside.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise
noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Standard Conditions Unless otherwise indicated, all of the following tables are: VSO = VHI = 5V, RSET = 620Ω, RFREQ = 4.7kΩ,
RLOAD-IOUT1/2 = 8Ω to GND, RLOAD-BLUE = 10Ω to VHI, PMAX = 0x3FF, Reg 1-21 = 88h, Reg x-00 bit6 = 0, TA = +25°C.
Electrical Specifications
Standard conditions apply unless otherwise noted.
PARAMETER
DESCRIPTION
MIN
(Note 13)
TYP
MAX
(Note 13)
UNIT
5.7
V
7.0
V
DC ELECTRICAL SPECIFICATIONS
VSO
(Notes 5, 6)
4.5
VIBLUE
IBLUE pin; RLOAD = 10
IVSO
Supply Current (No Current Output)
19
30
mA
IS, dis(nom)
Supply Current, Disable Mode
17
100
µA
IS, dis(high)
Supply Current; VSO = 5.5V, Disable Mode
25
100
µA
IBLUE-LEAK1
VIBLUE = 7.0V; IBLUE is Selected; CE = OE = 1; Reg1-21 = 00h
150
300
µA
IBLUE-LEAK2
VIBLUE = 7.0V; IBLUE is Selected; CE = OE = 1; IAPC pin voltage = 0V
80
µA
IBLUE-LEAK3
VIBLUE = 7.0V; IBLUE is not Selected; CE = OE = 1
1.6
mA
VIH
Input Logic High Level
VIL
Input Logic Low Level
VOH
SDIO High Level, IL = -5mA
VOL
SDIO Low Level, IL = 5mA
IINH
Logic Input Current High Level
IINL
Logic Input Current Low Level
1.1
2.0
V
0.8
2.4
V
V
0.4
V
-15
+15
µA
-15
+10
µA
NOTES:
5. Required voltage at the device pins. Allowance must be made for any voltage drop between the power supply and the device.
6. Required voltage also depends on laser diode manufacturer and pickup optical efficiency. Also, see ROUT spec of WDAC.
FN7580 Rev 3.00
December 14, 2015
Page 5 of 16
ISL58792
PMAX DAC (10-bit) DC Specifications Standard conditions apply unless otherwise noted.
PARAMETER
DESCRIPTION
MIN
(Note 13)
CONDITIONS
DNL-PMAX
Differential Non-Linearity
(Note 7)
INL-PMAX
Integral Non-Linearity
At 200h Resistive Load ~0V to ~3V
ZS-PMAX
Zero-Scale Error
(Note 8)
VRSET
RSET Pin Voltage
TYP
-3.5
MAX
(Note 13)
UNIT
+3.5
LSB
+40
LSB
-2
0
+2
LSB
1.03
1.06
1.11
V
NOTES:
7. Differential non-linearity (DNL) is the differential between the measured and ideal 1 LSB change of any two adjacent codes.
8. Zero-scale error (ZS) is the deviation from zero current output when the digital input code is zero.
IOUT1/2 Write Power DAC (10-bit) DC Specifications Standard conditions apply unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 13)
TYP
-1.7
MAX
(Note 13)
UNIT
+1.0
LSB
DNL-W
Differential Non-Linearity
INL-W
Integral Non-Linearity
At 200h Resistive Load
~0V to ~3V
FSOUT-W620
Write DAC Full-Scale Output Current
RSET = 620
WriteDAC = 0x3FF. Headroom depends
on IOUT
FSOUT-H1.1
Write DAC Full-Scale Output Current
WriteDAC = 0x3FF,
Fixed Headroom = 1.1V
PSRR-FS
Power Supply Rejection - Full-Scale
Current
vs VSO (Note 9)
-30
dB
TC-FS-IOUT
Temperature Coefficient - Full-Scale Current
(Note 10) 0°C to +85°C
-32
ppm/C
ZS-W
Zero-scale Error
(Note 11)
ROUT-WDAC
Write DAC Output Series Resistance
WriteDAC = PMAX = 0x3FF
PMAX bias overdriven (Note 12)
+21
LSB
475
525
mA
700
800
-2
875
mA
0
+2
LSB
1.1
1.4

NOTES:
9. Full scale output current power supply sensitivity (SFS) is measured by varying the VSO from 4.5V to 5.5V DC and measuring the effect of this signal
on the full-scale output current.
10. Full scale output current temperature coefficient (TFS) is given by delta (full scale output current)/(T).
11. Zero-scale error (ZS) is the deviation from zero current output when the digital input code is zero.
12. PMAX bias overdriven via RSET.
13. Compliance to datasheet limits is assured by one or more methods: production test, characterization and/or design.
FN7580 Rev 3.00
December 14, 2015
Page 6 of 16
ISL58792
IBLUE Write Power DAC (10-bit) DC Specifications Standard conditions apply unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITIONS
DNL-W
Differential Non-Linearity
INL-W
Integral Non-Linearity
At fixed 2.5V headroom
FSOUT-H2.0
Write DAC Full-Scale Output Current
RSET = 620
WriteDAC = 0x3FF; Fixed Headroom = 2.0V;
Reg 1-21 = 8F
TRRANGE
Tr Tf Adjustment Range
Reg 1-0A from X0h to X7h
PSRR-FS
Power Supply Rejection - Full-Scale Current
vs VSO (Note 14)
TCFS-IBLUE
Temperature Coefficient - Full-Scale Current (Note 15)
ZS-W
Zero-Scale Error
VIOUT = 2V (Note 16)
ROUT-WDAC
Write DAC Output Series Resistance
WriteDAC = PMAX = 0x3FF
PMAX bias overdriven (Note 17)
MIN
(Note 13)
TYP
-4.9
MAX
(Note 13)
UNIT
+2.0
LSB
+60
380
-8
450
LSB
575
mA
1
ns
-40
dB
600
ppm/C
0
+8
LSB
3.4
4.5

NOTES:
14. Full scale output current power supply sensitivity (SFS) is measured by varying the VSO from 4.5V to 5.5V DC and measuring the effect of this signal
on the full-scale output current.
15. Full scale output current temperature coefficient (TFS) is given by delta (full scale output current)/(T).
16. Zero-scale error (ZS) is the deviation from zero current output when the digital input code is zero.
17. PMAX bias overdriven via RSET.
IBLUE Read APC Amplifier DC Specifications Standard conditions apply unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 13)
TYP
MAX
(Note 13)
UNIT
IAPCMIN-GAIN
Current Gain @ Min Gain
Reg1-21h = 1X, IAPC = 0µA, 500µA
8
15
25
mA/mA
IAPCMAX-GAIN
Current Gain @ Max Gain
Reg1-21h = FX, IAPC = 0µA, 500µA
195
250
295
mA/mA
IAPCGAIN
Current Gain
IAPC = 0µA, 500µA
95
135
175
mA/mA
IAPCOS
Current Offset
IAPC = 0µA
-2
1
3
mA
LINAPC
Output Current Linearity; Best Fit
IAPC = 0µA, 500µA, 1.0mA
-12
1
%
IOUT-R-APC
Blue Read Output Current, Using IAPC Input
IAPC = 1.5mA
150
RIN
IAPC Input Impedance to GND
PSRRAPC
IAPC Current Power Supply Rejection
700
IOUT-average = 100mA, varying VSO
mA
950
1200
-46

dB
OUT1/2 Read APC Amplifier DC Specifications Standard conditions apply unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 13)
TYP
MAX
(Note 13)
UNIT
IAPCMIN-GAIN
Current Gain @ Min Gain
Reg1-21h = 1X, IAPC = 0µA, 500µA
11
14.5
19
mA/mA
IAPCMAX-GAIN
Current Gain @ Max Gain
Reg1-21h = FX, IAPC = 0µA, 500µA
155
173
200
mA/mA
IAPCGAIN
Current Gain
IAPC = 0µA, 500µA
85
100
115
mA/mA
IAPCOS
Current Offset
IAPC = 0µA
-2
1
3
mA
LINAPC
Output Current Linearity; Best Fit
IAPC = 0µA, 500µA, 1.0mA
-1
6
%
IOUT-R-APC
Read Output Current, Using IAPC Input
IAPC = 1.5mA
RIN
IAPC Input Impedance to GND
PSRRAPC
IAPC Current Power Supply Rejection
FN7580 Rev 3.00
December 14, 2015
120
700
IAPC-IN = 0.45mA, varying VSO
mA
950
-48
1200

dB
Page 7 of 16
ISL58792
Read DAC (12-bit) DC Specifications Standard conditions apply unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 13)
TYP
MAX
(Note 13)
UNIT
+2
LSB
DNL-R
Read DAC Differential Non-Linearity
PREAD: Reg 0-19 + Reg 1-09
-2
INL-R
Read DAC Integral Non-Linearity
@ 900h on Resistive Load.
0V to ~3V
IOUT-R-DAC-RED
Read Output Current, Read DAC at
Full-Scale, IOUT1 or IOUT2
PREAD = 0xFFF, IAPC = 0mA,
Reg 1-21 = 8F
PSRR-FS
Power Supply Rejection - Full-Scale
Current
Varying the VSO (Note 18)
-42
dB
TC-FS-IOUT
Temperature Coefficient - Full-Scale
Current
Not including the RSET tempco
(Note 19) 0°C to +85°C
-48
ppm/C
ZS-R
Zero-Scale Error
VIOUT = 2V (Note 20)
+90
120
LSB
150
-80
180
0
80
mA
LSB
NOTES:
18. Full scale output current power supply sensitivity (SFS) is measured by varying the VSO from 4.5V to 5.5V DC and measuring the effect of this signal
on the full-scale output current.
19. Full scale output current temperature coefficient (TFS) is given by delta (full scale output current)/(T).
20. Zero-scale error (ZS) is the deviation from zero current output when the digital input code is zero.
HFM (High Frequency Modulator)
PARAMETER
Standard conditions unless otherwise noted.
DESCRIPTION
CONDITIONS
MIN
(Note 13)
TYP
MAX
(Note 13)
UNIT
IMAX-RED-OFF-LINK
Max HFM Off DC Output, IOUT1 or IOUT2 in
Link Mode
HFMOFF = 0xFFF
110
145
180
mA
IMAX-RED-OFF-UNLINK
Max HFM Off DC Output, IOUT1 or IOUT2 in
Unlink Mode
HFMOFF = 0xFFF
100
135
170
mA
IMAX-BLUE-OFF
Max HFM Off DC Output, IBLUE
HFMOFF = 0xFFF
45
62
75
mA
IMIN-RED-OFF
Min HFM Off DC Output, IOUT1 or IOUT2
HFMOFF = 0x000
-3
0
3
mA
IMIN-BLUE-OFF
Min HFM Off DC Output, IBLUE
HFMOFF = 0x000
-3
0
3
mA
IMAX-RED-ON-LINK
Max HFM Oscillator Output, IOUT1 or IOUT2
in Link Mode
HFMON = Reg 0-17h = 0xFF
118
mAP-P
IMAX-RED-ON-UNLINK
Max HFM Oscillator Output, IOUT1 or IOUT2
in Unlink Mode
HFMON = Reg 0-17h = 0xFF
114
mAP-P
IMAX-BLUE-ON
Max HFM Oscillator Output, IBLUE
HFMON = 0xFF
60
mAP-P
FOSC-HI-MAX
Max HFM Frequency, High Range
Reg 0-16 = FFh, Reg X-00 bit 6 = 0
900
1086
1300
MHz
FOSC-HI-MIN
Min HFM Frequency, High Range
Reg 0-16 = 01h, Reg X-00 bit 6 = 0
135
190
255
MHz
FOSC-LO-MAX
Max HFM Frequency, Low Range
Reg 0-16 = FFh, Reg X-00 bit 6 =1
470
565
670
MHz
FOSC-LO-MIN
Min HFM Frequency, Low Range
Reg 0-16 = 01h, Reg X-00 bit 6 = 1
55
80
110
MHz
PSRROSC-FREQ
PSRR - HFM Frequency
VSO from 4.5V to 5.0V
PSRROSC-AMP-IOUT
PSRR - HFM Amplitude
PSRROSC-AMP-IBLUE
0.5
%/V
350MHz; HFMON = FFh; Link
3
%/V
PSRR - HFM Amplitude
700MHz; HFMON = FFh; Link
1.2
%/V
TFOSC400MAX
HFM Frequency Temperature Coefficient
Range from 200MHz to 400MHz
0 - 900
ppm/C
TFOSC900MAX
HFM Frequency Temperature Coefficient
Range from 400MHz to 900MHz
±250
ppm/C
VRFREQ
RFREQ Pin Voltage
RFREQ = 4.7k
0.9
1.03
1.2
V
SS-WIDTH-10h
Spread Spectrum Spreading Width
RFREQ = 4.7kReg 1-18 = 10h,
Reg 0-16 = 26h; Reg X-00 bit 6 = 0
0.15
0.35
0.75
%
SS-WIDTH-70h
Spread Spectrum Spreading Width
RFREQ = 4.7kReg 1-18 = 70h,
Reg 0-16 = 26h; Reg X-00 bit 6 = 0
0.65
1.4
2.1
%
FN7580 Rev 3.00
December 14, 2015
Page 8 of 16
ISL58792
HFM (High Frequency Modulator)
PARAMETER
Standard conditions unless otherwise noted. (Continued)
DESCRIPTION
CONDITIONS
MIN
(Note 13)
TYP
MAX
(Note 13)
UNIT
1.7
2.8
4
%
SS-WIDTH-78h
Spread Spectrum Spreading Width
RFREQ = 4.7kReg 1-18 = 78h,
Reg 0-16 = 26h; Reg X-00 bit 6 = 0
SS_Shift
Shift of Center Frequency when SS is
Enabled vs when it’s Disabled
RFREQ = 4.7kReg 1-18 = 00h to
40h, Reg 0-16 = 26h; Reg X-00
bit 6 = 0
SS_Mod
Spread Spectrum Modulation Frequency
REG 1-18h Bit 7 = 0; Reg X-00
bit 6 = 0
50
76
105
kHz
SS_Mod
Spread Spectrum Modulation Frequency
REG 1-18h Bit 7 = 1; Reg X-00
bit 6 = 0
25
44
65
kHz
MAX
(Note 13)
UNIT
50
MHz
1.4
%
Serial Interface AC Performance Standard conditions unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 13)
TYP
FSER
SCLK Operating Range
Static logic not limited at low frequency
tEH
SEN “H” Time
@ 50MHz
320
ns
tEL
SEN “L” Time
@ 50MHz
160
ns
tERSR
SEN Rising Edge to the First SCLK Rising Edge
@ 50MHz
10
ns
tCDS
SDIO Set Up Time
@ 50MHz
10
ns
tCDH
SDIO Hold Time
@ 50MHz
10
ns
tSREF
Last SCLK Rising Edge to SEN Falling Edge
@ 50MHz
10
ns
tCC
SCLK Cycle Time1
@ 50MHz
20
ns
Duty
SCLK “H” Duty Cycle
@ 50MHz
40
tCDD
SDIO Output Delay
@ 50MHz
tEDH
SDIO Output Hold Time
@ 50MHz
50
60
%
4
ns
2
ns
LVDS Specifications Standard conditions unless otherwise noted.
PARAMETER
DESCRIPTION
CONDITIONS
MIN
(Note 13)
TYP
MAX
(Note 13)
UNIT
VIN-HIGH
Maximum Single Line Voltage
2.4
V
VIN-LOW
Minimum Single Line Voltage
0
V
RIN
Input Resistance
VMIN
Minimum Differential Voltage
FN7580 Rev 3.00
December 14, 2015
85
Signal tested with ±240mV differential input
240
100
115

mVPK
Page 9 of 16
ISL58792
Laser Driver AC Performance Demo board test, 10% duty cycle pulse, load = equivalent circuitry to [laser + flex cable] and/or as noted.
VSO = 5V. TA = +25°C
PARAMETER
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
tR-IOUTx
IOUT1/2 Write Rise Time (10% to 90%)
300mW Optical ML229U7
1.3
ns
tF-IOUTx
IOUT1/2 Write Fall Time (10% to 90%)
300mW Optical ML229U7
800
ps
O/S-IOUTx
IOUT1/2 Write Pulse Overshoot
300mW Optical ML229U7
11
%
tD-IOUTx
IOUT1/2 Write Pulse Delay From LVDS = Zero
crossing to IOUT rise 10%
5.3
ns
tR-BLUE
IBLUE Write Rise Time (10% to 90%)
300mW Optical
650
ps
tF-BLUE
IBLUE Write Fall Time (10% to 90%)
300mW Optical
450
ps
O/S-BLUE
IBLUE Write Pulse Overshoot
300mW Rising Optical
12
%
tD-BLUE
IBLUE Write Pulse Delay From LVDS = Zero
crossing to IOUT rise 10%
5.2
ns
INOISE-IOUTx
IOUT1/2 Read Output Current Noise
IOUT = 50mA, measured @ 10MHz
0.55
nA/Hz
INOISE-IOUTx
IOUT1/2 Read and HFM Output Current Noise
IOUT = 50mA+30mAP-P; measured @ 10MHz
0.96
nA/Hz
INOISE-BLUE
IBLUE Read Output Current Noise
IOUT = 50mA, measured @ 10MHz
0.37
nA/Hz
INOISE-BLUE
IBLUE Read and HFM Output Current Noise
IOUT = 50mA+10mAP-P; measured @ 10MHz
0.47
nA/Hz
BWAPC
Read Amplifier 3dB Bandwidth
IOUT = 50mA
0.5
MHz
TABLE 1. AMPLITUDE SELECTION REGISTER ACTIVATION
NAME
ENA
WEB
CR0
Bit 2
WEN2
WEN1
WEN0
MSB
BSEL = 0
LSB
BSEL = 0
MSB
BSEL = 1
LSB
BSEL = 1
OFF
0
X
x
X
X
X
X
X
X
X
READ
1
1
0
X
X
X
0-19
1-09
0-19
1-09
W0
1
0
1
0
0
0
0-10
2-10
0-11
2-11
W1
1
0
1
0
0
1
0-04
2-04
0-05
2-05
W2
1
0
1
0
1
0
0-06
2-06
0-07
2-07
W3
1
0
1
0
1
1
0-08
2-08
0-09
2-09
W4
1
0
1
1
0
0
0-0A
2-0A
0-0B
2-0B
W5
1
0
1
1
0
1
0-0C
2-0C
0-0D
2-0D
W6
1
0
1
1
1
0
0-0E
2-0E
0-0F
2-0F
W7
1
0
1
1
1
1
0-12
2-12
0-13
2-13
NOTES:
21. There are two sets of write current registers. When BSEL = 1, bank 1 is selected. When BSEL = 0, bank 0 is selected.
22. Read and write are independent. Read is enabled with a control bit.
23. Register terminology is page Number-Register number (hex). Thus 1-09 is page 1, register 09h.
FN7580 Rev 3.00
December 14, 2015
Page 10 of 16
ISL58792
Applications Information
FOSC
IOUT
Both FOSC and RFREQ may be chosen to accommodate the
desired range or operating point of the HFMFREQ DAC. Although
FOSC is relatively linear with DAC code, monotonicity is not
guaranteed (see Figures 5 and 6).
The data sheet values for oscillator current, and write current are
based on an RSET of 620 when PMAX and WriteDAC are both set to
full scale. The user may choose RSET to match the output current
needs of the application.
The PMAX DAC is biased by IRSET (= VRSET/RSET). See the
“Typical Performance Curves” on page 11.
The write channel output capability for a typical part is shown in
Figures 1, 2, and 3. The amount of IOUT will be limited by the
available headroom voltage at the IOUTx pins.
A four input DAC (Reg 1-0A bits 3, 2, 1, 0) can be used to control
the amount of RC snubbing applied to the outputs. For IBLUE,
there is an extra bit (Reg 1-0A bit 4) weighted as MSB.
Read current may be controlled by either the Read DAC or the
IAPC input. When set by the PREAD DAC, IREAD is limited to the
data sheet value, whereas the IAPC input will allow a significantly
higher value to be obtained. The ReadDAC and IAPC currents sum
together.
Glitches could occur if two or three WEN lines are changed
simultaneously, and the propagation delay is different for the two
lines between the inner circuits of the controller and the inner
circuits of the LDD. Because the WEN lines are encoded, the
selected write current will be correct before the change in code,
and again after the code changes. But some other output could
result momentarily if the propagation delays are not matched.
The skew detector detects the first rising edge at the LVDS
outputs.
The oscillator may be turned on by the WEN code selected. The
particular code that selects the oscillator is under program
control. The PCOOL function is also available through the program
control and WEN selection.
The WEB enables write current. WEN code 000 through 111 will
select a write current as described in Table 1.
Power
The main power consumption is caused by the headroom voltage
across the output stage (VSO - VIOUT) x IOUT. For IOUT1 and IOUT2,
the VSO can be reduced below 5.0V, as long as sufficient
headroom voltage is available to obtain the desired output
current. For the blue outputs, the built in ADC can be used to
obtain the output voltage, which is also the headroom voltage.
The HFM oscillator power consumption will increase with
increasing frequency and amplitude (see Figure 7).
Note that in the TQFN package, the die is mounted directly on the
thermal pad. This provides a very low thermal resistance Junction
to thermal pad of just a few °C/W. The problem is in moving the
heat from the thermal pad to some other heat sink.
Figure 12 shows that when mounted well on a 4-layer PCB with 3
ground plane layers, and an area of 10cmx10cm, the JA is
+42°C/W. The typical application will not afford this good of a
heat sink.
Typical Performance Curves
IOUT2 (mA)
1000
800
500
IOUT2 vs VHEAD vs PMAX CODE
3FFh
(REG 1-21 = 88h) (VSO = 4.5V)
(RSET = 620)
300h
200h
600
100h
400
80h
200
0
0.5
1.0
1.5 2.0 2.5 3.0
VHEADROOM (V)
3.5
4.0
FIGURE 1. IOUT WRITE CURRENT vs VHEADROOM vs PMAX
FN7580 Rev 3.00
December 14, 2015
300h
300
200h
200
100h
100
40h
0.0
3FFh
400
IBLUE (mA)
1200
4.5
0
40h
001h
0
1
2
3
4
5
VHEADROOM (V)
6
7
FIGURE 2. IBLUE vs PMAX vs VHEADROOM (VSO = 5.0V)
(RSET = 620) (1-21 = FFh), (RLOAD = 10)
Page 11 of 16
8
ISL58792
Typical Performance Curves
250
IBLUE (mA)
250
IBLUE vs VHEAD vs PMAX CODE
(Reg 1-21 = 88h) (VSO = 4.5V)
(RSET = 620)
3FFh
200
300h
150
200h
100
200
IBLUE (mA)
300
(Continued)
100h
50
80h
0
40h
0
1
2
3
4
VHEADROOM (V)
5
0.836mA
0mA
0
0
6
1
RFREQ = 3900
3
4
VHEADROOM (V)
FOSC (MHz)
TEMP = +125°C
800
600
7
HFMFREQUENCY, INT RFREQ, MHz (COUNTER)
0
32
64
96
128
160
192
224
800
RFREQ = 4700
600
400
VSO = 5.0V
CR0 - Bit6 = 0
400
200
0
256
0
32
64
96
90
3.0
192
224
256
80h TO F0h
2.5
HFMON = 80
00h TO 78h
2.0
SS SHIFT (%)
HFMON = FF
70
160
FIGURE 6. HFM CONTROL; VSO = 5.0V
FIGURE 5. HFM CONTROL vs TEMPERATURES
80
128
HFM DAC (dec)
HFM DAC (dec)
ISO CONSUMPTION (mA)
6
1000
1000
60
50
1.5
1.0
0.5
80h TO F8h ATE
0.0
-0.5
40
30
5
CR0 - bit6 = 0
1200
TEMP = +25°C
1200
2
0.441mA
FIGURE 4. IBLUE READ vs VHEADROOM vs IAPC,
(REG 1-21 = 88h) (VSO = 5.0V), (RSET = 620)
1400
1400
FOSC (MHz)
1.228mA
100
50
FIGURE 3. IBLUE WRITE CURRENT vs VHEADROOM vs PMAX
200
1.622mA
150
HFMON = 01
0
100
200 300
400
500 600
700
800
900
HFM FREQ (Hz)
FIGURE 7. HFM OSCILLATOR CURRENT CONSUMPTION
FN7580 Rev 3.00
December 14, 2015
-1.0
HFMON = 40
1G
-1.5
HFMFreq = 400MHz
0
1
2
3
4
5
6 7 8 9 10 11 12 13 14 15 16
SS SETTING (DEC)
FIGURE 8. IBLUE SS SHIFT vs SS SETTING @ 400MHz
Page 12 of 16
ISL58792
Typical Performance Curves
(Continued)
10
NOISE (nARMS/(Hz)
NOISE (nARMS/(Hz)
10.0
50mA + 10mAP-P
1.0
50mA
0.1
50mA + 30mAP-P
1.0
0.1
1M
10M
50mA
0.1
100M
0.1
1M
FREQUENCY (Hz)
10M
100M
FREQUENCY (Hz)
FIGURE 9. IBLUE NOISE vs FREQUENCY
FIGURE 10. IOUTx NOISE vs FREQUENCY
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD - QFN EXPOSED
DIEPAD SOLDERED TO PCB PER JESD51-5
700
3.5
POWER DISSIPATION (W)
BANDWIDTH (kHz)
600
500
400
300
200
0.0
0.6
1.2
1.8
IAPC (mA)
2.4
FIGURE 11. IOUT/IAPC BANDWIDTH vs IAPC
FN7580 Rev 3.00
December 14, 2015
3.0
2.98W
3.0

2.5
JA =
2.0
1.5
TQ
+4
FN
24
2°
C/
W
1.0
0.5
0
0
25
125
50
75 85 100
AMBIENT TEMPERATURE (°C)
150
FIGURE 12. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
Page 13 of 16
ISL58792
PIN #1 IDENTIFICATION
CHAMFER 0.350 X 45°
2.600±0.050
EXP.DAP
0.400±0.050
0.500 BSC
2.600±0.050
EXP.DAP
0.250±0.050
BOTTOM VIEW
0.150
EXPOSED TIE BAR
0.203 REF.
0.262
0.000-0.050
0.100
0.213
0.625
SIDE VIEW
FIGURE 13. TIE BAR LOCATION FOR 4X4 TQFN
FN7580 Rev 3.00
December 14, 2015
Page 14 of 16
ISL58792
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to web to make
sure you have the latest Rev.
DATE
REVISION
CHANGE
December 14, 2015
FN7580.3
Removed ISL58792CRTZ-EVAL from Ordering Information table.
Updated POD L24.4x4E from rev 0 to rev 2. Changes since rev 2:
- Bottom View - Changed Exposed paddle dimension from 2.50 to 2.60
- Made correction in Typical land pattern - added 0 to .250
- Added tolerance to Exposed DAP in Bottom view:
From: 2.60 sq.
To: 2.60 ±0.10 with added square graphic in front of the 2.60
July 29, 2013
FN7580.2
Updated Products information verbiage to About Intersil verbiage.
January 6, 2012
FN7580.1
Added ISL58792CRTZ and ISL58792CRTZ-T7A to “Ordering Information” on page 3.
November 29, 2010
FN7580.0
Initial release.
About Intersil
Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products
address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets.
For the most updated datasheet, application notes, related documentation and related parts, please see the respective product
information page found at www.intersil.com.
You may report errors or suggestions for improving this datasheet by visiting www.intersil.com/ask.
Reliability reports are also available from our website at www.intersil.com/support.
© Copyright Intersil Americas LLC 2010-2015. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7580 Rev 3.00
December 14, 2015
Page 15 of 16
ISL58792
Package Outline Drawing
L24.4x4E
24 LEAD THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE
Rev 2, 2/14
4.00
6
PIN #1 INDEX
AREA
20X 0.50
A
B
24
19
6
PIN 1
INDEX AREA
18
1
4.00
Exp. DAP
2.60 ±0.10
(4X)
6
13
0.15
0.10 M C A B
24X 0.250 ±0.050 4
7
12
SIDE VIEW
TOP VIEW
24X 0.400 ±0.050
BOTTOM VIEW
SEE DETAIL "X"
( 3.80 )
( 2.60)
0.10 C
Max 0.80
SEATING PLANE
0.08 C
SIDE VIEW
( 20X 0.50)
( 3.80 )
( 2.60 )
C
(24X 0.250)
0 . 2 REF
5
0 . 00 MIN.
0 . 05 MAX.
( 24 X 0.60)
DETAIL "X"
TYPICAL RECOMMENDED LAND PATTERN
NOTES:
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Dimension b applies to the metallized terminal and is measured
between 0.15mm and 0.30mm from the terminal tip.
5.
Tiebar shown (if present) is a non-functional feature.
6.
The configuration of the pin #1 identifier is optional, but must be
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
FN7580 Rev 3.00
December 14, 2015
Page 16 of 16
C