SURFACE MOUNT SUPER FAST RECTIFIER ES1A THRU ES1J VOLTAGE RANGE 50 to 600 Volts CURRENT 1.0 Ampere FEATURES • • • • • DO-214AC(SMA) Plastic package has underwrites laboratory flammability Classification 94V-0 Glass passivated chip junction Built-in strain relief Super Fast switiching speed for high efficiency High temperature soldering guaranteed 250℃/10 seconds MECHANICAL DATA • • • • Case: Transfer molded plastic Terminals: Solder plated, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Weight: 0.002ounce, 0.064 gram Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20%. SYMBOLS ES1A ES1B Maximum Repetitive Peak Reverse Voltage VRRM 50 100 Maximum RMS Voltage VRMS 35 70 Maximum DC Blocking Voltage VDC 50 100 Maximum Average Forward Rectified Current At TA=55℃(NOTE 1) Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Maximum Instantaneous Forward Voltage at 1.0A TA = 25℃ Maximum DC Reverse Current at rated DC blocking voltage at TA = 125℃ ES1G 400 280 400 ES1J 600 420 600 UNIT Volts Volts Volts Amps IFSM 30 Amps VF 0.95 1.25 5.0 100 IR Typical Junction Capacitance (Measured at 1.0MHz and applied reverse voltage of 4.0V) CJ Storage Temperature Range ES1E 300 210 300 1.0 trr Operating Junction Temperature ES1D 200 140 200 I(AV) Maximuml Reverse Recovery Time Test conditions IF =0.5A, IR =1.0A, IRR =0.25A Typical Thermal Resistance (NOTE 1) ES1C 150 105 150 RθJA RθJL TJ TSTG 10 nS 8 88 28 (-55 to +150) (-55 to +150) Web Site: www.cnmic.com Volts µA 35 Notes: 1. Thermal resistance from Junction to ambient and from junction to lead mounted on PCB. with 0.2×0.2″(5.0 × 5.0mm) copper pad areas. E-mail: [email protected] 1.7 pF ℃/W ℃ ℃ SURFACE MOUNT SUPER FAST RECTIFIER ES1A THRU ES1J VOLTAGE RANGE 50 to 600Volts CURRENT 1.0 Ampere FIG.1-TYPICAL FORWARD CURRENT FIG.2-MAXIMUM NON-REPETITIVE PEAK DERATING CURVE FORWARD SURGE CURRENT PEAK FORWARD SURGE 1.2 0.8 0.6 0.4 Single Phase Half Wave 60Hz Resistive or Inductive Load 0.375″(9.5mm) Lead Length 0.2 30 CURRENT, (A) 1.0 (A) AVERAGE FORWARD CURRENT, RATING AND CHRACTERISTIC CURVES ES1A THRU ES1J 8.3ms Single Half Sine-W ave (JEDEC M ethod) Tj = Tjmax 20 10 1 Cycle 0 0 25 100 75 50 55 125 175 150 0 1 2 AMBIENT TEMPERATURE, (° C) 4 6 8 10 40 20 60 100 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS TJ = 25° C 1.0 Pulse Width=300us 1% Duty Cycle 0.1 100 10 (μA) INSTANTANEOUS REVERSE CURRENT, 10 (A) INSTANTANEOUS FORWARD CURRENT, 100 TJ =125° C 1.0 TJ =25℃ 0.1 0 20 40 60 80 100 120 140 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) INSTANTANEOUS FORWARD VOLTAGE,(V) FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE,(pF) 1000 ES1A-ES1D ES1F-ES1J F1G.6-TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC Trr 50Ω 10Ω NONINDUCTIVE NONINDUCTIVE +0.5A (-) 100 (+) 25 Vdc (approx.) (-) TJ =25° C f= 1MHz Vsig=50mVp-p 1.0 1Ω NON INDUCTIVE 0 -0.25A (+) OSCILLOSCOPE (NOTE 1) -1.0A 10 0.1 PULSE GENERATIOR (NOTE 2) D.U.T. 10 100 REVERSE VOLTAGE,(V) E-mail: [email protected] NOTES : 1.Rise Time=7ns max. Input Impedance= 1 magohm. 22pF 2.Rise time=10ns max. Source Impedance= 50 ohms Web Site: www.cnmic.com 1cm SET TIME BASE FOR 50/100ns/cm