DS1233 5V EconoReset www.dalsemi.com FEATURES PIN ASSIGNMENT Automatically restarts microprocessor after power failure Monitors pushbutton for external override Internal circuitry debounces pushbutton switch Maintains reset for 350 ms after VCC returns to an in-tolerance condition or pushbutton released Accurate 5%, 10% or 15% microprocessor 5V power supply monitoring Reduces need for discrete components Precision temperature-compensated voltage reference and voltage sensor Low-cost TO-92 package or surface-mount SOT-223 package Internal 5kΩ=pull-up resistor Operating temperature of -40°C to +85°C DALLAS DS1233 Econo Reset 1 1 2 3 1 2 3 TO-92 PACKAGE See Mech. Drawings Section 2 4 3 SOT-223 PACKAGE See Mech. Drawings Section PIN DESCRIPTION PIN 1 PIN 2 PIN 3 PIN 4 GROUND RESET VCC GROUND (SOT-223 ONLY) DESCRIPTION The DS1233 EconoReset monitors two vital conditions for a microprocessor: power supply and external override. A precision temperature compensated reference and comparator circuit are used to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition, the reset signal is kept in the active state for approximately 350 ms to allow the power supply and processor to stabilize. The second function of the DS1233 is pushbutton reset control. The DS1233 debounces a pushbutton closure and will generate a 350 ms reset pulse upon release. OPERATION - POWER MONITOR The DS1233 provides the functions of detecting out-of-tolerance power supply conditions and warning a processor-based system of impending power failure. When VCC is detected as out-of-tolerance, as defined by the tolerance of the part selected, the RST signal is asserted. On power-up, RST is kept active for approximately 350 ms after the power supply has reached the selected tolerance. This allows the power supply and microprocessor to stabilize before RST is released. 1 of 5 111899 DS1233 OPERATION - PUSHBUTTON RESET The DS1233 provides for a pushbutton switch to be connected to the RST output pin. When the DS1233 is not in a reset cycle, it continuously monitors the RST signal for a low going edge. If an edge is detected, the DS1233 will debounce the switch by pulling the RST line low. After the internal timer has expired, the DS1233 will continue to monitor the RST line. If the line is still low, the DS1233 will continue to monitor the line looking for a rising edge. Upon detecting a release, the DS1233 will force the RST line low and hold it low for 350 ms. NOTE: For proper operation with an external pushbutton, a capacitor between 100 pF and 0.01 µF must be connected between RST and ground. In applications where additional reset current is required, a minimum capacitance of 500 pF should be used, along with a parallel external pull-up resistor of 1 kΩ=minimum. BLOCK DIAGRAM Figure 1 APPLICATION EXAMPLE Figure 2 2 of 5 DS1233 PUSHBUTTON RESET Figure 3 POWER UP Figure 4 POWER DOWN Figure 5 3 of 5 DS1233 ABSOLUTE MAXIMUM RATINGS* Voltage on VCC Pin Relative to Ground Voltage on I/O Relative to Ground Operating Temperature Storage Temperature Soldering Temperature * -0.5V to +7.0V -0.5V to VCC +0.5V -40°C to +85°C -55°C to +125°C 260°C for 10 seconds This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS (-40°C to +85°C) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES Supply Voltage VCC 1.2 5.0 5.5 V 1 (-40°C to +85°C; VDD=5V ± 10%) DC ELECTRICAL CHARACTERISTICS PARAMETER SYMBOL VOL MIN Output Current @ 0.4V IOL +8 Operating Current ICC VCC Trip Point 5% VCCTP0 4.50 VCC Trip Point 10% VCCTP1 VCC Trip Point 15% VCCTP2 Output Capacitance COUT Pushbutton Detect PBDV Pushbutton Release PBRD Low Level @ RST Internal Pull-Up Resistor RP VCC Detect to RST SYMBOL tRST MAX 0.4 UNITS V mA µA 4.625 4.75 V 1 4.25 4.375 4.49 V 1 4.0 4.125 4.24 V 1 10 pF 3.3 V 1 0.3 0.8 V 1, 2 5 6.25 kΩ 1.8 3.75 (-40°C to +85°C; VCC=5V ± 10%) MIN 250 TYP 350 tRPD MAX 450 UNITS ms 100 ns VCC Slew Rate (4.75V - 4.00V) tF 300 µs VCC Slew Rate (4.00V - 4.75V) tR 0 ns Pushbutton Debounce PBDB 250 350 450 ms VCC Detect to RST tRPU 250 350 450 ms NOTES: 1. All voltages are referenced to ground. 2. With a 100 pF to 0.01 µF capacitor connected from RST to ground. 4 of 5 NOTES 1 50 AC ELECTRICAL CHARACTERISTICS PARAMETER RESET Active Time TYP NOTES DS1233 ECONORESET SELECTION GUIDE VCC TRIP POINT 5V 3.3V PUSHBUTTON DETECT MIN TYP MAX MIN TYP MAX DS1233-15 4.0 4.125 4.24 2.4 - 3.3 DS1233-10 4.25 4.375 4.49 2.4 - 3.3 DS1233-5 4.5 4.625 4.75 2.4 - 3.3 DS1233D-15 4.0 4.125 4.24 N/A N/A DS1233D-10 4.25 4.375 4.49 N/A N/A DS1233D-5 4.5 4.625 4.75 N/A N/A DS1833-15 4.0 4.125 4.24 N/A N/A DS1833-10 4.25 4.375 4.49 N/A N/A DS1833-5 4.5 4.625 4.75 N/A N/A DS1233A-15 2.64 2.72 2.80 1.8 - 3.0 DS1233A-10 2.8 2.88 2.97 1.8 - 3.0 5 of 5