Features • Fast Read Access Time - 120 ns • Word-wide or Byte-wide Configurable • Dual Voltage Range Operation • • – Unregulated Battery Power Supply Range, 2.7V to 3.6V or Standard 5V ± 10% Supply Range 4-Megabit Flash and Mask ROM Compatable Low Power CMOS Operation – 20 µA Maximum Standby – 10 mA Max. Active at 5 MHz for VCC = 3.6V JEDEC Standard Packages – 44-Lead PLCC – 44-Lead SOIC (SOP) – 48-Lead TSOP (12 mm x 20 mm) High Reliability CMOS Technology – 2,000 ESD Protection – 200 mA Latchup Immunity Rapid™ Programming Algorithm - 50 µs/word (typical) CMOS and TTL Compatible Inputs and Outputs – JEDEC Standard for LVTTL and LVBO Integrated Product Identification Code Commercial and Industrial Temperature Ranges The AT27BV400 is a high performance low-power, low-voltage 4,194,304-bit one time programmable read only memory (OTP EPROM) organized as either 256K by 16 or 512K by 8 bits. It requires only one supply in the range of 2.7 to 3.6V in normal read (continued) PLCC Pin Configurations AT27BV400 Preliminary Pin Name Function A0 - A17 Addresses O0 - O15 Outputs O15/A-1 Output/Address BYTE/VPP Byte Mode/ Program Supply CE Chip Enable OE Output Enable NC No Connect SOIC (SOP) NC NC A17 A7 A6 A5 A4 A3 A2 A1 A0 CE GND OE O0 O8 O1 O9 O2 O10 O3 O11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 NC NC A8 A9 A10 A11 A12 A13 A14 A15 A16 BYTE/VPP GND 015/A-1 O7 O14 O6 O13 O5 O12 O4 VCC A4 A3 A2 A1 A0 CE GND OE O0 O8 O1 6 5 4 3 2 1 44 43 42 41 40 • • 7 8 9 10 11 12 13 14 15 16 17 39 38 37 36 35 34 33 32 31 30 29 18 19 20 21 22 23 24 25 26 27 28 • • A12 A13 A14 A15 A16 BYTE/VPP GND O15/A-1 07 O14 O6 O9 O2 O10 O3 O11 NC VCC O4 O12 O5 O13 • A5 A6 A7 A17 NC GND NC A8 A9 A10 A11 Description 4-Megabit (256K x 16 or 512K x 8) Unregulated Battery-Voltage™ High Speed OTP EPROM • TSOP Type 1 A15 A14 A13 A12 A11 A10 A9 A8 NC NC NC NC NC NC NC NC A17 A7 A6 A5 A4 A3 A2 A1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 A16 BYTE/VPP GND 015/A-1 O7 O14 O6 O13 O5 O12 O4 VCC O11 O3 O10 O2 O9 O1 O8 O0 OE GND CE A0 AT27BV400 Preliminary Rev. 0989A–03/98 1 mode operation. The by-16 organization makes this part ideal for portable and hand held 16- and 32-bit microprocessor systems using either regulated or unregulated battery power. Atmel’s innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consumption of a 3V supply. At V CC = 2.7V, any word can be accessed in less than 120ns. With a typical power dissipation of only 10 mW at 5mHZ and VCC = 3V, the AT27BV400 consumes less than one fifth the power of a standard 5V EPROM. Standby mode supply current is typically less than 1 mA at 3V. The AT27BV400 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation. The AT27BV400 can be organized as either word-wide or byte-wide. The organization is selected via the BYTE/VPP pin. When BYTE/VPP is asserted high (VIH), the word-wide organization is selected and the O15/A-1 pin is used for O15 data output. When BYTE/VPP is asserted low (V IL),the byte wide organization is selected and the O15/A-1 pin is used for the address pin A-1. When the AT27BV400 is logically regarded as x16 (word-wide), but read in the bytewide mode, then with A-1= VIL the lower 8 bits of the 16-bit word are selected with A-1 = VIH the upper 8 bits of the 16bit word are selected. The AT27BV400 is available in industry standard JEDECapproved one-time programmable (OTP) PLCC, SOIC (SOP), and TSOP packages. The device features two-line control(CE,OE) to eliminate bus contention. With high density 256K word or 512K byte storage capability, the AT27BV400 allows firmware to be to be stored reliably and to be accessed by the system without the delays of mass storage media. The AT27BV400 operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic Block Diagram 2 AT27BV400 devices operating at VCC = 5V. At V CC = 2.7V, the part is compatible with JEDEC approved low voltage battery operation (LVBO) interface specifications. The device is also capable of standard 5-volt operation making it ideally suited for dual supply range systems or card products that are pluggable in both 3-volt and 5-volt hosts. Atmel’s AT27BV400 has additional features that ensure high quality and efficient production use. The RapidTM Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 50µs/word. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry standard programming equipment to select the proper programming equipment and voltages. The AT27BV400 programs exactly the same way as a standard 5V AT27C400 and uses the same programming equipment. System Considerations Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device non-conformance. At a minimum, a 0.1 µF high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the V CC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 µF bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array. AT27BV400 Absolute Maximum Ratings* Temperature Under Bias ................................ -55°C to +125°C *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note: Minimum voltage is -0.6V DC which undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is Vcc + 0.75V DC which may overshoot to + 7.0V for pulses of less than 20 ns. Storage Temperature ..................................... -65°C to +150°C Voltage on Any Pin with with Respect to Ground ..................................-2.0V to +7.0V(1) Voltage on A9 with Respect to Ground ......................................-2.0V to +14.0V(1) VPP Supply Voltage with Respect to Ground .......................................-2.0V to +14.0V(1) 1. Operating Modes Outputs Mode/Pin CE Read Word-wide VIL OE VIL BYTE/VPP O0-O7 O8-O14 O15/A-1 (1) VIH DOUT DOUT DOUT (1) Ai X Read Byte-wide Upper VIL VIL X VIL DOUT High Z VIH Read Byte-wide Lower VIL VIL X(1) VIL DOUT High Z VIL Output Disable X(1) VIH X(1) X VIH (1) X (1) VIL VIH Ai VPP DIN PGM Verify X VIL Ai VPP DOUT PGM Inhibit VIH VIH X(1) VPP High Z VIH Identification Code Standby Rapid Program (3) (6) X X High Z High Z (4) Product Identification(5) Notes: VIL VIL A9 = VH A0 = VIH or VIL A1 - A17 = VIL 1. X can be VIL or VIH. 2. Read, output disable, and standby modes require, 2.7V ≤ VCC ≤ 3.6V, or 4.5V ≤ VCC ≤ 5.5V. 3. Refer to the programming characteristics tables in this data sheet. 4. VH = 12.0 ± 0.5V. 5. Two identifier words may be selected. All Ai inputs are held low (VIL) except A9,which is set to VH , and A0, which is toggled low (VIL) to select the Manufacturer’s Identification word and high (VIH) to select the Device Code word. 6. Standby VCC current (ISB) is specified with VPP = VCC . VCC > VPP will cause a slight increase in ISB. 3 DC and AC Operating Conditions for Read Operation AT27BV400 Com. -12 -15 0°C - 70°C 0°C - 70°C -40°C - 85°C -40°C - 85°C 2.7V to 3.6V 2.7V to 3.6V 5V ± 10% 5V ± 10% Operating Temperature (Case) Ind. VCC Power Supply DC and Operating Characteristics for Read Operation Symbol Parameter Condition Min Max Units VCC = 2.7V to 3.6V ILI ILO IPP1 (2) Input Load Current VIN = 0V to VCC ±1 µA Output Leakage Current VOUT = 0V to VCC ±5 µA VPP = VCC 10 µA ISB1 (CMOS), CE = VCC ± 0.3V 20 µA ISB2 (TTL), CE = 2.0 to VCC + 0.5V 100 µA f = 5MHz, IOUT = 0 mA, CE = VIL, VCC = 3.6V 10 mA VPP (1) Read/Standby Current ISB VCC(1) Standby Current ICC VCC Active Current VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage VOH Output High Voltage VCC = 3.0 to 3.6V -0.6 0.8 V VCC = 2.7 to 3.6V -0.6 0.2 x VCC V VCC = 3.0 to 3.6V 2.0 VCC + 0.5 V VCC = 2.7 to 3.6V 0.7 x VCC VCC + 0.5 V IOL = 2.0 mA 0.4 V IOL = 100 µA 0.2 V IOL = 20 µA 0.1 V IOH = -2.0 mA 2.4 V IOH = -100 µA VCC - 0.2 V IOH = -20 µA VCC - 0.1 V VCC = 4.5V to 5.5V ILI ILO IPP1 (2) Input Load Current VIN = 0V to VCC ±1 µA Output Leakage Current VOUT = 0V to VCC ±5 µA VPP = VCC 10 µA ISB1 (CMOS), CE = VCC ± 0.3V 100 µA ISB2 (TTL), CE = 2.0 to VCC + 0.5V 1 mA f = 5 MHz, IOUT = 0 mA, CE = VIL 40 mA VPP (1) Read/Standby Current ISB VCC(1) Standby Current ICC VCC Active Current VIL Input Low Voltage -0.6 0.8 V VIH Input High Voltage 2.0 VCC + 0.5 V VOL Output Low Voltage I OH = 2.1 mA 0.4 V VOH Output High Voltage IOH = -400 µA Notes: 2.4 V 1. VCC must be applied simultaneously or before VPP, and removed simultaneously or after VPP. 2. VPP may be connected directly to VCC except during programming. The supply current would then be the sum of ICC and IPP. 4 AT27BV400 AT27BV400 AC Characteristics for Read Operation VCC = 2.7V to 3.6V and 4.5V to 5.5V AT27BV400 -12 Symbol Parameter Condition tACC(2) tCE Min -15 Max Min Max Units Address to Output Delay CE = OE = VIL 120 150 ns (2) CE to Output Delay OE = VIL 120 150 ns (2)(3) OE to Output Delay CE = VIL 40 50 ns 30 35 ns tOE tDF(4)(5) OE or CE High to Output Float, whichever occured first tOH(4) Output Hold from Address CE or OE, whichever occured first tST BYTE High to Output Valid 120 150 ns BYTE Low to Output Transition 50 60 ns tSTD Notes: 5 5 ns 1. 2,3,4,5. See the AC Waveforms for Read Operation diagram. Byte-Wide Read Mode AC Waveforms Note: BYTE/VPP = VIL Word-Wide Read Mode AC Waveforms Note: BYTE/VPP = VIH 5 BYTE Transition AC Waveforms Notes: 1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE. 3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC. 4. This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. Input Test Waveforms and Measurement Levels Output Test Load tR, tF < 20 ns (10% to 90%) Note: CL = 100 pF including jig capacitance. Pin Capaticance f = 1 MHz, T = 25°C(1) Typ Max Units Conditions CIN 4 10 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 6 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27BV400 AT27BV400 Programming Waveforms(1) Notes: 1. The Input Timing reference is 0.8V for VIL and 2.0V for VIH. 2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer. 3. When programming the AT27BV400, a 0.1 µF capacitor is required across VPP and ground to suppress voltage transients. DC Programming Characteristics TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V Limits Symbol Parameter Test Conditions ILI Input Load Current VIN = VIL, VIH VIL Input Low Level VIH Input High Level VOL Output Low Voltage IOL = 2.1 mA VOH Output High Voltage IOH = -400 µA ICC2 VCC Supply Current (Program and Verify) IPP2 VPP Supply Current VID A9 Product Identification Voltage Min Max Units ±10 µA -0.6 0.8 V 2.0 VCC + 0.5 V 0.4 V 2.4 CE = VIL 11.5 V 50 mA 30 mA 12.5 V 7 AC Programming Characteristics TA = 25 ± 5°C, VCC = 6.5 ± 0.25V, VPP = 13.0 ± 0.25V Limits Test Conditions(1) Symbol Parameter tAS Address Setup Time tOES OE Setup Time tDS Data Setup Time tAH Address Hold Time tDH Data Hold Time tDFP OE High to Output Float Delay(2) tVPS VPP Setup Time tVCS VCC Setup Time Input Rise and Fall Times: (10% to 90%) 20 ns 2 µs 2 µs 0 µs 2 µs 0 Output Timing Reference Level: 0.8V to 2.0V CE Program Pulse Width tOE Data Valid from OE tPRT BYTE /VPP Pulse Rise Time During Programming Units µs Input Timing Reference Level: 0.8V to 2.0V (3) Max 2 Input Pulse Levels: 0.45V to 2.4V tPW Notes: Min 130 ns 2 µs 2 µs 47.5 52.5 µs 150 ns 50 ns 1. Vcc must be applied simultaneously or before VPP and removed simultaneously or after VPP. 2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven— see timing diagram. 3. Program Pulse width tolerance is 50 µsec ± 5%. Atmel’s 27BV800 Integrated Product Identification Code(1) Pins A0 Codes O14 O13 O12 O11 O10 O9 O8 O7 O6 O5 O4 O3 O2 O1 O0 Hex Data Manufacturer 0 0 0 0 1 1 1 1 0 1E1E Device Type 1 1 1 1 1 0 1 0 0 F4F4 Note: 8 O15 1. The AT27BV400 has the same Product Identification Code as the AT27C400. Both are programming compatible. AT27BV400 AT27BV400 Rapid Programming Algorithm A 50 µs CE pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and BYTE/VPP is raised to 13.0V. Each address is first programmed with one 50 µs CE pulse without verification. Then a verification/reprogramming loop is executed for each address. In the event a word fails to pass verification, up to 10 successive 50 µs pulses are applied with a verification after each pulse. If the word fails to verify after 10 pulses have been applied, the part is considered failed. After the word verifies properly, the next address is selected until all have been checked. VPP is then lowered to 5.0V and VCC to 5.0V. All words are read again and compared with the original data to determine if the device passes or fails. 9 Ordering Information ICC (mA) tACC (ns) Active Standby 120 10 150 Ordering Code Package 0.02 AT27BV400-12JC AT27BV400-12RC AT27BV400-12TC 44J 44R 48T Commercial (0°C to 70°C) 10 0.02 AT27BV400-12JI AT27BV400-12RI AT27BV400-12TI 44J 44R 48T Industrial (-40°C to 85°C) 10 0.02 AT27BV400-15JC AT27BV400-15RC AT27BV400-15TC 44J 44R 48T Commercial (0°C to 70°C) 10 0.02 AT27BV400-15JI AT27BV400-15RI AT27BV400-15TI 44J 44R 48T Industrial (-40°C to 85°C) Package Type 44J 44-Lead, Plastic J-Leaded Chip Carrier (PLCC) 44R 44-Lead, 0.450" Wide, Plastic Gull Wing Small Outline Package (SOIC/SOP) 48T 48-Lead, Plastic Thin Small Outline Package (TSOP) 12 x 20 mm 10 AT27BV400 Operation Range AT27BV400 Packaging Information 44R, 44-Lead, 0.450" Wide, Plastic Gull Wing Small Outline Package (SOIC) Dimensions in Inches and (Millimeters) 48T, 48-Lead, 12 x 20 mm, Plastic Thin Small Outline Package(TSOP) Dimensions in Millimeters and (Inches)* *Controlling dimension: millimeters 44J, 44-Lead, Plastic J-Leaded Chip Carrier (PLCC) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-018 AC .045(1.14) X 45° PIN NO. 1 IDENTIFY .045(1.14) X 30° - 45° .012(.305) .008(.203) .630(16.0) .590(15.0) .656(16.7) SQ .650(16.5) .032(.813) .026(.660) .695(17.7) SQ .685(17.4) .050(1.27) TYP .500(12.7) REF SQ .021(.533) .013(.330) .043(1.09) .020(.508) .120(3.05) .090(2.29) .180(4.57) .165(4.19) .022(.559) X 45° MAX (3X) 11