Series JF Ultra-Thin Process Sealed Tactiles Distinctive Characteristics Extremely low profile of .224” (5.7mm) from PCB to top of switch. Red, green, or yellow LED with spot or full face illumination. Rubber seal construction prevents contact contamination and allows automated soldering and cleaning. Minimal operating force and short stroke permit light touch operation. Dome contact gives crisp tactile and audible feedback to positively indicate circuit transfer and assures high reliability and long life. Space saving body dimensions provide for compact, side-by-side mounting on a standard grid. Actual Size Crimped terminals ensure secure mounting and prevent dislodging during wave soldering. Terminal spacing conforms to standard .100” (2.54mm) PCB grid. Matching indicator available and shown at the end of Section M. Common Bus Matrix X-Y Matrix These single pole, single throw switches can be used in a keyboard matrix and, using strapped terminals, achieve a common bus electrical configuration on a single-sided PC board. These single pole, single throw switches can be arranged on a single-sided PC board matrix with strapped terminals to achieve an X-Y type electrical interconnection. 9 5 4 6 10 6 4 7 8 9 3 11 8 A B 0 1 2 7 12 1 2 3 4 5 6 7 8 9 0 A B P C Te r m i n a t i o n s 1 2 3 4 5 6 7 8 9 10 11 12 13 1 5 4 6 2 7 8 9 6 A B 0 7 = ON Blue = PCB Trace 5 4 3 Keys (Switches) 3 2 1 3 2 1 13 Keys (Switches) 5 P C Te rminations 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 0 A B = ON Black = Switch Circuit NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Ultra-Thin Process Sealed Tactiles Series JF General Specifications Electrical Capacity (Resistive Load) Low Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Total Travel: Materials & Finishes Actuator: Case: Seal: Base: Movable Contact: Stationary Contacts: Terminals: Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: PCB Processing Soldering: Cleaning: Standards & Certifications UL Recognition or CSA Certification: 50mA @ 24V DC 50 milliohms maximum 500 megohms minimum @ 250V DC 250V AC minimum for 1 minute minimum 500,000 operations minimum 500,000 operations minimum 3.0N for flush actuator 2.0N for sculptured actuator Flush Actuators .016” (0.4mm); Sculptured Actuator: .031” (0.8mm) Polyamide for spot illuminated; polycarbonate for full face Glass fiber reinforced polyamide Nitrile butadiene rubber Glass fiber reinforced polyester Phosphor bronze with silver plating Brass with silver plating Brass with silver plating –25°C through +70°C (–13°F through +158°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering recommended. See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. Automated cleaning. See Cleaning specifications in Supplement section. Switches should not be operated or have any pressure on the actuators during cleaning. Full face illuminated models suitable only for bottom board spray wash to avoid contamination of the 2-layered actuator, which may compromise the aesthetics. The JF Series tactiles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Ultra-Thin Process Sealed Tactiles Series JF TYPICAL SWITCH ORDERING EXAMPLE JF 15 R P 2 POLE & CIRCUIT 15 SPST OFF C LED COLORS ACTUATOR TYPES 1 Square C Red TERMINALS 2 Round E Yellow Straight PC 3 Sculptured F Green (ON) ( ) = Momentary C P ILLUMINATION R Spot A Full Face (with square actuator only) ACTUATOR COLORS Spot Illuminated C Red D Orange F Green G Blue H Gray *Full Face Illuminated DESCRIPTION FOR TYPICAL ORDERING EXAMPLE C Red E Yellow F Green *LED color must match actuator color. JF15RP2CC Red LED for Spot Illumination Round Red Actuator SPST OFF-(ON) Circuit Straight PC Terminals POLE & CIRCUIT Actuator Position ( ) = Momentary Normal Pole SP SPST OFF LED Schematic Down Model JF15 Switch Throw & Schematic (ON) 1 3 2 4 (+) (-) Notes: Terminal numbers are shown on switch. LED circuit is isolated & requires external power source. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series JF Ultra-Thin Process Sealed Tactiles ILLUMINATION & ACTUATOR TYPES R Spot Illumination 1 Square Actuator 2 Round Actuator 3 Sculptured Actuator Actuator Colors Available: C, D, F, G, H Housing is black C Color Codes: D Red Orange E A Full Face Illumination 1 Square Actuator Actuator Colors Available: C, E, F Housing is black F Yellow G Green H Blue Gray Flexible Panel Design Versatile panel arrangements can be made to fit individual design needs. (1.7) .067 (5.72) .225 (5.08) .200 (3.6) .142 (22.86) .900 (6.0) Min .236 Spot Illumination (1.04) .041 (3.6) .142 (17.78) Typ .700 (27.94) 1.100 (7.3) .287 (6.7) .264 (3.0) .118 Full Face Illumination (17.78) Typ .700 TERMINALS P LED polarity marking Straight PC Terminals With isolated lamp circuit Further details in Typical Switch Dimensions LED COLORS & SPECIFICATIONS LEDs are supplied as an integral part of the switch. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section. Spot Illumination Color C Red Yellow E Full Face Illumination Green F C Red Yellow E F Green Forward Peak Current I FM 40mA 40mA 40mA 30mA 30mA 30mA Continuous Forward Current IF 30mA 30mA 30mA 20mA 20mA 20mA Forward Voltage VF 1.7V 2.2V 2.2V 1.77V 2.1V 2.3V Reverse Peak Voltage VRM 4V 4V 4V 4V 4V 4V Current Reduction Rate Above 25°C ∆I F 0.67mA/°C 0.67mA/°C 0.67mA/°C 0.4mA/°C 0.4mA/°C 0.4mA/°C Ambient Temperature Range –25° ~ +70°C –25° ~ +70°C NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Ultra-Thin Process Sealed Tactiles Series JF TYPICAL SWITCH DIMENSIONS Spot Illuminated with Square Actuator (6.0) Min .236 (5.7) .225 (2.2) .087 (5.6) .220 (1.6) .063 (3.0) .118 (3.8) .150 (5.08) .200 (0.2) Typ .008 (0.5) .020 + (14.0) Sq .551 JF15RP1CC Spot Illuminated with Round Actuator (8.68) .342 (5.6) .220 (1.6) .063 (3.0) .118 (3.8) .150 4 4 (5.08) .200 (0.2) Typ .008 (0.5) .020 (14.0) Dia .551 Spot Illuminated with Sculptured Actuator (2.2) .087 (8.68) .342 (1.6) .063 3 3 1 (5.7) .225 (3.8) .150 (3.0) .118 (0.3) Typ .012 (3.6) .142 4 4 (0.8) Typ .031 (10.16) .400 JF15RP3CC Full Face Illuminated with Square Actuator (1.7) .067 (8.68) .342 (13.5) .531 3 1 1 (6.0) .236 4 4 (0.3) Typ .012 (3.6) .142 (3.0) Min .118 (3.0) .118 (0.5) Sq .020 (1.0) Dia Typ .039 (5.08) .200 + + – (5.08) .200 (10.16) .400 1 3 (10.16) .400 (26.9) (7.3) 1.059 .287 (13.0) Sq .512 (12.7) .500 (0.3) .012 (17.7) .697 2 4 (10.3) .406 (0.3) Typ .012 (3.6) .142 4 2 (16.4) .646 1 3 (12.7) .500 (8.85) .348 (8.2) .323 (5.08) .200 2 (10.16) .400 (0.8) Typ .031 (10.16) .400 – JF15AP1CC 3 (5.08) .200 (12.7) .500 2 (0.3) .012 (7.3) .287 (2.7) .106 _ (12.7) .500 (14.0) Sq .551 (16.4) Sq .646 (17.7) .697 (1.0) Dia Typ .039 (5.08) .200 (0.2) Typ .008 (6.0) Min .236 (0.5) .020 (5.08) .200 (13.95) .549 (11.43) .450 (5.08) .200 2 (10.16) .400 + (8.85) .348 (5.08) .200 (12.7) .500 2 (5.6) .220 _ (12.7) .500 (0.3) .012 (16.4) Sq .646 (17.7) .697 JF15RP2CC 1 (5.08) .200 (8.85) .348 (1.0) Dia Typ .039 (0.8) Typ .031 (10.16) .400 + (13.95) .549 (11.43) .450 (5.08) .200 2 (10.16) .400 (6.0) Min .236 (5.7) .225 (2.2) .087 1 (12.7) .500 (0.3) Typ .012 (3.6) .142 (0.3) .012 (16.4) Sq .646 (17.7) .697 (5.08) .200 (12.7) .500 2 (8.85) .348 3 3 (5.08) .200 (11.43) .450 1 (13.95) .549 _ (10.16) .400 (1.0) Dia Typ .039 (0.8) Typ .031 (10.16) .400 NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Ultra-Thin Process Sealed Tactiles Series JF LEGENDS LM Easily create and submit your own legends using our new on-line Legend Maker. Visit www.nkkswitches.com For other legend support options, customers may either contact the factory and request the JF Legend Packet, or utilize the general information and basic specifications presented below. Suggested Printable Area ER W PO O D N N ER N W O O W PO (13.5) .531 (11.98) .472 (6.0) .236 (4.48) .176 (1.52) Typ .060 (8.03) .316 (12.48) Sq .491 (14.0) Sq .551 (0.76) Typ .030 (12.48) Dia .491 (14.0) Dia .551 (0.76) Typ .030 (0.76) Typ .030 (0.76) Typ .030 (4.98) .196 (9.6) .378 (11.13) .438 (0.76) Typ .030 (11.48) Sq .452 (13.0) Sq .512 (0.76) Typ .030 Recommended Print Method: Screen Print or Pad Print Shaded areas are printable areas. Epoxy based ink is recommended. Additional Methods Engraving is not recommended as an additional method for legends. Contact factory if engraving is required; it must be done before the actuator is assembled. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07