LINER LT1568 Very low noise, high frequency active rc, filter building block Datasheet

LT1568
Very Low Noise,
High Frequency Active RC,
Filter Building Block
DESCRIPTIO
U
FEATURES
■
■
■
■
■
■
■
■
■
■
■
Up to 10MHz Center Frequency on a Single 3V
Supply
Easy to Use—A Single Resistor Value Sets Lowpass
Cutoff Frequency (200kHz ≤ ƒC ≤ 5MHz), Unequal
Resistor Values Extend Cutoff Frequency Up to
10MHz
Extremely Flexible—Different Resistor Values
Allow Lowpass Transfer Functions with or Without
Gain (Butterworth, Chebyshev or Custom)
SNR = 92dB (ƒC = 2MHz, 2VP-P)
THD = –84dB (ƒC = 2MHz, 1VP-P)
Internal Capacitors Trimmed to ±0.75%
Single 4-Pole Lowpass Filter or Matched Pair of
2-Pole Lowpass Filters
Can be Connected as a Bandpass Filter
Single-Ended or Differential Output
Operates from Single 3V (2.7V Min) to ±5V Supply
Rail-to-Rail Input and Output Voltages
U
APPLICATIO S
■
■
■
■
■
Replaces Discrete RC Active Filters and LC Filter
Modules
Antialiasing/Reconstruction Filters
Dual or I-and-Q Channels (Two Matched 2nd Order
Filters in One Package)
Single-Ended to Differential Conversion
Video Signal Processing
The LT®1568 is an easy-to-use, active-RC filter building
block with rail-to-rail inputs and outputs. The internal capacitors of the IC and the GBW product of the internal low
noise op amps are trimmed such that consistent and repeatable filter responses can be achieved. With a single resistor value, the LT1568 provides a pair of matched 2-pole
Butterworth lowpass filters with unity gain suitable for I/Q
channels.
By using unequal-valued external resistors, the two 2-pole
sections can create different frequency responses or
gains. In addition, the two stages may be cascaded to
create a single 4-pole filter with a programmable response. Capable of cutoff frequencies up to 10MHz, the
LT1568 is ideal for antialiasing or channel filtering in high
speed data communications systems. The LT1568 can
also be used as a bandpass filter.
The LT1568 features very low noise, supporting signal-tonoise ratios of over 90dB. It also provides single-ended to
differential signal conversion for directly driving high
speed A/D converters. The LT1568 has a shutdown mode
that reduces supply current to approximately 0.5mA on a
5V supply.
The LT1568 is available in a narrow 16-lead SSOP
package.
, LTC and LT are registered trademarks of Linear Technology Corporation.
U
TYPICAL APPLICATIO
Amplitude and Phase Matched Dual Butterworth 2.5MHz Lowpass
Filter with Differential Output. Single 3V Supply Operation
Amplitude Response
3
0
3V
–3
0.1µF
511Ω
VINA
2
3
VOUTA
VOUTA
4
511Ω
5
6
0.1µF 7
8
16
V+
LT1568
15
INVA
INVB
14
SA
SB
13
OUTA
OUTB
12
OUTA
OUTB
11
GNDA GNDB
10
NC
EN
9
V–
V–
V+
511Ω
–6
511Ω
VINB
GAIN (dB)
1
511Ω
VOUTB
511Ω
1568 TA01
VOUTB
–9
–12
–15
–18
THE PROPRIETARY ARCHITECTURE
ALLOWS FOR A SIMPLE RESISTOR
CALCULATION:
10MHz
R = 128Ω •
; ƒC = CUTOFF FREQUENCY
ƒ
C
–21
–24
–27
100k
1M
FREQUENCY (Hz)
10M
1568 TA02
1568f
1
LT1568
W W
W
AXI U
U
ABSOLUTE
RATI GS
U
U
W
PACKAGE/ORDER I FOR ATIO
(Note 1)
Total Supply Voltage (V + to V –) ........................... 11.6V
Input Voltage on INVA, INVB, GNDA and
GNDB Pins ....................................................... V + to V –
Input Current on INVA, INVB, GNDA and
GNDB Pins (Note 2) ........................................... ±10mA
Output Short-Circuit Duration on OUTA, OUTB, OUTA
and OUTB Pins ............................................... Indefinite
Maximum Continuous Output Current (Note 3)
DC ............................................................... ±100mA
Specified Temperature Range (Note 9)
LT1568C ............................................ – 40°C to 85°C
LT1568I ............................................. – 40°C to 85°C
Junction Temperature .......................................... 150°C
Storage Temperature Range ................ – 65°C to 150°C
Lead Temperature (Soldering, 10 sec)................. 300°C
ORDER PART
NUMBER
TOP VIEW
V+
1
16 V +
INVA
2
15 INVB
SA
3
14 SB
OUTA
4
13 OUTB
OUTA
5
12 OUTB
GNDA
6
11 GNDB
NC
7
10 EN
V–
8
9
LT1568CGN
LT1568IGN
GN PART
MARKING
V–
1568
1568I
GN PACKAGE
16-LEAD PLASTIC SSOP
TJMAX = 150°C, θJA = 135°C/W
Consult LTC Marketing for parts specified with wider operating temperature ranges.
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications and typical values are at TA = 25°C. VS = single 5V, EN pin to logic “low,” RL = 400Ω,
connected to midsupply, RFIL = R11 = R21 = R31 = R12 = R22 = R32, unless otherwise noted (see Block Diagram).
SYMBOL
PARAMETER
VS
Total Supply Voltage
IS
Supply Current
VS = 3V
VS = 5V
VS = ±5V
●
●
●
Shutdown Supply Current
VS = 3V, VEN = 2.4V
VS = 5V, VEN = 4.4V
VS = ±5V, VEN = 4.4V
●
●
●
Output Voltage Swing High
(OUTA, OUTA, OUTB, OUTB Pins)
VS = 3V, RFIL = 1.28k, RL = 1k
VS = 5V, RFIL = 1.28k, RL = 1k
VS = 5V, RFIL = 128Ω, RL = 400Ω
VS = ±5V, RFIL = 1.28k, RL = 1k
●
●
●
●
Output Voltage Swing Low
(OUTA, OUTA, OUTB, OUTB Pins)
VS = 3V, RFIL = 1.28k, RL = 1k
VS = 5V, RFIL = 1.28k, RL = 1k
VS = 5V, RFIL = 128Ω, RL = 400Ω
VS = ±5V, RFIL = 1.28k, RL = 1k
●
●
●
●
IOUT
CONDITIONS
MIN
●
TYP
2.7
2.75
4.60
4.50
4.60
MAX
11
V
24
26
28
35
36
38
mA
mA
mA
0.3
0.5
1.0
1.0
1.3
2.5
mA
mA
mA
2.85
4.80
4.65
4.75
0.05
0.07
0.20
V
V
V
V
0.12
0.15
0.40
–4.7
±80
Maximum Output Current
UNITS
V
V
V
V
mA
Op Amp Input Offset Voltage
VS = 3V
VS = 5V
VS = ±5V
●
●
●
–2.5
–2.5
–2.0
–0.5
0.2
1.2
1.5
2.5
4.5
mV
mV
mV
Inverter Output Offset Voltage
VS = 3V
VS = 5V
VS = ±5V
●
●
●
–2
–10
–12
2.5
0.6
–4.0
7.0
4.5
2.0
mV
mV
mV
1568f
2
LT1568
ELECTRICAL CHARACTERISTICS
The ● denotes the specifications which apply over the full operating
temperature range, otherwise specifications and typical values are at TA = 25°C. VS = single 5V, EN pin to logic “low,” RL = 400Ω,
connected to midsupply, RFIL = R11 = R21 = R31 = R12 = R22 = R32, unless otherwise noted (see Block Diagram).
SYMBOL
PARAMETER
CONDITIONS
MIN
IB
Op Amp Input Bias Current
VS = 3V
VS = 5V
VS = ±5V
●
●
●
Inverter Gain (Sections A and B, Note 5)
Frequency = DC
Frequency = 2MHz
Frequency = 10MHz
●
Inverter Phase Shift (Sections A and B,
Note 5)
Frequency = DC
Frequency = 2MHz
Frequency = 10MHz
Inverter Bandwidth (Note 4)
Slew Rate (OUTA, OUTB, OUTA,
OUTB) Pins
VCM
Common Mode Input Voltage Range
(GNDA and GNDB Pins, Note 6)
VS = 3V
VS = ±5V
Single Supply GND Reference Voltage
VS = 5V, GNDA Tied to GNDB
EN Input Logic Low Level
VS = 3V, 5V or ±5V
EN Input Logic High Level
VS = 3V, 5V or ±5V
VIH
tEN
0.5
0.4
–0.2
2
2
2
–0.2
0.01
0.01
0.27
UNITS
µA
µA
µA
MHz
0.2
dB
dB
dB
180
179
176
DEG
DEG
DEG
53
V/µs
1 to 1.9
–3.4 to 2.7
V
V
2.5
●
V
V + – 2.1
●
EN Input Pull-Up Resistor
tDIS
MAX
55
SR
VIL
TYP
V+
V
– 0.6
30
V
40
kΩ
Disable (Shutdown) Time
EN Pin Steps from 0V to V+
20
µs
Enable (Start-Up) Time
EN Pin Steps from V+ to 0V
100
µs
FILTER ELECTRICAL CHARACTERISTICS
Specifications are for the output (OUTA or OUTB) of a single 2nd order section (A or B) with respect to VGND = VGNDA = VGNDB,
gain = –1, RFIL = R11 = R21 = R31 = R12 = R22 = R32, (see Block Diagram). The ● denotes the specifications which apply over the
full operating temperature range, otherwise specifications and typical values are at TA = 25°C. VS = single 5V, EN pin to logic “low,”
RL = 400Ω, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
ADC
DC Gain
VOS(OUT)
DC Offset Voltage
(VOUTA – VGNDA) or (VOUTB – VGNDB)
VS = 3V, fC = 1MHz, RFIL = 1.28k
VS = 5V, fC = 1MHz, RFIL = 1.28k
VS = ±5V, fC = 1MHz, RFIL = 1.28k
∆VOS(OUT)
DC Offset Voltage Mismatch
(VOUTA – VGNDA) – (VOUTB – VGNDB)
VS = 3V, fC = 1MHz, RFIL = 1.28k
VS = 5V, VS = ±5V, fC = 1MHz, RFIL = 1.28k
MIN
TYP
MAX
UNITS
●
–1.01
–1
–0.99
V/V
●
●
●
–5
–10
–12
2.6
0.6
–4.0
15
10
4
mV
mV
mV
●
●
–8
–10
±4
±4
8
10
mV
mV
●
0.2
Transfer Function Characteristics for Each Section (A or B) to Single-Ended Output (OUTA or OUTB)
fC
Cutoff Frequency Range (Note 7)
TC
Cutoff Frequency Temperature Coefficient
VS = 3V, VS = 5V, VS = ±5V
●
10
±1
MHz
ppm/°C
1568f
3
LT1568
FILTER ELECTRICAL CHARACTERISTICS
Specifications are for the output (OUTA or OUTB) of a single 2nd order section (A or B) with respect to VGND = VGNDA = VGNDB,
gain = –1, RFIL = R11 = R21 = R31 = R12 = R22 = R32, (see Block Diagram). The ● denotes the specifications which apply over the
full operating temperature range, otherwise specifications and typical values are at TA = 25°C. VS = single 5V, EN pin to logic “low,”
RL = 400Ω connected to midsupply, unless otherwise noted.
SYMBOL
THD
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Filter Gain, fC = 1MHz,
VS = 5V, RFIL = 1.28k
(Measured with Respect to DC Gain)
Test Frequency = 300kHz (0.3 • fC)
Test Frequency = 750kHz (0.75 • fC)
Test Frequency = 1MHz (1 • fC)
Test Frequency = 2MHz (2 • fC)
Test Frequency = 4MHz (4 • fC)
●
●
●
●
–0.05
–1.45
–3.60
–13.7
0.05
–1.20
–3.20
–13.2
–25.0
0.25
–0.85
–2.80
–12.5
dB
dB
dB
dB
dB
Filter Gain, fC = 10MHz,
VS = 5V, RFIL = 128Ω
(Measured with Respect to DC Gain)
Test Frequency = 1MHz (0.1 • fC)
Test Frequency = 7.5MHz (0.75 • fC)
Test Frequency = 10MHz (1 • fC)
Test Frequency = 20MHz (2 • fC)
Test Frequency = 40MHz (4 • fC)
●
●
●
●
–0.1
–1.5
–3.5
–14.2
0.02
–1.0
–3.0
–13.2
–27.5
0.25
–0.50
–2.40
–12.2
dB
dB
dB
dB
dB
Filter Gain Mismatch
(VOUTA – VOUTB)
fC = 1MHz, fIN = fC
fC = 10MHz, fIN = fC
●
●
–0.25
–0.30
±0.02
±0.02
0.25
0.30
dB
dB
Wideband Output Noise
fC = 1MHz, RFIL = 1.28k, BW = 2MHz
fC = 10MHz, RFIL = 128Ω, BW = 20MHz
18
34
Total Harmonic Distortion
fC = 1MHz, RFIL = 1.28k,
fIN = 200kHz, VIN = 1VP-P
– 84
dB
fC = 10MHz, RFIL = 128Ω,
fIN = 2MHz, VIN = 1VP-P
– 69
dB
µVRMS
µVRMS
Specifications are for the OUTA or OUTB of a single 2nd order section (A or B) with respect to VGND = VGNDA = VGNDB, gain = 1,
RFIL = R11 = R21 = R31 = R12 = R22 = R32, (see Block Diagram) The ● denotes the specifications which apply over the full
operating temperature range, otherwise specifications and typical values are at TA = 25°C. VS = single 5V, EN pin to logic “low,”
RL = 400Ω connected to midsupply, unless otherwise noted.
SYMBOL
PARAMETER
ADC
DC Gain
VOS(OUT)
DC Offset Voltage
(VOUTA – VGNDA) or (VOUTB – VGNDB)
∆VOS(OUT)
DC Offset Voltage Mismatch
(VOUTA – VGNDA) – (VOUTB – VGNDB)
CONDITIONS
MIN
TYP
MAX
UNITS
●
0.99
1
1.01
V/V
VS = 3V, fC = 1MHz, RFIL = 1.28k
VS = 5V, VS = ±5V, fC = 1MHz, RFIL = 1.28k
●
●
–9
–10
–2
–1
5
10
mV
mV
VS = 3V, fC = 1MHz, RFIL = 1.28k
VS = 5V, VS = ±5V, fC = 1MHz, RFIL = 1.28k
●
●
–8
–10
±2
±2
8
10
mV
mV
●
0.2
10
MHz
Transfer Function Characteristics for Each Section (A or B) to Single-Ended Output (OUTA or OUTB)
fC
Cutoff Frequency Range (Note 7)
TC
Cutoff Frequency Temperature Coefficient
Filter Gain, fC = 1MHz,
VS = 5V, RFIL = 1.28k
(Measured with Respect to DC Gain)
VS = 3V, VS = 5V, VS = ±5V
±1
●
Test Frequency = 300kHz (0.3 • fC)
Test Frequency = 750kHz (0.75 • fC)
Test Frequency = 1MHz (1 • fC)
Test Frequency = 2MHz (2 • fC)
Test Frequency = 4MHz (4 • fC)
●
●
●
●
–0.10
–1.40
–3.50
–13.7
0.15
–1.00
–3.10
–13.0
–25.0
ppm/°C
0.40
–0.65
–2.60
–12.5
dB
dB
dB
dB
dB
1568f
4
LT1568
FILTER ELECTRICAL CHARACTERISTICS
Specifications are for the OUTA or OUTB of a single 2nd order section (A or B) with respect to VGND = VGNDA = VGNDB, gain = 1,
RFIL = R11 = R21 = R31 = R12 = R22 = R32, (see Block Diagram) The ● denotes the specifications which apply over the full
operating temperature range, otherwise specifications and typcial values are at TA = 25°C. VS = single 5V, EN pin to logic “low,”
RL = 400Ω connected to midsupply, unless otherwise noted.
SYMBOL
THD
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
Filter Gain, fC = 10MHz,
VS = 5V, RFIL = 128Ω
(Measured with Respect to DC Gain)
Test Frequency = 1MHz (0.1 • fC)
Test Frequency = 7.5MHz (0.75 • fC)
Test Frequency = 10MHz (1 • fC)
Test Frequency = 20MHz (2 • fC)
Test Frequency = 40MHz (4 • fC)
●
●
●
●
–0.3
–1.2
–3.1
–12.2
0.15
–0.50
–2.30
–11.2
–19.1
0.5
0.0
–1.5
–10.2
dB
dB
dB
dB
dB
Filter Gain Mismatch
(VOUTA – VOUTB)
fC = 1MHz, fIN = fC
fC = 10MHz, fIN = fC
●
●
–0.4
–0.5
±0.02
±0.02
0.4
0.5
dB
dB
Wideband Output Noise
fC = 1MHz, RFIL = 1.28k, BW = 2MHz
fC = 10MHz, RFIL = 128Ω, BW = 20MHz
22
60
µVRMS
µVRMS
Total Harmonic Distortion
fC = 1MHz, RFIL = 1.28k,
fIN = 200kHz, VIN = 1VP-P
– 84
dB
fC = 10MHz, RFIL = 128Ω,
fIN = 2MHz, VIN = 1VP-P
– 75
dB
Specifications are for the differential output (OUTA – OUTA or OUTB – OUTB) of a single 2nd order section (A or B), gain = –2,
RFIL = R11 = R21 = R31 = R12 = R22 = R32. All voltages are with respect to VGND = VGNDA = VGNDB. The ● denotes the specifications
which apply over the full operating temperature range, otherwise specifications and typical values are at TA = 25°C.
VS = single 5V, EN pin to logic “low,” RLDIFF = 800Ω connected at midsupply, unless otherwise noted.
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
ADC
DC Gain
VOS(OUT)
DC Offset Voltage
(OUTA – OUTA) or (OUTB – OUTB)
VS = 3V, fC = 1MHz, RFIL = 1.28k
VS = 5V, fC = 1MHz, RFIL = 1.28k
VS = ±5V, fC = 1MHz, RFIL = 1.28k
●
●
●
–4
–12
–20
6
2
–5
16
15
10
mV
mV
mV
∆VOS(OUT)
DC Offset Voltage Mismatch
(OUTA – OUTA) – (OUTB – OUTB)
VS = 3V, fC = 1MHz, RFIL = 1.28k
VS = 5V, fC = 1MHz, RFIL = 1.28k
VS = ±5V, fC = 1MHz, RFIL = 1.28k
●
●
●
–8
–12
–15
2
–2
2
8
12
15
mV
mV
mV
–2
●
UNITS
V/V
Transfer Function Characteristics for Each Section (A or B) to Differential Output (OUTA – OUTA or OUTB – OUTB)
fC
Cutoff Frequency Range (Note 7)
TC
Cutoff Frequency Temperature Coefficient
VS = 3V, VS = 5V, VS = ±5V
●
0.2
10
±1
●
MHz
ppm/°C
Filter Gain, fC = 1MHz,
VS = 5V, RFIL = 1.28k (Note 8)
(Measured with Respect to DC Gain)
Test Frequency = 300kHz (0.3 • fC)
Test Frequency = 750kHz (0.75 • fC)
Test Frequency = 1MHz (1 • fC)
Test Frequency = 2MHz (2 • fC)
Test Frequency = 4MHz (4 • fC)
●
●
●
●
–0.05
–1.40
–3.60
–13.7
0.10
–1.10
–3.20
–13.1
–25.0
0.25
–0.80
–2.70
–12.5
dB
dB
dB
dB
dB
Filter Gain, fC = 10MHz,
VS = 5V, RFL = 128Ω (Note 8)
(Measured with Respect to DC Gain)
Test Frequency = 1MHz (0.1 • fC)
Test Frequency = 7.5MHz (0.75 • fC)
Test Frequency = 10MHz (1 • fC)
Test Frequency = 20MHz (2 • fC)
Test Frequency = 40MHz (4 • fC)
●
●
●
●
–0.20
–1.30
–3.30
–13.1
0.1
–0.8
–2.6
–12.1
–24.3
0.30
–0.20
–1.90
–11.1
dB
dB
dB
dB
dB
1568f
5
LT1568
FILTER ELECTRICAL CHARACTERISTICS
Specifications are for the differential output (OUTA – OUTA or OUTB – OUTB) of a single 2nd order section (A or B), gain = –2,
RFIL = R11 = R21 = R31 = R12 = R22 = R32. All voltages are with respect to VGND = VGNDA = VGNDB. The ● denotes the specifications
which apply over the full operating temperature range, otherwise specifications and typical values are at TA = 25°C.
VS = single 5V, EN pin to logic “low,” RLDIFF = 800Ω connected to midsupply, unless otherwise noted.
SYMBOL
THD
PARAMETER
CONDITIONS
Filter Gain Mismatch
(VOUTA – VOUTA) – (VOUTB – VOUTB)
fC = 1MHz, fIN = fC
fC = 10MHz, fIN = fC
Wideband Output Noise
fC = 1MHz, RFIL = 1.28k, BW = 2MHz
fC = 10MHz, RFIL = 128Ω, BW = 20MHz
36
88
Total Harmonic Distortion
fC = 1MHz, RFIL = 1.28k,
fIN = 200kHz, VIN = 1VP-P
– 84
dB
fC = 10MHz, RFIL = 128Ω,
fIN = 2MHz, VIN = 1VP-P
– 69
dB
Note 1: Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2: The inputs of each op amp are protected by back-to-back diodes.
If either differential input voltage exceeds 1.4V, the input current should be
limited to less than 10mA.
Note 3: A heat sink may be required to keep the junction temperature
below the absolute maximum rating when the output is shorted
indefinitely.
Note 4: The inverter bandwidth is measured with the SA or SB output
floating, and is defined as the frequency at which the phase shift from
OUTA (OUTB) to OUTA (OUTB) drops from 180° to 135°.
Note 5: Measured with the SA or SB output connected in the filter
application circuit as shown in the Block Diagram.
Note 6: The common mode input voltage range is measured by shorting
the filter input to the common mode reference (GNDA or GNDB) and
applying a DC input voltage to search for the common mode voltage range
that creates a ±2mV (VS = 3V) or ±5mV (VS = ±5V) change in the (OUTA
or OUTB) voltage (measured with respect to GNDA or GNDB).
●
●
MIN
TYP
MAX
UNITS
–0.3
–0.4
±0.10
±0.15
0.3
0.4
dB
dB
µVRMS
µVRMS
Note 7: The minimum cutoff frequency of the LT1568 is arbitrarily listed
as 200kHz. The limit is arrived at by setting the maximum resistor value
limit at 6.4k. Due to input bias current, the output DC offset through a
single section can be as high as 25mV with resistors this large. The
LT1568 can be used with even larger resistors if the large offset voltages
can be tolerated. For cutoff frequencies below 200kHz, refer to the
LTC1563-2, LTC1563-3.
Note 8: With equal-sized resistors, the differential DC gain through either a
single section or cascaded sections is 6dB.
Note 9: The LT1568C is guaranteed to meet specified performance from
0°C to 70°C. The LT1568C is designed, characterized and expected to
meet specified performance from –40°C to 85°C but is not tested or QA
sampled at these temperatures. The LT1568I is guaranteed to meet
specified performance from –40°C to 85°C.
1568f
6
LT1568
U W
TYPICAL PERFOR A CE CHARACTERISTICS
Crosstalk vs Frequency
fCUTOFF = 1MHz
Supply Current vs Temperature
40
–50
–80
VIN = 2VP-P
VS = 5V
–85
–60
30
VS = 3V
CROSSTALK (dB)
VS = ±5V
VS = 5V
25
VIN = 2VP-P
VS = 5V
OUTA, OUTB
–90
CROSSTALK (dB)
ICC (mA)
35
Crosstalk vs Frequency
fCUTOFF = 10MHz
–95
–100
OUTA, OUTB
–105
–70
–80
OUTA, OUTB
–90
–110
OUTA, OUTB
20
–100
–115
50
0
25
TEMPERATURE (°C)
75 85
1k
10k
100k
1M
FREQUENCY (Hz)
10M
Distortion vs Frequency
VS = ±5V, fCUTOFF = 5MHz
–40
RL = 400Ω
–45 fIN = 2.5MHz
RL = 400Ω
–50 VIN = 1VP-P
–65
–50
2ND
–75
–80
3RD
DISTORTION (dB)
DISTORTION (dB)
DISTORTION (dB)
–55
–70
–60
–65
–70
2ND
–75
–80
–85
2ND
–70
3RD
–75
–90
1M
10M
1
0
2
3
4 5 6 7
OUTA (VP-P)
8
1568 G05
70
RL = 400Ω
fIN = 2.5MHz
–40
–50
DISTORTION (dB)
–55
–60
–65
2ND
–75
–50
–60
2ND
–70
3RD
3RD
Power Supply Rejection
vs Frequency
POWER SUPPLY REJECTION (dB)
–30
RL = 400Ω
–45 fIN = 2.5MHz
9 10 11
1568 G06
Distortion vs Output Voltage Swing
VS = 3V, fCUTOFF = 5MHz
–40
DISTORTION (dB)
–65
FREQUENCY (Hz)
Distortion vs Output Voltage Swing
VS = 5V, fCUTOFF = 5MHz
–80
–60
–85
–90
500k
1568 G04
–70
–55
–80
3RD
–85
5M
100M
Distortion vs Output Voltage Swing
VS = ±5V, fCUTOFF = 5MHz
–45
1M
FREQUENCY (Hz)
1M
10M
FREQUENCY (Hz)
1568 G03
Distortion vs Frequency
VS = ±5V, fCUTOFF = 10MHz
RL = 400Ω
VIN = 2VP-P
–90
200k
100k
1568 G02
1568 G01
–60
–110
10k
–120
15
–40 –25
–80
60
50
OUTA, OUTB
40
OUTA, OUTB
30
20
10
–85
–90
–90
0
1
2
3
4
OUTA (VP-P)
5
6
1568 G07
0
1
2
OUTA (VP-P)
3
4
1568 G08
0
10k
100k
1M
10M
FREQUENCY (Hz)
100M
1568 G09
1568f
7
LT1568
U
U
U
PI FU CTIO S
V+ (Pins 1, 16): The V+ positive supply voltage pins should
be tied together and bypassed with a 0.1µF capacitor to an
adequate analog ground plane using the shortest possible
wiring.
INVA, INVB (Pins 2, 15): Inverting Input. Each of the INV
pins is an inverting input of an op amp. Note that the INV
pins are high impedance, and are susceptible to coupling
of unintended signals. External parasitic capacitance on
the INV nodes will also affect the frequency response of
the filter sections. For these reasons, printed circuit connections to the INV pins must be kept as short as possible.
SA, SB (Pins 3, 14): Summing Pins. These pins are a
summing junction for input signals. Stray capacitance on
the SA or SB pins may cause “small” frequency errors of
the frequency response near the cutoff frequency (or
center frequency). The three external resistors for each
section should be located as close as possible to the SA or
SB pin to minimize stray capacitance (one picofarad of
stray capacitance may add up to 0.1% frequency error).
OUTA, OUTB (Pins 4, 13): Lowpass Output. These pins
are the rail-to-rail outputs of op amps. Each output is
designed to drive a nominal net load of 400Ω and 30pF.
OUTA, OUTB (Pins 5, 12): These pins are the inverted
versions of the OUTA and OUTB outputs respectively. Each
output is designed to drive a nominal load of 400Ω and
30pF.
GNDA (Pin 6): GNDA serves as the common mode reference voltage for section A. It should be tied to the analog
ground plane in a dual supply system. In a single-supply
system, an internal resistor divider can be used to establish a half-supply reference point. In that case, GNDA must
be bypassed to V– (Pins 8, 9) by a 0.1µF capacitor.
NC (Pin 7): This pin is not connected internally and can be
connected to ground.
V– (Pins 8, 9): The V– negative supply voltage pins should
be tied together and bypassed to GND by a 0.1µF capacitor
in a dual-supply system. In a single-supply system, tie
these pins to the ground plane.
EN (Pin 10): ENABLE. When the EN input goes high or is
open circuited, the LT1568 enters a shutdown state which
reduces the supply current to approximately 0.5mA
(VS = 5V). The OUTA, OUTB, OUTA and OUTB pins
assume high impedance states. GNDA will continue to be
biased at half-supply. If an input signal is applied to a
complete filter circuit while the LT1568 is in shutdown,
some signal will normally flow to the output through
passive components around the inactive IC.
EN is connected to V+ through an internal pull-up resistor
of approximately 40k. This defaults the LT1568 to the
shutdown state if the EN pin is left floating. Therefore, the
user must connect the EN pin to a voltage equal to or less
than (V + – 2.1)V to enable the part for normal operation.
(For example, if V+ is 5V, then to enable the part the EN pin
voltage should be 2.9V or less.)
GNDB (Pin 11): GNDB serves as the common mode
reference voltage for section B. It should be tied to the
analog ground plane in a dual supply system. In a singlesupply system, GNDB can be tied to GNDA to set the
common mode voltage at half-supply. If it is tied to
another reference voltage, GNDB should be bypassed to
V– (Pins 8, 9) by a 0.1µF capacitor.
1568f
8
LT1568
U
U
U
PI FU CTIO S
Dual Supply Power and Ground Connections
ANALOG
GROUND
PLANE
Single Supply Power and Ground Connections
ANALOG
GROUND
PLANE
V+
1
16
V+
V+
15
INVA
INVB
14
SA
SB
LT1568
13
OUTA OUTB
12
OUTA OUTB
11
GNDA GNDB
10
NC
EN
9
V–
V–
2
3
4
5
6
7
8
V–
V+
1
2
0.1µF
3
4
5
6
7
0.1µF
8
16
V+
V+
15
INVA
INVB
14
SA
SB
LT1568
13
OUTA OUTB
12
OUTA OUTB
11
GNDA GNDB
10
NC
EN
9
V–
V–
0.1µF
0.1µF
SINGLE POINT
SYSTEM GROUND
SINGLE POINT
SYSTEM GROUND
DIGITAL GROUND PLANE
(IF ANY)
DIGITAL GROUND PLANE
(IF ANY)
1568 PF01
1568 PF02
U W
BLOCK DIAGRA
A D TEST CIRCUIT
V+
CBP1
0.1µF
R11
1.27k
INA
V+
R31
1
1.27k INVA
2
16
15
C1A
SA 3
–
–
R21
1.27k
A1A
+
+
+
OUTA
A-SIDE
DIFFERENTIAL
OUTPUTS
–
OUTA
OUTA
R12
1.27k
INB
R22
1.27k
14 SB
A1B
13
4
5
R32
INVB 1.27k
C1B
OUTB
OUTB
–1
–1
12
+
B-SIDE
DIFFERENTIAL
OUTPUTS
C2B
C2A
OUTA
V+
OUTB
OUTB
+
–
V
5k
GNDA
NC
V–
0.1µF
V
GNDB
6
11
5k
7
–
8
V–
10
9
EN
V–
TYPICAL CAPACITOR VALUES:
C1 = 105.7pF ±0.75%
C2 = 141.3pF ±0.75%
1568BD
1568f
9
LT1568
U
W
U U
APPLICATIO S I FOR ATIO
The LT1568 has been designed to make the implementation of high frequency filtering functions very easy. Internal low noise amplifiers and capacitors are configured in
a topology that requires only three external resistors to
implement a 2nd order filter stage. The two 2nd order
stages can be used independently or cascaded for simple
4th order filter functions. With two stages integrated on
the same die, the matching of the independent sections is
better than what can be achieved with separate amplifier
components.
OPERATING WITH SINGLE OR DUAL SUPPLIES
Figure 1 shows the recommended connection of an analog
ground plane with the LT1568 biased from either symmetrical dual (±V) power supplies or a single supply. Connection of the two GND pins is important to properly DC bias
the internal amplifiers. The use of a ground plane helps to
minimize noise and stray components to preserve signal
integrity and maintain frequency response accuracy.
When biasing from a dual supply, it is recommended that
a Schottky diode clamp (BAT54S) be added as shown.
These diodes ensure that improper supply voltages,
through either reverse polarity or power-up sequencing,
do not damage the LT1568.
Dual Supply Power and Ground Connections
ANALOG
GROUND
PLANE
V+
1
2
BAT54S
3
4
5
6
7
V–
8
V+
INVA
SA
V+
INVB
16
15
SIMPLE FILTER IMPLEMENTATIONS
The basic 2nd order filter block of the LT1568, with three
external resistors connected as shown in the Block Diagram, has the following lowpass transfer function:
DCGAIN • (2πfO )
eOUT
=–
2πf
2
eIN
s2 + O s + (2πfO )
Q
2
where eOUT is either OUTA or OUTB,
DCGAIN =
R2
1
, fO =
R1
2π R2 • R3 • C1 • C2
and
Q=
2π • C1 • C2 • R1 • R2 • R3 • fO
C1 • R1 • (R2 + R3) + R2 • R3 – C2 • R1 • R2
[
]
The typical values of the internal capacitors are:
C1= 105.7pF
C2 = 141.3pF
These filter functions assume ideal amplifiers.
Single Supply Power and Ground Connections
ANALOG
GROUND
PLANE
V+
1
2
0.1µF
3
14
SB
LT1568
13
OUTA OUTB
12
OUTA OUTB
11
GNDA GNDB
10
NC
EN
9
V–
V–
4
5
6
0.1µF
7
8
V+
INVA
SA
V+
INVB
16
15
0.1µF
14
SB
LT1568
13
OUTA OUTB
12
OUTA OUTB
11
GNDA GNDB
10
NC
EN
9
V–
V–
0.1µF
SINGLE POINT
SYSTEM GROUND
DIGITAL GROUND PLANE
(IF ANY)
SINGLE POINT
SYSTEM GROUND
1568 F01a
DIGITAL GROUND PLANE
(IF ANY)
1568 F01b
Figure 1. Dual and Single Supply and Ground Plane Connections
1568f
10
LT1568
U
W
U U
APPLICATIO S I FOR ATIO
The following filter examples are provided to make it easy
to design a variety of filter stages. Both 2nd and 4th order
filters are shown. For each filer, a table of external resistor
values (standard 1% tolerance) is provided. These resistor
values have been adjusted to compensate for the finite
gain bandwidth product of the LT1568 amplifiers.
To implement a filter, simply connect the resistor values
shown in the table for the cutoff frequency desired. If the
desired cutoff frequency is not shown in the table of
values, use interpolation as recommended in the next
section.
Example: Implement a 2nd order lowpass Chebyshev filter
with an fC of 256kHz. From Table 2 the values for fC of
1MHz are R11 = R21 = 976Ω and R31 825Ω.
Scaling for fC = 256kHz:
R11 = R21 = 976Ω • (1MHz/256kHz) ≈ 3.83k
R31 = 825Ω • (1MHz/256kHz) ≈ 3.24k
For a Cutoff Frequency, fC, Between Values Given in a
Design Table
DESIGNING FOR ANY CUTOFF FREQUENCY
Start with the resistor values for the cutoff frequency
closest to the desired one and scale the values up or down
accordingly.
To implement a lowpass filter with a cutoff frequency not
included in the design table, resistor values can be interpolated in the following manner:
Example: Implement a 2nd order lowpass Chebyshev filter
with an fC of 3.2MHz. From Table 2 the closest values are
for fC of 3MHz and are R11 = R21 = 316Ω and R31 = 274Ω.
For a Cutoff Frequency, fC, Less Than 1MHz
Start with the resistor values for fC = 1MHz and then scale
them up by the ratio of (1MHz/fC).
Scaling for fC = 3.2MHz:
R11 = R21 = 316Ω • (3MHz/3.2MHz) ≈ 294Ω
R31 = 274Ω • (3MHz/3.2MHz) ≈ 255Ω
1568f
11
LT1568
U
DUAL 2nd ORDER LOWPASS FILTER DESIG S
Dual 2nd Order Lowpass Filter,
Dual Supply Operation
Dual 2nd Order Lowpass Filter,
Single Supply Operation
2.7V ≤ V + ≤ 10V
5V
0.1µF
1
R11
R31
VIN1
2
3
BAT54S
R21
VOUTA
VOUTA
4
5
6
7
8
0.1µF
V+
V+
0.1µF
16
15
INVA
INVB
LT1568
14
SA
SB
13
OUTA
OUTB
12
OUTA
OUTB
11
GNDA
GNDB
10
NC
EN
9
–
–
V
V
R32
R12
R11
VIN2
R31
VIN1
V+
2
15
INVA
INVB
LT1568
14
SA
SB
13
OUTA
OUTB
12
OUTA
OUTB
11
GNDA
GNDB
10
NC
EN
9
–
–
V
V
3
R22
R21
VOUTB
VOUTB
VOUTA
VOUTA
4
5
6
0.1µF 7
R11 = R21 = R31 = R = 128Ω •
fC = fCUTOFF
8
10MHz
fC
16
1
V+
R32
R12
VIN2
R22
VOUTB
VOUTB
1568 TA03
1568 TA04
–5V
Table 1. Resistor Values in Ohms, Dual 2nd Order
Butterworth, Gain = 1, R12 = R11, R22 = R21, R32 = R31
fCUTOFF (MHz)
R11 = R21 = R31
0.2
6340Ω
0.5
2550Ω
1
1270Ω
2
634Ω
3
422Ω
4
324Ω
5
255Ω
6
210Ω
7
182Ω
8
162Ω
9
143Ω
10
127Ω
Amplitude Response
2nd Order Butterworth, fCUTOFF = 1MHz
Transient Response
2nd Order Butterworth, fCUTOFF = 1MHz
10
0
–10
GAIN (dB)
–20
–30
–40
INPUT
500mV/DIV
–50
–60
OUTPUT
200mV/DIV
–70
–80
–90
0.1
1µs/DIV
1
FREQUENCY (MHz)
10
1568 TA08
20
1568 TA07
1568f
12
LT1568
U
DUAL 2nd ORDER LOWPASS FILTER DESIG S
Table 2. Resistor Values in Ohms, Dual 2nd Order Lowpass
Chebyshev, ±0.25dB Passband Ripple, Gain = 1, R11 = R12,
R21 = R22, R31 = R32
fCUTOFF (MHz)
1
2
3
4
5
6
7
R11, R21
976Ω
475Ω
316Ω
226Ω
178Ω
143Ω
121Ω
Amplitude Response 2nd Order Lowpass Chebyshev,
±0.25dB Passband Ripple, fCUTOFF = 1MHz
R31
825Ω
412Ω
274Ω
205Ω
165Ω
137Ω
118Ω
Transient Response 2nd Order Lowpass Chebyshev,
±0.25dB Passband Ripple, fCUTOFF = 1MHz
10
0
–10
GAIN (dB)
–20
–30
–40
INPUT
500mV/DIV
OUTPUT
200mV/DIV
–50
–60
–70
–80
–90
0.1
1
FREQUENCY (MHz)
10
1µs/DIV
20
1568 TA10
1568 TA09
Table 3. Resistor Values in Ohms, Dual 2nd Order Lowpass
Bessel, Gain = 1
fCUTOFF (MHz)
1
2
3
4
5
6
7
Amplitude Response
2nd Order Lowpass Bessel, fCUTOFF = 1MHz
R11, R21
866Ω
422Ω
280Ω
210Ω
165Ω
137Ω
115Ω
R31
1180Ω
590Ω
383Ω
287Ω
232Ω
191Ω
162Ω
Transient Response
2nd Order Lowpass Bessel, fCUTOFF = 1MHz
10
0
–10
GAIN (dB)
–20
–30
–40
INPUT
500mV/DIV
OUTPUT
200mV/DIV
–50
–60
–70
–80
–90
0.1
1
FREQUENCY (MHz)
10
20
1µs/DIV
1568 TA12
1568 TA11
1568f
13
LT1568
U
4th ORDER LOWPASS FILTER DESIG S
4th Order Lowpass Filter,
Dual Supply Operation
4th Order Lowpass Filter,
Single Supply Operation
V+
5V
0.1µF
1
R11
R31
VIN
2
3
R21
BAT54S
4
5
6
7
8
V+
V+
0.1µF
16
R32
15
R11
R12
R31
VIN
INVA
INVB
LT1568
14
SA
SB
13
OUTA
OUTB
12
OUTA
OUTB
11
GNDA
GNDB
10
NC
EN
9
–
–
V
V
V+
2
15
INVA
INVB
LT1568
14
SA
SB
13
OUTA
OUTB
12
OUTA
OUTB
11
GNDA
GNDB
10
NC
EN
9
–
–
V
V
3
R21
R22
4
VOUT
VOUT
16
1
5
6
0.1µF 7
8
V+
R32
R12
R22
VOUT
VOUT
0.1µF
1568 TA05
1568 TA06
–5V
Table 4. Resistor Values in Ohms, 4th Order Lowpass
Butterworth, Gain = 1
fCUTOFF (MHz)
R11, R21
R31
R12, R22
R32
1
1.05k
1.58k
1.82k
887Ω
2
523Ω
787Ω
909Ω
432Ω
3
348Ω
523Ω
590Ω
294Ω
4
255Ω
383Ω
432Ω
215Ω
5
205Ω
309Ω
348Ω
174Ω
6
169Ω
255Ω
280Ω
143Ω
7
143Ω
221Ω
232Ω
124Ω
8
124Ω
196Ω
196Ω
107Ω
9
107Ω
174Ω
169Ω
97.6Ω
10
97.6Ω
158Ω
143Ω
88.7Ω
Amplitude Response
4th Order Lowpass Butterworth Lowpass, fCUTOFF = 1MHz
Transient Response
4th Order Lowpass Butterworth Lowpass, fCUTOFF = 1MHz
12
0
–12
GAIN (dB)
–24
–36
–48
INPUT
500mV/DIV
–60
–72
OUTPUT
200mV/DIV
–84
–96
–108
0.1
1µs/DIV
1
FREQUENCY (MHz)
10
1568 TA14
20
1568 TA13
1568f
14
LT1568
U
4th ORDER LOWPASS FILTER DESIG S
Table 5. Resistor Values in Ohms, 4th Order Lowpass
Chebyshev, ±0.25dB Passband Ripple, Gain = 1
fCUTOFF (MHz)
1
2
3
4
5
6
7
8
9
10
R11, R21
1.87k
931Ω
604Ω
453Ω
357Ω
287Ω
243Ω
205Ω
178Ω
154Ω
R31
2.05k
1.05k
681Ω
511Ω
402Ω
332Ω
287Ω
249Ω
221Ω
196Ω
Amplitude Response 4th Order Lowpass Chebyshev,
±0.25dB Passband Ripple, fCUTOFF = 1MHz
R12, R22
2.21k
1.10k
698Ω
499Ω
383Ω
309Ω
255Ω
215Ω
182Ω
158Ω
R32
634Ω
324Ω
205Ω
154Ω
121Ω
100Ω
86.6Ω
76.8Ω
66.5Ω
61.9Ω
Transient Response 4th Order Lowpass Chebyshev,
±0.25dB Passband Ripple, fCUTOFF = 1MHz
12
0
–12
–24
GAIN (dB)
–36
–48
INPUT
500mV/DIV
–60
–72
OUTPUT
200mV/DIV
–84
–96
–108
0.1
1µs/DIV
1
FREQUENCY (MHz)
10
1568 TA16
20
1568 TA13
Table 6. Resistor Values in Ohms, 4th Order Lowpass Bessel,
Gain = 1
fCUTOFF (MHz)
1
2
3
4
5
6
Amplitude Response
4th Order Lowpass Bessel, fCUTOFF = 1MHz
R11, R21
715Ω
357Ω
237Ω
174Ω
137Ω
115Ω
R31
1.15k
562Ω
374Ω
280Ω
221Ω
187Ω
R12, R22
1.91k
432Ω
280Ω
205Ω
162Ω
130Ω
R32
324Ω
365Ω
243Ω
187Ω
147Ω
124Ω
Transient Response
4th Order Lowpass Bessel, fCUTOFF = 1MHz
12
0
–12
GAIN (dB)
–24
–36
–48
INPUT
500mV/DIV
OUTPUT
200mV/DIV
–60
–72
–84
–96
–108
0.1
1
FREQUENCY (MHz)
10
20
1µs/DIV
1568 TA18
1568 TA17
1568f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LT1568
U
TYPICAL APPLICATIO S
Amplitude Response
4th Order Bandpass Filter fCENTER = 10MHz
4th Order Bandpass Filter
fCENTER = 10MHz, –3dB Passband = fCENTER/5.4
6
5V
PIN 13 OUTPUT
0
0.1µF
1
R11 93.1Ω
VIN
2
3
R21 113Ω
4
5
6
0.1µF
7
8
V
+
V
+ 16
LT1568
15
INVA
INVB
14
SA
SB
13
OUTA
OUTB
12
OUTA
OUTB
11
GNDA GNDB
10
NC
EN
9
V–
V–
R12 93.1Ω
CIN2
39pF
5%
–6
–12
GAIN (dB)
CIN1
39pF
5%
R22 113Ω
VOUT
VOUT
–18
–24
–30
–36
–42
–48
–54
10
FREQUENCY (MHz)
1
40
1568 TA19
1568 TA20
U
PACKAGE DESCRIPTIO
GN Package
16-Lead Plastic SSOP (Narrow .150 Inch)
(Reference LTC DWG # 05-08-1641)
.189 – .196*
(4.801 – 4.978)
.015 ± .004
× 45°
(0.38 ± 0.10)
.007 – .0098
(0.178 – 0.249)
.053 – .068
(1.351 – 1.727)
16 15 14 13 12 11 10 9
.004 – .0098
(0.102 – 0.249)
.009
(0.229)
REF
.045 ±.005
0° – 8° TYP
.016 – .050
(0.406 – 1.270)
.0250
(0.635)
BSC
.008 – .012
(0.203 – 0.305)
NOTE:
1. CONTROLLING DIMENSION: INCHES
INCHES
2. DIMENSIONS ARE IN
(MILLIMETERS)
.229 – .244
(5.817 – 6.198)
.150 – .157**
.254 MIN
(3.810 – 3.988)
.150 – .165
GN16 (SSOP) 0502
3. DRAWING NOT TO SCALE
*DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE
**DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE
1
2 3
4
5 6
7
8
.0165 ± .0015
.0250 TYP
RECOMMENDED SOLDER PAD LAYOUT
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC 1563
4th Order Filter Building Block
Lowpass or Bandpass Filter Designs, 256Hz to 256kHz
LTC1565-31
7th Order, Fully Differential 650kHz Lowpass Filter
SO-8, No External Components
LTC1566-1
7th Order, Fully Differential 2.3MHz Lowpass Filter
SO-8, No External Components
LT1567
Very Low Noise Op Amp and Inverter
1.4nV/√Hz Op Amp, MSOP Package, Differential Outputs
LT6600-10
Fully Differential 10MHz Lowpass Filter
55µVRMS Noise 100kHz to 10MHz, Operates with 3V Supply
LT6600-20
Fully Differential 20MHz Lowpass Filter
86µVRMS Noise 100kHz to 20MHz, Operates with Single 3V Supply
®
1568f
16
Linear Technology Corporation
LT/TP 0403 2K • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
 LINEAR TECHNOLOGY CORPORATION 2003