HER601 THRU HER608 6.0 AMP HIGH EFFICIENCY RECTIFIERS VOLTAGE RANGE 50 TO 1000 Volts CURRENT 6.0 Amperes FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * High speed switching R-6 .360(9.1) .340(8.6) DIA. 0.945(24.0) MIN. MECHANICAL DATA * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Axial leads, solderable per MIL-STD-202, method 208 guranteed * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 1.65 grams * Both normal and Pb free product are available: * Normal:80~95%Sn,5~20%Pb * Pb free:99 Sn above can meet Rohs enviroment substance directive request .360(9.1) .340(8.6) 0.945(24.0) MIN. .052(1.3) .043(1.1) DIA. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current HER601 HER602 HER603 HER604 HER605 HER606 HER607 HER608 50 100 200 300 400 600 800 1000 35 50 70 100 140 200 210 300 280 400 420 600 560 800 700 1000 .375"(9.5mm) Lead Length at Ta=50 C Peak Forward Surge Current, 8.3 ms single half sine-wave 300 1.3 10.0 1.0 at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG 1.70 200 50 75 -55 NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 72 100 +150 V V V A 6.0 superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 6.0A Maximum DC Reverse Current Ta=25 C UNITS A V µA µA nS pF C RATING AND CHARACTERISTIC CURVES (HER601 THRU HER608) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE CHARACTERISTICS -H HE R6 06 R6 HE AVERAGE FORWARD CURRENT,(A) 08 ER 6 -6 04 R6 01 05 -6 03 10.0 HE 1.0 6 Single Phase Half Wave 60Hz Resistive Or Inductive Load 5 Ground Plane 4 1" X 1" Copper surface area 3 PC BOARD Recommended 2 PC BOARD PC Board Mounting Standard PC Board 1 Mounting 0 20 40 Tj=25 C 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE ( C) Pulse Width 300us 1% Duty Cycle .1 .01 .2 .4 .6 .8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50Ω NONINDUCTIVE 10Ω NONINDUCTIVE ( ) (+) D.U.T. 25Vdc (approx.) PULSE GENERATOR (NOTE 2) ( ) 1Ω NONINDUCTIVE OSCILLISCOPE (NOTE 1) PEAK FORWAARD SURGE CURRENT,(A) FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 500 400 300 Sine Wave 200 JEDEC method 100 0 1 | | | | | | | | 0 -0.25A 1cm 100 175 150 125 100 75 50 25 0 -1.0A 50 10 FIG.5-TYPICAL JUNCTION CAPACITANCE 2. Rise Time= 10ns max., Source Impedance= 50 ohms. +0.5A 5 NUMBER OF CYCLES AT 60Hz NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. trr 8.3ms Single Half Tj=25 C (+) JUNCTION CAPACITANCE,(pF) INSTANTANEOUS FORWARD CURRENT,(A) 100 0.1 SET TIME BASE FOR 0.5 1 2 5 10 20 REVERSE VOLTAGE,(V) 50 / 10ns / cm 73 50 100 200 500 1000