Ordering number : ENA1112A LB11852FV Monolithic Digital IC For Fan Motor http://onsemi.com Single-phase Full-wave Pre-driver with Speed Control Function Overview The LB11852FV is a single-phase bipolar driving motor pre-driver with a speed control function based on speed feedback. With a small number of external parts, a highly efficient and very quiet variable-speed drive fan motor with low power consumption and high rotational accuracy can be implemented. The LB11852FV, integrated in a miniature package, is best suited for driving small fan motors requiring speed control. Features • Single-phase full-wave driving pre-driver ⇒ With a PMOS-NMOS device used as the external power transistor, low saturation output and a single-phase full-wave drive enable a high-efficiency drive with low power consumption. • Speed control circuit incorporated ⇒ Compared with open-loop control, a closed-loop control function that uses speed feedback to control the speed makes it possible to improve the rotational speed accuracy and reduce the variations in the rotational speed caused by fluctuations in the supply voltage or load. The separately excited upper direct PWM method is featured as the variable speed system. • Variable speed control is possible with external PWM input or analog voltage input ⇒ The speed control input signal is compatible with PWM duty ratio and analog voltages. • Soft start circuit incorporated • Minimum speed setting pin ⇒ The minimum speed can be set using an external resistor. • Current limiting circuit incorporated ⇒ Chopper type current limit at startup or lock. • Reactive current cut circuit incorporated ⇒ Reactive current before phase changeover is cut, ensuring highly silent and low power-consumption drive. • Automatic resetting type constraint circuit incorporated • FG (rotational speed detection) output ORDERING INFORMATION See detailed ordering and shipping information on page 12 of this data sheet. Semiconductor Components Industries, LLC, 2013 September, 2013 91113NK 20130828-S00001/40208 MS PC 20080225-S00005 No.A1112-1/12 LB11852FV Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit VCC pin maximum supply voltage VCC max 18 V OUTN pin maximum output current IOUTN max 20 mA OUTP pin maximum Sink current IOUTP max 20 mA OUT pin output withstand voltage VOUT max 18 V CTL, C pin withstand voltage CTL, C max 7 V LIM pin withstand voltage LIM max 7 V FG output pin output withstand voltage FG max 19 V FG output current FG max 10 mA 10 mA 5VREG pin maximum output current Allowable power dissipation I5VREG max Pd max Mounted on a specified board *1 0.8 W Operating temperature Topr -30 to 95 °C Storage temperature Tstg -55 to 150 °C *1 Mounted on a specified board : 114.3mm×76.1mm×1.6mm, glass epoxy *2 Tj max = 150°C. Use the device in a condition that the chip temperature does not exceed Tj = 150°C during operation. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Recommended Operating Conditions at Ta = 25°C Parameter Symbol Conditions Ratings Unit VCC supply voltage 1 VCC1 VCC pin VCC supply voltage 2 VCC2 VCC -5VREG 4.5 to 5.5 V CTL input voltage range VCTL 0 to 5VREG V LIM input voltage range VLIM 0 to 5VREG V Hall input common phase input VICM 0.2 to 3 V 5.5 to 16 V voltage range Electrical Characteristics at Ta = 25°C, VCC = 12V, unless otherwise specified Parameter Circuit current 5VREG voltage Symbol Conditions Ratings min typ Unit max ICC1 During drive 12 15 mA ICC2 During lock protection 12 15 mA 4.8 5.0 5.2 V mV 5VREG I5VREG = 5mA Current limiting voltage VLIM 190 210 230 CPWM pin H level voltage VCRH 2.8 3.0 3.2 V CPWM pin L level voltage VCRL 0.9 1.1 1.3 V CPWM pin charge current ICPWM1 VCPWM = 0.5V 24 30 36 μA CPWM pin discharge current ICPWM2 VCPWM = 3.5V 21 27 33 CPWM oscillation frequency FPWM CT pin H level voltage VCTH CT pin L level voltage VCTL CT pin charge current ICT1 VCT = 2V CT pin discharge current ICT2 CT pin charge/discharge current ratio C = 220pF 30 μA kHz 2.8 3.0 3.2 V 0.9 1.1 1.3 V 1.6 2.0 2.5 μA VCT = 2V 0.16 0.20 0.25 μA 8 RCT ICT1/ICT2 10 12 OUTN pin output H voltage VONH IO = 10mA VCC-0.85 VCC-1.0 times V OUTN pin output L voltage VONL IO = 10mA 0.9 1.0 V OUTP pin output L voltage VOPL IO = 10mA 0.5 0.65 V Hall input sensitivity VHN IN+, IN- differential voltage ±15 ±25 mV (including offset and hysteresis) Continued on next page. No.A1112-2/12 LB11852FV Continued from preceding page. Parameter Symbol FG output L voltage VFGL IFG = 5mA FG pin leak current IFGL VFG = 19V EO pin output H voltage Ratings Conditions VEOH IEO1 = -0.2mA EO pin output L voltage VEOL IEO1 = 0.2mA RC pin output H voltage RC pin output L voltage min typ Unit max 0.15 0.30 V 30 μA VREG-1.2 VREG-0.8 0.8 1.1 VRCH 3.2 3.45 3.7 V VRCL 0.7 0.8 1.05 V VRCCLP 1.3 1.5 1.7 V CTL pin input H voltage VCTLH 2.0 VREG V CTL pin input L voltage VCTLL 0 1.0 V CTL pin input open voltage VCTLO VREG-0.5 VREG V CTL pin H input H current ICTLH VFGIN = 5VREG 10 μA CTL pin L input L current ICTLL VFGIN = 0V RC pin clamp voltage C pin output H voltage C pin output L voltage V V -10 0 -120 -90 μA VCH VREG-0.3 VREG-0.1 V 2.0 VCL 1.8 2.2 V LIM pin input bias current IBLIM -1 1 μA LIM pin common phase input voltage VILIM 2.0 VREG V 1.6 μA VREG V range SOFT pin charge current ICSOFT 1.0 SOFT pin operating voltage range VISOFT 2.0 1.3 Package Dimensions unit : mm (typ) 3360 12 0.22 0.15 1.5 MAX 0.1 (1.3) (0.35) Allowable power dissipation, Pd max – W 0.5 4.4 6.4 20 0.5 Pd max -- Ta 1.0 5.2 0.8 When mounted on the thermal resistance evaluation board 0.80 0.6 0.4 Independent IC 0.35 0.30 0.2 0.13 0 – 30 0 30 60 90 120 Ambient temperature, Ta – °C SSOP20J(225mil) No.A1112-3/12 LB11852FV Truth table Lock protection CPWM = H IN- IN+ H L L H H L L H CT L H OUT1P OUT1N OUT2P OUT2N FG Mode L L OFF H L OUT1 → 2 drive OFF H L L OFF OUT2 → 1 drive OFF L OFF H L OFF H OFF L OFF Lock protection Speed control CT = L EO L H CPWM H L IN- IN+ OUT1P OUT1N OUT2P OUT2N Mode H L L L OFF H OUT1 → 2 drive OUT2 → 1 drive L H OFF H L L H L OFF L OFF H L H OFF H OFF L Regeneration mode Pin Assignment OUT2P 1 20 OUT1P OUT2N 2 19 OUT1N VCC 3 SENCE 4 C 5 CTL 6 RC 7 18 SGND 17 5VREG 16 EO 15 EI 14 LIM SOFT 8 13 CT CPWM 9 12 IN+ FG 10 11 IN- Top view No.A1112-4/12 VCC CTL signal CTL C SOFT LIM RC 5VREG VCC CTL VREF 1shot multi VREG EI EDEG Thermal shat down FG EO F G 5VREG IN+ HALL CT IN- CPW M Oscillation CONTROL CIRCUIT Discharge circuit SENSE 5VREG GND OUT2 P OUT2 N OUT1 P OUT1 N LB11852FV Block Diagram No.A1112-5/12 LB11852FV Sample Application Circuit *3 1μF/25V Rp = 1kΩ 1 3 2 100Ω 4 RF 1μF/25V RFG = 10kΩ to 100kΩ *2 VCC *8 5VREG SENSE RC LIM SOFT OUT1P 1 OUT1N 2 OUT2P 3 OUT2N 4 H IN+ CTL CT EL EO 5VREG *4 IN- C CTLsignal *7 SGND *1 *5 CP = 1μF *6 CP = 220pF 30kHz CPWM No.A1112-6/12 LB11852FV Description of Pre-driver Bock *1 : Power-GND wiring The SGND is connected to the control circuit power supply system. *2 : Power stabilization capacitor For the power stabilization capacitor on the signal side, use a capacitor of 0.1μF or more. Connect the capacitor between VCC and GND with a thick and along the shortest possible route. *3 : Power-side power stabilization capacitor For the power-side power stabilization capacitor, use a capacitor of 1μF or more. Connect the capacitor between the power-side power supply and GND with a thick and along the shortest possible route. *4 : IN+, IN- pins Hall signal input pins Wiring should be short to prevent noise from being carried. If noise is carried, insert a capacitor between the IN+ and IN- pins. The Hall input circuit functions as a comparator with hysteresis (15mV). It also has a soft switch zone with ±30mV (input signal difference voltage). It is also recommended that the Hall input level should be a minimum of 100mV (p-p). *5 : CPWM pin Pin to connect the capacitor used to generate the PWM basic frequency Use of CP = 200pF causes oscillation at f = 30kHz, which is the basic frequency of PWM. As this is also used for the current limiter reset signal, a capacitor must be connected even if the speed is not going to be controlled. *6 : CT pin Pin to connect the capacitor used for lock detection The constant-current charging and constant-current discharging circuits incorporated cause locking when the pin voltage reaches 3.0V, and releasing the lock protection when it drops to 1.0V. Connect this pin to the GND when it is not to be used (locking not necessary). *7 : SENSE pin Current limiter detection pin When the pin voltage exceeds 0.21V, the current limiter is activated, and operation enters lower regeneration mode. Connect this pin to the GND when it is not to be used. *8 : FG pin Rotational speed detection pin This is an open collector output that can detect the rotational speed using the FG output corresponding to the phase changeover. Keep this pin open when it is not to be used. No.A1112-7/12 LB11852FV Description of Speed Control Block 1. Speed control diagram The slope is determined by the RC pin constant. (RPM) CR time constant large CR time constant small Rotational speed Minimum speed Determined by LIM pin voltage 0% Minimum speed setting rotation Small ← CTL signal (PWMDUTY) → Large Large ← EO pin voltage (V) → Small Variable speed On-duty small 100% Full speed On-duty large CTL pin 5VREG LIM voltage EO pin EO voltage 0V 2. Timing at startup (soft start) VCC pin CTL pin Stop Full speed Soft start The slope changes depending on the capacitance of the SOFT pin (large capacitance large slope). SOFT pin Stop Full speed No.A1112-8/12 LB11852FV 2. Supplementary description of operations By inputting the duty pulses, a feedback loop is formed inside the LB11852 IC to establish the FG period (rotational speed of the motor) that corresponds to the control voltage of the pulses. LB11852 FG CTL Signal CTL Speed control block Closed Pre-driver block Feed-Back Loop CONTROL SIGNAL The operation inside the IC is as flows. pulse signals are created from the edges of the FG signals as shown in the figure below, and using these signals as a reference, waveforms with a pulse width determined by the CR time constant are generated using a one-shot multivibrator. These pulse waveforms are then integrated to control the duty ratio of the pre-driver output as the control voltage. FG Edge pulse Slope determined by CR time constant RC pin One-shot multivibrator output TRC (sec) = 1.15RC By changing the pulse width as determined by the CR time constant, the VCTL versus rotational speed slope can be adjusted as shown in the speed control diagram in the previous section. However, since pulses that are determined by the CR time constant are used, the CR variations are output as-is as the speed control error. No.A1112-9/12 LB11852FV 4. Procedure for calculating the constant 〈RC pin〉 The slope shown in the speed control diagram is determined by the constant of the RC pin. (RPM) Motor at maximum speed 0% CTL Duty(%) 100% 1) Obtain the FG signal frequency fFG (Hz) at the maximum rotational speed of the motor (with two FG pulses per rotation). fFG (Hz) = 2 rpm/60 … (1) 2) Obtain the time constant of the components connected to the RC pin (use the duty ratio (example : 100% = 1.0 or 60% = 0.6) as the CTL duty ratio for achieving the maximum rotational speed). R × C = Duty ratio/ (3.3 × 1.1 × fFG) … (2) 3) Obtain the resistance and the capacitance of the capacitor. Based on the discharge capability of the RC pin, the capacitance of the capacitor which can be used is in the range of 0.01μF to 0.015μF. Therefore, obtain the appropriate resistance from the result of (2) above using the formula in (3) or (4) below. R = (R × C)/0.01μF … (3) R = (R × C)/0.015μF … (4) The temperature characteristics of the curve are determined by the temperature characteristics of the capacitor of the RC pin. To minimize the variations in the rotational speed caused by temperature, a capacitor with excellent temperature characteristics must be used. No.A1112-10/12 LB11852FV 〈LIM pin〉 The minimum speed is determined by the voltage of the LIM pin. (RPM) Maximum speed 10000 8000 6000 4000 Minimum speed setup 2000 0% 5V CTL Duty(%) CVO pin voltage (V) 100% 2V 1) Obtain the ratio of the minimum speed required to the maximum speed. Ra = Minimum/maximum speed … (1) In the example shown in the figure above : Ra = minimum/maximum speed = 3000/10000 = 0.3 2) Obtain the product of the duty ratio at which the maximum speed is achieved and the value in formula (1). Ca = Maximum speed duty ratio × Ra … (2) In the example given : Ca = maximum speed duty ratio × Ra = 0.8 × 0.3 = 0.24 3) Obtain the required LIM pin voltage. LIM = 5 - (3 × Ca) … (3) In the example given : LIM = 5 - (3 × Ca) = 5 - (3 × 0.24) ≈ 4.3V 4) Divide the resistance of 5VREG to generate the LIM voltage. In the example given, the voltage is 4.3V so the resistance ratio is 1 : 6. The resistance is 10kΩ between 5VREG and LIM and 62kΩ between LIM and GND. 5VREG LIM VREF SOFT No.A1112-11/12 LB11852FV 〈C pin〉 In order to connect a capacitor capable of smoothing the pin voltage to the C pin, the correlation given in the following equation must be satisfied when f (Hz) serves as the input frequency of the CTL pin. (R is incorporated inside the IC, and it is 180kΩ (typ.).) 1/f = t < CR The higher the capacitance of the capacitor, the slower the response to changes in the input signals. 5VREF A capacitor capable of the smoothing pin voltage is connected here 1/f = t < CR Inverted waveform of CTL pin input (same frequency) C pin CTL pin CTL circuit VREF circuit 180kΩ ORDERING INFORMATION Device LB11852FV-TLM-H Package SSOP20J (225mil) (Pb-Free / Halogen Free) Shipping (Qty / Packing) LB11852FV-TLM-E SSOP20J (225mil) (Pb-Free / Halogen Free) 2000 / Tape & Reel LB11852FV-MPB-E SSOP20J (225mil) (Pb-Free / Halogen Free) 90 / Fan-Fold LB11852FV-MPB-H SSOP20J (225mil) (Pb-Free / Halogen Free) 90 / Fan-Fold 2000 / Tape & Reel ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A1112-12/12