Holtek HT45FH23A Smoke detector flash mcu with power line transceiver Datasheet

Smoke Detector Flash MCU with Power Line Transceiver
HT45FH23A/HT45FH24A
Revision: V1.00
Date: �����������������
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Table of Contents
Features.................................................................................................................. 7
MCU CPU Features....................................................................................................................... 7
MCU Peripheral Features.............................................................................................................. 8
Two Line Power Line Data Transceiver Features.......................................................................... 8
General Description............................................................................................... 9
Selection Table..................................................................................................... 10
Block Diagram...................................................................................................... 10
Pin Assignment.....................................................................................................11
Pin Description.....................................................................................................11
Unbonded MCU Pins................................................................................................................... 13
Internally Connected Pins............................................................................................................ 14
Absolute Maximum Ratings................................................................................ 14
D.C. Characteristics............................................................................................. 15
A.C. Characteristics............................................................................................. 17
OP Amplifier Electrical Characteristics............................................................. 18
Comparator Electrical Characteristics.............................................................. 18
LDO 2.4V............................................................................................................... 19
LDO 3.3V............................................................................................................... 19
Two Line Type Power Line Data Transceiver Characteristics ........................ 19
Power-on Reset Characteristics......................................................................... 20
System Architecture............................................................................................ 21
Clocking and Pipelining................................................................................................................ 21
Program Counter.......................................................................................................................... 22
Stack............................................................................................................................................ 23
Arithmetic and Logic Unit – ALU.................................................................................................. 23
Flash Program Memory....................................................................................... 24
Structure....................................................................................................................................... 24
Special Vectors............................................................................................................................ 24
Look-up Table............................................................................................................................... 25
Table Program Example............................................................................................................... 26
In Circuit Programming................................................................................................................ 27
RAM Data Memory............................................................................................... 28
Structure....................................................................................................................................... 29
Special Function Registers................................................................................. 29
Indirect Addressing Registers – IAR0, IAR1................................................................................ 30
Memory Pointers – MP0, MP1..................................................................................................... 30
Bank Pointer – BP........................................................................................................................ 31
Accumulator – ACC...................................................................................................................... 31
Program Counter Low Register – PCL......................................................................................... 32
Rev. 1.00
2
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Look-up Table Registers – TBLP, TBHP, TBLH............................................................................ 32
Status Register – STATUS........................................................................................................... 32
EEPROM Data Memory........................................................................................ 34
EEPROM Data Memory Structure............................................................................................... 34
EEPROM Registers..................................................................................................................... 34
Reading Data from the EEPROM................................................................................................ 36
Writing Data to the EEPROM....................................................................................................... 36
Write Protection............................................................................................................................ 36
EEPROM Interrupt....................................................................................................................... 36
Programming Considerations....................................................................................................... 37
Programming Examples............................................................................................................... 37
Oscillators............................................................................................................ 38
Oscillator Overview...................................................................................................................... 38
System Clock Configurations....................................................................................................... 38
External Crystal/Ceramic Oscillator – HXT.................................................................................. 39
External Oscillator – EC............................................................................................................... 40
Internal RC Oscillator – HIRC...................................................................................................... 40
External 32.768kHz Crystal Oscillator – LXT............................................................................... 40
LXT Oscillator Low Power Function............................................................................................. 41
Internal 32kHz Oscillator – LIRC.................................................................................................. 42
Supplementary Oscillators........................................................................................................... 42
Operating Modes and System Clocks............................................................... 42
System Clocks............................................................................................................................. 42
System Operation Modes............................................................................................................. 43
Control Register........................................................................................................................... 45
Fast Wake-up............................................................................................................................... 46
Operating Mode Switching........................................................................................................... 47
Standby Current Considerations.................................................................................................. 52
Wake-up....................................................................................................................................... 53
Programming Considerations....................................................................................................... 53
Watchdog Timer................................................................................................... 54
Watchdog Timer Clock Source..................................................................................................... 54
Watchdog Timer Control Register................................................................................................ 54
Watchdog Timer Operation.......................................................................................................... 55
Reset and Initialisation........................................................................................ 56
Reset Functions........................................................................................................................... 56
Reset Initial Conditions................................................................................................................ 59
Input/Output Ports............................................................................................... 62
Pull-high Resistors....................................................................................................................... 62
Port A Wake-up............................................................................................................................ 62
I/O Port Control Registers............................................................................................................ 62
I/O Pin Structures......................................................................................................................... 64
Programming Considerations....................................................................................................... 64
Rev. 1.00
3
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Timer/Event Counters......................................................................................... 66
Configuring the Timer/Event Counter Input Clock Source........................................................... 66
Timer Registers – TMR0, TMR1L, TMR1H.................................................................................. 66
Timer Control Registers – TMR0C, TMR1C................................................................................. 68
Configuring the Timer Mode......................................................................................................... 68
Configuring the Event Counter Mode........................................................................................... 69
Configuring the Pulse Width Measurement Mode........................................................................ 69
Programmable Frequency Divider – PFD.................................................................................... 71
Prescaler...................................................................................................................................... 71
I/O Interfacing............................................................................................................................... 74
Timer/Event Counter Pins Internal Filter...................................................................................... 74
Programming Considerations....................................................................................................... 74
Timer Program Example.............................................................................................................. 75
Pulse Width Modulator........................................................................................ 76
PWM Operation............................................................................................................................ 76
6+2 PWM Mode........................................................................................................................... 77
7+1 PWM Mode........................................................................................................................... 78
PWM Output Control.................................................................................................................... 79
Analog to Digital Converter................................................................................ 80
A/D Overview............................................................................................................................... 80
A/D Converter Register Description............................................................................................. 81
A/D Converter Data Registers – ADRL, ADRH............................................................................ 81
A/D Converter Control Registers – ADCR, ACSR, ADPCR......................................................... 81
A/D Operation.............................................................................................................................. 85
A/D Input Pins.............................................................................................................................. 86
Summary of A/D Conversion Steps.............................................................................................. 87
Programming Considerations....................................................................................................... 88
A/D Transfer Function.................................................................................................................. 88
A/D Programming Example.......................................................................................................... 89
Serial Interface Module – SIM............................................................................. 91
SPI Interface................................................................................................................................ 91
I2C Interface................................................................................................................................. 98
Peripheral Clock Output.................................................................................... 106
Peripheral Clock Operation........................................................................................................ 106
SCOM Function for LCD.................................................................................... 107
LCD Operation........................................................................................................................... 107
LCD Bias Control....................................................................................................................... 107
LDO Function............................................................................................................................. 109
Operational Amplifiers.......................................................................................111
Operational Amplifier Registers...................................................................................................111
Operational Amplifier Operation..................................................................................................113
Operational Amplifier Functions..................................................................................................114
Rev. 1.00
4
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Comparators.......................................................................................................118
Comparator Operation................................................................................................................118
Comparator Registers.................................................................................................................118
Comparator Functions................................................................................................................ 120
Interrupts............................................................................................................ 123
Interrupt Register....................................................................................................................... 123
Interrupt Operation..................................................................................................................... 123
Interrupt Priority.......................................................................................................................... 124
External Interrupt........................................................................................................................ 127
External Peripheral Interrupt...................................................................................................... 129
Timer/Event Counter Interrupt.................................................................................................... 129
SIM Interface Interrupt............................................................................................................... 130
Multi-function Interrupt............................................................................................................... 130
A/D Interrupt............................................................................................................................... 130
Time Base Interrupt.................................................................................................................... 131
Comparator Interrupt.................................................................................................................. 132
EEPROM Interrupt..................................................................................................................... 132
LVD Interrupt.............................................................................................................................. 132
Interrupt Wake-up Function........................................................................................................ 132
Programming Considerations..................................................................................................... 133
Buzzer................................................................................................................. 133
Low Voltage Detector – LVD............................................................................. 135
LVD Register.............................................................................................................................. 135
LVD Operation............................................................................................................................ 136
Voice Output....................................................................................................... 137
Voice Control.............................................................................................................................. 137
Audio Output and Volume Control – DAL, DAH, DACTRL ........................................................ 137
Power Line Data Transceiver ........................................................................... 138
Shared Power Line..................................................................................................................... 139
Data Transmission (From master controller to slave device)..................................................... 139
Data Reception (From slave device to master controller).......................................................... 140
Current Modulator ..................................................................................................................... 140
Application Considerations......................................................................................................... 140
Power Line Data Transceiver Application Circuits...................................................................... 141
Configuration Options....................................................................................... 142
Application Circuits........................................................................................... 143
Instruction Set.................................................................................................... 144
Introduction................................................................................................................................ 144
Instruction Timing....................................................................................................................... 144
Moving and Transferring Data.................................................................................................... 144
Arithmetic Operations................................................................................................................. 144
Logical and Rotate Operation.................................................................................................... 145
Branches and Control Transfer.................................................................................................. 145
Rev. 1.00
5
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit Operations............................................................................................................................ 145
Table Read Operations.............................................................................................................. 145
Other Operations........................................................................................................................ 145
Instruction Set Summary.................................................................................. 146
Table Conventions...................................................................................................................... 146
Instruction Definition......................................................................................... 148
Package Information......................................................................................... 157
20-pin SOP (300mil) Outline Dimensions.................................................................................. 158
Rev. 1.00
6
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Features
MCU CPU Features
• Operating voltage
♦♦
fSYS= 32.768kHz: 2.2V~5.5V
♦♦
fSYS= 910kHz: 2.2V~5.5V
♦♦
fSYS= 2MHz: 2.2V~5.5V
♦♦
fSYS= 4MHz: 2.2V~5.5V
♦♦
fSYS= 8MHz: 3.3V~5.5V
• TinyPowerTM technology for low power operation
• Power down and wake-up functions to reduce power consumption
• Oscillator types
♦♦
External Crystal – HXT
♦♦
External 32.768kHz Crystal – LXT
♦♦
Internal RC – HIRC
♦♦
Internal 32kHz RC – LIRC
♦♦
External Clock – EC
• Multi-mode operation: NORMAL, SLOW, IDLE and SLEEP
• Fully integrated internal 910kHz, 2MHz, 4MHz and 8MHz oscillator require no external
components
• All instructions executed in one or two machine cycles
• Table read instructions
• 61 or 63 powerful instructions
• 6-level subroutine nesting
• Bit manipulation instruction
Rev. 1.00
7
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
MCU Peripheral Features
• Flash Program Memory: 2K×15 ~ 4K×16
• RAM Data Memory: 128×8 ~ 192×8
• True EEPROM Data Memory: 64×8
• Up to 13 bidirectional I/O lines
• Watchdog Timer function
• Single pin-shared external interrupt
• Software controlled 4-SCOM lines LCD COM driver with 1/2 bias
• Single 8-bit programmable Timer/Event Counter with overflow interrupt function
• Single 16-bit programmable Timer/Event Counter with overflow interrupt function
• Dual Time-Base functions for generation of fixed time interrupt signals
• Serial Interfaces Module – SPI or I2C
• Dual Comparators
• Dual Operational Amplifiers
• Operational Amplifier output to internal two channel 12-bit ADC
• 3-channel 12-bit ADC
• 2-channel 8-bit PWM
• 12-bit Audio DAC output
• PFD/Buzzer for audio frequency generation
• Internal 2.4V/3.3V LDO
• Low voltage reset function
• Low voltage detect function
• Package types: 20-pin SOP
• Flash program memory can be re-programmed up to 100,000 times
• Flash program memory data retention > 10 years
• True EEPROM data memory can be re-programmed up to 1,000,000 times
• True EEPROM data memory data retention > 10 years
Two Line Power Line Data Transceiver Features
• Complete Data Transmission on Power Line functions
• High Maximum Input Voltage: 42V
• Integrated Low Dropout Voltage Regulator
• Integrated Voltage Detector for Power Supply Monitoring
• Integrated Comparator
• Open drain NMOS driver for flexible interfacing
• Power and Reset Protection Features
• Minimal external component requirements
Rev. 1.00
8
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
General Description
These devices are Flash Memory TinyPowerTM A/D type 8-bit high performance RISC architecture
microcontrollers. Offering users the convenience of Flash Memory multi-programming features, the
devices also include wide range of functions and features. Other memory includes an area of RAM
Data Memory as well as an area of true EEPROM memory for storage of non-volatile data such as
serial numbers, calibration data etc.
Analog features include an integrated multi-channel Analog to Digital Converter, dual Operational
Amplifiers, dual Comparators, an internal 2.4V or 3.3V low dropout voltage regulator and a 12-bit
DAC for voice output applications Communication with the outside world is catered for with a fully
integrated SPI or I2C interface, two popular interfaces which provide designers with a means of easy
communication with external peripheral hardware. Two Pulse Width Modulators are also included.
Protective features such as an internal Watchdog Timer, Low Voltage Reset and Low Voltage
Detector coupled with excellent noise immunity and ESD protection ensure that reliable operation is
maintained in hostile electrical environments.
This series of devices also contain a two line type power line data transceiver. In systems where
a master controller controls a number of individual interconnected subsystems such as found in
smoke detector systems, water metering systems, solar energy system, etc., the cost of the lengthy
interconnecting cabling can be a major factor. By sending data along the power supply lines, the
interconnecting cables can be reduced to a simple two line type, thus greatly reducing both cable and
installation costs. With the addition of a few external components, this power line data transceiver
device contains all the internal components required to provide users with a system for power line
data transmission and reception. Data is modulated onto the power line by the simple reduction of
the power line voltage for a specific period of time. Power supply voltage changes can be initiated
by the master controller for data reception or initiated by the power line data transceiver for data
transmission. An internal voltage regulator with a Soft-start and short circuit protection functions
ensures that a constant voltage power supply is provided to the interconnected subsystem units while
an internal voltage detector monitors the power line voltage level. An internal comparator is used to
translate the differential signal into a logic signal for the MCU.
A full choice of internal, external, low and high speed oscillator functions are provided including
fully integrated system oscillators which require no external components for their implementation.
The unique Holtek TinyPower TM technology also gives the devices extremely low current
consumption characteristics, an extremely important consideration in the present trend for low
power battery powered applications. The usual Holtek MCU features such as power down and
wake-up functions, oscillator options, programmable frequency divider, etc. combine to ensure user
applications require a minimum of external components. The inclusion of flexible I/O programming
features, Time-Base functions along with many other features ensure that the devices will find
excellent use in applications such as networked smoke detectors, electronic metering, environmental
monitoring, handheld instruments, household appliances, electronically controlled tools, motor
driving, home security systems and many others.
Rev. 1.00
9
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Selection Table
Part No.
Program
Memory
Data
Memory
Data
EEPROM
I/O
External
Interrupt
A/D
Timer
Modules
HT45FH23A
2K×15
128×8
64×8
13
1
12-bit×3
8-bit×1
16-bit×1
HT45FH24A
4K×16
192×8
64×8
13
1
12-bit×3
8-bit×1
16-bit×1
Part No.
Time Base
SIM
Comp.
Op. Amp.
Data
Transceiver
Stack
Package
HT45FH23A
2
√
√
√
√
6
20SOP
HT45FH24A
2
√
√
√
√
6
20SOP
Block Diagram
The following block diagram illustrates the dual-chip structure of the devices, where an individual
MCU and a two-line type power line data transceiver chips are combined into a single package.
VCC
VIN
VDD
IO Ports
OPA pins
(3.3V)
OSC pins
PB0
RX
TRX
PB5
TX
IS
VSS
VSS
VSS
VSS
EEPROM
Data
Me�o�y
Flash
P�og�a�
Me�o�y
Low
Voltage
Detect
RAM Data
Me�o�y
CN
TRX
IS
Inte�nal
HIRC/LIRC
Oscillato�s
Watchdog
Ti�e�
Flash/EEPROM
P�og�a��ing Ci�cuit�y
VDD (3.3V)
CN
Power Line
Data
Transceiver
HT45F23A
HT45F24A
A/D pins
VO
VO
Inte��upt
Cont�olle�
8-�it
RISC
MCU
Co�e
Low
Voltage
Reset
Exte�nal
HXT/LXT
Oscillato�s
Reset
Ci�cuit
Ti�e
Base
LDO
1�-�it A/D
Conve�te�
D/A
Conve�te�
PWM
Gene�ato�
Rev. 1.00
PFD/
Buzze�
D�ive�
LCD
D�ive�
Ti�e�s
SIM
(SPI/I�C)
I/O
Co�pa�ato� /
Op. A�p.
Powe� Line
Data T�ansceive�
10
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Pin Assignment
PA1/C1OUT/TC0
1
20
VDD
PA0/CNP/SCOM0
PC3/XT2
2
19
VSS
3
18
PA2/A1P/C2OUT
PC2/XT1
PC1/AN5/OSC1
4
17
PA3/A1N/INT0
5
16
PA4/A1E/TC1
PC0/AN4/OSC2
6
15
PA5/A2P/PFD
PB6/AN3/RES
7
14
PA6/A2N/BZ
VSS
TRX
8
9
13
12
PA7/A2E/BZ
CN
10
11
IS
VCC
HT45FH23A/HT45FH24A
20 SOP-A
Note: 1. The HT45FH23A I/O lines, PB0/SDO/INT1, PB5/AN2/PINT and VDD are internally
connected to the two line type power line data inputs, TX and VO respectively. PB0~PB5,
PC4~PC6 and their pin-shared function pins are not connected to external pins.
2. The HT45FH24A I/O lines, PB0/SDO/INT1, PB5/AN2/PINT and VDD are internally
connected to the two line type power line data transceiver inputs, TX and VO respectively.
PB0~PB5, PB7, PC4~PC7, PD0~PD1 and their pin-shared function pins are not connected
to the external pins.
3. Pin 8 and pin 19 must be connected together in the application PCB.
4. As the INT1 and AN0~AN2 pins for the HT45FH23A and the INT1, AN0~AN2 and
AN6~AN7 pins for the HT45FH24A are not connected to their external pin assignments,
only one external interrupt and three external A/D channels are available for use
Pin Description
With the exception of the power pins and some relevant power line data transceiver pins, all pins on
these devices can be referenced by their Port name, e.g. PA0, PA1 etc, which refer to the digital I/O
function of the pins. However these Port pins are also shared with other function such as the Analog
to Digital Converter, Timer Module pins etc. The function of each pin is listed in the following table,
however the details behind how each pin is configured is contained in other sections of the datasheet.
Pad Name
PA0/CNP/
SCOM0
PA1/C1OUT/
TC0
PA2/A1P/
C2OUT
PA3/A1N/INT0
Function
OPT
I/T
PA0
PAPU
PAWU
ST
CNP
Description
CMOS General purpose I/O. Register enabled pull-up and wake-up
—
Comparator input
SCOM0
LCDC
—
SCOM Software controlled 1/2 bias LCD COM
PA1
PAPU
PAWU
ST
CMOS General purpose I/O. Register enabled pull-up and wake-up
C1OUT
CMP1C1
—
CMPO Comparator 1 output
TC0
—
ST
PA2
PAPU
PAWU
ST
A1P
OPA1C1 OPAI
—
Timer 0 external clock input
CMOS General purpose I/O. Register enabled pull-up and wake-up
—
Operational amplifier 1 non-inverting input
C2OUT
CMP2C1
—
CMPO Comparator 2 output
PA3
PAPU
PAWU
ST
CMOS General purpose I/O. Register enabled pull-up and wake-up
A1N
INT0
Rev. 1.00
CMP1C1 CMPI
O/T
OPA1C1 OPAI
—
ST
—
Operational amplifier 1 inverting input
—
External Interrupt 0 input
11
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Pad Name
PA4/A1E/TC1
PA5/A2P/PFD
PA6/A2N/BZ
PA7/A2E/BZ
PB6/AN3/RES
PC0/AN4/OSC2
PC1/AN5/OSC1
PC2/XT1
PC3/XT2
Function
OPT
I/T
PA4
PAPU
PAWU
ST
CMOS General purpose I/O. Register enabled pull-up and wake-up
A1E
OPA1C1
—
OPAO Operational amplifier 1 output
TC1
—
ST
PA5
PAPU
PAWU
ST
A2P
OPA2C1 OPAI
O/T
—
Description
Timer 1 external clock input
CMOS General purpose I/O. Register enabled pull-up and wake-up
—
Operational amplifier 2 non-inverting input
PFD
MISC
—
CMOS PFD output
PA6
PAPU
PAWU
ST
CMOS General purpose I/O. Register enabled pull-up and wake-up
A2N
OPA2C1 OPAI
—
Operational amplifier 2 inverting input
BZ
BPCTL
—
CMOS Buzzer output
PA7
PAPU
PAWU
ST
CMOS General purpose I/O. Register enabled pull-up and wake-up
A2E
OPA2C1
—
OPAO Operational amplifier 2 output
BZ
BPCTL
—
CMOS Complementary buzzer output
PB6
PBPU
ST
CMOS General purpose I/O. Register enabled pull-up.
AN3
ADCR
AN
—
A/D Converter analog input
RES
CO
ST
—
External reset pin
PC0
PCPU
ST
CMOS General purpose I/O. Register enabled pull-up.
AN4
ADCR
AN
—
OSC2
CO
—
HXT
PC1
PCPU
ST
A/D Converter analog input
HXT oscillator pin
CMOS General purpose I/O. Register enabled pull-up.
AN5
ADCR
AN
—
A/D Converter analog input
OSC1
CO
HXT
—
HXT oscillator pin
PC2
PCPU
ST
XT1
CO
LXT
PC3
PCPU
ST
CMOS General purpose I/O. Register enabled pull-up.
—
LXT oscillator pin
CMOS General purpose I/O. Register enabled pull-up.
XT2
CO
—
LXT
CN
CN
—
AN
—
IS
IS
—
—
TRX
—
—
—
Transceiver signal detect/modulate
VSS
VSS
—
PWR
—
Power line data transceiver negative power supply, ground.
VCC
VCC
—
PWR
—
Power line data transceiver LDO Input
VDD
VDD
—
PWR
—
Power line data transceiver LDO output, MCU positive
power supply
VSS
VSS
—
PWR
—
Negative power supply, ground.
TRX
LXT oscillator pin
Comparator negative input
NMOS Source terminal of constant current NMOS driver
Legend: I/T: Input type;
O/T: Output type
OPT: Optional by configuration option (CO) or register option
PWR: Power;
CO: Configuration option
ST: Schmitt Trigger input;
AN: Analog input
CMPI: Comparator input;
OPAI: Operational Amplifier input
CMOS: CMOS output;NMOS: NMOS output
CMPO: Comparator output;
OPAO: Operational Amplifier output
SCOM: Software controlled LCD COM
HXT: High frequency crystal oscillator pins
LXT: Low frequency crystal oscillator pins
Note: The VSS pin should be externally connected to the VSS pin for normal operation.
Rev. 1.00
12
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Unbonded MCU Pins
Examination of the relevant MCU datasheet will reveal that not all of the MCU I/O port lines are
bonded out to external pins. As a result special attention regarding initialisation procedures should
be paid to these port lines. Users should ensure that these pins are setup in input states with pull high
resistors or in output states with either a high or low levels to avoid additional power consumption
resulting from floating input pins.
Pin Name
Function
OPT
I/T
PB0
PBPU
MISC
ST
General purpose I/O. Register enabled pull-up and output
CMOS NMOS structure.
NMOS Internally connected to the Power Line Data Transceiver
line, RX.
SDO
—
—
CMOS SPI data output
INT1
—
ST
PB1
PBPU
MISC
ST
PB0/SDO/INT1
PB1/SDI/SDA
PB2/SCK/SCL
PB3/AN0/SCS
PB4/AN1/AUD/
PCK
PB5/AN2/PINT
PB7*
PC4/VREF/
VCAP/SCOM1
PC5/PWM0/
C1N/SCOM2
PC6/PWM1/
C2P/SCOM3
PC7*
PD0/AN6*
Rev. 1.00
O/T
—
Description
External interrupt 1 input pin
CMOS General purpose I/O. Register enabled pull-up and output
NMOS NMOS structure.
SDI
—
ST
SDA
—
ST
NMOS I2C data
—
PB2
PBPU
MISC
ST
CMOS General purpose I/O. Register enabled pull-up and output
NMOS NMOS structure.
SCK
—
ST
SCL
—
ST
NMOS I2C clock
PB3
PBPU
MISC
ST
CMOS General purpose I/O. Register enabled pull-up and output
NMOS NMOS structure.
AN0
ADCR
AN
—
A/D channel 0
SCS
—
ST
—
SPI slave select
—
SPI data input
SPI serial clock
PB4
PBPU
ST
CMOS General purpose I/O. Register enabled pull-up
AN1
ADCR
AN
CMOS A/D channel 1
AUD
DACTRL
—
PCK
—
—
CMOS Peripheral clock output
PB5
PBPU
ST
General purpose I/O. Register enabled pull-up
CMOS Internally connected to the Power Line Data Transceiver
line, TX.
DAO
D/A output pin
AN2
ADCR
AN
—
A/D channel 2
PINT
—
ST
—
Peripheral interrupt
PB7
PBPU
ST
CMOS General purpose I/O. Register enabled pull-up
PC4
PCPU
ST
CMOS General purpose I/O. Register enabled pull-up.
VREF
ACSR
AN
—
ADC reference input
VCAP
LDOC
—
—
LDO output capacitor pin. Connect a 0.1µF capacitor.
SCOM1
LCDC
—
SCOM Software controlled 1/2 bias LCD COM
PC5
PCPU
ST
CMOS General purpose I/O. Register enabled pull-up.
PWM0
BPCTL
—
CMOS PWM0 output pin
C1N
CMP1C1 CMPI
—
Comparator 1 inverting input pin
SCOM2
LCDC
—
SCOM Software controlled 1/2 bias LCD COM
PC6
PCPU
ST
CMOS General purpose I/O. Register enabled pull-up.
BPCTL
—
CMOS PWM1 output pin
PWM1
C2P
CMP2C1 CMPI
—
Comparator 2 non-inverting input pin
SCOM3
LCDC
—
SCOM Software controlled 1/2 bias LCD COM
PC7
PCPU
ST
CMOS General purpose I/O. Register enabled pull-up.
PD0
PDPU
ST
CMOS General purpose I/O. Register enabled pull-up.
AN6
ADCR
AN
—
A/D channel 6
13
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Pin Name
PD1/AN7*
Function
OPT
I/T
PD1
PDPU
ST
AN7
ADCR
AN
O/T
Description
CMOS General purpose I/O. Register enabled pull-up.
—
A/D channel 7
Legend: I/T: Input type;
O/T: Output type
OPT: Optional by configuration option (CO) or register option
ST: Schmitt Trigger input;
AN: Analog input;
DAO: D/A output
CMPI: Comparator input;
CMOS: CMOS output
NMOS: NMOS output
SCOM: Software controlled LCD COM
*: PB7, PC7, PD0/AN6 and PD1/AN7 are only existed in the HT45FH24A.
Internally Connected Pins
Among the pins mentioned in the tables above several pins are not connected to external package
pins. These pins are interconnection pins between the MCU and the power line data transceiver chip
and are listed in the following table. The description is provided from the power line data transceiver
chip standpoint.
Power Line Data
Transceiver Pin Name
Type
RX
O
Comparator output, transmitter signal detect output
Internally connected to the MCU I/O line, PB0.
TX
I
Input pin for constant current modulate
Internally connected to the MCU I/O line, PB5.
VO
PWR
LDO output
Connected to MCU positive power supply, VDD
Description
Absolute Maximum Ratings
Supply Voltage.................................................................................................VSS−0.3V to VSS+6.0V
Input Voltage...................................................................................................VSS−0.3V to VDD+0.3V
Storage Temperature.....................................................................................................-50˚C to 125˚C
Operating Temperature...................................................................................................-40˚C to 85˚C
IOL Total.................................................................................................................................... 100mA
IOH Total...................................................................................................................................-100mA
Total Power Dissipation.......................................................................................................... 500mW
Note: These are stress ratings only. Stresses exceeding the range specified under "Absolute Maximum
Ratings" may cause substantial damage to these devices. Functional operation of these devices at
other conditions beyond those listed in the specification is not implied and prolonged exposure to
extreme conditions may affect devices reliability.
Rev. 1.00
14
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
D.C. Characteristics
Ta=25˚C
Symbol
VDD
Parameter
Test Conditions
Min.
Typ.
Max.
Unit
fSYS=910kHz, (HXT/HIRC)
2.2
—
5.5
V
fSYS=2MHz, (HXT/HIRC)
2.2
—
5.5
V
fSYS=4MHz,
(HXT/HIRC/EC)
2.2
—
5.5
V
fSYS=8MHz
(HXT/HIRC/EC)
3.3
—
5.5
V
No load, fSYS=fM=455kHz,
ADC off, LVR off,
Comparator off, OPAs off
—
70
110
µA
Operating Current (HXT)
No load, fSYS=fM= 455kHz,
ADC off, LVR on,
Comparator on, OPAs off
—
100
150
µA
Operating Current (HIRC)
No load, fM=910kHz,
fSYS=fSLOW=455kHz,
ADC off, LVR off,
Comparator off, OPAs off
—
90
135
µA
Operating Current (HIRC)
No load, fM=910kHz,
fSYS=fSLOW=455kHz,
ADC off, LVR on,
Comparator on, OPAs off
—
120
180
µA
Operating Current (HIRC)
No load, fSYS=fM=910kHz,
ADC off, LVR off,
Comparator off, OPAs off
—
110
170
µA
Operating Current (HIRC)
No load, fSYS=fM=910kHz,
ADC off, LVR on,
Comparator on, OPAs off
—
160
240
µA
Operating Current (HXT)
No load, fSYS=fM=1MHz,
ADC off, LVR off,
Comparator off, OPAs off
—
120
180
µA
Operating Current (HXT)
No load, fSYS=fM=1MHz,
ADC off, LVR on,
Comparator on, OPAs off
—
170
260
µA
Operating Current (HXT, HIRC)
No load, fSYS=fM=2MHz,
ADC off, LVR off,
Comparator off, OPAs off
—
170
260
µA
No load, fSYS=fM=2MHz,
ADC off, LVR on,
Comparator on, OPAs off
—
200
300
µA
No load, fSYS=fM=4MHz,
ADC off
—
420
630
µA
—
700
1000
µA
No load, fSYS=fM=4MHz,
ADC off
—
330
500
µA
—
550
820
µA
—
1.5
3.0
mA
No load, fSYS=fSLOW=1MHz,
ADC off
—
200
300
µA
—
400
600
µA
No load, fSYS=fSLOW=2MHz,
ADC off
—
250
375
µA
—
560
840
µA
No load, fSYS=fSLOW=2MHz,
ADC off
—
300
450
µA
—
680
1020
µA
Operating Voltage
VDD
—
Operating Current (HXT)
IDD1
3.3V
IDD2
3.3V
IDD3
3.3V
IDD4
3.3V
IDD5
3.3V
Operating Current (HXT, HIRC)
IDD6
IDD7
Operating Current (HXT, HIRC)
Operating Current (EC)
3V
5V
3V
5V
IDD8
Operating Current (HXT, HIRC)
5V
IDD9
Operating Current (Slow Mode,
fM=4MHz) (HXT, HIRC)
3V
IDD10
Operating Current (Slow Mode,
fM=4MHz) (HXT, HIRC)
3V
IDD11
Operating Current (Slow Mode,
fM=8MHz) (HXT, HIRC)
3V
Rev. 1.00
5V
5V
5V
Conditions
No load, fSYS=fM=8MHz,
ADC off
15
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Symbol
Parameter
Test Conditions
VDD
Conditions
No load, fSYS=fSLOW=4MHz,
ADC off
IDD12
Operating Current (Slow Mode,
fM=8MHz) (HXT, HIRC)
3V
IDD13
Operating Current
(fSYS=LXT note 1 or LIRC)
3V
ISTB1
Standby Current (Sleep)
(fSYS, fSUB, fS, fWDT=off)
3V
ISTB2
Standby Current (Sleep)
(fSYS Off; fS On;
fWDT=fSUB=LXT note 1 or LIRC)
3V
ISTB3
Standby Current (Idle)
(fSYS Off; fWDT Off; fS=fSUB=LXTnote 1 or LIRC)
3V
ISTB4
Standby Current (Idle)
(fSYS On, fSYS=fM=4MHz; fWDT Off;
fS=fSUB=LXT note 1 or LIRC)
3V
VIL1
Input Low Voltage for I/O, TCn and INTn
—
VIH1
Input High Voltage for I/O, TCn and INTn
—
VIL2
Input Low Voltage (RES)
VIH2
Min.
Typ.
Max.
Unit
—
450
800
µA
—
1000
1500
µA
—
10
20
µA
—
20
35
µA
—
0.1
1.0
µA
—
0.2
2.0
µA
—
1.5
3.0
µA
—
2.5
5.0
µA
No load, system HALT,
WDT off
—
4
6
µA
—
6
9
µA
No load, system HALT,
WDT off, SPI or I2C on,
PCK on, fPCK=fSYS/8
—
260
350
µA
—
350
660
µA
—
0
—
0.3VDD
V
—
0.7VDD
—
VDD
V
—
—
0
—
0.4VDD
V
Input High Voltage (RES)
—
—
0.9VDD
—
VDD
V
VIL3
Input Low Voltage (PB1~PB3)
5V
—
—
—
1
V
VIH3
Input High Voltage (PB1~PB3)
5V
—
2
—
—
V
+5%
V
+5%
V
5V
5V
5V
5V
5V
5V
VLVR1
VLVR2
VLVR3
No load, WDT off, ADC off
No load, system HALT,
WDT off
No load, system HALT,
WDT on
VLVR=2.10V
Low Voltage Reset
—
2.10
VLVR=2.55V
-5%
VLVR=3.15V
2.55
3.15
VLVR4
VLVR=4.20V
4.20
VLVD1
LVDEN=1, VLVD=2.0V
2.0
VLVD2
LVDEN=1, VLVD=2.2V
2.2
VLVD3
LVDEN=1, VLVD=2.4V
2.4
VLVD4
LVDEN=1, VLVD=2.7V
VLVD5
Low Voltage Detector Voltage
—
LVDEN=1, VLVD=3.0V
-5%
2.7
3.0
VLVD6
LVDEN=1, VLVD=3.3V
3.3
VLVD7
LVDEN=1, VLVD=3.6V
3.6
VLVD8
LVDEN=1, VLVD=4.4V
IOL
I/O Port Sink Current
IOH
I/O Port Source Current
RPH
Pull-high Resistance
AVDD
3V
5V
3V
5V
VOL=0.1VDD
VOH=0.9VDD
4.4
6
12
—
mA
10
25
—
mA
-2
-4
—
mA
-5
-8
—
mA
3V
—
40
60
80
kΩ
5V
—
10
30
50
kΩ
A/D Converter Operating Voltage
—
—
2.7
—
5.5
V
VAD
A/D Input Voltage
—
—
0
—
VREF
V
VREF
A/D Input Reference Voltage Range
—
AVDD=5V
2
—
VDD
V
VREF=VDD, tAD=1µs
—
±1
±2
LSB
VREF=VDD, tAD=1µs
—
±2
±4
LSB
DNL
ADC Differential Non-Linearity
INL
ADC Integral Non-Linearity
IADC
Additional Power Consumption
if A/D Converter is Used
Rev. 1.00
3V
5V
3V
5V
3V
—
—
0.5
1.0
mA
5V
—
—
1.5
3.0
mA
16
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Symbol
Test Conditions
Parameter
VDD
Conditions
—
—
Min.
Typ.
Max.
Unit
-3%
1.25
+3%
V
—
10
15
µA
—
20
30
µA
VBG
Bandgap Reference with Buffer
voltage
ILVR
DC current when LVR or LVD
turn on
3V
VDD/2 Voltage for LCD COM
5V
No load
0.475 0.500 0.525
VDD
VLDO/2 Voltage for LCD COM
5V
No load
0.475 0.500 0.525
VLDO
VSCOM
IOUT
—
5V
Output Current
5V
ISEL=0, LCDBUF=0
—
10
—
ISEL=1, LCDBUF=0
—
25
—
µA
µA
ISEL=0, LCDBUF=1
—
2
—
mA
ISEL=1, LCDBUF=1
—
2
—
mA
Note: 1. tSYS= 1/fSYS; tSUB = 1/fSUB
2. Detailed showing please refer LDO section.
A.C. Characteristics
Ta=25˚C
Symbol
fSYS1
fSYS2
fSYS3
fSYS4
fSYS5
Parameter
System Clock (HXT, HIRC)
8MHz HIRC
4MHz HIRC
2MHz HIRC
910kHz HIRC
Test Conditions
Min.
Typ.
Max.
Unit
2.2V~5.5V
400
—
4000
kHz
3.3V~5.5V
400
—
8000
kHz
3.3V
Ta=25˚C
-2%
8
+2%
MHz
3.3V
Ta=-40~85˚C
-5%
8
+5%
MHz
2.7V~5.5V Ta=-40~85˚C
VDD
—
Conditions
-10%
8
+10%
MHz
3.3V
Ta=25˚C
-2%
4
+2%
MHz
3.3V
Ta=-40~85˚C
-5%
4
+5%
MHz
2.7V~5.5V Ta=-40~85˚C
-10%
4
+10%
MHz
3.3V
Ta=25˚C
-2%
2
+2%
MHz
3.3V
Ta=-40~85˚C
-5%
2
+5%
MHz
2.7V~5.5V Ta=-40~85˚C
-10%
2
+10%
MHz
-2%
0.91
+2%
MHz
3.3V
Ta=25˚C
3.3V
Ta=-40~85˚C
-5%
0.91
+5%
MHz
2.7V~5.5V Ta=-40~85˚C
-10%
0.91
+10%
MHz
fLXT
System Clock (LXT)
—
—
—
32.768
—
kHz
tLIRC
32kHz RC Period
3V
—
28.10
31.25
34.40
µs
tRES
External Reset Low Pulse Width
—
—
1
—
—
µs
tLVR
Low Voltage width to Reset
—
—
60
120
240
µs
tLVD
Low Voltage width to Interrupt
—
—
60
120
240
µs
tLVDS
LVDO Stable Time
5V
—
—
100
µs
tRSTD
System Reset Delay Time
—
—
—
100
—
ms
tSST1
System start-up timer period
(W/O fast start-up) of HXT/TBC
—
Power up or wake-up from
Sleep mode
—
1024
—
tSYS* note 1
tSST2
System start-up timer period of
HIRC, EC
—
Power up or wake-up from
HALT (Idle or Sleep mode)
—
1
2
tSYS
tSST3
System start-up timer period
(With fast start-up) of HXT/TBC
—
wake-up from Idle mode
(fSL=fTBC)
—
1
2
tTBC note 2
tSST4
System start-up timer period
(With fast start-up) of HXT/TBC
—
wake-up from Idle mode
(fSL=fLIRC)
—
1
2
tLIRC
Rev. 1.00
LVR disable, LVD enable,
VBG is ready
17
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Symbol
Parameter
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
Unit
µs
tINT
Interrupt Pulse Width
—
—
1
—
—
tAD
A/D Clock Period
—
—
0.5
—
—
µs
tADC
A/D Conversion Time Note 4
—
—
—
16
—
tAD
tON2ST
A/D on to A/D Start
—
2
—
—
µs
2.2V~5.5V
Note: 1. tSYS=1/fSYS; tSUB=1/fSUB
2. tTBC is period of LXT or LIRC and it will not stop at Idle mode.
3. ADC conversion time (tAD)=n (bits ADC) + 4 (sampling time). The conversion for each bit needs one
ADC clock (tAD).
OP Amplifier Electrical Characteristics
Ta=25˚C
Symbol
Parameter
Test Conditions
VDD
Conditions
Min. Typ.
Max.
Unit
D.C. Characteristic
VDD
Operating voltage
—
—
2.2
—
5.5
V
IDD
Quiescent current
5V
No load, A1OEN/A2OEN fixed to 0
—
200
350
µA
VOPOS
Input offset voltage
5V
—
-5
—
+5
mV
IOPOS
Input offset current
—
VDD=5V, VCM=1/2VDD, Ta=-40~85˚C
—
10
—
nA
VCM
Common Mode Voltage Range
—
—
VSS
—
VDD-1.4
V
PSRR
Power Supply Rejection Ratio
—
—
58
80
—
dB
CMRR
Common Mode Rejection Ratio
—
58
80
—
dB
VDD=5V, VCM=0~VDD-1.4V
A.C. Characteristic
AOL
Open Loop Gain
—
60
80
—
dB
SR
Slew Rate+, Rate
—
No load
—
—
0.1
—
V/µs
GBW
Gain Band Width
—
RL=1MΩ, CL=100pF
1
2
—
MHz
Comparator Electrical Characteristics
Ta=25˚C
Symbol
Parameter
Test Conditions
VDD
Conditions
—
—
Min.
Typ.
Max.
Unit
2.2
—
5.5
V
—
20
40
µA
—
30
60
µA
-10
—
+10
mV
mV
VDDC
Comparator Operating Voltage
IDDC
Comparator Operating Current
VCPOS1
Comparator Input Offset Voltage
5V
CxOF[4:0]=10000
VCPOS2
Comparator Input Offset Voltage
5V
By calibration
-4
—
+4
VCM
Comparator Common Mode Voltage Range
—
—
VSS
—
VDD-1.4
V
AOL
Comparator Open Loop Gain
—
—
60
80
—
dB
tPD1
Comparator Response Time
—
With 2mV overdrive
—
—
2
µs
tPD2
Comparator Response Time
—
With 10mV overdrive
—
—
1.5
µs
Rev. 1.00
3V
5V
18
—
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
LDO 2.4V
Ta=25˚C
Symbol
Parameter
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
Unit
V
VDDIN
Supply Voltage
—
—
2.7
—
5.5
VDDOUT
Output Voltage
—
—
2.28
2.40
2.52
V
IDD
Current Consumption
—
After startup, no load
—
50
70
µA
IOUT
Output Current
5V
VCAP=1µF
200
—
1100
µA
LDO 3.3V
Ta=25˚C
Symbol
Parameter
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
Unit
V
VDDIN
Supply Voltage
—
—
3.6
—
5.5
VDDOUT
Output Voltage
—
—
3.13
3.30
3.46
V
IDD
Current Consumption
—
After startup, no load
—
50
70
µA
IOUT
Output Current
5V
VCAP=1µF
200
—
1100
µA
Note: 1.This LDO can provide stable power supply for PIR sensor with a 10µF cap.
2. The VREF pin should be connected to 10µF for ADC reference voltage and 10µF for PIR sensor.
Two Line Type Power Line Data Transceiver Characteristics
Ta = 25°C
Symbol
Parameter
Test Conditions
VDD
Conditions
Typ.
Max.
Unit
VCC
Operating Voltage
—
7
—
42
V
ICC
Operating Current
—
VCC=42V, VDD no Load,
—
20
40
μA
IOFF
Offline Current
—
VCC=42V, VDD no Load,
TRX=0V
—
10
20
μA
VOFF
TRX Offline Voltage
—
—
—
—
0.5
V
VON
TRX Online Voltage
—
—
4
—
—
V
VT
Threshold Voltage
—
—
—
VMARK-5.6
—
V
IMC
Modulate Current
VIL
Input low voltage for TX pin
3.3V
VIH
Input high voltage for TX pin
3.3V
IOL
Sink current for RX pin
3.3V VOL=0.1VDD
IOH
Source current for RX pin
3.3V VOH=0.9VDD
RPH
Pull-high Resistance for TX
Rev. 1.00
—
Min.
—
RS=100Ω
—
15
—
mA
—
RS=47Ω
—
32
—
mA
—
0
—
0.2VDD
V
—
0.8VDD
—
VDD
V
4
8
—
mA
—
—
19
-2
-4
—
mA
-30%
50
30%
kΩ
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Symbol
Parameter
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
Unit
LDO
VOUT
Output Voltage
3.3V VCC=7V, ILOAD=10mA
3.2
3.3
3.4
V
VCC=10V, ΔVOUT=-3%
60
—
—
mA
VCC=7V, ΔVOUT=-3%
30
—
—
mA
7V ≤ VIN ≤ 42V, ILOAD=1mA
—
—
0.2
%/V
3.3V
Ta=-40˚C ~ 85˚C,
VCC=7V, ILOAD=10mA
—
±0.5
±1
mV/˚C
—
VCC=7V, ILOAD=10mA
—
—
40
mV
VCC=7V, ILOAD=1mA,
3.3V
VOUT=3.3V ± 3%
—
—
10
ms
0.8
—
—
mA
IOUT
Output Current
—
ΔVLINE
Line Regulation
—
TC
Temperature Coefficient
ΔVOUT_RIPPLE Output Voltage Ripple
tSTART
LDO Startup Time
IOL
Sink current for VDD
—
VLVD
Low voltage detection
voltage
—
—
5.7
6.0
6.3
V
VHYS
Hysteresis Voltage
—
—
—
0.5
—
V
TC
Temperature coefficient
(ΔVLVD/ΔTa)
—
—
±0.9
—
mV/˚C
AOL
Open loop gain
—
—
60
80
—
dB
VHYS
Hysteresis
—
—
—
0.15
—
V
tRP
Response time
—
—
—
—
5
μs
—
—
—
—
5
μs
VCC=5V, VOL=0.5V
LVD
Ta=-40˚C ~ 85˚C
Comparator
Constant Current Modulator
tRP
Response Time
Power-on Reset Characteristics
Ta=25˚C
Symbol
Test Conditions
Parameter
VDD
Conditions
Min.
Typ. Max. Unit
VPOR
VDD Start Voltage to Ensure Power-on Reset
—
—
—
—
100
mV
RRVDD
VDD raising rate to Ensure Power-on Reset
—
—
0.035
—
—
V/ms
tPOR
Minimum Time for VDD Stays at VPOR to Ensure
Power-on Reset
—
—
1
—
—
ms
Rev. 1.00
20
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
System Architecture
A key factor in the high-performance features of the Holtek range of microcontrollers is attributed to
the internal system architecture. The devices take advantage of the usual features found within RISC
microcontrollers providing increased speed of operation and enhanced performance. The pipelining
scheme is implemented in such a way that instruction fetching and instruction execution are
overlapped, hence instructions are effectively executed in one cycle, with the exception of branch
or call instructions. An 8-bit wide ALU is used in practically all operations of the instruction set. It
carries out arithmetic operations, logic operations, rotation, increment, decrement, branch decisions,
etc. The internal data path is simplified by moving data through the Accumulator and the ALU.
Certain internal registers are implemented in the Data Memory and can be directly or indirectly
addressed. The simple addressing methods of these registers along with additional architectural
features ensure that a minimum of external components is required to provide a functional I/O and
A/D control system with maximum reliability and flexibility. This makes the devices suitable for
low-cost, high-volume production for controller applications.
Clocking and Pipelining
The main system clock, derived from either a Crystal/ Resonator or RC oscillator is subdivided into
four internally generated non-overlapping clocks, T1~T4. The Program Counter is incremented at
the beginning of the T1 clock during which time a new instruction is fetched. The remaining T2~T4
clocks carry out the decoding and execution functions. In this way, one T1~T4 clock cycle forms
one instruction cycle. Although the fetching and execution of instructions takes place in consecutive
instruction cycles, the pipelining structure of the microcontroller ensures that instructions are
effectively executed in one instruction cycle. The exception to this are instructions where the
contents of the Program Counter are changed, such as subroutine calls or jumps, in which case the
instruction will take one more instruction cycle to execute.


 
 
  
System Clocking and Pipelining
Rev. 1.00
21
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
For instructions involving branches, such as jump or call instructions, two instruction cycles are
required to complete instruction execution. An extra cycle is required as the program takes one
cycle to first obtain the actual jump or call address and then another cycle to actually execute the
branch. The requirement for this extra cycle should be taken into account by programmers in timing
sensitive applications.
     
  
Instruction Fetching
Program Counter
During program execution, the Program Counter is used to keep track of the address of the
next instruction to be executed. It is automatically incremented by one each time an instruction
is executed except for instructions, such as “JMP” or “CALL” that demand a jump to a nonconsecutive Program Memory address. Note that the Program Counter width varies with the
Program Memory capacity depending upon which device is selected. However, it must be noted that
only the lower 8 bits, known as the Program Counter Low Register, are directly addressable by the
application program.
When executing instructions requiring jumps to non-consecutive addresses such as a jump
instruction, a subroutine call, interrupt or reset, etc., the microcontroller manages program control
by loading the required address into the Program Counter. For conditional skip instructions, once
the condition has been met, the next instruction, which has already been fetched during the present
instruction execution, is discarded and a dummy cycle takes its place while the correct instruction is
obtained.
Program Counter
Device
Program Counter High Byte
PCL Register
HT45FH23A
PC10~PC8
PCL7~PCL0
HT45FH24A
PC11~PC8
PCL7~PCL0
The lower byte of the Program Counter, known as the Program Counter Low register or PCL, is
available for program control and is a readable and writeable register. By transferring data directly
into this register, a short program jump can be executed directly. However, as only this low byte
is available for manipulation, the jumps are limited to the present page of memory that is 256
locations. When such program jumps are executed, it should also be noted that a dummy cycle will
be inserted.
The lower byte of the Program Counter is fully accessible under program control. Manipulating the
PCL might cause program branching, so an extra cycle is needed to pre-fetch. Further information
on the PCL register can be found in the Special Function Register section.
Rev. 1.00
22
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Stack
This is a special part of the memory which is used to save the contents of the Program Counter
only. The stack is organized into 6 levels and is neither part of the Data or Program Memory space,
and is neither readable nor writeable. The activated level is indexed by the Stack Pointer, SP, and is
neither readable nor writeable. At a subroutine call or interrupt acknowledge signal, the contents of
the Program Counter are pushed onto the stack. At the end of a subroutine or an interrupt routine,
signaled by a return instruction, RET or RETI, the Program Counter is restored to its previous value
from the stack. After a device reset, the Stack Pointer will point to the top of the stack.
If the stack is full and an enabled interrupt takes place, the interrupt request flag will be recorded but
the acknowledge signal will be inhibited. When the Stack Pointer is decremented, by RET or RETI,
the interrupt will be serviced. This feature prevents stack overflow allowing the programmer to use
the structure more easily. However, when the stack is full, a CALL subroutine instruction can still
be executed which will result in a stack overflow. Precautions should be taken to avoid such cases
which might cause unpredictable program branching.
P ro g ra m
T o p o f S ta c k
S ta c k L e v e l 1
S ta c k L e v e l 2
S ta c k
P o in te r
B o tto m
C o u n te r
S ta c k L e v e l 3
o f S ta c k
P ro g ra m
M e m o ry
S ta c k L e v e l 6
Arithmetic and Logic Unit – ALU
The arithmetic-logic unit or ALU is a critical area of the microcontroller that carries out arithmetic
and logic operations of the instruction set. Connected to the main microcontroller data bus, the ALU
receives related instruction codes and performs the required arithmetic or logical operations after
which the result will be placed in the specified register. As these ALU calculation or operations may
result in carry, borrow or other status changes, the status register will be correspondingly updated to
reflect these changes. The ALU supports the following functions:
• Arithmetic operations: ADD, ADDM, ADC, ADCM, SUB, SUBM, SBC, SBCM, DAA
• Logic operations: AND, OR, XOR, ANDM, ORM, XORM, CPL, CPLA
• Rotation RRA, RR, RRCA, RRC, RLA, RL, RLCA, RLC
• Increment and Decrement INCA, INC, DECA, DEC
• Branch decision, JMP, SZ, SZA, SNZ, SIZ, SDZ, SIZA, SDZA, CALL, RET, RETI
Rev. 1.00
23
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Flash Program Memory
The Program Memory is the location where the user code or program is stored. For the devices
the Program Memory is Flash type, which means it can be programmed and re-programmed
a large number of times, allowing the user the convenience of code modification on the same
device. By using the appropriate programming tools, this Flash devices offer users the flexibility to
conveniently debug and develop their applications while also offering a means of field programming
and updating.
Structure
The Program Memory has a capacity of 2K×15~4K×16 . The Program Memory is addressed by the
Program Counter and also contains data, table information and interrupt entries. Table data, which
can be setup in any location within the Program Memory, is addressed by separate table pointer
registers.
Special Vectors
Within the Program Memory, certain locations are reserved for special usage such as reset and
interrupts.
Location 000H
This vector is reserved for use by the devices reset for program initialisation. After a device reset is
initiated, the program will jump to this location and begin execution.
Location 004H
This vector is used by the external interrupt 0. If the external interrupt pin receives an active edge,
the program will jump to this location and begin execution if the external interrupt is enabled and
the stack is not full.
Location 008H
This vector is used by the external interrupt 1. If the external interrupt pin receives an active edge,
the program will jump to this location and begin execution if the external interrupt is enabled and
the stack is not full.
Location 00CH
This internal vector is used by the Timer/Event Counter 0. If a Timer/Event Counter 0 overflow
occurs, the program will jump to this location and begin execution if the timer/event counter
interrupt is enabled and the stack is not full.
Location 010H
This internal vector is used by the Timer/Event Counter 1. If a Timer/Event Counter 1 overflow
occurs, the program will jump to this location and begin execution if the timer/event counter
interrupt is enabled and the stack is not full.
Location 014H
This internal vector is used by the SIM interrupt. When either an SPI or I2C bus, dependent upon
which one is selected, requires data transfer, the program will jump to this location and begin
execution if the SIM interrupt is enabled and the stack is not full.
Rev. 1.00
24
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Location 018H
This internal vector is used by the Multi-function Interrupt. When the Time Base overflows, the A/D
converter completes its conversion process, an active edge appears on the External Peripheral
interrupt pin, a Comparator output interrupt, an EEPROM Write or Read cycle ends interrupt, or a
LVD detection interrupt, the program will jump to this location and begin execution if the relevant
interrupt is enabled and the stack is not full.
    
       
  Program Memory Structure
Look-up Table
Any location within the Program Memory can be defined as a look-up table where programmers can
store fixed data. To use the look-up table, the table pointer must first be setup by placing the address
of the look up data to be retrieved in the table pointer register, TBLP and TBHP. These registers
define the total address of the look-up table.
After setting up the table pointer, the table data can be retrieved from the Program Memory
using the “TABRDC [m]” or “TABRDL [m]” instructions, respectively. When the instruction is
executed, the lower order table byte from the Program Memory will be transferred to the user
defined Data Memory register [m] as specified in the instruction. The higher order table data byte
from the Program Memory will be transferred to the TBLH special register. Any unused bits in
this transferred higher order byte will be read as “0”. The accompanying diagram illustrates the
addressing data flow of the look-up table.
The following diagram illustrates the addressing data flow of the look-up table:
Rev. 1.00
25
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
A d d re s s
L a s t p a g e o r
T B H P R e g is te r
T B L P R e g is te r
Instruction
TABRDC[m]
TABRDL[m]
D a ta
1 5 o r 1 6 b its
R e g is te r T B L H
U s e r S e le c te d
R e g is te r
H ig h B y te
L o w B y te
Table Location Bits
b11
b10
b9
PC11 PC10 PC9
1
1
1
b8
b7
b6
b5
b4
b3
b2
b1
b0
PC8
@7
@6
@5
@4
@3
@2
@1
@0
1
@7
@6
@5
@4
@3
@2
@1
@0
Table Location
Note: PC11~PC8:Current Program Counter bits
@7~@0:Table Pointer TBLP bits
For the HT45FH23A, the Table address location is 11 bits, i.e. from b10~b0
For the HT45FH24A, the Table address location is 12 bits, i.e. from b11~b0
Table Program Example
The accompanying example shows how the table pointer and table data is defined and retrieved
from the HT45FH24A device. This example uses raw table data located in the last page which is
stored there using the ORG statement. The value at this ORG statement is “0F00H” which refers to
the start address of the last page within the 4K Program Memory of the device. The table pointer is
setup here to have an initial value of “06H”. This will ensure that the first data read from the data
table will be at the Program Memory address “0F06H” or 6 locations after the start of the last page.
Note that the value for the table pointer is referenced to the first address of the present page if the
“TABRDC [m]” instruction is being used. The high byte of the table data which in this case is equal
to zero will be transferred to the TBLH register automatically when the “TABRDL [m]” instruction
is executed.
Because the TBLH register is a read-only register and cannot be restored, care should be taken
to ensure its protection if both the main routine and Interrupt Service Routine use the table read
instructions. If using the table read instructions, the Interrupt Service Routines may change the
value of TBLH and subsequently cause errors if used again by the main routine. As a rule it is
recommended that simultaneous use of the table read instructions should be avoided. However, in
situations where simultaneous use cannot be avoided, the interrupts should be disabled prior to the
execution of any main routine table-read instructions. Note that all table related instructions require
two instruction cycles to complete their operation.
Rev. 1.00
26
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Table Read Program Example
tempreg1 db ? ; temporary register #1
tempreg2 db ? ; temporary register #2
:
:
mov a,06h ; initialise table pointer - note that this address is referenced
mov tblp,a ; to the last page or present page
mov a, 0Fh ; initialise high table pointer
mov tbhp, a
:
:
tabrdl tempreg1 ; transfers value in table referenced by table pointer to tempregl
; data at prog. memory address “0F06H” transferred to tempreg1 and TBLH
dec tblp ; reduce value of table pointer by one
tabrdl tempreg2 ; transfers value in table referenced by table pointer to tempreg2
; data at prog.memory address “0F05H” transferred to tempreg2 and TBLH
; in this example the data “1AH” is transferred to tempreg1 and data “0FH”
; to register tempreg2 the value “00H” will be transferred to the high
; byte register TBLH
:
:
org F00h ; sets initial address of last page
dc 00Ah, 00Bh, 00Ch, 00Dh, 00Eh, 00Fh, 01Ah, 01Bh
:
:
In Circuit Programming
The provision of Flash type Program Memory provides the user with a means of convenient and easy
upgrades and modifications to their programs on the same devices. As an additional convenience,
Holtek has provided a means of programming the microcontroller in-circuit using a 5-pin interface.
This provides manufacturers with the possibility of manufacturing their circuit boards complete with a programmed or un-programmed microcontroller, and then programming or upgrading the program
at a later stage. This enables product manufacturers to easily keep their manufactured products
supplied with the latest program releases without removal and re-insertion of the devices.
Programming Pins
Function
DATA
Serial Data Input/Output
CLK
Serial Clock
RES
Device Reset
VDD
Power Supply
VSS
Ground
The Program Memory and EEPROM data memory can both be programmed serially in-circuit using
this 5-wire interface. Data is downloaded and uploaded serially on a single pin with an additional
line for the clock. Two additional lines are required for the power supply and one line for the reset.
The technical details regarding the in-circuit programming of the devices are beyond the scope of
this document and will be supplied in supplementary literature.
During the programming process the RES pin will be held low by the programmer disabling the
normal operation of the microcontroller and taking control of the PA0 and PA2 I/O pins for data
and clock programming purposes. The user must there take care to ensure that no other outputs are
connected to these two pins.
Rev. 1.00
27
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Programmer Pin
MCU Pins
RES
PB6
DATA
PA0
CLK
PA2
Programmer and MCU Pins
W r ite r C o n n e c to r
S ig n a ls
P r o g r a m m in g P in s
W r ite r _ V D D
V D D
R E S
R E S
D A T A
D A T A
C L K
C L K
W r ite r _ V S S
V S S
*
*
*
T o o th e r C ir c u it
Note: * may be resistor or capacitor. The resistance of * must be greater than 1kΩ or the capacitance
of * must be less than 1nF.
RAM Data Memory
The Data Memory is a volatile area of 8-bit wide RAM internal memory and is the location where
temporary information is stored.
  
 
  
 
 
Data Memory Structure
Note: Most of the Data Memory bits can be directly manipulated using the “SET [m].i” and
“CLR [m].i” with the exception of a few dedicated bits. The Data Memory can also be
accessed through the memory pointer registers.
Rev. 1.00
28
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Structure
Divided into two sections, the first of these is an area of RAM where special function registers are
located. These registers have fixed locations and are necessary for correct operation of the devices.
Many of these registers can be read from and written to directly under program control, however,
some remain protected from user manipulation. The second area of Data Memory is reserved for
general purpose use. All locations within this area are read and write accessible under program
control.
The overall Data Memory is subdivided into two banks. The Special Purpose Data Memory registers
are accessible in all banks, with the exception of the EEC register at address 40H, which is only
accessible in Bank 1. Switching between the different Data Memory banks is achieved by setting the
Bank Pointer to the correct value. The start address of the Data Memory is the address “00H”.
All microcontroller programs require an area of read/write memory where temporary data can be
stored and retrieved for use later. It is this area of RAM memory that is known as General Purpose
Data Memory. This area of Data Memory is fully accessible by the user program for both read and
write operations. By using the “SET [m].i” and “CLR [m].i” instructions individual bits can be set
or reset under program control giving the user a large range of flexibility for bit manipulation in the
Data Memory.
Special Function Registers
Most of the Special Function Register details will be described in the relevant functional section,
however several registers require a separate description in this section.
    
      







        
     
    
Special Purpose Data Memory
Rev. 1.00
29
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Indirect Addressing Registers – IAR0, IAR1
The Indirect Addressing Registers, IAR0 and IAR1, although having their locations in normal RAM
register space, do not actually physically exist as normal registers. The method of indirect addressing
for RAM data manipulation uses these Indirect Addressing Registers and Memory Pointers, in
contrast to direct memory addressing, where the actual memory address is specified. Actions on the
IAR0 and IAR1 registers will result in no actual read or write operation to these registers but rather
to the memory location specified by their corresponding Memory Pointer, MP0 or MP1. Acting as
a pair, IAR0 with MP0 and IAR1 with MP1, can together access data from the Data Memory. As
the Indirect Addressing Registers are not physically implemented, reading the Indirect Addressing
Registers indirectly will return a result of “00H” and writing to the registers indirectly will result in
no operation.
Memory Pointers – MP0, MP1
Two Memory Pointers, known as MP0 and MP1 are provided. These Memory Pointers are
physically implemented in the Data Memory and can be manipulated in the same way as normal
registers providing a convenient way with which to address and track data. When any operation to
the relevant Indirect Addressing Registers is carried out, the actual address that the microcontroller
is directed to, is the address specified by the related Memory Pointer. MP0, together with Indirect
Addressing Register, IAR0, are used to access data from Bank 0, while MP1 and IAR1 are used to
access data from all banks according to BP register. Direct Addressing can only be used with Bank 0,
all other Banks must be addressed indirectly using MP1 and IAR1.
The following example shows how to clear a section of four Data Memory locations already defined
as locations adres1 to adres4.
Indirect Addressing Program Example
data .section "data"
adres1 db ?
adres2 db ?
adres3 db ?
adres4 db ?
block db ?
code .section at 0 code
org 00h
start:
mov a,04h;
mov block,a
mov a,offset adres1 ;
mov mp0,a ;
loop:
clr IAR0 ;
inc mp0;
sdz block;
jmp loop
continue:
setup size of block
Accumulator loaded with first RAM address
setup memory pointer with first RAM address
clear the data at address defined by MP0
increment memory pointer
check if last memory location has been cleared
The important point to note here is that in the example shown above, no reference is made to specific
Data Memory addresses.
Rev. 1.00
30
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bank Pointer – BP
The Data Memory is divided into two Banks, known as Bank 0 and Bank 1. A Bank Pointer, which
is bit 0 of the Bank Pointer register is used to select the required Data Memory bank. Only data in
Bank 0 can be directly addressed as data in Bank 1 must be indirectly addressed using Memory
Pointer MP1 and Indirect Addressing Register IAR1. Using Memory Pointer MP0 and Indirect
Addressing Register IAR0 will always access data from Bank 0, irrespective of the value of the
Bank Pointer. Memory Pointer MP1 and Indirect Addressing Register IAR1 can indirectly address
data in either Bank 0 or Bank 1 depending upon the value of the Bank Pointer.
The Data Memory is initialised to Bank 0 after a reset, except for the WDT time-out reset in the
Idle/Sleep Mode, in which case, the Data Memory bank remains unaffected. It should be noted that
Special Function Data Memory is not affected by the bank selection, which means that the Special
Function Registers can be accessed from within either Bank 0 or Bank 1. Directly addressing the
Data Memory will always result in Bank 0 being accessed irrespective of the value of the Bank
Pointer.
BP Register
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
—
—
—
DMBP0
R/W
—
—
—
—
—
—
—
R/W
POR
—
—
—
—
—
—
—
0
Bit 7 ~ 1
Unimplemented, read as “0”
Bit 0
DMBP0: Select Data Memory Banks
0: Bank 0
1: Bank 1
Accumulator – ACC
The Accumulator is central to the operation of any microcontroller and is closely related with
operations carried out by the ALU. The Accumulator is the place where all intermediate results
from the ALU are stored. Without the Accumulator it would be necessary to write the result of
each calculation or logical operation such as addition, subtraction, shift, etc., to the Data Memory
resulting in higher programming and timing overheads. Data transfer operations usually involve
the temporary storage function of the Accumulator; for example, when transferring data between
one user defined register and another, it is necessary to do this by passing the data through the
Accumulator as no direct transfer between two registers is permitted.
Rev. 1.00
31
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Program Counter Low Register – PCL
To provide additional program control functions, the low byte of the Program Counter is made
accessible to programmers by locating it within the Special Purpose area of the Data Memory. By
manipulating this register, direct jumps to other program locations are easily implemented. Loading
a value directly into this PCL register will cause a jump to the specified Program Memory location.
However, as the register is only 8-bit wide, only jumps within the current Program Memory page are
permitted. When such operations are used, note that a dummy cycle will be inserted.
Look-up Table Registers – TBLP, TBHP, TBLH
These three special function registers are used to control operation of the look-up table which is
stored in the Program Memory. TBLP and TBHP are the table pointers and indicate the location
where the table data is located. Their value must be setup before any table read commands are
executed. Their value can be changed, for example using the “INC” or “DEC” instructions, allowing
for easy table data pointing and reading. TBLH is the location where the high order byte of the table
data is stored after a table read data instruction has been executed. Note that the lower order table
data byte is transferred to a user defined location.
Status Register – STATUS
This 8-bit register contains the zero flag (Z), carry flag (C), auxiliary carry flag (AC), overflow flag
(OV), power down flag (PDF), and watchdog time-out flag (TO). These arithmetic/logical operation
and system management flags are used to record the status and operation of the microcontroller.
With the exception of the TO and PDF flags, bits in the status register can be altered by instructions
like most other registers. Any data written into the status register will not change the TO or PDF flag.
In addition, operations related to the status register may give different results due to the different
instruction operations. The TO flag can be affected only by a system power-up, a WDT time-out or
by executing the “CLR WDT” or “HALT” instruction. The PDF flag is affected only by executing
the “HALT” or “CLR WDT” instruction or during a system power-up.
The Z, OV, AC and C flags generally reflect the status of the latest operations.
In addition, on entering an interrupt sequence or executing a subroutine call, the status register will
not be pushed onto the stack automatically. If the contents of the status registers are important and
if the interrupt routine can change the status register, precautions must be taken to correctly save it.
Note that bits 0~3 of the STATUS register are both readable and writeable bits.
Rev. 1.00
32
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
STATUS Register
Bit
7
6
5
4
3
2
1
0
Name
—
—
TO
PDF
OV
Z
AC
C
R/W
—
—
R
R
R/W
R/W
R/W
R/W
POR
—
—
0
0
x
x
x
x
“x” unknown
Rev. 1.00
Bit 7~6
Unimplemented, read as "0"
Bit 5
TO: Watchdog Time-Out flag
0: After power up or executing the “CLR WDT” or “HALT” instruction
1: A watchdog time-out occurred.
Bit 4
PDF: Power down flag
0: After power up or executing the “CLR WDT” instruction
1: By executing the “HALT” instruction
Bit 3
OV: Overflow flag
0: no overflow
1: an operation results in a carry into the highest-order bit but not a carry out of the
highest-order bit or vice versa.
Bit 2
Z: Zero flag
0: The result of an arithmetic or logical operation is not zero
1: The result of an arithmetic or logical operation is zero
Bit 1
AC: Auxiliary flag
0: no auxiliary carry
1: an operation results in a carry out of the low nibbles in addition, or no borrow
from the high nibble into the low nibble in subtraction
Bit 0
C: Carry flag
0: no carry-out
1: an operation results in a carry during an addition operation or if a borrow does not
take place during a subtraction operation
C is also affected by a rotate through carry instruction.
33
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
EEPROM Data Memory
One of the special features in the devices is its internal EEPROM Data Memory. EEPROM, which
stands for Electrically Erasable Programmable Read Only Memory, is by its nature a non-volatile
form of memory, with data retention even when its power supply is removed. By incorporating
this kind of data memory, a whole new host of application possibilities are made available to the
designer. The availability of EEPROM storage allows information such as product identification
numbers, calibration values, specific user data, system setup data or other product information to
be stored directly within the product microcontroller. The process of reading and writing data to the
EEPROM memory has been reduced to a very trivial affair.
EEPROM Data Memory Structure
The EEPROM Data Memory capacity is 64×8 bits. Unlike the Program Memory and RAM Data
Memory, the EEPROM Data Memory is not directly mapped into memory space and is therefore
not directly accessible in the same way as the other types of memory. Instead it has to be accessed
indirectly through the EEPROM control registers.
EEPROM Registers
Three registers control the overall operation of the internal EEPROM Data Memory. These are the
address register, EEA, the data register, EED and a single control register, EEC. As both the EEA
and EED registers are located in Bank 0, they can be directly accessed in the same was as any other
Special Function Register. The EEC register however, being located in Bank1, cannot be directly
addressed directly and can only be read from or written to indirectly using the MP1 Memory Pointer
and Indirect Addressing Register, IAR1. Because the EEC control register is located at address 40H
in Bank 1, the MP1 Memory Pointer must first be set to the value 40H and the Bank Pointer register,
BP, set to the value, 01H, before any operations on the EEC register are executed.
EEPROM Register List
Name
Bit
7
6
5
4
3
2
1
0
D0
EEA
—
—
D5
D4
D3
D2
D1
EED
D7
D6
D5
D4
D3
D2
D1
D0
EEC
—
—
—
—
WREN
WR
RDEN
RD
EEA Register
Bit
7
6
5
4
3
2
1
0
Name
—
—
D5
D4
D3
D2
D1
D0
R/W
—
—
R/W
R/W
R/W
R/W
R/W
R/W
POR
—
—
x
x
x
x
x
x
“x” unknown
Rev. 1.00
Bit 7 ~ 6
Unimplemented, read as “0”
Bit 5 ~ 0
D5~D0: Data EEPROM address
Data EEPROM address bit 5 ~ bit 0
34
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
EED Register
Bit
7
6
5
4
3
2
1
0
Name
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
x
x
x
x
x
x
x
x
“x” unknown
Bit 7 ~ 0
D7~D0: Data EEPROM data
Data EEPROM data bit 7 ~ bit 0
EEC Register
Bit
7
6
5
4
3
2
1
Name
—
—
—
—
R/W
—
—
—
—
POR
—
—
—
—
0
WREN
WR
RDEN
RD
R/W
R/W
R/W
R/W
0
0
0
0
Bit 7 ~ 4
Unimplemented, read as “0”
Bit 3
WREN: Data EEPROM Write Enable
0: Disable
1: Enable
This is the Data EEPROM Write Enable Bit which must be set high before Data
EEPROM write operations are carried out. Clearing this bit to zero will inhibit Data
EEPROM write operations.
Bit 2
WR: EEPROM Write Control
0: Write cycle has finished
1: Activate a write cycle
This is the Data EEPROM Write Control Bit and when set high by the application
program will activate a write cycle. This bit will be automatically reset to zero by the
hardware after the write cycle has finished. Setting this bit high will have no effect if
the WREN has not first been set high.
Bit 1
RDEN: Data EEPROM Read Enable
0: Disable
1: Enable
This is the Data EEPROM Read Enable Bit which must be set high before Data
EEPROM read operations are carried out. Clearing this bit to zero will inhibit Data
EEPROM read operations.
Bit 0
RD: EEPROM Read Control
0: Read cycle has finished
1: Activate a read cycle
This is the Data EEPROM Read Control Bit and when set high by the application
program will activate a read cycle. This bit will be automatically reset to zero by the
hardware after the read cycle has finished. Setting this bit high will have no effect if
the RDEN has not first been set high.
Note: The WREN, WR, RDEN and RD can not be set to “1” at the same time in one instruction. The
WR and RD can not be set to “1” at the same time.
Rev. 1.00
35
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Reading Data from the EEPROM
To read data from the EEPROM, the read enable bit, RDEN, in the EEC register must first be set
high to enable the read function. The EEPROM address of the data to be read must then be placed
in the EEA register. If the RD bit in the EEC register is now set high, a read cycle will be initiated.
Setting the RD bit high will not initiate a read operation if the RDEN bit has not been set. When
the read cycle terminates, the RD bit will be automatically cleared to zero, after which the data can
be read from the EED register. The data will remain in the EED register until another read or write
operation is executed. The application program can poll the RD bit to determine when the data is
valid for reading.
Writing Data to the EEPROM
The EEPROM address of the data to be written must first be placed in the EEA register and the data
placed in the EED register. To write data to the EEPROM, the write enable bit, WREN, in the EEC
register must first be set high to enable the write function. After this, the WR bit in the EEC register
must be immediately set high to initiate a write cycle. These two instructions must be executed
consecutively. The global interrupt bit EMI should also first be cleared before implementing any
write operations, and then set again after the write cycle has started. Note that setting the WR bit
high will not initiate a write cycle if the WREN bit has not been set. As the EEPROM write cycle is
controlled using an internal timer whose operation is asynchronous to microcontroller system clock,
a certain time will elapse before the data will have been written into the EEPROM. Detecting when
the write cycle has finished can be implemented either by polling the WR bit in the EEC register or
by using the EEPROM interrupt. When the write cycle terminates, the WR bit will be automatically
cleared to zero by the microcontroller, informing the user that the data has been written to the
EEPROM. The application program can therefore poll the WR bit to determine when the write cycle
has ended.
Write Protection
Protection against inadvertent write operation is provided in several ways. After the devices
are powered-on the Write Enable bit in the control register will be cleared preventing any write
operations. Also at power-on the Bank Pointer, BP, will be reset to zero, which means that Data
Memory Bank 0 will be selected. As the EEPROM control register is located in Bank 1, this adds a
further measure of protection against spurious write operations. During normal program operation,
ensuring that the Write Enable bit in the control register is cleared will safeguard against incorrect
write operations.
EEPROM Interrupt
The EEPROM write or read interrupt is generated when an EEPROM write or read cycle has ended.
The EEPROM interrupt must first be enabled by setting the EE2I bit in the relevant interrupt register.
However as the EEPROM is contained within a Multi-function Interrupt, the associated multifunction interrupt enable bit must also be set. When an EEPROM write cycle ends, the E2F request
flag and its associated multi-function interrupt request flag will both be set. If the global, EEPROM
and Multi-function interrupts are enabled and the stack is not full, a jump to the associated Multifunction Interrupt vector will take place. When the interrupt is serviced only the Multi-function
interrupt flag will be automatically reset, the EEPROM interrupt flag must be manually reset by the
application program.
Rev. 1.00
36
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Programming Considerations
Care must be taken that data is not inadvertently written to the EEPROM. Protection can be
Periodic by ensuring that the Write Enable bit is normally cleared to zero when not writing. Also
the Bank Pointer could be normally cleared to zero as this would inhibit access to Bank 1 where
the EEPROM control register exist. Although certainly not necessary, consideration might be given
in the application program to the checking of the validity of new write data by a simple read back
process. When writing data the WR bit must be set high immediately after the WREN bit has been
set high, to ensure the write cycle executes correctly. The global interrupt bit EMI should also be
cleared before a write cycle is executed and then re-enabled after the write cycle starts. Note that
the devices should not enter the IDLE or SLEEP mode until the EEPROM read or write operation is
totally complete. Otherwise, the EEPROM read or write operation will fail.
Programming Examples
Reading data from the EEPROM – polling method
MOV A, EEPROM_ADRES MOV EEA, A
MOV A, 040H MOV MP1, A MOV A, 01H MOV BP, A
SET IAR1.1 SET IAR1.0
BACK:
SZ IAR1.0 JMP BACK
CLR IAR1 CLR BP
MOV A, EED MOV READ_DATA, A
; user defined address
; setup memory pointer MP1
; MP1 points to EEC register
; setup Bank Pointer
; set RDEN bit, enable read operations
; start Read Cycle - set RD bit
; check for read cycle end
; disable EEPROM read/write
; move read data to register
Writing Data to the EEPROM – polling method
MOV A, EEPROM_ADRES MOV EEA, A
MOV A, EEPROM_DATA MOV EED, A
MOV A, 040H MOV MP1, A MOV A, 01H MOV BP, A
CLR EMI
SET IAR1.3
SET IAR1.2
SET EMI
BACK:
SZ IAR1.2 JMP BACK
CLR IAR1 CLR BP
Rev. 1.00
; user defined address
; user defined data
; setup memory pointer MP1
; MP1 points to EEC register
; setup Bank Pointer
; set WREN bit, enable write operations
; start Write Cycle - set WR bit
; check for write cycle end
; disable EEPROM read/write
37
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Oscillators
Various oscillator options offer the user a wide range of functions according to their various
application requirements. The flexible features of the oscillator functions ensure that the best
optimisation can be achieved in terms of speed and power saving. Oscillator selections and operation
are selected through a combination of configuration options and registers.
Oscillator Overview
In addition to being the source of the main system clock the oscillators also provide clock sources
for the Watchdog Timer and Time Base Interrupts. External oscillators requiring some external
components as well as fully integrated internal oscillators, requiring no external components,
are provided to form a wide range of both fast and slow system oscillators. All oscillator options
are selected through the configuration options. The higher frequency oscillators provide higher
performance but carry with it the disadvantage of higher power requirements, while the opposite
is of course true for the lower frequency oscillators. With the capability of dynamically switching
between fast and slow system clock, the devices have the flexibility to optimize the performance/
power ratio, a feature especially important in power sensitive portable applications.
Type
Name
Freq.
External Crystal
HXT
400kHz~8MHz
Internal High Speed RC
HIRC
910kHz, 2/4/8MHz
External Clock
EC
400kHz~8MHz
External Low Speed Crystal
LXT
32.768kHz
Internal Low Speed RC
LIRC
32kHz
Pins
OSC1/OSC2
—
OSC1
XT1/XT2
—
Oscillator Types
System Clock Configurations
There are five methods of generating the system clock, three high speed oscillators and two low
speed oscillators. The high speed oscillators are the external crystal/ ceramic oscillator, external RC
network oscillator, external clock and the internal 910kHz, 2MHz, 4MHz or 8MHz RC oscillator.
The two low speed oscillators are the internal 32kHz RC oscillator and the external 32.768kHz
crystal oscillator.
Rev. 1.00
38
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver



Š 
 
­ € ‚
€  ƒ € „ 
† ‡
Œ Š ‹
ˆ  ‰ Š Š  ‹ Ž ‘ ’
System Clock Configuration
Selecting whether the low or high speed oscillator is used as the system oscillator is implemented
using the HLCLK bit and CKS2~CKS0 bits in the SMOD register and as the system clock can
be dynamically selected. The actual source clock used for each of the high speed and low speed
oscillators is chosen via configuration options. The frequency of the slow speed or high speed
system clock is also determined using the HLCLK bit and CKS2~CKS0 bits in the SMOD register.
Note that two oscillator selections must be made namely one high speed and one low speed system
oscillators. It is not possible to choose a no-oscillator selection for either the high or low speed
oscillator.
External Crystal/Ceramic Oscillator – HXT
The External Crystal/ Ceramic System Oscillator is one of the high frequency oscillator choices,
which is selected via configuration option. For most crystal oscillator configurations, the simple
connection of a crystal across OSC1 and OSC2 will create the necessary phase shift and feedback for
oscillation, without requiring external capacitors. However, for some crystal types and frequencies,
to ensure oscillation, it may be necessary to add two small value capacitors, C1 and C2. Using a
ceramic resonator will usually require two small value capacitors, C1 and C2, to be connected as
shown for oscillation to occur. The values of C1 and C2 should be selected in consultation with the
crystal or resonator manufacturer’s specification.
For oscillator stability and to minimise the effects of noise and crosstalk, it is important to ensure
that the crystal and any associated resistors and capacitors along with interconnecting lines are all
located as close to the MCU as possible.
Rev. 1.00
39
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
     Crystal/Resonator Oscillator – HXT
Crystal Oscillator C1 and C2 Values
Crystal Frequency
C1
C2
8MHz
0pF
0pF
4MHz
0pF
0pF
1MHz
100pF
100pF
Note:C1 and C2 values are for guidance only.
Crystal Recommended Capacitor Values
External Oscillator – EC
The system clock can also be supplied by an externally supplied clock giving users a method of
synchronising their external hardware to the microcontroller operation. This is selected using
a configuration option and supplying the clock on pin OSC1. Pin OSC2 should be left floating
if the external oscillator is used. The internal oscillator circuit contains a filter circuit to reduce
the possibility of erratic operation due to noise on the oscillator pin, however as the filter circuit
consumes a certain amount of power, a configuration option exists to turn this filter off. Not using
the internal filter should be considered in power sensitive applications and where the externally
supplied clock is of a high integrity and supplied by a low impedance source.
Internal RC Oscillator – HIRC
The internal RC oscillator is a fully integrated system oscillator requiring no external components.
The internal RC oscillator has four fixed frequencies of either 910kHz, 2MHz, 4MHz or 8MHz.
Device trimming during the manufacturing process and the inclusion of internal frequency
compensation circuits are used to ensure that the influence of the power supply voltage, temperature
and process variations on the oscillation frequency are minimised. As a result, at a power supply of
3.3V and at a temperature of 25˚C degrees, the fixed oscillation frequency of 910kHz, 2MHz, 4MHz
or 8MHz will have a tolerance within 2%. Note that if this internal system clock option is selected,
as it requires no external pins for its operation, I/O pins PC0 and PC1 are free for use as normal I/O
pins.
External 32.768kHz Crystal Oscillator – LXT
The External 32.768kHz Crystal System Oscillator is one of the low frequency oscillator choices,
which is selected via configuration option. This clock source has a fixed frequency of 32.768kHz
and requires a 32.768kHz crystal to be connected between pins XT1 and XT2. The external resistor
and capacitor components connected to the 32.768kHz crystal are necessary to provide oscillation.
For applications where precise frequencies are essential, these components may be required to
provide frequency compensation due to different crystal manufacturing tolerances. During power-up
there is a time delay associated with the LXT oscillator waiting for it to start-up.
Rev. 1.00
40
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
C1
XT1
Inte�nal RC
Oscillato�
RP
3�.�68kHz
Internal
Oscillator
Circuit
XT�
C�
To inte�nal
ci�cuits
�ote: 1. RP� C1 and C� a�e �equi�ed.
�. Although not shown pins have a pa�asitic capacitance of a�ound �pF.
External LXT Oscillator
When the microcontroller enters the SLEEP or IDLE Mode, the system clock is switched off to stop
microcontroller activity and to conserve power. However, in many microcontroller applications
it may be necessary to keep the internal timers operational even when the microcontroller is in
the SLEEP or IDLE Mode. To do this, another clock, independent of the system clock, must be
provided.
However, for some crystals, to ensure oscillation and accurate frequency generation, it is necessary
to add two small value external capacitors, C1 and C2. The exact values of C1 and C2 should be
selected in consultation with the crystal or resonator manufacturer's specification. The external
parallel feedback resistor, Rp, is required.
Some configuration options determine if the XT1/XT2 pins are used for the LXT oscillator or as I/O
pins.
• If the LXT oscillator is not used for any clock source, the XT1/XT2 pins can be used as normal I/O
pins.
• If the LXT oscillator is used for any clock source, the 32.768kHz crystal should be connected to
the XT1/XT2 pins.
For oscillator stability and to minimise the effects of noise and crosstalk, it is important to ensure
that the crystal and any associated resistors and capacitors along with interconnecting lines are all
located as close to the MCU as possible.
LXT Oscillator C1 and C2 Values
Crystal Frequency
C1
C2
32.768kHz
10pF
10pF
Note: 1. C1 and C2 values are for guidance only.
2. RP=5M~10MΩ is recommended.
32.768kHz Crystal Recommended Capacitor Values
LXT Oscillator Low Power Function
The LXT oscillator can function in one of two modes, the Quick Start Mode and the Low Power
Mode. The mode selection is executed using the LXTLP bit in the TBC register.
LXTLP Bit
LXT Mode
0
Quick Start
1
Low-power
After power on the LXTLP bit will be automatically cleared to zero ensuring that the LXT oscillator
is in the Quick Start operating mode. In the Quick Start Mode the LXT oscillator will power up
and stabilise quickly. However, after the LXT oscillator has fully powered up it can be placed
into the Low-power mode by setting the LXTLP bit high. The oscillator will continue to run but
with reduced current consumption, as the higher current consumption is only required during the
LXT oscillator start-up. In power sensitive applications, such as battery applications, where power
Rev. 1.00
41
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
consumption must be kept to a minimum, it is therefore recommended that the application program
sets the LXTLP bit high about 2 seconds after power-on.
It should be noted that, no matter what condition the LXTLP bit is set to, the LXT oscillator will
always function normally, the only difference is that it will take more time to start up if in the Lowpower mode.
Internal 32kHz Oscillator – LIRC
The Internal 32kHz System Oscillator is one of the low frequency oscillator choices, which is
selected via configuration option. It is a fully integrated RC oscillator with a typical frequency of
32kHz at 5V, requiring no external components for its implementation. Device trimming during
the manufacturing process and the inclusion of internal frequency compensation circuits are used
to ensure that the influence of the power supply voltage, temperature and process variations on the
oscillation frequency are minimised. As a result, at a power supply of 5V and at a temperature of
25˚C degrees, the fixed oscillation frequency of 32kHz will have a tolerance within 10%.
Supplementary Oscillators
The low speed oscillators, in addition to providing a system clock source are also used to provide
a clock source to two other device functions. These are the Watchdog Timer and the Time Base
Interrupts.
Operating Modes and System Clocks
Present day applications require that their microcontrollers have high performance but often still
demand that they consume as little power as possible, conflicting requirements that are especially
true in battery powered portable applications. The fast clocks required for high performance will
by their nature increase current consumption and of course vice-versa, lower speed clocks reduce
current consumption. As Holtek has provided the devices with both high and low speed clock
sources and the means to switch between them dynamically, the user can optimise the operation of
their microcontroller to achieve the best performance/power ratio.
System Clocks
The devices have many different clock sources for both the CPU and peripheral function operation.
By providing the user with a wide range of clock options using configuration options and register
programming, a clock system can be configured to obtain maximum application performance.
The main system clock, can come from either a high frequency, fH, or low frequency, fL, source, and
is selected using the HLCLK bit and CKS2~CKS0 bits in the SMOD register. The high speed system
clock can be sourced from either an HXT, EC or HIRC oscillator, selected via a configuration option.
The low speed system clock source can be sourced from internal clock fL. If fL is selected then it
can be sourced by either the LXT or LIRC oscillators, selected via a configuration option. The other
choice, which is a divided version of the high speed system oscillator has a range of fH/2~fH/64.
There are two additional internal clocks for the peripheral circuits, the substitute clock, fSUB, and
the Period Time Clock, fTBC. Each of these internal clocks are sourced by either the LXT or LIRC
oscillators, selected via configuration options. The fSUB clock is used to provide a substitute clock for
the microcontroller just after a wake-up has occurred to enable faster wake-up times.
Together with fSYS/4 it is also used as one of the clock sources for the Watchdog timer. The fTB clock
is used as a source for the Time Base 0/1 interrupt functions.
Rev. 1.00
42
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
System Operation Modes
There are six different modes of operation for the microcontroller, each one with its own
special characteristics and which can be chosen according to the specific performance and
power requirements of the application. There are two modes allowing normal operation of the
microcontroller, the NORMAL Mode and SLOW Mode. The remaining four modes, the SLEEP0,
SLEEP1, IDLE0 and IDLE1 Mode are used when the microcontroller CPU is switched off to
conserve power.
  
  „   ‚
Œ   
  ­
ƒ
     € ‚
­

‡ 
 ‚ ˆ  ‰      
† Š ‹ „  Œ Œ Ž  Œ Ž  ‘ ’ “

­
‡ 


‡ 
­
† 
Device Clock Configurations
Note: When the system clock source fSYS is switched to fL from fH, the high speed oscillation will stop to conserve
the power. Thus there is no fH~fH/64 for peripheral circuit to use.
Rev. 1.00
43
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Description
Operation
Mode
CPU
fSYS
fSUB
fS
fTBC
NORMAL Mode
On
fH~ fH/64
On
On
On
SLOW Mode
On
fL
On
On
On
IDLE0 Mode
Off
Off
On
On/Off
On
IDLE1 Mode
Off
On
On
On
On
SLEEP0 Mode
Off
Off
Off
Off
Off
SLEEP1 Mode
Off
Off
On
On
Off
NORMAL Mode
As the name suggests this is one of the main operating modes where the microcontroller has all of
its functions operational and where the system clock is provided by one of the high speed oscillators.
This mode operates allowing the microcontroller to operate normally with a clock source will come
from one of the high speed oscillators, either the HXT, HIRC or EC oscillators. The high speed
oscillator will however first be divided by a ratio ranging from 1 to 64, the actual ratio being selected
by the CKS2~CKS0 and HLCLK bits in the SMOD register. Although a high speed oscillator is
used, running the microcontroller at a divided clock ratio reduces the operating current.
SLOW Mode
This is also a mode where the microcontroller operates normally although now with a slower speed
clock source. The clock source used will be from one of the low speed oscillators, either the LXT
or the LIRC. Running the microcontroller in this mode allows it to run with much lower operating
currents. In the SLOW Mode, the fH is off.
SLEEP0 Mode
The SLEEP Mode is entered when an HALT instruction is executed and when the IDLEN bit in the
SMOD register is low. In the SLEEP0 mode the CPU will be stopped, and the fSUB and fS clocks will
be stopped too, and the Watchdog Timer function is disabled. In this mode, the LVDEN is must set
to “0”. If the LVDEN is set to “1”, it won’t enter the SLEEP0 Mode.
SLEEP1 Mode
The SLEEP Mode is entered when an HALT instruction is executed and when the IDLEN bit in
the SMOD register is low. In the SLEEP1 mode the CPU will be stopped. However the fSUB and fS
clocks will continue to operate if the LVDEN is “1” or the Watchdog Timer function is enabled and
if its clock source is chosen via configuration option to come from the fSUB.
IDLE0 Mode
The IDLE0 Mode is entered when a HALT instruction is executed and when the IDLEN bit in the
SMOD register is high and the FSYSON bit in the WDTC register is low. In the IDLE0 Mode the
system oscillator will be inhibited from driving the CPU but some peripheral functions will remain
operational such as the Watchdog Timer, Time Base 0 and SIM. In the IDLE0 Mode, the system
oscillator will be stopped. In the IDLE0 Mode the Watchdog Timer clock, fS, will either be on or
off depending upon the fS clock source. If the source is fSYS/4 then the fS clock will be off, and if the
source comes from fSUB then fS will be on.
Rev. 1.00
44
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
IDLE1 Mode
The IDLE1 Mode is entered when an HALT instruction is executed and when the IDLEN bit in the
SMOD register is high and the FSYSON bit in the WDTC register is high. In the IDLE1 Mode the
system oscillator will be inhibited from driving the CPU but may continue to provide a clock source
to keep some peripheral functions operational such as the Watchdog Timer, Time Base 0 and SIM. In
the IDLE1 Mode, the system oscillator will continue to run, and this system oscillator may be high
speed or low speed system oscillator. In the IDLE1 Mode the Watchdog Timer clock, fS, will be on. If
the source is fSYS/4 then the fS clock will be on, and if the source comes from fSUB then fS will be on.
Control Register
A single register, SMOD, is used for overall control of the internal clocks within the devices.
SMOD Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
CKS2
CKS1
CKS0
FSTEN
LTO
HTO
IDLEN
HLCLK
R/W
R/W
R/W
R/W
R/W
R
R
R/W
R/W
POR
0
0
0
0
0
0
1
1
Bit 7~5
CKS2~CKS0: The system clock selection when HLCLK is “0”
000: fL (fLXT or fLIRC)
001: fL (fLXT or fLIRC)
010: fH/64
011: fH/32
100: fH/16
101: fH/8
110: fH/4
111: fH/2
These three bits are used to select which clock is used as the system clock source. In
addition to the system clock source, which can be either the LXT or LIRC, a divided
version of the high speed system oscillator can also be chosen as the system clock
source.
Bit 4
FSTEN: Fast Wake-up Control (only for HXT)
0: Disable
1: Enable
This is the Fast Wake-up Control bit which determines if the fSUB clock source is
initially used after the devices wake up. When the bit is high, the fSUB clock source can
be used as a temporary system clock to provide a faster wake up time as the fSUB clock
is available.
Bit 3
LTO: Low speed system oscillator ready flag
0: Not ready
1: Ready
This is the low speed system oscillator ready flag which indicates when the low speed
system oscillator is stable after power on reset or a wake-up has occurred. The flag
will be low when in the SLEEP0 Mode but after a wake-up has occurred, the flag will
change to a high level after 1024 clock cycles if the LXT oscillator is used and 1~2
clock cycles if the LIRC oscillator is used.
45
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit 2
HTO: High speed system oscillator ready flag
0: Not ready
1: Ready
This is the high speed system oscillator ready flag which indicates when the high speed
system oscillator is stable. This flag is cleared to “0” by hardware when the devices are
powered on and then changes to a high level after the high speed system oscillator is
stable. Therefore this flag will always be read as “1” by the application program after
devices power-on. The flag will be low when in the SLEEP or IDLE0 Mode but after
a wake-up has occurred, the flag will change to a high level after 1024 clock cycles if
the HXT oscillator is used and after 15~16 clock cycles if the HIRC oscillator is used.
Bit 1
IDLEN: IDLE Mode control
0: Disable
1: Enable
This is the IDLE Mode Control bit and determines what happens when the HALT
instruction is executed. If this bit is high, when a HALT instruction is executed the
devices will enter the IDLE Mode. In the IDLE1 Mode the CPU will stop running
but the system clock will continue to keep the peripheral functions operational, if
FSYSON bit is high. If FSYSON bit is low, the CPU and the system clock will all stop
in IDLE0 mode. If the bit is low the devices will enter the SLEEP Mode when a HALT
instruction is executed.
Bit 0
HLCLK: system clock selection
0: fH/2 ~ fH/64 or fL
1: fH
This bit is used to select if the fH clock or the fH/2 ~ fH/64 or fL clock is used as
the system clock. When the bit is high the fH clock will be selected and if low the
fH/2~fH/64 or fL clock will be selected. When system clock switches from the fH clock
to the fL clock and the fH clock will be automatically switched off to conserve power.
Fast Wake-up
To minimise power consumption the devices can enter the SLEEP or IDLE0 Mode, where the
system clock source to the devices will be stopped. However when the devices are woken up again,
it can take a considerable time for the original system oscillator to restart, stabilise and allow normal
operation to resume. To ensure the devices are up and running as fast as possible a Fast Wakeup function is provided, which allows fSUB, namely either the LXT or LIRC oscillator, to act as a
temporary clock to first drive the system until the original system oscillator has stabilised. As the
clock source for the Fast Wake-up function is fSUB, the Fast Wake-up function is only available in
the SLEEP1 and IDLE0 modes. When the devices are woken up from the SLEEP0 mode, the Fast
Wake-up function has no effect because the fSUB clock is stopped. The Fast Wake-up enable/disable
function is controlled using the FSTEN bit in the SMOD register.
If the HXT oscillator is selected as the NORMAL Mode system clock, and if the Fast Wake-up
function is enabled, then it will take one to two tSUB clock cycles of the LIRC or LXT oscillator for
the system to wake-up. The system will then initially run under the fSUB clock source until 1024
HXT clock cycles have elapsed, at which point the HTO flag will switch high and the system will
switch over to operating from the HXT oscillator.
If the EC or HIRC oscillators or LIRC oscillator is used as the system oscillator then it will take
15~16 clock cycles of the EC or HIRC or 1~2 cycles of the LIRC to wake up the system from the
SLEEP or IDLE0 Mode. The Fast Wake-up bit, FSTEN will have no effect in these cases.
Rev. 1.00
46
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
System FSTEN
Oscillator
Bit
0
HXT
1
Wake-up Time
(SLEEP0 Mode)
Wake-up Time
(SLEEP1 Mode)
Wake-up Time
(IDLE0 Mode)
Wake-up Time
(IDLE1 Mode)
1024 HXT cycles
1024 HXT cycles
1024 HXT cycles
1~2 fSUB cycles
(System runs with fSUB first for 1024
1~2 HXT cycles
HXT cycles and then switches over to
run with the HXT clock)
1~2 HXT cycles
15~16 EC cycles
15~16 EC cycles
EC
X
HIRC
X
LIRC
X
1~2 LIRC cycles
1~2 LIRC cycles
1~2 LIRC cycles
LXT
X
1024 LXT cycles
1024 LXT cycles
1~2 LXT cycles
15~16 HIRC cycles 15~16 HIRC cycles
1~2 EC cycles
1~2 HIRC cycles
Wake-Up Times
Note that if the Watchdog Timer is disabled, which means that the LXT and LIRC are all both off, then
there will be no Fast Wake-up function available when the devices wake-up from the SLEEP0 Mode.
Operating Mode Switching
The devices can switch between operating modes dynamically allowing the user to select the best
performance/power ratio for the present task in hand. In this way microcontroller operations that
do not require high performance can be executed using slower clocks thus requiring less operating
current and prolonging battery life in portable applications.
In simple terms, Mode Switching between the NORMAL Mode and SLOW Mode is executed
using the HLCLK bit and CKS2~CKS0 bits in the SMOD register while Mode Switching from the
NORMAL/SLOW Modes to the SLEEP/IDLE Modes is executed via the HALT instruction. When
a HALT instruction is executed, whether the devices enter the IDLE Mode or the SLEEP Mode is
determined by the condition of the IDLEN bit in the SMOD register and FSYSON in the WDTC
register.
When the HLCLK bit switches to a low level, which implies that clock source is switched from the
high speed clock source, fH, to the clock source, fH/2~fH/64 or fL. If the clock is from the fL, the high
speed clock source will stop running to conserve power. When this happens it must be noted that the
fH/16 and fH/64 internal clock sources will also stop running, which may affect the operation of other
internal functions such as the SIM. The accompanying flowchart shows what happens when the
devices move between the various operating modes.
Rev. 1.00
47
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
­ €    
  ­ €  NORMAL Mode to SLOW Mode Switching
When running in the NORMAL Mode, which uses the high speed system oscillator, and therefore
consumes more power, the system clock can switch to run in the SLOW Mode by set the HLCLK bit
to “0” and set the CKS2~CKS0 bits to “000” or “001” in the SMOD register. This will then use the
low speed system oscillator which will consume less power. Users may decide to do this for certain
operations which do not require high performance and can subsequently reduce power consumption.
The SLOW Mode is sourced from the LXT or the LIRC oscillators and therefore requires these
oscillators to be stable before full mode switching occurs. This is monitored using the LTO bit in the
SMOD register.
Rev. 1.00
48
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
  
   ­   ­       ­   ­
 €‚ ƒ    ­   ­
 €‚ ƒ    ­   ­
 Rev. 1.00
49
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
SLOW Mode to NORMAL Mode Switching
In SLOW Mode the system uses either the LXT or LIRC low speed system oscillator. To switch
back to the NORMAL Mode, where the high speed system oscillator is used, the HLCLK bit should
be set to “1” or HLCLK bit is “0”, but CKS2~CKS0 is set to “010”, “011”, “100”, “101”, “110”
or “111”. As a certain amount of time will be required for the high frequency clock to stabilise,
the status of the HTO bit is checked. The amount of time required for high speed system oscillator
stabilization depends upon which high speed system oscillator type is used.
  
     ­          ­   € ‚      ­   € ‚      ­   Rev. 1.00
50
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Entering the SLEEP0 Mode
There is only one way for the devices to enter the SLEEP0 Mode and that is to execute the "HALT"
instruction in the application program with the IDLEN bit in SMOD register equal to “0” and the
WDT and LVD both off. When this instruction is executed under the conditions described above, the
following will occur:
• The system clock, WDT clock and Time Base clock will be stopped and the application program
will stop at the “HALT” instruction.
• The Data Memory contents and registers will maintain their present condition.
• The WDT will be cleared and stopped no matter if the WDT clock source originates from the fSUB
clock or from the system clock.
• The I/O ports will maintain their present conditions.
• In the status register, the Power Down flag, PDF, will be set and the Watchdog time-out flag, TO,
will be cleared.
Entering the SLEEP1 Mode
There is only one way for the devices to enter the SLEEP1 Mode and that is to execute the “HALT”
instruction in the application program with the IDLEN bit in SMOD register equal to “0” and the
WDT or LVD on. When this instruction is executed under the conditions described above, the
following will occur:
• The system clock and Time Base clock will be stopped and the application program will stop at
the “HALT” instruction, but the WDT or LVD will remain with the clock source coming from the
fSUB clock.
• The Data Memory contents and registers will maintain their present condition.
• The WDT will be cleared and resume counting if the WDT clock source is selected to come from
the fSUB clock as the WDT is enabled.
• The I/O ports will maintain their present conditions.
• In the status register, the Power Down flag, PDF, will be set and the Watchdog time-out flag, TO,
will be cleared.
Entering the IDLE0 Mode
There is only one way for the devices to enter the IDLE0 Mode and that is to execute the “HALT”
instruction in the application program with the IDLEN bit in SMOD register equal to “1” and the
FSYSON bit in WDTC register equal to “0”. When this instruction is executed under the conditions
described above, the following will occur:
• The system clock will be stopped and the application program will stop at the “HALT” instruction,
but the Time Base clock and fSUB clock will be on.
• The Data Memory contents and registers will maintain their present condition.
• The WDT will be cleared and resume counting if the WDT clock source is selected to come from
the fSUB clock and the WDT is enabled. The WDT will stop if its clock source originates from the
system clock.
• The I/O ports will maintain their present conditions.
• In the status register, the Power Down flag, PDF, will be set and the Watchdog time-out flag, TO,
will be cleared.
Rev. 1.00
51
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Entering the IDLE1 Mode
There is only one way for the devices to enter the IDLE1 Mode and that is to execute the “HALT”
instruction in the application program with the IDLEN bit in SMOD register equal to “1” and the
FSYSON bit in WDTC register equal to “1”. When this instruction is executed under the with
conditions described above, the following will occur:
• The system clock and Time Base clock and fSUB clock will be on and the application program will
stop at the “HALT” instruction.
• The Data Memory contents and registers will maintain their present condition.
• The WDT will be cleared and resume counting if the WDT is enabled regardless of the WDT
clock source which originates from the fSUB clock or from the system clock.
• The I/O ports will maintain their present conditions.
• In the status register, the Power Down flag, PDF, will be set and the Watchdog time-out flag, TO,
will be cleared.
Standby Current Considerations
As the main reason for entering the SLEEP or IDLE Mode is to keep the current consumption of
the devices to as low a value as possible, perhaps only in the order of several micro-amps except
in the IDLE1 Mode, there are other considerations which must also be taken into account by the
circuit designer if the power consumption is to be minimised. Special attention must be made to
the I/O pins on the devices. All high-impedance input pins must be connected to either a fixed
high or low level as any floating input pins could create internal oscillations and result in increased
current consumption. This also applies to devices which has different package types, as there may
be unbonbed pins. These must either be setup as outputs or if setup as inputs must have pull-high
resistors connected.
Care must also be taken with the loads, which are connected to I/O pins, which are setup as outputs.
These should be placed in a condition in which minimum current is drawn or connected only to
external circuits that do not draw current, such as other CMOS inputs. Also note that additional
standby current will also be required if the configuration options have enabled the LXT or LIRC
oscillator.
In the IDLE1 Mode the system oscillator is on, if the system oscillator is from the high speed system
oscillator, the additional standby current will also be perhaps in the order of several hundred microamps.
Rev. 1.00
52
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Wake-up
After the system enters the SLEEP or IDLE Mode, it can be woken up from one of various sources
listed as follows:
• An external reset
• An external falling edge on Port A
• A system interrupt
• A WDT overflow
If the system is woken up by an external reset, the devices will experience a full system reset,
however, if the devices are woken up by a WDT overflow, a Watchdog Timer reset will be initiated.
Although both of these wake-up methods will initiate a reset operation, the actual source of the
wake-up can be determined by examining the TO and PDF flags. The PDF flag is cleared by a
system power-up or executing the clear Watchdog Timer instructions and is set when executing the
“HALT” instruction. The TO flag is set if a WDT time-out occurs, and causes a wake-up that only
resets the Program Counter and Stack Pointer, the other flags remain in their original status.
Each pin on Port A can be setup using the PAWU register to permit a negative transition on the pin
to wake-up the system. When a Port A pin wake-up occurs, the program will resume execution at
the instruction following the “HALT” instruction. If the system is woken up by an interrupt, then
two possible situations may occur. The first is where the related interrupt is disabled or the interrupt
is enabled but the stack is full, in which case the program will resume execution at the instruction
following the “HALT” instruction. In this situation, the interrupt which woke-up the devices will not
be immediately serviced, but will rather be serviced later when the related interrupt is finally enabled
or when a stack level becomes free. The other situation is where the related interrupt is enabled and
the stack is not full, in which case the regular interrupt response takes place. If an interrupt request
flag is set high before entering the SLEEP or IDLE Mode, the wake-up function of the related
interrupt will be disabled.
Programming Considerations
The HXT and LXT oscillators both use the same SST counter. For example, if the system is woken
up from the SLEEP0 Mode and both the HXT and LXT oscillators need to start-up from an off state.
The LXT oscillator uses the SST counter after HXT oscillator has finished its SST period.
• If the devices are woken up from the SLEEP0 Mode to the NORMAL Mode, the high speed system
oscillator needs an SST period. The devices will execute first instruction after HTO is “1”. At this
time, the LXT oscillator may not be stability if fSUB is from LXT oscillator. The same situation occurs
in the power-on state. The LXT oscillator is not ready yet when the first instruction is executed.
• If the devices are woken up from the SLEEP1 Mode to NORMAL Mode, and the system clock
source is from HXT oscillator and FSTEN is “1”, the system clock can be switched to the LXT or
LIRC oscillator after wake up.
• There are peripheral functions, such as WDT, TMs and SIM, for which the fSYS is used. If the system
clock source is switched from fH to fL, the clock source to the peripheral functions mentioned above
will change accordingly.
• The on/off condition of fSUB and fS depends upon whether the WDT is enabled or disabled as the
WDT clock source is selected from fSUB.
Rev. 1.00
53
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Watchdog Timer
The Watchdog Timer is provided to prevent program malfunctions or sequences from jumping to
unknown locations, due to certain uncontrollable external events such as electrical noise.
Watchdog Timer Clock Source
The Watchdog Timer clock source is provided by the internal clock, fS, which is in turn supplied by
one of two sources selected by configuration option: fSUB or fSYS/4. The fSUB clock can be sourced
from either the LXT or LIRC oscillators, again chosen via a configuration option. The Watchdog
Timer source clock is then subdivided by a ratio of 213 to 220 to give longer timeouts, the actual value
being chosen using the WS2~WS0 bits in the WDTC register. The LIRC internal oscillator has an
approximate period of 32kHz at a supply voltage of 5V.
However, it should be noted that this specified internal clock period can vary with VDD, temperature
and process variations. The LXT oscillator is supplied by an external 32.768kHz crystal. The other
Watchdog Timer clock source option is the fSYS/4 clock. The Watchdog Timer clock source can
originate from its own internal LIRC oscillator, the LXT oscillator or fSYS/4. It is divided by a value
of 213 to 220, using the WS2~WS0 bits in the WDTC register to obtain the required Watchdog Timer
time-out period.
Watchdog Timer Control Register
A single register, WDTC, controls the required timeout period as well as the enable/disable
operation. This register together with several configuration options control the overall operation of
the Watchdog Timer.
WDTC Register
Rev. 1.00
Bit
7
6
5
4
Name
FSYSON
WS2
WS1
WS0
3
2
1
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
1
1
1
1
0
1
0
WDTEN3 WDTEN2 WDTEN1 WDTEN0
Bit 7
FSYSON: fSYS Control in IDLE Mode
0: Disable
1: Enable
Bit 6 ~ 4
WS2, WS1, WS0: WDT time-out period selection
000: 213/fS
001: 214/fS
010: 215/fS
011: 216/fS
100: 217/fS
101: 218/fS
110: 219/fS
111: 220/fS
These three bits determine the division ratio of the Watchdog Timer source clock,
which in turn determines the timeout period.
Bit 3 ~ 0
WDTEN3, WDTEN2, WDTEN1, WDTEN0: WDT Software Control
1010: Disable
Other: Enable
54
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Watchdog Timer Operation
The Watchdog Timer operates by providing devices reset when their timer overflows. This means
that in the application program and during normal operation the user has to strategically clear the
Watchdog Timer before it overflows to prevent the Watchdog Timer from executing a reset. This is
done using the clear watchdog instructions. If the program malfunctions for whatever reason, jumps
to an unkown location, or enters an endless loop, these clear instructions will not be executed in the
correct manner, in which case the Watchdog Timer will overflow and reset the devices. Some of the
Watchdog Timer options, such as enable/disable, clock source selection and clear instruction type
are selected using configuration options. In addition to a configuration option to enable/disable the
Watchdog Timer, there are also four bits, WDTEN3~WDTEN0, in the WDTC register to offer an
additional enable/disable control of the Watchdog Timer. To disable the Watchdog Timer, as well
as the configuration option being set to disable, the WDTEN3~WDTEN0 bits must also be set to
a specific value of “1010”. Any other values for these bits will keep the Watchdog Timer enabled,
irrespective of the configuration enable/disable setting. After power on these bits will have the
value of “1010”. If the Watchdog Timer is used it is recommended that they are set to a value of
“0101” for maximum noise immunity. Note that if the Watchdog Timer has been disabled, then any
instruction relating to its operation will result in no operation.
WDT Configuration Option
WDTEN3~WDTEN0 Bits
WDT
Enable
WDT Enable
xxxx
WDT Disable
Except 1010
Enable
WDT Disable
1010
Disable
Watchdog Timer Enable/Disable Control
Under normal program operation, a Watchdog Timer time-out will initialise devices reset and set
the status bit TO. However, if the system is in the SLEEP or IDLE Mode, when a Watchdog Timer
time-out occurs, the TO bit in the status register will be set and only the Program Counter and Stack
Pointer will be reset. Three methods can be adopted to clear the contents of the Watchdog Timer.
The first is an external hardware reset, which means a low level on the RES pin, the second is using
the Watchdog Timer software clear instructions and the third is via a HALT instruction.
There are two methods of using software instructions to clear the Watchdog Timer, one of which
must be chosen by configuration option. The first option is to use the single “CLR WDT” instruction
while the second is to use the two commands “CLR WDT1” and “CLR WDT2”. For the first option,
a simple execution of “CLR WDT” will clear the WDT while for the second option, both “CLR
WDT1” and “CLR WDT2” must both be executed alternately to successfully clear the Watchdog
Timer. Note that for this second option, if “CLR WDT1” is used to clear the Watchdog Timer,
successive executions of this instruction will have no effect, only the execution of a “CLR WDT2”
instruction will clear the Watchdog Timer. Similarly after the “CLR WDT2” instruction has been
executed, only a successive “CLR WDT1” instruction can clear the Watchdog Timer.
The maximum time out period is when the 220 division ratio is selected. As an example, with a
32.768kHz LXT oscillator as its source clock, this will give a maximum watchdog period of around
32 seconds for the 220 division ratio, and a minimum timeout of 250ms for the 213 division ration. If
the fSYS/4 clock is used as the Watchdog Timer clock source, it should be noted that when the system
enters the SLEEP or IDLE0 Mode, then the instruction clock is stopped and the Watchdog Timer
may lose its protecting purposes. For systems that operate in noisy environments, using the fSUB
clock source is strongly recommended.
Rev. 1.00
55
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
 € ‚ ƒ  € ‚ ƒ „ €  
€ „‚ 

   ­  

† ‡




­  
 € ‚ 
  
­  Reset and Initialisation
A reset function is a fundamental part of any microcontroller ensuring that the devices can be set
to some predetermined condition irrespective of outside parameters. The most important reset
condition is after power is first applied to the microcontroller. In this case, internal circuitry will
ensure that the microcontroller, after a short delay, will be in a well defined state and ready to
execute the first program instruction. After this power-on reset, certain important internal registers
will be set to defined states before the program commences. One of these registers is the Program
Counter, which will be reset to zero forcing the microcontroller to begin program execution from the
lowest Program Memory address.
In addition to the power-on reset, situations may arise where it is necessary to forcefully apply
a reset condition when the microcontroller is running. One example of this is where after power
has been applied and the microcontroller is already running, the RES line is forcefully pulled low.
In such a case, known as a normal operation reset, some of the microcontroller registers remain
unchanged allowing the microcontroller to proceed with normal operation after the reset line is
allowed to return high.
Another type of reset is when the Watchdog Timer overflows and resets the microcontroller. All
types of reset operations result in different register conditions being setup. Another reset exists in
the form of a Low Voltage Reset, LVR, where a full reset, similar to the RES reset is implemented in
situations where the power supply voltage falls below a certain threshold.
Reset Functions
There are five ways in which a microcontroller reset can occur, through events occurring both
internally and externally:
Power-on Reset
The most fundamental and unavoidable reset is the one that occurs after power is first applied to
the microcontroller. As well as ensuring that the Program Memory begins execution from the first
memory address, a power-on reset also ensures that certain other registers are preset to known
conditions. All the I/O port and port control registers will power up in a high condition ensuring that
all pins will be first set to inputs.
Note: tRSTD is power-on delay, typical time=100ms
Power-On Reset Timing Chart
Rev. 1.00
56
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
RES Pin
As the reset pin is shared with PB.6, the reset function must be selected using a configuration
option. Although the microcontroller has an internal RC reset function, if the VDD power supply
rise time is not fast enough or does not stabilise quickly at power-on, the internal reset function
may be incapable of providing proper reset operation. For this reason it is recommended that an
external RC network is connected to the RES pin, whose additional time delay will ensure that the
RES pin remains low for an extended period to allow the power supply to stabilise. During this time
delay, normal operation of the microcontroller will be inhibited. After the RES line reaches a certain
voltage value, the reset delay time tRSTD is invoked to provide an extra delay time after which the
microcontroller will begin normal operation. The abbreviation SST in the figures stands for System
Start-up Timer.
For most applications a resistor connected between VDD and the RES pin and a capacitor connected
between VSS and the RES pin will provide a suitable external reset circuit. Any wiring connected to
the RES pin should be kept as short as possible to minimise any stray noise interference.
For applications that operate within an environment where more noise is present the Enhanced Reset
Circuit shown is recommended.
Note: “*” It is recommended that this component is added for added ESD protection.
“**” It is recommended that this component is added in environments where power line
noise is significant.
External RES Circuit
More information regarding external reset circuits is located in Application Note HA0075E on the
Holtek website.
Pulling the RES Pin low using external hardware will also execute devices reset. In this case, as in
the case of other resets, the Program Counter will reset to zero and program execution initiated from
this point.
RES Reset Timing Chart
Rev. 1.00
57
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Low Voltage Reset – LVR
The microcontroller contains a low voltage reset circuit in order to monitor the supply voltage of the
devices, which is selected via a configuration option. If the supply voltage of the devices drop to within a
range of 0.9V~VLVR such as might occur when changing the battery, the LVR will automatically reset the
devices internally. The LVR includes the following specifications: For a valid LVR signal, a low voltage,
i.e., a voltage in the range between 0.9V~VLVR must exist for greater than the value tLVR specified in the A.C.
characteristics. If the low voltage state does not exceed tLVR, the LVR will ignore it and will not perform a
reset function. One of a range of specified voltage values for VLVR can be selected using configuration
options.
Note: tRSTD is power-on delay, typical time=100ms
Low Voltage Reset Timing Chart
Watchdog Time-out Reset during Normal Operation
The Watchdog time-out Reset during normal operation is the same as a hardware RES pin reset
except that the Watchdog time-out flag TO will be set to “1”.
Note: tRSTD is power-on delay, typical time=100ms
WDT Time-out Reset during Normal Operation Timing Chart
Watchdog Time-out Reset during SLEEP or IDLE Mode
The Watchdog time-out Reset during SLEEP or IDLE Mode is a little different from other kinds
of reset. Most of the conditions remain unchanged except that the Program Counter and the Stack
Pointer will be cleared to “0” and the TO flag will be set to “1”. Refer to the A.C. Characteristics for
tSST details.
Note: The tSST is 15~16 clock cycles if the system clock source is provided by EC, HIRC.
The tSST is 1024 clock for HXT or LXT.
The tSST is 1~2 clock for LIRC.
WDT Time-out Reset during Idle/Sleep Timing Chart
Rev. 1.00
58
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Reset Initial Conditions
The different types of reset described affect the reset flags in different ways. These flags, known
as PDF and TO are located in the status register and are controlled by various microcontroller
operations, such as the SLEEP or IDLE Mode function or Watchdog Timer. The reset flags are
shown in the table:
TO
PDF
0
0
Power-on reset
RESET Conditions
u
u
RES or LVR reset during NORMAL or SLOW Mode operation
1
u
WDT time-out reset during NORMAL or SLOW Mode operation
1
1
WDT time-out reset during IDLE or SLEEP Mode operation
Note: “u” stands for unchanged
The following table indicates the way in which the various components of the microcontroller are
affected after a power-on reset occurs.
Item
Condition After RESET
Program Counter
Reset to zero
Interrupts
All interrupts will be disabled
WDT
Clear after reset, WDT begins counting
Timer/Event Counter
Timer Counter will be turned off
Input/Output Ports
I/O ports will be setup as inputs
Stack Pointer
Stack Pointer will point to the top of the stack
The different kinds of resets all affect the internal registers of the microcontroller in different ways.
To ensure reliable continuation of normal program execution after a reset occurs, it is important to
know what condition the microcontroller is in after a particular reset occurs. The following table
describes how each type of reset affects each of the microcontroller internal registers. Note that
where more than one package type exists the table will reflect the situation for the larger package
type.
Rev. 1.00
59
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
HT45FH23A
HT45FH24A
Power-on Reset
PCL
●
●
0000 0000
0000 0000
0000 0000
0000 0000
MP0
●
●
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
MP1
●
●
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
BP
●
●
- - - - - - - 0
- - - - - - - 0
- - - - - - - 0
- - - - - - - u
ACC
●
●
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLP
●
●
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLH
●
- xxx xxxx
- uuu uuuu
- uuu uuuu
- uuu uuuu
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
- - - - - xxx
- - - - - uuu
- - - - - uuu
- - - - - uuu
Register
TBLH
TBHP
●
●
TBHP
RES or LVR Reset
WDT Time-out
(Normal Operation)
WDT Time-out
(Idle/Sleep)
●
- - - - xxxx
- - - - uuuu
- - - - uuuu
- - - - uuuu
STATUS
●
●
- - 00 xxxx
- - uu uuuu
- - 1u uuuu
- - 11 u u u u
SMOD
●
●
0 0 0 0 0 0 11
0 0 0 0 0 0 11
0 0 0 0 0 0 11
uuuu uuuu
LVDC
●
●
- - 00 - 000
- - 00 - 000
- - 00 - 000
- -uu - uuu
INTEDGE
●
●
- - - - 0000
- - - - 0000
- - - - 0000
- - - - uuuu
WDTC
●
●
0 111 1 0 1 0
0 111 1 0 1 0
0 111 1 0 1 0
uuuu uuuu
INTC0
●
●
- 000 0000
- 000 0000
- 000 0000
- uuu uuuu
INTC1
●
●
- 000 - 000
- 000 - 000
- 000 - 000
- uuu - uuu
MFIC0
●
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
MFIC1
●
●
- 000 - 000
- 000 - 000
- 000 - 000
- uuu - uuu
PA
●
●
1111 1111
1111 1111
1111 1111
uuuu uuuu
PAC
●
●
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
●
- 111 1111
- 111 1111
- 111 1111
- uuu uuuu
1111 1111
1111 1111
1111 1111
uuuu uuuu
- 111 1111
- 111 1111
- 111 1111
- uuu uuuu
1111 1111
1111 1111
1111 1111
uuuu uuuu
- 111 1111
- 111 1111
- 111 1111
- uuu uuuu
1111 1111
1111 1111
1111 1111
uuuu uuuu
- 111 1111
- 111 1111
- 111 1111
- uuu uuuu
PB
PBC
●
●
PBC
PC
●
●
PC
PCC
●
●
PCC
●
1111 1111
1111 1111
1111 1111
uuuu uuuu
PD
●
- - - - - - 11
- - - - - - 11
- - - - - - 11
- - - - - -uu
PDC
●
- - - - - - 11
- - - - - - 11
- - - - - - 11
- - - - - -uu
PAWU
●
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
PAPU
●
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
PBPU
●
- 000 0000
- 000 0000
- 000 0000
- uuu uuuu
0000 0000
0000 0000
0000 0000
uuuu uuuu
- 000 0000
- 000 0000
- 000 0000
- uuu uuuu
PBPU
PCPU
●
●
PCPU
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
PDPU
●
- - - - - -00
- - - - - -00
- - - - - -00
- - - - - -uu
PWM0
●
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
PWM1
●
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
MISC
●
●
0000 - - 00
0000 - - 00
0000 - - 00
uuuu - - uu
ADPCR
●
- -00 0000
- -00 0000
- -00 0000
- -uu uuuu
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
ADPCR
ADRL
●
●
xxxx - - - -
xxxx - - - -
xxxx - - - -
uuuu - - - -
ADRH
●
●
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
Rev. 1.00
60
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
HT45FH24A
ADCR
HT45FH23A
Register
●
ADCR
Power-on Reset
RES or LVR Reset
WDT Time-out
(Normal Operation)
WDT Time-out
(Idle/Sleep)
01 - - -000
01 - - -000
01 - - -000
uu - - -uuu
●
01 - - 0000
01 - - 0000
01 - - 0000
uu - - uuuu
ACSR
●
●
100 - - 000
100 - - 000
100 - - 000
uuu - - uuu
SIMC0
●
●
111 0 0 0 0 -
111 0 0 0 0 -
111 0 0 0 0 -
uuuu uuuu
SIMC1
●
●
1000 0001
1000 0001
1000 0001
uuuu uuuu
SIMD
●
●
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
SIMA/SIMC2
●
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
TMR0
●
●
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMR0C
●
●
00- 0 1000
00- 0 1000
00- 0 1000
uu- u uuuu
TMR1L
●
●
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMR1H
●
●
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
TMR1C
●
●
0000 1- - -
0000 1- - -
0000 1- - -
uuuu u- - -
EEA
●
●
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
EED
●
●
xxxx xxxx
xxxx xxxx
xxxx xxxx
uuuu uuuu
EEC
●
●
- - - - 0000
- - - - 0000
- - - - 0000
- - - - uuuu
LCDC
●
●
- 000 0000
- 000 0000
- 000 0000
- uuu uuuu
LDOC
●
●
- - -0 0000
- - -0 0000
- - -0 0000
- - -u uuuu
DACTRL
●
●
000 - - - -0
000 - - - -0
000 - - - -0
uuu - - - -u
DAL
●
●
0000 - - - -
0000 - - - -
0000 - - - -
uuuu - - - -
DAH
●
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
CMP1C0
●
●
0001 0000
0001 0000
0001 0000
uuuu uuuu
CMP1C1
●
●
1- - - 0010
1- - - 0010
1- - - 0010
1- - - uuuu
CMP2C0
●
●
0001 0000
0001 0000
0001 0000
uuuu uuuu
CMP2C1
●
●
00 - - 0010
00 - - 0010
00 - - 0010
uu- - uuuu
OPA1C0
●
●
0- - - - - - -
0- - - - - - -
0- - - - - - -
u- - - - - - -
OPA1C1
●
●
0 0 0 0 11 0 0
0 0 0 0 11 0 0
0 0 0 0 11 0 0
uuuu uuuu
OPA2C0
●
●
0- - - - - - -
0- - - - - - -
0- - - - - - -
u- - - - - - -
OPA2C1
●
●
0 0 0 0 11 0 0
0 0 0 0 11 0 0
0 0 0 0 11 0 0
uuuu uuuu
OPA2C2
●
●
00 - - 0000
00 - - 0000
00 - - 0000
uu - - uuuu
TBC
●
●
0 0 11 0 111
0 0 11 0 111
0 0 11 0 111
uuuu uuuu
BPCTL
●
●
0000 0000
0000 0000
0000 0000
uuuu uuuu
Note: “-“ not implemented
“u” means “unchanged”
“x” means “unknown”
Rev. 1.00
61
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Input/Output Ports
Holtek microcontrollers offer considerable flexibility on their I/O ports. With the input or output
designation of every pin fully under user program control, pull-high selections for all ports and
wake-up selections on certain pins, the user is provided with an I/O structure to meet the needs of a
wide range of application possibilities.
The devices provide bidirectional input/output lines labeled with port names PA~PD. These I/O
ports are mapped to the RAM Data Memory with specific addresses as shown in the Special Purpose
Data Memory table. All of these I/O ports can be used for input and output operations. For input
operation, these ports are non-latching, which means the inputs must be ready at the T2 rising edge
of instruction “MOV A, [m]”, where m denotes the port address. For output operation, all the data is
latched and remains unchanged until the output latch is rewritten.
Pull-high Resistors
Many product applications require pull-high resistors for their switch inputs usually requiring the
use of an external resistor. To eliminate the need for these external resistors, when configured as
an input have the capability of being connected to an internal pull-high resistor. These pull-high
resistors are selectable via a register known as PAPU, PBPU, PCPU and PDPU located in the Data
Memory. The pull-high resistors are implemented using weak PMOS transistors.
Port A Wake-up
The HALT instruction forces the microcontroller into the SLEEP or IDLE Mode which preserves
power, a feature that is important for battery and other low-power applications. Various methods
exist to wake-up the microcontroller, one of which is to change the logic condition on one of the Port
A pins from high to low. This function is especially suitable for applications that can be woken up
via external switches. Each pin on Port A can be selected individually to have this wake-up feature
using the PAWU register.
I/O Port Control Registers
Each I/O port has its own control register known as PAC~PDC, to control the input/output
configuration. With this control register, each CMOS output or input can be reconfigured
dynamically under software control. Each pin of the I/O ports is directly mapped to a bit in its
associated port control register. For the I/O pin to function as an input, the corresponding bit of the
control register must be written as a a “1”. This will then allow the logic state of the input pin to be
directly read by instructions. When the corresponding bit of the control register is written as a “0”,
the I/O pin will be setup as a CMOS output. If the pin is currently setup as an output, instructions
can still be used to read the output register.
However, it should be noted that the program will in fact only read the status of the output data latch
and not the actual logic status of the output pin.
Rev. 1.00
62
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
PAWU, PAPU, PA, PAC, PBPU, PB, PBC, PCPU, PC, PCC, PD, PDC Registers
• HT45FH23A
Register
Name
PAWU
PAPU
PA
PAC
PBPU
PB
PBC
PCPU
PC
PCC
Bit
7
PAWU7
PAPU7
PA7
PAC7
—
—
—
—
—
—
6
PAWU6
PAPU6
PA6
PAC6
PBPU6
PB6
PBC6
PCPU6
PC6
PCC6
5
PAWU5
PAPU5
PA5
PAC5
PBPU5
PB5
PBC5
PCPU5
PC5
PCC5
4
PAWU4
PAPU4
PA4
PAC4
PBPU4
PB4
PBC4
PCPU4
PC4
PCC4
3
PAWU3
PAPU3
PA3
PAC3
PBPU3
PB3
PBC3
PCPU3
PC3
PCC3
2
PAWU2
PAPU2
PA2
PAC2
PBPU2
PB2
PBC2
PCPU2
PC2
PCC2
1
PAWU1
PAPU1
PA1
PAC1
PBPU1
PB1
PBC1
PCPU1
PC1
PCC1
0
PAWU0
PAPU0
PA0
PAC0
PBPU0
PB0
PBC0
PCPU0
PC0
PCC0
“—”: Unimplemented, read as “0”
PAWUn: PA wake-up function enable
0: disable
1: enable
PAPUn/PBPUn/PCPUn: Pull-high function enable
0: disable
1: enable
PACn/PBCn/PCCn: I/O type selection
0: output
1: input
Note: The HT45FH23A I/O lines, as the PB0~PB5 and PC4~PC6 are not connected to the external
pins, it is recommended to set these pins as I/O input with pull-high resistor, or as I/O output
high or output low via the related I/O port control bits.
• HT45FH24A
Bit
Register
Name
7
6
5
4
3
2
1
0
PAWU
PAPU
PA
PAC
PBPU
PB
PBC
PCPU
PC
PCC
PDPU
PD
PDC
PAWU7
PAPU7
PA7
PAC7
PBPU7
PB7
PBC7
PCPU7
PC7
PCC7
—
—
—
PAWU6
PAPU6
PA6
PAC6
PBPU6
PB6
PBC6
PCPU6
PC6
PCC6
—
—
—
PAWU5
PAPU5
PA5
PAC5
PBPU5
PB5
PBC5
PCPU5
PC5
PCC5
—
—
—
PAWU4
PAPU4
PA4
PAC4
PBPU4
PB4
PBC4
PCPU4
PC4
PCC4
—
—
—
PAWU3
PAPU3
PA3
PAC3
PBPU3
PB3
PBC3
PCPU3
PC3
PCC3
—
—
—
PAWU2
PAPU2
PA2
PAC2
PBPU2
PB2
PBC2
PCPU2
PC2
PCC2
—
—
—
PAWU1
PAPU1
PA1
PAC1
PBPU1
PB1
PBC1
PCPU1
PC1
PCC1
PDPU1
PD1
PDC1
PAWU0
PAPU0
PA0
PAC0
PBPU0
PB0
PBC0
PCPU0
PC0
PCC0
PDPU0
PD0
PDC0
“—”: Unimplemented, read as “0”
PAWUn: PA wake-up function enable
0: disable
1: enable
PAPUn/PBPUn/PCPUn/PDPUn: Pull-high function enable
0: disable
1: enable
Rev. 1.00
63
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
PACn/PBCn/PCCn/PDCn: I/O type selection
0: output
1: input
Note: As the PB0~PB5, PB7, PC4~PC7 and PD0~PD1 are not connected to the external pins, it is
recommended to set these pins as I/O input with pull-high resistor, or as I/O output high or
output low via the related I/O port control bits.
Port B NMOS Open Drain Control Register
Port B pins PB0~PB3 can be setup as open drain structures. This is implemented using the
ODE0~ODE3 bits in the MISC register.
• MISC Register
Bit
7
6
5
4
3
2
1
0
Name
ODE3
ODE2
ODE1
ODE0
—
—
PFDSEL
PFDEN
R/W
R/W
R/W
R/W
R/W
—
—
R/W
R/W
POR
0
0
0
0
—
—
0
0
Bit 7
ODE3: PB3 Open Drain Control
0: disable
1: enable
Bit 6
ODE2: PB2 Open Drain Control
0: disable
1: enable
Bit 5
ODE1: PB1 Open Drain Control
0: disable
1: enable
Bit 4
ODE0: PB0 Open Drain Control
0: disable
1: enable
Bit 3~2
Unimplemented, read as “0”
Bit 1~0
PFDSEL, PFDEN: PFD related control – described elsewhere
The PB0~PB3 are not connected to the external pins.
I/O Pin Structures
The accompanying diagram illustrates the internal structures of some generic I/O pin types. As
the exact logical construction of the I/O pin will differ from these drawings, they are supplied as a
guide only to assist with the functional understanding of the I/O pins. The wide range of pin-shared
structures does not permit all types to be shown.
Programming Considerations
Within the user program, one of the first things to consider is port initialisation. After a reset, all of
the I/O data and port control registers will be set high. This means that all I/O pins will default to
an input state, the level of which depends on the other connected circuitry and whether pull-high
selections have been chosen. If the port control registers, PAC~PDC, are then programmed to setup
some pins as outputs, these output pins will have an initial high output value unless the associated
port data registers, PA~PD, are first programmed. Selecting which pins are inputs and which are
outputs can be achieved byte-wide by loading the correct values into the appropriate port control
register or by programming individual bits in the port control register using the “SET[m].i” and
“CLR[m].i” instructions. Note that when using these bit control instructions, a read-modify-write
operation takes place. The microcontroller must first read in the data on the entire port, modify it to
the required new bit values and then rewrite this data back to the output ports.
Rev. 1.00
64
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Note that when the device is powered on the PC1/AN5/OSC1 and PC0/AN4/OSC2 pins will
experience a high level output between 1 and 2 volts for a period of tRSTD. It is important to take this
into account for any connected external hardware devices.
Read Modify Write Timing
Port A has the additional capability of providing wake-up functions. When the devices are in the
SLEEP or IDLE Mode, various methods are available to wake the devices up. One of these is a high
to low transition of any of the Port A pins. Single or multiple pins on Port A can be setup to have this
function. In addition, the Port B pins also provide Open Drain I/O structure options which can be
controlled by the specific register.
Š ‚   ˆ’  

 

€ ‹  € Ž  € ‘  ‘  Ž
    „
 ƒ † ‡ ˆ ‰ €





­
 „ ­
­
„ ­
Š € ‹ Œ
€ ‚
€ „
€
ƒ
ƒ
ƒ
ƒ
‡ ˆ Generic Input/Output Ports
Rev. 1.00
65
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Timer/Event Counters
The provision of timers form an important part of any microcontroller, giving the designer a means
of carrying out time related functions. The devices contain one 8-bit and one 16-bit count-up timer
respectively. As each timer has four different operating modes, they can be configured to operate
as a general timer, an external event counter, an internal event counter for comparator, or as a pulse
width measurement device. The provision of a prescaler to the clock circuitry of the 8-bit Timer/
Event Counter also gives added range to this timer.
There are two types of registers related to the Timer/Event Counters. The first are the registers
that contain the actual value of the Timer/Event Counter and into which an initial value can be
preloaded. Reading from these registers retrieves the contents of the Timer/Event Counter. The
second type of associated register is the Timer Control Register which defines the timer options and
determines how the Timer/Event Counter is to be used. The Timer/Event Counters can have the their
clock configured to come from an internal clock source. In addition, their clock source can also be
configured to come from an external timer pin.
Configuring the Timer/Event Counter Input Clock Source
The internal timer’s clock can originate from various sources. The system clock source is used when
the Timer/Event Counter is in the timer mode or in the pulse width measurement mode. For Timer/
Event Counter 0 this internal clock source is fSYS which is also divided by a prescaler, the division
ratio of which is conditioned by the Timer Control Register, TMR0C, bits T0PSC0~ T0PSC2. For
Timer/Event Counter 1 this internal clock source can be chosen from a combination of internal
clocks using a configuration option and the T1S bit in the TMR1C register.
An external clock source is used when the timer is in the event counting mode, the clock source
being provided on an external timer pin TC0 or TC1, depending upon which timer is used.
Depending upon the condition of the T0E or T1E bit, each high to low, or low to high transition on
the external timer pin will increment the counter by one.
Timer Registers – TMR0, TMR1L, TMR1H
The timer registers are special function registers located in the Special Purpose Data Memory and
is the place where the actual timer value is stored. For the 8-bit Timer/Event Counter 0, this register
is known as TMR0. For 16-bit Timer/Event Counter 1, the timer registers are known as TMR1L
and TMR1H. The value in the timer registers increases by one each time an internal clock pulse is
received or an external transition occurs on the external timer pin. The timer will count from the
initial value loaded by the preload register to the full count of FFH for the 8-bit timer or FFFFH for
the 16-bit timer at which point the timer overflows and an internal interrupt signal is generated. The
timer value will then be reset with the initial preload register value and continue counting.
To achieve a maximum full range count of FFH for the 8-bit timer or FFFFH for the 16-bit timer,
the preload registers must first be cleared to all zeros. It should be noted that after power-on, the
preload register will be in an unknown condition. Note that if the Timer/Event Counter is switched
off and data is written to its preload registers, this data will be immediately written into the actual
timer registers. However, if the Timer/Event Counter is enabled and counting, any new data written
into the preload data registers during this period will remain in the preload registers and will only be
written into the timer registers the next time an overflow occurs.
Rev. 1.00
66
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
­    „
 €‚ ‚ ­ ‚ ‚  ƒ
  ‚
  
†  ‚ †
   8-bit Timer/Event Counter 0 Structure
„ ­

 ƒ
„ ‚
‚ ƒ  ‚
 ­
 
  ­ ƒ
­
†
‚
„ ƒ
­ „ ­ €
   ­  
  
„
  16-bit Timer/Event Counter 1 Structure
Note:1. The PFD clock source, PFD0 or PFD1, which is from Timer0 or Timer1, is selected by
PFDSEL bit in MISC register.
2. The output is controlled by PA5 data.
3. CMP1X is comparator 1 output.
4. CMP2X is comparator 2 output.
For the 16-bit Timer/Event Counter which has both low byte and high byte timer registers, accessing
these registers is carried out in a specific way. It must be noted when using instructions to preload
data into the low byte timer register, namely TMR1L, the data will only be placed in a low byte
buffer and not directly into the low byte timer register. The actual transfer of the data into the low
byte timer register is only carried out when a write to its associated high byte timer register, namely
TMR1H, is executed. On the other hand, using instructions to preload data into the high byte timer
register will result in the data being directly written to the high byte timer register. At the same time
the data in the low byte buffer will be transferred into its associated low byte timer register. For this
reason, the low byte timer register should be written first when preloading data into the 16-bit timer
registers. It must also be noted that to read the contents of the low byte timer register, a read to the
high byte timer register must be executed first to latch the contents of the low byte timer register
into its associated low byte buffer. After this has been done, the low byte timer register can be read
in the normal way. Note that reading the low byte timer register will result in reading the previously
latched contents of the low byte buffer and not the actual contents of the low byte timer register.
Rev. 1.00
67
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Timer Control Registers – TMR0C, TMR1C
The flexible features of the Holtek microcontroller Timer/Event Counters enable them to operate in
four different modes, the options of which are determined by the contents of their respective control
register.
It is the Timer Control Register together with its corresponding timer registers that control the
full operation of the Timer/Event Counters. Before the timers can be used, it is essential that the
appropriate Timer Control Register is fully programmed with the right data to ensure its correct
operation, a process that is normally carried out during program initialisation.
To choose which of the four modes the timer is to operate in, either in the timer mode, the external
event counting mode, the internal event counter mode, or the pulse width measurement mode, bits 7
and 6 of the Timer Control Register, which are known as the bit pair T0M1/T0M0 or T1M1/T1M0
respectively, depending upon which timer is used, must be set to the required logic levels. The timeron bit, which is bit 4 of the Timer Control Register and known as T0ON or T1ON, depending upon
which timer is used, provides the basic on/off control of the respective timer. Setting the bit high
allows the counter to run, clearing the bit stops the counter. For timers that have prescalers, bits 0~2
of the Timer Control Register determine the division ratio of the input clock prescaler. The prescaler
bit settings have no effect if an external clock source is used. If the timer is in the event count or
pulse width measurement mode, the active transition edge level type is selected by the logic level of
bit 3 of the Timer Control Register which is known as T0E or T1E depending upon which timer is
used. An additional T1S bit in the TMR1C register is used to determine the clock source for Timer/
Event Counter 1.
Configuring the Timer Mode
In this mode, the Timer/Event Counter can be utilised to measure fixed time intervals, providing an
internal interrupt signal each time the Timer/Event Counter overflows. To operate in this mode, the
Operating Mode Select bit pair, T0M1/T0M0 or T1M1/T1M0, in the Timer Control Register must be
set to the correct value as shown.Control Register Operating Mode Select Bits for the Timer Mode
Bit7
Bit6
1
0
In this mode the internal clock, fSYS, is used as the internal clock for 8-bit Timer/Event Counter 0
and fSUB or fSYS/4 is used as the internal clock for 16-bit Timer/Event Counter 1. However, the clock
source, fSYS, for 8-bit timer is further divided by a prescaler, the value of which is determined by the
Prescaler Rate Select bits T0PSC2~T0PSC0, which are bits 2~0 in the Timer Control Register. After
the other bits in the Timer Control Register have been setup, the enable bit T0ON or T1ON, which is
bit 4 of the Timer Control Register, can be set high to enable the Timer/Event Counter to run. Each
time an internal clock cycle occurs, the Timer/Event Counter increments by one. When it is full and
overflows, an interrupt signal is generated and the Timer/Event Counter will reload the value already
loaded into the preload register and continue counting. The interrupt can be disabled by ensuring
that the Timer/Event Counter Interrupt Enable bit in the Interrupt Control Register, INTC0, is reset
to zero.
Timer Mode Timing Chart
Rev. 1.00
68
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Configuring the Event Counter Mode
In this mode, a number of internally changing logic events, occurring on the internal comparators
output, can be recorded by the Timer/Event Counter. To operate in this mode, the Operating Mode
Select bit pair, T0M1/T0M0 or T1M1/T1M0, in the Timer Control Register must be set to the correct
value as shown. Control Register Operating Mode Select Bits for the Event Counter Mode
Bit7
Bit6
0
0/1
In this mode, the comparator output, CMP1X or CMP2X, is used as the Timer/Event Counter
clock source, however it is not divided by the internal prescaler. After the other bits in the Timer
Control Register have been setup, the enable bit T0ON or T1ON, which is bit 4 of the Timer Control
Register, can be set high to enable the Timer/Event Counter to run. If the Active Edge Select bit T0E
or T1E, which is bit 3 of the Timer Control Register, is low, the Timer/Event Counter will increment
each time the external timer pin receives a low to high transition. If the Active Edge Select bit is
high, the counter will increment each time the external timer pin receives a high to low transition.
When it is full and overflows, an interrupt signal is generated and the Timer/Event Counter will
reload the value already loaded into the preload register and continue counting. The interrupt can
be disabled by ensuring that the Timer/Event Counter Interrupt Enable bit in the Interrupt Control
Register, INTC0, is reset to zero.
It should be noted that in the internal event counting mode, even if the microcontroller is in the
Power Down Mode, the Timer/Event Counter will continue to record externally changing logic
events on the timer input pin. As a result when the timer overflows it will generate a timer interrupt
and corresponding wake-up source.
Event Counter Mode Timing Chart (TnE=1)
Configuring the Pulse Width Measurement Mode
In this mode, the Timer/Event Counter can be utilised to measure the width of external pulses
applied to the external timer pin. To operate in this mode, the Operating Mode Select bit pair, T0M1/
T0M0 or T1M1/T1M0, in the Timer Control Register must be set to the correct value as shown.
Control Register Operating Mode Select Bits for the Pulse Width Measurement Mode
Bit7
Bit6
1
1
In this mode the internal clock, fSYS, is used as the internal clock for 8-bit Timer/Event Counter 0
and fSUB or fSYS/4 is used as the internal clock for 16-bit Timer/Event Counter 1. However, the clock
source, fSYS, for 8-bit timer is further divided by a prescaler, the value of which is determined by the
Prescaler Rate Select bits T0PSC2~T0PSC0, which are bits 2~0 in the Timer Control Register. After
the other bits in the Timer Control Register have been setup, the enable bit T0ON or T1ON, which
is bit 4 of the Timer Control Register, can be set high to enable the Timer/Event Counter, however it
will not actually start counting until an active edge is received on the external timer pin.
Rev. 1.00
69
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
If the Active Edge Select bit T0E or T1E, which is bit 3 of the Timer Control Register, is low, once a
high to low transition has been received on the external timer pin, TMR0 or TMR1, the Timer/Event
Counter will start counting until the external timer pin returns to its original high level. At this point
the enable bit will be automatically reset to zero and the Timer/Event Counter will stop counting. If
the Active Edge Select bit is high, the Timer/Event Counter will begin counting once a low to high
transition has been received on the external timer pin and stop counting when the external timer pin
returns to its original low level. As before, the enable bit will be automatically reset to zero and the
Timer/Event Counter will stop counting. It is important to note that in the Pulse Width Measurement
Mode, the enable bit is automatically reset to zero when the external control signal on the external
timer pin returns to its original level, whereas in the other two modes the enable bit can only be reset
to zero under program control.
The residual value in the Timer/Event Counter, which can now be read by the program, therefore
represents the length of the pulse received on the external timer pin. As the enable bit has now been
reset, any further transitions on the external timer pin will be ignored. Not until the enable bit is
again set high by the program can the timer begin further pulse width measurements. In this way,
single shot pulse measurements can be easily Made.
It should be noted that in this mode the Timer/Event Counter is controlled by logical transitions
on the external timer pin and not by the logic level. When the Timer/Event Counter is full and
overflows, an interrupt signal is generated and the Timer/Event Counter will reload the value already
loaded into the preload register and continue counting. The interrupt can be disabled by ensuring
that the Timer/Event Counter Interrupt Enable bit in the Interrupt Control Register, INTC0, is reset
to zero.
As the external timer pin is shared with an I/O pin, to ensure that the pin is configured to operate as
a pulse width measurement pin, two things have to happen. The first is to ensure that the Operating
Mode Select bits in the Timer Control Register place the Timer/Event Counter in the Pulse Width
Measurement Mode, the second is to ensure that the port control register configures the pin as an
input.
          Pulse Width Capture Mode Timing Chart (TnE=0)
Rev. 1.00
70
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Programmable Frequency Divider – PFD
The Programmable Frequency Divider provides a means of producing a variable frequency output
suitable for applications requiring a precise frequency generator.
The PFD output is pin-shared with the I/O pin PA5. The PFD function is enabled via PFDEN bit in
MISC register, however, if not enabled, the pin can operate as a normal I/O pin.
The clock source for the PFD circuit can originate from either the timer 0 or timer 1 overflow signal
selected via PFDSELbit in MISC register. The output frequency is controlled by loading the required
values into the timer registers and prescaler registers to give the required division ratio. The timer
will begin to count-up from this preload register value until full, at which point an overflow signal
is generated, causing the PFD output to change state. The timer will then be automatically reloaded
with the preload register value and continue counting-up.
For the PFD output to function, it is essential that the corresponding bit of the Port A control register
PAC bit 5 is setup as an output. If setup as an input the PFD output will not function, however, the
pin can still be used as a normal input pin. The PFD output will only be activated if bit PA5 is set
to “1”. This output data bit is used as the on/off control bit for the PFD output. Note that the PFD
output will be low if the PA5 output data bit is cleared to “0”.
Using this method of frequency generation, and if a crystal oscillator is used for the system clock,
very precise values of frequency can be generated.
PFD Output Control
Prescaler
Bits T0PSC0~T0PSC2 of the TMR0C register can be used to define the pre-scaling stages of the
internal clock sources of the Timer/Event Counter 0. The Timer/Event Counter overflow signal can
be used to generate signals for the PFD and Timer Interrupt.
Rev. 1.00
71
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
TMR0C Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
T0M1
T0M0
—
T0ON
T0E
T0PSC2
T0PSC1
T0PSC0
R/W
R/W
R/W
—
R/W
R/W
R/W
R/W
R/W
POR
0
0
—
0
1
0
0
0
Bit 7~6
T0M1, T0M0: Timer 0 operation mode selection
00: event counter mode, the input signal is from Comparator 1 output
01: event counter mode, the input signal is from TC0 pin
10: timer mode
11: pulse width capture mode
Bit 5
unimplemented, read as “0”
Bit 4
T0ON: Timer/Event Counter counting enable
0: disable
1: enable
Bit 3
T0E:
Event counter active edge selection
0: count on raising edge
1: count on falling edge
Pulse Width Capture active edge selection
0: start counting on falling edge, stop on rasing edge
1: start counting on raising edge, stop on falling edge
Bit 2~0
T0PSC2, T0PSC1, T0PSC0: Timer prescaler rate selection Timer internal clock=
000: fSYS
001: fSYS/2
010: fSYS/4
011: fSYS/8
100: fSYS/16
101: fSYS/32
110: fSYS/64
111: fSYS/128
72
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
TMR1C Register
Bit
7
6
5
4
3
2
1
0
Name
T1M1
T1M0
T1S
T1ON
T1E
—
—
—
R/W
R/W
R/W
R/W
R/W
R/W
—
—
—
POR
0
0
0
0
1
—
—
—
Bit 7~6
T1M1, T1M0: Timer1 operation mode selection
00: event counter mode, the input signal is from Comparator 2 output
01: event counter mode, the input signal is from TC1 pin
10: timer mode
11: pulse width capture mode
Bit 5
T1S: timer clock source
0: fSYS/4
1: fSUB, LXT or LIRC
Bit 4
T1ON: Timer/event counter counting enable
0: disable
1: enable
Bit 3
T1E:
Event counter active edge selection
0: count on raising edge
1: count on falling edge
Pulse width capture active edge selection
0: start counting on falling edge, stop on rasing edge
1: start counting on raising edge, stop on falling edge
Bit 2~0
unimplemented, read as “0”
MISC Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
ODE3
ODE2
ODE1
ODE0
—
—
PFDSEL
PFDEN
R/W
R/W
R/W
R/W
R/W
—
—
R/W
R/W
POR
0
0
0
0
—
—
0
0
Bit 7
ODE3: PB3 Open Drain Control
0: disable
1: enable
Bit 6
ODE2: PB2 Open Drain Control
0: disable
1: enable
Bit 5
ODE1: PB1 Open Drain Control
0: disable
1: enable
Bit 4
ODE0: PB0 Open Drain Control
0: disable
1: enable
Bit 3~2
Unimplemented, read as “0”
Bit 1
PFDSEL: PFD clock selection
0: Timer 0 output
1: Timer 1 output
Bit 0
PFDEN: PFD function control
0: PFD disable
1: PFD enable
73
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
I/O Interfacing
The Timer/Event Counter, when configured to run in the event counter or pulse width measurement
mode, require the use of the external pin for correct operation. As this pin is a shared pin it must be
configured correctly to ensure it is setup for use as a Timer/Event Counter input and not as a normal
I/O pin. This is implemented by ensuring that the mode select bits in the Timer/Event Counter
control register, select either the event counter or pulse width measurement mode. Additionally
the Port Control Register must be set high to ensure that the pin is setup as an input. Any pull-high
resistor on this pin will remain valid even if the pin is used as a Timer/Event Counter input.
Timer/Event Counter Pins Internal Filter
The external Timer/Event Counter pins are connected to an internal filter to reduce the possibility
of unwanted event counting events or inaccurate pulse width measurements due to adverse noise or
spikes on the external Timer/Event Counter input signal. As this internal filter circuit will consume a
limited amount of power, a configuration option is provided to switch off the filter function, an option
which may be beneficial in power sensitive applications, but in which the integrity of the input signal
is high. Care must be taken when using the filter on/off configuration option as it will be applied
not only to both external Timer/Event Counter pins but also to the external interrupt input pins.
Individual Timer/Event Counter or external interrupt pins cannot be selected to have a filter on/off
function.
Programming Considerations
When configured to run in the timer mode, the internal system clock is used as the timer clock
source and is therefore synchronised with the overall operation of the microcontroller. In this mode
when the appropriate timer register is full, the microcontroller will generate an internal interrupt
signal directing the program flow to the respective internal interrupt vector. For the pulse width
measurement mode, the internal system clock is also used as the timer clock source but the timer
will only run when the correct logic condition appears on the external timer input pin. As this is
an external event and not synchronized with the internal timer clock, the microcontroller will only
see this external event when the next timer clock pulse arrives. As a result, there may be small
differences in measured values requiring programmers to take this into account during programming.
The same applies if the timer is configured to be in the event counting mode, which again is an
external event and not synchronised with the internal system or timer clock.
When the Timer/Event Counter is read, or if data is written to the preload register, the clock is
inhibited to avoid errors, however as this may result in a counting error, this should be taken into
account by the programmer. Care must be taken to ensure that the timers are properly initialised
before using them for the first time. The associated timer enable bits in the interrupt control
register must be properly set otherwise the internal interrupt associated with the timer will remain
inactive. The edge select, timer mode and clock source control bits in timer control register must
also be correctly set to ensure the timer is properly configured for the required application. It is
also important to ensure that an initial value is first loaded into the timer registers before the timer
is switched on; this is because after power-on the initial values of the timer registers are unknown.
After the timer has been initialised the timer can be turned on and off by controlling the enable bit in
the timer control register. Note that setting the timer enable bit high to turn the timer on, should only
be executed after the timer mode bits have been properly setup. Setting the timer enable bit high
together with a mode bit modification, may lead to improper timer operation if executed as a single
timer control register byte write instruction.
Rev. 1.00
74
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
When the Timer/Event counter overflows, its corresponding interrupt request flag in the interrupt
control register will be set. If the timer interrupt is enabled this will in turn generate an interrupt
signal. However irrespective of whether the interrupts are enabled or not, a Timer/Event counter
overflow will also generate a wake-up signal if the devices are in a Power-down condition. This
situation may occur if the Timer/Event Counter is in the Event Counting Mode and if the external
signal continues to change state. In such a case, the Timer/Event Counter will continue to count
these external events and if an overflow occurs the devices will be woken up from its Power-down
condition. To prevent such a wake-up from occurring, the timer interrupt request flag should first be
set high before issuing the HALT instruction to enter the Power Down Mode.
Timer Program Example
This program example shows how the Timer/Event Counter registers are setup, along with how the
interrupts are enabled and managed. Note how the Timer/Event Counter is turned on, by setting bit
4 of the Timer Control Register. The Timer/Event Counter can be turned off in a similar way by
clearing the same bit. This example program sets the Timer/Event Counter to be in the timer mode,
which uses the internal system clock as the clock source.
org 04h; external interrupt vector
org 0ch ; Timer/Event Counter 0 interrupt vector
jmp tmrint ; jump here when the Timer/Event Counter 0 overflows
:
org 20h; main program
; internal Timer/Event Counter 0 interrupt routine
:
tmrint:
; Timer/Event Counter 0 main program placed here
:
reti:
:
begin:
; setup Timer 0 registers
mov a,09bh; setup Timer 0 preload value
mov tmr0,a;
mov a,081h ; setup Timer 0 control register
mov tmr0c,a ; timer mode and prescaler set to /2
; setup interrupt register
mov a,009h ; enable master interrupt and timer interrupt
mov intc0,a
set tmr0c.4 ; start Timer/Event Counter 0 - note mode bits must be previously
; setup
Rev. 1.00
75
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Pulse Width Modulator
The devices contain two channels of 8-bit PWM function respectively. Useful for such applications
such as motor speed control, the PWM function provides outputs with a fixed frequency but with a
duty cycle that can be varied by setting particular values into the corresponding PWM register.
PWM Operation
A single register, known as PWMn and located in the Data Memory is assigned to each Pulse Width
Modulator channel. It is here that the 8-bit value, which represents the overall duty cycle of one
modulation cycle of the output waveform, should be placed. To increase the PWM modulation
frequency, each modulation cycle is subdivided into two or four individual modulation subsections,
known as the 7+1 mode or 6+2 mode respectively. The required mode and the on/off control for
each PWM channel is selected using the BPCTL register. Note that when using the PWM, it is only
necessary to write the required value into the PWMn register and select the required mode setup and
on/off control using the BPCTL registers, the subdivision of the waveform into its sub-modulation
cycles is implemented automatically within the microcontroller hardware. The PWM clock source
is the system clock fSYS. This method of dividing the original modulation cycle into a further 2
or 4 sub-cycles enable the generation of higher PWM frequencies which allow a wider range of
applications to be served. The difference between what is known as the PWM cycle frequency and
the PWM modulation frequency should be understood. As the PWM clock is the system clock, fSYS,
and as the PWM value is 8-bits wide, the overall PWM cycle frequency is fSYS/256. However, when
in the 7+1 mode of operation the PWM modulation frequency will be fSYS/128, while the PWM
modulation frequency for the 6+2 mode of operation will be fSYS/64.
PWM Modulation
PWM Cycle Frequency
PWM Cycle Duty
fSYS/256
[PWM]/256
fSYS/64 for (6+2) bits mode
fSYS/128for (7+1) bits mode
BPCTL Register
Bit
Name
7
6
5
PMODE PWM1EN PWM0EN
4
3
2
1
0
BC1
BC0
BZ2
BZ1
BZ0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7
PMODE: PWM type selection
0: 7+1 mode
1: 6+2 mode
Bit 6
PWM1EN: PWM1 or the other pin-shared functions
0: the other pin-shared functions
1: PWM1
Bit 5
PWM0EN: PWM0 or the other pin-shared functions
0: the other pin-shared functions
1: PWM0
Bit 4~0
Buzzer output and I/O configuration selection, described elsewhere
It should be noted that the PWM0 and PWM1 are not connected to the external pins.
Rev. 1.00
76
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
6+2 PWM Mode
Each full PWM cycle, as it is controlled by an 8-bit PWM register, has 256 clock periods. However,
in the 6+2 PWM mode, each PWM cycle is subdivided into four individual sub-cycles known as
modulation cycle 0 ~ modulation cycle 3, denoted as i in the table. Each one of these four sub-cycles
contains 64 clock cycles. In this mode, a modulation frequency increase of four is achieved. The
8-bit PWM register value, which represents the overall duty cycle of the PWM waveform, is divided
into two groups. The firs mrnr t group which consists of bit2~bit7 is denoted here as the DC value.
The second group which consists of bit0~bit1 is known as the AC value. In the 6+2 PWM mode, the
duty cycle value of each of the four modulation sub-cycles is shown in the following table.
Parameter
AC (0~3)
DC (Duty Cycle)
i<AC
DC+1
64
i≥AC
DC
64
Modulation cycle i
(i=0~3)
6+2 Mode Modulation Cycle Values
The following diagram illustrates the waveforms associated with the 6+2 mode of PWM operation.
It is important to note how the single PWM cycle is subdivided into 4 individual modulation cycles,
numbered from 0~3 and how the AC value is related to the PWM value.
  6+2 PWM Mode
PWM Register for 6+2 Mode
Rev. 1.00
77
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
7+1 PWM Mode
Each full PWM cycle, as it is controlled by an 8-bit PWM register, has 256 clock periods. However,
in the 7+1 PWM mode, each PWM cycle is subdivided into two individual sub-cycles known as
modulation cycle 0 ~ modulation cycle 1, denoted as i in the table. Each one of these two sub-cycles
contains 128 clock cycles. In this mode, a modulation frequency increase of two is achieved. The 8-bit
PWM register value, which represents the overall duty cycle of the PWM waveform, is divided into
two groups. The first group which consists of bit1~bit7 is denoted here as the DC value. The second
group which consists of bit0 is known as the AC value. In the 7+1 PWM mode, the duty cycle value
of each of the two modulation sub-cycles is shown in the following table.
Parameter
AC (0~1)
DC (Duty Cycle)
i<AC
DC+1
128
i≥AC
DC
128
Modulation cycle i
(i=0~1)
7+1 Mode Modulation Cycle Values
The following diagram illustrates the waveforms associated with the 7+1 mode PWM operation. It
is important to note how the single PWM cycle is subdivided into 2 individual modulation cycles,
numbered 0 and 1 and how the AC value is related to the PWM value.
     7+1 PWM Mode
PWM Register for 7+1 Mode
Rev. 1.00
78
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
PWM Output Control
The PWM outputs are pin-shared with the I/O pins PC5 and PC6. To operate as a PWM output
and not as an I/O pin, the correct bits must be set in the BPCTL register. A high value must be
written to the PWM0EN or PWM1EN to select the corresponding PWM. A zero value must also be
written to the corresponding bit in the I/O port control register PCC5 and PCC6 to ensure that the
corresponding PWM output pin is setup as an output. After these two initial steps have been carried
out, and of course after the required PWM value has been written into the PWMn register, writing
a high value to the corresponding bit in the output data register PC5 and PC6 will enable the PWM
data to appear on the pin. Writing a zero value will disable the PWM output function and force the
output low. In this way, the Port data output registers can be used as an on/off control for the PWM
function. Note that if the BPCTL register has selected the PWM function, but a high value has been
written to its corresponding bit in the PCC control register to configure the pin as an input, then the
pin can still function as a normal input line, with pull-high resistor options.
PWM Programming Example
The following sample program shows how the PWM0 output is setup and controlled.
mov a,64h ; setup PWM value of decimal 100
mov pwm0,a
clr bpctl.7 ; select the 7+1 PWM mode
set bpctl.5 ; select PWM0
clr pcc.5 ; setup pin PC5
set pc.5 ; enable the PWM output
:
:
clr pc.5 ; disable the PWM output pin,PC5 forced low
Rev. 1.00
79
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Analog to Digital Converter
The need to interface to real world analog signals is a common requirement for many electronic
systems. However, to properly process these signals by a microcontroller, they must first be
converted into digital signals by A/D converters. By integrating the A/D conversion electronic
circuitry into the microcontroller, the need for external components is reduced significantly with the
corresponding follow-on benefits of lower costs and reduced component space requirements.
A/D Overview
The devices contain an 8/10-channel analog to digital converter which can directly interface to
external analog signals, such as that from sensors or other control signals and convert these signals
directly into either a 12-bit digital value.
Part No.
Input Channels
A/D Channel Select Bits
Input Pins
HT45FH23A
3+2 (from OPA1 and OPA2 output pins)
ACS2~ACS0
AN3~AN5
HT45FH24A
3+2 (from OPA1 and OPA2 output pins)
ACS3~ACS0
AN3~AN5
Note: 1. For the HT45FH23A, AN0~AN2 pins are not connected to the external pins.
2. For the HT45FH24A, AN0~AN2 and AN6~AN7 pins are not connected to the external pins.
The accompanying block diagram shows the overall internal structure of the A/D converter, together
with its associated registers.
 ­       
     € ‚ ƒ ‚ „ € 
  ‚ ƒ ‚ „ 
  
 
Note: "*" AN0~AN2 and VREF/VCAP pins are not connected to the external pins and internally used only.
HT45FH23A A/D Converter Structure
 ­ 
€

 
    
€
‚     
  
    ƒ „ „ † ƒ  ‡
„ „ †  ‡
 
 
Note: "*" AN0~AN2, AN6~AN7 and VREF/VCAP pins are not connected to the external pins and
internally used only.
HT45FH24A A/D Converter Structure
Rev. 1.00
80
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
A/D Converter Register Description
Overall operation of the A/D converter is controlled using five registers. A read only register pair
exists to store the ADC data 12-bit value. The remaining three registers are control registers which
setup the operating and control function of the A/D converter.
Bit
Register
Name
7
ADCR
START
ACSR
—
ADPCR
—
—
6
5
4
3
2
1
0
EOCB
—
—
—
ACS2
ACS1
ACS0
ADONB
VRSEL
—
—
ADCS2
ADCS1
ADCS0
PCR5
PCR4
PCR3
PCR2
PCR1
PCR0
1
0
A/D Converter Register List – HT45FH23A
Bit
Register
Name
7
ADCR
START
ACSR
—
ADPCR
PCR7
PCR6
6
5
4
3
2
EOCB
—
—
ACS3
ACS2
ACS1
ACS0
ADONB
VRSEL
—
—
ADCS2
ADCS1
ADCS0
PCR5
PCR4
PCR3
PCR2
PCR1
PCR0
A/D Converter Register List – HT45FH24A
A/D Converter Data Registers – ADRL, ADRH
As the devices contain an internal 12-bit A/D converter respectively, they require two data registers
to store the converted value. These are a high byte register, known as ADRH, and a low byte register,
known as ADRL. After the conversion process takes place, these registers can be directly read by the
microcontroller to obtain the digitised conversion value. D0~D11 are the A/D conversion result data
bits. Any unused bits will be read as zero.
ADRH
ADRL
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
A/D Data Registers
A/D Converter Control Registers – ADCR, ACSR, ADPCR
To control the function and operation of the A/D converter, three control registers known as ADCR,
ACSR and ADPCR are provided. These 8-bit registers define functions such as the selection of
which analog channel is connected to the internal A/D converter, the digitised data format, the
A/D clock source as well as controlling the start function and monitoring the A/D converter end
of conversion status. The ACS3~ACS0 bits in the ADCR register define the ADC input channel
number. As the devices contain only one actual analog to digital converter hardware circuit for the
HT45FH24A, each of the individual 5 analog inputs, which include 3 external A/D channels and 2
internal OPA outputs, must be routed to the converter. It is the function of the ACS3~ACS0 bits to
determine which analog channel input pin is actually connected to the internal A/D converter.
The ADPCR control register contains the PCR7~PCR0 bits which determine which pins on Port B,
Port C and Port D are used as analog inputs for the A/D converter input and which pins are not to
be used as the A/D converter input. Setting the corresponding bit high will select the A/D input
function, clearing the bit to zero will select either the I/O or other pin-shared function. When the
pin is selected to be an A/D input, its original function whether it is an I/O or other pin-shared
function will be removed. In addition, any internal pull-high resistors connected to these pins will be
automatically removed if the pin is selected to be an A/D input.
Rev. 1.00
81
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
ADCR Register
• HT45FH23A
Bit
7
6
5
4
3
2
1
0
Name
START
EOCB
—
—
—
ACS2
ACS1
ACS0
R/W
R/W
R
—
—
—
R/W
R/W
R/W
POR
0
1
—
—
—
0
0
0
Bit 7
START: Start the A/D conversion
0→1→0: start
0→1: reset the A/D converter and set EOCB to “1”
This bit is used to initiate an A/D conversion process. The bit is normally low but if set
high and then cleared low again, the A/D converter will initiate a conversion process.
When the bit is set high the A/D converter will be reset.
Bit 6
EOCB: End of A/D conversion flag
0: A/D conversion ended
1: A/D conversion in progress
This read only flag is used to indicate when an A/D conversion process has completed.
When the conversion process is running the bit will be high.
Bit 5~3
unimplemented, read as “0”
Bit 2~0
ACS2 ~ ACS0: Select A/D channel
000: AN0
001: AN1
010: AN2
011: AN3
100: AN4
101: AN5
110: connect Op Amp 1 output (A1E)
111: connect Op Amp 2 output (A2E)
These are the A/D channel select control bits. As there is only one internal hardware
A/D converter each of the eight A/D inputs must be routed to the internal converter
using these bits.
It should be noted that the AN0~AN2 are not connected to the external pins.
• HT45FH24A
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
START
EOCB
—
—
ACS3
ACS2
ACS1
ACS0
R/W
R/W
R
—
—
R/W
R/W
R/W
R/W
POR
0
1
—
—
0
0
0
0
Bit 7
START: Start the A/D conversion
0→1→0: start
0→1: reset the A/D converter and set EOCB to “1”
This bit is used to initiate an A/D conversion process. The bit is normally low but if set
high and then cleared low again, the A/D converter will initiate a conversion process.
When the bit is set high the A/D converter will be reset.
Bit 6
EOCB: End of A/D conversion flag
0: A/D conversion ended
1: A/D conversion in progress
This read only flag is used to indicate when an A/D conversion process has completed.
When the conversion process is running the bit will be high.
Bit 5~4
unimplemented, read as “0”
82
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit 3~0
ACS3 ~ ACS0: Select A/D channel
0000: AN0
0001: AN1
0010: AN2
0011: AN3
0100: AN4
0101: AN5
0110: connect Op Amp 1 output (A1E)
0111: connect Op Amp 2 output (A2E)
1000: AN6
1001: AN7
These are the A/D channel select control bits. As there is only one internal hardware A/D
converter each of the ten A/D inputs must be routed to the internal converter using these
bits.
It should be noted that the AN0~AN2 are not connected to the external pins.
ACSR Register
Bit
Rev. 1.00
7
6
5
4
3
2
1
0
Name
—
ADONB
VRSEL
R/W
—
R/W
R/W
—
—
ADCS2
ADCS1
ADCS0
—
—
R/W
R/W
POR
1
0
0
—
R/W
—
0
0
0
Bit 7
unimplemented, read as “1”
Bit 6
ADONB: ADC module power on/off control bit
0: ADC module power on
1: ADC module power off
This bit controls the power to the A/D internal function. This bit should be cleared
to zero to enable the A/D converter. If the bit is set high then the A/D converter will
be switched off reducing the devices power consumption. As the A/D converter will
consume a limited amount of power,even when not executing a conversion, this may
be an important consideration in power sensitive battery powered applications.
Note: 1. it is recommended to set ADONB=1 before entering IDLE/SLEEP Mode for
saving power.
2. ADONB=1 will power down the ADC module.
Bit 5
VRSEL: Selecte ADC reference voltage
0: Internal ADC power
1: VREF pin or LDO output (2.4V/3.3V)
This bit is used to select the reference voltage for the A/D converter. If the bit is high,
then the A/D converter reference voltage is supplied on the external VREF pin or LDO
output (2.4V/3.3V). If the pin is low, then the internal reference is used which is taken
from the power supply pin VDD.
It should be noted that the VREF/VCAP is not connected to the external pin.
Bit 4~3
unimplemented, read as “0”
Bit 2~0
ADCS2, ADCS1, ADCS0: Select ADC clock source
000: fSYS/2
001: fSYS/8
010: fSYS/32
011: Undefined
100: fSYS
101: fSYS/4
110: fSYS/16
111: Undefined
These three bits are used to select the clock source for the A/D converter.
83
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
ADPCR Register
• HT45FH23A
Bit
7
6
5
4
3
2
1
0
Name
—
—
PCR5
PCR4
PCR3
PCR2
PCR1
PCR0
R/W
—
—
R/W
R/W
R/W
R/W
R/W
R/W
POR
—
—
0
0
0
0
0
0
Bit 7~6
unimplemented, read as “0”
Bit 5
PCR5: Define PC1 is A/D input or not
0: Not A/D input
1: A/D input, AN5
Bit 4
PCR4: Define PC0 is A/D input or not
0: Not A/D input
1: A/D input, AN4
Bit 3
PCR3: Define PB6 is A/D input or not
0: Not A/D input
1: A/D input, AN3
Bit 2
PCR2: Define PB5 is A/D input or not
0: Not A/D input
1: A/D input, AN2
Bit 1
PCR1: Define PB4 is A/D input or not
0: Not A/D input
1: A/D input, AN1
Bit 0
PCR0: Define PB3 is A/D input or not
0: Not A/D input
1: A/D input, AN0
It should be noted that the PB3/AN0/SCS, PB4/AN1/AUD/PCK and PB5/AN2/PINT
are not connected to the external pins.
• HT45FH24A
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
PCR7
PCR6
PCR5
PCR4
PCR3
PCR2
PCR1
PCR0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7
PCR7: Define PD1 is A/D input or not
0: Not A/D input
1: A/D input, AN7
Bit 6
PCR6: Define PD0 is A/D input or not
0: Not A/D input
1: A/D input, AN6
Bit 5
PCR5: Define PC1 is A/D input or not
0: Not A/D input
1: A/D input, AN5
Bit 4
PCR4: Define PC0 is A/D input or not
0: Not A/D input
1: A/D input, AN4
Bit 3
PCR3: Define PB6 is A/D input or not
0: Not A/D input
1: A/D input, AN3
Bit 2
PCR2: Define PB5 is A/D input or not
0: Not A/D input
1: A/D input, AN2
84
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit 1
PCR1: Define PB4 is A/D input or not
0: Not A/D input
1: A/D input, AN1
Bit 0
PCR0: Define PB3 is A/D input or not
0: Not A/D input
1: A/D input, AN0
It should be noted that the PB3/AN0/SCS, PB4/AN1/AUD/PCK, PB5/AN2/PINT,
PD0/AN6, PD1/AN7 pins are not connected to the external pins.
A/D Operation
The START bit in the ADCR register is used to start and reset the A/D converter. When the
microcontroller sets this bit from low to high and then low again, an analog to digital conversion
cycle will be initiated. When the START bit is brought from low to high but not low again, the
EOCB bit in the ADCR register will be set high and the analog to digital converter will be reset. It
is the START bit that is used to control the overall start operation of the internal analog to digital
converter.
The EOCB bit in the ADCR register is used to indicate when the analog to digital conversion process
is complete. This bit will be automatically set to “0” by the microcontroller after a conversion cycle
has ended. In addition, the corresponding A/D interrupt request flag will be set in the interrupt
control register, and if the interrupts are enabled, an appropriate internal interrupt signal will be
generated. This A/D internal interrupt signal will direct the program flow to the associated A/D
internal interrupt address for processing. If the A/D internal interrupt is disabled, the microcontroller
can be used to poll the EOCB bit in the ADCR register to check whether it has been cleared as an
alternative method of detecting the end of an A/D conversion cycle.
The clock source for the A/D converter, which originates from the system clock fSYS, can be chosen
to be either fSYS or a subdivided version of fSYS. The division ratio value is determined by the
ADCS2~ADCS0 bits in the ACSR register.
Although the A/D clock source is determined by the system clock fSYS, and by bits ADCS2~ADCS0,
there are some limitations on the maximum A/D clock source speed that can be selected. As the
minimum value of permissible A/D clock period, tAD, is 0.5µs, care must be taken for system clock
frequencies equal to or greater than 4MHz. For example, if the system clock operates at a frequency
of 4MHz, the ADCS2~ADCS0 bits should not be set to “100”. Doing so will give A/D clock periods
that are less than the minimum A/D clock period which may result in inaccurate A/D conversion
values. Refer to the following table for examples, where values marked with an asterisk * show
where, depending upon the devices, special care must be taken, as the values may be less than the
specified minimum A/D Clock Period.
A/D Clock Period (tAD)
ADCS2,
ADCS1,
ADCS0
= 100
(fSYS)
ADCS2,
ADCS1,
ADCS0
= 000
(fSYS/2)
ADCS2,
ADCS1,
ADCS0
= 101
(fSYS/4)
ADCS2,
ADCS1,
ADCS0
= 001
(fSYS/8)
ADCS2,
ADCS1,
ADCS0
= 110
(fSYS/16)
ADCS2,
ADCS1,
ADCS0
= 010
(fSYS/32)
ADCS2,
ADCS1,
ADCS0
= 111
= 011
1MHz
1µs
2µs
4µs
8µs
16µs
32µs
Undefined
2MHz
500ns
1µs
2µs
4µs
8µs
16µs
Undefined
4MHz
250ns*
500ns
1µs
2µs
4µs
8µs
Undefined
8MHz
125ns*
250ns*
500ns
1µs
2µs
4µs
Undefined
12MHz
83ns*
167ns*
333ns*
667ns
1.33µs
2.67µs
Undefined
fSYS
A/D Clock Period Examples
Rev. 1.00
85
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Controlling the power on/off function of the A/D converter circuitry is implemented using the
ADONB bit in the ACSR register. This bit must be zero to power on the A/D converter. When the
ADONB bit is cleared to zero to power on the A/D converter internal circuitry a certain delay, as
indicated in the timing diagram, must be allowed before an A/D conversion is initiated. Even if no
pins are selected for use as A/D inputs by clearing the PCR7~PCR0 bits in the ADPCR register, if
the ADONB bit is zero then some power will still be consumed. In power conscious applications it
is therefore recommended that the ADONB is set high to reduce power consumption when the A/D
converter function is not being used.
The reference voltage supply to the A/D Converter can be supplied from either the positive power
supply pin, VDD, or from an external reference sources supplied on pin VREF. The desired selection
is made using the VRSEL bit. As the VREF pin is pin-shared with other functions, when the VRSEL
bit is set high, the VREF pin function will be selected and the other pin functions will be disabled
automatically.
A/D Input Pins
The A/D analog input pins are pin-shared with the I/O pins on Port B Port C and Port D as well as
other functions. The PCR7~ PCR0 bits in the ADPCR register, determine whether the input pins
are setup as A/D converter analog inputs or whether they have other functions. If the PCR7~ PCR0
bits for its corresponding pin is set high then the pin will be setup to be an A/D converter input
and the original pin functions disabled. In this way, pins can be changed under program control to
change their function between A/D inputs and other functions. All pull-high resistors, which are
setup through register programming, will be automatically disconnected if the pins are setup as A/D
inputs. Note that it is not necessary to first setup the A/D pin as an input in the PBC or PCC or PDC
port control register to enable the A/D input as when the PCR7~ PCR0 bits enable an A/D input, the
status of the port control register will be overridden.

    

    Note: 1. The HT45FH23A I/O lines, AN0~AN2 and VREF/VCAP pins are not connected to the
external pins.
2. The HT45FH24A I/O lines, AN0~AN2, AN6~AN7 and VREF/VCAP pins are not
connected to the external pins.
A/D Input Structure
The A/D converter has its own reference voltage pin, VREF, however the reference voltage can also
be supplied from the power supply pin, a choice which is made through the VRSEL bit in the ACSR
register. The analog input values must not be allowed to exceed the value of VREF.
Rev. 1.00
86
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Summary of A/D Conversion Steps
The following summarises the individual steps that should be executed in order to implement an A/D
conversion process.
• Step 1
Select the required A/D conversion clock by correctly programming bits ADCS2~ADCS0 in the
ACSR register.
• Step 2
Enable the A/D by clearing the ADONB bit in the ACSR register to zero.
• Step 3
Select which channel is to be connected to the internal A/D converter by correctly programming
the ACS3~ACS0 bits which are also contained in the ADCR register.
• Step 4
Select which pins are to be used as A/D inputs and configure them by correctly programming the
PCR7~PCR0 bits in the ADPCR register.
• Step 5
If the interrupts are to be used, the interrupt control registers must be correctly configured to
ensure the A/D converter interrupt function is active. The master interrupt control bit, EMI,
Mulit-function interrupt bit, and the A/D converter interrupt bit, EADI, must all be set high to do
this.
• Step 6
The analog to digital conversion process can now be initialised by setting the START bit in
the ADCR register from low to high and then low again. Note that this bit should have been
originally cleared to zero.
• Step 7
To check when the analog to digital conversion process is complete, the EOCB bit in the ADCR
register can be polled. The conversion process is complete when this bit goes low. When this
occurs the A/D data registers ADRL and ADRH can be read to obtain the conversion value. As an
alternative method, if the interrupts are enabled and the stack is not full, the program can wait for
an A/D interrupt to occur.
Note: When checking for the end of the conversion process, if the method of polling the EOCB
bit in the ADCR register is used, the interrupt enable step above can be omitted.
The accompanying diagram shows graphically the various stages involved in an analog to digital
conversion process and its associated timing. After an A/D conversion process has been initiated
by the application program, the microcontroller internal hardware will begin to carry out the
conversion, during which time the program can continue with other functions. The time taken for the
A/D conversion is 16tAD where tAD is equal to the A/D clock period.
Rev. 1.00
87
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
­ €  
­
­ 
                     
 A/D Conversion Timing
Programming Considerations
During microcontroller operations where the A/D converter is not being used, the A/D internal
circuitry can be switched off to reduce power consumption, by setting bit ADONB high in the ACSR
register. When this happens, the internal A/D converter circuits will not consume power irrespective
of what analog voltage is applied to their input lines. If the A/D converter input lines are used as
normal I/Os, then care must be taken as if the input voltage is not at a valid logic level, then this may
lead to some increase in power consumption.
A/D Transfer Function
As the devices contain a 12-bit A/D converter respectively, its full-scale converted digitised value is
equal to FFFH. Since the full-scale analog input value is equal to the VDD or VREF voltage, this gives
a single bit analog input value of VDD or VREF divided by 4096.
1 LSB= (VDD or VREF) ÷ 4096
The A/D Converter input voltage value can be calculated using the following equation:
A/D input voltage = A/D output digital value × (VDD or VREF) ÷ 4096
The diagram shows the ideal transfer function between the analog input value and the digitised
output value for the A/D converter. Except for the digitised zero value, the subsequent digitised
values will change at a point 0.5 LSB below where they would change without the offset, and the
last full scale digitised value will change at a point 1.5 LSB below the VDD or VREF level.
Rev. 1.00
88
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
1.5 LSB
FFFH
FFEH
FFDH
A/D Conve�sion
Result
03H
0.5 LSB
0�H
01H
0
1
�
3
�093 �09� �095
VDD o� VREF
�096
Analog Input Voltage
Ideal A/D Transfer Function
A/D Programming Example
The following two programming examples illustrate how to setup and implement an A/D
conversion. In the first example, the method of polling the EOCB bit in the ADCR register is used to
detect when the conversion cycle is complete, whereas in the second example, the A/D interrupt is
used to determine when the conversion is complete.
Example: using an EOCB polling method to detect the end of conversion
clr EADI;
mov a,01H
mov ACSR,a ;
;
mov a,FFh ;
mov ADPCR,a
mov a,03h
mov ADCR,a ;
:
start_conversion:
clr START ;
set START ;
clr START ;
polling_EOC:
sz EOCB ;
jmp polling_EOC ;
mov a,ADRL ;
mov ADRL_buffer,a ;
mov a,ADRH ;
mov ADRH_buffer,a ;
:
:
jmp start_conversion ;
Rev. 1.00
disable ADC interrupt
select fSYS/8 as A/D clock
Select VDD as ADC reference voltage and turn on ADONB bit
setup ADPCR to configure pins AN0~AN7
enable and connect AN3 channel to A/D converter
high pulse on start bit to initiate conversion
reset A/D
start A/D
poll the ADCR0 register EOCB bit to detect end of A/D conversion
continue polling
read low byte conversion result value
save result to user defined register
read high byte conversion result value
save result to user defined register
start next a/d conversion
89
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Example: using the interrupt method to detect the end of conversion
clr EADI;
mov a,01H
mov ACSR,a ;
;
mov a,FFh ;
mov ADPCR,a
mov a,03h
mov ADCR,a ;
Start_conversion:
clr START ;
set START ;
clr START ;
clr ADF ;
set EADI;
set EMFI ;
set EMI ;
:
:
;
ADC_ISR:
mov acc_stack,a ;
mov a,STATUS
mov status_stack,a
;
:
:
mov a,ADRL ;
mov adrl_buffer,a ;
mov a,ADRH ;
mov adrh_buffer,a ;
:
:
EXIT_INT_ISR:
mov a,status_stack
mov STATUS,a ;
mov a,acc_stack ;
Clr ADF ;
reti
Rev. 1.00
disable ADC interrupt
select fSYS/8 as A/D clock
select VDD as ADC reference voltage and turn on ADONB bit
setup ADPCR to configure pins AN0~AN7
enable and connect AN3 channel to A/D converter
high pulse on START bit to initiate conversion
reset A/D
start A/D
clear ADC interrupt request flag
enable ADC interrupt
enable Multi-function interrupt
enable global interrupt
ADC interrupt service routine
save ACC to user defined memory
save STATUS to user defined memory
read
save
read
save
low byte conversion result value
result to user defined register
high byte conversion result value
result to user defined register
restore STATUS from user defined memory
restore ACC from user defined memory
clear ADC interrupt request flag
90
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Serial Interface Module – SIM
The devices contain a Serial Interface Module respectively, which includes both the four line
SPI interface or the two line I2C interface types, to allow an easy method of communication with
external peripheral hardware. Having relatively simple communication protocols, these serial
interface types allow the microcontroller to interface to external SPI or I2C based hardware such
as sensors, Flash or EEPROM memory, etc. The SIM interface pins are pin-shared with PB0~PB3
pins therefore the SIM interface function must first be selected using a configuration option. As both
interface types share the same pins and registers, the choice of whether the SPI or I2C type is used is
made using the SIM operating mode control bits, named SIM2~SIM0, in the SIMC0 register. These
pull-high resistors of the SIM pin-shared I/O are selected using pull-high control registers, and also
if the SIM function is enabled.
It should be noted that the SPI and I2C pins are not connected to the external pins and internally used
only.
SPI Interface
The SPI interface is often used to communicate with external peripheral device such as sensors,
Flash or EEPROM memory device etc. Originally developed by Motorola, the four line SPI
interface is a synchronous serial data interface that has a relatively simple communication protocol
simplifying the programming requirements when communicating with external hardware device.
The communication is full duplex and operates as a slave/master type, where the devices can be
either master or slave. Although the SPI interface specification can control multiple slave device
from a single master, but this device provides only one SCS pin. If the master needs to control
multiple slave devices from a single master, the master can use I/O pin to select the slave devices.
SPI Interface Operation
The SPI interface is a full duplex synchronous serial data link. It is a four line interface with pin
names SDI, SDO, SCK and SCS. Pins SDI and SDO are the Serial Data Input and Serial Data Output
lines, SCK is the Serial Clock line and SCS is the Slave Select line. As the SPI interface pins are pinshared with PB0~PB3 pins and with the I2C function pins, the SPI interface must first be enabled by
selecting the SIM enable configuration option and setting the correct bits in the SIMC0 and SIMC2
registers. After the SPI configuration option has been configured it can also be additionally disabled
or enabled using the SIMEN bit in the SIMC0 register. Communication between devices connected
to the SPI interface is carried out in a slave/master mode with all data transfer initiations being
implemented by the master. The Master also controls the clock signal. As the device only contains
a single SCS pin only one slave device can be utilized. The SCS pin is controlled by software, set
CSEN bit to “1” to enable SCS pin function, set CSEN bit to “0” the SCS pin will be floating state.
SPI Master/Slave Connection
Rev. 1.00
91
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
The SPI function in this device offers the following features:
• Full duplex synchronous data transfer
• Both Master and Slave modes
• LSB first or MSB first data transmission modes
• Transmission complete flag
• Rising or falling active clock edge
• WCOL and CSEN bit enabled or disable select
ƒ ƒ  
 
ƒ  ­
€ ‚
   
  „ The status of the SPI interface pins is determined by a number of factors such as whether the device
is in the master or slave mode and upon the condition of certain control bits such as CSEN and
SIMEN.
There are several configuration options associated with the SPI interface. One of these is to
enable the SIM function which selects the SIM pins rather than normal I/O pins. Note that if the
configuration option does not select the SIM function then the SIMEN bit in the SIMC0 register will
have no effect. Another two SPI configuration options determine if the CSEN and WCOL bits are to
be used.
SPI Registers
There are three internal registers which control the overall operation of the SPI interface. These are
the SIMD data register and two registers SIMC0 and SIMC2. Note that the SIMC1 register is only
used by the I2C interface.
Bit
Register
Name
7
6
5
4
3
2
1
0
SIMC0
SIM2
SIM1
SIM0
PCKEN
PCKP1
PCKP0
SIMEN
—
SIMD
D7
D6
D5
D4
D3
D2
D1
D0
SIMC2
D7
D6
CKPOLB
CKEG
MLS
CSEN
WCOL
TRF
SIM Registers List
The SIMD register is used to store the data being transmitted and received. The same register is used
by both the SPI and I2C functions. Before the device writes data to the SPI bus, the actual data to
be transmitted must be placed in the SIMD register. After the data is received from the SPI bus, the
device can read it from the SIMD register. Any transmission or reception of data from the SPI bus
must be made via the SIMD register.
Rev. 1.00
92
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
• SIMD Register
Bit
7
6
5
4
3
2
1
0
Name
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
x
x
x
x
x
x
x
x
“x” unknown
Bit 7~0
D7~D0: SIM Data Register bit7~bit0
There are also two control registers for the SPI interface, SIMC0 and SIMC2. Note that the SIMC2
register also has the name SIMA which is used by the I2C function. The SIMC1 register is not used
by the SPI function, only by the I2C function. Register SIMC0 is used to control the enable/disable
function and to set the data transmission clock frequency. Although not connected with the SPI
function, the SIMC0 register is also used to control the Peripheral Clock Prescaler. Register SIMC2
is used for other control functions such as LSB/MSB selection, write collision flag etc.
• SIMC0 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
SIM2
SIM1
SIM0
PCKEN
PCKP1
PCKP0
SIMEN
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
—
POR
1
1
1
0
0
0
0
—
Bit 7~5
SIM2, SIM1, SIM0: SIM Operating Mode Control
000: SPI master mode; SPI clock is fSYS/4
001: SPI master mode; SPI clock is fSYS/16
010: SPI master mode; SPI clock is fSYS/64
011: SPI master mode; SPI clock is fSUB
100: SPI master mode; SPI clock is Timer 0 output/2 (PFD0)
101: SPI slave mode
110: I2C slave mode
111: Unused mode
These bits setup the overall operating mode of the SIM function. As well as selecting
if the I2C or SPI function, they are used to control the SPI Master/Slave selection and
the SPI Master clock frequency. The SPI clock is a function of the system clock but
can also be chosen to be sourced from the Timer 0 or fSUB. If the SPI Slave Mode is
selected then the clock will be supplied by an external Master device.
Bit 4
PCKEN: PCK Output Pin Control
0: Disable
1: Enable
Bit 3~2
PCKP1, PCKP0: Select PCK output pin frequency
00: fSYS
01: fSYS/4
10: fSYS/8
11: Timer 0 output/2 (PFD0)
93
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit 1
SIMEN: SIM Control
0: Disable
1: Enable
The bit is the overall on/off control for the SIM interface. When the SIMEN bit is
cleared to zero to disable the SIM interface, the SDI, SDO, SCK and SCS, or SDA
and SCL lines will be in a floating condition and the SIM operating current will be
reduced to a minimum value. When the bit is high the SIM interface is enabled. The
SIM configuration option must have first enabled the SIM interface for this bit to be
effective. If the SIM is configured to operate as an SPI interface via the SIM2~SIM0
bits, the contents of the SPI control registers will remain at the previous settings when
the SIMEN bit changes from low to high and should therefore be first initialised by
the application program. If the SIM is configured to operate as an I2C interface via the
SIM2~SIM0 bits and the SIMEN bit changes from low to high, the contents of the I2C
control bits such as HTX and TXAK will remain at the previous settings and should
therefore be first initialised by the application program while the relevant I2C flags
such as HCF, HAAS, HBB, SRW and RXAK will be set to their default states.
Bit 0
unimplemented, read as “0”
• SIMC2 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
D7
D6
CKPOLB
CKEG
MLS
CSEN
WCOL
TRF
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~6
Undefined bit
This bit can be read or written by user software program.
Bit 5
CKPOLB: Determines the base condition of the clock line
0: the SCK line will be high when the clock is inactive
1: the SCK line will be low when the clock is inactive
The CKPOLB bit determines the base condition of the clock line, if the bit is high,
then the SCK line will be low when the clock is inactive. When the CKPOLB bit is
low, then the SCK line will be high when the clock is inactive.
Bit 4
CKEG: Determines SPI SCK active clock edge type
CKPOLB=0
0: SCK is high base level and data capture at SCK rising edge
1: SCK is high base level and data capture at SCK falling edge
CKPOLB=1
0: SCK is low base level and data capture at SCK falling edge
1: SCK is low base level and data capture at SCK rising edge
The CKEG and CKPOLB bits are used to setup the way that the clock signal outputs
and inputs data on the SPI bus. These two bits must be configured before data transfer
is executed otherwise an erroneous clock edge may be generated. The CKPOLB bit
determines the base condition of the clock line, if the bit is high, then the SCK line
will be low when the clock is inactive. When the CKPOLB bit is low, then the SCK
line will be high when the clock is inactive. The CKEG bit determines active clock
edge type which depends upon the condition of CKPOLB bit.
Bit 3
MLS: SPI Data shift order
0: LSB
1: MSB
This is the data shift select bit and is used to select how the data is transferred, either
MSB or LSB first. Setting the bit high will select MSB first and low for LSB first.
94
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit 2
CSEN: SPI SCS pin Control
0: Disable
1: Enable
The CSEN bit is used as an enable/disable for the SCS pin. If this bit is low, then the
SCS pin will be disabled and placed into a floating condition. If the bit is high the
SCS pin will be enabled and used as a select pin. Note that using the CSEN bit can be
disabled or enabled via configuration option.
Bit 1
WCOL: SPI Write Collision flag
0: No collision
1: Collision
The WCOL flag is used to detect if a data collision has occurred. If this bit is high it
means that data has been attempted to be written to the SIMD register during a data
transfer operation. This writing operation will be ignored if data is being transferred.
The bit can be cleared by the application program. Note that using the WCOL bit can
be disabled or enabled via configuration option.
Bit 0
TRF: SPI Transmit/Receive Complete flag
0: Data is being transferred
1: SPI data transmission is completed
The TRF bit is the Transmit/Receive Complete flag and is set “1” automatically when
an SPI data transmission is completed, but must set to “0” by the application program.
It can be used to generate an interrupt.
SPI Communication
After the SPI interface is enabled by setting the SIMEN bit high, then in the Master Mode, when
data is written to the SIMD register, transmission/reception will begin simultaneously. When the
data transfer is complete, the TRF flag will be set automatically, but must be cleared using the
application program. In the Slave Mode, when the clock signal from the master has been received,
any data in the SIMD register will be transmitted and any data on the SDI pin will be shifted into
the SIMD register. The master should output an SCS signal to enable the slave device before a
clock signal is provided. The slave data to be transferred should be well prepared at the appropriate
moment relative to the SCS signal depending upon the configurations of the CKPOLB bit and CKEG
bit. The accompanying timing diagram shows the relationship between the slave data and SCS signal
for various configurations of the CKPOLB and CKEG bits.
The SPI will continue to function even in the IDLE Mode.
Rev. 1.00
95
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
               

 ­
 €  ‚
 ‚  €
 ­ 
  
  
 ­
 €  ‚
 ‚  €
 ­ 
  
  
   ƒ
„ 
SPI Master Mode Timing
      
 ­€  
SPI Slave Mode Timing-CKEG=0
          ƒ „
   
 ­  €‚   €  ‚ † ‡ ˆ ‰€  Š ƒ  ˆ Š ƒ ‰  ‚ ‹   Œ ‚ ˆ
 ˆ     ‚ † ‚Ž
SPI Slave Mode Timing-CKEG=1
Rev. 1.00
96
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver

   †‡ ˆ‰ Š ‰ ‰ ‰ „
‰ ‰ „‰ ‰ „‰ ‰ ‰ †‡ ˆ‰ Š ‰ ­ € ‚
ƒ „
‚ „  
 

   SPI Transfer Control Flowchart
Rev. 1.00
97
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
I2C Interface
The I 2C interface is used to communicate with external peripheral device such as sensors,
EEPROM memory etc. Originally developed by Philips, it is a two line low speed serial interface
for synchronous serial data transfer. The advantage of only two lines for communication, relatively
simple communication protocol and the ability to accommodate multiple devices on the same bus
has made it an extremely popular interface type for many applications.
I2C Master Slave Bus Connection
I2C Interface Operation
The I2C serial interface is a two line interface, a serial data line, SDA, and serial clock line, SCL. As
many devices may be connected together on the same bus, their outputs are both open drain types.
For this reason it is necessary that external pull-high resistors are connected to these outputs. Note
that no chip select line exists, as each device on the I2C bus is identified by a unique address which
will be transmitted and received on the I2C bus.
When two devices communicate with each other on the bidirectional I2C bus, one is known as the
master device and one as the slave device. Both master and slave can transmit and receive data,
however, it is the master device that has overall control of the bus. For these devices, which only
operates in slave mode, there are two methods of transferring data on the I2C bus, the slave transmit
mode and the slave receive mode.
There are several configuration options associated with the I2C interface. One of these is to enable
the function which selects the SIM pins rather than normal I/O pins. Note that if the configuration
option does not select the SIM function then the SIMEN bit in the SIMC0 register will have no
effect. A configuration option exists to allow a clock other than the system clock to drive the I2C
interface. Another configuration option determines the debounce time of the I2C interface. This uses
the internal clock to in effect add a debounce time to the external clock to reduce the possibility of
glitches on the clock line causing erroneous operation. The debounce time, if selected, can be chosen
to be either 1 or 2 system clocks.
I2C Registers
There are three control registers associated with the I2C bus, SIMC0, SIMC1 and SIMA and one
data register, SIMD. The SIMD register, which is shown in the above SPI section, is used to store
the data being transmitted and received on the I2C bus. Before the microcontroller writes data to
the I2C bus, the actual data to be transmitted must be placed in the SIMD register. After the data is
received from the I2C bus, the microcontroller can read it from the SIMD register. Any transmission
or reception of data from the I2C bus must be made via the SIMD register.
Note that the SIMA register also has the name SIMC2 which is used by the SPI function. Bit SIMEN
and bits SIM2~SIM0 in register SIMC0 are used by the I2C interface.
Rev. 1.00
98
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
S T A R T s ig n a l
fro m M a s te r
S e n d s la v e a d d r e s s
a n d R /W b it fr o m M a s te r
A c k n o w le d g e
fr o m s la v e
S e n d d a ta b y te
fro m M a s te r
A c k n o w le d g e
fr o m s la v e
S T O P s ig n a l
fro m M a s te r
Bit
Register
Name
7
6
5
4
3
2
1
0
SIMC0
SIM2
SIM1
SIM0
PCKEN
PCKP1
PCKP0
SIMEN
—
SIMC1
HCF
HAAS
HBB
HTX
TXAK
SRW
IAMWU
RXAK
SIMD
D7
D6
D5
D4
D3
D2
D1
D0
SIMA
IICA6
IICA5
IICA4
IICA3
IICA2
IICA1
IICA0
—
I2C Registers List
• SIMC0 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
SIM2
SIM1
SIM0
PCKEN
PCKP1
PCKP0
SIMEN
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
—
POR
1
1
1
0
0
0
0
—
Bit 7~5
SIM2, SIM1, SIM0: Operating Mode Control
000: SPI master mode; SPI clock is fSYS/4
001: SPI master mode; SPI clock is fSYS/16
010: SPI master mode; SPI clock is fSYS/64
011: SPI master mode; SPI clock is fSUB
100: SPI master mode; SPI clock is Timer 0 output/2 (PFD0)
101: SPI slave mode
110: I2C slave mode
111: Unused mode
These bits setup the overall operating mode of the SIM function. As well as selecting
if the I2C or SPI function, they are used to control the SPI Master/Slave selection and
the SPI Master clock frequency. The SPI clock is a function of the system clock but
can also be chosen to be sourced from the Timer 0 or fSUB. If the SPI Slave Mode is
selected then the clock will be supplied by an external Master device.
Bit 4
PCKEN: PCK Output Pin Control
0: Disable
1: Enable
Bit 3~2
PCKP1, PCKP0: Select PCK output pin frequency
00: fSYS
01: fSYS/4
10: fSYS/8
11: Timer 0 output/2 (PFD0)
99
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit 1
SIMEN: SIM Control
0: Disable
1: Enable
The bit is the overall on/off control for the SIM interface. When the SIMEN bit is
cleared to zero to disable the SIM interface, the SDI, SDO, SCK and SCS, or SDA
and SCL lines will be in a floating condition and the SIM operating current will be
reduced to a minimum value. When the bit is high the SIM interface is enabled. The
SIM configuration option must have first enabled the SIM interface for this bit to be
effective. If the SIM is configured to operate as an SPI interface via SIM2~SIM0 bits,
the contents of the SPI control registers will remain at the previous settings when the
SIMEN bit changes from low to high and should therefore be first initialised by the
application program. If the SIM is configured to operate as an I2C interface via the
SIM2~SIM0 bits and the SIMEN bit changes from low to high, the contents of the I2C
control bits such as HTX and TXAK will remain at the previous settings and should
therefore be first initialised by the application program while the relevant I2C flags
such as HCF, HAAS, HBB, SRW and RXAK will be set to their default states.
Bit 0
unimplemented, read as “0”
• SIMC1 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
HCF
HAAS
HBB
HTX
TXAK
SRW
IAMWU
RXAK
R/W
R
R
R
R/W
R/W
R
R/W
R
POR
1
0
0
0
0
0
0
1
Bit 7
HCF: I2C Bus data transfer completion flag
0: Data is being transferred
1: Completion of an 8-bit data transfer
The HCF flag is the data transfer flag. This flag will be zero when data is being
transferred. Upon completion of an 8-bit data transfer the flag will go high and an
interrupt will be generated.
Bit 6
HAAS: I2C Bus address match flag
0: Not address match
1: Address match
The HASS flag is the address match flag. This flag is used to determine if the slave
device address is the same as the master transmit address. If the addresses match then
this bit will be high, if there is no match then the flag will be low.
Bit 5
HBB: I2C Bus busy flag
0: I2C Bus is not busy
1: I2C Bus is busy
The HBB flag is the I2C busy flag. This flag will be “1” when the I2C bus is busy
which will occur when a START signal is detected. The flag will be set to “0” when
the bus is free which will occur when a STOP signal is detected.
Bit 4
HTX: Select I2C slave device is transmitter or receiver
0: Slave device is the receiver
1: Slave device is the transmitter
Bit 3
TXAK: I2C Bus transmit acknowledge flag
0: Slave send acknowledge flag
1: Slave do not send acknowledge flag
The TXAK bit is the transmit acknowledge flag. After the slave device receipt of 8-bits
of data, this bit will be transmitted to the bus on the 9th clock from the slave device.
The slave device must always set TXAK bit to “0” before further data is received.
Bit 2
SRW: I2C Slave Read/Write flag
0: Slave device should be in receive mode
1: Slave device should be in transmit mode
100
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
The SRW flag is the I 2C Slave Read/Write flag. This flag determines whether
the master device wishes to transmit or receive data from the I2C bus. When the
transmitted address and slave address is match, that is when the HAAS flag is set high,
the slave device will check the SRW flag to determine whether it should be in transmit
mode or receive mode. If the SRW flag is high, the master is requesting to read data
from the bus, so the slave device should be in transmit mode. When the SRW flag
is zero, the master will write data to the bus, therefore the slave device should be in
receive mode to read this data.
Bit 1
IAMWU: I2C Address Match Wake-up Control
0: Disable
1: Enable
This bit should be set to “1” to enable I2C address match wake up from SLEEP or
IDLE Mode.
Bit 0
RXAK: I2C Bus Receive acknowledge flag
0: Slave receive acknowledge flag
1: Slave do not receive acknowledge flag
The RXAK flag is the receiver acknowledge flag. When the RXAK flag is “0”, it
means that a acknowledge signal has been received at the 9th clock, after 8 bits of data
have been transmitted. When the slave device in the transmit mode, the slave device
checks the RXAK flag to determine if the master receiver wishes to receive the next
byte. The slave transmitter will therefore continue sending out data until the RXAK
flag is “1”. When this occurs, the slave transmitter will release the SDA line to allow
the master to send a STOP signal to release the I2C Bus.
The SIMD register is used to store the data being transmitted and received. The same register is used
by both the SPI and I2C functions. Before the device writes data to the I2C bus, the actual data to
be transmitted must be placed in the SIMD register. After the data is received from the I2C bus, the
device can read it from the SIMD register. Any transmission or reception of data from the I2C bus
must be made via the SIMD register.
• SIMD Register
Bit
7
6
5
4
3
2
1
0
Name
D7
D6
D5
D4
D3
D2
D1
D0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
x
x
x
x
x
x
x
x
“x” unknown
Bit 7~0
D7~D0: SIM Data Register bit7~bit0
• SIMA Register
Bit
7
6
5
4
3
2
1
0
Name
IICA6
IICA5
IICA4
IICA3
IICA2
IICA1
IICA0
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
—
POR
x
x
x
x
x
x
x
—
“x” unknown
Rev. 1.00
Bit 7~1
IICA6~ IICA0: I2C slave address
IICA6~ IICA0 is the I2C slave address bit 6~ bit 0.
The SIMA register is also used by the SPI interface but has the name SIMC2. The SIMA
register is the location where the 7-bit slave address of the slave device is stored. Bits 7~
1 of the SIMA register define the device slave address. Bit 0 is not defined.
When a master device, which is connected to the I2C bus, sends out an address, which
matches the slave address in the SIMA register, the slave device will be selected. Note
that the SIMA register is the same register address as SIMC2 which is used by the SPI
interface.
Bit 0
Undefined bit
This bit can be read or written by user software program.
101
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
 † †    € ­  ­ ‚ ƒ ƒ  „     ­   
‡ I2C Block Diagram
I2C Bus Communication
Communication on the I2C bus requires four separate steps, a START signal, a slave device address
transmission, a data transmission and finally a STOP signal. When a START signal is placed on
the I2C bus, all devices on the bus will receive this signal and be notified of the imminent arrival of
data on the bus. The first seven bits of the data will be the slave address with the first bit being the
MSB. If the address of the slave device matches that of the transmitted address, the HAAS bit in the
SIMC1 register will be set and an I2C interrupt will be generated. After entering the interrupt service
routine, the slave device must first check the condition of the HAAS bit to determine whether the
interrupt source originates from an address match or from the completion of an 8-bit data transfer.
During a data transfer, note that after the 7-bit slave address has been transmitted, the following bit,
which is the 8th bit, is the read/write bit whose value will be placed in the SRW bit. This bit will be
checked by the slave device to determine whether to go into transmit or receive mode. Before any
transfer of data to or from the I2C bus, the microcontroller must initialise the bus, the following are
steps to achieve this:
• Step 1
Set the SIM2~SIM0 and SIMEN bits in the SIMC0 register to “110” and “1” respectively to
enable the I2C bus.
• Step 2
Write the slave address of the device to the I2C bus address register SIMA.
• Step 3
Set the ESIM of the interrupt control register to enable the SIM interrupt.
Rev. 1.00
102
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
„

­ €  ‚ ƒ  €         I2C Bus Initialisation Flow Chart
I2C Bus Start Signal
The START signal can only be generated by the master device connected to the I2C bus and not by
the slave device. This START signal will be detected by all devices connected to the I2C bus. When
detected, this indicates that the I2C bus is busy and therefore the HBB bit will be set. A START
condition occurs when a high to low transition on the SDA line takes place when the SCL line
remains high.
Slave Address
The transmission of a START signal by the master will be detected by all devices on the I2C bus.
To determine which slave device the master wishes to communicate with, the address of the slave
device will be sent out immediately following the START signal. All slave devices, after receiving
this 7-bit address data, will compare it with their own 7-bit slave address. If the address sent out by
the master matches the internal address of the microcontroller slave device, then an internal I2C bus
interrupt signal will be generated. The next bit following the address, which is the 8th bit, defines
the read/write status and will be saved to the SRW bit of the SIMC1 register. The slave device will
then transmit an acknowledge bit, which is a low level, as the 9th bit. The slave device will also set
the status flag HAAS when the addresses match.
As an I 2C bus interrupt can come from two sources, when the program enters the interrupt
subroutine, the HAAS bit should be examined to see whether the interrupt source has come from
a matching slave address or from the completion of a data byte transfer. When a slave address is
matched, the device must be placed in either the transmit mode and then write data to the SIMD
register, or in the receive mode where it must implement a dummy read from the SIMD register to
release the SCL line.
Rev. 1.00
103
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
I2C Bus Read/Write Signal
The SRW bit in the SIMC1 register defines whether the slave device wishes to read data from the
I2C bus or write data to the I2C bus. The slave device should examine this bit to determine if it is to
be a transmitter or a receiver. If the SRW flag is “1” then this indicates that the master device wishes
to read data from the I2C bus, therefore the slave device must be setup to send data to the I2C bus as
a transmitter. If the SRW flag is “0” then this indicates that the master wishes to send data to the I2C
bus, therefore the slave device must be setup to read data from the I2C bus as a receiver.
I2C Bus Slave Address Acknowledge Signal
After the master has transmitted a calling address, any slave device on the I 2C bus, whose
own internal address matches the calling address, must generate an acknowledge signal. The
acknowledge signal will inform the master that a slave device has accepted its calling address. If no
acknowledge signal is received by the master then a STOP signal must be transmitted by the master
to end the communication. When the HAAS flag is high, the addresses have matched and the slave
device must check the SRW flag to determine if it is to be a transmitter or a receiver. If the SRW flag
is high, the slave device should be setup to be a transmitter so the HTX bit in the SIMC1 register
should be set to “1”. If the SRW flag is low, then the microcontroller slave device should be setup as
a receiver and the HTX bit in the SIMC1 register should be set to “0”.
I2C Bus Data and Acknowledge Signal
The transmitted data is 8-bits wide and is transmitted after the slave device has acknowledged
receipt of its slave address. The order of serial bit transmission is the MSB first and the LSB last.
After receipt of 8-bits of data, the receiver must transmit an acknowledge signal, level “0”, before
it can receive the next data byte. If the slave transmitter does not receive an acknowledge bit signal
from the master receiver, then the slave transmitter will release the SDA line to allow the master
to send a STOP signal to release the I2C Bus. The corresponding data will be stored in the SIMD
register. If setup as a transmitter, the slave device must first write the data to be transmitted into the
SIMD register. If setup as a receiver, the slave device must read the transmitted data from the SIMD
register.
When the slave receiver receives the data byte, it must generate an acknowledge bit, known as
TXAK, on the 9th clock. The slave device, which is setup as a transmitter will check the RXAK bit
in the SIMC1 register to determine if it is to send another data byte, if not then it will release the
SDA line and await the receipt of a STOP signal from the master.
Rev. 1.00
104
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
€


€
­
         ­ Note: * When a slave address is matched, the device must be placed in either the transmit mode
and then write data to the SIMD register, or in the receive mode where it must implement a
dummy read from the SIMD register to release the SCL line.
I2C Communication Timing Diagram
  
 
     I2C Bus ISR Flow Chart
Rev. 1.00
105
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Peripheral Clock Output
The Peripheral Clock Output allows the device to supply external hardware with a clock signal
synchronised to the microcontroller clock.
It should be noted that the PCK pin is not connected to the external pin and internally used only.
Peripheral Clock Operation
As the peripheral clock output pin, PCK, is shared with PB4, the required pin function is chosen
via PCKEN in the SIMC0 register. The Peripheral Clock function is controlled using the SIMC0
register. The clock source for the Peripheral Clock Output can originate from either the Timer 0
output/2 or a divided ratio of the internal fSYS clock. The PCKEN bit in the SIMC0 register is the
overall on/off control, setting PCKEN bit to “1” enables the Peripheral Clock, setting PCKEN
bit to “0” disables it. The required division ratio of the system clock is selected using the PCKP1
and PCKP0 bits in the same register. If the device enters the SLEEP Mode this will disable the
Peripheral Clock output.
SIMC0 Register
Bit
7
6
5
4
3
2
1
0
Name
SIM2
SIM1
SIM0
PCKEN
PCKP1
PCKP0
SIMEN
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
—
POR
1
1
1
0
0
0
0
—
Bit 7~5
Bit 4
Bit 3~2
Bit 1
Bit 0
Rev. 1.00
SIM2, SIM1, SIM0: SIM operating mode control
000: SPI master mode; SPI clock is fSYS/4
001: SPI master mode; SPI clock is fSYS/16
010: SPI master mode; SPI clock is fSYS/64
011: SPI master mode; SPI clock is fSUB
100: SPI master mode; SPI clock is Timer 0 output/2 (PFD0)
101: SPI slave mode
110: I2C slave mode
111: Unused mode
These bits setup the overall operating mode of the SIM function. As well as selecting
if the I2C or SPI function, they are used to control the SPI Master/Slave selection and
the SPI Master clock frequency. The SPI clock is a function of the system clock but
can also be chosen to be sourced from the Timer 0 or fSUB. If the SPI Slave Mode is
selected then the clock will be supplied by an external Master device.
PCKEN: PCK output pin control
0: Disable
1: Enable
PCKP1, PCKP0: select PCK output pin frequency
00: fSYS
01: fSYS/4
10: fSYS/8
11: Timer 0 output/2 (PFD0)
SIMEN: SIM control
0: Disable
1: Enable
The bit is the overall on/off control for the SIM interface. When the SIMEN bit is
cleared to zero to disable the SIM interface, the SDI, SDO, SCK and SCS, or SDA
and SCL lines will be in a floating condition and the SIM operating current will be
reduced to a minimum value. When the bit is high the SIM interface is enabled. The
SIM configuration option must have first enabled the SIM interface for this bit to be
effective. Note that when the SIMEN bit changes from low to high the contents of the
SPI control registers will be in an unknown condition and should therefore be first
initialised by the application program.
unimplemented, read as “0”
106
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
SCOM Function for LCD
The devices have the capability of driving external LCD panels. The common pins for LCD driving,
SCOM0~SCOM3, are pin shared with certain pin on the PA0, PC4~PC6 pins. The LCD signals (COM
and SEG) are generated using the application program.
LCD Operation
An external LCD panel can be driven using this device by configuring the PA0 and PC4~PC6 pins
as common pins and using other output ports lines as segment pins. The LCD driver function is
controlled using the LCDC register which in addition to controlling the overall on/off function also
controls the bias voltage setup function. This enables the LCD COM driver to generate the necessary
VDD/2 voltage levels for LCD 1/2 bias operation.
The LCDEN bit in the LCDC register is the overall master control for the LCD driver, however this
bit is used in conjunction with the COMnEN bits to select which I/O pins are used for LCD driving.
Note that the Port Control register does not need to first setup the pins as outputs to enable the LCD
driver operation.
The following block diagram illustrates the functional structure for LCD COM function.
LCDBUF Disable
LCD SCOM
Output Current
Generator
10uA
25uA
ISEL
Buffer
SCOM0 ~ SCOM3
LCDBUF
LCDBUF Enable
COMnEN
LCDEN
LCD Circuit
LCDEN
COMnEN
0
X
Pin Function Output Level
I/O
High or Low
1
0
I/O
High or Low
1
1
SCOMn
VM
Output Control
LCD Bias Control
The LCD COM driver enables two kinds of selection to be provided to suit the requirement of the
LCD panel which is being used. The bias resistor choice is implemented using the ISEL bit in the
LCDC register.
Rev. 1.00
107
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
LCDC Register
Bit
7
6
5
4
Name
—
LCDBUF
ISEL
LCDEN
3
2
1
0
R/W
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
—
0
0
0
0
0
0
0
COM3EN COM2EN COM1EN COM0EN
Bit 7
unimplemented, read as "0"
Bit 6
LCDBUF: LCD buffer control bit
0: disable
1: enable
Bit 5
ISEL: SCOM operating current selection (VDD=5V)
0: 10µA
1: 25µA
Bit 4
LCDEN: LCD control bit
0: disable
1: enable
The SCOMn can be enable by COMnEN if LCDEN=1.
Bit 3
COM3EN: PC6 or SCOM3 selection
0: GPIO
1: SCOM3
Note: PC6/SCOM3 is not connected to external pin.
Bit 2
COM2EN: PC5 or SCOM2 selection
0: GPIO
1: SCOM2
Note: PC5/SCOM2 is not connected to external pin.
Bit 1
COM1EN: PC4 or SCOM1 selection
0: GPIO
1: SCOM1
Note: PC4/SCOM1 is not connected to external pin.
Bit 0
COM0EN: PA0 or SCOM0 selection
0: GPIO
1: SCOM0
Note: These devices provide the LCD buffer function, which is controlled by LCDBUF flag, to
prevent the interference from LCD panel. With this buffer, that will provide more stable
reference voltages, VH0/1, VL0/1, for OPA and Comparator. It should be noted that if the
LCD SCOM power supply is selected from VLDO or if the LCD panel has larger size, than
the LCD buffer should be turned on to have a higher driver current. However, that will cause
more power consumption to turn on this buffer.
Rev. 1.00
108
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
LDO Function
The devices contain a low power voltage regulator implemented in CMOS technology. Using
CMOS technology ensures low voltage drop and low quiescent current. There are two fixed output
voltages of 2.4V and 3.3V, which can be controlled by a specific register. The internal LDO output
combined with various options by register can provide a fixed voltage for the LCD bias voltage, the
OPA reference voltage, the ADC reference voltage and as a fixed power supply for external device.
LDOC Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
VLOE
REN1
VRES
VSEL
LDOEN
R/W
—
—
—
R/W
R/W
R/W
R/W
R/W
POR
—
—
—
0
0
0
0
0
Bit 7~5
unimplemented, read as "0"
Bit 4
VLOE: LDO output voltage control bit
0: disable
1: enable
If the VLOE and LDOEN are set to “1”, the LDO will output 2.4V or 3.3V to pin and
disable I/O function.
Note: VCAP pin is not connected to external pin.
Bit 3
REN1: Bias voltage divided resistor control bit
0: disable
1: enable
If the REN1is set to “1”, that will turn on the resistor DC path, which will generate
bias voltage for OPAs or LCD SCOM.
Bit 2
VRES: Divided resistor voltage supply selection bit
0: VDD
1: VLDO
Note that the VRES bit will be cleared to 0 by hardware if the LDO is disabled by
setting the LDOEN bit low.
Bit 1
VSEL: LDO output voltage selection bit
0: 2.4V
1: 3.3V
Bit 0
LDOEN: LDO control bit
0: disable
1: enable
109
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
The following block diagram illustrates the functional structure for LDO and divided resister.
LDO
VDD
VSEL
LDOEN
VLOE
VREF/ VCAP
OUT
VLDO VDD
VRES
BUF1
SW4
VLDO VDD
VRSEL
VLDOX
VH1 (0.9* VLDOX)
A/D Reference
Voltage
A/D
Converter
VH0 (0.5+1/16)* VLDOX)
Rtotal= 500K or 200K
VM(0.5* VLDOX)
VL 0 (0.5-1/16)* VLDOX)
VL 1 (0.1* VLDOX)
REN1 or LCDEN
Note: 1. The total resistance of the divided resistor, 500K or 200K, can be selected by the ISEL flag
in LCDC register.
2. To disable the LDO function will turn off the BUF1 as well, no matter the LDO output
voltage control bit, VLOE, is enabled or not.
3. If the LDO output is as the ADC reference voltage, then the VCAP should be connected a
0.1µF capacitor to ground.
4. If the LDO is disabled, LDOEN=0, then the SW4 will be turned to VDD, no matter VRES
flag is “1” or not.
Rev. 1.00
110
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Operational Amplifiers
There are two fully integrated Operational Amplifiers in the devices, OPA1 and OPA2. These OPAs
can be used for signal amplification according to specific user requirements. The OPAs can be
disabled or enabled entirely under software control using internal registers. With specific control
registers, some OPA related applications can be more flexible and easier to be implemented, such as
Unit Gain Buffer, Non-Inverting Amplifier, Inverting Amplifier and various kinds of filters, etc.
Operational Amplifier Registers
The internal Operational Amplifiers are fully under the control of internal registers, OPA1C0,
OPA1C1, OPA2C0, OPA2C1 and OPA2C2. These registers control enable/disable function, input
path selection, gain control and polarity.
OPA1C0 Register
Bit
7
6
5
4
3
2
1
0
Name
A1X
—
—
—
—
—
—
—
R/W
R
—
—
—
—
—
—
—
POR
0
—
—
—
—
—
—
—
Bit 7
A1X: Operational amplifier output; positive logic. This bit is read only.
Bit 6~0
Undefined
OPA1C1 Register
Rev. 1.00
Bit
7
6
5
4
Name
A1O2CIN
A1O2N
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
A1PSEL1 A1PSEL0
3
2
1
0
A1PS
A1NS
A1OEN
A1EN
R/W
R/W
R/W
R/W
1
1
0
0
Bit 7
A1O2CIN: OPA1 output to comparator input control bit
0: disable
1: enable
The A1O2CIN bit should be set to 1 after the CNPSEL bit is set to 0 to ensure that the
OPA1 output is successfully selected as the comparator input.
Bit 6
A1O2N: OPA1 output to OPA1 Inverting input control bit
0: disable
1: enable
This bit is only available when the A1EN bit is set to 1. If the A1EN bit is set to 0, the
A1O2N bit will be cleared to 0 by hardware.
Bit 5~4
A1PSEL1, A1PSEL0: OPA1 Non-inverting input selection bit
00: no connection
01: from VH1 (0.9×VLDO)
10: from VM (0.5×VDD or 0.5×VLDO)
11: from VL1 (0.1×VDD or 0.1×VLDO)
To select the VH1, VM or VL1 as the OPA1 non-inverting input signal by setting the
A2PSEL bit field, the A1PS bit should first be set to 0.
Bit 3
A1PS: A1P pin to OPA1 Non-inverting input control bit
0: no connection
1: from A1P pin
If this bit is set to 1, the A1PSEL field will be cleared to 0 by hardware.
Bit 2
A1NS: A1N pin to OPA1 Inverting input control bit
0: no connection
1: from A1N pin
111
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit 1
A1OEN: OPA1 output enable or disable control bit
0: disable
1: enable
Note: If OPA1 enable and A1OEN set to 1, the MCU will consumption more DC
power (100μA ~ 200μA).
Bit 0
A1EN: OPA1 enable or disable control bit
0: disable
1: enable
If this bit is set to 0, the A1O2N bits will be cleared to 0 by hardware.
OPA2C0 Register
Bit
7
6
5
4
3
2
1
0
Name
A2X
—
—
—
—
—
—
—
R/W
R
—
—
—
—
—
—
—
POR
0
—
—
—
—
—
—
—
Bit 7
A2X: Operational amplifier output; positive logic. This bit is read only.
Bit 6~0
Undefined
OPA2C1 Register
Rev. 1.00
Bit
7
6
Name
A2O2CIN
A2O2N
5
4
R/W
R/W
R/W
R/W
POR
0
0
0
3
2
1
0
A2PS
A2NS
A2OEN
A2EN
R/W
R/W
R/W
R/W
R/W
0
1
1
0
0
A2PSEL1 A2PSEL0
Bit 7
A2O2CIN: OPA2 output to comparator input control bit
0: disable
1: enable
The A2O2CIN bit should be set to 1 after the CNPSEL and A1O2CIN bits are set to 0
to ensure that the OPA2 output is successfully selected as the comparator input.
Bit 6
A2O2N: OPA2 output to OPA2 Inverting input control bit
0: disable
1: enable
This bit is only available when the A2EN bit is set to 1. If the A2EN bit is set to 0, the
A2O2N bit will be cleared to 0 by hardware.
Bit 5~4
A2PSEL1, A2PSEL0: OPA2 Non-inverting input selection bit
00: no connection
01: from VH1 (0.9×VLDO)
10: from VM (0.5×VDD or 0.5×VLDO)
11: from VL1 (0.1×VDD or 0.1×VLDO)
To select the VH1, VM or VL1 signal as the OPA2 non-inverting input by setting the
A2PSEL bit field, the A2PS and A1O2A2P bits should first be set to 0.
Bit 3
A2PS: A2P pin to OPA2 Non-inverting input control bit
0: no connection
1: from A2P pin
If this bit is set to 1, the A1O2A2P bit and A2PSEL field will be cleared to 0 by
hardware.
Bit 2
A2NS: A2N pin to OPA2 Inverting input control bit
0: no connection
1: from A2N pin
If this bit is set to 1, the A1O2A2N bit will be cleared to 0 by hardware.
112
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Bit 1
A2OEN: OPA2 output enable or disable control bit
0: disable
1: enable
Note: If OPA2 enable and A2OEN set to 1, the MCU will consumption more DC
power (100μA ~ 200μA).
Bit 0
A2EN: OPA2 enable or disable control bit
0: disable
1: enable
If this bit is set to 0, the PGAEN and A2O2N bits will be cleared to 0 by hardware.
OPA2C2 Register
Bit
Name
7
6
A1O2A2N A1O2A2P
5
4
3
2
1
0
—
—
PGAEN
PGA2
PGA1
PGA0
R/W
R/W
R/W
—
—
R/W
R/W
R/W
R/W
POR
0
0
—
—
0
0
0
0
Bit 7
A1O2A2N: OPA1 output to OPA2 Inverting input control bit
0: disable
1: enable
To select the OPA1 output as the OPA2 inverting input, the A2NS bit should first be
set to 0 followed by the A1O2A2N bit being set to 1.
Bit 6
A1O2A2P: OPA1 output to OPA2 Non-inverting input control bit
0: disable
1: enable
To select the OPA1 output as the OPA2 non-inverting input, the A2PS bit should first
be set to 0 followed by the A1O2A2N bit being set to 1.
Bit 5~4 unimplemented, read as “0”
Bit 3
PGAEN: OPA2 PGA gain enable control bits
0: disable
1: enable
Bit 2~0
PGA2, PGA1, PGA0: OPA2 Gain control bits
000: 1
001: 8
010: 16
011: 24
100: 32
101: 40
110: 48
111: 56
Operational Amplifier Operation
The advantages of multiple switches and input path options, various reference voltage selection, up
to 8 kinds of internal software gain control, offset reference voltage calibration function and power
down control for low power consumption enhance the flexibility of these two OPAs to suit a wide
range of application possibilities. The following block diagram illustrates the main functional blocks
of the OPAs and Comparator in the devices.
Rev. 1.00
113
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
A1O2N
Connect AN6 (A/D)
A1NS
A1N
A1P
VH1
VM
VL1
CINTO
A1
A1PS
CMPINT
CMPES[1:0]
MU
X
A1O2CIN
R1
10K
R2
PGAEN
CMP1X
C1
C1OUTEN
C1OUT
C1INTEN
C2INTEN
A2O2N
A2NS
C1N
C1NSEL
A1E
PGAEN
VH0
MUX
A1PSEL[1:0]
A2N
Edge Select
A1X
A1OEN
A2O2CIN
C2
CINTO
CMP2X
560K
C2OUTEN
C2OUT
A1O2A2N
A1O2A2P
MUX
A2
C2P
VL0
C2PSEL
A2P
A2PS
VH1
VM
VL1
CNPSEL
CNP
MUX
Connect AN7 (A/D)
A2PSEL[1:0]
A2OEN
A2E
A2X
Operational Amplifier Functions
The OPAs are connected together internally in a specific way and the output of OPAs can also be
connected to the internal comparators as shown in the block diagram. Each of the OPAs has its own
control register, with the name OPA1C0, OPA1C1, OPA2C0, OPA2C1 and OPA2C2 which are used
to control the enable/disable function, the calibration procedure and the programmable gain function
of OPA2.
OPA1 Switch Control
The following diagram and table illustrate the OPA1 switch control setting and the corresponding
connections. Note that some switch control selections will force some switches to be controlled by
hardware automatically.
For example:
• The S7C is closed when A1O2CIN=1 and the S7C is opened when A1O2CIN =0.
• The A1PS=1 will force A1PSEL1, 0=(00), i.e. S10C, S9C, S8C will be opened.
• When the A1EN=0, S6C switch are opened by hardware, then the related I/O pins can be used as
the other functions.
Rev. 1.00
114
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
S10C
VH1
S9C
VM
S8C
VL1
CMP1
A1O2N
A1O2C1N
S7C
S6C
CMP2
A1O2C2N
A1NS
A1N
OPA2
S5C
A1O2A2P
A1E
OPA1
A1PS
A1P
S4C
A1X
A1OEN
A1PS=1 will force A1PSEL[1:0]=00, i.e. S10C, S9C, S8C will be opened.
A1EN=0 will force the S6C opened by hardware, then the related I/O pins can be used as the other functions.
OPA1 Switch Control
The following table illustrates the relationship between OPA1 control register settings and the
switches:
OPA1 Control Bits in OPA1C0,
OPA1C1
A1PS A1NS
A1PSEL1
A1O2N
A1PSEL0
Switch Description
S4C
S5C
S6C
Results
S8C~
S10C
Off
OPA1 connections
1
1
00
0
On
On
Off
0
1
01
0
Off
On
Off
S10C On Input= A1N, VH1
Input= A1N, A1P
0
1
10
0
Off
On
Off
S9C On Input= A1N, VM
0
1
11
0
Off
On
Off
S8C On Input= A1N, VL1
1
1
00
1
On
On
On
Off
Input= A1N, A1P,
connect A1N, A1E
1
0
00
1
On
Off
On
Off
Input= A1P,
OPA1 as unit gain buffer
0
1
01
0
Off
On
Off
0
1
10
0
Off
On
Off
S10C On Input= A1N, VH1
S9C On Input= A1N, VM
0
1
11
0
Off
On
Off
S8C On Input= A1N, VL1
Note: The A1O2N bit is only available when the OPA1 is enabled by setting the A1EN bit high.
When the OPA1 is disabled by setting the A1EN bit low, the A1O2N bit will be forced low
and the S6C will be switched off by hardware.
The following table illustrates the OPA1 & I/O settings.
A1EN A1NS A1PS
Rev. 1.00
Description
0
x
x
PA2, PA3 and PA4 are I/Os
1
0
0
PA2 and PA3 are I/Os, PA4 is OPA1 A1E output
1
0
1
PA3 is I/O. PA2 is OPA1 A1P input, PA4 is OPA1 A1E output
1
1
0
PA2 is I/O. PA3 is OPA1 A1N input, PA4 is OPA1 A1E output
1
1
1
PA2 is OPA1 A1P input and PA3 is OPA1 A1N input, PA4 is OPA1 A1E output
115
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
OPA2 Switch Control
The following diagram and table illustrate the OPA2 switch control setting and the corresponding
connections. Note that some switch control selections will force some switches to be controlled by
hardware automatically.
For example:
• The PGAEN=1 will force S6D, S7D to close and the PGAEN=0 will force S6D, S7D to open.
• When the A2EN=0, these switches, S6D, S7D and S9D, are opened by hardware, then the related
I/O pins can be used as the other functions.
A1O2A2P
OPA1
S11D
S12D
S13D
S14D
A1O2A2N
S8D
A2N
S6D
VH1
VM
VL1
CMP1
A2O2CIN
A2O2N
S9D
560K
10K
CMP2
S10D
S7D
A2NS
S5D
A2E
OPA2
A2P
A2PS
S4D
A2X
Switch priority: S4D>S11D>(S12D, S13D, S14D); If A2PS=1, S11D~S14D will be opened by hardware.
Switch priority: S5D>S8D; If A2NS=1, S8D will be opened by hardware.
A2OEN
OPA2 Switch Control
Rev. 1.00
116
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
The following table illustrates the relationship between OPA2 control register settings and the
switches:
OPA2 Control Bits in OPA2C0, OPA2C1, OPA2C2
Switch Description
Results
A2PSEL1
S12D~
A2PS A2NS
A1O2A2P A1O2A2N PGAEN A2O2N S4D S5D S6/7D S8D S9D S11D
A2PSEL0
S14D
Off
OPA2
connections
Normal mode,
Input=A2N, A2P
1
1
00
0
0
0
0
On
On
Off
Off
Off
Off
0
1
01
0
0
0
0
Off
On
Off
Off
Off
Off
S12D
Input=A2N, VH1
On
0
1
10
0
0
0
0
Off
On
Off
Off
Off
Off
S13D
Input=A2N, VM
On
0
1
11
0
0
0
0
Off
On
Off
Off
Off
Off
S14D
Input=A2N, VL1
On
0
1
00
1
0
0
0
Off
On
Off
Off
Off
On
Off
Input=A2N, A1E
1
0
00
0
1
0
0
On
Off
Off
On
Off
Off
Off
Input=A1E, A2P
1
1
00
0
0
1
0
On
On
On
Off
Off
Off
Off
Input=A2N, A2P
1
0
00
0
0
1
0
On
Off
On
Off
Off
Off
Off
Input=A2N, A2P
1
0
00
0
0
0
1
On
Off
Off
Off
On
Off
Off
Input=A2P,
OPA2 as buffer
0
0
01
0
0
0
1
Off
Off
Off
Off
Off
Off
S12D Input=VH1,
On
OPA2 as buffer
0
0
10
0
0
0
1
Off
Off
Off
Off
Off
Off
S13D Input=VM,
On
OPA2 as buffer
0
0
11
0
0
0
1
Off
Off
Off
Off
Off
Off
S14D Input=VL1,
On
OPA2 as buffer
The following table illustrates the OPA2 & I/O settings.
A2EN PGAEN A2NS A2PS
Description
0
x
x
x
PA5 and PA6 and PA7 are I/Os
1
0
0
0
PA5 and PA6 are I/Os. PA7 is OPA2 A2E output
1
0
0
1
PA6 is I/O. PA5 is OPA2 A2P input, PA7 is OPA2 A2E output
1
0
1
0
PA5 is I/O. PA6 is OPA2 A2N input, PA7 is OPA2 A2E output
1
0
1
1
PA5 is OPA2 A2P input and PA6 is OPA2 A2N input, PA7 is OPA2 A2E output
1
1
0
0
PA5 is I/O. PA6 is OPA2 A2N input, PA7 is OPA2 A2E output
1
1
0
1
PA5 is OPA2 A2P input and PA6 is OPA2 A2N input, PA7 is OPA2 A2E output
1
1
1
0
PA5 is I/O. PA6 is OPA2 A2N input and bypass R1 (10kΩ), PA7 is OPA2 A2E output
1
1
1
1
PA5 is OPA2 A2P input and PA6 is OPA2 A2N input and bypass R1 (10kΩ), PA7 is
OPA2 A2E output
Rev. 1.00
117
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Comparators
Two analog comparators are contained within the devices. These functions offer flexibility via their
register controlled features such as power-down, interrupt etc. Sharing their pins with normal I/O
pins, the comparators do not waste precious I/O pins if there functions are otherwise unused. In
addition, the devices provide the calibration function to adjust the comparator offset.
Comparator Operation
The devices contain two comparator functions which are used to compare two analog voltages
and provide an output based on their difference. Full control over the two internal comparators
is provided via control registers, CMP1C0, CMP1C1, CMP2C0 and CMP2C1. The comparator
output is recorded via a bit in their respective control register, but can also be transferred out onto a
shared I/O pin or to generate an interrupt trigger with edge control function. Additional comparator
functions include the power down control.
Comparator Registers
The internal dual comparators are fully under the control of internal registers, CMP1C0, CMP1C1,
CMP2C0 and CMP2C1. These registers control enable/disable function, input path selection,
interrupt edge control and input offset voltage calibration function.
CMP1C0 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
CMP1X
C1OFM
C1RS
C1OF4
C1OF3
C1OF2
C1OF1
C1OF0
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
1
0
0
0
0
Bit 7
CMP1X: comparator output; positive logic. This bit is read only.
Bit 6
C1OFM: Comparator mode or input offset voltage cancellation mode
0: comparator mode
1: input offset voltage cancellation mode
When the C1OFM=1, comparator inputs are always from I/O pins. i.e. the CNPSEL
and C1NSEL will be forced to “1”. That means disconnect the input from OPAs
output.
Bit 5
C1RS: Comparator input offset voltage cancellation reference selection bit
0: select C1N as the reference input
1: select CNP as the reference input
Note: The C1N is not connected to the external pin and internally used only.
Bit 4~0
C1OF4~C1OF0: Comparator input offset voltage cancellation control bits
118
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
CMP1C1 Register
Bit
7
6
5
4
Name
CNPSEL
—
—
—
R/W
R/W
—
—
—
R/W
R/W
R/W
R/W
POR
1
—
—
—
0
0
1
0
Bit 7
3
2
1
0
C1INTEN C1OUTEN C1NSEL CMP1EN
CNPSEL: Comparator non-inverting input control bit
0: from OPA output
1: from CNP pin
Bit 6~4
unimplemented, read as “0”
Bit 3
C1INTEN: Comparator 1 interrupt control bit
0: disable
1: enable
Bit 2
C1OUTEN: Comparator 1 output pin control bit
0: disable
1: enable
Bit 1
C1NSEL: Comparator 1 inverting input control bit
0: from VH0
1: from C1N pin
Note: The C1N is not connected to the external pin and internally used only.
Bit 0
CMP1EN: Comparator 1 enable or disable control bit
0: disable
1: enable
CMP2C0 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
CMP2X
C2OFM
C2RS
C2OF4
C2OF3
C2OF2
C2OF1
C2OF0
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
1
0
0
0
0
Bit 7
CMP2X: comparator output; positive logic. This bit is read only.
Bit 6
C2OFM: Comparator mode or input offset voltage cancellation mode
0: comparator mode
1: input offset voltage cancellation mode
When the C2OFM=1, comparator inputs are always from I/O pins. i.e. the CNPSEL
and C1NSEL will be forced to “1”. That means disconnect the input from OPAs
output.
Bit 5
C2RS: Operational amplifier input offset voltage cancellation reference selection bit
0: select C2P as the reference input
1: select CNP as the reference input
Note: The C2P is not connected to the external pin and internally used only.
Bit 4~0
C2OF4~C2OF0: Comparator input offset voltage cancellation control bits
119
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
CMP2C1 Register
Bit
7
Name
6
CMPES1 CMPES0
5
4
—
—
3
2
1
0
C2INTEN C2OUTEN C2PSEL CMP2EN
R/W
R/W
R/W
—
—
R/W
R/W
R/W
R/W
POR
0
0
—
—
0
0
1
0
Bit 7~6
CMPES1, CMPES0: Interrupt edge control bits
00: disable
01: rising edge trigger
10: falling edge trigger
11: dual edge trigger
Bit 5~4
unimplemented, read as “0”
Bit 3
C2INTEN: Comparator 2 interrupt control bit
0: disable
1: enable
Bit 2
C2OUTEN: Comparator 2 output pin control bit
0: disable
1: enable
Bit 1
C2PSEL: Comparator 2 non-inverting input control bit
0: from VL0
1: from C2P pin
Note: The C2P is not connected to the external pin and internally used only.
Bit 0
CMP2EN: Comparator 2 enable or disable control bit
0: disable
1: enable
Comparator Functions
These two comparators can operate together with the OPAs or standalone as shown in the main
functional blocks of the OPAs and Comparators.
Each of the internal comparators in the devices allows for a common mode adjustment method of its
input offset voltage.
The calibration steps are as following:
1. Set C1OFM=1 to setup the offset cancellation mode, here S3A is closed.
2. Set C1RS to select which input pin is to be used as the reference voltage – S1A or S2A is closed.
3. Adjust C1OF0~C1OF4 until the output status changes.
4. Set C1OFM = 0 to restore the normal comparator mode.
5. Repeat the same procedure from steps 1 to 4 for comparator 2.
C1OFM
0
C1RS
x
1
0
1
1
"x" : don´t care
S1A
S2A
ON
OFF
ON
ON
ON
S3A
OFF
ON
OFF
ON
S2A
C1OUTEN
C1N
CNP
Rev. 1.00
S3A
C1OUT
CMP1
S1A
CMP1X
120
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
The following diagram and table illustrate the comparators switch control setting and the
corresponding connections. Note that some switch control selections will force some switches to be
controlled by hardware automatically.
For example:
• When the CMP1 in calibration mode, i.e. C1OFM =1, then the SW1, SW3 will be forced to
close. The CNPSEL and C1NSEL bits will be set “1” by hardware, and these two bits will be
read out as “1”. After the offset voltage calibration, the CNPSEL and C1NSEL will be back to its
original value.
• When the CMP2 in calibration mode, i.e. C2OFM =1, then the SW1, SW2 will be forced to
close. The CNPSEL and C2PSEL bits will be set “1” by hardware, and these two bits will be
read out as “1”. After the offset voltage calibration, the CNPSEL and C2PSEL will be back to its
original value.
• If the CNPSEL=1, the A1O2CIN and A2O2CIN will be forced to “0”, i.e. If the SW1 is closed,
and that will force S7C and S10D to open.
• If the CNPSEL=0 and the A1O2CIN=1, the A2O2CIN will be forced to “0”, i.e. If the S7C is
closed, and that will force S10D to open.
CNP
C1N
C2P
SW1
SW2
CNPSEL
Edge Select
CINT0
VH0
VL0
SW3
C2PSEL
CMPINT
CMPES1, CMPES0
C1NSEL
C1OUTEN
S2A
CMP1
A1O2CIN
OPA1
S3A
C1INTEN
S10D
S2B
C2OUT
CMP2
S1B
C1OUT
CINT0
C2INTEN
S7C
A2O2CIN
OPA2
S1A
CMP1X
CMP2X
C2OUTEN
S3B
Comparators Switch Control
Rev. 1.00
121
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
The following table illustrates the CMP1 & I/O settings.
CMP1EN C1OUTEN CNPSEL C1NSEL
Description
0
x
x
x
PC5 and PA0 and PA1 are I/Os
1
0
0
0
CNP is from OPA1 or OPA2 output, C1N is from VH0 input, PA1 is I/O
1
0
0
1
CNP is from OPA1 or OPA2 output, C1N is from PC5 input, PA1 is I/O
1
0
1
0
CNP is from PA0 input, C1N is from VH0 input, PA1 is I/O
1
0
1
1
CNP is from PA0 input, C1N is from PC5 input, PA1 is I/O
1
1
0
0
CNP is from OPA1 or OPA2 output, C1N is from VH0 input, PA1 is
comparator output
1
1
0
1
CNP is from OPA1 or OPA2 output, C1N is from PC5 input, PA1 is
comparator output
1
1
1
0
CNP is from PA0 input, C1N is from VH0 input, PA1 is comparator output
1
1
1
1
CNP is from PA0 input, C1N is from PC5 input, PA1 is comparator output
The following table illustrates the CMP2 & I/O settings.
CMP2EN C2OUTEN CNPSEL C2PSEL
Description
0
x
x
x
PC6 and PA0 and PA2 are I/Os
1
0
0
0
CNP is from OPA1 or OPA2 output, C2P is from VL0 input, PA2 is I/O
1
0
0
1
CNP is from OPA1 or OPA2 output, C2P is from PC6 input, PA2 is I/O
1
0
1
0
CNP is from PA0 input, C2P is from VL0 input, PA2 is I/O
1
0
1
1
CNP is from PA0 input, C2P is from PC6 input, PA2 is I/O
1
1
0
0
CNP is from OPA1 or OPA2 output, C2P is from VL0 input, PA2 is
comparator output
1
1
0
1
CNP is from OPA1 or OPA2 output, C2P is from PC6 input, PA2 is
comparator output
1
1
1
0
CNP is from PA0 input, C2P is from VL0 input, PA2 is comparator output
1
1
1
1
CNP is from PA0 input, C2P is from PC6 input, PA2 is comparator output
The following table illustrates the relationship between comparators control register settings and the
switches:
CMP1,CMP2 Control Bits
Switch Description
Results
CNPSEL
C2PSEL
C1NSEL
C1OFM C1RS SW1 SW2 SW3 S1A S2A S3A S7C S10D
1
(Forced to 1)
x
1
(Forced to 1)
1
1
ON
CNP
x
ON
C1N
ON
OFF
ON
OFF
OFF Input common mode=CNP
1
(Forced to 1)
x
1
(Forced to 1)
1
0
ON
CNP
x
ON
OFF
C1N
ON
ON
OFF
OFF Input common mode=C1N
1
0
1
0
x
ON
x
C1N
ON
ON
OFF OFF
OFF Input = CNP, C1N
1
0
0
0
x
ON
x
VH
ON
ON
OFF OFF
OFF Input = CNP, VH1
0
0
1
0
x
OFF
x
C1N
ON
ON
OFF
OFF Input = A1E, C1N
0
0
1
0
x
OFF
x
C1N
ON
ON
OFF OFF
ON
ON
Connections
Input = A2E, C1N
Comparators Switch Control
Rev. 1.00
122
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Interrupts
Interrupts are an important part of any microcontroller system. When an external event or an
internal function such as a Timer/Event Counter or an A/D converter requires microcontroller
attention, their corresponding interrupt will enforce a temporary suspension of the main program
allowing the microcontroller to direct attention to their respective needs.The devices contain several
external interrupt and internal interrupts functions. The external interrupts are controlled by the
action of the external INT0, INT1 and PINT pins, while the internal interrupts are controlled by the
Timer/Event Counter overflows, the Time Base interrupts, the SIM interrupt, the A/D converter
interrupt,Comparator interrupt, EEPROM interrupt and LVD interrupt.
Interrupt Register
Overall interrupt control, which means interrupt enabling and request flag setting, is controlled
by the INTC0, INTC1, MFIC0 and MFIC1 registers, which are located in the Data Memory. By
controlling the appropriate enable bits in these registers each individual interrupt can be enabled
or disabled. Also when an interrupt occurs, the corresponding request flag will be set by the
microcontroller. The global enable flag if cleared to zero will disable all interrupts.
Interrupt Operation
A Timer/Event Counter overflow, Time Base 0/1, SIM data transfer complete, an end of A/D
conversion, the external interrupt line being triggered, a comparator output, an EEPROM Write
or Read cycle ends, or a LVD detection will all generate an interrupt request by setting their
corresponding request flag, if their appropriate interrupt enable bit is set. When this happens, the
Program Counter, which stores the address of the next instruction to be executed, will be transferred
onto the stack. The Program Counter will then be loaded with a new address which will be the value
of the corresponding interrupt vector. The microcontroller will then fetch its next instruction from
this interrupt vector. The instruction at this vector will usually be a JMP statement which will jump
to another section of program which is known as the interrupt service routine. Here is located the
code to control the appropriate interrupt. The interrupt service routine must be terminated with a
RETI statement, which retrieves the original Program Counter address from the stack and allows the
microcontroller to continue with normal execution at the point where the interrupt occurred.
The various interrupt enable bits, together with their associated request flags, are shown in the
accompanying diagram with their order of priority.
Once an interrupt subroutine is serviced, all the other interrupts will be blocked, as the EMI bit will
be cleared automatically. This will prevent any further interrupt nesting from occurring. However,
if other interrupt requests occur during this interval, although the interrupt will not be immediately
serviced, the request flag will still be recorded. If an interrupt requires immediate servicing while the
program is already in another interrupt service routine, the EMI bit should be set after entering the
routine, to allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged,
even if the related interrupt is enabled, until the Stack Pointer is decremented. If immediate service
is desired, the stack must be prevented from becoming full.
Rev. 1.00
123
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Interrupt Priority
Interrupts, occurring in the interval between the rising edges of two consecutive T2 pulses, will be
serviced on the latter of the two T2 pulses, if the corresponding interrupts are enabled. In case of
simultaneous requests, the following table shows the priority that is applied.
Priority
Vector
External interrupt 0
Interrupt Source
1
04H
External interrupt 1
2
08H
Timer/Event Counter 0 overflow
3
0CH
Timer/Event Counter 1 overflow
4
10H
SPI/I2C interrupt
5
14H
Multi-function Interrupt
6
18H
The A/D converter interrupt, Time Base interrupt, External Peripheral interrupt, Comparator
interrupt, EEPROM interrupt, and LVD interrupt all share the same interrupt vector which is 18H.
Each of these interrupts has their own individual interrupt flag but also share the same MFF interrupt
flag.
The MFF flag will be cleared by hardware once the Multi-function interrupt is serviced, however the
individual interrupts that have triggered the Multi-function interrupt need to be cleared by the
application program.
INTC0 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
—
T0F
EIF1
EIF0
ET0I
EEI1
EEI0
EMI
R/W
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
—
0
0
0
0
0
0
0
Bit 7
unimplemented, read as “0”
Bit 6
T0F: Timer/Event Counter 0 interrupt request flag
0: inactive
1: active
Bit 5
EIF1: External interrupt 1 request flag
0: inactive
1: active
Note: The INT1 is not connected to the external pin and internally used only.
Bit 4
EIF0: External interrupt 0 request flag
0: inactive
1: active
Bit 3
ET0I: Timer/Event Counter 0 interrupt enable
0: disable
1: enable
Bit 2
EEI1: External interrupt 1 enable
0: disable
1: enable
Note: The INT1 is not connected to the external pin and internally used only.
Bit 1
EEI0: External interrupt 0 enable
0: disable
1: enable
Bit 0
EMI: Master interrupt global enable
0: disable
1: enable
124
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
INTC1 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
—
MFF
SIMF
T1F
—
EMFI
ESIM
ET1I
R/W
—
R/W
R/W
R/W
—
R/W
R/W
R/W
POR
—
0
0
0
—
0
0
0
Bit 7
unimplemented, read as “0”
Bit 6
MFF: Multi-function interrupt request flag
0: inactive
1: active
Bit 5
SIMF: SIM interrupt request flag
0: inactive
1: active
Note: The SIM pins are not connected to the external pins and internally used only.
Bit 4
TIF: Timer/Event counter 1 interrupt request flag
0: inactive
1: active
Bit 3
unimplemented, read as “0”
Bit 2
EMFI: Multi-function interrupt enable
0: disable
1: enable
Bit 1
ESIM: SIM interrupt enable
0: disable
1: enable
Note: The SIM pins are not connected to the external pins and internally used only.
Bit 0
ET1I: Timer/Event counter 1 interrupt enable
0: disable
1: enable
125
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
MFIC0 Register
Rev. 1.00
Bit
7
6
5
4
3
2
1
0
Name
PEF
TB1F
TB0F
ADF
EPI
TB1E
TB0E
EADI
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7
PEF: External peripheral interrupt request flag
0: inactive
1: active
Note: The PINT is not connected to the external pin.
Bit 6
TB1F: Time Base 1 interrupt request flag
0: inactive
1: active
Bit 5
TB0F: Time Base 0 interrupt request flag
0: inactive
1: active
Bit 4
ADF: A/D converter interrupt request flag
0: inactive
1: active
Bit 3
EPI: External peripheral interrupt enable
0: disable
1: enable
Note: The PINT is not connected to the external pin.
Bit 2
TB1E: Time Base 1 enable
0: disable
1: enable
Bit 1
TB0E: Time Base 0 enable
0: disable
1: enable
Bit 0
EADI: A/D converter interrupt enable
0: disable
1: enable
126
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
MFIC1 Register
Bit
7
6
5
4
3
2
1
0
Name
—
LVDF
E2F
CF
—
ELVDI
EE2I
ECI
R/W
—
R/W
R/W
R/W
—
R/W
R/W
R/W
POR
—
0
0
0
—
0
0
0
Bit 7
unimplemented, read as “0”
Bit 6
LVDF: LVD interrupt request flag
0: inactive
1: active
Bit 5
E2F: EEPROM interrupt request flag
0: inactive
1: active
Bit 4
CF: Comparator interrupt request flag
0: inactive
1: active
Bit 3
unimplemented, read as “0”
Bit 2
ELVDI: LVD interrupt enable
0: disable
1: enable
Bit 1
EE2I: EEPROM interrupt enable
0: disable
1: enable
Bit 0
ECI: Comparator interrupt enable
0: disable
1: enable
External Interrupt
The external interrupts are controlled by signal transitions on the pins INT0~INT1. An external
interrupt request will take place when the external interrupt request flags, EIF0~EIF1, are set, which
will occur when a transition, whose type is chosen by the edge select bits, appears on the external
interrupt pins. To allow the program to branch to its respective interrupt vector address, the global
interrupt enable bit, EMI, and respective external interrupt enable bit, EEI0~EEI1, must first be
set. Additionally the correct interrupt edge type must be selected using the INTEDGE register to
enable the external interrupt function and to choose the trigger edge type. As the external interrupt
pins are pin-shared with I/O pins, they can only be configured as external interrupt pins if their
external interrupt enable bit in the corresponding interrupt register has been set. The pin must also
be setup as an input by setting the corresponding bit in the port control register. When the interrupt
is enabled, the stack is not full and the correct transition type appears on the external interrupt pin,
a subroutine call to the external interrupt vector, will take place. When the interrupt is serviced,
the external interrupt request flags, EIF0~EIF1, will be automatically reset and the EMI bit will be
automatically cleared to disable other interrupts. Note that any pull-high resistor selections on the
external interrupt pins will remain valid even if the pin is used as an external interrupt input.
The INTEDGE register is used to select the type of active edge that will trigger the external
interrupt. A choice of either rising or falling or both edge types can be chosen to trigger an external
interrupt. Note that the INTEDGE register can also be used to disable the external interrupt function.
Rev. 1.00
127
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Note: The INTC1 is not connected to the external pin and internally used only.
EMI auto disa�led in ISR
Legend
xxF
Request Flag -no auto �eset in ISR
xxF
Request Flag-auto �eset in ISR
xxE
Ena�le Bit
Inte��upt
�a�e
A/D
Ti�e Base 0
Ti�e Base 1
Request
Flags
Ena�le
Bits
ADF
EADI
TB0F
TB0E
TB1F
TB1E
PI�T
PEF
EPI
Co�pa�ato�
CF
ECI
EEPROM
E�F
EE�I
LVDF
ELVDI
Inte��upt
�a�e
Request
Flags
Ena�le
Bits
Maste�
Ena�le
Vector
I�T0
EIF0
EEI0
EMI
0�H
I�T1
EIF1
EEI1
EMI
08H
Ti�e�/Event
Counte�0
T0F
ET0I
EMI
0CH
Ti�e�/Event
Counte�1
T1F
ET1I
EMI
10H
SIM
SIMF
ESIM
EMI
1�H
M.Funct .
MFF
EMFI
EMI
18H
P�io�ity
High
Low
LVD
Inte��upts contained within
Multi-Function Inte��upts
Interrupt Structure
The external interrupt pins are connected to an internal filter to reduce the possibility of unwanted
external interrupts due to adverse noise or spikes on the external interrupt input signal. As this
internal filter circuit will consume a limited amount of power, a configuration option is provided
to switch off the filter function, an option which may be beneficial in power sensitive applications,
but in which the integrity of the input signal is high. Care must be taken when using the filter on/off
configuration option as it will be applied not only to both the external interrupt pins but also to the
Timer/Event Counter external input pins. Individual external interrupt or Timer/Event Counter pins
cannot be selected to have a filter on/off function.
Rev. 1.00
128
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
INTEDGE Register
Bit
7
6
5
4
3
2
1
0
Name
—
—
—
—
INT1S1
INT1S0
INT0S1
INT0S0
R/W
—
—
—
—
R/W
R/W
R/W
R/W
POR
—
—
—
—
0
0
0
0
Bit 7~4
unimplemented, read as “0”
Bit 3~2
INT1S1, INT1S0: INT1 Edge select
00: disable
01: rising edge trigger
10: falling edge trigger
11: dual edge trigger
Bit 1~0
INT0S1, INT0S0: INT0 Edge select
00: disable
01: rising edge trigger
10: falling edge trigger
11: dual edge trigger
External Peripheral Interrupt
The External Peripheral Interrupt operates in a similar way to the external interrupt and is contained
within the Multi-function interrupt.
For an external peripheral interrupt to occur, the global interrupt enable bit, EMI, external peripheral
interrupt enable bit, EPI, and Multi-function interrupt enable bit, EMFI, must first be set. An actual
external peripheral interrupt will take place when the external interrupt request flag, PEF, is set, a
situation that will occur when a negative transition, appears on the PINT pin. The external peripheral
interrupt pin is pin-shared with the I/O pin PB5, and is configured as a peripheral interrupt pin via
a configuration option. When the interrupt is enabled, the stack is not full and a negative transition
type appears on the external peripheral interrupt pin, a subroutine call to the Multi-function interrupt
vector at location18H, will take place. When the external peripheral interrupt is serviced, the EMI
bit will be cleared to disable other interrupts, however only the MFF interrupt request flag will be
reset. As the PEF flag will not be automatically reset, it has to be cleared by the application program.
Note: The PINT is not connected to the external pin and internally used only.
Timer/Event Counter Interrupt
For a Timer/Event Counter interrupt to occur, the global interrupt enable bit, EMI, and the
corresponding timer interrupt enable bit, ET0I or ET1I, must first be set. An actual Timer/Event
Counter interrupt will take place when the Timer/Event Counter request flag, T0F or T1F, is set, a
situation that will occur when the Timer/Event Counter overflows. When the interrupt is enabled, the
stack is not full and a Timer/Event Counter overflow occurs, a subroutine call to the timer interrupt
vector at location 0CH or 10H, will take place. When the interrupt is serviced, the timer interrupt
request flag, T0F or T1F, will be automatically reset and the EMI bit will be automatically cleared to
disable other interrupts.
Rev. 1.00
129
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
SIM Interface Interrupt
For an SIM interrupt to occur, the global interrupt enable bit, EMI, and the corresponding interrupt
enable bit, ESIM must be first set. An actual SIM interrupt will take place when the SIM interface
request flag, SIMF, is set, a situation that will occur when a byte of data has been transmitted or
received by the SIM interface When the interrupt is enabled, the stack is not full and a byte of data
has been transmitted or received by the SIM interface, a subroutine call to the SIM interrupt vector
at location 14H, will take place. When the interrupt is serviced, the SIM request flag, SIMF will be
automatically reset and the EMI bit will be automatically cleared to disable other interrupts.
Note: The SIM pins is not connected to the external pin and internally used only.
Multi-function Interrupt
An additional interrupt known as the Multi-function interrupt is provided. Unlike the other
interrupts, this interrupt has no independent source, but rather is formed from four other existing
interrupt sources, namely the A/D Converter interrupt, Time Base interrupts, the External Peripheral
interrupt, Comparator interrupt, EEPROM interrupt and LVD interrupt.
For a Multi-function interrupt to occur, the global interrupt enable bit, EMI, and the Multi-function
interrupt enable bit, EMFI, must first be set. An actual Multi-function interrupt will take place when
the Multi-function interrupt request flag, MFF, is set. This will occur when either a Time Base
overflow, an A/D conversion completion, an External Peripheral Interrupt, a Comparator output
interrupt, an EEPROM Write or Read cycle ends interrupt, or a LVD interrupt is generated. When
the interrupt is enabled and the stack is not full, and either one of the interrupts contained within the
Multi-function interrupt occurs, a subroutine call to the Multi-function interrupt vector at location
018H will take place. When the interrupt is serviced, the Multi-Function request flag, MFF, will
be automatically reset and the EMI bit will be automatically cleared to disable other interrupts.
However, it must be noted that the request flags from the original source of the Multi-function
interrupt, namely the Time-Base interrupt, A/D Converter interrupt, Comparator interrupt,EEPROM
interrupt,LVD interrupt or External Peripheral interrupt will not be automatically reset and must be
manually reset by the application program.
A/D Interrupt
The A/D Interrupt is contained within the Multi-function Interrupt.
For an A/D Interrupt to be generated, the global interrupt enable bit, EMI, A/D Interrupt enable
bit, EADI, and Multi-function interrupt enable bit, EMFI, must first be set. An actual A/D Interrupt
will take place when the A/D Interrupt request flag, ADF, is set, a situation that will occur when
the A/D conversion process has finished. When the interrupt is enabled, the stack is not full and
the A/D conversion process has ended, a subroutine call to the Multi-function interrupt vector at
location18H, will take place. When the A/D Interrupt is serviced, the EMI bit will be cleared to
disable other interrupts, however only the MFF interrupt request flag will be reset. As the ADF flag
will not be automatically reset, it has to be cleared by the application program.
Rev. 1.00
130
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Time Base Interrupt
The function of the Time Base Interrupts is to provide regular time signal in the form of an internal
interrupt. They are controlled by the overflow signals from their respective timer functions. When
these happens their respective interrupt request flags, TB0F or TB1F will be set. To allow the
program to branch to their respective interrupt vector addresses, the global interrupt enable bit, EMI
and Time Base enable bits, TB0E or TB1E, must first be set. When the interrupt is enabled, the stack
is not full and the Time Base overflows, a subroutine call to their respective vector locations will
take place. When the interrupt is serviced, the respective interrupt request flag, TB0F or TB1F, will
be automatically reset and the EMI bit will be cleared to disable other interrupts.
The purpose of the Time Base Interrupt is to provide an interrupt signal at fixed time periods. Their
clock sources originate from the internal clock source fTB. This fTB input clock passes through a
divider, the division ratio of which is selected by programming the appropriate bits in the TBC
register to obtain longer interrupt periods whose value ranges. The clock source that generates fTB,
which in turn controls the Time Base interrupt period, can originate from several different sources,
as shown in the System Operating Mode section.
     
    
  
Time Base Interrupt
TBC Register
Bit
7
6
5
4
3
2
1
0
Name
TBON
TBCK
TB11
TB10
LXTLP
TB02
TB01
TB00
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7
Bit 6
Bit 5~4
Bit 3
Bit 2~0
Rev. 1.00
TBON: TB0 and TB1 Control
0: disable
1: enable
TBCK: Select fTB Clock
0: fTBC
1: fSYS/4
TB11~TB10: Select Time Base 1 Time-out Period
00: 4096/fTB
01: 8192/fTB
10: 16384/fTB
11: 32768/fTB
LXTLP: LXT Low Power Control
0: disable
1: enable
TB02~TB00: Select Time Base 0 Time-out Period
000: 256/fTB
001: 512/fTB
010: 1024/fTB
011: 2048/fTB
100: 4096/fTB
101: 8192/fTB
110: 16384/fTB
111: 32768/fTB
131
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Comparator Interrupt
The Comparator Interrupt is contained within the Multi-function Interrupt.
The comparator interrupt is controlled by the two internal comparators. A comparator interrupt
request will take place when the comparator interrupt request flag, CF, is set, a situation that will
occur when the comparator output changes state. To allow the program to branch to its respective
interrupt vector address, the global interrupt enable bit, EMI, and comparator interrupt enable bit,
ECI, must first be set. When the interrupt is enabled, the stack is not full and the comparator input
generates a comparator output transition, a subroutine call to the comparator interrupt vector, will
take place. When the Comparator Interrupt is serviced, the EMI bit will be automatically cleared
to disable other interrupts, however only the Multi-function interrupt request flag will be also
automatically cleared. As the CF flag will not be automatically cleared, it has to be cleared by the
application program.
EEPROM Interrupt
The EEPROM Interrupt is contained within the Multi-function Interrupt. An EEPROM Interrupt
request will take place when the EEPROM Interrupt request flag, E2F, is set, which occurs when an
EEPROM Write or Read cycle ends. To allow the program to branch to its respective interrupt vector
address, the global interrupt enable bit, EMI, EEPROM Interrupt enable bit, EE2I, and associated
Multi-function interrupt enable bit, must first be set. When the interrupt is enabled, the stack is not
full and an EEPROM Write or Read cycle ends, a subroutine call to the respective Multi-function
Interrupt vector, will take place. When the EEPROM Interrupt is serviced, the EMI bit will be
automatically cleared to disable other interrupts, however only the Multi-function interrupt request
flag will be also automatically cleared. As the E2F flag will not be automatically cleared, it has to be
cleared by the application program.
LVD Interrupt
The Low Voltage Detector Interrupt is contained within the Multi-function Interrupt. An LVD
Interrupt request will take place when the LVD Interrupt request flag, LVDF, is set, which occurs
when the Low Voltage Detector function detects a low power supply voltage. To allow the program
to branch to its respective interrupt vector address, the global interrupt enable bit, EMI, Low Voltage
Interrupt enable bit, ELVDI, and associated Multi-function interrupt enable bit, must first be set.
When the interrupt is enabled, the stack is not full and a low voltage condition occurs, a subroutine
call to the Multi-function Interrupt vector, will take place. When the Low Voltage Interrupt is
serviced, the EMI bit will be automatically cleared to disable other interrupts, however only the
Multi-function interrupt request flag will be also automatically cleared. As the LVDF flag will not be
automatically cleared, it has to be cleared by the application program.
Interrupt Wake-up Function
Each of the interrupt functions has the capability of waking up the microcontroller when in the
SLEEP or IDLE Mode. A wake-up is generated when an interrupt request flag changes from low
to high and is independent of whether the interrupt is enabled or not. Therefore, even though the
devices are in the SLEEP or IDLE Mode and its system oscillator stopped, situations such as
external edge transitions on the external interrupt pins, a low power supply voltage or comparator
input change may cause their respective interrupt flag to be set high and consequently generate
an interrupt. Care must therefore be taken if spurious wake-up situations are to be avoided. If an
interrupt wake-up function is to be disabled then the corresponding interrupt request flag should be
set high before the devices enter the SLEEP or IDLE Mode. The interrupt enable bits have no effect
on the interrupt wake-up function.
Rev. 1.00
132
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Programming Considerations
By disabling the interrupt enable bits, a requested interrupt can be prevented from being serviced,
however, once an interrupt request flag is set, it will remain in this condition in the INTC0,
INTC1,MFIC0 and MFIC1 registers until the corresponding interrupt is serviced or until the request
flag is cleared by the application program.
It is recommended that programs do not use the “CALL Subroutine” instruction within the interrupt
subroutine. Interrupts often occur in an unpredictable manner or need to be serviced immediately
in some applications. If only one stack is left and the interrupt is not well controlled, the original
control sequence will be damaged once a “CALL subroutine” is executed in the interrupt subroutine.
All of these interrupts have the capability of waking up the processor when in the Power Down
Mode. Only the Program Counter is pushed onto the stack. If the contents of the status or other
registers are altered by the interrupt service program, which may corrupt the desired control
sequence, then the contents should be saved in advance.
Buzzer
Operating in a similar way to the Programmable Frequency Divider, the Buzzer function provides
a means of producing a variable frequency output, suitable for applications such as Piezo-buzzer
driving or other external circuits that require a precise frequency generator. The BZ and BZ pins
form a complimentary pair, and are pin-shared with I/O pins, PA6 and PA7. A BPCTL register is
used to select from one of three buzzer options. The first option is for both pins PA6 and PA7 to be
used as normal I/Os, the second option is for both pins to be configured as BZ and BZ buzzer pins,
the third option selects only the PA6 pin to be used as a BZ buzzer pin with the PA7 pin retaining its
normal I/O pin function. Note that the BZ pin is the inverse of the BZ pin which together generate a
differential output which can supply more power to connected interfaces such as buzzers.
The buzzer is driven by the internal clock source, fTB, which then passes through a divider, the
division ratio of which is selected by BPCTL register to provide a range of buzzer frequencies from
fTB/22 to fTB/29. The clock source that generates fTB, which in turn controls the buzzer frequency,
can originate from three different sources, the LXT oscillator, the LIRC oscillator or the System
oscillator/4, the choice of which is determined by the fTB clock source option. Note that the buzzer
frequency is controlled by BPCTL register, which select the source clock for the internal clock fTB.
  
 ­ 
€ ‚ 
 

ƒ Buzzer Function
If the BPCTL options have selected both pins PA6 and PA7 to function as a BZ and BZ
complementary pair of buzzer outputs, then for correct buzzer operation it is essential that both pins
must be setup as outputs by setting bits PAC6 and PAC7 of the PAC port control register to zero.
The PA6 data bit in the PA data register must also be set high to enable the buzzer outputs, if set low,
both pins PA6 and PA7 will remain low. In this way the single bit PA6 of the PA register can be used
as an on/off control for both the BZ and BZ buzzer pin outputs. Note that the PA7 data bit in the PA
register has no control over the BZ buzzer pin PA7.
Rev. 1.00
133
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
BPCTL Register
Bit
7
Name
6
5
PMODE PWM1EN PWM0EN
4
3
2
1
0
BC1
BC0
BZ2
BZ1
BZ0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~5
PWM control bits
Bit 4~3
BC1~BC0: Buzzer or I/O
00: PA7 is I/O, PA6 is I/O
01: PA7 is I/O, PA6 is BZ
10: reserved
11: PA7 is BZ, PA6 is BZ
Bit 2~0
BZ2~BZ0: Buzzer output frequency selection
000: fTB/22
001: fTB/23
010: fTB/24
011: fTB/25
100: fTB/26
101: fTB/27
110: fTB/28
111: fTB/29
PA6/PA7 Pin Function Control
PAC Register
PAC6
PAC Register
PAC7
PA Data Register PA Data Register
PA6
PA7
Output
Function
0
0
1
×
PA6=BZ; PA7=BZ
0
0
0
×
PA6=“0”; PA7=“0”
0
1
1
×
PA6=BZ
PA7=input line
0
1
0
×
PA6=“0”
PA7=input line
1
0
×
D
PA6=input line
PA7= D
1
1
×
×
PA6=input line
PA7=input line
“x” stands for don’t care; “D” stands for Data “0” or “1”
If the options have selected that only the PA6 pin is to function as a BZ buzzer pin, then the PA7 pin
can be used as a normal I/O pin. For the PA6 pin to function as a BZ buzzer pin, PA6 must be setup
as an output by setting bit PAC6 of the PAC port control register to zero. The PA6 data bit in the PA
data register must also be set high to enable the buzzer output, if set low pin PA6 will remain low. In
this way the PA6 bit can be used as an on/off control for the BZ buzzer pin PA6. If the PAC6 bit of
the PAC port control register is set high, then pin PA6 can still be used as an input even though the
option has configured it as a BZ buzzer output.
Note that no matter what BPCTL option is chosen for the buzzer, if the port control register has
setup the pin to function as an input, then this will override the BPCTL option selection and force
the pin to always behave as an input pin. This arrangement enables the pin to be used as both a
buzzer pin and as an input pin, so regardless of the BPCTL option chosen; the actual function of the
pin can be changed dynamically by the application program by programming the appropriate port
control register bit.
Rev. 1.00
134
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Buzzer Output Pin Control
Note: The above drawing shows the situation where both pins PA6 and PA7 are selected by BPCTL
option to be BZ and BZ buzzer pin outputs. The Port Control Register of both pins must have
already been setup as output. The data setup on pin PA7 has no effect on the buzzer outputs.
Low Voltage Detector – LVD
The devices have Low Voltage Detector function, also known as LVD. This enabled the devices to
monitor the power supply voltage, VDD, and provide a warning signal should it fall below a certain
level. This function may be especially useful in battery applications where the supply voltage will
gradually reduce as the battery ages, as it allows an early warning battery low signal to be generated.
The Low Voltage Detector also has the capability of generating an interrupt signal.
LVD Register
The Low Voltage Detector function is controlled using a single register with the name LVDC. Three
bits in this register, VLVD2~VLVD0, are used to select one of eight fixed voltages below which a
low voltage condition will be detemined. A low voltage condition is indicated when the LVDO bit is
set. If the LVDO bit is low, this indicates that the VDD voltage is above the preset low voltage value.
The LVDEN bit is used to control the overall on/off function of the low voltage detector. Setting the
bit high will enable the low voltage detector. Clearing the bit to zero will switch off the internal low
voltage detector circuits. As the low voltage detector will consume a certain amount of power, it may
be desirable to switch off the circuit when not in use, an important consideration in power sensitive
battery powered applications.
Rev. 1.00
135
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
LVDC Register
Bit
7
6
5
4
3
2
1
0
Name
—
—
LVDO
LVDEN
—
VLVD2
VLVD1
VLVD0
R/W
—
—
R
R/W
—
R/W
R/W
R/W
POR
—
—
0
0
—
0
0
0
Bit 7~6
unimplemented, read as “0”
Bit 5
LVDO: LVD Output Flag
0: no Low Voltage Detect
1: low Voltage Detect
Bit 4
LVDEN: Low Voltage Detector Control
0: disable
1: enable
Bit 3
unimplemented, read as “0”
Bit 2~0
LVD2~LVD0: Select LVD Voltage
000: 2.0V
001: 2.2V
010: 2.4V
011: 2.7V
100: 3.0V
101: 3.3V
110: 3.6V
111: 4.4V
LVD Operation
The Low Voltage Detector function operates by comparing the power supply voltage, VDD, with a
pre-specified voltage level stored in the LVDC register. This has a range of between 2.0V and 4.4V.
When the power supply voltage, VDD, falls below this pre-determined value, the LVDO bit will be
set high indicating a low power supply voltage condition. The Low Voltage Detector function is
supplied by a reference voltage which will be automatically enabled. When the devices are powered
down the low voltage detector will remain active if the LVDEN bit is high. After enabling the Low
Voltage Detector, a time delay tLVDS should be allowed for the circuitry to stabilise before reading the
LVDO bit. Note also that as the VDD voltage may rise and fall rather slowly, at the voltage nears that
of VLVD, there may be multiple bit LVDO transitions.
The Low Voltage Detector also has its own interrupt which is contained within one of the Multifunction interrupts, providing an alternative means of low voltage detection, in addition to polling
the LVDO bit. The interrupt will only be generated after a delay of tLVD after the LVDO bit has been
set high by a low voltage condition. When the devices are powered down the Low Voltage Detector
will remain active if the LVDEN bit is high. In this case, the LVDF interrupt request flag will be
set, causing an interrupt to be generated if VDD falls below the preset LVD voltage. This will cause
the devices to wake-up from the SLEEP or IDLE Mode, however if the Low Voltage Detector wake
up function is not required then the LVDF flag should be first set high before the devices enters the
SLEEP or IDLE Mode.
LVD Operation
Rev. 1.00
136
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Voice Output
Voice Control
The voice control register controls the DAC circuit. If the DAC circuit is not enabled, any DAH/
DAL outputs will be invalid. Writing a “1” to the DACEN bit will enable the DAC circuit and
channel the DAC output to its corresponding I/O pin, while writing a “0” to the DACEN bit will
disable the DAC circuit.
Audio Output and Volume Control – DAL, DAH, DACTRL
The audio output is 12-bits wide whose highest 8-bits are written into the DAH register and whose
lowest four bits are written into the highest four bits of the DAL register. Bits 0~3 of the DAL
register are always read as zero.
There are 8 levels of volume which are setup using the DACTRL register. The highest 3-bits of
this register are used for volume control and the DACEN bit is used to control the DAC function
enable or not. Once the DACEN bit is set to “1”, this will channel the DAC output to the I/O pin and
disable the original I/O pin shared function.
DAL Register
Bit
7
6
5
4
3
2
1
0
Name
D3
D2
D1
D0
—
—
—
—
R/W
R/W
R/W
R/W
R/W
—
—
—
—
POR
0
0
0
0
—
—
—
—
4
3
2
1
0
Bit 7~4
D3~D0: Audio output low 4 bit
Bit 3~0
unimplemented, read as “0”
DAH Register
Bit
7
6
5
Name
D11
D10
D9
D8
D7
D6
D5
D4
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
POR
0
0
0
0
0
0
0
0
Bit 7~0
D11~D4: Audio output high 8 bit
DACTRL Register
Bit
7
6
5
4
3
2
1
0
Name
VOL2
VOL1
VOL0
—
—
—
—
DACEN
R/W
R/W
R/W
R/W
—
—
—
—
R/W
POR
0
0
0
—
—
—
—
0
Bit 7~5
VOL2~VOL0: DAC volume control bit
000: min. volume
111: max. volume
Bit 4~1
unimplemented, read as “0”
Bit 0
DACEN: DAC enable control bit
0: disable
1: enable
Note: When the DACEN is set to “1”, the DAC signal will be channeled to the I/O pin anddisable
the original I/O pin shared function. Howerer, the D/A convereter output pin AUD is not
connected to the external pin and internally used only.
Rev. 1.00
137
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Power Line Data Transceiver
Power Line Data Transceiver provides a way to transmit and receive data on the common power
lines of an interconnected array of microcontroller based subsystems. By having one of these
devices inside each subsystem, the shared power and data cabling can be reduced to a simple two
line type, offering major installation cost reductions.
VCC
VBG=1.5V
LDO
3.3V
VDD
CEB
5.6V
Zener
LVD
5.25V
CN
VDD
–
CMP
R
RX
+
10MΩ
EN1B
EN1
CMP & OPA Enable
VDD
VDD
EN1B
TRX
EN1
EN1B
RPU
TX
EN1B
1.5V
EN
VSS
+
OPA
–
IS
Current Modulator
Power Line Data Transceiver Block Diagram
Rev. 1.00
138
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Positive Power Supply Line
Master
Controller
Ground Line
Power Line Data
Transceiver
Power Line Data
Transceiver
Power Line Data
Transceiver
MCU
MCU
MCU
Subsystem
#2
Subsystem
#n
Subsystem
#1
Power Line Data Transceiver System Block Diagram
Shared Power Line
All microcontroller based subsystems are connected together via the same two line power
connection. The ground line is hardwired to each subsystem while the positive power line is
connected to the VIN pin on the Power Line Data Transceiver device. An internal Low Dropout
Voltage Regulator within the Power Line Data Transceiver device converts this input power supply
voltage to a fixed voltage level which is supplied to the subsystem microcontroller and other circuit
components. In this way when the power line voltage is changed due to the transmission or reception
of data the subsystem circuits still continue to receive a regulated power supply.
Data Transmission (From master controller to slave device)
Refer to the application circuit when reading the following description. The master controller
transmites the data by modulate the positibe power line (L+) voltage. Using this method should be
pay attention to the noise tolerance of the devices operating voltage and the TRX pin receiving data.
As the devices include a voltage regulator which is used as the power supply to the subsystem units,
then the subsystem power supply voltage will not be affected as long as the regulator minimum
dropout voltage is maintained. Then a voltage modulation signal will be detected in the TRX pin
to make the TRX pin voltage drop lower than the threshold voltage (VT). However a reduction in
the power supply will be detected by the CMP internal comparator.The output of this comparator is
connected to pin RX can be connected to a microcontroller input for use as a data signal.
VTRX
VMARK
VT
VRX
VVDD
Power Line Data Reception
Rev. 1.00
139
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Data Reception (From slave device to master controller)
Refer to the application circuit when reading the following description. The Power Line Data
Transceiver slave device can transmit data to the master controller by modulating the current on the
power supply line. The slave devices pull the TX pin voltage to a low level to enable the internal
current modulator. The modeulator will provide a constant current load by the transistor connected
to the internal modulator OPA output NMOS terminal. The constant current load is supplied by the
power line through the TRX pin, and can be adjusted by the RS resistor connected on the IS pin.
Therefore, the current modulation signals can be generated on the TRX pin by control the TX pin
voltage level. The current modulation signal can return to the master controller throuth the power
supply line.
VTX
VVDD
IIS
IMC
Current Modulator
The device can modulate power line current by adding additional constant current source which
control by TX pin. When TX pin connect to low level will enable this current modulation function.
The modulation current can be calculated by the following formula:
IIS = 1.5V/RS
Application Considerations
It is envisaged that the devices will be used together with microcontroller based subsystems
which will be required to provide two I/O pins for data transmission and reception. The MCU pin
connected to theTX pin must be setup as an output while the MCU pin connected to the RX pin
must be setup as an input.
Power impedance plays an important role in the power data transceiver applications, so it must be
well defined to be used in reliable data transmit and receive operations.
The external components connected to the TRX pin must be carefully selected to ensure that an
enough pulse duration time is occured on the RX pin.
Common decoupling protection must be taken to ensure reliable operation.
Rev. 1.00
140
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Power Line Data Transceiver Application Circuits
1N4148
1N4004
1kΩ
VBG=1.5V
VCC
LDO
3.3V
22u
1N4004
VDD
104
CEB
L+
5.6V
Zener
L-
1N4004
LVD
5.25V
1N4004
CN
VDD
–
104
R
RX
CMP
10MΩ
+
EN1B
EN1
CMP & OPA Enable
VDD
MCU
EN1B
EN1
VDD
100Ω
EN1B
TRX
RPU
TX
2MΩ
1.5V
EN
+
EN1B
VSS
OPA
I IS 
RS
Rev. 1.00
1.5V
Rs
–
IS
Current Modulator
100Ω
141
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Configuration Options
Configuration options refer to certain options within the MCU that are programmed into the OTP
Program Memory devices during the programming process. During the development process,
these options are selected using the HT-IDE software development tools. As these options are
programmed into the device using the hardware programming tools, once they are selected they
can not be changed later by the application software. All options must be defined for proper system
function, the details of which are shown in the table.
No.
Options
Oscillator Options
1
OSC type selection: crystal or HIRC or EC (external clock)
00: HXT (Filter On)
01: HIRC (Filter Off)
10: EC (Filter Off)
2
Low speed system oscillator selection – fL: LXT, LIRC
3
HIRC frequency selection: 910kHz, 2MHz, 4MHz, 8MHz
4
fS clock selection: fSUB or fSYS/4
5
HXT mode selection: 455kHz or 1MHz~8MHz
Watchdog Options
6
WDT enable or disable
7
CLR WDT instructions: 1 or 2 instructions
LVR/LVD Options
8
LVR function: enable or disable
9
LVR voltage: 2.1V or 2.55V or 3.15V or 4.2V
RC Filter
10
RC filter for TMR0/1 & INT0/1, enable or disable
11
SIM enable/disable
12
SPI_WCOL: enable/disable
13
SPI_CSEN: enable/disable, used to enable/disable (1/0) software CSEN function
14
I2C Debounce Time: no debounce, 1 system clock, 2 system clock
SPI
I2C
RES
15
I/O or RES function
Lock Options
Rev. 1.00
16
Lock All
17
Partial Lock
142
November 14, 2017
1
1
Z1
T1
Z2
T2
R9
R6
12
12
1
2
3
4
5
82P
82P
ICP
C7
C8
PA0
PA2
PB6
VDD
1N4004
D5
1N4004
D4
1N4004
D7
1N4004
D6
R3
100
D1
1N4148
C13
102
R10
2M
U3
NTC
VDD
50~1K
R5
10K
C3
22uF
R13
200K
R11
2M
LED1
R8
330
C4
103
R34
100
9
D3
D2
IRTX
IRRX
PA3/A1N
PA2/A1P
HT45FH23A
PC2
PC1/AN5
PC0/AN4
PA1
.
IS
.
CN
.
TRX
.
VIN
U1
VDD
4
5
6
1
11
C43
104
10
12
.
18
+
-
OPA1
C1
C10
R12
-
+
EN1
.
17
R15
3.3
T1
8050
10P
5.1M
OPA
C14
PA4/A1E
EN
-
+
PB0
VBG = 1.5V
PA6/A2N
PA5/A2P
1.5V
OR GATE
LEVEL
SHIFT
NOT
GATE
5.25V
LVD
CEB
LDO
3.3V
.
16
102
D9
4148
D8
4148
200K
R19
.
15
PB5
PB6
VSS
VSS
EN1B
VDD
OPA2
C11
-
+
R17
10K
R18
30K
.
1M
33P
PA7/A2E
PC3/AN0/SCS
PA0/CNP
EN1B
VDD
R14
.
14
143
.
Rev. 1.00
R16
560
R20
10K
13
R1
3
2
7
8
19
20
C1
104
VDD
SW2
TS2
Smoke
C2
47uF
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Application Circuits
Note:The components used in this application circuit shluld be changed for different applications.
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Instruction Set
Introduction
Central to the successful operation of any microcontroller is its instruction set, which is a set of
program instruction codes that directs the microcontroller to perform certain operations. In the case
of Holtek microcontroller, a comprehensive and flexible set of over 60 instructions is provided to
enable programmers to implement their application with the minimum of programming overheads.
For easier understanding of the various instruction codes, they have been subdivided into several
functional groupings.
Instruction Timing
Most instructions are implemented within one instruction cycle. The exceptions to this are branch,
call, or table read instructions where two instruction cycles are required. One instruction cycle is
equal to 4 system clock cycles, therefore in the case of an 8MHz system oscillator, most instructions
would be implemented within 0.5μs and branch or call instructions would be implemented within
1μs. Although instructions which require one more cycle to implement are generally limited to
the JMP, CALL, RET, RETI and table read instructions, it is important to realize that any other
instructions which involve manipulation of the Program Counter Low register or PCL will also take
one more cycle to implement. As instructions which change the contents of the PCL will imply a
direct jump to that new address, one more cycle will be required. Examples of such instructions
would be “CLR PCL” or “MOV PCL, A”. For the case of skip instructions, it must be noted that if
the result of the comparison involves a skip operation then this will also take one more cycle, if no
skip is involved then only one cycle is required.
Moving and Transferring Data
The transfer of data within the microcontroller program is one of the most frequently used
operations. Making use of three kinds of MOV instructions, data can be transferred from registers to
the Accumulator and vice-versa as well as being able to move specific immediate data directly into
the Accumulator. One of the most important data transfer applications is to receive data from the
input ports and transfer data to the output ports.
Arithmetic Operations
The ability to perform certain arithmetic operations and data manipulation is a necessary feature of
most microcontroller applications. Within the Holtek microcontroller instruction set are a range of
add and subtract instruction mnemonics to enable the necessary arithmetic to be carried out. Care
must be taken to ensure correct handling of carry and borrow data when results exceed 255 for
addition and less than 0 for subtraction. The increment and decrement instructions INC, INCA, DEC
and DECA provide a simple means of increasing or decreasing by a value of one of the values in the
destination specified.
Rev. 1.00
144
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Logical and Rotate Operation
The standard logical operations such as AND, OR, XOR and CPL all have their own instruction
within the Holtek microcontroller instruction set. As with the case of most instructions involving
data manipulation, data must pass through the Accumulator which may involve additional
programming steps. In all logical data operations, the zero flag may be set if the result of the
operation is zero. Another form of logical data manipulation comes from the rotate instructions such
as RR, RL, RRC and RLC which provide a simple means of rotating one bit right or left. Different
rotate instructions exist depending on program requirements. Rotate instructions are useful for serial
port programming applications where data can be rotated from an internal register into the Carry
bit from where it can be examined and the necessary serial bit set high or low. Another application
which rotate data operations are used is to implement multiplication and division calculations.
Branches and Control Transfer
Program branching takes the form of either jumps to specified locations using the JMP instruction
or to a subroutine using the CALL instruction. They differ in the sense that in the case of a
subroutine call, the program must return to the instruction immediately when the subroutine has
been carried out. This is done by placing a return instruction “RET” in the subroutine which will
cause the program to jump back to the address right after the CALL instruction. In the case of a JMP
instruction, the program simply jumps to the desired location. There is no requirement to jump back
to the original jumping off point as in the case of the CALL instruction. One special and extremely
useful set of branch instructions are the conditional branches. Here a decision is first made regarding
the condition of a certain data memory or individual bits. Depending upon the conditions, the
program will continue with the next instruction or skip over it and jump to the following instruction.
These instructions are the key to decision making and branching within the program perhaps
determined by the condition of certain input switches or by the condition of internal data bits.
Bit Operations
The ability to provide single bit operations on Data Memory is an extremely flexible feature of all
Holtek microcontrollers. This feature is especially useful for output port bit programming where
individual bits or port pins can be directly set high or low using either the “SET [m].i” or “CLR [m].i”
instructions respectively. The feature removes the need for programmers to first read the 8-bit output
port, manipulate the input data to ensure that other bits are not changed and then output the port with
the correct new data. This read-modify-write process is taken care of automatically when these bit
operation instructions are used.
Table Read Operations
Data storage is normally implemented by using registers. However, when working with large
amounts of fixed data, the volume involved often makes it inconvenient to store the fixed data in
the Data Memory. To overcome this problem, Holtek microcontrollers allow an area of Program
Memory to be set as a table where data can be directly stored. A set of easy to use instructions
provides the means by which this fixed data can be referenced and retrieved from the Program
Memory.
Other Operations
In addition to the above functional instructions, a range of other instructions also exist such as
the “HALT” instruction for Power-down operations and instructions to control the operation of
the Watchdog Timer for reliable program operations under extreme electric or electromagnetic
environments. For their relevant operations, refer to the functional related sections.
Rev. 1.00
145
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Instruction Set Summary
The following table depicts a summary of the instruction set categorised according to function and
can be consulted as a basic instruction reference using the following listed conventions.
Table Conventions
x: Bits immediate data
m: Data Memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Mnemonic
Description
Cycles
Flag Affected
Add Data Memory to ACC
Add ACC to Data Memory
Add immediate data to ACC
Add Data Memory to ACC with Carry
Add ACC to Data memory with Carry
Subtract immediate data from the ACC
Subtract Data Memory from ACC
Subtract Data Memory from ACC with result in Data Memory
Subtract Data Memory from ACC with Carry
Subtract Data Memory from ACC with Carry, result in Data Memory
Decimal adjust ACC for Addition with result in Data Memory
1
1Note
1
1
1Note
1
1
1Note
1
1Note
1Note
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
Z, C, AC, OV
C
1
1
1
1Note
1Note
1Note
1
1
1
1Note
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Increment Data Memory with result in ACC
Increment Data Memory
Decrement Data Memory with result in ACC
Decrement Data Memory
1
1Note
1
1Note
Z
Z
Z
Z
Rotate Data Memory right with result in ACC
Rotate Data Memory right
Rotate Data Memory right through Carry with result in ACC
Rotate Data Memory right through Carry
Rotate Data Memory left with result in ACC
Rotate Data Memory left
Rotate Data Memory left through Carry with result in ACC
Rotate Data Memory left through Carry
1
1Note
1
1Note
1
1Note
1
1Note
None
None
C
C
None
None
C
C
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
Logical AND Data Memory to ACC
Logical OR Data Memory to ACC
Logical XOR Data Memory to ACC
Logical AND ACC to Data Memory
Logical OR ACC to Data Memory
Logical XOR ACC to Data Memory
Logical AND immediate Data to ACC
Logical OR immediate Data to ACC
Logical XOR immediate Data to ACC
Complement Data Memory
Complement Data Memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Rev. 1.00
146
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Mnemonic
Description
Cycles
Flag Affected
Move Data Memory to ACC
Move ACC to Data Memory
Move immediate data to ACC
1
1Note
1
None
None
None
Clear bit of Data Memory
Set bit of Data Memory
1Note
1Note
None
None
Jump unconditionally
Skip if Data Memory is zero
Skip if Data Memory is zero with data movement to ACC
Skip if bit i of Data Memory is zero
Skip if bit i of Data Memory is not zero
Skip if increment Data Memory is zero
Skip if decrement Data Memory is zero
Skip if increment Data Memory is zero with result in ACC
Skip if decrement Data Memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1Note
1Note
1Note
1Note
1Note
1Note
1Note
1Note
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read table (specific page) to TBLH and Data Memory
Read table (current page) to TBLH and Data Memory
Read table (last page) to TBLH and Data Memory
2Note
2Note
2Note
None
None
None
No operation
Clear Data Memory
Set Data Memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of Data Memory
Swap nibbles of Data Memory with result in ACC
Enter power down mode
1
1Note
1Note
1
1
1
1Note
1
1
None
None
None
TO, PDF
TO, PDF
TO, PDF
None
None
TO, PDF
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Branch Operation
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read Operation
TABRD [m]
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note: 1. For skip instructions, if the result of the comparison involves a skip then two cycles are required, if no
skip takes place only one cycle is required.
2. Any instruction which changes the contents of the PCL will also require 2 cycles for execution.
3. For the “CLR WDT1” and “CLR WDT2” instructions the TO and PDF flags may be affected by the
execution status. The TO and PDF flags are cleared after both “CLR WDT1” and “CLR WDT2”
instructions are consecutively executed. Otherwise the TO and PDF flags remain unchanged.
Rev. 1.00
147
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Instruction Definition
ADC A,[m]
Description
Operation
Affected flag(s)
ADCM A,[m]
Description
Operation
Affected flag(s)
ADD A,[m]
Description
Add Data Memory to ACC with Carry
The contents of the specified Data Memory, Accumulator and the carry flag are added.
The result is stored in the Accumulator.
ACC ← ACC + [m] + C
OV, Z, AC, C
Add ACC to Data Memory with Carry
The contents of the specified Data Memory, Accumulator and the carry flag are added.
The result is stored in the specified Data Memory.
[m] ← ACC + [m] + C
OV, Z, AC, C
Add Data Memory to ACC
The contents of the specified Data Memory and the Accumulator are added.
The result is stored in the Accumulator.
Operation
Affected flag(s)
ACC ← ACC + [m]
OV, Z, AC, C
ADD A,x
Description
Add immediate data to ACC
The contents of the Accumulator and the specified immediate data are added.
The result is stored in the Accumulator.
ACC ← ACC + x
OV, Z, AC, C
Operation
Affected flag(s)
ADDM A,[m]
Description
Operation
Affected flag(s)
AND A,[m]
Description
Operation
Affected flag(s)
AND A,x
Description
Operation
Affected flag(s)
ANDM A,[m]
Description
Operation
Affected flag(s)
Rev. 1.00
Add ACC to Data Memory
The contents of the specified Data Memory and the Accumulator are added.
The result is stored in the specified Data Memory.
[m] ← ACC + [m]
OV, Z, AC, C
Logical AND Data Memory to ACC
Data in the Accumulator and the specified Data Memory perform a bitwise logical AND
operation. The result is stored in the Accumulator.
ACC ← ACC ″AND″ [m]
Z
Logical AND immediate data to ACC
Data in the Accumulator and the specified immediate data perform a bit wise logical AND
operation. The result is stored in the Accumulator.
ACC ← ACC ″AND″ x
Z
Logical AND ACC to Data Memory
Data in the specified Data Memory and the Accumulator perform a bitwise logical AND
operation. The result is stored in the Data Memory.
[m] ← ACC ″AND″ [m]
Z
148
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Affected flag(s)
Subroutine call
Unconditionally calls a subroutine at the specified address. The Program Counter then
increments by 1 to obtain the address of the next instruction which is then pushed onto the
stack. The specified address is then loaded and the program continues execution from this
new address. As this instruction requires an additional operation, it is a two cycle instruction.
Stack ← Program Counter + 1
Program Counter ← addr
None
CLR [m]
Description
Operation
Affected flag(s)
Clear Data Memory
Each bit of the specified Data Memory is cleared to 0.
[m] ← 00H
None
CLR [m].i
Description
Operation
Affected flag(s)
Clear bit of Data Memory
Bit i of the specified Data Memory is cleared to 0.
[m].i ← 0
None
CLR WDT
Description
Operation
Clear Watchdog Timer
The TO, PDF flags and the WDT are all cleared.
WDT cleared
TO ← 0
PDF ← 0
TO, PDF
CALL addr
Description
Operation
Affected flag(s)
CLR WDT1
Description
Operation
Affected flag(s)
CLR WDT2
Description
Operation
Affected flag(s)
CPL [m]
Description
Operation
Affected flag(s)
Rev. 1.00
Pre-clear Watchdog Timer
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in
conjunction with CLR WDT2 and must be executed alternately with CLR WDT2 to have
effect. Repetitively executing this instruction without alternately executing CLR WDT2 will
have no effect.
WDT cleared
TO ← 0
PDF ← 0
TO, PDF
Pre-clear Watchdog Timer
The TO, PDF flags and the WDT are all cleared. Note that this instruction works in conjunction
with CLR WDT1 and must be executed alternately with CLR WDT1 to have effect.
Repetitively executing this instruction without alternately executing CLR WDT1 will have no
effect.
WDT cleared
TO ← 0
PDF ← 0
TO, PDF
Complement Data Memory
Each bit of the specified Data Memory is logically complemented (1′s complement). Bits which
previously contained a 1 are changed to 0 and vice versa.
[m] ← [m]
Z
149
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
CPLA [m]
Description
Operation
Affected flag(s)
Complement Data Memory with result in ACC
Each bit of the specified Data Memory is logically complemented (1′s complement). Bits which
previously contained a 1 are changed to 0 and vice versa. The complemented result is stored in
the Accumulator and the contents of the Data Memory remain unchanged.
ACC ← [m]
Z
Affected flag(s)
Decimal-Adjust ACC for addition with result in Data Memory
Convert the contents of the Accumulator value to a BCD (Binary Coded Decimal) value
resulting from the previous addition of two BCD variables. If the low nibble is greater than 9
or if AC flag is set, then a value of 6 will be added to the low nibble. Otherwise the low nibble
remains unchanged. If the high nibble is greater than 9 or if the C flag is set, then a value of 6
will be added to the high nibble. Essentially, the decimal conversion is performed by adding
00H, 06H, 60H or 66H depending on the Accumulator and flag conditions. Only the C flag
may be affected by this instruction which indicates that if the original BCD sum is greater than
100, it allows multiple precision decimal addition.
[m] ← ACC + 00H or
[m] ← ACC + 06H or
[m] ← ACC + 60H or
[m] ← ACC + 66H
C
DEC [m]
Description
Operation
Affected flag(s)
Decrement Data Memory
Data in the specified Data Memory is decremented by 1.
[m] ← [m] − 1
Z
DECA [m]
Description
Decrement Data Memory with result in ACC
Data in the specified Data Memory is decremented by 1. The result is stored in the
Accumulator. The contents of the Data Memory remain unchanged.
ACC ← [m] − 1
Z
DAA [m]
Description
Operation
Operation
Affected flag(s)
Affected flag(s)
Enter power down mode
This instruction stops the program execution and turns off the system clock. The contents of
the Data Memory and registers are retained. The WDT and prescaler are cleared. The power
down flag PDF is set and the WDT time-out flag TO is cleared.
TO ← 0
PDF ← 1
TO, PDF
INC [m]
Description
Operation
Affected flag(s)
Increment Data Memory
Data in the specified Data Memory is incremented by 1.
[m] ← [m] + 1
Z
INCA [m]
Description
Increment Data Memory with result in ACC
Data in the specified Data Memory is incremented by 1. The result is stored in the Accumulator.
The contents of the Data Memory remain unchanged.
ACC ← [m] + 1
Z
HALT
Description
Operation
Operation
Affected flag(s)
Rev. 1.00
150
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Operation
Affected flag(s)
Jump unconditionally
The contents of the Program Counter are replaced with the specified address. Program
execution then continues from this new address. As this requires the insertion of a dummy
instruction while the new address is loaded, it is a two cycle instruction.
Program Counter ← addr
None
MOV A,[m]
Description
Operation
Affected flag(s)
Move Data Memory to ACC
The contents of the specified Data Memory are copied to the Accumulator.
ACC ← [m]
None
MOV A,x
Description
Operation
Affected flag(s)
Move immediate data to ACC
The immediate data specified is loaded into the Accumulator.
ACC ← x
None
MOV [m],A
Description
Operation
Affected flag(s)
Move ACC to Data Memory
The contents of the Accumulator are copied to the specified Data Memory.
[m] ← ACC
None
NOP
Description
Operation
Affected flag(s)
No operation
No operation is performed. Execution continues with the next instruction.
No operation
None
OR A,[m]
Description
Logical OR Data Memory to ACC
Data in the Accumulator and the specified Data Memory perform a bitwise
logical OR operation. The result is stored in the Accumulator.
ACC ← ACC ″OR″ [m]
Z
JMP addr
Description
Operation
Affected flag(s)
OR A,x
Description
Operation
Affected flag(s)
ORM A,[m]
Description
Operation
Affected flag(s)
RET
Description
Operation
Affected flag(s)
Rev. 1.00
Logical OR immediate data to ACC
Data in the Accumulator and the specified immediate data perform a bitwise logical OR
operation. The result is stored in the Accumulator.
ACC ← ACC ″OR″ x
Z
Logical OR ACC to Data Memory
Data in the specified Data Memory and the Accumulator perform a bitwise logical OR
operation. The result is stored in the Data Memory.
[m] ← ACC ″OR″ [m]
Z
Return from subroutine
The Program Counter is restored from the stack. Program execution continues at the restored
address.
Program Counter ← Stack
None
151
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
RET A,x
Description
Operation
Affected flag(s)
RETI
Description
Operation
Affected flag(s)
RL [m]
Description
Operation
Affected flag(s)
RLA [m]
Description
Operation
Affected flag(s)
RLC [m]
Description
Operation
Affected flag(s)
RLCA [m]
Description
Operation
Affected flag(s)
RR [m]
Description
Operation
Affected flag(s)
Rev. 1.00
Return from subroutine and load immediate data to ACC
The Program Counter is restored from the stack and the Accumulator loaded with the specified
immediate data. Program execution continues at the restored address.
Program Counter ← Stack
ACC ← x
None
Return from interrupt
The Program Counter is restored from the stack and the interrupts are re-enabled by setting the
EMI bit. EMI is the master interrupt global enable bit. If an interrupt was pending when the
RETI instruction is executed, the pending Interrupt routine will be processed before returning
to the main program.
Program Counter ← Stack
EMI ← 1
None
Rotate Data Memory left
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit 0.
[m].(i+1) ← [m].i; (i=0~6)
[m].0 ← [m].7
None
Rotate Data Memory left with result in ACC
The contents of the specified Data Memory are rotated left by 1 bit with bit 7 rotated into bit 0.
The rotated result is stored in the Accumulator and the contents of the Data Memory remain
unchanged.
ACC.(i+1) ← [m].i; (i=0~6)
ACC.0 ← [m].7
None
Rotate Data Memory left through Carry
The contents of the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7
replaces the Carry bit and the original carry flag is rotated into bit 0.
[m].(i+1) ← [m].i; (i=0~6)
[m].0 ← C
C ← [m].7
C
Rotate Data Memory left through Carry with result in ACC
Data in the specified Data Memory and the carry flag are rotated left by 1 bit. Bit 7 replaces the
Carry bit and the original carry flag is rotated into the bit 0. The rotated result is stored in the
Accumulator and the contents of the Data Memory remain unchanged.
ACC.(i+1) ← [m].i; (i=0~6)
ACC.0 ← C
C ← [m].7
C
Rotate Data Memory right
The contents of the specified Data Memory are rotated right by 1 bit with bit 0 rotated into bit 7.
[m].i ← [m].(i+1); (i=0~6)
[m].7 ← [m].0
None
152
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
RRA [m]
Description
Operation
Affected flag(s)
RRC [m]
Description
Operation
Affected flag(s)
RRCA [m]
Description
Operation
Affected flag(s)
SBC A,[m]
Description
Operation
Affected flag(s)
SBCM A,[m]
Description
Operation
Affected flag(s)
SDZ [m]
Description
Operation
Affected flag(s)
Rev. 1.00
Rotate Data Memory right with result in ACC
Data in the specified Data Memory and the carry flag are rotated right by 1 bit with bit 0
rotated into bit 7. The rotated result is stored in the Accumulator and the contents of the
Data Memory remain unchanged.
ACC.i ← [m].(i+1); (i=0~6)
ACC.7 ← [m].0
None
Rotate Data Memory right through Carry
The contents of the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0
replaces the Carry bit and the original carry flag is rotated into bit 7.
[m].i ← [m].(i+1); (i=0~6)
[m].7 ← C
C ← [m].0
C
Rotate Data Memory right through Carry with result in ACC
Data in the specified Data Memory and the carry flag are rotated right by 1 bit. Bit 0 replaces
the Carry bit and the original carry flag is rotated into bit 7. The rotated result is stored in the
Accumulator and the contents of the Data Memory remain unchanged.
ACC.i ← [m].(i+1); (i=0~6)
ACC.7 ← C
C ← [m].0
C
Subtract Data Memory from ACC with Carry
The contents of the specified Data Memory and the complement of the carry flag are
subtracted from the Accumulator. The result is stored in the Accumulator. Note that if the
result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is
positive or zero, the C flag will be set to 1.
ACC ← ACC − [m] − C
OV, Z, AC, C
Subtract Data Memory from ACC with Carry and result in Data Memory
The contents of the specified Data Memory and the complement of the carry flag are
subtracted from the Accumulator. The result is stored in the Data Memory. Note that if the
result of subtraction is negative, the C flag will be cleared to 0, otherwise if the result is
positive or zero, the C flag will be set to 1.
[m] ← ACC − [m] − C
OV, Z, AC, C
Skip if decrement Data Memory is 0
The contents of the specified Data Memory are first decremented by 1. If the result is 0 the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
[m] ← [m] − 1
Skip if [m]=0
None
153
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Affected flag(s)
Skip if decrement Data Memory is zero with result in ACC
The contents of the specified Data Memory are first decremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy
instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not 0,
the program proceeds with the following instruction.
ACC ← [m] − 1
Skip if ACC=0
None
SET [m]
Description
Operation
Affected flag(s)
Set Data Memory
Each bit of the specified Data Memory is set to 1.
[m] ← FFH
None
SET [m].i
Description
Operation
Affected flag(s)
Set bit of Data Memory
Bit i of the specified Data Memory is set to 1.
[m].i ← 1
None
SIZ [m]
Description
Skip if increment Data Memory is 0
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. As this requires the insertion of a dummy instruction while
the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the program
proceeds with the following instruction.
[m] ← [m] + 1
Skip if [m]=0
None
SDZA [m]
Description
Operation
Operation
Affected flag(s)
SIZA [m]
Description
Operation
Affected flag(s)
SNZ [m].i
Description
Operation
Affected flag(s)
SUB A,[m]
Description
Operation
Affected flag(s)
Rev. 1.00
Skip if increment Data Memory is zero with result in ACC
The contents of the specified Data Memory are first incremented by 1. If the result is 0, the
following instruction is skipped. The result is stored in the Accumulator but the specified
Data Memory contents remain unchanged. As this requires the insertion of a dummy
instruction while the next instruction is fetched, it is a two cycle instruction. If the result is not
0 the program proceeds with the following instruction.
ACC ← [m] + 1
Skip if ACC=0
None
Skip if bit i of Data Memory is not 0
If bit i of the specified Data Memory is not 0, the following instruction is skipped. As this
requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is 0 the program proceeds with the following instruction.
Skip if [m].i ≠ 0
None
Subtract Data Memory from ACC
The specified Data Memory is subtracted from the contents of the Accumulator. The result is
stored in the Accumulator. Note that if the result of subtraction is negative, the C flag will be
cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
ACC ← ACC − [m]
OV, Z, AC, C
154
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
SUBM A,[m]
Description
Operation
Affected flag(s)
Subtract Data Memory from ACC with result in Data Memory
The specified Data Memory is subtracted from the contents of the Accumulator. The result is
stored in the Data Memory. Note that if the result of subtraction is negative, the C flag will be
cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
[m] ← ACC − [m]
OV, Z, AC, C
Operation
Affected flag(s)
Subtract immediate data from ACC
The immediate data specified by the code is subtracted from the contents of the Accumulator.
The result is stored in the Accumulator. Note that if the result of subtraction is negative, the C
flag will be cleared to 0, otherwise if the result is positive or zero, the C flag will be set to 1.
ACC ← ACC − x
OV, Z, AC, C
SWAP [m]
Description
Operation
Affected flag(s)
Swap nibbles of Data Memory
The low-order and high-order nibbles of the specified Data Memory are interchanged.
[m].3~[m].0 ↔ [m].7~[m].4
None
SWAPA [m]
Description
Swap nibbles of Data Memory with result in ACC
The low-order and high-order nibbles of the specified Data Memory are interchanged. The
result is stored in the Accumulator. The contents of the Data Memory remain unchanged.
ACC.3~ACC.0 ← [m].7~[m].4
ACC.7~ACC.4 ← [m].3~[m].0
None
SUB A,x
Description
Operation
Affected flag(s)
SZ [m]
Description
Operation
Affected flag(s)
SZA [m]
Description
Operation
Affected flag(s)
SZ [m].i
Description
Operation
Affected flag(s)
Rev. 1.00
Skip if Data Memory is 0
If the contents of the specified Data Memory is 0, the following instruction is skipped. As this
requires the insertion of a dummy instruction while the next instruction is fetched, it is a two
cycle instruction. If the result is not 0 the program proceeds with the following instruction.
Skip if [m]=0
None
Skip if Data Memory is 0 with data movement to ACC
The contents of the specified Data Memory are copied to the Accumulator. If the value is zero,
the following instruction is skipped. As this requires the insertion of a dummy instruction
while the next instruction is fetched, it is a two cycle instruction. If the result is not 0 the
program proceeds with the following instruction.
ACC ← [m]
Skip if [m]=0
None
Skip if bit i of Data Memory is 0
If bit i of the specified Data Memory is 0, the following instruction is skipped. As this requires
the insertion of a dummy instruction while the next instruction is fetched, it is a two cycle
instruction. If the result is not 0, the program proceeds with the following instruction.
Skip if [m].i=0
None
155
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
TABRD [m]
Description
Operation
Affected flag(s)
TABRDC [m]
Description
Operation
Affected flag(s)
TABRDL [m]
Description
Operation
Affected flag(s)
XOR A,[m]
Description
Operation
Affected flag(s)
XORM A,[m]
Description
Operation
Affected flag(s)
XOR A,x
Description
Operation
Affected flag(s)
Rev. 1.00
Read table (specific page) to TBLH and Data Memory
The low byte of the program code (specific page) addressed by the table pointer pair
(TBHP and TBLP) is moved to the specified Data Memory and the high byte moved to TBLH.
[m] ← program code (low byte)
TBLH ← program code (high byte)
None
Read table (current page) to TBLH and Data Memory
The low byte of the program code (current page) addressed by the table pointer (TBLP) is
moved to the specified Data Memory and the high byte moved to TBLH.
[m] ← program code (low byte)
TBLH ← program code (high byte)
None
Read table (last page) to TBLH and Data Memory
The low byte of the program code (last page) addressed by the table pointer (TBLP) is moved
to the specified Data Memory and the high byte moved to TBLH.
[m] ← program code (low byte)
TBLH ← program code (high byte)
None
Logical XOR Data Memory to ACC
Data in the Accumulator and the specified Data Memory perform a bitwise logical XOR
operation. The result is stored in the Accumulator.
ACC ← ACC ″XOR″ [m]
Z
Logical XOR ACC to Data Memory
Data in the specified Data Memory and the Accumulator perform a bitwise logical XOR
operation. The result is stored in the Data Memory.
[m] ← ACC ″XOR″ [m]
Z
Logical XOR immediate data to ACC
Data in the Accumulator and the specified immediate data perform a bitwise logical XOR
operation. The result is stored in the Accumulator.
ACC ← ACC ″XOR″ x
Z
156
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Package Information
Note that the package information provided here is for consultation purposes only. As this
information may be updated at regular intervals users are reminded to consult the Holtek website for
the latest version of the Package/Carton Information.
Additional supplementary information with regard to packaging is listed below. Click on the relevant
section to be transferred to the relevant website page.
• Further Package Information (include Outline Dimensions, Product Tape and Reel Specifications)
• Packing Meterials Information
• Carton information
Rev. 1.00
157
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
20-pin SOP (300mil) Outline Dimensions
Symbol
Dimensions in inch
Min.
Nom.
Max.
A
—
0.406 BSC
—
B
—
0.295 BSC
—
0.020
C
0.012
—
C’
—
0.504 BSC
—
D
—
—
0.104
E
—
0.050 BSC
—
F
0.004
—
0.012
G
0.016
—
0.050
H
0.008
—
0.013
α
0°
—
8°
Symbol
Rev. 1.00
Dimensions in mm
Min.
Nom.
Max.
A
—
10.30 BSC
—
B
—
7.50 BSC
—
C
0.31
—
0.51
C’
—
12.80 BSC
—
D
—
—
2.65
E
—
1.27 BSC
—
F
0.10
—
0.30
G
0.40
—
1.27
H
0.20
—
0.33
α
0°
—
8°
158
November 14, 2017
HT45FH23A/HT45FH24A
Smoke Detector Flash MCU with Power Line Transceiver
Copyright© 2017 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time
of publication. However, Holtek assumes no responsibility arising from the use of
the specifications described. The applications mentioned herein are used solely
for the purpose of illustration and Holtek makes no warranty or representation that
such applications will be suitable without further modification, nor recommends
the use of its products for application that may present a risk to human life due to
malfunction or otherwise. Holtek's products are not authorized for use as critical
components in life support devices or systems. Holtek reserves the right to alter
its products without prior notification. For the most up-to-date information, please
visit our web site at http://www.holtek.com.tw.
Rev. 1.00
159
November 14, 2017