Burr-Brown ADS1254E 24-bit, 20khz, low power analog-to-digital converter Datasheet

ADS1254
ADS
125
4
SBAS213 – JUNE 2001
24-Bit, 20kHz, Low Power
ANALOG-TO-DIGITAL CONVERTER
FEATURES
DESCRIPTION
● 24 BITS—NO MISSING CODES
● 19 BITS EFFECTIVE RESOLUTION UP TO
20kHz DATA RATE
● LOW NOISE: 1.8ppm
● FOUR DIFFERENTIAL INPUTS
● INL: 15ppm (max)
● EXTERNAL REFERENCE (0.5V to 5V)
● POWER-DOWN MODE
● SYNC MODE
● LOW POWER: 4mW at 20kHz
● SEPARATE DIGITAL INTERFACE SUPPLY 1.8V
to 3.6V
The ADS1254 is a precision, wide dynamic range, deltasigma, Analog-to-Digital (A/D) converter with 24-bit resolution. The delta-sigma architecture is used for wide dynamic range and to ensure 24 bits of no missing codes
performance. An effective resolution of 19 bits (1.8ppm of
rms noise) is achieved for conversion rates up to 20kHz.
The ADS1254 is designed for high-resolution measurement
applications in cardiac diagnostics, smart transmitters, industrial process control, weight scales, chromatography, and
portable instrumentation. The converter includes a flexible,
two-wire synchronous serial interface for low-cost isolation.
The ADS1254 is a multi-channel converter and is offered in
an SSOP-20 package.
APPLICATIONS
●
●
●
●
●
●
CARDIAC DIAGNOSTICS
DIRECT THERMOCOUPLE INTERFACES
BLOOD ANALYSIS
INFRARED PYROMETERS
LIQUID/GAS CHROMATOGRAPHY
PRECISION PROCESS CONTROL
ADS1254
VREF
CH1+
CH1–
CLK
CH2+
CH2–
Mux
CH3+
4th-Order
∆Σ
Modulator
Digital
Filter
Serial
Interface
CH3–
SCLK
DOUT/DRDY
AVDD
CH4+
AGND
CH4–
Control
DVDD
DGND
CHSEL0 CHSEL1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright © 2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
www.ti.com
ELECTROSTATIC
DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS
Analog Input: Current (Momentary) .............................................. ±100mA
(Continuous) ............................................... ±10mA
Voltage ................................... GND – 0.3V to VDD + 0.3V
AVDD to AGND ....................................................................... –0.3V to 6V
DVDD to AVDD .......................................................................... –6V to +6V
DVDD to DGND ....................................................................... –0.3V to 6V
VREF Voltage to AGND ............................................. –0.3V to VDD + 0.3V
Digital Input Voltage to DGND ................................. –0.3V to VDD + 0.3V
Digital Output Voltage to DGND .............................. –0.3V to VDD + 0.3V
Lead Temperature (soldering, 10s) .............................................. +300°C
Power Dissipation (any package) ................................................. 500mW
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
PACKAGE
PACKAGE
DRAWING
NUMBER
ADS1254E
SSOP-20
349
–40°C to +85°C
ADS1254E
"
"
"
"
"
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
MARKING
ORDERING
NUMBER(1)
TRANSPORT
MEDIA
ADS1254E
ADS1254E/2K5
Rails
Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces
of “ADS1254E/2K5” will get a single 2500-piece Tape and Reel.
ELECTRICAL CHARACTERISTICS
All specifications at TMIN to TMAX, AVDD = +5V, DVDD = +1.8V. CLK = 8MHz, and VREF = 4.096, unless otherwise specified.
ADS1254E
PARAMETER
ANALOG INPUT
Input Voltage Range
Input Impedance
Input Capacitance
Input Leakage
DYNAMIC CHARACTERISTICS
Data Rate
Bandwidth
Serial Clock (SCLK)
System Clock Input (CLK)
ACCURACY
Integral Non-Linearity(1)
THD
Noise
Resolution
No Missing Codes
Common-Mode Rejection
Gain Error
Offset Error
Gain Sensitivity to VREF
Power-Supply Rejection Ratio
CONDITIONS
MIN
AGND
CLK = 3,840Hz
CLK = 1MHz
CLK = 8MHz
260
1
125
6
5
At +25°C
At TMIN to TMAX
MAX
UNITS
±VREF
V
MΩ
MΩ
kΩ
pF
pA
nA
50
1
20.8
–3dB
4.24
8
8
1kHz Input; 0.1dB below FS
60Hz, AC
90
70
PERFORMANCE OVER TEMPERATURE
Offset Drift
Gain Drift
VOLTAGE REFERENCE
VREF
Load Current
TYP
±0.0002
105
1.8
24
24
102
0.1
±30
1:1
88
±0.0015
2.7
1
±100
4.096
32
% of FSR
dB
ppm of FSR, rms
Bits
Bits
dB
% of FSR
ppm of FSR
dB
0.07
0.4
0.5
kHz
kHz
MHz
MHz
ppm/°C
ppm/°C
VDD
V
µA
NOTE: (1) Applies to full-differential signals.
2
ADS1254
SBAS213
ELECTRICAL CHARACTERISTICS (Cont.)
All specifications at TMIN to TMAX, AVDD = +5V, DVDD = +1.8V. CLK = 8MHz, and VREF = 4.096, unless otherwise specified.
ADS1254E
PARAMETER
CONDITIONS
DIGITAL INPUT/OUTPUT
Logic Family
Logic Level: VIH
VIL
VOH
VOL
Input (SCLK, CLK, CHSEL0, CHSEL1) Hysteresis
Data Format
MIN
TYP
IOH = –500µA
IOL = 500µA
0.65 • DVDD
–0.3
DVDD –0.4
DVDD
AVDD
AVDD = +5V
DVDD = +1.8V
1.8
4.75
TEMPERATURE RANGE
Operating
Storage
5
0.8
0.2
4.3
0.4
–40
–60
PIN CONFIGURATION
SSOP-20
+85
+100
°C
°C
NAME
PIN DESCRIPTION
1
CH1+
2
CH1–
3
CH2+
4
CH2–
5
CH3+
Analog Input: Positive Input of the Differential Analog Input
Analog Input: Negative Input of the Differential Analog Input
Analog Input: Positive Input of the Differential Analog Input
Analog Input: Negative Input of the Differential Analog Input
Analog Input: Positive Input of the Differential Analog Input
Analog Input: Negative Input of the Differential Analog Input
Input: Analog Power Supply Voltage, +5V
Digital Input: Device System Clock. The
system clock is in the form of a CMOScompatible clock. This is a Schmitt-Trigger
input
Input: Digital Power Supply Voltage
No Connection
No Connection
Input: Digital Ground
Digital Output: Serial Data Output/Data
Ready. This output indicates that a new
output word is available from the ADS1254
data output register. The serial data is
clocked out of the serial data output shift
register using SCLK.
Digital Input: Serial Clock. The serial clock
is in the form of a CMOS-compatible clock.
The serial clock operates independently
from the system clock, therefore, it is possible to run SCLK at a higher frequency
than CLK. The normal state of SCLK is
LOW. Holding SCLK HIGH will either initiate a modulator reset for synchronizing
multiple converters or enter power-down
mode. This is a Schmitt-Trigger input.
Digital Input: Used to select analog input
channel. This is a Schmitt-Trigger Input
Digital Input: Used to select analog input
channel. This is a Schmitt-Trigger Input
Input: Analog Ground
Analog Input: Reference Voltage Input
Analog Input: Negative Input of the Differential Analog Input
Analog Input: Positive Input of the Differential Analog Input
1
20
CH4+
6
CH3–
CH1–
2
19
CH4–
7
8
AVDD
CLK
CH2+
3
18 VREF
CH2–
4
17 AGND
CH3+
5
9
10
11
12
13
DVDD
NC
NC
DGND
DOUT/DRDY
CH3–
14
SCLK
15
CHSEL1
16
CHSEL0
17
18
19
AGND
VREF
CH4–
20
CH4+
16
CHSEL0
6
15
CHSEL1
AVDD
7
14 SCLK
CLK
8
13 DOUT/DRDY
SBAS213
VDC
VDC
mA
mA
mW
µA
PIN
CH1+
ADS1254
3.6
5.25
1.15
0.4
6.5
1
PIN DESCRIPTIONS
Top View
10
V
V
V
V
V
0.4
Operating Power
Power-Down Current
NC
DVDD + 0.3
0.35 • DVDD
0.6
Offset Binary Two’s Complement
Quiescent Current
DVDD 9
UNITS
CMOS
POWER-SUPPLY REQUIREMENTS
Power Supply Voltage
ADS1254E
MAX
12 DGND
11 NC
3
TYPICAL CHARACTERISTICS
At TA = +25°C, AVDD = +5V, DVDD = +1.8V, CLK = 8MHz, and VREF = 4.096, unless otherwise specified.
EFFECTIVE RESOLUTION vs DATA OUTPUT RATE
20.0
1.9
19.8
1.8
19.6
Effective Resolution (Bits)
RMS Noise (ppm of FS)
RMS NOISE vs DATA OUTPUT RATE
2.0
1.7
1.6
1.5
1.4
1.3
1.2
1.1
19.4
19.2
19.0
18.8
18.6
18.4
18.2
1.0
100
1k
10k
18.0
100k
100
1k
Data Ouput Rate (Hz)
RMS NOISE vs TEMPERATURE
100k
EFFECTIVE RESOLUTION vs TEMPERATURE
2.0
20
1.8
19.8
1.6
19.6
Effective Resolution (Bits)
RMS Noise (ppm of FS)
10k
Data Ouput Rate (Hz)
1.4
1.2
1.0
0.8
0.6
0.4
0.2
19.4
19.2
19.0
18.8
18.6
18.4
18.2
0.0
18.0
–40
–20
0
20
40
60
80
100
–40
–20
0
Temperature (°C)
20
40
60
80
100
Temperature (°C)
RMS NOISE vs VREF Voltage
RMS NOISE vs VREF Voltage
10
12
9
10
RMS Noise (ppm of FS)
RMS Noise (µV)
8
7
6
5
4
3
2
8
6
4
2
1
0
0
0.5
1.0
1.5
2.0
2.5
3.0
VREF Voltage (V)
4
3.5
4.0
4.5
5.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5
VREF Voltage (V)
ADS1254
SBAS213
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, AVDD = +5V, DVDD = +1.8V, CLK = 8MHz, and VREF = 4.096, unless otherwise specified.
RMS NOISE vs INPUT VOLTAGE
INTEGRAL NONLINEARITY vs TEMPERATURE
RMS Noise (ppm of FS)
2
2.5
2.0
INL (ppm of FS)
1.5
1
1.5
1.0
0.5
0.5
0
–5
–4
–3
–2
–1
0
1
2
3
4
0
5
–40
–20
0
Input Voltage (V)
20
40
60
80
100
Temperature (°C)
OFFSET vs TEMPERATURE
INTEGRAL NON-LINEARITY vs DATA OUTPUT RATE
20
6
18
DC Offset (ppm of FS)
INL (ppm of FS)
5
4
3
2
1
16
14
12
10
8
6
4
2
0
0
100
1k
10k
–40
100k
–20
0
20
40
60
80
100
7
8
Temperature (°C)
Data Output Rate (Hz)
GAIN ERROR vs TEMPERATURE
PSR vs CLK FREQUENCY
600
–0
–10
–20
–30
560
PSR (dB)
Gain Error (ppm of FS)
580
540
520
–40
–50
–60
–70
500
–80
480
–100
–90
–60
–40
–20
0
20
40
Temperature (°C)
ADS1254
SBAS213
60
80
100
1
2
3
4
5
6
Clock Frequency (MHz)
5
TYPICAL CHARACTERISTICS (Cont.)
At TA = +25°C, AVDD = +5V, DVDD = +1.8V, CLK = 8MHz, and VREF = 4.096, unless otherwise specified.
CMR vs COMMON-MODE FREQUENCY
CMR AT 60Hz vs CLK FREQUENCY
–70
–50
–75
–80
CMR (dB)
CMR at 60Hz (dB)
–60
–70
–80
–85
–90
–90
–95
–100
–100
–110
–105
0
1
2
3
4
5
6
7
8
10
100
0.8
4.0
0.7
3.5
0.6
AVDD (5V)
DVDD (1.8V)
0.4
0.3
0.2
0.1
3.0
Analog (5V)
Digital (3.3V)
Digital (1.8V)
2.5
2.0
1.5
1.0
0
–20
0
20
40
60
80
100
0
1
2
Temperature (°C)
3
4
5
6
7
8
Clock Frequency (MHz)
TYPICAL FFT
(1kHz input at 0.1dB less than full-scale)
VREF CURRENT vs CLK FREQUENCY
35
0
30
–20
Relative Magnitude (dB)
VREF Current (µA)
100k
0.5
0
–40
25
20
15
10
5
–40
–60
–80
–100
–120
–140
–160
0
0
1
2
3
4
5
Clock Frequency (MHz)
6
10k
POWER DISSIPATION vs CLK FREQUENCY
4.5
Power Dissipation (mW)
Current (mA)
CURRENT vs TEMPERATURE
0.9
0.5
1k
Common-Mode Signal Frequency (Hz)
Clock Frequency (MHz)
6
7
8
0
1
2
3
4
5
6
7
8
9
10
11
Input Signal Frequency (kHz)
ADS1254
SBAS213
THEORY OF OPERATION
The ADS1254 is a precision, high-dynamic range, 24-bit,
delta-sigma, A/D converter capable of achieving very
high-resolution digital results at high data rates.
The analog-input signal is sampled at a rate determined by the
frequency of the system clock (CLK). The sampled analog
input is modulated by the delta-sigma A/D modulator, which
is followed by a digital filter. A sinc5 digital low-pass filter
processes the output of the delta-sigma modulator and writes
the result into the data-output register. The DOUT/DRDY pin
is pulled LOW, indicating that new data is available to be read
by the external microcontroller/microprocessor. As shown in
the block diagram, the main functional blocks of the ADS1254
are the fourth-order delta-sigma modulator, a digital filter,
control logic, and a serial interface. Each of these functional
blocks is described below.
ANALOG INPUT
The ADS1254 contains a fully differential analog input. In order
to provide low system noise, common-mode rejection of 102dB,
and excellent power-supply rejection, the design topology is
based on a fully differential switched-capacitor architecture. The
bipolar input voltage range is from –4.096V to +4.096V, when
the reference input voltage equals +4.096V. The bipolar range is
with respect to –VIN, and not with respect to GND.
Figure 1 shows the basic input structure of the ADS1254.
The impedance is directly related to the sampling frequency
of the input capacitor that is set by the CLK rate. Higher
CLK rates result in lower impedance, and lower CLK rates
result in higher impedance.
RSW
(1300Ω typical)
Internal
Circuitry
AIN
Modulator Frequency
= fMOD
CINT
(6pF typical)
VCM
FIGURE 1. Analog-Input Structure.
20.8kHz with a –3dB frequency of 4.24kHz. The –3dB
frequency scales with the system clock frequency.
To ensure the best linearity of the ADS1254, a fully differential signal is recommended.
INPUT MULTIPLEXER
The CHSEL1 and CHSEL0 pins are used to select the analog
input channel, as shown in Table I. The recommended
method for changing channels is to change them after the
conversion from the previous channel has been completed
and read. When a channel is changed, internal logic senses
the change on the falling edge of CLK and resets the
conversion process. The conversion data from the new
channel is valid on the first DRDY after the channel change.
When multiplexing inputs, it is possible to achieve sample
rates close to 4kHz. This is due to the fact that it requires five
internal conversion cycles for the data to fully settle. The
data also must be read before the channel is changed. The
DRDY signal indicates a valid result after the five cycles
have occurred.
BIPOLAR INPUT
CHSEL1
CHSEL0
CHANNEL
0
0
1
1
0
1
0
1
CH1
CH2
CH3
CH4
TABLE I. Channel Selection.
Each of the differential inputs of the ADS1254 must stay
between AGND and AVDD. With a reference voltage at less
than half of AVDD, one input can be tied to the reference
voltage, and the other input can range from AGND to
2 • VREF. By using a three op-amp circuit featuring a single
amplifier and four external resistors, the ADS1254 can be
configured to accept bipolar inputs referenced to ground.
The conventional ±2.5V, ±5V, and ±10V input ranges can
be interfaced to the ADS1254 using the resistor values
shown in Figure 2.
The input impedance of the analog input changes with the
ADS1254 system clock frequency (CLK). The relationship is:
R1
10kΩ
AIN Impedance (Ω) = (8MHz/CLK) • 125,000
With regard to the analog-input signal, the overall analog
performance of the device is affected by three items: first, the
input impedance can affect accuracy. If the source impedance
of the input signal is significant, or if there is passive filtering
prior to the ADS1254, a significant portion of the signal can be
lost across this external impedance. The magnitude of the
effect is dependent on the desired system performance.
Second, the current into or out of the analog inputs must be
limited. Under no conditions should the current into or out
of the analog inputs exceed 10mA.
Third, to prevent aliasing of the input signal, the analog-input
signal must be band limited. The bandwidth of the A/D
converter is a function of the system clock frequency. With a
system clock frequency of 8MHz, the data-output rate is
ADS1254
SBAS213
+IN
OPA4350
20kΩ
Bipolar
Input
–IN
ADS1254
VREF
R2
OPA4350
OPA4350
BIPOLAR INPUT
±10V
±5V
±2.5V
R1
R2
2.5kΩ
5kΩ
10kΩ
5kΩ
10kΩ
20kΩ
REF
2.5V
FIGURE 2. Level Shift Circuit for Bipolar Input Ranges.
7
DELTA-SIGMA MODULATOR
REFERENCE INPUT
The ADS1254 operates from a nominal system clock frequency of 8MHz. The modulator frequency is fixed in
relation to the system clock frequency. The system clock
frequency is divided by 6 to derive the modulator frequency.
Therefore, with a system clock frequency of 8MHz, the
modulator frequency is 1.333MHz. Furthermore, the
oversampling ratio of the modulator is fixed in relation to the
modulator frequency. The oversampling ratio of the modulator is 64, and with the modulator frequency running at
1.333MHz, the data rate is 20.8kHz. Using a slower system
clock frequency will result in a lower data output rate, as
shown in Table II.
Reference input takes an average current of 32µA with a
8MHz system clock. This current will be proportional to the
system clock. A buffered reference is recommended for the
ADS1254. The recommended reference circuit is shown in
Figure 3.
Reference voltages higher than 4.096V will increase the
full-scale range, while the absolute internal circuit noise of
the converter remains the same. This will decrease the noise
in terms of ppm of full scale, which increases the effective
resolution (see the Typical Characteristic “RMS Noise vs
VREF Voltage”).
CLK (MHz)
DATA OUTPUT RATE (Hz)
8(1)
7.372800(1)
6.144000(1)
6.000000(1)
4.915200(1)
3.686400(1)
3.072000(1)
2.457600(1)
1.843200(1)
0.921600
0.460800
0.384000
0.192000
0.038400
0.023040
0.019200
0.011520
0.009600
0.007680
0.006400
0.005760
0.004800
0.003840
20,833
19,200
16,000
15,625
12,800
9,600
8,000
6,400
4,800
2,400
1,200
1,000
500
100
60
50
30
25
20
16.67
15
12.50
10
DIGITAL FILTER
The digital filter of the ADS1254, referred to as a sinc5 filter,
computes the digital result based on the most recent outputs
from the delta-sigma modulator. At the most basic level, the
digital filter can be thought of as simply averaging the
modulator results in a weighted form and presenting this
average as the digital output. The digital output rate, or data
rate, scales directly with the system CLK frequency. This
allows the data output rate to be changed over a very wide
range (five orders of magnitude) by changing the system
CLK frequency. However, it is important to note that the
–3dB point of the filter is 0.2035 times the data output rate,
so the data output rate should allow for sufficient margin to
prevent attenuation of the signal of interest.
Since the conversion result is essentially an average, the
data-output rate determines the location of the resulting
notches in the digital filter (see Figure 4). Note that the first
notch is located at the data-output rate frequency, and
subsequent notches are located at integer multiples of the
data-output rate to allow for rejection of not only the
fundamental frequency, but also harmonic frequencies. In
this manner, the data-output rate can be used to set specific
notch frequencies in the digital filter response.
For example, if the rejection of power-line frequencies is
desired, then the data-output rate can simply be set to the
power-line frequency. For 50Hz rejection, the system CLK
NOTE: (1) Standard Clock Oscillator.
TABLE II. CLK Rate versus Data Output Rate.
+5V
+5V
0.10µF
7
4.99kΩ
2
To VREF
Pin 18 of
the ADS1254
6
10kΩ
3
1
OPA350
+
+
LM404-4.1
10µF
0.10µF
10µF
0.1µF
4
FIGURE 3. Recommended External Voltage Reference Circuit for Best Low-Noise Operation with the ADS1254.
8
ADS1254
SBAS213
DIGITAL FILTER RESPONSE
0
–20
–20
–40
–40
–60
–60
–80
–80
Gain (dB)
Gain (dB)
NORMALIZED DIGITAL FILTER RESPONSE
0
–100
–120
–100
–120
–140
–140
–160
–160
–180
–180
–200
–200
0
1
2
3
4
5
6
7
8
9
0
10
50
100
FIGURE 4. Normalized Digital Filter Response.
250
300
DIGITAL FILTER RESPONSE
0
0
–20
–20
–40
–40
–60
–60
–80
Gain (dB)
Gain (dB)
200
FIGURE 5. Digital Filter Response (50Hz).
DIGITAL FILTER RESPONSE
–100
–120
–80
–100
–120
–140
–140
–160
–160
–180
–180
–200
–200
0
50
100
150
200
250
0
300
10
20
30
Frequency (Hz)
40
50
60
70
80
90
100
53
54
55
Frequency (Hz)
FIGURE 6. Digital Filter Response (60Hz).
FIGURE 7. Digital Filter Response (10Hz).
DIGITAL FILTER RESPONSE
DIGITAL FILTER RESPONSE
0
0
–20
–20
–40
–40
–60
–60
–80
Gain (dB)
Gain (dB)
150
Frequency (Hz)
Frequency (Hz)
–100
–120
–80
–100
–120
–140
–140
–160
–160
–180
–180
–200
–200
45
46
47
48
49
50
51
52
53
54
55
Frequency (Hz)
FIGURE 8. Expanded Digital Filter Response (50Hz with a
50Hz Data Output Rate).
ADS1254
SBAS213
45
46
47
48
49
50
51
52
Frequency (Hz)
FIGURE 9. Expanded Digital Filter Response (50Hz with a
10Hz Data Output Rate).
9
DIGITAL FILTER RESPONSE
0
–20
–20
–40
–40
–60
–60
–80
–80
Gain (dB)
Gain (dB)
DIGITAL FILTER RESPONSE
0
–100
–120
–100
–120
–140
–140
–160
–160
–180
–180
–200
–200
55
56
57
58
59
60
61
62
63
64
65
Frequency (Hz)
55
56
57
58
59
60
61
62
63
64
65
Frequency (Hz)
FIGURE 10. Expanded Digital Filter Response (60Hz with
a 60Hz Data Output Rate).
FIGURE 11. Expanded Digital Filter Response (60Hz with
a 10Hz Data Output Rate).
frequency should be 19.200kHz, this will set the data-output
rate to 50Hz (see Table I and Figure 5). For 60Hz rejection,
the system CLK frequency should be 23.040kHz, this will set
the data-output rate to 60Hz (see Table I and Figure 6). If both
50Hz and 60Hz rejection is required, then the system CLK
should be 3.840kHz; this will set the data-output rate to 10Hz
and reject both 50Hz and 60Hz (See Table I and Figure 7).
There is an additional benefit in using a lower data-output
rate. It provides better rejection of signals in the frequency
band of interest. For example, with a 50Hz data-output rate,
a significant signal at 75Hz may alias back into the passband
at 25Hz. This is due to the fact that rejection at 75Hz may only
be 66dB in the stopband—frequencies higher than the firstnotch frequency (see Figure 5). However, setting the dataoutput rate to 10Hz will provide 135dB rejection at 75Hz (see
Figure 7). A similar benefit is gained at frequencies near the
data-output rate (see Figures 8, 9, 10, and 11). For example,
with a 50Hz data-output rate, rejection at 55Hz may only be
105dB (see Figure 8). However, with a 10Hz data-output rate,
rejection at 55Hz will be 122dB (see Figure 9). If a slower
data-output rate does not meet the system requirements, then
the analog front end can be designed to provide the needed
attenuation to prevent aliasing. Additionally, the data-output
rate may be increased and additional digital filtering may be
done in the processor or controller.
The digital filter is described by the following transfer function:
10
5
 π • f • 64 
sin

 fMOD 
H( f ) =
 π•f 
64 • sin

 fMOD 
or
 1 – z –64
H( z ) = 
 64 • 1 – z –1

(
)




5
The digital filter requires five conversions to fully settle. The
modulator has an oversampling ratio of 64, therefore, it
requires 5 • 64, or 320 modulator results, or clocks, to fully
settle. Since the modulator clock is derived from the system
clock (CLK) (modulator clock = CLK ÷ 6), the number of
system clocks required for the digital filter to fully settle is
5 • 64 • 6, or 1920 CLKs. This means that any significant
step change at the analog input requires five full conversions
to settle. However, if the step change at the analog input
occurs asynchronously to the DOUT/DRDY pulse, six conversions are required to ensure full settling.
ADS1254
SBAS213
CONTROL LOGIC
time defined by t4. If more than 24 SCLKs were provided
during DOUT mode, the DOUT/DRDY line would stay
LOW until the time defined by t4.
The internal data pointer for shifting data out on
DOUT/DRDY is reset on the falling edge of the time defined
by t1 and t4. This ensures that the first bit of data shifted out
of the ADS1254 after DRDY mode is always the MSB of
new data.
The control logic is used for communications and control of
the ADS1254.
Power-Up Sequence
Prior to power-up, all digital and analog-input pins must be
LOW. During power-up, these signal inputs should never
exceed +AVDD or +DVDD.
Once the ADS1254 powers up, the DOUT/DRDY line will
pulse LOW on the first conversion for which the data is valid
from the analog input signal.
SYNCHRONIZING MULTIPLE CONVERTERS
The normal state of SCLK is LOW, however, by holding
SCLK HIGH, multiple ADS1254s can be synchronized. This
is accomplished by holding SCLK HIGH for at least four, but
less than twenty, consecutive DOUT/DRDY cycles (see Figure 14). After the ADS1254 circuitry detects that SCLK has
been held HIGH for four consecutive DOUT/DRDY cycles,
the DOUT/DRDY pin will pulse LOW for 3 CLK cycles and
then be held HIGH, and the modulator will be held in a reset
state. The modulator will be released from reset and synchronization will occur on the falling edge of SCLK. With
multiple converters, the falling edge transition of SCLK must
occur simultaneously on all devices. It is important to note
that prior to synchronization, the DOUT/DRDY pulse of
multiple ADS1254s in the system could have a difference in
timing up to one DRDY period. Therefore, to ensure synchronization, the SCLK should be held HIGH for at least five
DRDY cycles. The first DOUT/DRDY pulse after the falling
edge of SCLK will occur at t14. The first DOUT/DRDY pulse
indicates valid data.
POWER-DOWN MODE
The normal state of SCLK is LOW, however, by holding
SCLK HIGH, the ADS1254 will enter power-down mode.
This is accomplished by holding SCLK HIGH for at least
twenty consecutive DOUT/DRDY periods (see Figure 15).
After the ADS1254 circuitry detects that SCLK has been
held HIGH for four consecutive DOUT/DRDY cycles, the
DOUT/DRDY pin will pulse LOW for 3 CLK cycles and
then be held HIGH, and the modulator will be held in a
reset state. If SCLK is held HIGH for an additional sixteen
DOUT/DRDY periods, the ADS1254 will enter
power-down mode. The part will be released from powerdown mode on the falling edge of SCLK. It is important to
note that the DOUT/DRDY pin will be held HIGH after four
DOUT/DRDY cycles, but power-down mode will not be
entered for an additional sixteen DOUT/DRDY periods. The
first DOUT/DRDY pulse after the falling edge of SCLK will
occur at t16 and will indicate valid data. Subsequent DOUT/
DRDY pulses will occur normally.
DOUT/DRDY
The DOUT/DRDY output signal alternates between two
modes of operation. The first mode of operation is the Data
Ready mode (DRDY) to indicate that new data has been
loaded into the data-output register and is ready to be read.
The second mode of operation is the Data Output (DOUT)
mode and is used to serially shift data out of the Data Output
Register (DOR). The time domain partitioning of the DRDY
and DOUT function as shown in Figure 12.
See Figure 13 for the basic timing of DOUT/DRDY. During
the time defined by t2, t3, and t4, the DOUT/DRDY pin
functions in DRDY mode. The state of the DOUT/DRDY
pin would be HIGH prior to the internal transfer of new data
to the DOR. The result of the A/D conversion would be
written to the DOR from MSB to LSB in the time defined by
t1 (see Figures 12 and 13). The DOUT/DRDY line would
then pulse LOW for the time defined by t2, and then pulse
HIGH for the time defined by t3 to indicate that new data
was available to be read. At this point, the function of the
DOUT/DRDY pin would change to DOUT mode. Data
would be shifted out on the pin after t7. The device communicating with the ADS1254 can provide SCLKs to the
ADS1254 after the time defined by t6. The normal mode of
reading data from the ADS1254 would be for the device
reading the ADS1254 to latch the data on the rising edge of
SCLK (since data is shifted out of the ADS1254 on the
falling edge of SCLK). In order to retrieve valid data, the
entire DOR must be read before the DOUT/DRDY pin
reverts back to DRDY mode.
If SCLKs were not provided to the ADS1254 during the
DOUT mode, the MSB of the DOR would be present on the
DOUT/DRDY line until the time defined by t4. If an incomplete read of the ADS1254 took place while in DOUT mode
(i.e., less than 24 SCLKs were provided), the state of the last
bit read would be present on the DOUT/DRDY line until the
DOUT Mode
DRDY Mode
t2
t4
DOUT/DRDY
DOUT Mode
DATA
DRDY Mode
t3
DATA
DATA
t1
FIGURE 12. DOUT/DRDY Partitioning.
ADS1254
SBAS213
11
SERIAL INTERFACE
The ADS1254 includes a simple serial interface that can be
connected to microcontrollers and digital signal processors
in a variety of ways. Communications with the ADS1254
can commence on the first detection of the DOUT/DRDY
pulse after power up.
It is important to note that the data from the ADS1254 is a
24-bit result transmitted MSB-first in Offset Two’s Complement format, as shown in Table IV.
The data must be clocked out before the ADS1254 enters
DRDY mode to ensure reception of valid data, as described
in the DOUT/DRDY section of this data sheet.
ISOLATION
The serial interface of the ADS1254 provides for simple
isolation methods. The CLK signal can be local to the
ADS1254, which then only requires two signals (SCLK and
DOUT/DRDY) to be used for isolated data acquisition. The
channel select signals (CHSEL0, CHSEL1) will also need to
be isolated unless a counter is used to auto multiplex the
channels.
DIFFERENTIAL VOLTAGE INPUT
DIGITAL OUTPUT (HEX)
+Full Scale
Zero
–Full Scale
7FFFFFH
000000H
800000H
TABLE IV. ADS1254 Data Format (Offset Two's Complement).
SYMBOL
tOSC
tDRDY
DRDY Mode
DOUT Mode
t1
t2
t3
t4
t5
t6
t7
t8
t9
t10
t11
t12
t13
t14
t15
t16
t17
t18
DESCRIPTION
MIN
CLK Period
Conversion Cycle
DRDY Mode
DOUT Mode
DOR Write Time
DOUT/DRDY LOW Time
DOUT/DRDY HIGH Time (Prior to Data Out)
DOUT/DRDY HIGH Time (Prior to Data Ready)
Rising Edge of CLK to Falling Edge of DOUT/DRDY
End of DRDY Mode to Rising Edge of First SCLK
End of DRDY Mode to Data Valid (Propagation Delay)
Falling Edge of SCLK to Data Valid (Hold Time)
Falling Edge of SCLK to Next Data Out Valid (Propagation Delay)
SCLK Setup Time for Synchronization or Power Down
DOUT/DRDY Pulse for Synchronization or Power Down
Rising Edge of SCLK Until Start of Synchronization
Synchronization Time
Falling Edge of CLK (After SCLK Goes Low) Until Start of DRDY Mode
Rising Edge of SCLK Until Start of Power Down
Falling Edge of CLK (After SCLK Goes Low) Until Start of DRDY Mode
Falling Edge of Last DOUT/DRDY to Start of Power Down
DOUT/DRDY High Time After Mux Change.
125
TYP
MAX
384 • tOSC
36 • tOSC
348 • tOSC
6 • tOSC
6 • tOSC
6 • tOSC
24 • tOSC
50
30
50
5
50
30
3 • tOSC
1537 • CLK
0.5 • CLK
7679 • CLK
6143.5 • CLK
2042.5 • tOSC
7681 • CLK
2318.5 • tOSC
6144.5 • tOSC
2043.5 • tosc
UNITS
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
TABLE III. Digital Timing.
t18
DOUT/DRDY
DATA
DATA
CHSEL0, CHSEL1
MUX CHANGE
FIGURE 13. Multiplexer Operation.
12
ADS1254
SBAS213
ADS1254
SBAS213
13
t4
t1
t10
t2
t3
tDRDY
t10
t2
t3
FIGURE 16. Power-Down Mode.
DOUT/DRDY
SCLK
CLK
tDRDY
FIGURE 15. Synchronization Mode.
DOUT/DRDY
SCLK
CLK
FIGURE 14. DOUT/DRDY Timing.
DOUT/DRDY
SCLK
CLK
t2
DOUT
Mode
DATA
DOUT
Mode
DATA
t4
t4
DRDY Mode
t5
4 tDRDY
4 tDRDY
t12
t3
t15
t11
MSB
t7
t6
DATA
DATA
t8
t9
tDRDY
t11
t11
t17
t13
t16
Power Down Occurs Here
t14
Synchronization Begins Here
Synchronization Mode Starts Here
DOUT Mode
LSB
t2
t2
t3
t3
DATA
DATA
tDRDY
DOUT
Mode
tDRDY
DOUT
Mode
t4
t4
LAYOUT
POWER SUPPLY
The power supply should be well regulated and low noise.
For designs requiring very high resolution from the ADS1254,
power-supply rejection will be a concern. Avoid running
digital lines under the device as they may couple noise onto
the die. High-frequency noise can capacitively couple into
the analog portion of the device and will alias back into the
passband of the digital filter, affecting the conversion result.
This clock noise will cause an offset error.
GROUNDING
The analog and digital sections of the system design should
be carefully and cleanly partitioned. Each section should
have its own ground plane with no overlap between them.
AGND should be connected to the analog ground plane, as
well as all other analog grounds. Do not join the analog and
digital ground planes on the board, but instead connect the
two with a moderate signal trace. For multiple converters,
connect the two ground planes at one location as central to
all of the converters as possible. In some cases, experimentation may be required to find the best point to connect the
two planes together. The printed circuit board can be designed to provide different analog/digital ground connections via short jumpers. The initial prototype can be used to
establish which connection works best.
DECOUPLING
Good decoupling practices should be used for the ADS1254
and for all components in the design. All decoupling capacitors, and specifically the 0.1µF ceramic capacitors, should
be placed as close as possible to the pin being decoupled. A
1µF to 10µF capacitor, in parallel with a 0.1µF ceramic
capacitor, should be used to decouple Supply to ground.
SYSTEM CONSIDERATIONS
The recommendations for power supplies and grounding
will change depending on the requirements and specific
design of the overall system. Achieving 24 bits of noise
performance is a great deal more difficult than achieving 12
bits of noise performance. In general, a system can be
broken up into four different stages:
•
•
•
•
Analog Processing
Analog Portion of the ADS1254
Digital Portion of the ADS1254
Digital Processing
For the simplest system consisting of minimal analog signal
processing (basic filtering and Gain), a microcontroller, and
one clock source, one can achieve high resolution by powering all components by a common power supply. In addition, all components could share a common ground plane.
Thus, there would be no distinctions between “analog”
power and ground, and “digital” power and ground. The
layout should still include a power plane, a ground plane,
and careful decoupling. In a more extreme case, the design
14
could include:
• Multiple ADS1254s
• Extensive Analog Signal Processing
• One or More Microcontrollers, Digital Signal Processors,
or Microprocessors
• Many Different Clock Sources
• Interconnections to Various Other Systems
High resolution will be very difficult to achieve for this
design. The approach would be to break the system into as
many different parts as possible. For example, each ADS1254
may have its own “analog” processing front end.
DEFINITION OF TERMS
An attempt has been made to be consistent with the terminology used in this data sheet. In that regard, the definition
of each term is given as follows:
Analog-Input Differential Voltage—for an analog signal
that is fully differential, the voltage range can be compared
to that of an instrumentation amplifier. For example, if both
analog inputs of the ADS1254 are at 2.048V, the differential voltage is 0V. If one analog input is at 0V and the other
analog input is at 4.096V, then the differential voltage
magnitude is 4.096V. This is the case regardless of which
input is at 0V and which is at 4.096V. The digital-output
result, however, is quite different. The analog-input differential voltage is given by the following equation:
+VIN – (–VIN)
A positive digital output is produced whenever the
analog-input differential voltage is positive, while a negative digital output is produced whenever the differential is
negative. For example, a positive full-scale output is produced when the converter is configured with a 4.096V
reference, and the analog-input differential is 4.096V. The
negative full-scale output is produced when the differential
voltage is –4.096V. In each case, the actual input voltages
must remain within the –0.3V to +AVDD range.
Actual Analog-Input Voltage—the voltage at any one
analog input relative to AGND.
Full-Scale Range (FSR)—as with most A/D Converters,
the full-scale range of the ADS1254 is defined as the “input”
that produces the positive full-scale digital output minus the
“input” that produces the negative full-scale digital output.
For example, when the converter is configured with a 4.096V
reference, the differential full-scale range is:
[4.096V (positive full scale) – (–4.096V) (negative full scale)] =
8.192V
Least Significant Bit (LSB) Weight—this is the theoretical amount of voltage that the differential voltage at the
analog input would have to change in order to observe a
change in the output data of one least significant bit. It is
computed as follows:
LSB Weight =
Full – Scale Range 2 • VREF
= N
2N – 1
2 –1
where N is the number of bits in the digital output.
ADS1254
SBAS213
Conversion Cycle—as used here, a conversion cycle refers
to the time period between DOUT/DRDY pulses.
Effective Resolution (ER)—of the ADS1254 in a particular
configuration can be expressed in two different units:
bits rms (referenced to output) and µVrms (referenced to
input). Computed directly from the converter's output data,
each is a statistical calculation based on a given number of
results. Noise occurs randomly; the rms value represents a
statistical measure that is one standard deviation. The ER in
bits can be computed as follows:
2 • VREF 
20 • log
 Vrms noise 
ER in bits rms =
6.02
The 2 • VREF figure in each calculation represents the
full-scale range of the ADS1254. This means that both units
are absolute expressions of resolution—the performance in
different configurations can be directly compared, regardless of the units.
fMOD—frequency of the modulator and the frequency the
input is sampled.
fMOD =
CLK Frequency
6
Noise Reduction—for random noise, the ER can be improved with averaging. The result is the reduction in noise by
the factor √N, where N is the number of averages, as shown
in Table V. This can be used to achieve true 24-bit performance at a lower data rate. To achieve 24 bits of resolution,
more than 24 bits must be accumulated. A 36-bit accumulator
is required to achieve an ER of 24 bits. Table V uses VREF =
4.096V, with the ADS1254 outputting data at 20kHz, a 4096
point average will take 204.8ms. The benefits of averaging
will be degraded if the input signal drifts during that 200ms.
N
(Number
of Averages)
NOISE
REDUCTION
FACTOR
ER
IN
Vrms
ER
IN
BITS rms
1
2
4
8
16
32
64
128
256
512
1024
2048
4096
1
1.414
2
2.82
4
5.66
8
11.3
16
22.6
32
45.25
64
14.6µV
10.3µV
7.3µV
5.16µV
3.65µV
2.58µV
1.83µV
1.29µV
0.91µV
0.65µV
0.46µV
0.32µV
0.23µV
19.1
19.6
20.1
20.6
21.1
21.6
22.1
22.6
23.1
23.6
24.1
24.6
25.1
TABLE V. Averaging.
fDATA—Data output rate.
fDATA =
ADS1254
SBAS213
fMOD CLK Frequency
=
64
384
15
PACKAGE OPTION ADDENDUM
www.ti.com
9-Dec-2004
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
ADS1254E
ACTIVE
SSOP/
QSOP
DBQ
20
56
None
CU SNPB
Level-3-250C-168 HR
ADS1254E/2K5
ACTIVE
SSOP/
QSOP
DBQ
20
2500
None
CU SNPB
Level-3-250C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - May not be currently available - please check http://www.ti.com/productcontent for the latest availability information and additional
product content details.
None: Not yet available Lead (Pb-Free).
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean "Pb-Free" and in addition, uses package materials that do not contain halogens,
including bromine (Br) or antimony (Sb) above 0.1% of total product weight.
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDECindustry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2004, Texas Instruments Incorporated
Similar pages