MC10EL11, MC100EL11 5.0V ECL 1:2 Differential Fanout Buffer The MC10EL/100EL11 is a differential 1:2 fanout buffer. The device is functionally similar to the E111 device but with higher performance capabilities. The within-device skew and propagation delay is significantly improved over the E111. The differential inputs of the EL11 employ clamping circuitry to maintain stability under open input conditions. If the inputs are left open (pulled to VEE) the Q outputs will go LOW. The 100 Series contains temperature compensation. Features • • • • • • www.onsemi.com 8 8 1 1 SOIC−8 D SUFFIX CASE 751−07 265 ps Propagation Delay 5 ps Skew Between Outputs TSSOP−8 DT SUFFIX CASE 948R−02 PECL Mode Operating Range: VCC = 4.2 V to 5.7 with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = −4.2 V to −5.7 V MARKING DIAGRAMS* Internal Input Pulldown Resistors These Devices are Pb-Free, Halogen Free and are RoHS Compliant Q0 1 Q0 2 Q1 3 Q1 8 7 8 8 HEL11 ALYW G VCC 1 1 8 8 D KEL11 ALYW G 6 5 4 1 D Table 1. PIN DESCRIPTION FUNCTION D, D Q0, Q0; Q1, Q1 VCC VEE ECL Data Inputs ECL Data Outputs Positive Supply Negative Supply © Semiconductor Components Industries, LLC, 2016 July, 2016− Rev. 11 L Y W M G KL11 ALYWG G = Wafer Lot = Year = Work Week = Date Code = Pb-Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. Figure 1. Logic Diagram and Pinout Assignment PIN 1 H = MC10 K = MC100 4Q = MC10 2E = MC100 A = Assembly Location VEE HL11 ALYWG G ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 6 of this data sheet. 1 Publication Order Number: MC10EL11/D MC10EL11, MC100EL11 Table 2. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 KW Internal Input Pullup Resistor N/A ESD Protection Human Body Model Machine Model > 1 KV > 100 V Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) Pb-Free Pkg SOIC−8 TSSOP−8 Level 1 Level 3 Flammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in Transistor Count 44 Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. Table 3. MAXIMUM RATINGS Symbol Rating Unit VCC PECL Mode Power Supply Parameter VEE = 0 V Condition 1 Condition 2 8 V VEE NECL Mode Power Supply VCC = 0 V −8 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 −6 V Iout Output Current Continuous Surge 50 100 mA VI ≤ VCC VI ≥ VEE TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm SOIC−8 190 130 °C/W qJC Thermal Resistance (Junction-to-Case) Standard Board SOIC−8 41 to 44 °C/W qJA Thermal Resistance (Junction-to-Ambient) 0 lfpm 500 lfpm TSSOP−8 185 140 °C/W qJC Thermal Resistance (Junction-to-Case) Standard Board TSSOP−8 41 to 44 ± 5% °C/W Tsol Wave Solder (Pb-Free) <2 to 3 sec @ 260°C 265 °C Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. JEDEC standard multilayer board − 2S2P (2 signal, 2 power) www.onsemi.com 2 MC10EL11, MC100EL11 Table 4. 10EL SERIES PECL DC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V (Note 1)) −40°C Symbol Characteristic Min 25°C Typ Max 26 31 Min 85°C Typ Max 26 31 Min Typ Max Unit 26 31 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 2) 3920 4010 4110 4020 4105 4190 4090 4185 4280 mV VOL Output LOW Voltage (Note 2) 3050 3200 3350 3050 3210 3370 3050 3227 3405 mV VIH Input HIGH Voltage (Single-Ended) 3770 4110 3870 4190 3940 4280 mV VIL Input LOW Voltage (Single-Ended) 3050 3500 3050 3520 3050 3555 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 3) 2.5 4.6 2.5 4.6 2.5 4.6 V 150 mA IIH Input HIGH Current IIL Input LOW Current 150 0.5 150 0.5 0.3 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.25 V / −0.5 V. 2. Outputs are terminated through a 50ĂW resistor to VCC − 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. Table 5. 10EL SERIES NECL DC CHARACTERISTICS (VCC = 0.0 V; VEE = −5.0 V (Note 1)) −40°C Symbol Characteristic Typ Max 26 31 Max 26 31 −1080 −990 −890 −980 −895 −810 Output LOW Voltage (Note 2) −1950 −1800 −1650 −1950 −1790 VIH Input HIGH Voltage (Single-Ended) −1230 −890 VIL Input LOW Voltage (Single-Ended) −1950 VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 3) −2.5 Power Supply Current VOH Output HIGH Voltage (Note 2) VOL IIH Input HIGH Current IIL Input LOW Current Min 85°C Typ IEE Min 25°C Typ Max Unit 26 31 mA −910 −815 −720 mV −1630 −1950 −1773 −1595 mV −1130 −810 −1060 −720 mV −1500 −1950 −1480 −1950 −1445 mV −0.4 −2.5 −0.4 −2.5 −0.4 V 150 mA 150 0.5 Min 150 0.5 0.3 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.25 V / −0.5 V. 2. Outputs are terminated through a 50ĂW resistor to VCC − 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. www.onsemi.com 3 MC10EL11, MC100EL11 Table 6. 100EL SERIES PECL DC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V (Note 1)) −40°C Symbol Characteristic Min 25°C Typ Max 26 31 Min 85°C Typ Max 26 31 Min Typ Max Unit 30 36 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 2) 3915 3995 4120 3975 4045 4120 3975 4050 4120 mV VOL Output LOW Voltage (Note 2) 3170 3305 3445 3190 3295 3380 3190 3295 3380 mV VIH Input HIGH Voltage (Single-Ended) 3835 4120 3835 4120 3835 4120 mV VIL Input LOW Voltage (Single-Ended) 3190 3525 3190 3525 3190 3525 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 3) 2.5 4.6 2.5 4.6 2.5 4.6 V 150 mA IIH Input HIGH Current IIL Input LOW Current 150 0.5 150 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V. 2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. Table 7. 100EL SERIES NECL DC CHARACTERISTICS (VCC = 0.0 V; VEE = −5.0 V (Note 1)) −40°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current 26 31 26 31 30 36 mA VOH Output HIGH Voltage (Note 2) −1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV VOL Output LOW Voltage (Note 2) −1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV VIH Input HIGH Voltage (Single-Ended) −1165 −880 −1165 −880 −1165 −880 mV VIL Input LOW Voltage (Single-Ended) −1810 −1475 −1810 −1475 −1810 −1475 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 3) −2.5 −0.4 −2.5 −0.4 −2.5 −0.4 V 150 mA IIH Input HIGH Current IIL Input LOW Current 150 0.5 150 0.5 0.5 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary +0.8 V / −0.5 V. 2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. 3. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. www.onsemi.com 4 MC10EL11, MC100EL11 Table 8. AC CHARACTERISTICS (VCC = 5.0 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −5.0 V (Note 1)) −40°C Symbol Characteristic Min fmax Maximum Toggle Frequency tPLH tPHL Propagation Delay to Output tSKEW Within-Device Skew (Note 2) Duty Cycle Skew (Note 3) tJITTER Random Clock Jitter (RMS) VPP tr tf 25°C Typ Max Min 85°C Typ Max Min Typ Max 1.5 135 260 385 190 5 GHz 265 340 5 20 215 29*0 365 ps 5 20 ps 0.6 Input Swing (Note 4) 150 Output Rise/Fall Times Q (20% − 80%) 100 1000 150 350 100 225 Unit ps 225 1000 150 350 100 225 1000 mV 350 ps NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. 10 Series: VEE can vary +0.25 V / −0.5 V. 100 Series: VEE can vary +0.8 V / −0.5 V. 2. Within-device skew defined as identical transitions on similar paths through a device. 3. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device. 4. VPP(min) is minimum input swing for which AC parameters guaranteed. The device has a DC gain of ≈ 40. Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VCC − 3.0 V Figure 2. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) www.onsemi.com 5 MC10EL11, MC100EL11 ORDERING INFORMATION Package Shipping† MC10EL11DG SOIC−8 (Pb-Free) 98 Units / Rail MC10EL11DR2G SOIC−8 (Pb-Free) 2500 / Tape & Reel MC10EL11DTG TSSOP−8 (Pb-Free) 100 Units / Rail MC100EL11DG SOIC−8 (Pb-Free) 98 Units / Rail MC100EL11DR2G SOIC−8 (Pb-Free) 2500 / Tape & Reel MC100EL11DTG TSSOP−8 (Pb-Free) 100 Units / Rail MC100EL11DTR2G TSSOP−8 (Pb-Free) 2500 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices www.onsemi.com 6 MC10EL11, MC100EL11 PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE AK −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 0.25 (0.010) M Y M 1 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 7 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC10EL11, MC100EL11 PACKAGE DIMENSIONS TSSOP−8 CASE 948R−02 ISSUE A 8x 0.15 (0.006) T U 0.10 (0.004) S 2X L/2 L 8 5 1 PIN 1 IDENT 0.15 (0.006) T U K REF M T U V S 0.25 (0.010) B −U− 4 M A −V− S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. S F DETAIL E C 0.10 (0.004) −T− SEATING PLANE D −W− G DETAIL E DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0_ 6_ INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0_ 6_ ECLinPS is a registered trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10EL11/D