Exar CDK8307BILP64 12/13-bit, 20/40/50/65/80msps, eight channel, ultra low power adc with lvd Datasheet

Data Sheet
CDK8307
– 23mW/channel at 20MSPS
– 35mW/channel at 40MSPS
– 41mW/channel at 50MSPS
– 51mW/channel at 65MSPS
– 59mW/channel at 80MSPS
n
72.2dB SNR at 8MHz FIN
n
0.5μs startup time from Sleep
n
15μs startup time from Power Down
n
Internal reference circuitry requires no
external components
n
Internal offset correction
n
Reduced power dissipation modes available
– 34mW/channel at 50MSPS
– 71.5dB SNR at 8MHz FIN
n
Coarse and fine gain control
n
1.8V supply voltage
n
Serial LVDS output
– 12- and 14-bit output available
An integrated PLL multiplies the input sampling clock by a factor of 12 or 14,
according to the LVDS output setting. The multiplied clock is used for data
serialization and data output. Data and frame synchronization output clocks are
supplied for data capture at the receiver.
Various modes and configuration settings can be applied to the ADC through
the serial control interface (SPI). Each channel can be powered down independently and data format can be selected through this interface. A full chip
idle mode can be set by a single external pin. Register settings determines the
exact function of this external pin.
The CDK8307 is designed to easily interface with field-programmable gate
arrays (FPGAs) from several vendors.
The very low startup times of the CDK8307 allow significant power reduction
in duty-cycled systems, by utilizing the Sleep Mode or Power Down Mode when
the receive path is idle.
Block Diagram
Package alternatives
RESETN
n
The CDK8307 is a high performance low power octal analog-to-digital
converter (ADC). The ADC employs internal reference circuitry, a serial control
interface and serial LVDS output data, and is based on a proprietary structure.
– TQFP-80
– QFN-64
APPLICATIONS
n
Medical Imaging
n
Wireless Infrastructure
IP1
n
Test and Measurement
IN1
n
Instrumentation
IP2
IN2
Exar Corporation
48720 Kato Road, Fremont CA 94538, USA
Clock
Input
PLL
LVDS
FCLKP
FCLKN
LCLKP
LCLKN
ADC
Digital
Gain
LVDS
D1N
D1P
ADC
Digital
Gain
LVDS
D2N
D2P
•
•
•
•
•
•
•
•
•
ADC
Digital
Gain
LVDS
D8N
D8P
www.exar.com
Tel. +1 510 668-7000 - Fax. +1 510 668-7001
Rev 1C
IP8
IN8
Serial Control
Interface
AVDD
AVSS
DVDD
DVSS
Low Power Dissipation
PD
n
General Description
CLKP
CLKN
20/40/50/65/80MSPS max sampling rate
SCLK
SDATA
n
CSN
FEATURES
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
12/13-bit, 20/40/50/65/80MSPS, Eight Channel,
Ultra Low Power ADC with LVDS
Data Sheet
Table of Contents
Features................................................................... 1
Table 6. LVDS Output Drive Strength for
Table 7. LVDS Internal Termination
Applications............................................................. 1
General Description................................................. 1
LCLK, FCLK, and Data................................ 19
Programmability........................................ 20
Table 8. LVDS Output Internal Termination............... 20
Table of Contents.................................................... 2
Table 9. Analog Input Invert.................................... 20
Table 10. LVDS Test Patterns................................... 21
Ordering Information.............................................. 3
Table 11. Programmable Gain.................................. 21
Pin Configurations................................................... 4
Table 12. Gain Setting for Channels 1-8................... 22
Pin Assignments................................................... 5-8
Absolute Maximum Ratings.................................... 9
Reliability Information............................................ 9
Table 13. LVDS Clock Programmability and
Data Output Modes.................................. 22
Figure 6. Phase Programmability Modes for LCLK...... 23
ESD Protection......................................................... 9
Figure 7. SDR Interface Modes................................ 23
Recommended Operating Conditions..................... 9
Table 14. Number of Serial Output Bits.................... 23
Electrical Characteristics....................................... 10
Figure 8. LVDS Output Timing Adjustment............... 24
Electrical Characteristics – CDK8307A.............10-11
Table 15. Full Scale Control..................................... 24
Electrical Characteristics – CDK8307B................. 11
Electrical Characteristics – CDK8307C.............11-12
Electrical Characteristics – CDK8307D.............12-13
Table 16. Register Values with Corresponding
Charge in Full-Scale Range....................... 25
Table 17. Clock Frequency....................................... 25
Electrical Characteristics – CDK8307E................. 13
Table 18. Clock Frequency Settings.......................... 25
Digital and Timing Electrical Characteristics...13-14
Table 19. Performance Control................................ 25
LVDS Timing Diagrams.......................................... 15
Table 20. Performance Control Settings.................... 26
Figure 1. 12-bit Output, DDR Mode.......................... 15
Table 21. External Common Mode Voltage
Figure 2. 14-bit Output, DDR Mode.......................... 15
Buffer Driving Strength............................ 26
Figure 3. 12-bit Output, SDR Mode.......................... 15
Theory of Operation.............................................. 27
Figure 4. Data Timing............................................. 15
Recommended Usage............................................ 27
Serial Interface...................................................... 16
Analog Input.......................................................... 27
Timing Diagram..................................................... 16
Figure 9. Input Configuration Diagram................. 27
Figure 5. Serial Port Interface Timing Diagram...... 16
DC-Coupling........................................................... 27
Table 1. Serial Port Interface Timing Definitions.... 16
Figure 10. DC-Coupled Input............................... 27
Register Initialization.............................................. 16
AC-Coupling........................................................... 28
Serial Register Map...........................................17-18
Figure 11. Transformer Coupled Input.................. 28
Table 2. Summary of Functions Supported
Figure 12. AC-Coupled Input............................... 28
Figure 13. Alternative Input Network.................... 28
Description of Serial Registers.........................18-25
Clock Input and Jitter Considerations....................... 29
Table 3. Software Reset.......................................... 18
Mechanical Dimensions ....................................30-31
Table 4. Power-Down Modes................................... 18
QFN-64 Package.................................................... 30
Table 5. LVDS Drive Strength Programmability.......... 19
TQFP-80 Package................................................... 31
©2009-2013 Exar Corporation 2/31
Rev 1C
Rev 1C
by Serial Interface.................................17-18
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Block Diagram......................................................... 1
Data Sheet
Ordering Information
Speed
Package
Pb-Free
RoHS Compliant
Operating Temperature Range
Packaging Method
CDK8307AITQ80
20MSPS
TQFP-80
Yes
Yes
-40°C to +85°C
Tray
CDK8307AILP64
20MSPS
QFN-64
Yes
Yes
-40°C to +85°C
Tray
CDK8307BITQ80
40MSPS
TQFP-80
Yes
Yes
-40°C to +85°C
Tray
CDK8307BILP64
40MSPS
QFN-64
Yes
Yes
-40°C to +85°C
Tray
CDK8307CITQ80
50MSPS
TQFP-80
Yes
Yes
-40°C to +85°C
Tray
CDK8307CILP64
50MSPS
QFN-64
Yes
Yes
-40°C to +85°C
Tray
CDK8307DITQ80
65MSPS
TQFP-80
Yes
Yes
-40°C to +85°C
Tray
CDK8307DILP64
65MSPS
QFN-64
Yes
Yes
-40°C to +85°C
Tray
CDK8307EITQ80
80MSPS
TQFP-80
Yes
Yes
-40°C to +85°C
Tray
CDK8307EILP64
80MSPS
QFN-64
Yes
Yes
-40°C to +85°C
Tray
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Part Number
Moisture sensitivity level for QFN package is MSL-2A, for TQFP package is MSL-3.
Rev 1C
©2009-2013 Exar Corporation 3/31
Rev 1C
Data Sheet
Pin Configurations
NC
AVDD
NC
54
AVDD
NC
55
49
AVDD
56
NC
CLKP
57
50
CLKN
58
51
OVDD
59
VCM
CSN
60
TP
AVSS
SDATA
61
52
SCLK
62
53
RESETN
63
IP1
1
48
IN8
IN1
2
47
IP8
AVSS
3
46
AVSS
IP2
4
45
IN7
IN2
5
44
IP7
AVSS
6
43
AVSS
IP3
7
42
IN6
IN3
8
41
IP6
AVSS
9
40
AVSS
IP4
10
39
IN5
IN4
11
38
IP5
DVSS
12
37
AVSS
PD
13
36
DVSS
DVSS
14
35
DVDD
D1P
15
34
D8N
D1N
16
33
D8P
CDK8307
NC
TP
AVSS
62
61
32
D7N
AVDD
31
63
30
D7P
NC
64
D6N
VCM
65
29
D6P
NC
66
28
NC
D5N
AVSS
67
27
D5P
68
26
NC
LCLKN
AVDD
69
25
LCLKP
70
24
CLKP
71
FCLKN
CLKN
72
23
FCLKP
AVSS
73
22
D4N
74
21
AVSS
D4P
OVDD
75
20
D3N
CSN
76
19
D3P
SDATA
77
18
SCLK
78
17
AVSS
79
D2P
AVSS
80
D2N
QFN-64
AVDD
1
60
AVDD
IP1
2
59
IN8
IN1
3
58
IP8
AVSS
4
57
AVSS
IP2
5
56
IN7
IN2
6
55
IP7
AVDD
7
54
AVDD
AVSS
8
53
AVSS
IP3
9
52
IN6
IN3
10
51
IP6
AVSS
11
50
AVSS
IP4
12
49
IN5
IN4
13
48
IP5
AVDD
14
47
AVDD
DVSS
15
46
DVSS
PD
16
45
RESETN
DVSS
17
44
DVSS
DVSS
18
43
DVSS
LCLKP
19
42
FCLKN
LCLKN
20
41
FCLKP
CDK8307
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
D1P
D2P
D2N
DVDD
DVSS
D3P
D3N
D4P
D4N
D5P
D5N
D6P
D6N
DVDD
DVSS
D7P
D7N
D8P
D8N
©2009-2013 Exar Corporation 4/31
Rev 1C
D1N
TQFP-80
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
TQFP-80
64
QFN-64
Rev 1C
Data Sheet
Pin Assignments - QFN
Pin No.
Pin Name
Description
49, 50, 57
AVDD
Analog power supply, 1.8V
3, 6, 9, 37, 40, 43, 46
AVSS
Analog ground
1
IP1
Positive differential input signal, channel 1
2
IN1
Negative differential input signal, channel 1
4
IP2
Positive differential input signal, channel 2
5
IN2
Negative differential input signal, channel 2
7
IP3
Positive differential input signal, channel 3
8
IN3
Negative differential input signal, channel 3
10
IP4
Positive differential input signal, channel 4
11
IN4
Negative differential input signal, channel 4
38
IP5
Positive differential input signal, channel 5
39
IN5
Negative differential input signal, channel 5
41
IP6
Positive differential input signal, channel 6
42
IN6
Negative differential input signal, channel 6
44
IP7
Positive differential input signal, channel 7
45
IN7
Negative differential input signal, channel 7
47
IP8
Positive differential input signal, channel 8
48
IN8
Negative differential input signal, channel 8
12, 14, 36
DVSS
Digital ground
35
DVDD
Digital and I/O power supply, 1.8V
13
PD
Power-down input. Activate after applying power in order to initialize the
ADC correctly. Alternatively use the SPI power down feature.
15
D1P
LVDS channel 1, positive output
16
D1N
LVDS channel 1, negative output
17
D2P
LVDS channel 2, positive output
18
D2N
LVDS channel 2, negative output
19
D3P
LVDS channel 3, positive output
20
D3N
LVDS channel 3, negative output
21
D4P
LVDS channel 4, positive output
22
D4N
LVDS channel 4, negative output
27
D5P
LVDS channel 5, positive output
28
D5N
LVDS channel 5, negative output
29
D6P
LVDS channel 6, positive output
30
D6N
LVDS channel 6, negative output
31
D7P
LVDS channel 7, positive output
32
D7N
LVDS channel 7, negative output
33
D8P
LVDS channel 8, positive output
34
D8N
LVDS channel 8, negative output
23
FCLKP
LVDS frame clock (1x), positive output
24
FCLKN
LVDS frame clock (1x), negative output
25
LCLKP
LVDS bit clock, positive output
QFN-64
Rev 1C
5/31
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
©2009-2013 Exar Corporation Rev 1C
Data Sheet
Pin Assignments QFN (Continued)
Pin No.
Pin Name
Description
LCLKN
NC
LVDS bit clock, negative output
Not connected
52
TP
Test pin. Leave open (un-connected) or connect to GND.
53
VCM
Common mode output pin, 0.5 AVDD
58
CLKP
Positive differential input clock
59
CLKN
Negative differential input clock.
60
OVDD
Digital CMOS inputs supply voltage (1.7V to 3.6V)
61
CSN
62
SDATA
Serial data input
63
SCLK
Serial clock input
64
RESETN
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
26
51, 54, 55, 56
Chip select enable. Active low.
Reset SPI interface
Rev 1C
©2009-2013 Exar Corporation 6/31
Rev 1C
Data Sheet
Pin Assignments - TQFP
Pin No.
Pin Name
Description
1, 7, 14, 47, 54, 60, 63, 70
AVDD
Analog power supply, 1.8V
4, 8, 11, 50, 53, 57, 68, 73, 74,
79, 80
AVSS
Analog ground
2
IP1
Positive differential input signal, channel 1
3
IN1
Negative differential input signal, channel 1
5
IP2
Positive differential input signal, channel 2
6
IN2
Negative differential input signal, channel 2
9
IP3
Positive differential input signal, channel 3
10
IN3
Negative differential input signal, channel 3
12
IP4
Positive differential input signal, channel 4
13
IN4
Negative differential input signal, channel 4
48
IP5
Positive differential input signal, channel 5
49
IN5
Negative differential input signal, channel 5
51
IP6
Positive differential input signal, channel 6
52
IN6
Negative differential input signal, channel 6
55
IP7
Positive differential input signal, channel 7
56
IN7
Negative differential input signal, channel 7
58
IP8
Positive differential input signal, channel 8
59
IN8
Negative differential input signal, channel 8
TQFP
DVSS
Digital ground
25, 35
DVDD
Digital and I/O power supply, 1.8V
16
PD
Power-down input. Activate after applying power in order to initialize the
ADC correctly. Alternatively use the SPI power down feature.
LCKP
LVDS bit clock, positive output
20
LCKN
LVDS bit clock, negative output
21
D1P
LVDS channel 1, positive output
22
D1N
LVDS channel 1, negative output
23
D2P
LVDS channel 2, positive output
24
D2N
LVDS channel 2, negative output
27
D3P
LVDS channel 3, positive output
28
D3N
LVDS channel 3, negative output
29
D4P
LVDS channel 4, positive output
30
D4N
LVDS channel 4, negative output
31
D5P
LVDS channel 5, positive output
32
D5N
LVDS channel 5, negative output
33
D6P
LVDS channel 6, positive output
34
D6N
LVDS channel 6, negative output
37
D7P
LVDS channel 7, positive output
38
D7N
LVDS channel 7, negative output
39
D8P
LVDS channel 8, positive output
40
D8N
LVDS channel 8, negative output
©2009-2013 Exar Corporation 7/31
Rev 1C
19
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
15, 17, 18, 26, 36, 43, 44, 46
Rev 1C
Data Sheet
Pin Assignments - TQFP (Continued)
Pin No.
Pin Name
Description
41
FCLKP
LVDS frame clock (1x), positive output
42
FCLKN
LVDS frame clock (1x), negative output
45
RESETN
61
TP
Test pin. Leave open (un-connected) or connect to GND.
62, 64, 66, 67, 69
NC
Not connected
65
VCM
Common mode output pin, 0.5 AVDD
71
CLKP
Positive differential input clock
72
CLKN
Negative differential input clock.
75
OVDD
Digital CMOS inputs supply voltage (1.7V to 3.6V)
76
CSN
77
SDATA
Serial data input
78
SCLK
Serial clock input
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Reset SPI interface
Chip select enable. Active low.
Rev 1C
©2009-2013 Exar Corporation 8/31
Rev 1C
Data Sheet
Absolute Maximum Ratings
The safety of the device is not guaranteed when it is operated above the “Absolute Maximum Ratings”. The device
should not be operated at these “absolute” limits. Adhere to the “Recommended Operating Conditions” for proper device
function. The information contained in the Electrical Characteristics tables and Typical Performance plots reflect the
operating conditions noted on the tables and plots.
Reference Pin
Min
Max
Unit
AVDD
DVDD
OVDD
AVSS, DVSS
Analog inputs and outpts (IPx, INx)
CLKx
LVDS outputs
Digital inputs
AVSS
DVSS
AVSS
DVSS / AVSS
AVSS
AVSS
DVSS
DVSS
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
+2.3
+2.3
+3.9
+0.3
+2.3
+3.9
+2.3
+3.9
V
V
V
V
V
V
V
V
Max
Unit
TBD
+150
°C
°C
Max
Unit
+85
°C
Reliability Information
Parameter
Min
Junction Temperature
Storage Temperature Range
Lead Temperature (Soldering, 10s)
Typ
-60
J-STD-020
ESD Protection
Product
QFN-64
Human Body Model (HBM)
Charged Device Model (CDM)
2kV
500V
Recommended Operating Conditions
Parameter
Min
Operating Temperature Range
-40
Typ
This device can be damaged by ESD. Even though this product is protected with state-of-the-art ESD protection
circuitry, damage may occur if the device is not handled with appropriate precautions. ESD damage may range
from device failure to performance degradation. Analog circuitry may be more susceptible to damage as vary small
parametric changes can result in specification noncompliance.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Parameter
Rev 1C
©2009-2013 Exar Corporation 9/31
Rev 1C
Data Sheet
Electrical Characteristics
(AVDD = 1.8V, DVDD = 1.8V, OVDD = 1.8V, 50MSPS clock, 50% clock duty cycle, -1dBFS 8MHz input signal, 14-bit output, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
±6
%FS
DC Accuracy
No Missing Codes
Offset error after digital offset cancellation
1
Gain Error
LSB
Gain Matching
Gain matching between channels. ±3sigma
value at worst case conditions.
±0.5
%FS
DNL
Differential Non-Linearity
12-bit level
±0.2
LSB
INL
Integral Non-Linearity
12-bit level
±0.6
LSB
VCMO
Common Mode Voltage Output
VAVDD/2
V
Analog Input
VCMI
VFSR
Input Common Mode
Analog input common mode voltage
Full Scale Range
Differential input voltage range
Input Capacitance
Differential input capacitance
Bandwidth
Input bandwidth
VCM -0.1
VCM +0.2
2.0
V
Vpp
2
pF
500
MHz
Power Supply
AVDD
DVDD
OVDD
Analog Supply Voltage
1.7
1.8
2.0
V
Digital Supply Voltage (up to 65MSPS)
Digital and output driver supply voltage
1.7
1.8
2.0
V
Digital Supply Voltage (above 65MSPS)
Digital and output driver supply voltage
1.8
1.9
2.0
V
1.7
1.8
3.6
V
Digital CMOS Input Supply Voltage
Electrical Characteristics - CDK8307A
(AVDD = 1.8V, DVDD = 1.8V, OVDD = 1.8V, 20MSPS clock, 50% clock duty cycle, -1dBFS 8MHz input signal, 14-bit output, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
FIN = 8MHz
70
72.2
dBFS
71.5
dBFS
71.5
dBFS
70.7
dBFS
82
dBc
77
dBc
95
dBc
95
dBc
82
dBc
FIN = 30MHz
77
dBc
FIN = 8MHz
11.6
bits
FIN = 30MHz
11.5
bits
95
dBc
47
mA
Performance
SNR
SINAD
SFDR
HD2
HD3
ENOB
Signal to Noise Ratio
Signal to Noise and Distortion Ratio
Spurious Free Dynamic Range
Second order Harmonic Distortion
Third order Harmonic Distortion
Effective number of Bits
Crosstalk
FIN = 30MHz
FIN = 8MHz
69
FIN = 30MHz
FIN = 8MHz
75
FIN = 30MHz
FIN = 8MHz
85
FIN = 30MHz
FIN = 8MHz
75
See note (1) on page 13
Power Supply
Analog supply current
Digital and output driver supply
mA
Analog power Dissipation
84
mW
Digital power Dissipation
97
mW
Total power Dissipation
180
mW
Power Down Dissipation
Power down mode
10
µW
Sleep Mode Dissipation
Deep sleep mode
30
mW
©2009-2013 Exar Corporation 10/31
Rev 1C
Rev 1C
54
Digital supply current
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Offset Error
Guaranteed
Data Sheet
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Sleep Channel Mode Dissipation
All channels. in sleep ch. mode (light sleep)
46
mW
Sleep Channel Mode Savings
Power dissipation savings per channel off
17
mW
Clock Inputs
20
Maximum Conversion Rate
MSPS
MSPS
Electrical Characteristics - CDK8307B
(AVDD = 1.8V, DVDD = 1.8V, OVDD = 1.8V, 40MSPS clock, 50% clock duty cycle, -1dBFS 8MHz input signal, 14-bit output, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
FIN = 8MHz
70
72.2
dBFS
71.5
dBFS
71.5
dBFS
70.7
dBFS
82
dBc
77
dBc
95
dBc
95
dBc
Performance
SNR
Signal to Noise Ratio
SINAD
Signal to Noise and Distortion Ratio
SFDR
Spurious Free Dynamic Range
HD2
Second order Harmonic Distortion
HD3
Third order Harmonic Distortion
ENOB
FIN = 30MHz
FIN = 8MHz
69
FIN = 30MHz
FIN = 8MHz
75
FIN = 30MHz
FIN = 8MHz
85
FIN = 30MHz
82
dBc
FIN = 30MHz
77
dBc
FIN = 8MHz
11.6
bits
FIN = 30MHz
11.5
bits
95
dBc
90
mA
67
mA
Analog power Dissipation
162
mW
Digital power Dissipation
120
mW
Total power Dissipation
280
mW
Effective number of Bits
Crosstalk
FIN = 8MHz
75
See note (1) on page 13
Power Supply
Analog supply current
Digital supply current
Digital and output driver supply
Power Down Dissipation
Power down mode
10
µW
Sleep Mode Dissipation
Deep sleep mode
41
mW
Sleep Channel Mode Dissipation
All channels. in sleep ch. mode (light sleep)
71
mW
Sleep Channel Mode Savings
Power dissipation savings per channel off
26
mW
Clock Inputs
40
Maximum Conversion Rate
MSPS
20
Minimum Conversion Rate
MSPS
Electrical Characteristics - CDK8307C
(AVDD = 1.8V, DVDD = 1.8V, OVDD = 1.8V, 50MSPS clock, 50% clock duty cycle, -1dBFS 8MHz input signal, 14-bit output, unless otherwise noted)
Symbol
Parameter
Min
Typ
Max
Units
FIN = 8MHz
70
72.2
dBFS
71.5
dBFS
71.5
dBFS
70.7
dBFS
Performance
SNR
SINAD
Signal to Noise Ratio
Signal to Noise and Distortion Ratio
FIN = 30MHz
FIN = 8MHz
69
FIN = 30MHz
©2009-2013 Exar Corporation 11/31
Rev 1C
Rev 1C
Conditions
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
15
Minimum Conversion Rate
Data Sheet
Symbol
Parameter
SFDR
Spurious Free Dynamic Range
HD2
Second order Harmonic Distortion
ENOB
Third order Harmonic Distortion
Effective number of Bits
Crosstalk
Min
Typ
FIN = 8MHz
75
82
dBc
77
dBc
95
dBc
95
dBc
82
dBc
FIN = 30MHz
77
dBc
FIN = 8MHz
11.6
bits
FIN = 30MHz
11.5
bits
95
dBc
111
mA
FIN = 30MHz
FIN = 8MHz
85
FIN = 30MHz
FIN = 8MHz
75
See note (1) on page 13
Max
Units
Power Supply
Analog supply current
73
mA
Analog power Dissipation
200
mW
Digital power Dissipation
132
mW
Total power Dissipation
331
mW
Digital supply current
Digital and output driver supply
Power Down Dissipation
Power down mode
10
µW
Sleep Mode Dissipation
Deep sleep mode
46
mW
Sleep Channel Mode Dissipation
All channels. in sleep ch. mode (light sleep)
83
mW
Sleep Channel Mode Savings
Power dissipation savings per channel off
31
mW
Clock Inputs
50
Maximum Conversion Rate
MSPS
20
Minimum Conversion Rate
MSPS
Electrical Characteristics - CDK8307D
(AVDD = 1.8V, DVDD = 1.8V, OVDD = 1.8V, 65MSPS clock, 50% clock duty cycle, -1dBFS 8MHz input signal, 14-bit output, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
FIN = 8MHz
70
72.2
dBFS
71.5
dBFS
71.5
dBFS
70.7
dBFS
82
dBc
77
dBc
95
dBc
95
dBc
82
dBc
FIN = 30MHz
77
dBc
FIN = 8MHz
11.6
bits
FIN = 30MHz
11.5
bits
95
dBc
143
mA
Performance
SNR
Signal to Noise Ratio
SINAD
Signal to Noise and Distortion Ratio
SFDR
Spurious Free Dynamic Range
HD2
Second order Harmonic Distortion
HD3
Third order Harmonic Distortion
ENOB
Effective number of Bits
Crosstalk
FIN = 30MHz
FIN = 8MHz
69
FIN = 30MHz
FIN = 8MHz
75
FIN = 30MHz
FIN = 8MHz
85
FIN = 30MHz
FIN = 8MHz
75
See note (1) on page 13
Power Supply
Analog supply current
Digital and output driver supply
mA
257
mW
Digital power Dissipation
149
mW
405
mW
Total power Dissipation
Power Down Dissipation
Power down mode
10
µW
Sleep Mode Dissipation
Deep sleep mode
54
mW
Sleep Channel Mode Dissipation
All channels. in sleep ch. mode (light sleep)
103
mW
©2009-2013 Exar Corporation 12/31
Rev 1C
Rev 1C
83
Analog power Dissipation
Digital supply current
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
HD3
Conditions
Data Sheet
Symbol
Parameter
Sleep Channel Mode Savings
Conditions
Min
Power dissipation savings per channel off
Typ
Max
38
Units
mW
Clock Inputs
65
Maximum Conversion Rate
MSPS
20
Minimum Conversion Rate
MSPS
(AVDD = 1.8V, DVDD = 1.8V, OVDD = 1.8V, 80MSPS clock, 50% clock duty cycle, -1dBFS 8MHz input signal, 12-bit output, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Max
Units
FIN = 8MHz
68.5
70.1
dBFS
70
dBFS
68
69.6
dBFS
69.5
dBFS
77
dBc
76
dBc
90
dBc
90
dBc
77
dBc
FIN = 30MHz
76
dBc
FIN = 8MHz
11.3
bits
FIN = 30MHz
11.3
bits
95
dBc
173
mA
Performance
SNR
Signal to Noise Ratio
SINAD
Signal to Noise and Distortion Ratio
SFDR
Spurious Free Dynamic Range
HD2
Second order Harmonic Distortion
HD3
Third order Harmonic Distortion
ENOB
Effective number of Bits
Crosstalk
FIN = 30MHz
FIN = 8MHz
FIN = 30MHz
FIN = 8MHz
74
FIN = 30MHz
FIN = 8MHz
85
FIN = 30MHz
FIN = 8MHz
75
See note (1) on page 13
Power Supply
Analog supply current
88
mA
Analog power Dissipation
312
mW
Digital power Dissipation
158
mW
Total power Dissipation
470
mW
Digital supply current
Digital and output driver supply
Power Down Dissipation
Power down mode
10
µW
Sleep Mode Dissipation
Deep sleep mode
56
mW
Sleep Channel Mode Dissipation
All channels. in sleep ch. mode (light sleep)
116
mW
Sleep Channel Mode Savings
Power dissipation savings per channel off
44
mW
Clock Inputs
80
Maximum Conversion Rate
MSPS
40
MSPS
Max
Units
80
%high
Minimum Conversion Rate
Digital and Timing Electrical Characteristics
(AVDD = 1.8V, DVDD = 1.8V, OVDD = 1.8V, unless otherwise noted)
Symbol
Parameter
Conditions
Min
Typ
Clock Inputs
Duty Cycle
20
Compliance
CMOS, LVDS, LVPECL
Differential input swing
±200
Input range, sine
Differential input swing, sine wave clock input
±800
Input range, CMOS
CLKN connected to ground
Input common mode voltage
Keep voltages within gnd and voltage of OVDD
Input capacitance
Differential
©2009-2013 Exar Corporation mVpp
mVpp
VOVDD
0.3
VOVDD -0.3
2
13/31
mVpp
V
pF
Rev 1C
Rev 1C
Input range, differential
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Electrical Characteristics - CDK8307E
Data Sheet
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Logic Inputs (CMOS)
High Level Input Voltage
VIL
Low Level Input Voltage
IIH
High Level Input Leakage Current
IIL
Low Level Input Leakage Current
CI
Input Capacitance
VOVDD ≥ 3.0V
VOVDD = 1.7V – 3.0V
2
V
0.8 • VOVDD
V
VOVDD ≥ 3.0V
0
0.8
VOVDD = 1.7V – 3.0V
0
0.2 • VOVDD
V
±10
µA
±10
µA
3
V
pF
Data Outputs (LVDS)
Compliance
LVDS
VOUT
Differential Output Voltage
350
mV
VCM
Output Common Mode Voltage
1.2
V
Output Coding
Default/Optional
Offset Binary/2‘s Complement
Timing Characteristics
TAP
Aperture Delay
0.8
ns
εRMS
Aperture Jitter
<0.5
ps
TPD
Start up Time from Power Down
Start up time from Power Down to Active
Mode. References have reached 99% of final
value. (See section Clock Frequency)
260
992
clock
cycles
15
Start up time from Sleep Mode to Active Mode
µs
TSLP
Startup Time from Sleep
0.5
µs
TOVR
Out Of Range Recovery Time
1
clk cycles
TLAT
Pipeline Delay
14
clk cycles
LVDS Output Timing Characterisctics
tdata
tPROP
LCLK to Data Delay Time
Excluding programmable phase shift
250
7
Clock Propogation Delay
LVDS Bit-Clock Duty-Cycle
• TLVDS
+2.6
7
• TLVDS
+3.5
45
Frame clock cycle-to-cycle jitter
ps
7
• TLVDS
ns
+4.2
55
% LCLK
cycle
2.5
% LCLK
cycle
TEDGE
Data Rise- and Fall Time
Calculated from 20% to 80%
0.4
ns
TCLKEDGE
Clock Rise- and Fall Time
Calculated from 20% to 80%
0.4
ns
Note:
(1) Signal applied to 7 channels (FIN0). Measurement taken on one channel with full scale at FIN1. FIN1 = 8MHz, FIN0 = 9.9MHz
(2) The outputs will be functional with higher loads. However, it is recommended to keep the load on output data bits as low as possible to keep dynamic currents
and resulting switching noise at a minimum.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
VIH
Rev 1C
©2009-2013 Exar Corporation 14/31
Rev 1C
Data Sheet
LVDS Timing Diagrams
Analog Input
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
ADC Clock
TLVDS
LCLKP
LCLKN
FCLKN
FCLKP
Dxx<1:0>
D10
N-2
D11
N-2
D0
N-1
D1
N-1
D2
N-1
D3
N-1
D4
N-1
D5
N-1
D6
N-1
D7
N-1
D8
N-1
D9
N-1
D10
N-1
D11
N-1
D0
N
D1
N
D2
N
D3
N
D4
N
D5
N
D4
N
D5
N
D6
N
D6
N
D7
N
D8
N
D9
N
D10
N
TPROP
Figure 1. 12-bit Output, DDR Mode
Analog Input
ADC Clock
TLVDS
LCLKP
LCLKN
FCLKN
FCLKP
Dxx<1:0>
D0
N-1
D1
N-1
D2
N-1
D3
N-1
D4
N-1
D5
N-1
D6
N-1
D7
N-1
D8
N-1
D9 D10 D11 D12 D13
N-1 N-1 N-1 N-1 N-1
D0
N
D1
N
D2
N
D3
N
D7
N
D8
N
D9
N
D10 D11 D12 D13
N
N
N
N
TPROP
Figure 2. 14-bit Output, DDR Mode
Analog Input
ADC Clock
TLVDS
LCLKP
LCLKN
FCLKN
FCLKP
Dxx<1:0>
D10 D11 D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11
N-2 N-2 N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1
D0
N
D1
N
D2
N
D3
N
D4
N
D5
N
D6
N
D7
N
D8
N
D9
N
D10
N
TPROP
Figure 3. 12-bit Output, SDR Mode
TLVDS
LCLKP
LCLKN
Rev 1C
Dxx<1:0>
TLVDS/2
tdata
Figure 4. Data Timing
©2009-2013 Exar Corporation 15/31
Rev 1C
Data Sheet
Serial Interface
The CDK8307 configuration registers can be accessed through a serial interface formed by the pins SDATA (serial
interface data), SCLK (serial interface clock) and CSN (chip select, active low). The following occurs when CSN is set low:
Serial data are shifted into the chip
n
At every rising edge of SCLK, the value present at SDATA is latched
n
SDATA is loaded into the register every 24th rising edge of SCLK
Multiples of 24-bit words data can be loaded within a single active CSN pulse. If more than 24 bits are loaded into
SDATA during one active CSN pulse, only the first 24 bits are kept. The excess bits are ignored. Every 24-bit word is
divided into two parts:
n
The first eight bits form the register address
n
The remaining 16 bits form the register data
Acceptable SCLK frequencies are from 20MHz down to a few hertz. Duty-cycle does not have to be tightly controlled.
Timing Diagram
Figure 5 shows the timing of the serial port interface. Table 1 explains the timing variables used in the Timing Diagram.
tcs
tlo
CSN
SCLK
SDATA
A7
A6
thi
A5
A4
A3
A2
tclk
A1
A0
D15 D14 D13
ts
th
D12
D11 D10
tch
chi
i
tch
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
Figure 5. Serial Port Interface Timing Diagram
Table 1. Serial Port Interface Timing Definitions
Parameter
Minimum Value
Unit
tcs
Setup time between CSN and SCLK
Description
8
ns
tch
Hold time between CSN and SCLK
8
ns
thi
SCLK high time
20
ns
tlo
SCLK low time
20
ns
tclk
SCLK period
50
ns
ts
Data setup time
5
ns
th
Data hold time
5
ns
Register Initialization
Before CDK8307 can be used, the internal registers must be initialized to their default values and power down must be
activated. This can be done immediately after applying supply voltage to the circuit. Register initialization can be done
in one of two ways:
1. By applying a low-going pulse (minimum 20ns) on the RESETN pin (asynchronous).
Power down initialization can be done in one of two ways:
1. By applying a high-going pulse (minimum 20ns) on the PD pin (asynchronous).
2. By cycling the SPI register 0Fhex PD bit to high (reg value '0200'hex) and then low (reg value '0000'hex).
©2009-2013 Exar Corporation 16/31
Rev 1C
Rev 1C
2. By using the serial interface to set the RST bit high. Internal registers are reset to default values when this bit is set.
The RST bit is self-reset to zero. When using this method, do not apply any low-going pulse on the RESETN pin.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
n
Data Sheet
Serial Register Map
Table 2. Summary of Functions Supported by the Serial Interface
Name
Description
Default
D
1
5
D
1
4
Software reset.
This bit is self-clearing
Inactive
pd_ch<8:1>
Channel-specific power-down
Inactive
sleep
Go to sleep-mode
Inactive
pd
Go to power-down
Inactive
pd_pin_cfg<1:0>
Configures the PD pin for
sleep-modes
PD pin
configured for
power-down
mode
ilvds_lclk<2:0>
LVDS current drive programmability for LCLKP and LCLKN pins
3.5mA drive
ilvds_
frame<2:0>
LVDS current drive programmability for FCLKP and FCLKN pins
3.5mA drive
ilvds_dat<2:0>
LVDS current drive programmability for output data pins
3.5mA drive
en_lvds_term
Enables internal termination
for LVDS buffers
Termination
disabled
X
term_lclk<2:0>
Programmable termination
for LCLKN and LCLKP buffers
Termination
disabled
1
term_
frame<2:0>
Programmable termination
for FCLKN and FCLKP buffers
Termination
disabled
1
term_dat<2:0>
Programmable termination
for output data buffers
Termination
disabled
1
invert_ch<8:1>
Swaps the polarity of the
analog input pins electrically
IPx is
positive input
en_ramp
Enables a repeating full-scale
ramp pattern on the outputs
dual_custom_pat
Enable the mode wherein the
output toggles between two
defined codes
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
X
D
6
X
D
5
X
D
4
X
D
3
X
D
2
X
D
1
X
D
0
Address
In Hex
X
00
X
X
X
X
0F
X
X
X
X
X
X
X
X
11
X
X
X
X
X
12
X
X
X
X
X
X
Inactive
X
0
0
Inactive
0
X
0
single_custom_
pat
Enables the mode wherein the
Inactive
output is a constant specified code
0
0
X
bits_custom1<13:0>
Bits for the single custom pattern
and for the first code of the dual Inactive
custom pattern. <0> is the LSB
X
X
X
X
X
X
X
X
X
X
X
X
X
X
26
bits_custom2<13:0>
Bits for the second code of the
dual custom pattern
X
X
X
X
X
X
X
X
X
X
X
X
X
X
27
gain_ch1<3:0>
Programmable gain for channel 1 0dB gain
X
X
gain_ch2<3:0>
Programmable gain for channel 2 0dB gain
gain_ch3<3:0>
Programmable gain for channel 3 0dB gain
gain_ch4<3:0>
Programmable gain for channel 4 0dB gain
X
X
X
X
gain_ch5<3:0>
Programmable gain for channel 5 0dB gain
X
X
X
X
Inactive
Programmable gain for channel 6 0dB gain
Programmable gain for channel 7 0dB gain
gain_ch8<3:0>
Programmable gain for channel 8 0dB gain
©2009-2013 Exar Corporation X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
24
25
X
X
2A
2B
X
17/31
X
Rev 1C
gain_ch6<3:0>
gain_ch7<3:0>
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
rst
D
1
3
X
X
X
Rev 1C
Data Sheet
Table 2. Summary of Functions Supported by the Serial Interface (Continued)
Name
Description
Default
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
X
X
D
4
D
3
D
2
D
1
D
0
phase_ddr<1:0>
Controls the phase of LCLK
output relative to data
90 degrees
pat_deskew
Enable deskew pattern mode
Inactive
0
X
pat_sync
Enable sync pattern mode
Inactive
X
0
btc_mode
Binary two's complement
format for ADC output data
Straight
offset binary
msb_first
Serialized ADC output data
comes out with MSB first
LSB-first
output
en_sdr
Enable SDR output mode. LCLK
becomes a 12x input clock
DDR
output mode
fall_sdr
Rising edge
Controls whether the LCLK risof LCLK
ing or falling edge comes in the
comes in the
middle of the data window when
middle of the
operating in SDR mode
data window
42
45
X
X
X
X
46
1
Nominal
X
ext_vcm_bc<1:0> VCM buffer driving strength control Nominal
X
X
X
X
lvds_pd_mode
Controls LVDS power down mode High z mode
lvds_num_bits
Sets the number of LVDS
output bits
12-bit
lvds_advance
Advance LVDS data bits and
frame clock by one clock cycle
Inactive
0
X
lvds_delay
Delay LVDS data bits and frame
clock by one clock cycle
Inactive
X
0
fs_cntrl<5:0>
Fine adjust ADC full scale range
0% change
X
X
clk_freq<1:0>
Input clock frequency
65MHz
X
50
52
X
53
X
X
X
X
55
X
X
56
D
1
D
0
Address
In Hex
X
00
Address
In Hex
Description of Serial Registers
Table 3. Software Reset
Name
rst
Description
Self-clearing software reset
Default
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
Inactive
Setting the rst register bit to '1', resets all internal registers including the rst register bit itself.
Table 4. Power-Down Modes
Name
Description
Default
pd_ch<8:1>
Channel-specific power-down
Inactive
sleep
Go to sleep-mode
Inactive
pd
Go to power-down
Inactive
pd_pin_cfg<1:0>
Configures the PD pin for
sleep-mode
PD pin configured for powerdown mode
lvds_pd_mode
Controls LVDS power down mode High z mode
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
X
X
X
X
X
X
X
X
X
X
18/31
X
0F
X
Rev 1C
©2009-2013 Exar Corporation D
1
5
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
perfm_cntrl<2:0> ADC performance control
Address
In Hex
X
52
Rev 1C
Data Sheet
Setting pd_ch<n> = '1', powers down channel <n> of the ADC. Setting sleep = '1', powers down the entire chip, except
the band-gap reference circuit.
Setting pd = '1' completely powers down the chip, including the band-gap reference circuit. Start-up time from this mode
is significantly longer than from the sleep and pd_ch<n> modes.
The lvds_pd_mode register configures whether the LVDS data output drivers are powered down or not in sleep and
sleep channel modes. LCLK and FCLK drivers are not affected by this register, and are always on in sleep and sleep
channel modes. If lvds_pd_mode is set low (default), the LVDS output is put in high Z, and the driver is completely
powered down. If lvds_pd_mode is set high, the LVDS output is set to constant 0, and the driver is still on during sleep
and sleep channel modes.
Table 5. LVDS Drive Strength Programmability
Name
Description
Default
ilvds_lclk<2:0>
LVDS current drive programmability for LCLKP and LCLKN pins.
3.5mA drive
ilvds_
frame<2:0>
LVDS current drive programmability for FCLKP and FCLKN pins.
3.5mA drive
ilvds_dat<2:0>
LVDS current drive programmability for output data pins.
3.5mA drive
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
X
X
X
D
5
X
D
4
X
D
3
D
2
D
1
D
0
X
X
X
Address
In Hex
11
X
The current delivered by the LVDS output drivers can be configured as shown in Table 6. The default current is 3.5mA,
which is what the LVDS standard specifies.
Setting the ilvds_lclk<2:0> register controls the current drive strength of the LVDS clock output on the LCLKP and LCLKN
pins.
Setting the ilvds_frame<2:0> register controls the current drive strength of the frame clock output on the FCLKP and
FCLKN pins.
Setting the ilvds_dat<2:0> register controls the current drive strength of the data outputs on the D[8:1]P and D[8:1]
N pins.
Table 6. LVDS Output Drive Strength for LCLK, FCLK, and Data
LVDS Drive Strength
000
3.5 mA (default)
001
2.5 mA
010
1.5 mA
011
0.5 mA
100
7.5 mA
101
6.5 mA
110
5.5 mA
111
4.5 mA
©2009-2013 Exar Corporation 19/31
Rev 1C
ilvds_*<2:0>
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Setting pdn_pin_cfg = '1' configures the circuit to enter sleep mode when the PD pin is set high. When pdn_pin_cfg =
'0', which is the default, the circuit enters power down mode when the PD pin is set high.
Rev 1C
Data Sheet
Table 7. LVDS Internal Termination Programmability
Name
Description
Default
D
1
5
D
1
4
Enables internal termination for
LVDS buffers
Termination
disabled
X
term_lclk<2:0>
Programmable termination for
LCLKN and LCLKP buffers
Termination
disabled
1
term_
frame<2:0>
Programmable termination for
FCLKN and FCLKP buffers
Termination
disabled
1
term_dat<2:0>
Programmable termination for
DxP and DxN buffers
Termination
disabled
1
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
X
X
X
D
5
X
D
4
D
3
D
2
D
1
D
0
X
X
X
Address
In Hex
12
X
X
The off-chip load on the LVDS buffers may represent a characteristic impedance that is not perfectly matched with
the PCB traces. This may result in reflections back to the LVDS outputs and loss of signal integrity. This effect can be
mitigated by enabling an internal termination between the positive and negative outputs of each LVDS buffer. Internal
termination mode can be selected by setting the en_lvds_term bit to '1'. Once this bit is set, the internal termination
values for the bit clock, frame clock, and data buffers can be independently programmed using sets of three bits. Table
8 shows how the internal termination of the LVDS buffers are programmed. The values are typical values and can vary
by up to ±20% from device to device and across temperature.
Table 8. LVDS Output INternal Termination for LCLK, FCLK, and Data
term_*<2:0>
LVDS Internal Termination
000
Termination Disabled
001
280Ω
010
165Ω
011
100Ω
100
125Ω
101
82Ω
110
67Ω
111
56Ω
Table 9. Analog Input Invert
Name
invert_ch<8:1>
Description
Default
Swaps the polarity of the analog
input pins electrically
IPx is positive
input
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
Address
In Hex
X
X
X
X
X
X
X
X
24
The IPx pin represents the positive analog input pin, and INx represents the negative (complementary) input. Setting
the bits marked invert_ch <8:1> (individual control for each channel) causes the inputs to be swapped. INx would then
represent the positive input, and IPx the negative input.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
en_lvds_term
D
1
3
Rev 1C
©2009-2013 Exar Corporation 20/31
Rev 1C
Data Sheet
Table 10. LVDS Test Patterns
Name
Description
Default
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
Address
In Hex
Enables a repeating full-scale
ramp pattern on the outputs
Inactive
X
0
0
dual_custom_pat
Enable the mode wherein the output Inactive
toggles between two defined codes
0
X
0
single_custom_
pat
Enables the mode wherein the
Inactive
output is a constant specified code
0
0
X
bits_custom1<13:0>
Bits for the single custom pattern Inactive
and for the first code of the dual
custom pattern. <0> is the LSB
X
X
X
X
X
X
X
X
X
X
X
X
X
X
26
bits_custom2<13:0>
Bits for the second code of the
dual custom pattern
Inactive
X
X
X
X
X
X
X
X
X
X
X
X
X
X
27
pat_deskew
Enable deskew pattern mode
Inactive
0
X
pat_sync
Enable sync pattern mode
Inactive
X
0
25
45
To ease the LVDS synchronization setup of CDK8307, several test patterns can be set up on the outputs. Normal ADC
data are replaced by the test pattern in these modes. Setting en_ramp to '1' sets up a repeating full-scale ramp pattern
on all data outputs. The ramp starts at code zero and is increased 1LSB every clock cycle. It returns to zero code and
starts the ramp again after reaching the full-scale code.
A constant value can be set up on the outputs by setting single_custom_pat to '1', and programming the desired value
in bits_custom1<13:0>. In this mode, bits_custom1<13:0> replaces the ADC data at the output, and is controlled by
LSB-first and MSB-first modes in the same way as normal ADC data are.
The device may also be made to alternate between two codes by programming dual_custom_pat to '1'. The two codes
are the contents of bits_custom1<13:0> and bits_custom2<13:0>. Two preset patterns can also be selected:
1. Deskew pattern: Set using pat_deskew, this mode replaces the ADC output with '01010101010101' (two LSBs
removed in 12 bit mode).
2. Sync pattern: Set using pat_sync, the normal ADC word is replaced by a fixed 1111110000000 word.
Note: Only one of the above patterns should be selected at the same time.
Table 11. Programmable Gain
Name
Description
Default
D
1
5
D
1
4
D
1
3
D
1
2
gain_ch1<3:0>
Programmable gain for channel 1 0dB gain
gain_ch2<3:0>
Programmable gain for channel 2 0dB gain
gain_ch3<3:0>
Programmable gain for channel 3 0dB gain
gain_ch4<3:0>
Programmable gain for channel 4 0dB gain
X
X
X
X
gain_ch5<3:0>
Programmable gain for channel 5 0dB gain
X
X
X
X
gain_ch6<3:0>
Programmable gain for channel 6 0dB gain
gain_ch7<3:0>
Programmable gain for channel 7 0dB gain
gain_ch8<3:0>
Programmable gain for channel 8 0dB gain
D
1
1
D
1
0
D
9
D
8
X
X
X
X
X
X
X
X
D
7
D
6
D
5
D
4
X
X
X
X
X
X
X
X
D
3
D
2
D
1
D
0
X
X
X
X
Address
In Hex
2A
2B
X
X
X
X
©2009-2013 Exar Corporation 21/31
Rev 1C
Rev 1C
CDK8307 includes a purely digital programmable gain option in addition to the Full-scale Control. The programmable
gain of each channel can be individually set using a set of four bits, indicated as gain_chn<3:0> for Channel x. The gain
setting is coded in binary from 0dB to 12dB, as shown in Table 12 on the following page.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
en_ramp
Data Sheet
Table 12. Gain Setting for Channels 1-8
Channel x Gain Setting
0000
0dB
0001
1dB
0010
2dB
0011
3dB
0100
4dB
0101
5dB
0110
6dB
0111
7dB
1000
8dB
1001
9dB
1010
10dB
1011
11dB
1100
12dB
1101
Do not use
1110
Do not use
1111
Do not use
Table 13. LVDS Clock Programmability and Data Output Modes
Name
Description
Default
phase_ddr<1:0>
Controls the phase of LCLK output relative to data
90 degrees
btc_mode
Binary two's complement format
for ADC output data
Straight offset
binary
msb_first
Serialized ADC output data
comes out with MSB first
LSB-first
output
en_sdr
Enable SDR output mode. LCLK
becomes a 12x input clock
DDR output
mode
fall_sdr
Rising edge
Controls whether the LCLK risof LCLK
ing or falling edge comes in the
comes in the
middle of the data window when
middle of the
operating in SDR mode
data window
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
X
X
D
4
D
3
D
2
D
1
D
0
Address
In Hex
42
X
X
X
X
46
1
The output interface of CDK8307 is normally a DDR interface, with the LCLK rising and falling edge transitions in the
middle of alternate data windows. The phase for LCLK can be programmed relative to the output frame clock and data
using bits phase_ddr<1:0>. The LCLK phase modes are shown in Figure 6. The default timing is identical to setting
phase_ddr<1:0> = '10'.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
gain_chx<3:0>
Rev 1C
©2009-2013 Exar Corporation 22/31
Rev 1C
Data Sheet
PHASE_DDR<1:0>=’00’ = 270°
FCLKN
FCLKP
LCLKP
LCLKN
PHASE_DDR<1:0>=’01’ =180°
FCLKN
FCLKP
LCLKN
LCLKP
Dxx<1:0>
PHASE_DDR<1:0>=’10’ = 90° (Default)
FCLKN
FCLKP
LCLKN
LCLKP
PHASE_DDR<1:0>=’11’ = 0°
FCLKN
FCLKP
LCLKP
LCLKN
Dxx<1:0>
Dxx<1:0>
Figure 6. Phase Programmability Modes for LCLK
The device can also be made to operate in SDR mode by setting the en_sdr bit to '1'. The bit clock (LCLK) is output at
12x times the input clock in this mode, two times the rate in DDR mode. Depending on the state of fall_sdr, LCLK may
be output in either of the two manners shown in Figure 7. As can be seen in Figure 7, only the LCLK rising (or falling)
edge is used to capture the output data in SDR mode. The SDR mode is not recommended beyond 40MSPS because the
LCLK frequency becomes very high.
EN_SDR=’1’, FALL_SDR_’0’
FCLKN
FCLKP
LCLKP
LCLKN
EN_SDR=’1’, FALL_SDR_’1’
FCLKN
FCLKP
LCLKN
LCLKP
Dxx<1:0>
Dxx<1:0>
Figure 7. SDR Interface Modes
The default data output format is offset binary. Two's complement mode can be selected by setting the btc_mode bit to
'1' which inverts the MSB.
The first bit of the frame (following the rising edge of FCLKP) is the LSB of the ADC output for default settings. Programming the msb_first mode results in reverse bit order, and the MSB is output as the first bit following the FCLKP rising edge.
Table 14. Number of Serial Output Bits
Name
Description
Default
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
D
4
lvds_num_bits
Sets the number if LVDS output bits 12-bit
lvds_advance
Advance LVDS data bits and frame
clock by one clock cycle
Inactive
0
X
lvds_delay
Delay LVDS data bits and frame
clock by one clock cycle
Inactive
X
0
D
2
D
1
D
0
Address
In Hex
X
53
Rev 1C
©2009-2013 Exar Corporation D
3
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Dxx<1:0>
23/31
Rev 1C
Data Sheet
The ADC channels have 13 bits of resolution. There are two options for the serial LVDS outputs, 12 bits or 14 bits, selected by setting lvds_num_bits to '0' or '1', respectively. In 12-bit mode, the LSB bit from the ADCs are removed in the
output stream. In 14-bit mode, a '0' is added in the LSB position. Power down mode must be activated after or during
a change in the number of output bits.
TLVDS
LCLKP
LCLKN
TPROP
default:
FCLKP
FCLKN
Dxx<1:0>
D3 D4 D5 D6 D7 D8 D9 D10 D11
N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1
D0
N
TPROP
lvds_delay = ‘1’:
D2 D3 D4 D5 D6 D7 D8 D9 D10 D11
N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1
TPROP
lvds_advance = ‘1’:
D3
N
D4
N
D5
N
D6
N
D7
N
D8
N
D9
N
D0
N
D1
N
D2
N
D3
N
D4
N
D5
N
D6
N
D7
N
D8
N
D3
N
D4
N
D5
N
D6
N
D7
N
D8
N
D9
N
D10
N
TLVDS
FCLKP
FCLKN
Dxx<1:0>
D2
N
TLVDS
FCLKP
FCLKN
Dxx<1:0>
D1
N
D4 D5 D6 D7 D8 D9 D10 D11
N-1 N-1 N-1 N-1 N-1 N-1 N-1 N-1
D0
N
D1
N
D2
N
*LVDS output timing adjustment
Figure 8: LVDS Output Timing Adjustment
Table 15. Full Scale Control
Name
fs_cntrl<5:0>
Description
Fine adjust ADC full scale range
Default
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
0% change
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
Address
In Hex
X
X
X
X
X
X
55
The full-scale voltage range of CDK8307 can be adjusted using an internal 6-bit DAC controlled by the fs_cntrl register.
Changing the value in the register by one step, adjusts the full-scale range approximately 0.3%. This leads to a maximum
range of ±10% adjustment. Table 16 shows how the register settings correspond to the full-scale range. Note that the
values for full-scale range adjustment are approximate. The DAC is, however, guaranteed to be monotonous.
The full-scale control and the programmable gain features differ in two major ways:
2. The programmable gain feature has much coarser gain steps and larger range than the full-scale control.
©2009-2013 Exar Corporation 24/31
Rev 1C
Rev 1C
1. The full-scale control feature controls the full-scale voltage range in an analog fashion, whereas the programmable
gain is a digital feature.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
To ease timing in the receiver when using multiple ADC chips, the CDK8307 has the option to adjust the timing of the
output data and the frame clock. The propagation delay with respect to the ADC input clock can be moved one LVDS
clock cycle forward or backward, by using lvds_advance and lvds_delay, respectively. See figure 8 for details. Note that
LCLK is not affected by lvds_delay or lvds_advance settings.
Data Sheet
Table 16. Register Values with Corresponding Change in Full-Scale Range
fs_cntrl <5:0>
Full-Scale Range Adjustment
111111
+9.7%
...
+0.3%
100000
+0%
011111
-0.3%
...
...
000000
-10%
Table 17. Clock Frequency
Name
clk_freq<1:0>
Description
Input clock frequency
Default
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
D
4
D
3
D
2
50 - 80MHz
D
1
D
0
Address
In Hex
X
X
56
To optimize startup time a register is provided where the input clock frequency can be set. Some internal circuitry has
startup times that are frequency independent. Default counter values are set to accommodate these startup times at
the maximum clock frequency. This will lead to increased startup times at low clock frequency. Setting the value of this
register to the nearest higher clock frequency will reduce the count values of the internal counters, to better fit the actual
startup time, such that the startup time will be reduced. The start up times from Power Down mode and Deep Sleep
mode are changed by this register setting.
Table 18. Clock Frequency Settings
clk_freq <1:0>
Clock Frequency (MHz)
Startup Delay (clock cycles)
Startup Delay (μs)
00
50 - 80
992
12.4 - 19.8
01
32.5 - 50
640
12.8 - 19.7
10
20 - 32.5
420
12.9 - 21
11
15 - 20
260
13 - 17.3
Table 19. Performance Control
Name
Description
Default
perfm_
cntrl<2:0>
ADC performance control
Nominal
ext_vcm_
bc<1:0>
VCM buffer driving strength
control
Nominal
D
1
5
D
1
4
D
1
3
D
1
2
D
1
1
D
1
0
D
9
D
8
D
7
D
6
D
5
X
D
4
X
D
3
D
2
D
1
D
0
X
X
X
Address
In Hex
50
There are two registers that impact performance and power dissipation.
©2009-2013 Exar Corporation 25/31
Rev 1C
Rev 1C
The perfm_cntrl register adjusts the performance level of the ADC core. If full performance is required, the nominal
setting must be used. The lowest code can be used in situations where power dissipation is critical and performance is
less important. For most conditions the performance at the minimum setting will be similar to nominal setting. However,
only 10-bit performance can be expected at worst case conditions. The power dissipation savings shown in Table 20 are
only approximate numbers for the ADC current alone.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
...
100001
Data Sheet
Table 20. Performance Control Settings
Power Dissipation
100
-40% (lower performance)
101
-30%
110
-20%
111
-10%
000 (default)
Nominal
001
Do not use
010
Do not use
011
Do not use
The ext_vcm_bc register controls the driving strength in the buffer supplying the voltage on the VCM pin. If this pin is
not in use, the buffer can be switched off. If current is drawn from the VCM pin, the driving strength can be increased
to keep the voltage on this pin at the correct level.
Table 21. External Common Mode Voltage Buffer Driving Strength
ext_vcm_bc <1:0>
VCM Buffer Driving Strength
00
Off (VCM floating)
01 (default)
Low
10
High
11
Max
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
performance_control <2:0>
Rev 1C
©2009-2013 Exar Corporation 26/31
Rev 1C
Data Sheet
Therory of Operation
The ADC employs a pipelined converter architecture.
Each stage feeds its output data into the digital error
correction logic, ensuring excellent differential linearity
and no missing codes at 13-bit level.
The CDK8307 operates from two sets of supplies and
grounds. The analog supply and ground set is identified
as AVDD and AVSS, while the digital set is identified by
DVDD and DVSS.
Recommended Usage
Analog Input
The analog input to the CDK8307 is a switched capacitor
track-and-hold amplifier optimized for differential operation. Operation at common mode voltages at mid supply
is recommended even if performance will be good for the
ranges specified. The VCM pin provides a voltage suitable
as common mode voltage reference. The internal buffer
for the VCM voltage can be switched off, and driving
capabilities can be changed programming the ext_vcm_
bc<1:0> register.
Figure 9. Input Configuration Diagram
DC-Coupling
Figure 10 shows a recommended configuration for DCcoupling. Note that the common mode input voltage must
be controlled according to specified values. Preferably, the
CM_EXT output should be used as a reference to set the
common mode voltage.
The input amplifier could be inside a companion chip or
it could be a dedicated amplifier. Several suitable single
ended to differential driver amplifiers exist in the market.
The system designer should make sure the specifications
of the selected amplifier is adequate for the total system,
and that driving capabilities comply with the CDK8307
input specifications.
Detailed configuration and usage instructions must be
found in the documentation of the selected driver, and
the values given in Figure 10 must be varied according to
the recommendations for the driver.
43Ω
33pF
Figure 9 shows a simplified drawing of the input network.
The signal source must have sufficiently low output
impedance to charge the sampling capacitors within one
clock cycle. A small external resistor (e.g. 22Ω) in series
with each input is recommended as it helps reducing
transient currents and dampens ringing behavior. A small
Rev 1C
©2009-2013 Exar Corporation 43Ω
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
The CDK8307 is an 8-channel, high-speed, CMOS ADC.
The 13-bits given out by each channel are serialized to
12, 13 or 14-bits and sent out on a single pair of pins in
LVDS format. All eight channels of the CDK8307 operate
from a single differential or single ended clock. The sampling clocks for each of the eight channels are generated
from the clock input using a carefully matched clock buffer tree. The 12x/13x/14x clock required for the serializer
is generated internally from FCLK using a phase-locked
loop (PLL). A 6x/6.5x/7x and 1x clock are also output in
LVDS format, along with the data to enable easy data
capture. The CDK8307 uses internally generated references
that can be shorted across several devices to improve
gain-matching. The differential reference value is 1V. This
results in a differential input of -1V to correspond to the
zero code of the ADC, and a differential input of +1V to
correspond to the full-scale code (code 8191).
differential shunt capacitor at the chip side of the resistors
may be used to provide dynamic charging currents and
may improve performance. The resistors form a low pass
filter with the capacitor, and values must therefore be
determined by requirements for the application.
Figure 10. DC-Coupled Input
27/31
Rev 1C
Data Sheet
AC-Coupling
33Ω
RT
47Ω
33Ω
Ω
pF
Ω
Figure 12. AC-Coupled Input
Note that startup time from Sleep Mode and Power Down
Mode will be affected by this filter as the time required
to charge the series capacitors is dependent on the filter
cut-off frequency.
If the input signal has a long traveling distance, and the
kick-backs from the ADC not are effectively terminated
at the signal source, the input network of Figure 13 can
be used. The configuration is designed to attenuate the
kickback from the ADC and to provide an input impedance
that looks as resistive as possible for frequencies below
Nyquist.
Figure 11. Transformer Coupled Input
If the input signal is traveling a long physical distance
from the signal source to the transformer (for example a
long cable), kick-backs from the ADC will also travel along
this distance. If these kick-backs are not terminated properly at the source side, they are reflected and will add to
the input signal at the ADC input. This could reduce the
ADC performance. To avoid this effect, the source must
effectively terminate the ADC kick-backs, or the traveling
distance should be very short. If this problem could not be
avoided, the circuit in Figure 10 can be used.
©2009-2013 Exar Corporation optional
RT
68Ω
220Ω
pF
120nH
33Ω
Figure 13: Alternative Input Network
Values of the series inductor will however depend on board
design and conversion rate. In some instances a shunt capacitor in parallel with the termination resistor (e.g. 33pF)
may improve ADC performance further. This capacitor
attenuate the ADC kick-back even more, and minimize
the kicks traveling towards the source. However the
impedance match seen into the transformer becomes worse.
28/31
Rev 1C
Rev 1C
Figure 12 shows AC-coupling using capacitors. Resistors
from the CM_EXT output, RCM, should be used to bias the
differential input signals to the correct voltage. The series
capacitor, CI, form the high-pass pole with these resistors,
and the values must therefore be determined based on
the requirement to the high-pass cut-off frequency.
120nH 33Ω
1:1
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
A signal transformer or series capacitors can be used to
make an AC-coupled input network. Figure 11 shows a
recommended configuration using a transformer. Make
sure that a transformer with sufficient linearity is selected,
and that the bandwidth of the transformer is appropriate.
The bandwidth should exceed the sampling rate of the
ADC with at least a factor of 10. It is also important to
keep phase mismatch between the differential ADC inputs
small for good HD2 performance. This type of transformer
coupled input is the preferred configuration for high
frequency signals as most differential amplifiers do
not have adequate performance at high frequencies. Magnetic coupling between the transformers
and PCB traces may impact channel crosstalk, and
must hence be taken into account during PCB layout.
Data Sheet
Clock Input and Jitter Considerations
The input clock can be supplied in a variety of formats.
The clock pins are AC-coupled internally, and hence a wide
common mode voltage range is accepted. Differential
clock sources as LVDS, LVPECL or differential sine wave
can be connected directly to the input pins. For CMOS
inputs, the CLKN pin should be connected to ground, and
the CMOS clock signal should be connected to CLKP. For
differential sine wave clock input the amplitude must be
at least ±0.8Vpp.
The quality of the input clock is extremely important for
high-speed, high-resolution ADCs. The contribution to
SNR from clock jitter with a full scale signal at a given
frequency is shown in equation below.
SNRjitter = 20 • log (2
•
π • FIN • εt)
where FIN is the signal frequency, and εt is the total rms
jitter measured in seconds. The rms jitter is the total of all
jitter sources including the clock generation circuitry, clock
distribution and internal ADC circuitry.
The jitter performance is improved with reduced rise and
fall times of the input clock. Hence, optimum jitter performance is obtained with LVDS or LVPECL clock with fast
edges. CMOS and sine wave clock inputs will result in
slightly degraded jitter performance.
If the clock is generated by other circuitry, it should be retimed with a low jitter master clock as the last operation
before it is applied to the ADC clock input.
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
Typically high-speed ADCs use both clock edges to generate
internal timing signals. In the CDK8307 only the rising
edge of the clock is used. Hence, input clock duty cycles
between 20% and 80% is acceptable.
For applications where jitter may limit the obtainable performance, it is of utmost importance to limit the clock
jitter. This can be obtained by using precise and stable
clock references (e.g. crystal oscillators with good jitter
specifications) and make sure the clock distribution is well
controlled. It might be advantageous to use analog power
and ground planes to ensure low noise on the supplies
to all circuitry in the clock distribution. It is of utmost importance to avoid crosstalk between the ADC output bits
and the clock and between the analog input signal and
the clock since such crosstalk often results in harmonic
distortion.
Rev 1C
©2009-2013 Exar Corporation 29/31
Rev 1C
Data Sheet
Mechanical Dimensions
QFN-64
aaa C A
A
ccc C
A
A2
A3
D
D1
A1
E
F
G
L
e
θ1
E1
aaa
bbb
ccc
Pin 1 ID
0.05 Dia.
Min
–
0.00
–
0.008
0.197
0.197
0.05
0.0096
0.012
0°
Inches
Millimeters
Typ
Max
Min
Typ
–
0.035
–
–
0.0004
0.002
0.00
0.01
0.026
0.028
–
0.65
0.008 REF
0.2 REF
0.010
0.012
0.2
0.25
0.354 BSC
9.00 BSC
0.354 BSC
8.75 BSC
0.205
0.213
5.0
5.2
0.354 BSC
9.00 BSC
0.344 BSC
8.75 BSC
0.205
0.213
5.0
5.2
–
–
1.3
–
0.0168
0.024
0.24
0.42
0.016
0.020
0.3
0.4
0.020 BSC
0.50 BSC
–
12°
0°
–
Tolerance of Form and Position
0.10
0.004
0.10
0.004
0.05
0.002
Max
0.9
0.05
0.7
0.30
5.4
5.4
–
0.6
0.5
12°
NOTES:
1. All dimensions are in millimeters.
2. Die thickness allowable is 0.305mm maximum (.012 inches maximum)
3. Dimensioning & tolerances conform to ASME y14.5m. -1994.
bbb C B
B
C
bbb C A
1.14
5. The pin #1 identifier must be placed on the top surface of the package by using indentation mark
or other feature of package body.
6. Exact shape and size of this feature is optional.
7. Package warpage max 0.08mm.
SIDE VIEW
9. Applied only to terminals.
10. Package corners unless otherwise specipied are r0.175±0.025mm.
F
D2
0.45
4. Dimension applies to plated terminal and is measured between 0.20 and 0.25mm from terminal tip.
8. Applied for exposed pad and terminals. Exclude embedding part of exposed pad from measuring.
TOP VIEW
Pin 1 ID
Dia. 0.20
seating
plane
θ1
1.14
G
E2
L
e
b
0.10 M C A B
L
BOTTOM VIEW
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
aaa C B
Symbol
A
A1
A2
A3
b
D
D1
D2
E
E1
E2
Rev 1C
©2009-2013 Exar Corporation 30/31
Rev 1C
Data Sheet
Mechanical Dimensions (Continued)
TQFP-80
Dimensions (mm)
1.20
0.10 ±0.05
1.00 ±0.05
A3
0.25
b
0.22 ±0.05
0.145 +0.055
0.145 -0.045
12.00 ±0.20
12.00 ±0.20
c
D
E
e
0.50
HD
HE
L
Lp
L1
x
y
ZD
ZE
14.00 ±0.20
14.00 ±0.20
0.50
0.60 ±0.15
1.00 ±0.20
0.08
0.08
1.25
1.25
3° +5°
3° -3°
θ
CDK8307 12/13-bit, 20/40/50/65/80MSPS, Eight Channel, Ultra Low Power ADC with LVDS
TQFP-80
Symbol
A
A1
A2
NOTE:
Each lead centerline is located within 0.08mm of
its true position at maximum material condition.
Detail of Lead End
For Further Assistance:
Rev 1C
Exar Corporation Headquarters and Sales Offices
48720 Kato Road
Tel.: +1 (510) 668-7000
Fremont, CA 94538 - USA
Fax: +1 (510) 668-7001
www.exar.com
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any
circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration
purposes and may vary depending upon a user’s specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or
to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage
has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances.
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
©2009-2013 Exar Corporation 31/31
Rev 1C
Similar pages