CALOGIC J201 N-channel jfet general purpose amplifier Datasheet

N-Channel JFET
General Purpose Amplifier
CORPORATION
J201 – J204 / SST201 – SST204
FEATURES
ABSOLUTE MAXIMUM RATINGS
(TA = 25oC unless otherwise specified)
• High Input Impedance
• Low IGSS
Gate-Source or Gate-Drain Voltage . . . . . . . . . . . . . . . . -40V
Gate Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Storage Temperature Range . . . . . . . . . . . . . -55oC to +150oC
Operating Temperature Range . . . . . . . . . . . -55oC to +135oC
Lead Temperature (Soldering, 10sec) . . . . . . . . . . . . . +300oC
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360mW
Derate above 25oC . . . . . . . . . . . . . . . . . . . . . . . 3.3mW/ oC
PIN CONFIGURATION
SOT-23
NOTE: Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to the device. These are
stress ratings only and functional operation of the device at these or
any other conditions above those indicated in the operational sections
of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
G
TO-92
D
S
ORDERING INFORMATION
PRODUCT MARKING (SOT-23)
SST201
A01
SST202
A02
SST203
A03
SST204
A04
G
D S
5010
Part
Package
Temperature Range
J201-204
Plastic TO-92
-55oC to +135oC
SST201-204 Plastic SOT-23
-55oC to +135oC
For Sorted Chips in Carriers see 2N4338 series.
ELECTRICAL CHARACTERISTICS (TA = 25oC unless otherwise specified)
SYMBOL
PARAMETER
201
202
203
204
MIN TYP MAX MIN TYP MAX MIN TYP MAX MIN TYP MAX
IGSS
Gate Reverse Current
(Note 1)
VGS(off)
Gate-Source Cutoff
Voltage
-0.3
BVGSS
Gate-Source Breakdown
Voltage
-40
IDSS
Saturation Drain Current
(Note 2)
0.2
IG
Gate Current (Note 1)
gfs
Common-Source Forward
500
Transconductance (Note 2)
gos
Common-Source Output
Conductance
1
3.5
10
2.5
Ciss
Common-Source Input
Capacitance
4
4
4
4
Crss
Common-Source Reverse
Transfer Capacitance
1
1
1
1
en
Equivalent Short-Circuit
Input Noise Voltage
5
5
5
10
-100
-100
-1.5 -0.8
-4.0
-2.0
-100
-100
-10.0 -0.3
-2.0
UNITS
pA
TEST CONDITIONS
VDS = 0, VGS = -20V
VDS = 20V, ID = 10nA
V
-40
1.0
-40
0.9
-10
4.5
4.0
-10
1,000
-25
20
-10
1,500
0.2
VDS = 0, IG = -1µA
1.2
-10
3.0
mA
VDS = 20V, VGS = 0
pA
VDG = 20V, ID = IDSS(min)
500 1,500
µs
VDS = 20V,
VGS = 0
pF
NOTES: 1. Approximately doubles for every 10oC increase in TA.
2. Pulse test duration = 2ms.
3. For design reference only, not 100% tested.
f = 1kHz
nV
√
Hz
f = 1MHz
(Note 3)
VDS = 10V, f = 1kHz
VGS = 0
(Note 3)
Similar pages