TI MSP430G2202IRSA16R Mixed signal microcontroller Datasheet

MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
MIXED SIGNAL MICROCONTROLLER
FEATURES
1
•
•
•
•
•
•
•
•
Low Supply Voltage Range: 1.8 V to 3.6 V
Ultra-Low Power Consumption
– Active Mode: 220 µA at 1 MHz, 2.2 V
– Standby Mode: 0.5 µA
– Off Mode (RAM Retention): 0.1 µA
Five Power-Saving Modes
Ultra-Fast Wake-Up From Standby Mode in
Less Than 1 µs
16-Bit RISC Architecture, 62.5-ns Instruction
Cycle Time
Basic Clock Module Configurations
– Internal Frequencies up to 16 MHz With
Four Calibrated Frequencies
– Internal Very-Low-Power Low-Frequency
(LF) Oscillator
– 32-kHz Crystal
– External Digital Clock Source
One 16-Bit Timer_A With Three
Capture/Compare Registers
Up to 16 Touch-Sense Enabled I/O Pins
•
•
•
•
•
•
•
•
Universal Serial Interface (USI) Supporting SPI
and I2C
10-Bit 200-ksps Analog-to-Digital (A/D)
Converter With Internal Reference,
Sample-and-Hold, and Autoscan
(MSP430G2x32 Only)
Brownout Detector
Serial Onboard Programming,
No External Programming Voltage Needed,
Programmable Code Protection by Security
Fuse
On-Chip Emulation Logic With Spy-Bi-Wire
Interface
Family Members are Summarized in Table 1
Package Options
– TSSOP: 14 Pin, 20 Pin
– PDIP: 20 Pin
– QFN: 16 Pin
For Complete Module Descriptions, See the
MSP430x2xx Family User’s Guide (SLAU144)
DESCRIPTION
The Texas Instruments MSP430™ family of ultra-low-power microcontrollers consist of several devices featuring
different sets of peripherals targeted for various applications. The architecture, combined with five low-power
modes is optimized to achieve extended battery life in portable measurement applications. The device features a
powerful 16-bit RISC CPU, 16-bit registers, and constant generators that contribute to maximum code efficiency.
The digitally controlled oscillator (DCO) allows wake-up from low-power modes to active mode in less than 1 µs.
The MSP430G2x32 and MSP430G2x02 series of microcontrollers are ultra-low-power mixed signal
microcontrollers with built-in 16-bit timers, and up to 16 I/O touch sense enabled pins and built-in communication
capability using the universal serial communication interface. The MSP430G2x32 series have a 10-bit A/D
converter. For configuration details see Table 1. Typical applications include low-cost sensor systems that
capture analog signals, convert them to digital values, and then process the data for display or for transmission
to a host system.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Table 1. Available Options (1)
Device
EEM
Flash
(KB)
RAM
(B)
Timer_A
ADC10
Channel
USI
CLOCK
MSP430G2432IN20
MSP430G2432IPW20
MSP430G2432IRSA16
1
8
256
1x TA3
8
1
LF, DCO, VLO
I/O
Package
Type (2)
16
20-PDIP
16
20-TSSOP
10
16-QFN
MSP430G2432IPW14
10
14-TSSOP
MSP430G2332IN20
16
20-PDIP
MSP430G2332IPW20
16
20-TSSOP
10
16-QFN
MSP430G2332IPW14
10
14-TSSOP
MSP430G2232IN20
16
20-PDIP
MSP430G2232IPW20
16
20-TSSOP
10
16-QFN
MSP430G2232IPW14
10
14-TSSOP
MSP430G2132IN20
16
20-PDIP
MSP430G2132IPW20
16
20-TSSOP
MSP430G2332IRSA16
MSP430G2232IRSA16
MSP430G2132IRSA16
1
1
1
4
2
1
256
256
128
1x TA3
1x TA3
1x TA3
8
8
8
1
1
1
LF, DCO, VLO
LF, DCO, VLO
LF, DCO, VLO
10
16-QFN
MSP430G2132IPW14
10
14-TSSOP
MSP430G2402IN20
16
20-PDIP
16
20-TSSOP
MSP430G2402IPW20
MSP430G2402IRSA16
1
8
256
1x TA3
-
1
LF, DCO, VLO
10
16-QFN
MSP430G2402IPW14
10
14-TSSOP
MSP430G2302IN20
16
20-PDIP
16
20-TSSOP
MSP430G2302IPW20
MSP430G2302IRSA16
1
4
256
1x TA3
-
1
LF, DCO, VLO
10
16-QFN
MSP430G2302IPW14
10
14-TSSOP
MSP430G2202IN20
16
20-PDIP
MSP430G2202IPW20
16
20-TSSOP
10
16-QFN
MSP430G2202IPW14
10
14-TSSOP
MSP430G2102IN20
16
20-PDIP
MSP430G2102IPW20
16
20-TSSOP
10
16-QFN
10
14-TSSOP
MSP430G2202IRSA16
MSP430G2102IRSA16
1
1
MSP430G2102IPW14
(1)
(2)
2
2
1
256
128
1x TA3
1x TA3
-
-
1
1
LF, DCO, VLO
LF, DCO, VLO
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Device Pinout
PW PACKAGE
(TOP VIEW)
DVCC
P1.0/TA0CLK/ACLK/A0
P1.1/TA0.0/A1
P1.2/TA0.1/A2
P1.3/ADC10CLK/A3/VREF-/VEREFP1.4/TA0.2/SMCLK/A4/VREF+/VEREF+/TCK
P1.5/TA0.0/SCLK/A5/TMS
1
2
3
4
5
6
7
14
13
12
11
10
9
8
DVSS
XIN/P2.6/TA0.1
XOUT/P2.7
TEST/SBWTCK
RST/NMI/SBWTDIO
P1.7/SDI/SDA/A7/TDO/TDI
P1.6/TA0.1/SDO/SCL/A6/TDI/TCLK
NOTE: ADC10 pin functions are available only on MSP430G2x32.
NOTE: The pulldown resistors of port pins P2.0, P2.1, P2.2, P2.3, P2.4, and P2.5 should be enabled by setting P2REN.x = 1.
DVCC
AVCC
DVSS
AVSS
RSA PACKAGE
(TOP VIEW)
16 15 14 13
1
12
2
11
3
10
4
9
5 6 7 8
XIN/P2.6/TA0.1
XOUT/P2.7
TEST/SBWTCK
RST/NMI/SBWTDIO
P1.4/SMCLK/A4/VREF+/VEREF+/TCK
P1.5/TA0.0/SCLK/A5/TMS
P1.6/TA0.1/SDO/SCL/A6/TDI/TCLK
P1.7/SDI/SDA/A7/TDO/TDI
P1.0/TA0CLK/ACLK/A0
P1.1/TA0.0/A1
P1.2/TA0.1/A2
P1.3/ADC10CLK/A3/VREF-/VEREF-
NOTE: ADC10 pin functions are available only on MSP430G2x32.
NOTE: The pulldown resistors of port pins P2.0, P2.1, P2.2, P2.3, P2.4, and P2.5 should be enabled by setting P2REN.x = 1.
N OR PW PACKAGE
(TOP VIEW)
DVCC
P1.0/TA0CLK/ACLK/A0
P1.1/TA0.0/A1
P1.2/TA0.1/A2
P1.3/ADC10CLK/VREF-/VEREF-/A3
P1.4/TA0.2/SMCLK/A4/VREF+/VEREF+/TCK
P1.5/TA0.0/A5/TMS
P2.0
P2.1
P2.2
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
DVSS
XIN/P2.6/TA0.1
XOUT/P2.7
TEST/SBWTCK
RST/NMI/SBWTDIO
P1.7/SDI/SDA/A7/TDO/TDI
P1.6/TA0.1/SDO/SCL/A6/TDI/TCLK
P2.5
P2.4
P2.3
NOTE: ADC10 pin functions are available only on MSP430G2x32.
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
3
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Functional Block Diagram, MSP430G2x32
XIN
DVCC
XOUT
DVSS
P1.x
P2.x
up to 8
8
ACLK
Clock
System
Flash
RAM
ADC
8KB
4KB
2KB
1KB
256B
256B
256B
128B
10-Bit
8 Ch.
Autoscan
1 ch DMA
SMCLK
MCLK
16MHz
CPU
MAB
incl. 16
Registers
MDB
Emulation
2BP
Port P1
Port P2
8 I/O
Interrupt
capability
pullup/down
resistors
up to 8 I/O
Interrupt
capability
pullup/down
resistors
USI
Watchdog
WDT+
Brownout
Protection
JTAG
Interface
15-Bit
Timer0_A3
3 CC
Registers
Spy-Bi
Wire
Universal
Serial
Interface
SPI, I2C
RST/NMI
Note: Port P2. Two pins are available on the 14/16-pin package options. Eight pins are available on the 20-pin package options.
Functional Block Diagram, MSP430G2x02
XIN
XOUT
DVCC
DVSS
P1.x
P2.x
up to 8
8
ACLK
Clock
System
Flash
RAM
8KB
4KB
2KB
1KB
256B
256B
256B
128B
SMCLK
MCLK
16MHz
CPU
MAB
incl. 16
Registers
MDB
Emulation
2BP
JTAG
Interface
Port P1
Port P2
8 I/O
Interrupt
capability
pull-up/down
resistors
up to 8 I/O
Interrupt
capability
pull-up/down
resistors
USI
Brownout
Protection
Watchdog
WDT+
15-Bit
Spy-Bi
Wire
Timer0_A3
3 CC
Registers
Universal
Serial
Interface
SPI, I2C
RST/NMI
Note: Port P2. Two pins are available on the 14/16-pin package options. Eight pins are available on the 20-pin package options.
4
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Table 2. Terminal Functions
TERMINAL
NO.
NAME
14
N, PW
16
RSA
I/O
P1.0/
TA0CLK/
ACLK/
DESCRIPTION
20
N, PW
General-purpose digital I/O pin
2
1
2
I/O
Timer0_A, clock signal TACLK input
ACLK signal output
A0
ADC10 analog input A0 (1)
P1.1/
General-purpose digital I/O pin
TA0.0/
3
2
3
I/O
Timer0_A, capture: CCI0A input, compare: Out0 output
ADC10 analog input A1 (1)
A1
P1.2/
TA0.1/
General-purpose digital I/O pin
4
3
4
I/O
Timer0_A, capture: CCI1A input, compare: Out1 output
A2
ADC10 analog input A2 (1)
P1.3/
General-purpose digital I/O pin
ADC10CLK/
A3/
5
4
5
I/O
ADC10, conversion clock output (1)
ADC10 analog input A3 (1)
VREF-/VEREF
ADC10 negative reference voltage (1)
P1.4/
General-purpose digital I/O pin
TA0.2/
Timer0_A, capture: CCI2A input, compare: Out2 output
SMCLK/
A4/
6
5
6
I/O
SMCLK signal output
ADC10 analog input A4 (1)
VREF+/VEREF+/
ADC10 positive reference voltage (1)
TCK
JTAG test clock, input terminal for device programming and test
P1.5/
General-purpose digital I/O pin
TA0.0/
Timer0_A, compare: Out0 output
A5/
7
6
7
I/O
ADC10 analog input A5 (1)
SCLK/
USI: clk input in I2C mode; clk in/output in SPI mode
TMS
JTAG test mode select, input terminal for device programming and test
P1.6/
General-purpose digital I/O pin
TA0.1/
Timer0_A, compare: Out1 output
A6/
ADC10 analog input A6 (1)
SDO/
8
7
14
I/O
USI: Data output in SPI mode
SCL/
USI: I2C clock in I2C mode
TDI/
JTAG test data input or test clock input during programming and test
TCLK
P1.7/
General-purpose digital I/O pin
A7/
ADC10 analog input A7 (1)
SDI/
9
8
15
I/O
SDA/
USI: Data input in SPI mode
USI: I2C data in I2C mode
TDO/TDI (2)
JTAG test data output terminal or test data input during programming and test
P2.0
-
-
8
I/O
General-purpose digital I/O pin
P2.1
-
-
9
I/O
General-purpose digital I/O pin
P2.2
-
-
10
I/O
General-purpose digital I/O pin
P2.3
-
-
11
I/O
General-purpose digital I/O pin
P2.4
-
-
12
I/O
General-purpose digital I/O pin
P2.5
-
-
13
I/O
General-purpose digital I/O pin
(1)
(2)
Available only on MSP430G2x32 devices.
TDO or TDI is selected via JTAG instruction.
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
5
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Table 2. Terminal Functions (continued)
TERMINAL
NO.
NAME
14
N, PW
16
RSA
I/O
DESCRIPTION
20
N, PW
XIN/
Input terminal of crystal oscillator
P2.6/
13
12
19
I/O
TA0.1
General-purpose digital I/O pin
Timer0_A, compare: Out1 output
XOUT/
P2.7
12
11
18
I/O
10
9
16
I
RST/
Output terminal of crystal oscillator (3)
General-purpose digital I/O pin
Reset
NMI/
SBWTDIO/
Nonmaskable interrupt input
Spy-Bi-Wire test data input/output during programming and test
TEST/
11
10
17
I
SBWTCK
Selects test mode for JTAG pins on Port 1. The device protection fuse is
connected to TEST.
Spy-Bi-Wire test clock input during programming and test
DVCC
1
16
1
NA
Supply voltage
AVCC
NA
15
NA
NA
Supply voltage
DVSS
14
14
20
NA
Ground reference
AVSS
NA
13
NA
NA
Ground reference
NC
-
-
-
NA
Not connected
QFN Pad
-
Pad
-
NA
QFN package pad connection to VSS recommended.
(3)
6
If XOUT/P2.7 is used as an input, excess current will flow until P2SEL.7 is cleared. This is due to the oscillator output driver connection
to this pad after reset.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
SHORT-FORM DESCRIPTION
CPU
The MSP430™ CPU has a 16-bit RISC architecture
that is highly transparent to the application. All
operations, other than program-flow instructions, are
performed as register operations in conjunction with
seven addressing modes for source operand and four
addressing modes for destination operand.
Program Counter
PC/R0
Stack Pointer
SP/R1
SR/CG1/R2
Status Register
The CPU is integrated with 16 registers that provide
reduced
instruction
execution
time.
The
register-to-register operation execution time is one
cycle of the CPU clock.
Constant Generator
Four of the registers, R0 to R3, are dedicated as
program counter, stack pointer, status register, and
constant generator, respectively. The remaining
registers are general-purpose registers.
Peripherals are connected to the CPU using data,
address, and control buses, and can be handled with
all instructions.
The instruction set consists of the original 51
instructions with three formats and seven address
modes and additional instructions for the expanded
address range. Each instruction can operate on word
and byte data.
Instruction Set
The instruction set consists of 51 instructions with
three formats and seven address modes. Each
instruction can operate on word and byte data.
Table 3 shows examples of the three types of
instruction formats; Table 4 shows the address
modes.
CG2/R3
General-Purpose Register
R4
General-Purpose Register
R5
General-Purpose Register
R6
General-Purpose Register
R7
General-Purpose Register
R8
General-Purpose Register
R9
General-Purpose Register
R10
General-Purpose Register
R11
General-Purpose Register
R12
General-Purpose Register
R13
General-Purpose Register
R14
General-Purpose Register
R15
Table 3. Instruction Word Formats
EXAMPLE
OPERATION
Dual operands, source-destination
FORMAT
ADD R4,R5
R4 + R5 —> R5
Single operands, destination only
CALL R8
PC —>(TOS), R8—> PC
JNE
Jump-on-equal bit = 0
Relative jump, un/conditional
Table 4. Address Mode Descriptions (1)
S
D
SYNTAX
EXAMPLE
OPERATION
Register
ADDRESS MODE
✓
✓
MOV Rs,Rd
MOV R10,R11
R10 – –> R11
Indexed
✓
✓
MOV X(Rn),Y(Rm)
MOV 2(R5),6(R6)
M(2+R5) – –> M(6+R6)
Symbolic (PC relative)
✓
✓
MOV EDE,TONI
M(EDE) – –> M(TONI)
Absolute
✓
✓
MOV &MEM,&TCDAT
M(MEM) – –> M(TCDAT)
Indirect
✓
MOV @Rn,Y(Rm)
MOV @R10,Tab(R6)
M(R10) – –> M(Tab+R6)
Indirect autoincrement
✓
MOV @Rn+,Rm
MOV @R10+,R11
M(R10) – –> R11
R10 + 2 – –> R10
Immediate
✓
MOV #X,TONI
MOV #45,TONI
#45 – –> M(TONI)
(1)
S = source, D = destination
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
7
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Operating Modes
The MSP430 devices have one active mode and five software selectable low-power modes of operation. An
interrupt event can wake up the device from any of the low-power modes, service the request, and restore back
to the low-power mode on return from the interrupt program.
The following six operating modes can be configured by software:
• Active mode (AM)
– All clocks are active
• Low-power mode 0 (LPM0)
– CPU is disabled
– ACLK and SMCLK remain active, MCLK is disabled
• Low-power mode 1 (LPM1)
– CPU is disabled
– ACLK and SMCLK remain active, MCLK is disabled
– DCO's dc generator is disabled if DCO not used in active mode
• Low-power mode 2 (LPM2)
– CPU is disabled
– MCLK and SMCLK are disabled
– DCO's dc generator remains enabled
– ACLK remains active
• Low-power mode 3 (LPM3)
– CPU is disabled
– MCLK and SMCLK are disabled
– DCO's dc generator is disabled
– ACLK remains active
• Low-power mode 4 (LPM4)
– CPU is disabled
– ACLK is disabled
– MCLK and SMCLK are disabled
– DCO's dc generator is disabled
– Crystal oscillator is stopped
8
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Interrupt Vector Addresses
The interrupt vectors and the power-up starting address are located in the address range 0FFFFh to 0FFC0h.
The vector contains the 16-bit address of the appropriate interrupt handler instruction sequence.
If the reset vector (located at address 0FFFEh) contains 0FFFFh (for example, if flash is not programmed) the
CPU goes into LPM4 immediately after power-up.
Table 5. Interrupt Sources, Flags, and Vectors
INTERRUPT SOURCE
INTERRUPT FLAG
Power-Up
External Reset
Watchdog Timer+
Flash key violation
PC out-of-range (1)
PORIFG
RSTIFG
WDTIFG
KEYV (2)
NMI
Oscillator fault
Flash memory access violation
NMIIFG
OFIFG
ACCVIFG (2) (3)
Watchdog Timer+
WDTIFG
Timer0_A3
Timer0_A3
(2)
(3)
(4)
(5)
(6)
TACCR2 TACCR1 CCIFG.
TAIFGTable 3 (4)
WORD
ADDRESS
PRIORITY
Reset
0FFFEh
31, highest
(non)-maskable
(non)-maskable
(non)-maskable
0FFFCh
30
0FFFAh
29
0FFF8h
28
0FFF6h
27
maskable
0FFF4h
26
maskable
0FFF2h
25
maskable
0FFF0h
24
0FFEEh
23
0FFECh
22
ADC10 (5)
ADC10IFG (4) (5)
maskable
0FFEAh
21
USI
USIIFG, USISTTIFG (2) (4)
maskable
0FFE8h
20
I/O Port P2 (up to eight flags)
P2IFG.0 to P2IFG.7
(2) (4)
maskable
0FFE6h
19
I/O Port P1 (up to eight flags)
P1IFG.0 to P1IFG.7 (2) (4)
maskable
0FFE4h
18
0FFE2h
17
0FFE0h
16
0FFDEh to
0FFC0h
15 to 0, lowest
See
(1)
TACCR0 CCIFG
(4)
SYSTEM
INTERRUPT
(6)
A reset is generated if the CPU tries to fetch instructions from within the module register memory address range (0h to 01FFh) or from
within unused address ranges.
Multiple source flags
(non)-maskable: the individual interrupt-enable bit can disable an interrupt event, but the general interrupt enable cannot.
Interrupt flags are located in the module.
MSP430G2x32 only
The interrupt vectors at addresses 0FFDEh to 0FFC0h are not used in this device and can be used for regular program code if
necessary.
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
9
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Special Function Registers (SFRs)
Most interrupt and module enable bits are collected into the lowest address space. Special function register bits
not allocated to a functional purpose are not physically present in the device. Simple software access is provided
with this arrangement.
Legend
rw:
rw-0,1:
rw-(0,1):
Bit can be read and written.
Bit can be read and written. It is reset or set by PUC.
Bit can be read and written. It is reset or set by POR.
SFR bit is not present in device.
Table 6. Interrupt Enable Register 1 and 2
Address
7
6
00h
WDTIE
OFIE
NMIIE
ACCVIE
Address
5
4
1
0
ACCVIE
NMIIE
3
2
OFIE
WDTIE
rw-0
rw-0
rw-0
rw-0
Watchdog Timer interrupt enable. Inactive if watchdog mode is selected. Active if Watchdog Timer is configured in
interval timer mode.
Oscillator fault interrupt enable
(Non)maskable interrupt enable
Flash access violation interrupt enable
7
6
5
4
3
2
1
0
01h
Table 7. Interrupt Flag Register 1 and 2
Address
7
6
5
02h
WDTIFG
OFIFG
PORIFG
RSTIFG
NMIIFG
Address
4
3
2
1
0
NMIIFG
RSTIFG
PORIFG
OFIFG
WDTIFG
rw-0
rw-(0)
rw-(1)
rw-1
rw-(0)
Set on watchdog timer overflow (in watchdog mode) or security key violation.
Reset on VCC power-on or a reset condition at the RST/NMI pin in reset mode.
Flag set on oscillator fault.
Power-On Reset interrupt flag. Set on VCC power-up.
External reset interrupt flag. Set on a reset condition at RST/NMI pin in reset mode. Reset on VCC power-up.
Set via RST/NMI pin
7
6
5
4
3
2
1
0
03h
10
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Memory Organization
Table 8. Memory Organization
MSP430G2102
MSP430G2132
MSP430G2202
MSP430G2232
MSP430G2302
MSP430G2332
MSP430G2402
MSP430G2432
Size
1kB
2kB
4kB
8kB
Main: interrupt vector
Flash
0xFFFF to 0xFFC0
0xFFFF to 0xFFC0
0xFFFF to 0xFFC0
0xFFFF to 0xFFC0
Main: code memory
Flash
0xFFFF to 0xFC00
0xFFFF to 0xF800
0xFFFF to 0xF000
0xFFFF to 0xE000
Information memory
Size
256 Byte
256 Byte
256 Byte
256 Byte
Flash
010FFh to 01000h
010FFh to 01000h
010FFh to 01000h
010FFh to 01000h
Memory
RAM
Peripherals
Size
128 B
256 B
256 B
256 B
0x027F to 0x0200
0x02FF to 0x0200
0x02FF to 0x0200
0x02FF to 0x0200
16-bit
01FFh to 0100h
01FFh to 0100h
01FFh to 0100h
01FFh to 0100h
8-bit
0FFh to 010h
0FFh to 010h
0FFh to 010h
0FFh to 010h
0Fh to 00h
0Fh to 00h
0Fh to 00h
0Fh to 00h
8-bit SFR
Flash Memory
The flash memory can be programmed via the Spy-Bi-Wire/JTAG port or in-system by the CPU. The CPU can
perform single-byte and single-word writes to the flash memory. Features of the flash memory include:
• Flash memory has n segments of main memory and four segments of information memory (A to D) of
64 bytes each. Each segment in main memory is 512 bytes in size.
• Segments 0 to n may be erased in one step, or each segment may be individually erased.
• Segments A to D can be erased individually or as a group with segments 0 to n. Segments A to D are also
called information memory.
• Segment A contains calibration data. After reset, segment A is protected against programming and erasing. It
can be unlocked, but care should be taken not to erase this segment if the device-specific calibration data is
required.
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
11
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Peripherals
Peripherals are connected to the CPU through data, address, and control buses and can be handled using all
instructions. For complete module descriptions, see the MSP430x2xx Family User's Guide (SLAU144).
Oscillator and System Clock
The clock system is supported by the basic clock module that includes support for a 32768-Hz watch crystal
oscillator, an internal very-low-power low-frequency oscillator and an internal digitally controlled oscillator (DCO).
The basic clock module is designed to meet the requirements of both low system cost and low power
consumption. The internal DCO provides a fast turn-on clock source and stabilizes in less than 1 µs. The basic
clock module provides the following clock signals:
• Auxiliary clock (ACLK), sourced either from a 32768-Hz watch crystal or the internal LF oscillator.
• Main clock (MCLK), the system clock used by the CPU.
• Sub-Main clock (SMCLK), the sub-system clock used by the peripheral modules.
The DCO settings to calibrate the DCO output frequency are stored in the information memory segment A.
Calibration Data Stored in Information Memory Segment A
Calibration data is stored for both the DCO and for ADC10 organized in a tag-length-value structure.
Table 9. Tags Used by the ADC Calibration Tags
NAME
ADDRESS
VALUE
DESCRIPTION
TAG_DCO_30
0x10F6
0x01
DCO frequency calibration at VCC = 3 V and TA = 30°C at calibration
TAG_ADC10_1
0x10DA
0x08
ADC10_1 calibration tag
TAG_EMPTY
-
0xFE
Identifier for empty memory areas
Table 10. Labels Used by the ADC Calibration Tags
LABEL
SIZE
ADDRESS OFFSET
INCHx = 0x1010, REF2_5 = 1, TA = 85°C
word
0x0010
CAL_ADC_25T30
INCHx = 0x1010, REF2_5 = 1, TA = 30°C
word
0x000E
CAL_ADC_25VREF_FACTOR
12
CONDITION AT CALIBRATION / DESCRIPTION
CAL_ADC_25T85
REF2_5 = 1, TA = 30°C, I(VREF+) = 1 mA
word
0x000C
CAL_ADC_15T85
INCHx = 0x1010, REF2_5 = 0, TA = 85°C
word
0x000A
CAL_ADC_15T30
INCHx = 0x1010, REF2_5 = 0, TA = 30°C
word
0x0008
CAL_ADC_15VREF_FACTOR
REF2_5 = 0, TA = 30°C, I(VREF+) = 0.5 mA
word
0x0006
CAL_ADC_OFFSET
External VREF = 1.5 V, f(ADC10CLK) = 5 MHz
word
0x0004
CAL_ADC_GAIN_FACTOR
External VREF = 1.5 V, f(ADC10CLK) = 5 MHz
word
0x0002
CAL_BC1_1MHz
-
byte
0x0009
CAL_DCO_1MHz
-
byte
0x00008
CAL_BC1_8MHz
-
byte
0x0007
CAL_DCO_8MHz
-
byte
0x0006
CAL_BC1_12MHz
-
byte
0x0005
CAL_DCO_12MHz
-
byte
0x0004
CAL_BC1_16MHz
-
byte
0x0003
CAL_DCO_16MHz
-
byte
0x0002
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Main DCO Characteristics
• All ranges selected by RSELx overlap with RSELx + 1: RSELx = 0 overlaps RSELx = 1, ... RSELx = 14
overlaps RSELx = 15.
• DCO control bits DCOx have a step size as defined by parameter SDCO.
• Modulation control bits MODx select how often fDCO(RSEL,DCO+1) is used within the period of 32 DCOCLK
cycles. The frequency fDCO(RSEL,DCO) is used for the remaining cycles. The frequency is an average equal to:
faverage =
32 × fDCO(RSEL,DCO) × fDCO(RSEL,DCO+1)
MOD × fDCO(RSEL,DCO) + (32 – MOD) × fDCO(RSEL,DCO+1)
Brownout
The brownout circuit is implemented to provide the proper internal reset signal to the device during power on and
power off.
Digital I/O
There are two 8-bit I/O ports implemented:
• All individual I/O bits are independently programmable.
• Any combination of input, output, and interrupt condition(port P1 and port P2 only) is possible.
• Edge-selectable interrupt input capability for all the eight bits of port P1 and port P2, if available.
• Read/write access to port-control registers is supported by all instructions.
• Each I/O has an individually programmable pullup/pulldown resistor.
• Each I/O has an individually programmable pin-oscillator enable bit to enable low-cost touch sensing.
WDT+ Watchdog Timer
The primary function of the watchdog timer (WDT+) module is to perform a controlled system restart after a
software problem occurs. If the selected time interval expires, a system reset is generated. If the watchdog
function is not needed in an application, the module can be disabled or configured as an interval timer and can
generate interrupts at selected time intervals.
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
13
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Timer0_A3
Timer0_A3 is a 16-bit timer/counter with three capture/compare registers. Timer0_A3 can support multiple
capture/compares, PWM outputs, and interval timing. Timer0_A3 also has extensive interrupt capabilities.
Interrupts may be generated from the counter on overflow conditions and from each of the capture/compare
registers.
Table 11. Timer0_A3 Signal Connections (1)
INPUT PIN NUMBER
N20, PW20
PW14
RSA16
DEVICE
INPUT
SIGNAL
P1.0-2
P1.0-2
P1.0-1
TACLK
PinOsc
PinOsc
PinOsc
P1.1-3
P1.1-3
P1.1-2
P1.2-4
P1.2-4
P1.2-3
MODULE
INPUT
NAME
TACLK
ACLK
ACLK
SMCLK
SMCLK
MODULE
OUTPUT
SIGNAL
Timer
NA
OUTPUT PIN NUMBER
N20, PW20
PW14
RSA16
INCLK
TA0.0
CCI0A
P1.2-4
P1.1-3
P1.1-2
ACLK
CCI0B
P1.5-7
P1.5-7
P1.5-6
VSS
GND
VCC
VCC
TA0.1
CCI1A
VSS
GND
VCC
VCC
P1.4-6
P1.4-6
P1.4-5
TA0.2
CCI2A
PinOsc
PinOsc
PinOsc
TA0.2
CCI2B
VSS
GND
VCC
VCC
(1)
MODULE
BLOCK
CCR0
TA0
CCR1
TA1
CCR2
P1.2-4
P1.2-4
P1.2-3
P2.6-19
P2.6-12
P2.6-12
P1.4-6
P1.4-6
P1.4-5
TA2
Only one pin-oscillator must be enabled at a time.
USI
The universal serial interface (USI) module is used for serial data communication and provides the basic
hardware for synchronous communication protocols like SPI and I2C.
ADC10 (MSP430G2x32 only)
The ADC10 module supports fast, 10-bit analog-to-digital conversions. The module implements a 10-bit SAR
core, sample select control, reference generator and data transfer controller, or DTC, for automatic conversion
result handling, allowing ADC samples to be converted and stored without any CPU intervention.
14
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Peripheral File Map
Table 12. Peripherals With Word Access
MODULE
REGISTER DESCRIPTION
ADC10 (MSP430G2x32 devices only) ADC data transfer start address
Timer0_A3
Flash Memory
Watchdog Timer+
REGISTER
NAME
OFFSET
ADC10SA
01BCh
ADC memory
ADC10MEM
01B4h
ADC control register 1
ADC10CTL1
01B2h
ADC control register 0
ADC10CTL0
01B0h
Capture/compare register
TACCR2
0176h
Capture/compare register
TACCR1
0174h
Capture/compare register
TACCR0
0172h
Timer_A register
TAR
0170h
Capture/compare control
TACCTL2
0166h
Capture/compare control
TACCTL1
0164h
Capture/compare control
TACCTL0
0162h
Timer_A control
TACTL
0160h
Timer_A interrupt vector
TAIV
012Eh
Flash control 3
FCTL3
012Ch
Flash control 2
FCTL2
012Ah
Flash control 1
FCTL1
0128h
Watchdog/timer control
WDTCTL
0120h
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
15
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Table 13. Peripherals With Byte Access
MODULE
REGISTER DESCRIPTION
ADC10 (MSP430G2x32 devices only) Analog enable 0
USI
Basic Clock System+
Port P2
Port P1
Special Function
16
Submit Documentation Feedback
REGISTER
NAME
OFFSET
ADC10AE0
04Ah
ADC data transfer control register 1
ADC10DTC1
049h
ADC data transfer control register 0
ADC10DTC0
048h
USI control 0
USICTL0
078h
USI control 1
USICTL1
079h
USI clock control
USICKCTL
07Ah
USI bit counter
USICNT
07Bh
USI shift register
USISR
07Ch
Basic clock system control 3
BCSCTL3
053h
Basic clock system control 2
BCSCTL2
058h
Basic clock system control 1
BCSCTL1
057h
DCO clock frequency control
DCOCTL
056h
Port P2 selection 2
P2SEL2
042h
Port P2 resistor enable
P2REN
02Fh
Port P2 selection
P2SEL
02Eh
Port P2 interrupt enable
P2IE
02Dh
Port P2 interrupt edge select
P2IES
02Ch
Port P2 interrupt flag
P2IFG
02Bh
Port P2 direction
P2DIR
02Ah
Port P2 output
P2OUT
029h
Port P2 input
P2IN
028h
Port P1 selection 2
P1SEL2
041h
Port P1 resistor enable
P1REN
027h
Port P1 selection
P1SEL
026h
Port P1 interrupt enable
P1IE
025h
Port P1 interrupt edge select
P1IES
024h
Port P1 interrupt flag
P1IFG
023h
Port P1 direction
P1DIR
022h
Port P1 output
P1OUT
021h
Port P1 input
P1IN
020h
SFR interrupt flag 2
IFG2
003h
SFR interrupt flag 1
IFG1
002h
SFR interrupt enable 2
IE2
001h
SFR interrupt enable 1
IE1
000h
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Absolute Maximum Ratings (1)
Voltage applied at VCC to VSS
–0.3 V to 4.1 V
Voltage applied to any pin (2)
–0.3 V to VCC + 0.3 V
±2 mA
Diode current at any device pin
Storage temperature range, Tstg
(3)
Unprogrammed device
–55°C to 150°C
Programmed device
–40°C to 85°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages referenced to VSS. The JTAG fuse-blow voltage, VFB, is allowed to exceed the absolute maximum rating. The voltage is
applied to the TEST pin when blowing the JTAG fuse.
Higher temperature may be applied during board soldering according to the current JEDEC J-STD-020 specification with peak reflow
temperatures not higher than classified on the device label on the shipping boxes or reels.
(1)
(2)
(3)
Recommended Operating Conditions
MIN
VCC
Supply voltage
VSS
Supply voltage
TA
Operating free-air temperature
(1)
(2)
MAX
During program execution
1.8
3.6
During flash programming/erase
2.2
3.6
0
Processor frequency (maximum MCLK frequency
using the USART module) (1) (2)
fSYSTEM
NOM
UNIT
V
V
–40
85
VCC = 1.8 V,
Duty cycle = 50% ± 10%
dc
6
VCC = 2.7 V,
Duty cycle = 50% ± 10%
dc
12
VCC = 3.3 V,
Duty cycle = 50% ± 10%
dc
16
°C
MHz
The MSP430 CPU is clocked directly with MCLK. Both the high and low phase of MCLK must not exceed the pulse width of the
specified maximum frequency.
Modules might have a different maximum input clock specification. See the specification of the respective module in this data sheet.
Legend :
System Frequency - MHz
16 MHz
Supply voltage range,
during flash memory
programming
12 MHz
Supply voltage range,
during program execution
6 MHz
1.8 V
Note:
2.7 V
2.2 V
Supply Voltage - V
3.3 V 3.6 V
Minimum processor frequency is defined by system clock. Flash program or erase operations require a minimum VCC
of 2.2 V.
Figure 1. Safe Operating Area
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
17
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Electrical Characteristics
Active Mode Supply Current Into VCC Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1) (2)
PARAMETER
Active mode (AM)
current (1 MHz)
IAM,1MHz
(1)
(2)
TEST CONDITIONS
VCC
fDCO = fMCLK = fSMCLK = 1 MHz,
fACLK = 32768 Hz,
Program executes in flash,
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
CPUOFF = 0, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
MIN
TYP
2.2 V
220
3V
320
MAX
UNIT
µA
400
All inputs are tied to 0 V or to VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF. The internal and external
load capacitance is chosen to closely match the required 9 pF.
Typical Characteristics – Active Mode Supply Current (Into VCC)
5.0
4.0
Active Mode Current − mA
Active Mode Current − mA
f DCO = 16 MHz
4.0
3.0
f DCO = 12 MHz
2.0
f DCO = 8 MHz
1.0
TA = 85 °C
3.0
TA = 25 °C
VCC = 3 V
2.0
TA = 85 °C
TA = 25 °C
1.0
f DCO = 1 MHz
0.0
1.5
2.0
2.5
3.0
3.5
VCC = 2.2 V
4.0
VCC − Supply Voltage − V
Figure 2. Active Mode Current vs VCC, TA = 25°C
18
Submit Documentation Feedback
0.0
0.0
4.0
8.0
12.0
16.0
f DCO − DCO Frequency − MHz
Figure 3. Active Mode Current vs DCO Frequency
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Low-Power Mode Supply Currents (Into VCC) Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1)
PARAMETER
TA
VCC
Low-power mode 0
(LPM0) current (3)
fMCLK = 0 MHz,
fSMCLK = fDCO = 1 MHz,
fACLK = 32768 Hz,
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
CPUOFF = 1, SCG0 = 0, SCG1 = 0,
OSCOFF = 0
25°C
2.2 V
55
µA
ILPM2
Low-power mode 2
(LPM2) current (4)
fMCLK = fSMCLK = 0 MHz,
fDCO = 1 MHz,
fACLK = 32768 Hz,
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
CPUOFF = 1, SCG0 = 0, SCG1 = 1,
OSCOFF = 0
25°C
2.2 V
22
µA
ILPM3,LFXT1
Low-power mode 3
(LPM3) current (4)
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK = 32768 Hz,
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 0
25°C
2.2 V
0.7
1.0
µA
ILPM3,VLO
Low-power mode 3
current, (LPM3) (4)
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK from internal LF oscillator (VLO),
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 0
25°C
2.2 V
0.5
0.7
µA
2.2 V
0.1
0.5
µA
ILPM4
fDCO = fMCLK = fSMCLK = 0 MHz,
fACLK = 0 Hz,
CPUOFF = 1, SCG0 = 1, SCG1 = 1,
OSCOFF = 1
25°C
Low-power mode 4
(LPM4) current (5)
85°C
2.2 V
0.8
1.5
µA
ILPM0,1MHz
(1)
(2)
(3)
(4)
(5)
TEST CONDITIONS
MIN
(2)
TYP
MAX
UNIT
All inputs are tied to 0 V or to VCC. Outputs do not source or sink any current.
The currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF.
Current for brownout and WDT clocked by SMCLK included.
Current for brownout and WDT clocked by ACLK included.
Current for brownout included.
Typical Characteristics Low-Power Mode Supply Currents
2.0
1.0
1.8
0.9
ILPM4 − Low−power mode current − µA
ILPM3 − Low−power mode current − µA
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
1.6
1.4
1.2
VCC = 3.6 V
1.0
VCC = 3 V
0.8
VCC = 2.2 V
0.6
0.4
VCC = 1.8 V
0.2
0.0
−40.0 −20.0 0.0
20.0 40.0 60.0 80.0 100.0 120.0
TA − Temperature − °C
Figure 4. LPM3 Current vs Temperature
Copyright © 2010–2011, Texas Instruments Incorporated
0.8
0.7
0.6
0.5
VCC = 3.6 V
0.4
VCC = 3 V
0.3
VCC = 2.2 V
0.2
0.1
0.0
−40.0 −20.0 0.0
VCC = 1.8 V
20.0 40.0 60.0 80.0 100.0 120.0
TA − Temperature − C
Figure 5. LPM4 Current vs Temperature
Submit Documentation Feedback
19
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Schmitt-Trigger Inputs – Ports Px (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIT+
Positive-going input threshold voltage
VIT–
Negative-going input threshold voltage
Vhys
Input voltage hysteresis (VIT+ – VIT–)
MIN
RPull
Pullup/pulldown resistor
CI
Input capacitance
VIN = VSS or VCC
TYP
MAX
0.45 VCC
0.75 VCC
1.35
2.25
3V
For pullup: VIN = VSS
For pulldown: VIN = VCC
(1)
VCC
UNIT
V
0.25 VCC
0.55 VCC
3V
0.75
1.65
3V
0.3
1
V
3V
20
50
kΩ
35
V
5
pF
An external signal sets the interrupt flag every time the minimum interrupt pulse width t(int) is met. It may be set even with trigger signals
shorter than t(int).
Leakage Current – Ports Px
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
Ilkg(Px.x)
(1)
(2)
TEST CONDITIONS
VCC
(1) (2)
High-impedance leakage current
MIN
3V
MAX
UNIT
±50
nA
The leakage current is measured with VSS or VCC applied to the corresponding pin(s), unless otherwise noted.
The leakage of the digital port pins is measured individually. The port pin is selected for input, and the pullup/pulldown resistor is
disabled.
Outputs – Ports Px
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
I(OHmax) = –6 mA
VOL
Low-level output voltage
I(OLmax) = 6 mA (1)
(1)
VCC
(1)
MIN
TYP
MAX
UNIT
3V
VCC – 0.3
V
3V
VSS + 0.3
V
The maximum total current, I(OHmax) and I(OLmax), for all outputs combined should not exceed ±48 mA to hold the maximum voltage drop
specified.
Output Frequency – Ports Px
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
fPx.y
Port output frequency (with load)
fPort_CLK
(1)
(2)
20
Clock output frequency
TEST CONDITIONS
Px.y, CL = 20 pF, RL = 1 kΩ (1)
Px.y, CL = 20 pF
(2)
VCC
(2)
MIN
TYP
MAX
UNIT
3V
12
MHz
3V
16
MHz
A resistive divider with two 0.5-kΩ resistors between VCC and VSS is used as load. The output is connected to the center tap of the
divider.
The output voltage reaches at least 10% and 90% VCC at the specified toggle frequency.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Typical Characteristics – Outputs
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TYPICAL LOW -LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOL TAGE
TYPICAL LOW -LEVEL OUTPUT CURRENT
vs
LOW-LEVEL OUTPUT VOL TAGE
50.0
VCC = 2.2 V
P1.7
TA = 25°C
25.0
TA = 85°C
20.0
15.0
10.0
5.0
0.0
0.0
0.5
1.0
1.5
2.0
I OL − Typical Low-Level Output Current − mA
I OL − Typical Low-Level Output Current − mA
30.0
VCC = 3 V
P1.7
40.0
TA = 85°C
30.0
20.0
10.0
0.0
0.0
2.5
TA = 25°C
VOL − Low-Level Output Voltage − V
0.5
1.0
Figure 6.
2.5
3.0
3.5
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
0.0
0.0
VCC = 2.2 V
P1.7
I OH − Typical High-Level Output Current − mA
I OH − Typical High-Level Output Current − mA
2.0
Figure 7.
TYPICAL HIGH-LEVEL OUTPUT CURRENT
vs
HIGH-LEVEL OUTPUT VOLTAGE
−5.0
−10.0
−15.0
TA = 85°C
−20.0
−25.0
0.0
1.5
VOL − Low-Level Output Voltage − V
TA = 25°C
0.5
1.0
1.5
2.0
VOH − High-Level Output Voltage − V
Figure 8.
Copyright © 2010–2011, Texas Instruments Incorporated
2.5
VCC = 3 V
P1.7
−10.0
−20.0
−30.0
TA = 85°C
−40.0
TA = 25°C
−50.0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VOH − High-Level Output Voltage − V
Figure 9.
Submit Documentation Feedback
21
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Pin-Oscillator Frequency – Ports Px
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
foP1.x
Port output oscillation frequency
foP2.x
Port output oscillation frequency
foP2.6/7
Port output oscillation frequency
(1)
(2)
TEST CONDITIONS
P1.y, CL = 10 pF, RL = 100 kΩ
VCC
MIN
(1) (2)
3V
P1.y, CL = 20 pF, RL = 100 kΩ (1) (2)
P2.0 to P2.5, CL = 10 pF, RL = 100 kΩ (1) (2)
P2.0 to P2.5, CL = 20 pF, RL = 100 kΩ (1) (2)
P2.6 and P2.7, CL = 20 pF, RL = 100
kΩ (1) (2)
3V
3V
TYP
MAX
1400
UNIT
kHz
900
1800
kHz
1000
700
kHz
A resistive divider with two 100-kΩ resistors between VCC and VSS is used as load. The output is connected to the center tap of the
divider.
The output voltage oscillates with a typical amplitude of 700 mV at the specified toggle frequency.
Typical Characteristics – Pin-Oscillator Frequency
TYPICAL OSCILLATING FREQUENCY
vs
LOAD CAPACITANCE
TYPICAL OSCILLATING FREQUENCY
vs
LOAD CAPACITANCE
1.50
VCC = 2.2 V
1.35
1.20
1.05
P1.y
0.90
P2.0 ... P2.5
0.75
P2.6, P2.7
0.60
0.45
0.30
0.15
0.00
VCC = 3.0 V
1.35
1.20
1.05
P1.y
0.90
P2.0 ... P2.5
0.75
P2.6, P2.7
0.60
0.45
0.30
0.15
0.00
10
50
100
CLOAD − External Capacitance − pF
Figure 10.
22
fosc − Typical Oscillation Frequency − MHz
fosc − Typical Oscillation Frequency − MHz
1.50
Submit Documentation Feedback
10
50
100
CLOAD − External Capacitance − pF
Figure 11.
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
POR/Brownout Reset (BOR) (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
VCC(start)
See Figure 12
dVCC/dt ≤ 3 V/s
V(B_IT–)
See Figure 12 through Figure 14
dVCC/dt ≤ 3 V/s
1.40
V
Vhys(B_IT–)
See Figure 12
dVCC/dt ≤ 3 V/s
140
mV
td(BOR)
See Figure 12
t(reset)
Pulse length needed at RST/NMI pin to
accepted reset internally
(1)
0.7 × V(B_IT–)
UNIT
V
2000
2.2 V
2
µs
µs
The current consumption of the brownout module is already included in the ICC current consumption data. The voltage level V(B_IT–) +
Vhys(B_IT–)is ≤ 1.8 V.
VCC
Vhys(B_IT−)
V(B_IT−)
VCC(start)
1
0
t d(BOR)
Figure 12. POR/Brownout Reset (BOR) vs Supply Voltage
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
23
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Typical Characteristics – POR/Brownout Reset (BOR)
VCC
3V
2
VCC(drop) − V
VCC = 3 V
Typical Conditions
t pw
1.5
1
VCC(drop)
0.5
0
0.001
1
1000
1 ns
t pw − Pulse Width − µs
1 ns
t pw − Pulse Width − µs
Figure 13. VCC(drop) Level With a Square Voltage Drop to Generate a POR/Brownout Signal
VCC
2
t pw
3V
VCC(drop) − V
VCC = 3 V
1.5
Typical Conditions
1
VCC(drop)
0.5
0
0.001
t f = tr
1
t pw − Pulse Width − µs
1000
tf
tr
t pw − Pulse Width − µs
Figure 14. VCC(drop) Level With a Triangle Voltage Drop to Generate a POR/Brownout Signal
24
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
DCO Frequency
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC
Supply voltage
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
RSELx < 14
1.8
3.6
V
RSELx = 14
2.2
3.6
V
RSELx = 15
3
3.6
V
0.14
MHz
0.17
MHz
fDCO(0,0)
DCO frequency (0, 0)
RSELx = 0, DCOx = 0, MODx = 0
3V
0.06
fDCO(0,3)
DCO frequency (0, 3)
RSELx = 0, DCOx = 3, MODx = 0
3V
0.07
fDCO(1,3)
DCO frequency (1, 3)
RSELx = 1, DCOx = 3, MODx = 0
3V
0.15
MHz
fDCO(2,3)
DCO frequency (2, 3)
RSELx = 2, DCOx = 3, MODx = 0
3V
0.21
MHz
fDCO(3,3)
DCO frequency (3, 3)
RSELx = 3, DCOx = 3, MODx = 0
3V
0.30
MHz
fDCO(4,3)
DCO frequency (4, 3)
RSELx = 4, DCOx = 3, MODx = 0
3V
0.41
MHz
fDCO(5,3)
DCO frequency (5, 3)
RSELx = 5, DCOx = 3, MODx = 0
3V
0.58
MHz
fDCO(6,3)
DCO frequency (6, 3)
RSELx = 6, DCOx = 3, MODx = 0
3V
0.54
1.06
MHz
fDCO(7,3)
DCO frequency (7, 3)
RSELx = 7, DCOx = 3, MODx = 0
3V
0.80
1.50
MHz
fDCO(8,3)
DCO frequency (8, 3)
RSELx = 8, DCOx = 3, MODx = 0
3V
1.6
MHz
fDCO(9,3)
DCO frequency (9, 3)
RSELx = 9, DCOx = 3, MODx = 0
3V
2.3
MHz
fDCO(10,3)
DCO frequency (10, 3)
RSELx = 10, DCOx = 3, MODx = 0
3V
3.4
MHz
fDCO(11,3)
DCO frequency (11, 3)
RSELx = 11, DCOx = 3, MODx = 0
3V
4.25
fDCO(12,3)
DCO frequency (12, 3)
RSELx = 12, DCOx = 3, MODx = 0
3V
4.30
7.30
MHz
fDCO(13,3)
DCO frequency (13, 3)
RSELx = 13, DCOx = 3, MODx = 0
3V
6.00
9.60
MHz
fDCO(14,3)
DCO frequency (14, 3)
RSELx = 14, DCOx = 3, MODx = 0
3V
8.60
13.9
MHz
fDCO(15,3)
DCO frequency (15, 3)
RSELx = 15, DCOx = 3, MODx = 0
3V
12.0
18.5
MHz
fDCO(15,7)
DCO frequency (15, 7)
RSELx = 15, DCOx = 7, MODx = 0
3V
16.0
26.0
MHz
SRSEL
Frequency step between
range RSEL and RSEL+1
SRSEL = fDCO(RSEL+1,DCO)/fDCO(RSEL,DCO)
3V
1.35
ratio
SDCO
Frequency step between
tap DCO and DCO+1
SDCO = fDCO(RSEL,DCO+1)/fDCO(RSEL,DCO)
3V
1.08
ratio
Measured at SMCLK output
3V
50
Duty cycle
Copyright © 2010–2011, Texas Instruments Incorporated
MHz
Submit Documentation Feedback
%
25
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Calibrated DCO Frequencies – Tolerance
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TA
VCC
MIN
TYP
MAX
UNIT
1-MHz tolerance over
temperature (1)
BCSCTL1= CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
calibrated at 30°C and 3 V
0°C to 85°C
3V
-3
±0.5
+3
%
1-MHz tolerance over VCC
BCSCTL1= CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
calibrated at 30°C and 3 V
30°C
1.8 V to 3.6 V
-3
±2
+3
%
1-MHz tolerance overall
BCSCTL1= CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ,
calibrated at 30°C and 3 V
-40°C to 85°C
1.8 V to 3.6 V
-6
±3
+6
%
8-MHz tolerance over
temperature (1)
BCSCTL1= CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
calibrated at 30°C and 3 V
0°C to 85°C
3V
-3
±0.5
+3
%
8-MHz tolerance over VCC
BCSCTL1= CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
calibrated at 30°C and 3 V
30°C
2.2 V to 3.6 V
-3
±2
+3
%
8-MHz tolerance overall
BCSCTL1= CALBC1_8MHZ,
DCOCTL = CALDCO_8MHZ,
calibrated at 30°C and 3 V
-40°C to 85°C
2.2 V to 3.6 V
-6
±3
+6
%
12-MHz tolerance over
temperature (1)
BCSCTL1= CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
calibrated at 30°C and 3 V
0°C to 85°C
3V
-3
±0.5
+3
%
12-MHz tolerance over VCC
BCSCTL1= CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
calibrated at 30°C and 3 V
30°C
2.7 V to 3.6 V
-3
±2
+3
%
12-MHz tolerance overall
BCSCTL1= CALBC1_12MHZ,
DCOCTL = CALDCO_12MHZ,
calibrated at 30°C and 3 V
-40°C to 85°C
2.7 V to 3.6 V
-6
±3
+6
%
16-MHz tolerance over
temperature (1)
BCSCTL1= CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
calibrated at 30°C and 3 V
0°C to 85°C
3.3 V
-3
±0.5
+3
%
16-MHz tolerance over VCC
BCSCTL1= CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
calibrated at 30°C and 3 V
30°C
3.3 V to 3.6 V
-3
±2
+3
%
16-MHz tolerance overall
BCSCTL1= CALBC1_16MHZ,
DCOCTL = CALDCO_16MHZ,
calibrated at 30°C and 3 V
-40°C to 85°C
3.3 V to 3.6 V
-6
±3
+6
%
(1)
26
This is the frequency change from the measured frequency at 30°C over temperature.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Wake-Up From Lower-Power Modes (LPM3/4)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
tDCO,LPM3/4
DCO clock wake-up time from
LPM3/4 (1)
tCPU,LPM3/4
CPU wake-up time from LPM3/4 (2)
(1)
(2)
VCC
BCSCTL1 = CALBC1_1MHZ,
DCOCTL = CALDCO_1MHZ
MIN
3V
TYP
MAX
1.5
UNIT
µs
1/fMCLK +
tClock,LPM3/4
The DCO clock wake-up time is measured from the edge of an external wake-up signal (for example, a port interrupt) to the first clock
edge observable externally on a clock pin (MCLK or SMCLK).
Parameter applicable only if DCOCLK is used for MCLK.
Typical Characteristics – DCO Clock Wake-Up Time From LPM3/4
DCO Wake Time − us
10.00
RSELx = 0...11
RSELx = 12...15
1.00
0.10
0.10
1.00
10.00
DCO Frequency − MHz
Figure 15. DCO Wake-Up Time From LPM3 vs DCO Frequency
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
27
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Crystal Oscillator, XT1, Low-Frequency Mode (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
fLFXT1,LF
LFXT1 oscillator crystal
frequency, LF mode 0, 1
fLFXT1,LF,logic
LFXT1 oscillator logic level
square wave input frequency, XTS = 0, XCAPx = 0, LFXT1Sx = 3
LF mode
OALF
Oscillation allowance for
LF crystals
Integrated effective load
capacitance, LF mode (2)
CL,eff
XTS = 0, LFXT1Sx = 0 or 1
32768
XTS = 0, LFXT1Sx = 0,
fLFXT1,LF = 32768 Hz, CL,eff = 12 pF
200
1
XTS = 0, XCAPx = 1
5.5
XTS = 0, XCAPx = 2
8.5
XTS = 0, XCAPx = 3
11
Oscillator fault frequency,
LF mode (3)
XTS = 0, XCAPx = 0, LFXT1Sx = 3 (4)
UNIT
Hz
50000
Hz
kΩ
XTS = 0, XCAPx = 0
fFault,LF
(4)
10000
500
LF mode
(3)
1.8 V to 3.6 V
MAX
32768
XTS = 0, LFXT1Sx = 0,
fLFXT1,LF = 32768 Hz, CL,eff = 6 pF
Duty cycle
(2)
TYP
1.8 V to 3.6 V
XTS = 0, Measured at P2.0/ACLK,
fLFXT1,LF = 32768 Hz
(1)
MIN
2.2 V
30
2.2 V
10
50
pF
70
%
10000
Hz
To improve EMI on the XT1 oscillator, the following guidelines should be observed.
(a) Keep the trace between the device and the crystal as short as possible.
(b) Design a good ground plane around the oscillator pins.
(c) Prevent crosstalk from other clock or data lines into oscillator pins XIN and XOUT.
(d) Avoid running PCB traces underneath or adjacent to the XIN and XOUT pins.
(e) Use assembly materials and praxis to avoid any parasitic load on the oscillator XIN and XOUT pins.
(f) If conformal coating is used, ensure that it does not induce capacitive/resistive leakage between the oscillator pins.
(g) Do not route the XOUT line to the JTAG header to support the serial programming adapter as shown in other documentation. This
signal is no longer required for the serial programming adapter.
Includes parasitic bond and package capacitance (approximately 2 pF per pin).
Because the PCB adds additional capacitance, it is recommended to verify the correct load by measuring the ACLK frequency. For a
correct setup, the effective load capacitance should always match the specification of the used crystal.
Frequencies below the MIN specification set the fault flag. Frequencies above the MAX specification do not set the fault flag.
Frequencies in between might set the flag.
Measured with logic-level input frequency but also applies to operation with crystals.
Internal Very-Low-Power Low-Frequency Oscillator (VLO)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
TA
VCC
MIN
TYP
MAX
fVLO
VLO frequency
PARAMETER
-40°C to 85°C
3V
4
12
20
dfVLO/dT
VLO frequency temperature drift
-40°C to 85°C
3V
dfVLO/dVCC
VLO frequency supply voltage drift
25°C
1.8 V to 3.6 V
UNIT
kHz
0.5
%/°C
4
%/V
Timer_A
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fTA
Timer_A input clock frequency
SMCLK
Duty cycle = 50% ± 10%
tTA,cap
Timer_A capture timing
TA0, TA1
28
Submit Documentation Feedback
VCC
MIN
TYP
fSYSTEM
3V
20
MAX
UNIT
MHz
ns
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
USI, Universal Serial Interface
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
fUSI
USI module clock frequency
External: SCLK,
Duty cycle = 50% ± 10%
f(SCLK)
Serial clock frequency, slave mode
SPI slave mode
Low-level output voltage on SDA and SCL
USI module in I2C mode,
I(OLmax) = 1.5 mA
VOL,I2C
VCC
MIN
TYP
MAX
fSYSTEM
UNIT
MHz
3V
6
3V
VSS
+ 0.4
VSS
MHz
V
Typical Characteristics – USI Low-Level Output Voltage on SDA and SCL
5.0
5.0
VCC = 3 V
TA = 25°C
I OL − Low-Level Output Current − mA
I OL − Low-Level Output Current − mA
VCC = 2.2 V
4.0
TA = 25°C
3.0
TA = 85°C
2.0
1.0
0.0
0.0
0.2
0.4
0.6
0.8
1.0
VOL − Low-Level Output Voltage − V
Figure 16. USI Low-Level Output Voltage vs Output
Current
Copyright © 2010–2011, Texas Instruments Incorporated
4.0
TA = 85°C
3.0
2.0
1.0
0.0
0.0
0.2
0.4
0.6
0.8
1.0
VOL − Low-Level Output Voltage − V
Figure 17. USI Low-Level Output Voltage vs Output
Current
Submit Documentation Feedback
29
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
10-Bit ADC, Power Supply and Input Range Conditions (MSP430G2x32 Only)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (1)
PARAMETER
VCC
TEST CONDITIONS
Analog supply voltage
VAx
Analog input voltage
IADC10
IREF+
VCC
VSS = 0 V
(2)
ADC10 supply current
TA
(3)
Reference supply current,
reference buffer disabled (4)
All Ax terminals, Analog inputs
selected in ADC10AE register
fADC10CLK = 5.0 MHz,
ADC10ON = 1, REFON = 0,
ADC10SHT0 = 1, ADC10SHT1 = 0,
ADC10DIV = 0
fADC10CLK = 5.0 MHz,
ADC10ON = 0, REF2_5V = 0,
REFON = 1, REFOUT = 0
fADC10CLK = 5.0 MHz,
ADC10ON = 0, REF2_5V = 1,
REFON = 1, REFOUT = 0
3V
25°C
3V
MIN
TYP
MAX
UNIT
2.2
3.6
V
0
VCC
V
0.6
mA
0.25
25°C
3V
mA
0.25
IREFB,0
Reference buffer supply
current with ADC10SR = 0 (4)
fADC10CLK = 5.0 MHz,
ADC10ON = 0, REFON = 1,
REF2_5V = 0, REFOUT = 1,
ADC10SR = 0
25°C
3V
1.1
mA
IREFB,1
Reference buffer supply
current with ADC10SR = 1 (4)
fADC10CLK = 5.0 MHz,
ADC10ON = 0, REFON = 1,
REF2_5V = 0, REFOUT = 1,
ADC10SR = 1
25°C
3V
0.5
mA
CI
Input capacitance
Only one terminal Ax can be selected
at one time
25°C
3V
RI
Input MUX ON resistance
0 V ≤ VAx ≤ VCC
25°C
3V
(1)
(2)
(3)
(4)
30
27
1000
pF
Ω
The leakage current is defined in the leakage current table with Px.x/Ax parameter.
The analog input voltage range must be within the selected reference voltage range VR+ to VR– for valid conversion results.
The internal reference supply current is not included in current consumption parameter IADC10.
The internal reference current is supplied via terminal VCC. Consumption is independent of the ADC10ON control bit, unless a
conversion is active. The REFON bit enables the built-in reference to settle before starting an A/D conversion.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
10-Bit ADC, Built-In Voltage Reference (MSP430G2x32 Only)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC,REF+
IVREF+ ≤ 1 mA, REF2_5V = 0
Positive built-in reference
analog supply voltage range IVREF+ ≤ 1 mA, REF2_5V = 1
VREF+
Positive built-in reference
voltage
ILD,VREF+
Maximum VREF+ load
current
VREF+ load regulation
IVREF+ ≤ IVREF+max, REF2_5V = 0
IVREF+ ≤ IVREF+max, REF2_5V = 1
VCC
IVREF+ = 500 µA ± 100 µA,
Analog input voltage VAx ≉ 1.25 V,
REF2_5V = 1
TYP
MAX
2.2
3V
UNIT
V
2.9
3V
IVREF+ = 500 µA ± 100 µA,
Analog input voltage VAx ≉ 0.75 V,
REF2_5V = 0
MIN
1.41
1.5
1.59
2.35
2.5
2.65
±1
V
mA
±2
3V
LSB
±2
VREF+ load regulation
response time
IVREF+ = 100 µA→900 µA,
VAx ≉ 0.5 × VREF+,
Error of conversion result ≤ 1 LSB,
ADC10SR = 0
3V
400
ns
CVREF+
Maximum capacitance at
pin VREF+
IVREF+ ≤ ±1 mA, REFON = 1, REFOUT = 1
3V
100
pF
TCREF+
Temperature coefficient
IVREF+ = const with 0 mA ≤ IVREF+ ≤ 1 mA
3V
±100
ppm/
°C
tREFON
Settling time of internal
reference voltage to 99.9%
VREF
IVREF+ = 0.5 mA, REF2_5V = 0,
REFON = 0 → 1
3.6 V
30
µs
tREFBURST
Settling time of reference
buffer to 99.9% VREF
IVREF+ = 0.5 mA,
REF2_5V = 1, REFON = 1,
REFBURST = 1, ADC10SR = 0
3V
2
µs
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
31
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
10-Bit ADC, External Reference (1) (MSP430G2x32 Only)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VEREF+
TEST CONDITIONS
Positive external reference input
voltage range (2)
1.4
3
0
1.2
V
1.4
VCC
V
Differential external reference
input voltage range,
ΔVEREF = VEREF+ – VEREF–
VEREF+ > VEREF–
(1)
(2)
(3)
(4)
(5)
UNIT
VEREF– ≤ VEREF+ ≤ VCC – 0.15 V,
SREF1 = 1, SREF0 = 1 (3)
ΔVEREF
Static input current into VEREF–
MAX
VCC
VEREF+ > VEREF–
IVEREF–
TYP
1.4
Negative external reference input
voltage range (4)
Static input current into VEREF+
MIN
VEREF+ > VEREF–,
SREF1 = 1, SREF0 = 0
VEREF–
IVEREF+
VCC
V
(5)
0 V ≤ VEREF+ ≤ VCC,
SREF1 = 1, SREF0 = 0
±1
0 V ≤ VEREF+ ≤ VCC – 0.15 V ≤ 3 V,
SREF1 = 1, SREF0 = 1 (3)
0 V ≤ VEREF– ≤ VCC
µA
3V
0
±1
3V
µA
The external reference is used during conversion to charge and discharge the capacitance array. The input capacitance, CI, is also the
dynamic load for an external reference during conversion. The dynamic impedance of the reference supply should follow the
recommendations on analog-source impedance to allow the charge to settle for 10-bit accuracy.
The accuracy limits the minimum positive external reference voltage. Lower reference voltage levels may be applied with reduced
accuracy requirements.
Under this condition the external reference is internally buffered. The reference buffer is active and requires the reference buffer supply
current IREFB. The current consumption can be limited to the sample and conversion period with REBURST = 1.
The accuracy limits the maximum negative external reference voltage. Higher reference voltage levels may be applied with reduced
accuracy requirements.
The accuracy limits the minimum external differential reference voltage. Lower differential reference voltage levels may be applied with
reduced accuracy requirements.
10-Bit ADC, Timing Parameters (MSP430G2x32 Only)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
ADC10SR = 0
fADC10CLK
ADC10 input clock
frequency
For specified performance of
ADC10 linearity parameters
fADC10OSC
ADC10 built-in oscillator
frequency
ADC10DIVx = 0, ADC10SSELx = 0,
fADC10CLK = fADC10OSC
ADC10 built-in oscillator, ADC10SSELx = 0,
fADC10CLK = fADC10OSC
tCONVERT
Conversion time
tADC10ON
Turn-on settling time of
the ADC
(1)
ADC10SR = 1
VCC
MIN
TYP
MAX
0.45
6.3
0.45
1.5
3V
3.7
6.3
3V
2.06
3.51
3V
UNIT
MHz
MHz
µs
13 ×
ADC10DIV ×
1/fADC10CLK
fADC10CLK from ACLK, MCLK, or SMCLK:
ADC10SSELx ≠ 0
(1)
100
ns
The condition is that the error in a conversion started after tADC10ON is less than ±0.5 LSB. The reference and input signal are already
settled.
10-Bit ADC, Linearity Parameters (MSP430G2x32 Only)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
MAX
UNIT
EI
Integral linearity error
PARAMETER
3V
±1
LSB
ED
Differential linearity error
3V
±1
LSB
EO
Offset error
3V
±1
LSB
EG
Gain error
3V
±1.1
±2
LSB
ET
Total unadjusted error
3V
±2
±5
LSB
32
Submit Documentation Feedback
TEST CONDITIONS
Source impedance RS < 100 Ω
VCC
MIN
TYP
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
10-Bit ADC, Temperature Sensor and Built-In VMID (MSP430G2x32 Only)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
ISENSOR
Temperature sensor supply
current (1)
TCSENSOR
TEST CONDITIONS
VCC
REFON = 0, INCHx = 0Ah,
TA = 25°C
ADC10ON = 1, INCHx = 0Ah
(2)
60
3V
3.55
tSensor(sample)
ADC10ON = 1, INCHx = 0Ah,
Error of conversion result ≤ 1 LSB
3V
IVMID
Current into divider at channel 11
ADC10ON = 1, INCHx = 0Bh
3V
VMID
VCC divider at channel 11
ADC10ON = 1, INCHx = 0Bh,
VMID ≉ 0.5 × VCC
3V
tVMID(sample)
Sample time required if channel
11 is selected (5)
ADC10ON = 1, INCHx = 0Bh,
Error of conversion result ≤ 1 LSB
3V
(2)
(3)
(4)
(5)
TYP
3V
Sample time required if channel
10 is selected (3)
(1)
MIN
MAX
UNIT
µA
mV/°C
µs
30
(4)
1.5
µA
V
1220
ns
The sensor current ISENSOR is consumed if (ADC10ON = 1 and REFON = 1) or (ADC10ON = 1 and INCH = 0Ah and sample signal is
high). When REFON = 1, ISENSOR is included in IREF+. When REFON = 0, ISENSOR applies during conversion of the temperature sensor
input (INCH = 0Ah).
The following formula can be used to calculate the temperature sensor output voltage:
VSensor,typ = TCSensor (273 + T [°C] ) + VOffset,sensor [mV] or
VSensor,typ = TCSensor T [°C] + VSensor(TA = 0°C) [mV]
The typical equivalent impedance of the sensor is 51 kΩ. The sample time required includes the sensor-on time tSENSOR(on).
No additional current is needed. The VMID is used during sampling.
The on-time tVMID(on) is included in the sampling time tVMID(sample); no additional on time is needed.
Flash Memory
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
MIN
TYP
MAX
UNIT
VCC(PGM/ERASE)
Program and erase supply voltage
2.2
3.6
V
fFTG
Flash timing generator frequency
257
476
kHz
IPGM
Supply current from VCC during program
2.2 V/3.6 V
1
5
mA
IERASE
Supply current from VCC during erase
2.2 V/3.6 V
1
7
mA
tCPT
Cumulative program time (1)
2.2 V/3.6 V
10
ms
tCMErase
Cumulative mass erase time
2.2 V/3.6 V
20
4
Program/erase endurance
10
ms
5
10
Data retention duration
TJ = 25°C
tWord
Word or byte program time
(2)
30
tFTG
tBlock,
0
Block program time for first byte or word
(2)
25
tFTG
tBlock,
1-63
Block program time for each additional
byte or word
(2)
18
tFTG
tBlock,
End
Block program end-sequence wait time
(2)
6
tFTG
tMass Erase
Mass erase time
(2)
10593
tFTG
tSeg Erase
Segment erase time
(2)
4819
tFTG
(1)
(2)
100
cycles
tRetention
years
The cumulative program time must not be exceeded when writing to a 64-byte flash block. This parameter applies to all programming
methods: individual word/byte write and block write modes.
These values are hardwired into the Flash Controller's state machine (tFTG = 1/fFTG).
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
33
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
RAM
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
V(RAMh)
(1)
RAM retention supply voltage
TEST CONDITIONS
(1)
MIN
CPU halted
MAX
1.6
UNIT
V
This parameter defines the minimum supply voltage VCC when the data in RAM remains unchanged. No program execution should
happen during this supply voltage condition.
JTAG and Spy-Bi-Wire Interface
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
MAX
UNIT
fSBW
Spy-Bi-Wire input frequency
PARAMETER
2.2 V
0
20
MHz
tSBW,Low
Spy-Bi-Wire low clock pulse length
2.2 V
0.025
15
µs
tSBW,En
Spy-Bi-Wire enable time
(TEST high to acceptance of first clock edge (1))
2.2 V
1
µs
tSBW,Ret
Spy-Bi-Wire return to normal operation time
2.2 V
15
100
fTCK
TCK input frequency (2)
2.2 V
0
5
MHz
RInternal
Internal pulldown resistance on TEST
2.2 V
25
90
kΩ
(1)
(2)
TEST CONDITIONS
VCC
MIN
TYP
60
µs
Tools accessing the Spy-Bi-Wire interface need to wait for the maximum tSBW,En time after pulling the TEST/SBWCLK pin high before
applying the first SBWCLK clock edge.
fTCK may be restricted to meet the timing requirements of the module selected.
JTAG Fuse (1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
VCC(FB)
Supply voltage during fuse-blow condition
VFB
Voltage level on TEST for fuse blow
IFB
Supply current into TEST during fuse blow
tFB
Time to blow fuse
(1)
34
TEST CONDITIONS
TA = 25°C
MIN
MAX
2.5
6
UNIT
V
7
V
100
mA
1
ms
Once the fuse is blown, no further access to the JTAG/Test, Spy-Bi-Wire, and emulation feature is possible, and JTAG is switched to
bypass mode.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
PIN SCHEMATICS
Port P1 Pin Schematic: P1.0 to P1.2, Input/Output With Schmitt Trigger
To ADC10 *
INCHx = y *
ADC10AE0.y *
PxSEL2.y
PxSEL.y
PxDIR.y
0
1
0
Direction
0: Input
1: Output
2
3
PxSEL2.y
PxSEL.y
PxREN.y
0
1
1
0
1
PxSEL2.y
PxSEL.y
PxOUT.y
DVSS
DVCC
0
1
1
0
From Module
1
0
3
2
Bus
Keeper
EN
P1.0/TA0CLK/ACLK/A0*
P1.1/TA0.0/A1*
P1.2/TA0.1/A2*
TAx.y
TAxCLK
PxIN.y
EN
To Module
D
PxIE.y
PxIRQ.y
Q
EN
Set
PxIFG.y
PxSEL.y
PxIES.y
Interrupt
Edge
Select
* Note: MSP430G2x32 devices only. MSP430G2x02 devices have no ADC10.
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
35
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Table 14. Port P1 (P1.0 to P1.2) Pin Functions
PIN NAME
(P1.x)
CONTROL BITS / SIGNALS (1)
x
FUNCTION
P1DIR.x
P1SEL.x
P1SEL2.x
ADC10AE.x
(INCH.y=1) (2)
P1.0/
P1.x (I/O)
I: 0; O: 1
0
0
0
TA0CLK/
TA0.TACLK
0
1
0
0
ACLK
1
1
0
0
A0 (2)/
A0
X
X
X
1 (y = 0)
Pin Osc
Capacitive sensing
P1.1/
P1.x (I/O)
TA0.0/
ACLK/
0
x
0
1
0
I: 0; O: 1
0
0
0
TA0.0
1
1
0
0
TA0.CCI0A
0
1
0
0
A1 (2)/
A1
X
X
X
1 (y = 1)
Pin Osc
Capacitive sensing
P1.2/
P1.x (I/O)
TA0.1/
1
X
0
1
0
I: 0; O: 1
0
0
0
TA0.1
1
1
0
0
TA0.CCI1A
0
1
0
0
A2 (2)/
A2
X
X
X
1 (y = 2)
Pin Osc
Capacitive sensing
X
0
1
0
2
(1)
(2)
36
X = don't care
MSP430G2x32 devices only
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Port P1 Pin Schematic: P1.3, Input/Output With Schmitt Trigger
SREF2 *
VSS
0
1
To ADC10 VREF- *
To ADC10 *
INCHx = y *
ADC10AE0.y *
PxSEL2.y PxSEL.y
PxDIR.y
0,2,3
1
Direction
0: Input
1: Output
PxSEL2.y
PxSEL.y
PxREN.y
0
1
1
0
1
PxSEL2.y
PxSEL.y
PxOUT.y
From ADC10 *
DVSS
DVCC
0
1
1
0
1
2
Bus
Keeper
EN
3
P1.3/ADC10CLK*/A3*/VREF-*/VEREF-*
TAx.y
TAxCLK
PxIN.y
EN
To Module
D
PxIE.y
PxIRQ.y
EN
Q
Set
PxIFG.y
PxSEL.y
PxIES.y
Interrupt
Edge
Select
* Note: MSP430G2x32 devices only. MSP430G2x02 devices have no ADC10.
Table 15. Port P1 (P1.3) Pin Functions
PIN NAME
(P1.x)
CONTROL BITS / SIGNALS (1)
x
FUNCTION
P1DIR.x
P1SEL.x
P1SEL2.x
ADC10AE.x
(INCH.x=1) (2)
0
P1.3/
P1.x (I/O)
I: 0; O: 1
0
0
ADC10CLK (2)/
ADC10CLK
1
1
0
0
A3 (2)/
A3
X
X
X
1 (y = 3)
VREF- (2)/
3
VREF-
X
X
X
1
VEREF- (2)/
VEREF-
X
X
X
1
Pin Osc
Capacitive sensing
X
0
1
0
(1)
(2)
X = don't care
MSP430G2x32 devices only
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
37
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Port P1 Pin Schematic: P1.4, Input/Output With Schmitt Trigger
From/To ADC10 Ref+ *
To ADC10 *
INCHx = y *
ADC10AE0.y *
PxSEL.y
PxDIR.y
0
1
Direction
0: Input
1: Output
PxSEL2.y
PxSEL.y
PxREN.y
0
1
1
0
1
PxSEL2.y
PxSEL.y
DVSS
DVCC
PxOUT.y
SMCLK
0
1
from Timer
2
3
0
1
1
Bus
Keeper
EN
P1.4/SMCLK/TA0.2/A4*/VREF+*/VEREF+*/TCK
TAx.y
TAxCLK
PxIN.y
EN
D
To Module
PxIE.y
EN
Q
Set
PxIRQ.y
PxIFG.y
PxSEL.y
PxIES.y
Interrupt
Edge
Select
From JTAG
To JTAG
* Note: MSP430G2x32 devices only. MSP430G2x02 devices have no ADC10.
Table 16. Port P1 (P1.4) Pin Functions
PIN NAME
(P1.x)
CONTROL BITS / SIGNALS (1)
x
FUNCTION
P1DIR.x
P1SEL.x
P1SEL2.x
ADC10AE.x
(INCH.x=1) (2)
JTAG Mode
CAPD.y
P1.4/
P1.x (I/O)
I: 0; O: 1
0
0
0
0
0
SMCLK/
SMCLK
1
1
0
0
0
0
TA0.2/
TA0.2
1
1
1
0
0
0
TA0.CCI2A
0
1
1
0
0
0
VREF+
X
X
X
1
0
0
VEREF+ (2)/
VEREF+
X
X
X
1
0
0
A4 (2)/
A4
X
X
X
1 (y = 4)
0
0
TCK/
TCK
X
X
X
0
1
0
Pin Osc
Capacitive sensing
X
0
1
0
0
0
VREF+ (2)/
(1)
(2)
38
4
X = don't care
MSP430G2x32 devices only
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Port P1 Pin Schematic: P1.5 to P1.7, Input/Output With Schmitt Trigger
To ADC10 *
INCHx = y *
ADC10AE0.y *
PxSEL2.y
PxSEL.y
PxDIR.y
0
From Module
1
Direction
0: Input
1: Output
2
3
PxSEL2.y
PxSEL.y
PxREN.y
0
1
1
0
1
PxSEL2.y
PxSEL.y
PxOUT.y
DVSS
DVCC
0
1
1
0
From Module
1
0
3
2
Bus
Keeper
EN
P1.5/TA0.0/SCLK/A5*/TMS
P1.6/TA0.1/SDO/SCL/A6*/TDI/TCLK
P1.7//SDI/SDA/A7*/TDO/TDI
TAx.y
TAxCLK
PxIN.y
EN
D
To Module
PxIE.y
PxIRQ.y
Q
EN
Set
PxIFG.y
PxSEL.y
PxIES.y
Interrupt
Edge
Select
From JTAG
To JTAG
* Note: MSP430G2x32 devices only. MSP430G2x02 devices have no ADC10.
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
39
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Table 17. Port P1 (P1.5 to P1.7) Pin Functions
PIN NAME
(P1.x)
CONTROL BITS / SIGNALS (1)
x
FUNCTION
P1DIR.x
P1SEL.x
P1SEL2.x
USIP.x
JTAG Mode
ADC10AE.x
(INCH.x=1) (2)
I: 0; O: 1
0
0
0
0
0
1
1
0
0
0
0
from USI
1
0
1
0
0
A5
X
X
X
0
0
1 (y = 5)
TMS/
TMS
X
X
X
0
1
0
Pin Osc
Capacitive sensing
X
0
1
0
0
0
P1.6/
P1.x (I/O)
I: 0; O: 1
0
0
0
0
0
TA0.1/
TA0.1
1
1
0
0
0
0
SDO/
SPI mode
from USI
1
0
!
0
0
I2C mode
P1.5/
P1.x (I/O)
TA0.0/
TA0.0
SCLK/
SPI mode
5
A5 (2)/
SCL/
from USI
1
0
!
0
0
A6 (2)/
6
A6
X
X
X
0
0
1 (y = 6)
TDI/TCLK/
TDI/TCLK
X
X
X
0
1
0
Pin Osc
Capacitive sensing
X
0
1
0
0
0
P1.7/
P1.x (I/O)
I: 0; O: 1
0
0
0
0
0
SDI/
SPI mode
from USI
1
0
1
0
0
SDO/
SPI mode
from USI
1
0
1
0
0
A7
X
X
X
0
0
1 (y = 7)
TDO/TDI/
TDO/TDI
X
X
X
0
1
0
Pin Osc
Capacitive sensing
X
0
1
0
0
0
7
A7 (2)/
(1)
(2)
40
X = don't care
MSP430G2x32 devices only
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Port P2 Pin Schematic: P2.0 to P2.5, Input/Output With Schmitt Trigger
PxSEL.y
PxDIR.y
0
1
Direction
0: Input
1: Output
PxSEL2.y
PxSEL.y
PxREN.y
0
1
1
0
PxSEL2.y
PxSEL.y
PxOUT.y
1
DVSS
0
DVCC
1
1
0
0
1
0
3
2
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
TAx.y
TAxCLK
PxIN.y
EN
To Module
D
PxIE.y
PxIRQ.y
EN
Q
Set
PxIFG.y
Interrupt
Edge
Select
PxSEL.y
PxIES.y
Table 18. Port P2 (P2.0 to P2.5) Pin Functions
PIN NAME
(P2.x)
P2.0/
Pin Osc
P2.1/
Pin Osc
P2.2/
Pin Osc
P2.3/
Pin Osc
P2.4/
Pin Osc
P2.5/
Pin Osc
(1)
x
0
1
2
3
4
5
FUNCTION
P2.x (I/O)
Capacitive sensing
P2.x (I/O)
Capacitive sensing
P2.x (I/O)
Capacitive sensing
P2.x (I/O)
Capacitive sensing
P2.x (I/O)
Capacitive sensing
P2.x (I/O)
Capacitive sensing
CONTROL BITS / SIGNALS (1)
P2DIR.x
P2SEL.x
P2SEL2.x
I: 0; O: 1
0
0
X
0
1
I: 0; O: 1
0
0
X
0
1
I: 0; O: 1
0
0
X
0
1
I: 0; O: 1
0
0
X
0
1
I: 0; O: 1
0
0
X
0
1
I: 0; O: 1
0
0
X
0
1
X = don't care
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
41
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Port P2 Pin Schematic: P2.6, Input/Output With Schmitt Trigger
XOUT/P2.7
LF off
PxSEL.6 & PxSEL.7
BCSCTL3.LFXT1Sx = 11
0
1
LFXT1CLK
PxSEL.y
PxDIR.y
0
1
Direction
0: Input
1: Output
PxSEL2.y
PxSEL.y
PxREN.y
0
1
1
0
1
PxSEL2.y
PxSEL.y
PxOUT.y
From Module
DVSS
DVCC
0
1
1
0
1
2
0
XIN/P2.6/TA0.1
3
TAx.y
TAxCLK
PxIN.y
EN
To Module
D
PxIE.y
PxIRQ.y
Q
EN
Set
PxIFG.y
PxSEL.y
PxIES.y
Interrupt
Edge
Select
Table 19. Port P2 (P2.6) Pin Functions
PIN NAME
(P2.x)
CONTROL BITS / SIGNALS (1)
x
FUNCTION
XIN/
XIN
P2.6/
P2.x (I/O)
P2DIR.x
P2SEL.6
P2SEL.7
P2SEL2.6
P2SEL2.7
0
1
1
0
0
I: 0; O: 1
0
X
0
0
6
TA0.1/
Timer0_A3.TA1
1
1
0
0
0
Pin Osc
Capacitive sensing
X
0
X
1
X
(1)
42
X = don't care
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
Port P2 Pin Schematic: P2.7, Input/Output With Schmitt Trigger
XIN/P2.6/TA0.1
LF off
PxSEL.6 & PxSEL.7
BCSCTL3.LFXT1Sx = 11
0
1
LFXT1CLK
from P2.6
PxSEL.y
PxDIR.y
0
1
Direction
0: Input
1: Output
PxSEL2.y
PxSEL.y
PxREN.y
0
1
1
0
1
PxSEL2.y
PxSEL.y
PxOUT.y
From Module
DVSS
DVCC
0
1
1
0
1
2
XOUT/P2.7
3
TAx.y
TAxCLK
PxIN.y
EN
To Module
D
PxIE.y
PxIRQ.y
Q
EN
Set
PxIFG.y
Interrupt
Edge
Select
PxSEL.y
PxIES.y
Table 20. Port P2 (P2.7) Pin Functions
PIN NAME
(P2.x)
CONTROL BITS / SIGNALS (1)
x
XOUT/
P2.7/
XOUT
7
Pin Osc
(1)
FUNCTION
P2.x (I/O)
Capacitive sensing
P2DIR.x
P2SEL.6
P2SEL.7
P2SEL2.6
P2SEL2.7
X
1
1
0
0
I: 0; O: 1
0
X
0
0
X
0
X
1
X
X = don't care
Copyright © 2010–2011, Texas Instruments Incorporated
Submit Documentation Feedback
43
MSP430G2x32
MSP430G2x02
SLAS723B – DECEMBER 2010 – REVISED MARCH 2011
www.ti.com
REVISION HISTORY
REVISION
SLAS723
44
DESCRIPTION
Initial release
SLAS723A
Page 1, Changed Internal Frequencies up to 16 MHz With One Calibrated Frequency to Internal Frequencies up
to 16 MHz With Four Calibrated Frequencies
SLAS723B
Added note concerning pulldown resistor to PW14 and RSA16 pinout drawings.
Removed reference to CAOUT from N20, PW20 pinout drawing and Table 11 (there is no comparator module on
this device).
Added "N20, PW20" to Input Pin Number and Output Pin Number columns in Table 11.
Corrected pin numbers for P1.0 to P1.3 for PW14 package in Table 2.
Submit Documentation Feedback
Copyright © 2010–2011, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
26-Mar-2011
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
MSP430G2102IN20
ACTIVE
PDIP
N
20
20
Pb-Free (RoHS)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2102IPW14
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2102IPW14R
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2102IPW20
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2102IPW20R
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2102IRSA16R
ACTIVE
QFN
RSA
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2102IRSA16T
ACTIVE
QFN
RSA
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2132IN20
ACTIVE
PDIP
N
20
20
Pb-Free (RoHS)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2132IPW14
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2132IPW14R
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2132IPW20
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2132IPW20R
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2132IRSA16R
ACTIVE
QFN
RSA
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2132IRSA16T
ACTIVE
QFN
RSA
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2202IN20
ACTIVE
PDIP
N
20
20
Pb-Free (RoHS)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2202IPW14
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2202IPW14R
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2202IPW20
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 1
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
26-Mar-2011
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
MSP430G2202IPW20R
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2202IRSA16R
ACTIVE
QFN
RSA
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2202IRSA16T
ACTIVE
QFN
RSA
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2232IN20
ACTIVE
PDIP
N
20
20
Pb-Free (RoHS)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2232IPW14
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2232IPW14R
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2232IPW20
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2232IPW20R
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2232IRSA16R
ACTIVE
QFN
RSA
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2232IRSA16T
ACTIVE
QFN
RSA
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2302IN20
ACTIVE
PDIP
N
20
20
Pb-Free (RoHS)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2302IPW14
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2302IPW14R
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2302IPW20
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2302IPW20R
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2302IRSA16R
ACTIVE
QFN
RSA
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2302IRSA16T
ACTIVE
QFN
RSA
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2332IN20
ACTIVE
PDIP
N
20
20
Pb-Free (RoHS)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2332IPW14
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Addendum-Page 2
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
26-Mar-2011
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
MSP430G2332IPW14R
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2332IPW20
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2332IPW20R
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2332IRSA16R
ACTIVE
QFN
RSA
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2332IRSA16T
ACTIVE
QFN
RSA
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2402IN20
ACTIVE
PDIP
N
20
20
Pb-Free (RoHS)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2402IPW14
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2402IPW14R
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2402IPW20
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2402IPW20R
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2402IRSA16R
ACTIVE
QFN
RSA
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2402IRSA16T
ACTIVE
QFN
RSA
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2432IN20
ACTIVE
PDIP
N
20
20
Pb-Free (RoHS)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2432IPW14
ACTIVE
TSSOP
PW
14
90
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2432IPW14R
ACTIVE
TSSOP
PW
14
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2432IPW20
ACTIVE
TSSOP
PW
20
70
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2432IPW20R
ACTIVE
TSSOP
PW
20
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
MSP430G2432IRSA16R
ACTIVE
QFN
RSA
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
MSP430G2432IRSA16T
ACTIVE
QFN
RSA
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Addendum-Page 3
Samples
(Requires Login)
PACKAGE OPTION ADDENDUM
www.ti.com
26-Mar-2011
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 4
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
Wireless
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions
www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated