NCP565/NCV565 1.5 A Low Dropout Linear Regulator The NCP565/NCV565 low dropout linear regulator will provide 1.5 A at a fixed output voltage or an adjustable voltage down to 0.9 V. The fast loop response and low dropout voltage make this regulator ideal for applications where low voltage and good load transient response are important. Device protection includes current limit, short circuit protection, and thermal shutdown. Features • • • • • • • • • • • MARKING DIAGRAMS 1 Ultra Fast Transient Response (t1.0 ms) Low Ground Current (1.5 mA at Iload = 1.5 A) Low Dropout Voltage (0.9 V at Iload = 1.5 A) Low Noise (28 mVrms) 0.9 V Reference Voltage Adjustable Output Voltage from 7.7 V down to 0.9 V 1.2 V, 1.5 V, 2.8 V, 3.0 V, 3.3 V Fixed Output Versions. Other Fixed Voltages Available on Request Current Limit Protection (3.3 A Typ) Thermal Shutdown Protection (160°C) NCV Prefix for Automotive and Other Applications Requiring Site and Change Controls Pb−Free Packages are Available Typical Applications • • • • http://onsemi.com 2 D2PAK 3 CASE 936 FIXED 3 NC y565D2Txx AWLYWWG Tab = Ground Pin 1. Vin 2. Ground 3. Vout 1 5 Tab = Ground Pin 1. N.C. 2. Vin 3. Ground 4. Vout 5. Adj Servers ASIC Power Supplies Post Regulation for Power Supplies Constant Current Source NC y565D2T AWLYWWG D2PAK 5 CASE 936A ADJUSTABLE xx y A WL Y WW G = 12 or 33 = P or V = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free P565 MNxx AYWWG G DFN6, 3x3.3 CASE 506AX 1 xx = Voltage Rating AJ = Adjustable 12 = 1.2 V 30 = 3.0V 15 = 1.5 V 33 = 3.3 V 28 = 2.8 V AYW 565yy G G SOT−223 CASE 318E 1 yy A Y W G = Voltage Rating 12 = 1.2 V = Assembly Location = Year = Work Week = Pb−Free Package Tab = Vout Pin 1. Ground 2. Vout 3. Vin (Note: Microdot may be in either location) ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 13 of this data sheet. © Semiconductor Components Industries, LLC, 2010 November, 2010 − Rev. 15 1 Publication Order Number: NCP565/D NCP565/NCV565 Vin Vin Vout Vout Vin Vin NCP565 Vout Vout NCP565 GND GND Cout Cin C1 5.6 pF ADJ R1 Cout Cin R2 Figure 1. Typical Application Schematic, Fixed Output Figure 2. Typical Application Schematic, Adjustable Output PIN DESCRIPTION D2PAK 5 D2PAK 3 Pin No. Adj. Version Pin No. Fixed Version Pin No. Adj. Version 1 − 1, 2 1, 2, 5 − N.C. 2 1 3 3 3 Vin 3, Tab 2, Tab 6 6 1 Ground 4 3 4 4 2, Tab Vout Regulated Output Voltage 5 − 5 − − Adj This pin is to be connected to the sense resistors on the output. The linear regulator will attempt to maintain 0.9 V between this pin and ground. Refer to the Application Information section for output voltage setting. DFN6 SOT−223 Pin No. Pin No. Fixed Version Fixed Version Vin Symbol Description − Positive Power Supply Input Voltage Power Supply Ground Vout Vin Vout Vref = 0.9 V Vref = 0.9 V Output Stage Voltage Reference Block Current Limit Sense Output Stage Voltage Reference Block Current Limit Sense ADJ Thermal Shutdown Block Thermal Shutdown Block GND GND Figure 3. Block Diagram, Fixed Output Figure 4. Block Diagram, Adjustable Output http://onsemi.com 2 NCP565/NCV565 ABSOLUTE MAXIMUM RATINGS Symbol Value Unit Input Voltage (Note 1) Rating Vin 18 V Output Pin Voltage Vout −0.3 to Vin + 0.3 V Adjust Pin Voltage Vadj −0.3 to Vin + 0.3 V Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. NOTE: This device series contains ESD protection and exceeds the following tests: Human Body Model JESD 22−A114−B Machine Model JESD 22−A115−A THERMAL CHARACTERISTICS Rating Symbol Value Unit Thermal Characteristics SOT−223 (Notes 1, 2) Thermal Resistance, Junction−to−Ambient Thermal Resistance, Junction−to−Pin RqJA RqJP 107 12 Thermal Characteristics DFN6 (Notes 1, 2) Thermal Resistance, Junction−to−Ambient Thermal Resistance, Junction−to−Pin RqJA RqJP 176 37 Thermal Characteristics D2PAK (5ld) (Notes 1, 2) Thermal Resistance, Junction−to−Case Thermal Resistance, Junction−to−Ambient Thermal Resistance, Junction−to−Pin RqJC RqJA RqJP 3 105 4 Symbol Value Unit Operating Input Voltage (Note 1) Vin Vout + VDO, 2.5 (Note 3) to 9 V Operating Junction Temperature Range TJ −40 to 150 °C Operating Ambient Temperature Range TA −40 to 125 °C Storage Temperature Range Tstg −55 to 150 °C °C/W °C/W °C/W OPERATING RANGES Rating 1. Refer to Electrical Characteristics and Application Information for Safe Operating Area. 2. As measured using a copper heat spreading area of 50 mm2, 1 oz copper thickness. 3. Minimum Vin = (Vout + VDO) or 2.5 V, whichever is higher. http://onsemi.com 3 NCP565/NCV565 ELECTRICAL CHARACTERISTICS (Vin = Vout + 1.6 V, Vout = 0.9 V, TA= 25°C, Cin = Cout = 150 mF, unless otherwise noted, Note 4.) Characteristic Symbol Min Typ Max Unit Reference Voltage (10 mA < Iout < 1.5 A; Vout + 1.6 V < Vin < 9.0 V; TA = −10 to 105°C) Vref 0.882 (−2%) 0.9 0.918 (+2%) V Reference Voltage (10 mA < Iout < 1.5 A; Vout + 1.6 V < Vin < 9.0 V; TA = −40 to 125°C) Vref 0.873 (−3%) 0.9 0.927 (+3%) V ADJ Pin Current (Note 5) IAdj − 30 − nA Line Regulation (Iout = 10 mA) (Note 5) Regline − 0.03 − % Load Regulation (10 mA < Iout < 1.5 A) (Note 5) Regload − 0.03 − % ADJUSTABLE OUTPUT VERSION Dropout Voltage (Iout = 1.5 A, Vout = 2.5 V) (Note 6) Vdo − 0.9 1.3 V Current Limit Ilim 1.6 3.3 − A Ripple Rejection (120 Hz; Iout = 1.5 A) (Note 5) RR − 85 − dB Ripple Rejection (1 kHz; Iout = 1.5 A) (Note 5) Ground Current (Iout = 1.5 A) Output Noise Voltage (f = 100 Hz to 100 kHz, Iout = 1.5 A) (Note 5) Thermal Shutdown Protection (Note 5) RR − 75 − dB IGND − 1.5 3.0 mA Vn − 28 − mVrms TSHD − 160 − _C FIXED OUTPUT VOLTAGE (Vin = Vout + 1.6 V, TA = 25°C, Cin = Cout = 150 mF, unless otherwise noted, Note 4.) Output Voltage (10 mA < Iout < 1.5 A; 2.8 V < Vin < 9.0 V; TA = −10 to 105°C) 1.2 V version Vout 1.176 (−2%) 1.2 1.224 (+2%) V Output Voltage (10 mA < Iout < 1.5 A; 2.8 V < Vin < 9.0 V; TA = −40 to 125°C) 1.2 V version Vout 1.164 (−3%) 1.2 1.236 (+3%) V Output Voltage (10 mA < Iout < 1.5 A; 3.1 V < Vin < 9.0 V; TA = −10 to 105°C) 1.5 V version Vout 1.470 (−2%) 1.5 1.530 (+2%) V Output Voltage (10 mA < Iout < 1.5 A; 3.1 V < Vin < 9.0 V; TA = −40 to 125°C) 1.5 V version Vout 1.455 (−3%) 1.5 1.545 (+3%) V Output Voltage (10 mA < Iout < 1.5 A; 4.4 V < Vin < 9.0 V; TA = −10 to 105°C) 2.8 V version Vout 2.744 (−2%) 2.8 2.856 (+2%) V Output Voltage (10 mA < Iout < 1.5 A; 4.4 V < Vin < 9.0 V; TA = −40 to 125°C) 2.8 V version Vout 2.716 (−3%) 2.8 2.884 (+3%) V Output Voltage (10 mA < Iout < 1.5 A; 4.6 V < Vin < 9.0 V; TA = −10 to 105°C) 3.0 V version Vout 2.940 (−2%) 3.0 3.060 (+2%) V Output Voltage (10 mA < Iout < 1.5 A; 4.6 V < Vin < 9.0 V; TA = −40 to 125°C) 3.0 V version Vout 2.910 (−3%) 3.0 3.090 (+3%) V Output Voltage (10 mA < Iout < 1.5 A; 4.9 V < Vin < 9.0 V; TA = −10 to 105°C) 3.3 V version Vout 3.234 (−2%) 3.3 3.366 (+2%) V Output Voltage (10 mA < Iout < 1.5 A; 4.9 V < Vin < 9.0 V; TA = −40 to 125°C) 3.3 V version Vout 3.201 (−3%) 3.3 3.399 (+3%) V Line Regulation (Iout = 10 mA) (Note 5) Regline − 0.03 − % Load Regulation (10 mA < Iout < 1.5 A) (Note 5) Regload − 0.03 − % Vdo − 0.9 1.3 V Current Limit Ilim 1.6 3.3 − A Ripple Rejection (120 Hz; Iout = 1.5 A) (Note 5) RR − 85 − dB Ripple Rejection (1 kHz; Iout = 1.5 A) (Note 5) RR − 75 − dB IGND − 1.5 3.0 mA Vn − 38 − mVrms TSHD − 160 − _C Dropout Voltage (Iout = 1.5 A, Vout = 2.5 V) (Note 6) Ground Current (Iout = 1.5 A) Output Noise Voltage (f = 100 Hz to 100 kHz, Vout = 1.2 V, Iout = 1.5 A) (Note 5) Thermal Shutdown Protection (Note 5) 4. Performance guaranteed over specified operating conditions by design, guard banded test limits, and/or characterization, production tested at TJ = TA = 25_C. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. 5. Typical values are based on design and/or characterization. 6. Dropout voltage is a measurement of the minimum input/output differential at full load. http://onsemi.com 4 NCP565/NCV565 TYPICAL CHARACTERISTICS 3.302 Vref, REFERENCE VOLTAGE (V) Vref, REFERENCE VOLTAGE (V) 0.9005 0.9000 0.8995 0.8990 0.8985 0.8980 Vin = 2.5 V Vout(nom) = 0.9 V 0.8975 0.8970 −50 0 −25 25 50 75 100 125 3.300 3.298 3.296 3.294 3.292 Vin = 4.9 V Vout(nom) = 3.3 V 3.290 3.288 −50 150 75 100 150 125 1.2 Vin − Vout, DROPOUT VOLTAGE (V) ISC, SHORT CIRCUIT CURRENT LIMIT (A) 3.80 3.70 3.60 3.50 3.40 3.30 3.20 3.10 −25 0 25 50 75 100 125 1.0 0.6 Iout = 50 mA 0.4 0.2 0 −50 150 Iout = 1.5 A 0.8 TJ, JUNCTION TEMPERATURE (°C) −25 0 25 50 75 100 125 150 TJ, JUNCTION TEMPERATURE (°C) Figure 7. Short Circuit Current Limit vs. Temperature Figure 8. Dropout Voltage vs. Temperature 1.80 IGND, GROUND CURRENT (mA) 1.60 IGND, GROUND CURRENT (mA) 50 Figure 6. Output Voltage vs. Temperature Figure 5. Output Voltage vs. Temperature 1.55 1.50 Iout = 1.5 A 1.45 1.40 1.35 1.30 −50 25 TJ, JUNCTION TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C) 3.00 −50 0 −25 −25 25 75 125 0 50 100 TJ, JUNCTION TEMPERATURE (°C) 150 1.70 1.65 1.60 1.55 1.50 1.45 1.40 1.35 0 300 600 900 1200 1500 Iout, OUTPUT CURRENT (mA) Figure 9. Ground Current vs. Temperature Figure 10. Ground Current vs. Output Current http://onsemi.com 5 NCP565/NCV565 TYPICAL CHARACTERISTICS 100 1000 80 Unstable 70 100 60 ESR (W) RIPPLE REJECTION (dB) 90 50 40 10 Iout = 1.5 A 30 20 0 10 100 1000 10000 1 100000 1000000 0 250 OUTPUT VOLTAGE DEVIATION (mV) 10 0 −10 Vin = 4.59 V Vout = 0.9 V −30 −40 1.50 1.00 0.50 0 0 50 100 150 200 250 500 750 300 350 0 Vin = 4.59 V Vout = 0.9 V −20 −30 −40 1.50 1.00 0.50 0 400 0 0.5 1.0 1.5 OUTPUT VOLTAGE DEVIATION (mV) 10 0 1.50 Iout, OUTPUT CURRENT (A) OUTPUT VOLTAGE DEVIATION (mV) Iout, OUTPUT CURRENT (A) Vin = 4.59 V Vout = 0.9 V 1.00 0.50 0 100 150 200 2.5 3.0 3.5 4.0 Figure 14. Load Transient from 10 mA to 1.5 A 40 50 2.0 TIME (ms) 50 −50 0 1500 −10 Figure 13. Load Transient from 10 mA to 1.5 A 20 1250 10 TIME (nS) 30 1000 Figure 12. Output Capacitor ESR Stability vs. Output Current Iout, OUTPUT CURRENT (A) OUTPUT VOLTAGE DEVIATION (mV) Figure 11. Ripple Rejection vs. Frequency −20 Cout = 10 mF OUTPUT CURRENT (mA) F, FREQUENCY (Hz) Iout, OUTPUT CURRENT (A) Vout = 3.3 V Stable 10 250 300 350 50 40 30 Vin = 4.59 V Vout = 0.9 V 20 10 0 1.50 1.00 0.50 400 TIME (nS) 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 TIME (ms) Figure 16. Load Transient from 1.5 A to 10 mA Figure 15. Load Transient from 1.5 A to 10 mA http://onsemi.com 6 NCP565/NCV565 100 100 90 90 NOISE DENSITY (nVrms/ǰHz) NOISE DENSITY (nVrms/ǰHz) TYPICAL CHARACTERISTICS 80 70 60 Vin = 3.0 V Vout = 0.9 V Iout = 10 mA 50 40 30 20 10 0 Start 1.0 kHz FREQUENCY (kHz) 80 70 Vin = 3.0 V Vout = 0.9 V Iout = 1.5 A 60 50 40 30 20 10 0 Start 1.0 kHz Stop 100 kHz Figure 17. Noise Density vs. Frequency FREQUENCY (kHz) Stop 100 kHz Figure 18. Noise Density vs. Frequency NOTE: Typical characteristics were measured with the same conditions as electrical characteristics. http://onsemi.com 7 NCP565/NCV565 APPLICATION INFORMATION Adjustable Operation The typical application circuit for the adjustable output regulators is shown in Figure 2. The adjustable device develops and maintains the nominal 0.9 V reference voltage between Adj and ground pins. A resistor divider network R1 and R2 causes a fixed current to flow to ground. This current creates a voltage across R1 that adds to the 0.9 V across R2 and sets the overall output voltage. The output voltage is set according to the formula: The NCP565 low dropout linear regulator provides adjustable voltages at currents up to 1.5 A. It features ultra fast transient response and low dropout voltage. These devices contain output current limiting, short circuit protection and thermal shutdown protection. Input, Output Capacitor and Stability An input bypass capacitor is recommended to improve transient response or if the regulator is located more than a few inches from the power source. This will reduce the circuit’s sensitivity to the input line impedance at high frequencies and significantly enhance the output transient response. Different types and different sizes of input capacitors can be chosen dependent on the quality of power supply. A 150 mF OSCON 16SA150M type from Sanyo should be adequate for most applications. The bypass capacitor should be mounted with shortest possible lead or track length directly across the regulator’s input terminals. The output capacitor is required for stability. The NCP565 remains stable with ceramic, tantalum, and aluminum− electrolytic capacitors with a minimum value of 1.0 mF with ESR between 50 mW and 2.5 W. The NCP565 is optimized for use with a 150 mF OSCON 16SA150M type in parallel with a 10 mF OSCON 10SL10M type from Sanyo. The 10 mF capacitor is used for best AC stability while 150 mF capacitor is used for achieving excellent output transient response. The output capacitors should be placed as close as possible to the output pin of the device. If not, the excellent load transient response of NCP565 will be degraded. Vout + Vref Load Transient Measurement Large load current changes are always presented in microprocessor applications. Therefore good load transient performance is required for the power stage. NCP565 has the feature of ultra fast transient response. Its load transient responses in Figures 13 through 16 are tested on evaluation board shown in Figure 19. On the evaluation board, it consists of NCP565 regulator circuit with decoupling and filter capacitors and the pulse controlled current sink to obtain load current transitions. The load current transitions are measured by current probe. Because the signal from current probe has some time delay, it causes un−synchronization between the load current transition and output voltage response, which is shown in Figures 13 through 16. Vout −VCC Pulse + R2 The adjust pin current, IAdj, is typically 30 nA and normally much lower than the current flowing through R1 and R2, thus it generates a small output voltage error that can usually be ignored. GEN Vin ) R2Ǔ * I ǒR1 R2 Adj V NCP565 Evaluation Board RL GND + GND Scope Voltage Probe Figure 19. Schematic for Transient Response Measurement http://onsemi.com 8 NCP565/NCV565 PCB Layout Considerations several capacitors in parallel. This reduces the overall ESR and reduces the instantaneous output voltage drop under transient load conditions. The output capacitor network should be as close as possible to the load for the best results. The schematic of NCP565 typical application circuit, which this PCB layout is base on, is shown in Figure 20. The output voltage is set to 3.3 V for this demonstration board according to the feedback resistors in the Table 1. Good PCB layout plays an important role in achieving good load transient performance. Because it is very sensitive to its PCB layout, particular care has to be taken when tackling Printed Circuit Board (PCB) layout. The figures below give an example of a layout where parasitic elements are minimized. For microprocessor applications it is customary to use an output capacitor network consisting of 2 Vin C1 150 m C2 150 m 1 Vin Vout Vout 4 NCP565 Adj NC 5 C4 10 m GND C3 150 m 3 C3 150 m GND GND R2 R1 15.8 k 42.2 k C6 5.6 p Figure 20. Schematic of NCP565 Typical Application Circuit Figure 21. Top Layer http://onsemi.com 9 NCP565/NCV565 Figure 22. Bottom Layer NCP565 ON Semiconductor www.onsemi.com D1 VIN R2 C2 VOUT C3 C4 C1 R1C6 C5 GND GND July, 2003 Figure 23. Silkscreen Layer http://onsemi.com 10 NCP565/NCV565 Table 1. Bill of Materials for NCP565 Adj Demonstration Board Item Used # Component Designators Suppliers Part Number 1 4 Radial Lead Aluminum Capacitor 150 mF/16 V C1, C2, C3, C5 Sanyo Oscon 16SA150M 2 1 Radial Lead Aluminum Capacitor 10 mF/10 V C4 Sanyo Oscon 10SL10M 3 1 SMT Chip Resistor (0805) 15.8 K 1% R2 Vishay CRCW08051582F 4 1 SMT Chip Resistor (0805) 42.2 K 1% R1 Vishay CRCW08054222F 5 1 SMT Ceramic Capacitor (0603) 5.6 pF 10% C6 Vishay VJ0603A5R6KXAA 6 1 NCP565 Low Dropout Linear Regulator U1 ON Semiconductor NCP565D2TR4 http://onsemi.com 11 NCP565/NCV565 Protection Diodes Thermal Considerations When large external capacitors are used with a linear regulator it is sometimes necessary to add protection diodes. If the input voltage of the regulator gets shorted, the output capacitor will discharge into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage and the rate at which Vin drops. In the NCP565 linear regulator, the discharge path is through a large junction and protection diodes are not usually needed. If the regulator is used with large values of output capacitance and the input voltage is instantaneously shorted to ground, damage can occur. In this case, a diode connected as shown in Figure 24 is recommended. This series contains an internal thermal limiting circuit that is designed to protect the regulator in the event that the maximum junction temperature is exceeded. This feature provides protection from a catastrophic device failure due to accidental overheating. It is not intended to be used as a substitute for proper heat sinking. The maximum device power dissipation can be calculated by: PD + TJ(max) * TA RqJA 200 180 160 1N4002 (Optional) Vin C1 Vout NCP565 GND Vout Adj CAdj R1 qJA (°C/W) Vin C2 140 DFN 1 oz Cu DFN 2 oz Cu SOT−223 1 oz Cu 120 SOT−223 2 oz Cu D2PAK 1 oz Cu 100 D2PAK 2 oz Cu 80 R2 60 40 0 Figure 24. Protection Diode for Large Output Capacitors 50 100 150 200 250 300 350 400 450 500 COPPER HEAT−SPREADER AREA (mm sq) Figure 25. Thermal Resistance http://onsemi.com 12 NCP565/NCV565 ORDERING INFORMATION Device Nominal Output Voltage** Package NCP565D2T D2PAK NCP565D2TG D2PAK NCP565D2TR4 5 5 (Pb−Free) 50 Units / Tube D2PAK 5 Adj NCP565D2TR4G D2PAK 5 (Pb−Free) NCP565MNADJT2G DFN6 (Pb−Free) NCP565D2T12 D2PAK 3 NCP565D2T12G D2PAK 3 (Pb−Free) NCP565D2T12R4 D2PAK 3 NCP565D2T12R4G Shipping† D2PAK 3 (Pb−Free) Fixed (1.2 V) 800 / Tape & Reel 3000 / Tape & Reel 50 Units / Tube 800 / Tape & Reel NCP565MN12T2G DFN6 (Pb−Free) 3000 / Tape & Reel NCP565ST12T3G SOT−223 (Pb−Free) 4000 / Tape & Reel Fixed (1.5 V) DFN6 (Pb−Free) 3000 / Tape & Reel Fixed (2.8 V) DFN6 (Pb−Free) 3000 / Tape & Reel Fixed (3.0 V) DFN6 (Pb−Free) 3000 / Tape & Reel D2PAK 3 (Pb−Free) 50 Units / Tube D2PAK 3 (Pb−Free) 800 / Tape & Reel DFN6 (Pb−Free) 3000 / Tape & Reel NCP565MN15T2G NCP565MN28T2G NCP565MN30T2G NCP565D2T33G NCP565D2T33R4G Fixed (3.3 V) NCP565MN33T2G NCV565D2TG* NCV565D2TR4G* D2PAK 5 (Pb−Free) Adj NCV565D2T12R4G* NCV565ST12T3G* Fixed (1.2 V) 50 Units / Tube 800 / Tape & Reel D2PAK 3 (Pb−Free) 800 / Tape & Reel SOT−223 (Pb−Free) 4000 / Tape & Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV prefix is for automotive and other applications requiring site and change controls. **For other fixed output versions, please contact the factory. The max Vout available for SOT−223 is 1.2 V. http://onsemi.com 13 NCP565/NCV565 PACKAGE DIMENSIONS D2PAK 3 D2T SUFFIX CASE 936−03 ISSUE C −T− K OPTIONAL CHAMFER A TERMINAL 4 E U S B F V H 1 2 3 M J D 0.010 (0.254) M T C G NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. L P N R SOLDERING FOOTPRINT* 10.49 8.38 16.155 2X 3.504 2X 1.016 5.080 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 14 DIM A B C D E F G H J K L M N P R S U V INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.051 REF 0.100 BSC 0.539 0.579 0.125 MAX 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.295 REF 2.540 BSC 13.691 14.707 3.175 MAX 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN NCP565/NCV565 PACKAGE DIMENSIONS D2PAK 5 CASE 936A−02 ISSUE C TERMINAL 6 −T− OPTIONAL CHAMFER A U U1 E S K B V V1 H NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 6. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. 1 2 3 4 5 M D 0.010 (0.254) G M N T DIM A B C D E G H K L M N P R S U V U1 V1 L P R C SOLDERING FOOTPRINT* 8.38 0.33 1.702 0.067 10.66 0.42 16.02 0.63 1.016 0.04 3.05 0.12 SCALE 3:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 15 INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.067 BSC 0.539 0.579 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 _ REF 0.116 REF 0.200 MIN 0.250 MIN 0.297 0.305 0.038 0.046 MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.702 BSC 13.691 14.707 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 _ REF 2.946 REF 5.080 MIN 6.350 MIN 7.544 7.747 0.965 1.168 NCP565/NCV565 PACKAGE DIMENSIONS SOT−223 (TO−261) CASE 318E−04 ISSUE N D b1 NOTES: 6. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 7. CONTROLLING DIMENSION: INCH. 4 HE 1 2 3 b e1 e A1 C q A 0.08 (0003) DIM A A1 b b1 c D E e e1 L L1 HE E q L L1 SOLDERING FOOTPRINT 3.8 0.15 2.0 0.079 2.3 0.091 2.3 0.091 6.3 0.248 2.0 0.079 1.5 0.059 SCALE 6:1 http://onsemi.com 16 mm Ǔ ǒinches MIN 1.50 0.02 0.60 2.90 0.24 6.30 3.30 2.20 0.85 0.20 1.50 6.70 0° MILLIMETERS NOM MAX 1.63 1.75 0.06 0.10 0.75 0.89 3.06 3.20 0.29 0.35 6.50 6.70 3.50 3.70 2.30 2.40 0.94 1.05 −−− −−− 1.75 2.00 7.00 7.30 10° − MIN 0.060 0.001 0.024 0.115 0.009 0.249 0.130 0.087 0.033 0.008 0.060 0.264 0° INCHES NOM 0.064 0.002 0.030 0.121 0.012 0.256 0.138 0.091 0.037 −−− 0.069 0.276 − MAX 0.068 0.004 0.035 0.126 0.014 0.263 0.145 0.094 0.041 −−− 0.078 0.287 10° NCP565/NCV565 PACKAGE DIMENSIONS DFN6, 3x3.3, 0.95 PITCH CASE 506AX−01 ISSUE O A D PIN 1 REFERENCE ÇÇÇÇ ÇÇÇÇ ÇÇÇÇ 2X NOTES: 1. DIMENSIONS AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 mm FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. B E DIM A A1 A3 b D D2 E E2 e K L L1 0.15 C 2X 0.15 C TOP VIEW 0.10 C A 6X 0.08 C (A3) SIDE VIEW A1 D2 6X C SEATING PLANE SOLDERING FOOTPRINT* 4X 3.60 e L 1 K 3 MILLIMETERS MIN NOM MAX 0.80 −−− 0.90 0.00 −−− 0.05 0.20 REF 0.30 −−− 0.40 3.00 BSC 1.90 −−− 2.10 3.30 BSC 1.10 −−− 1.30 0.95 BSC 0.20 −−− −−− 0.40 −−− 0.60 0.00 −−− 0.15 1.35 6X 0.50 1 E2 6X L1 2.15 6 0.95 PITCH 4 6X BOTTOM VIEW b (NOTE 3) 0.10 C A B 6X 0.83 0.05 C DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. The product described herein (NCP565), may be covered by one or more of the following U.S. patents: 5,920,184; 5,834,926. There may be other patents pending. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 17 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NCP565/D