IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S Document Title 256Kx16 bit Dynamic RAM with Fast Page Mode Revision History Revision No History Draft Date 0A Initial Draft August 11,2001 Remark The attached datasheets are provided by ICSI. Integrated Circuit Solution Inc reserve the right to change the specifications and products. ICSI will answer to your questions about device. If you have any questions, please contact the ICSI offices. Integrated Circuit Solution Inc. DR021-0A 08/11/2001 1 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S 256K x 16 (4-MBIT) DYNAMIC RAM WITH FAST PAGE MODE FEATURES • • • • • • • • • DESCRIPTION The ICSI IC41C16257 and the IC41LV16257 are 262,144 Fast access and cycle time x 16-bit high-performance CMOS Dynamic Random Access TTL compatible inputs and outputs Memory. Fast Page Mode allows 512 random accesses Refresh Interval: 512 cycles/8 ms within a single row with access cycle time as short as 12 ns per 16-bit word. The Byte Write control, of upper and lower Refresh Mode: RAS-Only, CAS-before-RAS byte, makes these devices ideal for use in 16-, 32-bit wide (CBR), Hidden data bus systems. Self Refresh Mode: 512 cycles/64 ms (S version These features make the IC41C16257 and the IC41LV16257 only) ideally suited for high band-width graphics, digital signal JEDEC standard pinout processing, high-performance computing systems, and peripheral applications. Single power supply: — 5V ± 10% (IC41C16257) The IC41C16257 and the IC41LV16257 are packaged in a 40-pin, 400mil SOJ and TSOP-2. — 3.3V ± 10% (IC41LV16257) Byte Write and Byte Read operation via KEY TIMING PARAMETERS two CAS Parameter -35 -50 -60 Unit Available in 40-pin SOJ and TSOP-2 PIN CONFIGURATIONS 40-Pin TSOP-2 Max. RAS Access Time (tRAC) Max. CAS Access Time (tCAC) Max. Column Address Access Time (tAA) Min. Fast Page Mode Cycle Time (tPC) 35 10 18 12 50 14 25 20 60 15 30 25 ns ns ns ns Min. Read/Write Cycle Time (tRC) 60 90 110 ns 40-Pin SOJ PIN DESCRIPTIONS A0-A8 Address Inputs I/O0-I/O15 Data Inputs/Outputs WE Write Enable OE Output Enable RAS Row Address Strobe UCAS Upper Column Address Strobe LCAS Lower Column Address Strobe Vcc Power GND Ground NC No Connection ICSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which may appear in this publication. © Copyright 2000, Integrated Circuit Solution Inc. 2 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S FUNCTIONAL BLOCK DIAGRAM Integrated Circuit Solution Inc. DR021-0A 08/11/2001 3 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S TRUTH TABLE Function Standby Read: Word Read: Lower Byte RAS H L L Read: Upper Byte L H Write: Word (Early Write) Write: Lower Byte (Early Write) L L Write: Upper Byte (Early Write) L Read-Write(1,2) Hidden Refresh2) RAS-Only Refresh CBR Refresh(3) L Read L→H→L Write L→H→L L H→L LCAS UCAS H H L L L H WE X H H OE X L L Address tR/tC X ROW/COL ROW/COL L H L ROW/COL L L L H L L X X ROW/COL ROW/COL H L L X ROW/COL L L L H L L L L H L H→L H L X X L→H L X X X ROW/COL ROW/COL ROW/COL ROW/NA X I/O High-Z DOUT Lower Byte, DOUT Upper Byte, High-Z Lower Byte, High-Z Upper Byte, DOUT DIN Lower Byte, DIN Upper Byte, High-Z Lower Byte, High-Z Upper Byte, DIN DOUT, DIN DOUT DOUT High-Z High-Z Notes: 1. These WRITE cycles may also be BYTE WRITE cycles (either LCAS or UCAS active). 2. These READ cycles may also be BYTE READ cycles (either LCAS or UCAS active). 3. At least one of the two CAS signals must be active (LCAS or UCAS). 4 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S FUNCTIONAL DESCRIPTION The IC41C16257 and the IC41LV16257 are CMOS DRAMs optimized for high-speed bandwidth, low-power applications. During READ or WRITE cycles, each bit is uniquely addressed through the 18 address bits. These are entered nine bits (A0-A8) at a time. The row address is latched by the Row Address Strobe (RAS). The column address is latched by the Column Address Strobe (CAS). RAS is used to latch the first nine bits and CAS is used to latch the latter nine bits. The IC41C16257 and the IC41LV16257 have two CAS controls, LCAS and UCAS. The LCAS and UCAS inputs internally generate a CAS signal functioning in an identical manner to the single CAS input on the other 256K x 16 DRAMs. The key difference is that each CAS controls its corresponding I/O tristate logic (in conjunction with OE and WE and RAS). LCAS controls I/O0 - I/O7 and UCAS controls I/O8 - I/O15. The IC41C16257/IC41LV16257 CAS function is determined by the first CAS (LCAS or UCAS) transitioning LOW and the last transitioning back HIGH. The two CAS controls give the IC41C16257 both BYTE READ and BYTE WRITE cycle capabilities. Memory Cycle A memory cycle is initiated by bringing RAS LOW and it is terminated by returning both RAS and CAS HIGH. To ensure proper device operation and data integrity any memory cycle, once initiated, must not be ended or aborted before the minimum tRAS time has expired. A new cycle must not be initiated until the minimum precharge time tRP, tCP has elapsed. Read Cycle A read cycle is initiated by the falling edge of CAS or OE, whichever occurs last, while holding WE HIGH. The column address must be held for a minimum time specified by tAR. Data Out becomes valid only when tRAC, tAA, tCAC and tOE are all satisfied. As a result, the access time is dependent on the timing relationships between these parameters. Write Cycle A write cycle is initiated by the falling edge of CAS and WE, whichever occurs last. The input data must be valid at or before the falling edge of CAS or WE, whichever occurs last. Refresh Cycle To retain data, 512 refresh cycles are required in each 8 ms period. There are two ways to refresh the memory: 1. By clocking each of the 512 row addresses (A0 through A8) with RAS at least once every 8 ms. Any read, write, read-modify-write or RAS-only cycle refreshes the addressed row. 2. Using a CAS-before-RAS refresh cycle. CAS-beforeRAS refresh is activated by the falling edge of RAS, while holding CAS LOW. In CAS-before-RAS refresh cycle, an internal 9-bit counter provides the row addresses and the external address inputs are ignored. CAS-before-RAS is a refresh-only mode and no data access or device selection is allowed. Thus, the output remains in the High-Z state during the cycle. Self Refresh Cycle(1) The Self Refresh allows the user a dynamic refresh, data retention mode at the extended refresh period of 64 ms. i.e., 125 µs per row when using distributed CBR refreshes. The feature also allows the user the choice of a fully static, low power data retention mode. The optional Self Refresh feature is initiated by performing a CBR Refresh cycle and holding RAS LOW for the specified tRASS. The Self Refresh mode is terminated by driving RAS HIGH for a minimum time of tRPS. This delay allows for the completion of any internal refresh cycles that may be in process at the time of the RAS LOW-to-HIGH transition. If the DRAM controller uses a distributed refresh sequence, a burst refresh is not required upon exiting Self Refresh. However, if the DRAM controller utilizes a RAS-only or burst refresh sequence, all 512 rows must be refreshed within the average internal refresh rate, prior to the resumption of normal operation. Power-On After application of the V CC supply, an initial pause of 200 µs is required followed by a minimum of eight initialization cycles (any combination of cycles containing a RAS signal). During power-on, it is recommended that RAS track with VCC or be held at a valid VIH to avoid current surges. Note: 1.Self Refresh is for Sversion only. Integrated Circuit Solution Inc. DR021-0A 08/11/2001 5 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S ABSOLUTE MAXIMUM RATINGS(1) Symbol Parameters VT Voltage on Any Pin Relative to GND VCC Supply Voltage IOUT PD TA Output Current Power DICSIpation Operation Temperature TSTG Storage Temperature 5V 3.3V 5V 3.3V Com. Ind. Rating Unit –1.0 to +7.0 –0.5 to +4.6 –1.0 to +7.0 –0.5 to +4.6 50 1 0 to +70 -40 to +85 –55 to +125 V V V V mA W o C o C o C Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. RECOMMENDED OPERATING CONDITIONS (Voltages are referenced to GND) Symbol Parameter VCC Supply Voltage VIH Input High Voltage VIL Input Low Voltage TA Ambient Temperature 5V 3.3V 5V 3.3V 5V 3.3V Com. Ind. Min. Typ. Max. Unit 4.5 3.0 2.4 2.0 –1.0 –0.3 0 –40 5.0 3.3 — — — — — — 5.5 3.6 VCC + 1.0 VCC + 0.3 0.8 0.8 70 85 V V V V V V o C o C CAPACITANCE(1,2) Symbol Parameter CIN1 CIN2 CIO Input Capacitance: A0-A8 Input Capacitance: RAS, UCAS, LCAS, WE, OE Data Input/Output Capacitance: I/O0-I/O15 Max. Unit 5 7 7 pF pF pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25oC, f = 1 MHz, VCC = 5.0V + 10%, or VCC = 3.3V + 10%. 6 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S ELECTRICAL CHARACTERISTICS(1) (Recommended Operation Conditions unless otherwise noted.) Symbol Parameter Test Condition IIL Input Leakage Current IIO Output Leakage Current VOH VOL Output High Voltage Level Output Low Voltage Level Any input 0V ≤ VIN ≤ Vcc Other inputs not under test = 0V Output is disabled (Hi-Z) 0V ≤ VOUT ≤ Vcc IOH = –2.5 mA IOL = +2.1 mA ICC1 Stand-by Current: TTL RAS, LCAS, UCAS ≥ VIH ICC1 ICC2 ICC2 ICC3 ICC4 ICC5 ICC6 ICCS Min. Max. Unit –10 10 µA –10 10 µA 2.4 — — 0.4 V V Com. 5V Ind. 5V Stand-by Current: TTL RAS, LCAS, UCAS ≥ VIH Com. 3.3V Ind. 3.3V Stand-by Current: CMOS RAS, LCAS, UCAS ≥ VCC – 0.2V 5V Stand-by Current: CMOS RAS, LCAS, UCAS ≥ VCC – 0.2V 3.3V Operating Current: RAS, LCAS, UCAS, -35 Random Read/Write(2,3,4) Address Cycling, tRC = tRC (min.) -50 Average Power Supply Current -60 Operating Current: RAS = VIL, LCAS, UCAS, -35 Fast Page Mode(2,3,4) Cycling tPC = tPC (min.) -50 Average Power Supply Current -60 Refresh Current: RAS Cycling, LCAS, UCAS ≥ VIH -35 RAS-Only(2,3) tRC = tRC (min.) -50 Average Power Supply Current -60 Refresh Current: RAS, LCAS, UCAS Cycling -35 CBR(2,3,5) tRC = tRC (min.) -50 Average Power Supply Current -60 — — — — — — — — — — — — — — — — — — 2 3 1 2 1 0.5 230 180 170 220 170 160 230 180 170 230 180 170 mA mA mA mA mA mA mA Self Refresh current(6) — — 300 300 Self Refresh Mode Speed 5V 3.3V mA mA mA µA µA Notes: 1. An initial pause of 200 µs is required after power-up followed by eight RAS refresh cycles (RAS-Only or CBR) before proper device operation is assured.The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. Dependent on cycle rates. 3. Specified values are obtained with minimum cycle time and the output open. 4. Column-address is changed once each fast page cycle. 5. Enables on-chip refresh and address counters. 6. ICCS is for S version only. Integrated Circuit Solution Inc. DR021-0A 08/11/2001 7 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S AC CHARACTERISTICS(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) Symbol Parameter tRC tRAC tCAC tAA tRAS tRP tCAS tCP tCSH tRCD tASR tRAH tASC tCAH tAR Random READ or WRITE Cycle Time Access Time from RAS(6, 7) Access Time from CAS(6, 8, 15) Access Time from Column-Address(6) RAS Pulse Width RAS Precharge Time CAS Pulse Width(26) CAS Precharge Time(9, 25) CAS Hold Time (21) RAS to CAS Delay Time(10, 20) Row-Address Setup Time Row-Address Hold Time Column-Address Setup Time(20) Column-Address Hold Time(20) Column-Address Hold Time (referenced to RAS) RAS to Column-Address Delay Time(11) Column-Address to RAS Lead Time RAS to CAS Precharge Time RAS Hold Time(27) CAS to Output in Low-Z(15, 29) CAS to RAS Precharge Time(21) Output Disable Time(19, 28, 29) Output Enable Time(15, 16) OE LOW to CAS HIGH Setup Time Read Command Setup Time(17, 20) Read Command Hold Time (referenced to RAS)(12) Read Command Hold Time (referenced to CAS)(12, 17, 21) Write Command Hold Time(17, 27) Write Command Hold Time (referenced to RAS)(17) Write Command Pulse Width(17) Write Command to RAS Lead Time(17) Write Command to CAS Lead Time(17, 21) Write Command Setup Time(14, 17, 20) Data-in Hold Time (referenced to RAS) tRAD tRAL tRPC tRSH tCLZ tCRP tOD tOE tOES tRCS tRRH tRCH tWCH tWCR tWP tRWL tCWL tWCS tDHR -35 Min. Max. -50 Min. Max. -60 Min. Max. Units 60 — — — 35 20 6 5 35 11 0 6 0 6 30 — 35 10 18 10K — 10K — — 28 — — — — — 90 — — — 50 30 8 8 50 19 0 8 0 8 40 — 50 14 25 10K — 10K — — 36 — — — — — 110 — — — 60 40 10 10 60 20 0 10 0 10 40 — 60 15 30 10K — 10K — — 45 — — — — — ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 12 18 0 8 3 5 3 — 5 0 0 20 — — — — — 15 10 — — — 14 25 0 14 3 5 3 — 5 0 0 25 — — — — — 15 15 — — — 15 30 0 15 3 5 3 — 5 0 0 30 — — — — — 15 15 — — — ns ns ns ns ns ns ns ns ns ns ns 0 — 0 — 0 — ns 5 30 — — 8 40 — — 10 50 — — ns ns 5 8 8 0 30 — — — — — 8 14 14 0 40 — — — — — 10 15 15 0 45 — — — — — ns ns ns ns ns (Continued) 8 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S AC CHARACTERISTICS(1,2,3,4,5,6) (Recommended Operating Conditions unless otherwise noted.) -35 Min. Max. Symbol Parameter tACH tOEH tDS tDH tRWC tRWD tCWD tAWD tPC tRASP tCPA tPRWC tOFF tCLCH tCSR tCHR tORD tREF tT Column-Address Setup Time to CAS Precharge during WRITE Cycle OE Hold Time from WE during READ-MODIFY-WRITE cycle(18) Data-In Setup Time(15, 22) Data-In Hold Time(15, 22) READ-MODIFY-WRITE Cycle Time RAS to WE Delay Time during READ-MODIFY-WRITE Cycle(14) CAS to WE Delay Time(14, 20) Column-Address to WE Delay Time(14) Fast Page Mode READ or WRITE Cycle Time(24) Fast Page Mode RAS Pulse Width Access Time from CAS Precharge(15) Fast Page Mode READ-WRITE Cycle Time(24) Output Buffer Turn-Off Delay from CAS or RAS(13,15,19, 29) Last CAS going LOW to First CAS returning HIGH(23) CAS Setup Time (CBR REFRESH)(30, 20) CAS Hold Time (CBR REFRESH)(30, 21) OE Setup Time prior to RAS during HIDDEN REFRESH Cycle Refresh Period (512 Cycles) Transition Time (Rise or Fall)(2, 3) -50 Min. Max. -60 Min. Max. Units 15 — 15 — 15 — ns 8 — 10 — 15 — ns 0 6 80 45 — — — — 0 8 125 70 — — — — 0 10 140 80 — — — — ns ns ns ns 25 30 12 — — — 34 42 20 — — — 36 49 25 — — — ns ns ns 35 100K — 21 40 — 3 15 50 100K — 27 47 — 3 15 60 100K — 34 56 — 3 15 ns ns ns ns 10 — 10 — 10 — ns 8 8 0 — — — 10 10 0 — — — 10 10 0 — — — ns ns ns — 1 8 50 — 1 8 50 — 1 8 50 ms ns AC TEST CONDITIONS Output load: Two TTL Loads and 50 pF (Vcc = 5.0V ±10%) One TTL Load and 50 pF (Vcc = 3.3V ±10%) Input timing reference levels: VIH = 2.4V, VIL = 0.8V (Vcc = 5.0V ±10%); VIH = 2.0V, VIL = 0.8V (Vcc = 3.3V ±10%) Output timing reference levels: VOH = 2.0V, VOL = 0.8V (Vcc = 5V ±10%, 3.3V ±10%) Integrated Circuit Solution Inc. DR021-0A 08/11/2001 9 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S Notes: 1. An initial pause of 200 µs is required after power-up followed by eight RAS refresh cycle (RAS-Only or CBR) before proper device operation is assured. The eight RAS cycles wake-up should be repeated any time the tREF refresh requirement is exceeded. 2. VIH (MIN) and VIL (MAX) are reference levels for measuring timing of input signals. Transition times, are measured between VIH and VIL (or between VIL and VIH) and assume to be 1 ns for all inputs. 3. In addition to meeting the transition rate specification, all input signals must transit between VIH and VIL (or between VIL and VIH) in a monotonic manner. 4. If CAS and RAS = VIH, data output is High-Z. 5. If CAS = VIL, data output may contain data from the last valid READ cycle. 6. Measured with a load equivalent to one TTL gate and 50 pF. 7. Assumes that tRCD ≤ tRCD (MAX). If tRCD is greater than the maximum recommended value shown in this table, tRAC will increase by the amount that tRCD exceeds the value shown. 8. Assumes that tRCD ≥ tRCD (MAX). 9. If CAS is LOW at the falling edge of RAS, data out will be maintained from the previous cycle. To initiate a new cycle and clear the data output buffer, CAS and RAS must be pulsed for tCP. 10. Operation with the tRCD (MAX) limit ensures that tRAC (MAX) can be met. tRCD (MAX) is specified as a reference point only; if tRCD is greater than the specified tRCD (MAX) limit, access time is controlled exclusively by tCAC. 11. Operation within the tRAD (MAX) limit ensures that tRCD (MAX) can be met. tRAD (MAX) is specified as a reference point only; if tRAD is greater than the specified tRAD (MAX) limit, access time is controlled exclusively by tAA. 12. Either tRCH or tRRH must be satisfied for a READ cycle. 13. tOFF (MAX) defines the time at which the output achieves the open circuit condition; it is not a reference to VOH or VOL. 14. tWCS, tRWD, tAWD and tCWD are restrictive operating parameters in LATE WRITE and READ-MODIFY-WRITE cycle only. If tWCS ≥ tWCS (MIN), the cycle is an EARLY WRITE cycle and the data output will remain open circuit throughout the entire cycle. If tRWD ≥ tRWD (MIN), tAWD ≥ tAWD (MIN) and tCWD ≥ tCWD (MIN), the cycle is a READ-WRITE cycle and the data output will contain data read from the selected cell. If neither of the above conditions is met, the state of I/O (at access time and until CAS and RAS or OE go back to VIH) is indeterminate. OE held HIGH and WE taken LOW after CAS goes LOW result in a LATE WRITE (OE-controlled) cycle. 15. Output parameter (I/O) is referenced to corresponding CAS input, I/O0-I/O7 by LCAS and I/O8-I/O15 by UCAS. 16. During a READ cycle, if OE is LOW then taken HIGH before CAS goes HIGH, I/O goes open. If OE is tied permanently LOW, a LATE WRITE or READ-MODIFY-WRITE is not possible. 17. Write command is defined as WE going low. 18. LATE WRITE and READ-MODIFY-WRITE cycles must have both tOD and tOEH met (OE HIGH during WRITE cycle) in order to ensure that the output buffers will be open during the WRITE cycle. The I/Os will provide the previously written data if CAS remains LOW and OE is taken back to LOW after tOEH is met. 19. The I/Os are in open during READ cycles once tOD or tOFF occur. 20. The first χCAS edge to transition LOW. 21. The last χCAS edge to transition HIGH. 22. These parameters are referenced to CAS leading edge in EARLY WRITE cycles and WE leading edge in LATE WRITE or READMODIFY-WRITE cycles. 23. Last falling χCAS edge to first rising χCAS edge. 24. Last rising χCAS edge to next cycleÕs last rising χCAS edge. 25. Last rising χCAS edge to first falling χCAS edge. 26. Each χCAS must meet minimum pulse width. 27. Last χCAS to go LOW. 28. I/Os controlled, regardless UCAS and LCAS. 29. The 3 ns minimum is a parameter guaranteed by design. 30. Enables on-chip refresh and address counters. 10 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S READ CYCLE Note: 1. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. Integrated Circuit Solution Inc. DR021-0A 08/11/2001 11 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S READ WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE Cycles) 12 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S EARLY WRITE CYCLE (OE = DON'T CARE) Integrated Circuit Solution Inc. DR021-0A 08/11/2001 13 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S FAST PAGE MODE READ CYCLE 14 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S FAST PAGE MODE READ WRITE CYCLE (LATE WRITE and READ-MODIFY-WRITE Cycles) Integrated Circuit Solution Inc. DR021-0A 08/11/2001 15 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S FAST PAGE MODE EARLY WRITE CYCLE AC WAVEFORMS RAS RAS-ONLY REFRESH CYCLE (OE, WE = DON'T CARE) 16 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S CBR REFRESH CYCLE (Addresses; WE, OE = DON'T CARE) HIDDEN REFRESH CYCLE(1) (WE = HIGH; OE = LOW) Notes: 1. A Hidden Refresh may also be performed after a Write Cycle. In this case, WE = LOW and OE = HIGH. 2. tOFF is referenced from rising edge of RAS or CAS, whichever occurs last. Integrated Circuit Solution Inc. DR021-0A 08/11/2001 17 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S SELF REFRESH CYCLE (Addresses : WE and OE = DON'T CARE) TIMING PARAMETERS Symbol Min. tCHD tCP tCSR tRASS tRP tRPS tRPC 8 5 8 100 20 64 5 18 -35 Max. — — — — — — — Min. 10 9 10 100 30 84 5 -50 Max. — — — — — — — Min. 10 9 10 100 40 104 5 -60 Max. — — — — — — — Units ns ns ns µs ns ns ns Integrated Circuit Solution Inc. DR021-0A 08/11/2001 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S ORDERING INFORMATION IC41C16257 Commercial Range: 0°°C to 70°°C Speed (ns) Order Part No. 35 50 60 IC41C16257-35K IC41C16257-35T IC41C16257-50K IC41C16257-50T IC41C16257-60K IC41C16257-60T Package 400mil 400mil 400mil 400mil 400mil 400mil SOJ TSOP-2 SOJ TSOP-2 SOJ TSOP-2 ORDERING INFORMATION IC41LV16257 Commercial Range: 0°°C to 70°°C Speed (ns) Order Part No. 35 50 60 IC41LV16257-35K IC41LV16257-35T IC41LV16257-50K IC41LV16257-50T IS41LV16257-60K IC41LV16257-60T Package 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 ORDERING INFORMATION IC41C16257S Commercial Range: 0°°C to 70°°C Speed(ns) 35 50 60 OrderPartNo. Package IC41C16257S-35K IC41C16257S-35T IC41C16257S-50K IC41C16257S-50T IC41C16257S-60K IC41C16257S-60T 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 ORDERING INFORMATION IC41LV16257S Commercial Range: 0°°C to 70°°C Speed(ns) 35 50 60 OrderPartNo. Package IC41LV16257S-35K IC41LV16257S-35T IC41LV16257S-50K IC41LV16257S-50T IS41LV16257S-60K IC41LV16257S-60T 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 Integrated Circuit Solution Inc. DR021-0A 08/11/2001 Industrial Range: -40°°C to 85°°C Speed (ns) Order Part No. 35 50 60 IC41C16257-35KI IC41C16257-35TI IC41C16257-50KI IC41C16257-50TI IC41C16257-60KI IC41C16257-60TI Package 400mil 400mil 400mil 400mil 400mil 400mil SOJ TSOP-2 SOJ TSOP-2 SOJ TSOP-2 Industrial Range: -40°°C to 85°°C Speed (ns) Order Part No. 35 50 60 IC41LV16257-35KI IC41LV16257-35TI IC41LV16257-50KI IC41LV16257-50TI IC41LV16257-60KI IC41LV16257-60TI Package 400mil 400mil 400mil 400mil 400mil 400mil SOJ TSOP-2 SOJ TSOP-2 SOJ TSOP-2 Industrial Range: -40°°C to 85°°C Speed(ns) 35 50 60 Order Part No. Package IC41C16257S-35KI IC41C16257S-35TI IC41C16257S-50KI IC41C16257S-50TI IC41C16257S-60KI IC41C16257S-60TI 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 Industrial Range: -40°°C to 85°°C Speed(ns) 35 50 60 OrderPartNo. Package IC41LV16257S-35KI IC41LV16257S-35TI IC41LV16257S-50KI IC41LV16257S-50TI IC41LV16257S-60KI IC41LV16257S-60TI 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 400mil SOJ 400mil TSOP-2 19 IC41C16257/IC41C16257S IC41LV16257/IC41LV16257S Integrated Circuit Solution Inc. HEADQUARTER: NO.2, TECHNOLOGY RD. V, SCIENCE-BASED INDUSTRIAL PARK, HSIN-CHU, TAIWAN, R.O.C. TEL: 886-3-5780333 Fax: 886-3-5783000 BRANCH OFFICE: 7F, NO. 106, SEC. 1, HSIN-TAI 5TH ROAD, HSICHIH TAIPEI COUNTY, TAIWAN, R.O.C. TEL: 886-2-26962140 FAX: 886-2-26962252 http://www.icsi.com.tw 20 Integrated Circuit Solution Inc. DR021-0A 08/11/2001