I N D U C T O R S February 2015 Inductors for High Frequency Circuits Multilayer Ceramic MLG-P Series MLG0603P Type MLG0603P 0603 [0201 inch]* * Dimensions Code JIS[EIA] (2/17) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (3/17) I N D U C T O R S Inductors for High Frequency Circuits Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Multilayer Ceramic Overview of MLG0603P Type FEATURES High Q type inductor for high-frequency circuits. Inductance range: from 0.6 to 120nH. 0.1n step inductance lineup. Compared with existing products, the size was greatly reduced, making it optimal for fine-pitch circuits. Optimal configuration that greatly improves the Q to 800MHz or higher. Advanced monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for Highfrequency. APPLICATION Smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners and other high frequency circuits for the mobile communication industry PART NUMBER CONSTRUCTION MLG Series name 0603 L×W×H Dimensions (mm) 0603 0.6×0.3×0.3 P Characteristics P 0N6 B Inductance (nH) 1N1 1.1 11N 11 Inductance tolerance B ±0.1nH C ±0.2nH S ±0.3nH H ±3% J ±5% T 000 Packaging style Internal code T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Operating Storage Type temperature temperature (pieces/reel) (°C) (°C) MLG0603P –55 to +125 –55 to +125 15000 The Storage temperature range is for after the circuit board is mounted. Individual weight (mg) 0.2 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (4/17) I N D U C T O R S MLG0603P Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 30 to 60s Peak Temp. T4 250 to 260°C Time t3 10s max. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (5/17) I N D U C T O R S MLG0603P Type 0.30±0.03 SHAPE & DIMENSIONS 0.09±0.04 0.09±0.04 0.30±0.03 0.60±0.03 0.15±0.05 0.15±0.05 Dimensions in mm 0.3 RECOMMENDED LAND PATTERN 0.25 0.3 0.25 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (6/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 0.6 0.6 0.7 0.7 0.8 0.8 0.9 0.9 1.0 1.0 1.0 1.1 1.1 1.1 1.2 1.2 1.2 1.3 1.3 1.3 1.4 1.4 1.4 1.5 1.5 1.5 1.6 1.6 1.6 1.7 1.7 1.7 1.8 1.8 1.8 1.9 1.9 1.9 2.0 2.0 2.0 2.1 2.1 2.1 Tolerance ±0.1nH ±0.2nH ±0.1nH ±0.2nH ±0.1nH ±0.2nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH Q L, Q measuring frequency Self-resonant frequency DC resistance Rated current Part No. min. — — — — — — — — 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 (MHz) 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 (GHz)min. 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 9.0 9.0 9.0 9.0 9.0 9.0 8.5 8.5 8.5 8.0 8.0 8.0 (: )max. 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.07 0.07 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.08 0.08 0.08 0.09 0.09 0.09 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 (mA)max. 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 800 800 800 800 800 800 800 800 800 800 800 800 700 700 700 700 700 700 700 700 700 600 600 600 600 600 600 600 600 600 MLG0603P0N6BT000 MLG0603P0N6CT000 MLG0603P0N7BT000 MLG0603P0N7CT000 MLG0603P0N8BT000 MLG0603P0N8CT000 MLG0603P0N9BT000 MLG0603P0N9CT000 MLG0603P1N0ST000 MLG0603P1N0BT000 MLG0603P1N0CT000 MLG0603P1N1ST000 MLG0603P1N1BT000 MLG0603P1N1CT000 MLG0603P1N2ST000 MLG0603P1N2BT000 MLG0603P1N2CT000 MLG0603P1N3ST000 MLG0603P1N3BT000 MLG0603P1N3CT000 MLG0603P1N4ST000 MLG0603P1N4BT000 MLG0603P1N4CT000 MLG0603P1N5ST000 MLG0603P1N5BT000 MLG0603P1N5CT000 MLG0603P1N6ST000 MLG0603P1N6BT000 MLG0603P1N6CT000 MLG0603P1N7ST000 MLG0603P1N7BT000 MLG0603P1N7CT000 MLG0603P1N8ST000 MLG0603P1N8BT000 MLG0603P1N8CT000 MLG0603P1N9ST000 MLG0603P1N9BT000 MLG0603P1N9CT000 MLG0603P2N0ST000 MLG0603P2N0BT000 MLG0603P2N0CT000 MLG0603P2N1ST000 MLG0603P2N1BT000 MLG0603P2N1CT000 (GHz)typ. 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 20.0 19.9 19.9 19.9 16.0 16.0 16.0 13.9 13.9 13.9 11.7 11.7 11.7 14.9 14.9 14.9 13.4 13.4 13.4 12.8 12.8 12.8 10.7 10.7 10.7 10.9 10.9 10.9 10.1 10.1 10.1 9.8 9.8 9.8 (: )typ. 0.01 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.03 0.03 0.03 0.04 0.04 0.04 0.03 0.03 0.03 0.04 0.04 0.04 0.03 0.03 0.03 0.03 0.03 0.03 0.02 0.02 0.02 0.03 0.03 0.03 0.04 0.04 0.04 0.03 0.03 0.03 0.05 0.05 0.05 Please contact us for information on inductance tolerance, G (±2%). ・Short bar residual inductance =0.43nH ○ Measurement equipment Measurement item Product No. L, Q 4291B+16197A Self-resonant frequency 8720C DC resistance Type-7561 * Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (7/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 2.2 2.2 2.2 2.3 2.3 2.3 2.4 2.4 2.4 2.5 2.5 2.5 2.6 2.6 2.6 2.7 2.7 2.7 2.8 2.8 2.8 2.9 2.9 2.9 3.0 3.0 3.0 3.1 3.1 3.1 3.2 3.2 3.2 3.3 3.3 3.3 3.4 3.4 3.4 3.5 3.5 3.5 3.6 3.6 3.6 Tolerance ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH Q L, Q measuring frequency Self-resonant frequency DC resistance Rated current Part No. min. 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 (MHz) 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 (GHz)min. 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.0 7.0 7.0 6.5 6.5 6.5 6.5 6.5 6.5 (: )max. 0.10 0.10 0.10 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 (mA)max. 600 600 600 600 600 600 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 450 450 450 450 450 450 450 450 450 450 450 450 450 450 450 450 450 450 400 400 400 MLG0603P2N2ST000 MLG0603P2N2BT000 MLG0603P2N2CT000 MLG0603P2N3ST000 MLG0603P2N3BT000 MLG0603P2N3CT000 MLG0603P2N4ST000 MLG0603P2N4BT000 MLG0603P2N4CT000 MLG0603P2N5ST000 MLG0603P2N5BT000 MLG0603P2N5CT000 MLG0603P2N6ST000 MLG0603P2N6BT000 MLG0603P2N6CT000 MLG0603P2N7ST000 MLG0603P2N7BT000 MLG0603P2N7CT000 MLG0603P2N8ST000 MLG0603P2N8BT000 MLG0603P2N8CT000 MLG0603P2N9ST000 MLG0603P2N9BT000 MLG0603P2N9CT000 MLG0603P3N0ST000 MLG0603P3N0BT000 MLG0603P3N0CT000 MLG0603P3N1ST000 MLG0603P3N1BT000 MLG0603P3N1CT000 MLG0603P3N2ST000 MLG0603P3N2BT000 MLG0603P3N2CT000 MLG0603P3N3ST000 MLG0603P3N3BT000 MLG0603P3N3CT000 MLG0603P3N4ST000 MLG0603P3N4BT000 MLG0603P3N4CT000 MLG0603P3N5ST000 MLG0603P3N5BT000 MLG0603P3N5CT000 MLG0603P3N6ST000 MLG0603P3N6BT000 MLG0603P3N6CT000 (GHz)typ. 9.0 9.0 9.0 8.4 8.4 8.4 10.9 10.9 10.9 9.9 9.9 9.9 10.1 10.1 10.1 10.0 10.0 10.0 9.9 9.9 9.9 9.2 9.2 9.2 9.1 9.1 9.1 8.8 8.8 8.8 8.4 8.4 8.4 8.4 8.4 8.4 8.1 8.1 8.1 8.0 8.0 8.0 7.7 7.7 7.7 (: )typ. 0.07 0.07 0.07 0.07 0.07 0.07 0.12 0.12 0.12 0.09 0.09 0.09 0.14 0.14 0.14 0.14 0.14 0.14 0.10 0.10 0.10 0.10 0.10 0.10 0.14 0.14 0.14 0.10 0.10 0.10 0.14 0.14 0.14 0.13 0.13 0.13 0.13 0.13 0.13 0.12 0.12 0.12 0.10 0.10 0.10 Please contact us for information on inductance tolerance, G (±2%). ・Short bar residual inductance =0.43nH ○ Measurement equipment Measurement item Product No. L, Q 4291B+16197A Self-resonant frequency 8720C DC resistance Type-7561 * Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (8/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 3.7 3.7 3.7 3.8 3.8 3.8 3.9 3.9 3.9 4.0 4.0 4.0 4.1 4.1 4.1 4.2 4.2 4.2 4.3 4.3 4.3 4.7 4.7 4.7 5.1 5.1 5.1 5.6 5.6 5.6 6.2 6.2 6.2 6.8 6.8 7.5 7.5 8.2 8.2 9.1 9.1 10.0 10.0 11.0 11.0 Tolerance ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±0.1nH ±0.2nH ±0.3nH ±3% ±5% ±0.3nH ±3% ±5% ±0.3nH ±3% ±5% ±0.3nH ±3% ±5% ±0.3nH ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% Q L, Q measuring frequency Self-resonant frequency DC resistance Rated current Part No. min. 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 (MHz) 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 (GHz)min. 6.5 6.5 6.5 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.5 5.5 5.5 5.5 5.5 5.5 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 4.0 3.5 3.5 (: )max. 0.20 0.20 0.20 0.30 0.30 0.30 0.30 0.30 0.30 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.40 0.70 0.70 0.70 0.75 0.75 0.80 0.80 0.85 0.85 0.90 0.90 0.95 0.95 1.00 1.00 (mA)max. 400 400 400 400 400 400 400 400 400 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 350 300 300 300 300 300 300 300 250 250 250 250 250 250 250 250 MLG0603P3N7ST000 MLG0603P3N7BT000 MLG0603P3N7CT000 MLG0603P3N8ST000 MLG0603P3N8BT000 MLG0603P3N8CT000 MLG0603P3N9ST000 MLG0603P3N9BT000 MLG0603P3N9CT000 MLG0603P4N0ST000 MLG0603P4N0BT000 MLG0603P4N0CT000 MLG0603P4N1ST000 MLG0603P4N1BT000 MLG0603P4N1CT000 MLG0603P4N2ST000 MLG0603P4N2BT000 MLG0603P4N2CT000 MLG0603P4N3ST000 MLG0603P4N3HT000 MLG0603P4N3JT000 MLG0603P4N7ST000 MLG0603P4N7HT000 MLG0603P4N7JT000 MLG0603P5N1ST000 MLG0603P5N1HT000 MLG0603P5N1JT000 MLG0603P5N6ST000 MLG0603P5N6HT000 MLG0603P5N6JT000 MLG0603P6N2ST000 MLG0603P6N2HT000 MLG0603P6N2JT000 MLG0603P6N8HT000 MLG0603P6N8JT000 MLG0603P7N5HT000 MLG0603P7N5JT000 MLG0603P8N2HT000 MLG0603P8N2JT000 MLG0603P9N1HT000 MLG0603P9N1JT000 MLG0603P10NHT000 MLG0603P10NJT000 MLG0603P11NHT000 MLG0603P11NJT000 (GHz)typ. 7.4 7.4 7.4 7.0 7.0 7.0 7.1 7.1 7.1 6.7 6.7 6.7 6.7 6.7 6.7 6.6 6.6 6.6 6.7 6.7 6.7 6.9 6.9 6.9 6.6 6.6 6.6 5.3 5.3 5.3 6.3 6.3 6.3 6.1 6.1 5.4 5.4 5.2 5.2 5.0 5.0 4.7 4.7 4.5 4.5 (: )typ. 0.14 0.14 0.14 0.24 0.24 0.24 0.22 0.22 0.22 0.21 0.21 0.21 0.29 0.29 0.29 0.24 0.24 0.24 0.24 0.24 0.24 0.16 0.16 0.16 0.30 0.30 0.30 0.32 0.32 0.32 0.59 0.59 0.59 0.62 0.62 0.70 0.70 0.71 0.71 0.76 0.76 0.85 0.85 0.64 0.64 Please contact us for information on inductance tolerance, G (±2%). ・Short bar residual inductance =0.43nH ○ Measurement equipment Measurement item Product No. L, Q 4291B+16197A Self-resonant frequency 8720C DC resistance Type-7561 * Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (9/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 12.0 12.0 13.0 13.0 15.0 15.0 16.0 16.0 18.0 18.0 20.0 20.0 22.0 22.0 24.0 24.0 27.0 27.0 30.0 30.0 33.0 33.0 36.0 36.0 39.0 39.0 43.0 43.0 47.0 47.0 51.0 51.0 56.0 56.0 62.0 62.0 68.0 68.0 75.0 75.0 82.0 82.0 91.0 91.0 Tolerance ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% ±3% ±5% Q L, Q measuring frequency Self-resonant frequency DC resistance Rated current Part No. min. 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 9 9 9 9 9 9 9 9 (MHz) 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 500 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 300 (GHz)min. 3.5 3.5 3.2 3.2 3.2 3.2 3.0 3.0 3.0 3.0 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.6 1.6 1.6 1.6 1.4 1.4 1.4 1.4 1.2 1.2 1.2 1.2 1.0 1.0 1.0 1.0 0.9 0.9 (: )max. 1.10 1.10 1.10 1.10 1.20 1.20 1.20 1.20 1.40 1.40 1.90 1.90 1.90 1.90 2.10 2.10 2.10 2.10 2.20 2.20 2.20 2.20 2.40 2.40 2.40 2.40 2.90 2.90 2.90 2.90 3.50 3.50 3.50 3.50 3.50 3.50 3.50 3.50 4.00 4.00 4.00 4.00 4.50 4.50 (mA)max. 250 250 250 250 250 250 200 200 200 200 150 150 150 150 140 140 140 140 130 130 130 130 120 120 120 120 110 110 110 110 100 100 100 100 100 100 100 100 80 80 80 80 80 80 MLG0603P12NHT000 MLG0603P12NJT000 MLG0603P13NHT000 MLG0603P13NJT000 MLG0603P15NHT000 MLG0603P15NJT000 MLG0603P16NHT000 MLG0603P16NJT000 MLG0603P18NHT000 MLG0603P18NJT000 MLG0603P20NHT000 MLG0603P20NJT000 MLG0603P22NHT000 MLG0603P22NJT000 MLG0603P24NHT000 MLG0603P24NJT000 MLG0603P27NHT000 MLG0603P27NJT000 MLG0603P30NHT000 MLG0603P30NJT000 MLG0603P33NHT000 MLG0603P33NJT000 MLG0603P36NHT000 MLG0603P36NJT000 MLG0603P39NHT000 MLG0603P39NJT000 MLG0603P43NHT000 MLG0603P43NJT000 MLG0603P47NHT000 MLG0603P47NJT000 MLG0603P51NHT000 MLG0603P51NJT000 MLG0603P56NHT000 MLG0603P56NJT000 MLG0603P62NHT000 MLG0603P62NJT000 MLG0603P68NHT000 MLG0603P68NJT000 MLG0603P75NHT000 MLG0603P75NJT000 MLG0603P82NHT000 MLG0603P82NJT000 MLG0603P91NHT000 MLG0603P91NJT000 (GHz)typ. 4.3 4.3 4.2 4.2 3.7 3.7 3.6 3.6 3.5 3.5 3.3 3.3 2.9 2.9 2.9 2.9 2.7 2.7 2.3 2.3 2.4 2.4 2.2 2.2 2.2 2.2 2.0 2.0 2.0 2.0 1.9 1.9 1.8 1.8 1.6 1.6 1.6 1.6 1.5 1.5 1.5 1.5 1.3 1.3 (: )typ. 0.82 0.82 0.87 0.87 0.94 0.94 1.00 1.00 1.04 1.04 1.33 1.33 1.31 1.31 1.17 1.17 1.45 1.45 1.37 1.37 1.55 1.55 1.49 1.49 1.72 1.72 1.61 1.61 2.18 2.18 1.87 1.87 2.35 2.35 2.12 2.12 2.69 2.69 2.59 2.59 2.71 2.71 2.92 2.92 Please contact us for information on inductance tolerance, G (±2%). ・Short bar residual inductance =0.43nH ○ Measurement equipment Measurement item Product No. L, Q 4291B+16197A Self-resonant frequency 8720C DC resistance Type-7561 * Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (10/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (nH) 100.0 100.0 110.0 110.0 120.0 120.0 Tolerance ±3% ±5% ±3% ±5% ±3% ±5% Q L, Q measuring frequency Self-resonant frequency DC resistance Rated current Part No. min. 9 9 9 9 9 9 (MHz) 300 300 300 300 300 300 (GHz)min. 0.9 0.9 0.8 0.8 0.8 0.8 (: )max. 4.50 4.50 5.00 5.00 5.00 5.00 (mA)max. 80 80 80 80 80 80 MLG0603PR10HT000 MLG0603PR10JT000 MLG0603PR11HT000 MLG0603PR11JT000 MLG0603PR12HT000 MLG0603PR12JT000 (GHz)typ. 1.3 1.3 1.1 1.1 1.0 1.0 (: )typ. 3.20 3.20 3.50 3.50 3.79 3.79 Please contact us for information on inductance tolerance, G (±2%). ・Short bar residual inductance =0.43nH ○ Measurement equipment Measurement item Product No. L, Q 4291B+16197A Self-resonant frequency 8720C DC resistance Type-7561 * Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (11/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 0.6 0.6 0.7 0.7 0.8 0.8 0.9 0.9 1.0 1.0 1.0 1.1 1.1 1.1 1.2 1.2 1.2 1.3 1.3 1.3 1.4 1.4 1.4 1.5 1.5 1.5 1.6 1.6 1.6 1.7 1.7 1.7 1.8 1.8 1.8 1.9 1.9 1.9 2.0 2.0 2.0 2.1 2.1 2.1 2.2 2.2 2.2 2.3 2.3 2.3 Please Q typ. 800MHz 0.6 0.6 0.7 0.7 0.8 0.8 0.9 0.9 1.0 1.0 1.0 1.1 1.1 1.1 1.2 1.2 1.2 1.3 1.3 1.3 1.4 1.4 1.4 1.5 1.5 1.5 1.6 1.6 1.6 1.7 1.7 1.7 1.8 1.8 1.8 1.9 1.9 1.9 2 2 2 2.1 2.1 2.1 2.2 2.2 2.2 2.3 2.3 2.3 1.8GHz 0.6 0.6 0.7 0.7 0.8 0.8 0.9 0.9 1.0 1.0 1.0 1.1 1.1 1.1 1.2 1.2 1.2 1.3 1.3 1.3 1.4 1.4 1.4 1.5 1.5 1.5 1.6 1.6 1.6 1.7 1.7 1.7 1.8 1.8 1.8 1.9 1.9 1.9 2.0 2.0 2.0 2.1 2.1 2.1 2.2 2.2 2.2 2.3 2.3 2.3 2.0GHz 0.6 0.6 0.7 0.7 0.8 0.8 0.9 0.9 1.0 1.0 1.0 1.1 1.1 1.1 1.2 1.2 1.2 1.3 1.3 1.3 1.4 1.4 1.4 1.5 1.5 1.5 1.6 1.6 1.6 1.7 1.7 1.7 1.8 1.8 1.8 1.9 1.9 1.9 2.0 2.0 2.0 2.1 2.1 2.1 2.2 2.2 2.2 2.4 2.4 2.4 2.4GHz 0.6 0.6 0.7 0.7 0.4 0.4 0.9 0.9 1.0 1.0 1.0 1.1 1.1 1.1 1.2 1.2 1.2 1.3 1.3 1.3 1.4 1.4 1.4 1.5 1.5 1.5 1.6 1.6 1.6 1.7 1.7 1.7 1.8 1.8 1.8 1.9 1.9 1.9 2.0 2.0 2.0 2.1 2.1 2.1 2.3 2.3 2.3 2.4 2.4 2.4 500MHz 16min. 16min. 16min. 16min. 16 16 17 17 16 16 16 17 17 17 18 18 18 17 17 17 18 18 18 17 17 17 17 17 17 17 17 17 17 17 17 18 18 18 19 19 19 18 18 18 18 18 18 18 18 18 Part No. 800MHz 22min. 22min. 22min. 22min. 22 22 22 22 21 21 21 23 23 23 24 24 24 22 22 22 23 23 23 22 22 22 22 22 22 22 22 22 22 22 22 24 24 24 23 23 23 23 23 23 23 23 23 22 22 22 1.8GHz 35min. 35min. 35min. 35min. 35 35 35 35 33 33 33 36 36 36 38 38 38 34 34 34 36 36 36 33 33 33 33 33 33 33 33 33 34 34 34 36 36 36 35 35 35 34 34 34 35 35 35 33 33 33 2.0GHz 37min. 37min. 37min. 37min. 37 37 37 37 36 36 36 38 38 38 40 40 40 36 36 36 39 39 39 35 35 35 35 35 35 35 35 35 35 35 35 38 38 38 37 37 37 36 36 36 36 36 36 35 35 35 2.4GHz 41min. 41min. 41min. 41min. 41 41 41 41 40 40 40 43 43 43 45 45 45 40 40 40 43 43 43 39 39 39 38 38 38 39 39 39 39 39 39 42 42 42 41 41 41 39 39 39 40 40 40 38 38 38 MLG0603P0N6BT000 MLG0603P0N6CT000 MLG0603P0N7BT000 MLG0603P0N7CT000 MLG0603P0N8BT000 MLG0603P0N8CT000 MLG0603P0N9BT000 MLG0603P0N9CT000 MLG0603P1N0BT000 MLG0603P1N0CT000 MLG0603P1N0ST000 MLG0603P1N1BT000 MLG0603P1N1CT000 MLG0603P1N1ST000 MLG0603P1N2BT000 MLG0603P1N2CT000 MLG0603P1N2ST000 MLG0603P1N3BT000 MLG0603P1N3CT000 MLG0603P1N3ST000 MLG0603P1N4BT000 MLG0603P1N4CT000 MLG0603P1N4ST000 MLG0603P1N5BT000 MLG0603P1N5CT000 MLG0603P1N5ST000 MLG0603P1N6BT000 MLG0603P1N6CT000 MLG0603P1N6ST000 MLG0603P1N7BT000 MLG0603P1N7CT000 MLG0603P1N7ST000 MLG0603P1N8BT000 MLG0603P1N8CT000 MLG0603P1N8ST000 MLG0603P1N9BT000 MLG0603P1N9CT000 MLG0603P1N9ST000 MLG0603P2N0BT000 MLG0603P2N0CT000 MLG0603P2N0ST000 MLG0603P2N1BT000 MLG0603P2N1CT000 MLG0603P2N1ST000 MLG0603P2N2BT000 MLG0603P2N2CT000 MLG0603P2N2ST000 MLG0603P2N3BT000 MLG0603P2N3CT000 MLG0603P2N3ST000 contact us for information on inductance tolerance, G (±2%). ○ Measurement equipment Product No. Manufacturer 4291B+16197A Agilent Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (12/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 2.4 2.4 2.5 2.5 2.5 2.6 2.6 2.6 2.7 2.7 2.7 2.8 2.8 2.8 2.9 2.9 2.9 3.0 3.0 3.0 3.1 3.1 3.1 3.2 3.2 3.2 3.3 3.3 3.3 3.4 3.4 3.4 3.5 3.5 3.5 3.6 3.6 3.6 3.7 3.7 3.7 3.8 3.8 3.8 3.9 3.9 3.9 4.0 4.0 4.0 Please Q typ. 800MHz 2.4 2.4 2.5 2.5 2.5 2.6 2.6 2.6 2.7 2.7 2.7 2.8 2.8 2.8 2.9 2.9 2.9 3 3 3 3.1 3.1 3.1 3.2 3.2 3.2 3.3 3.3 3.3 3.4 3.4 3.4 3.5 3.5 3.5 3.6 3.6 3.6 3.7 3.7 3.7 3.8 3.8 3.8 3.9 3.9 3.9 4.0 4.0 4.0 1.8GHz 2.4 2.4 2.5 2.5 2.5 2.6 2.6 2.6 2.7 2.7 2.7 2.8 2.8 2.8 2.9 2.9 2.9 3.0 3.0 3.0 3.1 3.1 3.1 3.2 3.2 3.2 3.4 3.4 3.4 3.5 3.5 3.5 3.6 3.6 3.6 3.7 3.7 3.7 3.8 3.8 3.8 3.9 3.9 3.9 4.0 4.0 4.0 4.1 4.1 4.1 2.0GHz 2.4 2.4 2.5 2.5 2.5 2.6 2.6 2.6 2.7 2.7 2.7 2.8 2.8 2.8 2.9 2.9 2.9 3.1 3.1 3.1 3.2 3.2 3.2 3.3 3.3 3.3 3.4 3.4 3.4 3.5 3.5 3.5 3.6 3.6 3.6 3.7 3.7 3.7 3.9 3.9 3.9 4.0 4.0 4.0 4.1 4.1 4.1 4.2 4.2 4.2 2.4GHz 2.4 2.4 2.5 2.5 2.5 2.6 2.6 2.6 2.7 2.7 2.7 2.9 2.9 2.9 3.0 3.0 3.0 3.1 3.1 3.1 3.2 3.2 3.2 3.3 3.3 3.3 3.4 3.4 3.4 3.6 3.6 3.6 3.7 3.7 3.7 3.8 3.8 3.8 4.0 4.0 4.0 4.1 4.1 4.1 4.2 4.2 4.2 4.4 4.4 4.4 500MHz 16 16 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 17 18 18 18 18 18 18 18 18 18 18 18 18 18 18.0 18.0 17.0 17.0 17.0 17.0 17.0 17.0 18.0 18.0 18.0 Part No. 800MHz 21 21 22 22 22 22 22 22 21 21 21 22 22 22 22 22 22 21 21 21 22 22 22 22 22 22 22 22 22 23 23 23 23 23 23 22 22 22 23 23 23 22 22 22 22 22 22 22 22 22 1.8GHz 31 31 33 33 33 33 33 33 33 33 33 34 34 34 34 34 34 32 32 32 33 33 33 34 34 34 33 33 33 34 34 34 34 34 34 33 33 33 34 34 34 32 32 32 32 32 32 32 32 32 2.0GHz 33 33 34 34 34 35 35 35 35 35 35 36 36 36 35 35 35 34 34 34 34 34 34 35 35 35 35 35 35 35 35 35 35 35 35 34 34 34 35 35 35 33 33 33 34 34 34 33 33 33 2.4GHz 36 36 38 38 38 38 38 38 38 38 38 40 40 40 39 39 39 37 37 37 37 37 37 38 38 38 38 38 38 38 38 38 38 38 38 37 37 37 37 37 37 36 36 36 36 36 36 36 36 36 MLG0603P2N4BT000 MLG0603P2N4ST000 MLG0603P2N5BT000 MLG0603P2N5CT000 MLG0603P2N5ST000 MLG0603P2N6BT000 MLG0603P2N6CT000 MLG0603P2N6ST000 MLG0603P2N7BT000 MLG0603P2N7CT000 MLG0603P2N7ST000 MLG0603P2N8BT000 MLG0603P2N8CT000 MLG0603P2N8ST000 MLG0603P2N9BT000 MLG0603P2N9CT000 MLG0603P2N9ST000 MLG0603P3N0BT000 MLG0603P3N0CT000 MLG0603P3N0ST000 MLG0603P3N1BT000 MLG0603P3N1CT000 MLG0603P3N1ST000 MLG0603P3N2BT000 MLG0603P3N2CT000 MLG0603P3N2ST000 MLG0603P3N3BT000 MLG0603P3N3CT000 MLG0603P3N3ST000 MLG0603P3N4BT000 MLG0603P3N4CT000 MLG0603P3N4ST000 MLG0603P3N5BT000 MLG0603P3N5CT000 MLG0603P3N5ST000 MLG0603P3N6BT000 MLG0603P3N6CT000 MLG0603P3N6ST000 MLG0603P3N7BT000 MLG0603P3N7CT000 MLG0603P3N7ST000 MLG0603P3N8BT000 MLG0603P3N8CT000 MLG0603P3N8ST000 MLG0603P3N9BT000 MLG0603P3N9CT000 MLG0603P3N9ST000 MLG0603P4N0BT000 MLG0603P4N0CT000 MLG0603P4N0ST000 contact us for information on inductance tolerance, G (±2%). ○ Measurement equipment Product No. Manufacturer 4291B+16197A Agilent Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (13/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 4.1 4.1 4.1 4.2 4.2 4.2 4.3 4.3 4.3 4.7 4.7 4.7 5.1 5.1 5.1 5.6 5.6 5.6 6.2 6.2 6.2 6.8 6.8 7.5 7.5 8.2 8.2 9.1 9.1 10 10 11 11 12 12 13 13 15 15 16 16 18 18 20 20 22 22 24 24 27 27 Please Q typ. 800MHz 4.1 4.1 4.1 4.2 4.2 4.2 4.3 4.3 4.3 4.7 4.7 4.7 5.1 5.1 5.1 5.6 5.6 5.6 6.2 6.2 6.2 6.8 6.8 7.5 7.5 8.2 8.2 9.1 9.1 10 10 11 11 12 12 13 13 15 15 16 16 18 18 21 21 23 23 25 25 28 28 1.8GHz 4.3 4.3 4.3 4.4 4.4 4.4 4.5 4.5 4.5 4.9 4.9 4.9 5.3 5.3 5.3 6.1 6.1 6.1 6.5 6.5 6.5 7.3 7.3 8.1 8.1 9.0 9.0 10.0 10.0 11 11 13 13 14 14 15 15 18 18 20 20 23 23 27 27 34 34 36 36 45 45 2.0GHz 4.3 4.3 4.3 4.5 4.5 4.5 4.5 4.5 4.5 5.0 5.0 5.0 5.4 5.4 5.4 6.2 6.2 6.2 6.7 6.7 6.7 7.5 7.5 8.3 8.3 9.3 9.3 10.3 10.3 12 12 13 13 15 15 16 16 20 20 22 22 26 26 31 31 40 40 43 43 57 57 2.4GHz 4.5 4.5 4.5 4.6 4.6 4.6 4.7 4.7 4.7 5.1 5.1 5.1 5.7 5.7 5.7 6.6 6.6 6.6 7.0 7.0 7.0 8.0 8.0 8.8 8.8 10.0 10.0 11.1 11.1 13 13 15 15 17 17 19 19 24 24 27 27 33 33 42 42 68 68 72 72 500MHz 18.0 18.0 18.0 18.0 18.0 18 17 17 17 16 16 16 16 16 16 18 18 18 16 16 16 16 16 16 16 17 17 17 17 16 16 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 18 19 19 18 18 Part No. 800MHz 22 22 22 22 22 22 21 21 21 21 21 21 21 21 21 22 22 22 21 21 21 21 21 21 21 21 21 21 21 21 21 23 23 22 22 22 22 22 22 22 22 22 22 22 22 21 21 22 22 21 21 1.8GHz 33 33 33 32 32 32 32 32 32 31 31 31 31 31 31 31 31 31 30 30 30 29 29 30 30 30 30 30 30 28 28 30 30 28 28 28 28 27 27 26 26 25 25 23 23 21 21 21 21 18 18 2.0GHz 34 34 34 33 33 33 33 33 33 32 32 32 32 32 32 32 32 32 31 31 31 30 30 30 30 30 30 31 31 28 28 30 30 28 28 28 28 26 26 25 25 24 24 22 22 18 18 18 18 15 15 2.4GHz 36 36 36 35 35 35 35 35 35 34 34 34 34 34 34 32 32 32 33 33 33 31 31 32 32 31 31 32 32 28 28 30 30 27 27 26 26 24 24 22 22 20 20 17 17 11 11 11 11 MLG0603P4N1BT000 MLG0603P4N1CT000 MLG0603P4N1ST000 MLG0603P4N2BT000 MLG0603P4N2CT000 MLG0603P4N2ST000 MLG0603P4N3ST000 MLG0603P4N3HT000 MLG0603P4N3JT000 MLG0603P4N7ST000 MLG0603P4N7HT000 MLG0603P4N7JT000 MLG0603P5N1ST000 MLG0603P5N1HT000 MLG0603P5N1JT000 MLG0603P5N6ST000 MLG0603P5N6HT000 MLG0603P5N6JT000 MLG0603P6N2ST000 MLG0603P6N2HT000 MLG0603P6N2JT000 MLG0603P6N8HT000 MLG0603P6N8JT000 MLG0603P7N5HT000 MLG0603P7N5JT000 MLG0603P8N2HT000 MLG0603P8N2JT000 MLG0603P9N1HT000 MLG0603P9N1JT000 MLG0603P10NHT000 MLG0603P10NJT000 MLG0603P11NHT000 MLG0603P11NJT000 MLG0603P12NHT000 MLG0603P12NJT000 MLG0603P13NHT000 MLG0603P13NJT000 MLG0603P15NHT000 MLG0603P15NJT000 MLG0603P16NHT000 MLG0603P16NJT000 MLG0603P18NHT000 MLG0603P18NJT000 MLG0603P20NHT000 MLG0603P20NJT000 MLG0603P22NHT000 MLG0603P22NJT000 MLG0603P24NHT000 MLG0603P24NJT000 MLG0603P27NHT000 MLG0603P27NJT000 contact us for information on inductance tolerance, G (±2%). ○ Measurement equipment Product No. Manufacturer 4291B+16197A Agilent Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (14/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS L, Q FREQUENCY CHARACTERISTICS TABLE L(nH)typ. 500MHz 30 30 33 33 37 37 40 40 44 44 48 48 53 53 58 58 65 65 71 71 79 79 87 87 99 99 110 110 126 126 151 151 Please Q typ. 800MHz 32 32 36 36 39 39 43 43 48 48 53 53 59 59 66 66 76 76 82 82 97 97 109 109 132 132 152 152 211 211 1.8GHz 59 59 68 68 2.0GHz 2.4GHz 500MHz 18 18 15 15 16 16 15 15 15 15 15 15 15 15 15 15 15 15 15 15 14 14 14 14 13 13 14 14 13 13 12 12 Part No. 800MHz 21 21 17 17 17 17 17 17 16 16 16 16 16 16 15 15 15 15 15 15 13 13 13 13 12 12 12 12 9 9 1.8GHz 15 15 11 11 2.0GHz 2.4GHz MLG0603P30NHT000 MLG0603P30NJT000 MLG0603P33NHT000 MLG0603P33NJT000 MLG0603P36NHT000 MLG0603P36NJT000 MLG0603P39NHT000 MLG0603P39NJT000 MLG0603P43NHT000 MLG0603P43NJT000 MLG0603P47NHT000 MLG0603P47NJT000 MLG0603P51NHT000 MLG0603P51NJT000 MLG0603P56NHT000 MLG0603P56NJT000 MLG0603P62NHT000 MLG0603P62NJT000 MLG0603P68NHT000 MLG0603P68NJT000 MLG0603P75NHT000 MLG0603P75NJT000 MLG0603P82NHT000 MLG0603P82NJT000 MLG0603P91NHT000 MLG0603P91NJT000 MLG0603PR10HT000 MLG0603PR10JT000 MLG0603PR11HT000 MLG0603PR11JT000 MLG0603PR12HT000 MLG0603PR12JT000 contact us for information on inductance tolerance, G (±2%). ○ Measurement equipment Product No. Manufacturer 4291B+16197A Agilent Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (15/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 1000 R10 R12 82N 68N 56N 47N39N 33N 27N 22N 100 18N 15N Inductance(nH) 12N 10N 8N2 10 6N8 5N6 4N7 3N9 3N3 2N7 2N2 1N8 1N5 1N2 1 1N0 0 10 100 1000 10000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16197A Agilent Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (16/17) I N D U C T O R S MLG0603P Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE) 50 1N2 1N0 1N5 1N8 2N7 3N3 40 2N2 3N9 4N7 5N6 30 6N8 Q 8N2 10N 12N 20 15N 18N 10 56N 82N 47N 39N 68N 33N 22N R12 0 10 R10 27N 100 1000 10000 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer E4991A+16197A Agilent Technologies * Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm (17/17) I N D U C T O R S MLG0603P Type PACKAGING STYLE REEL DIMENSIONS ø60min. 1.0 2.0±0.5 8.4 +2.0 –0.0 ø13±0.2 14.4max. ø21±0.8 ø180±2.0 Dimensions in mm Cavity 3.5±0.05 1.5 +0.1 –0.0 Type MLG0603P A 0.68±0.05 B 0.38±0.05 K 0.5 max. A 8.0±0.3 Sprocket hole 1.75±0.1 TAPE DIMENSIONS K B 4.0±0.1 2.0±0.05 160min. Drawing direction Taping 2.0±0.05 200min. 300min. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20150216 / inductor_commercial_high-frequency_mlg0603p_en.fm