Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch PART NUMBER DESCRIPTION CCP-38S Commercial Normally Open Multi-throw, DC-3GHz, Low PIM These switches have extremely low passive intermodulation for use in narrow bandwidth communications applications. The CCP38S is a broadband, multi-throw, electromechanical coaxial switch designed to switch a microwave signal from a common input to any of 3, 4, 5, or 6 outputs. The characteristic impedance is 50 Ohms. The switches are small using the popular connector spacing on a 1.062” dia. circle. Each position has an individual actuator mechanism allowing random position selection. This also gives the minimum switching time. With the normally open actuator, all paths are open when the switch is de-energized. ENVIRONMENTAL AND PHYSICAL CHARACTERISTICS ELECTRICAL CHARACTERISTICS Operating Temperature –40°C to 65°C Form Factor Vibration (MIL-STD-202 Method 214, Condition D, non-operating) 10 g’s RMS Shock (MIL-STD-202 Method 213, Condition D, non-operating) 500 g’s Standard Actuator Life 1,000,000 cycles Connector Type SMA Humidity (Moisture Seal) Available Weight 9 oz. (255.2g) (max.) Multi-Throw, break before make Frequency Range DC–3 GHz Characteristic Impedance 50 Ohms Switching Time 15 ms (max.) Actuation Voltage Available 12 15 24 28 V Actuation Current, max. @ ambient 400 205 170 140 mA PERFORMANCE CHARACTERISTICS PASSIVE INTERMODULATION CHARACTERISTICS Frequency Tone 1 Frequency (MHz) Tone 2 Frequency (MHz) IM3 Frequency (MHz) PIM Threshold (dBc) 1945 1990 1900 -140.0 P1 P2 (dBm) PIM (dBc) PEAK PIM (dBc) 43 -153.9 -144.1 DC–3 GHz Insertion Loss, dB, max. 0.2 Isolation, dB, min. 70 VSWR , max. 1.25:1 RF Power (cw), W, max. 100 PART NUMBERING SYSTEM CCP-38 S 1 6 C - T ** Series Options Connectors Actuator Type Actuator Voltage Number of Positions CONNECTOR ACTUATOR VOLTAGE NUMBER OF POSITIONS ACTUATOR TYPE OPTIONS S: SMA FEMALE 1: 28 VDC NORMALLY OPEN 3: SP3T 0: NO INDICATOR CONTACTS T: TTL DRIVERS WITH DIODES 2: 15 VDC NORMALLY OPEN 4: SP4T C: INDICATOR CONTACTS D: COIL TRANSIENT SUPPRESSION DIODES 3: 12 VDC NORMALLY OPEN 5: SP5T S: D-SUB CONNECTOR* 4: 24 VDC NORMALLY OPEN 6: SP6T TD: DECODERS AND TTL DRIVERS WITH DIODES **SEE PARTS LIST ON PAGE 10 For additional options, please contact factory. © 2013 TELEDYNE RELAYS (800) 284-7007 • www.teledynecoax.com M: MOISTURE SEAL * D-Sub Connector may be 9 or 15 pin depending on number of throws. (See Connector Pinout page) CCP-38S Page 1 CCP-38S\072013\Q3 Series CCP-38S Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch COAX SWITCHES SCHEMATICS AND MECHANICAL OUTLINE TELEDYNE COAX SWITCHES P/N: VOLTAGE: VDC D/C: M/O: RoHS MADE IN SCHEMATIC SHOWN IN NORMALLY OPEN POSITION CCP-38S Page 2 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2013 TELEDYNE COAX SWITCHES CCP-38S\072013\Q3 Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch CONNECTOR PINOUT FOR NORMALLY OPEN SP3T MULTI-THROW SWITCHES EXAMPLE CCP-38S130-S CCP-38S13C-S INDICATOR CCP-38S130-TS YES CCP-38S13C-TS CCP-38S130-TDS YES TTL YES YES CCP-38S13C-TDS YES DECODERS & TTL YES YES 9-PIN 9-PIN 9-PIN 9-PIN 9-PIN 9-PIN 1 PORT 1 PORT 1 PORT 1 PORT 1 LOGIC 1 LOGIC 1 2 PORT 2 PORT 2 PORT 2 PORT 2 LOGIC 2 LOGIC 2 3 PORT 3 PORT 3 PORT 3 PORT 3 PIN NO. 4 E INDICATOR E INDICATOR 5 F INDICATOR F INDICATOR F INDICATOR 6 G INDICATOR G INDICATOR G INDICATOR 7 COMMON COMMON COMMON 8 VSW 9 D INDICATOR (COM) E INDICATOR COMMON COMMON VSW VSW D INDICATOR (COM) COMMON VSW D INDICATOR (COM) CONNECTOR PINOUT FOR NORMALLY OPEN SP4T MULTI-THROW SWITCHES EXAMPLE CCP-38S140-S CCP-38S14C-S CCP-38S140-TS YES INDICATOR TTL CCP-38S14C-TS CCP-38S140-TDS YES YES YES CCP-38S14C-TDS YES DECODERS & TTL YES YES 9-PIN 15-PIN 9-PIN 15-PIN 9-PIN 15-PIN 1 PORT 1 PORT 1 TTL 1 TTL 1 LOGIC 1 LOGIC 1 2 PORT 2 PORT 2 TTL 2 TTL 2 LOGIC 2 LOGIC 2 3 PORT 3 PORT 3 TTL 3 TTL 3 LOGIC 3 LOGIC 3 4 PORT 4 PORT 4 TTL 4 TTL 4 COMMON COMMON COMMON COMMON COMMON COMMON VSW VSW VSW PIN NO. 5 6 7 8 VSW 9 D INDICATOR (COM) D INDICATOR (COM) D INDICATOR (COM) 10 E INDICATOR E INDICATOR E INDICATOR 11 F INDICATOR F INDICATOR F INDICATOR 12 G INDICATOR G INDICATOR G INDICATOR N/A N/A 13 H INDICATOR N/A H INDICATOR H INDICATOR 14 15 1 6 9-PIN D-SUB CONNECTOR © 2013 TELEDYNE RELAYS 15-PIN D-MICRO CONNECTOR (800) 284-7007 • www.teledynecoax.com CCP-38S Page 3 CCP-38S\072013\Q3 Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch CONNECTOR PINOUT FOR NORMALLY OPEN SP5T MULTI-THROW SWITCHES EXAMPLE CCP-38S150-S CCP-38S15C-S CCP-38S150-TS YES INDICATOR TTL CCP-38S15C-TS CCP-38S150-TDS YES YES YES CCP-38S15C-TDS YES DECODERS & TTL YES YES 9-PIN 15-PIN 9-PIN 15-PIN 9-PIN 15-PIN 1 PORT 1 PORT 1 TTL 1 TTL 1 LOGIC 1 LOGIC 1 2 PORT 2 PORT 2 TTL 2 TTL 2 LOGIC 2 LOGIC 2 3 PORT 3 PORT 3 TTL 3 TTL 3 LOGIC 3 LOGIC 3 4 PORT 4 PORT 4 TTL 4 TTL 4 5 PORT 5 PORT 5 TTL 5 TTL 5 COMMON COMMON COMMON COMMON COMMON COMMON VSW VSW VSW PIN NO. 6 7 8 VSW 9 D INDICATOR (COM) D INDICATOR (COM) D INDICATOR (COM) 10 E INDICATOR E INDICATOR E INDICATOR 11 F INDICATOR F INDICATOR F INDICATOR 12 G INDICATOR G INDICATOR G INDICATOR N/A N/A N/A 13 H INDICATOR H INDICATOR H INDICATOR 14 K INDICATOR K INDICATOR K INDICATOR 15 CONNECTOR PINOUT FOR NORMALLY OPEN SP6T MULTI-THROW SWITCHES EXAMPLE CCP-38S160-S CCP-38S16C-S CCP-38S160-TS YES INDICATOR TTL CCP-38S16C-TS CCP-38S160-TDS YES YES YES DECODERS & TTL CCP-38S16C-TDS YES YES YES 9-PIN 15-PIN 9-PIN 15-PIN 9-PIN 15-PIN 1 PORT 1 PORT 1 TTL 1 TTL 1 LOGIC 1 LOGIC 1 2 PORT 2 PORT 2 TTL 2 TTL 2 LOGIC 2 LOGIC 2 3 PORT 3 PORT 3 TTL 3 TTL 3 LOGIC 3 LOGIC 3 4 PORT 4 PORT 4 TTL 4 TTL 4 5 PORT 5 PORT 5 TTL 5 TTL 5 6 PORT 6 PORT 6 TTL 6 TTL 6 7 COMMON COMMON COMMON COMMON COMMON COMMON VSW VSW VSW PIN NO. 8 VSW 9 D INDICATOR (COM) D INDICATOR (COM) D INDICATOR (COM) 10 E INDICATOR E INDICATOR E INDICATOR 11 F INDICATOR F INDICATOR F INDICATOR 12 G INDICATOR G INDICATOR G INDICATOR N/A N/A N/A 13 H INDICATOR H INDICATOR H INDICATOR 14 K INDICATOR K INDICATOR K INDICATOR 15 L INDICATOR L INDICATOR L INDICATOR CCP-38S Page 4 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2013 TELEDYNE COAX SWITCHES CCP-38S\072013\Q3 Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch TRUTH TABLE Normally Open CCP-38SX3C-T Logic Input 1 2 RF Path 3 J1 J2 Indicator Switches J3 E F G 1 0 0 On Off Off C 0 0 0 1 0 Off On Off 0 C 0 0 0 1 Off Off On 0 0 C TRUTH TABLE Normally Open CCP-38SX3C-TD Logic Input 1 RF Path 2 J1 J2 Indicator Switches J3 E F G 0 0 On Off Off C 0 0 1 0 Off On Off 0 C 0 0 1 Off Off On 0 0 C 1 1 Off Off Off 0 0 0 TRUTH TABLE Normally Open CCP-38SX4C-T Logic Input RF Path Indicator Switches 1 2 3 4 J1 J2 J3 J4 E F G H 1 0 0 0 On Off Off Off C 0 0 0 0 1 0 0 Off On Off Off 0 C 0 0 0 0 1 0 Off Off On Off 0 0 C 0 0 0 0 1 Off Off Off On 0 0 0 C TRUTH TABLE Normally Open CCP-38SX4C-TD Logic Input RF Path Indicator Switches 1 2 3 J1 J2 J3 J4 E F G H 0 0 0 On Off Off Off C 0 0 0 1 0 0 Off On Off Off 0 C 0 0 0 1 0 Off Off On Off 0 0 C 0 1 1 0 Off Off Off On 0 0 0 C 1 1 1 Off Off Off Off 0 0 0 0 © 2013 TELEDYNE RELAYS (800) 284-7007 • www.teledynecoax.com CCP-38S Page 5 CCP-38S\072013\Q3 Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch TRUTH TABLE Normally Open CCP-38SX5C-T Logic Input RF Path Indicator Switches 1 2 3 4 5 J1 J2 J3 J4 J5 E F G H K 1 0 0 0 0 On Off Off Off Off C 0 0 0 0 0 1 0 0 0 Off On Off Off Off 0 C 0 0 0 0 0 1 0 0 Off Off On Off Off 0 0 C 0 0 0 0 0 1 0 Off Off Off On Off 0 0 0 C 0 0 0 0 0 1 Off Off Off Off On 0 0 0 0 C TRUTH TABLE Normally Open CCP-38SX5C-TD Logic Input RF Path Indicator Switches 1 2 3 J1 J2 J3 J4 J5 E F G H K 0 0 0 On Off Off Off Off C 0 0 0 0 1 0 0 Off On Off Off Off 0 C 0 0 0 0 1 0 Off Off On Off Off 0 0 C 0 0 1 1 0 Off Off Off On Off 0 0 0 C 0 0 0 1 Off Off Off Off On 0 0 0 0 C 1 1 1 Off Off Off Off Off 0 0 0 0 0 TRUTH TABLE Normally Open CCP-38SX6C-T Logic Input RF Path 1 2 3 4 5 6 1 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 Off 0 0 0 1 0 0 Off 0 0 0 0 1 0 Off 0 0 0 0 0 1 Off J3 J4 Indicator Switches J1 J2 J5 J6 E F G H K L 0 On Off Off Off 0 Off On Off Off Off Off Off Off C 0 0 0 0 0 0 C 0 0 0 0 Off On Off Off Off Off Off On Off Off 0 0 C 0 0 0 0 0 0 C 0 0 Off Off Off On Off 0 0 Off Off Off Off On 0 0 0 0 C 0 0 0 0 C TRUTH TABLE Normally Open CCP-38SX6C-TD Logic Input RF Path Indicator Switches 1 2 3 J1 J2 J3 J4 J5 J6 E F G H K L 0 0 0 On Off Off Off Off Off C 0 0 0 0 0 1 0 0 Off On Off Off Off Off 0 C 0 0 0 0 0 1 0 Off Off On Off Off Off 0 0 C 0 0 0 1 1 0 Off Off Off On Off Off 0 0 0 C 0 0 0 0 1 Off Off Off Off On Off 0 0 0 0 C 0 1 0 1 Off Off Off Off Off On 0 0 0 0 0 C 1 1 1 Off Off Off Off Off Off 0 0 0 0 0 0 CCP-38S Page 6 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2013 TELEDYNE COAX SWITCHES CCP-38S\072013\Q3 Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch TYPICAL BROADBAND RF PERFORMANCE CURVES Insertion Loss (DC-3 GHz) 0.0 -0.1 Insertion Loss (dB) -0.2 -0.3 -0.4 -0.5 -0.6 -0.7 -0.8 -0.9 -1.0 0 0.5 1 1.5 2 2.5 3 Frequency (GHz) Isolation (DC-3 GHz) 0 -20 Isolation (dB) -40 -60 -80 -100 -120 0 0.5 1 1.5 2 2.5 3 Frequency (GHz) VSWR (DC-3 GHz) 1.25 VSWR (dB) 1.20 1.15 1.10 1.05 1.00 0 0.5 1 1.5 2 2.5 3 Frequency (GHz) RF NOTES © 2013 TELEDYNE RELAYS (800) 284-7007 • www.teledynecoax.com CCP-38S Page 7 CCP-38S\072013\Q3 Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch TYPICAL POWER PERFORMANCE CURVE Power Handling vs. Frequency 3000 2000 1000 800 600 STA Power (W) 400 ND 300 ARD 200 SM AS WIT CH ES 100 80 60 40 30 20 10 .1 .2 .3 .4 .6 .8 1 2 3 Frequency GHz Estimates based on the following reference conditions: • Ambient temperature of 40°C or less • Sea level operation • Load VSWR of 1.20:1 maximum • No high-power (hot) switching Please contact Teledyne Coax Switches for derating factors when applications do not meet the foregoing reference conditions. CCP-38S Page 8 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2013 TELEDYNE COAX SWITCHES CCP-38S\072013\Q3 Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch GLOSSARY Actuator An actuator is the electromechanical mechanism that transfers the RF contacts from one position to another upon DC command. Arc Suppression Diode A diode is connected in parallel with the coil. This diode limits the “reverse EMF spike” generated when the coil deenergizes to 0.7 volts. The diode cathode is connected to the positive side of the coil and the anode is connected to the negative side. Date Code All switches are marked with either a unique serial number or a date code. Date codes are in accordance with MILSTD-1285 Paragraph 5.2.5 and consist of four digits. The first two digits define the year and the last two digits define the week of the year (YYWW). Thus, 1032 identifies switches that passed through final inspection during the 32nd week of 2010. Indicator Indicators tell the system which position the switch is in. Other names for indicators are telemetry contacts or tellback circuit. Indicators are usually a set of internally mounted DC contacts linked to the actuator. They can be wired to digital input lines, status lights, or interlocks. Unless otherwise specified, the maximum indicator contact rating is 30 Vdc, 50 mA, or 1.5 Watts into a resistive load. Isolation Isolation is the measure of the power level at the output connector of an unconnected RF channel as referenced to the power at the input connector. It is specified in dB below the input power level. Multi-Throw Switch A multi-throw switch is a switch with one input and three or more output ports. The CCR-38 can switch a microwave signal to any of 2,3,4,5 or 6 output from a single common input. TD-Option This option includes a decoder. The 3-bit parallel command is decoded to internally select the appropriate position. See the logic tables. The TD-Option increases the Vsw supply current demand by 50mA max at 28Vdc and +20°C. Performance Parameters vs Frequency Generally speaking, the RF performance of coaxial switches is frequency dependent. With increasing frequency, VSWR and insertion loss increase while isolation decreases. All data sheets specify these three parameters as “worst case” at the highest operating frequency. If the switch is to be used over a narrow frequency band, better performance can be achieved. Actuator Current vs Temperature The resistance of the actuator coil varies as a function of temperature. There is an inverse relationship between the operating temperature of the switch and the actuator drive current. For switches operating at 28 VDC, the approximate actuator drive current at temperature, T, can be calculated using the equation: IT = IA [1 + .00385 (T-20)] Where: IT = Actuator current at temperature, T IA = Room temperature actuator current – see data sheet T = Temperature of interest in °C Magnetic Sensitivity An electro-mechanical switch can be sensitive to ferrous materials and external magnetic fields. Neighboring ferrous materials should be permitted no closer than 0.5 inches and adjacent external magnetic fields should be limited to a flux density of less than 5 Gauss. Switching Time Switching time is the total interval beginning with the arrival of the leading edge of the command pulse at the switch DC input and ending with the completion of the switch transfer, including contact bounce. It consists of three parts: (1) inductive delay in the coil, (2) transfer time of the physical movement of the contacts, and (3) the bounce time of the RF contacts. TTL Switch Driver Option As a special option, switch drivers can be provided for both failsafe and latching switches, which are compatible with industry-standard low-power Schottky TTL circuits. © 2013 TELEDYNE RELAYS (800) 284-7007 • www.teledynecoax.com CCP-38S Page 9 CCP-38S\072013\Q3 Series CCP-38S COAX SWITCHES Low PIM Multi-Throw DC–3 GHz Normally Open Coaxial Switch NORMALLY OPEN CCP-38S PART NUMBER LIST PART NO. 1 * CCP-38SX3C PART NO. 43 CCP-38SX40 PART NO. 85 CCP-38SX6C 2 CCP-38SX3C-D 44 CCP-38SX40-D 86 CCP-38SX6C-D 3 CCP-38SX3C-DM 45 CCP-38SX40-DM 87 CCP-38SX6C-DM 4 CCP-38SX3C-M 46 CCP-38SX40-M 88 CCP-38SX6C-M 5 CCP-38SX3C-MS 47 CCP-38SX40-MS 89 CCP-38SX6C-MS 6 CCP-38SX3C-S 48 CCP-38SX40-S 90 CCP-38SX6C-S 7 CCP-38SX3C-T 49 CCP-38SX40-T 91 CCP-38SX6C-T 8 CCP-38SX3C-TD 50 CCP-38SX40-TD 92 CCP-38SX6C-TD 9 CCP-38SX3C-TDM 51 CCP-38SX40-TDM 93 CCP-38SX6C-TDM 10 CCP-38SX3C-TDMS 52 CCP-38SX40-TDMS 94 CCP-38SX6C-TDMS 11 CCP-38SX3C-TDS 53 CCP-38SX40-TDS 95 CCP-38SX6C-TDS 12 CCP-38SX3C-TM 54 CCP-38SX40-TM 96 CCP-38SX6C-TM 13 CCP-38SX3C-TMS 55 CCP-38SX40-TMS 97 CCP-38SX6C-TMS 14 CCP-38SX3C-TS 56 CCP-38SX40-TS 98 CCP-38SX6C-TS 15 CCP-38SX30 57 CCP-38SX5C 99 CCP-38SX60 16 CCP-38SX30-D 58 CCP-38SX5C-D 100 CCP-38SX60-D 17 CCP-38SX30-DM 59 CCP-38SX5C-DM 101 CCP-38SX60-DM 18 CCP-38SX30-M 60 CCP-38SX5C-M 102 CCP-38SX60-M 19 CCP-38SX30-MS 61 CCP-38SX5C-MS 103 CCP-38SX60-MS 20 CCP-38SX30-S 62 CCP-38SX5C-S 104 CCP-38SX60-S 21 CCP-38SX30-T 63 CCP-38SX5C-T 105 CCP-38SX60-T 22 CCP-38SX30-TD 64 CCP-38SX5C-TD 106 CCP-38SX60-TD 23 CCP-38SX30-TDM 65 CCP-38SX5C-TDM 107 CCP-38SX60-TDM 24 CCP-38SX30-TDMS 66 CCP-38SX5C-TDMS 108 CCP-38SX60-TDMS 25 CCP-38SX30-TDS 67 CCP-38SX5C-TDS 109 CCP-38SX60-TDS 26 CCP-38SX30-TM 68 CCP-38SX5C-TM 110 CCP-38SX60-TM 27 CCP-38SX30-TMS 69 CCP-38SX5C-TMS 111 CCP-38SX60-TMS 28 CCP-38SX30-TS 70 CCP-38SX5C-TS 112 CCP-38SX60-TS 29 CCP-38SX4C 71 CCP-38SX50 30 CCP-38SX4C-D 72 CCP-38SX50-D 31 CCP-38SX4C-DM 73 CCP-38SX50-DM 32 CCP-38SX4C-M 74 CCP-38SX50-M 33 CCP-38SX4C-MS 75 CCP-38SX50-MS 34 CCP-38SX4C-S 76 CCP-38SX50-S 35 CCP-38SX4C-T 77 CCP-38SX50-T 36 CCP-38SX4C-TD 78 CCP-38SX50-TD 37 CCP-38SX4C-TDM 79 CCP-38SX50-TDM 38 CCP-38SX4C-TDMS 80 CCP-38SX50-TDMS 39 CCP-38SX4C-TDS 81 CCP-38SX50-TDS 40 CCP-38SX4C-TM 82 CCP-38SX50-TM 41 CCP-38SX4C-TMS 83 CCP-38SX50-TMS 42 CCP-38SX4C-TS 84 CCP-38SX50-TS X = 1 (28Vdc), 2 (15Vdc), 3 (12Vdc) and 4 (24Vdc) CCP-38S Page 10 SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE © 2013 TELEDYNE COAX SWITCHES CCP-38S\072013\Q3