GMT G1224P1U Dual rail-to-rail i/o, high-slew-rate op amp Datasheet

G1224
Global Mixed-mode Technology Inc.
Dual Rail-to-Rail I/O, High-Slew-Rate OP Amp
Features
General Description
„
G1224 is a input/output rail-to-rail Operational Amplifier. It can be operated from +3V to +5.5V single supply or from ±1.5V to ±2.75 dual supply. G1224 can
drive 66mA into resistor loads to within 10% power rail
each amplifier. AC performance is very excellent with
2.5MHz bandwidth, 6V/µs Slew Rate, 95dB open loop
gain, 60 degree phase margin and low distortion.
„
„
„
„
„
„
„
„
+3V to +5.5V Single-Supply Operation
Input / Output Rail-to-Rail
Low Input Current
High Output Driving Capacity
Low Quiescent Current: 1mA @ 5V
High Slew Rate 6V/µs
High Gain-Bandwidth Product 2.5MHz
High Open Loop Gain 95dB
High PSRR 70dB
Supply current of G1224 is only 500µA per Amplifier. It
is very suitable for low current consumption applications to control high current loads. Applications include
audio amplification for computers, sound ports, sound
cards and set-top boxes.
Applications
„
„
„
„
„
„
„
Headphone Driver
Portable Equipment
Battery-Powered Equipment
Multimedia Audio
ASIC Input or Output Amplifier
Sensor Amplifier
Low Power/Low Voltage Applications
G1224 is available in 8pins SOP-8, MSOP-8, TSSOP-8
and SOT-23-8 package.
Ordering Information
ORDER
NUMBER
MARKING
TEMP.
RANGE
PACKAGE
(Pb free)
G1224P1U
G1224P8U
G1224D1U
G1224
G1224
G1224
0°C to 85°C
0°C to 85°C
0°C to 85°C
SOP-8
MSOP-8
TSSOP-8
G1224TMU
1224x
0°C to 85°C
SOT-23-8
Note: P1:SOP-8
P8: MSOP-8
D1:TSSOP-8 TM: SOT-23-8
U: Tape & Reel
Pin Configuration
Typical Application Circuit
VDD
G1224
OUTA
1
8
VDD
INA+
2
INA+
3
VSS
4
+
7
OUTB
8
+
G1224
1
OUTA
2 +
-
INA-
3
6
INB-
5
INB+
4
RL
2K
SOP-8/MSOP-8/
TSSOP-8/SOT-23-8
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.5
Mar 02, 2007
1
G1224
Global Mixed-mode Technology Inc.
Absolute Maximum Ratings
θJA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .240°C/Watt
Junction Temperature. . . . . . . . . . . . . . . . . . . . .150°C
Operating Temperature Range. . . . . . . . . 0°C to 85°C
Storage Temperature Range. . . . . . . . -65°C to 160°C
Reflow Temperature (Soldering, 10 sec) . . . . . .260°C
Supply Voltage (VDD to VSS) . . . . . . . . . . . . . . . . . .6.5V
All Other Pins. . . . . . . . . . . . . (Vss-0.3V) to (VDD+0.3V)
Continuous Power Dissipation (TA=25°C)
SOP-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520mW
MSOP-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520mW
TSSOP-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 520mW
Electrical Characteristics
VDD = 5V; VSS = 0V; Tamb = 25°C; CL=10pF, RL=1kΩ to VDD/2; unless otherwise specified.
PARAMETER
SYMBOL
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Supplies
Supply Voltage Range
VDD
Note1
3
---
5.5
V
Supply Current
Total Power Dissipation
DC Characteristics
IDD
Ptot
No load
No load
-----
1
5
1.4
7
mA
mW
Input Offset Voltage
Common Mode Voltage
VI (OS)
VCM
Inferred from CMRR test
--0
±5
-
±20
5
mV
V
IB
---
±1.5
±20
nA
Input Bias Current Offset
Input Resistance
IOS
RIN
-----
±1.5
1000
±20
---
nA
MΩ
Open Loop Gain
AV
Maximum Output Current
Output Voltage Swing High
IO
VOH
Input Bias Current
85
95
---
dB
55
4.96
±66
4.99
-----
mA
V
---
0.012
0.04
V
45
42
70
65
-----
dB
dB
Output Voltage Swing Low
Power Supply Rejection Ratio
Common-Mode Rejection Ratio
AC Characteristics
VOL
PSRR
CMRR
VOUT = ±VIN x 90%
RL = 2kΩ
RL = 2kΩ
3V≦VDD≦5.5V
VSS≦VCM≦VDD
Gain-Bandwidth Product
GBWP
Open-loop; No Load
---
2.5
---
MHz
Measured from 10% to 90% of
4VP-P step, RL = 1kΩ, CL = 10pF
---
6
---
V/µs
-------
60
100
85
-------
deg
mA
dB
Slew-Rate
SR
Phase Margin
PM
Maximum Output Current with THD
Channel Separation
IO
CS
THD< 0.1%, RL = 16Ω
f = 1KHz RL = 32Ω
Note1: Guaranteed by the Power-Supply Rejection Ratio (PSRR) test
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.5
Mar 02, 2007
2
G1224
Global Mixed-mode Technology Inc.
Typical Performance Characteristics
VDD = 5V; VSS = 0V; Tamb = 25°C; CL=10pF, RL=1kΩ to VDD/2; unless otherwise specified.
Open Loop Gain & Phase Margin
vs. Frequency
100
PSRR vs. Frequency
225
90
Gain
80
180
60
135
50
40
90
Phase
30
20
PSRRPSRR (dB)
Gain(dB)
70
Phase Margin( °)
80
60
PSRR+
40
45
10
0
0
1.E-02
1.E-01
1.E+00
1.E+01
1.E+02
1.E+03
20
1.E+04
1.E-01
1.E+00
CMRR vs. Frequency
1.E+02
1.E+03
1.E+04
Total Harmonic Distortion Plus
Noise vs.Output Power
80
10
f=1kHz
Av=1
THD+N(%)
60
CMRR (dB)
1.E+01
Frequency - kHz
Frequency - kHz
40
1
RL=32Ω
RL=15Ω
0.1
20
p=(Vrms)2/R
0.01
0
1
10
100
1000
Frequency - kHz
5
10000
160
140
140
Sourcing Current(mA)
Sinking Current (mA)
65
85
105
125
Sourcing Current vs. (VDD) - Vo
Sinking Current vs. Vo - (VSS)
120
VDD=+5V
80
45
Output Power (mW)
160
100
25
VDD=+3V
60
40
20
120
100
VDD=+5V
80
VDD=+3V
60
40
20
0
0
0.1
0.6
1.1
1.6
2.1
0.1
0.6
1.1
1.6
2.1
(VDD) - Vo
Vo - (VSS)
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.5
Mar 02, 2007
3
G1224
Global Mixed-mode Technology Inc.
Typical Performance Characteristics (Continued)
Large Signal Transient Response
Small Signal Transient Response
Operation with Beyond-the Rail Input
Operation with Rail-to-Rail Input and Output
Recommended Minimum Footprint
TSSOP-8
SOP-8
MSOP-8
SOT-23-8
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.5
Mar 02, 2007
4
G1224
Global Mixed-mode Technology Inc.
Package Information
C
E
H
L
D
θ
7 °(4X)
A2
A
A1
y
e
B
SOP- 8 (P1) Package
Note:
1. Package body sizes exclude mold flash and gate burrs
2. Dimension L is measured in gage plane
3. Tolerance 0.10mm unless otherwise specified
4. Controlling dimension is millimeter converted inch dimensions are not necessarily exact.
5. Followed from JEDEC MS-012
MIN.
DIMENSION IN MM
NOM.
MAX.
MIN.
DIMENSION IN INCH
NOM.
MAX.
A
A1
1.35
0.10
1.60
-----
1.75
0.25
0.053
0.004
0.063
-----
0.069
0.010
A2
B
----0.33
1.45
-----
----0.51
----0.013
0.057
-----
----0.020
C
D
0.19
4.80
---------
0.25
5.00
0.007
0.189
---------
0.010
0.197
E
e
H
3.80
----5.80
----1.27
-----
4.00
----6.20
0.150
----0.228
----0.050
-----
0.157
----0.244
L
y
θ
0.40
-----
---------
1.27
0.10
0.016
-----
---------
0.050
0.004
0°
-----
8°
0°
-----
8°
SYMBOL
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.5
Mar 02, 2007
5
G1224
Global Mixed-mode Technology Inc.
C
E1
E
L
D
θ
12° (4X)
A2
A
A1
y
e
b
MSOP-8 (P8) Package
Note:
1. Package body sizes exclude mold flash and gate burrs
2. Dimension L is measured in gage plane
3. Tolerance 0.10mm unless otherwise specified
4. Controlling dimension is millimeter converted inch dimensions are not necessarily exact.
5. Followed from JEDEC MO-137
SYMBOL
A
A1
A2
b
C
D
E
E1
e
L
y
θ
MIN.
DIMENSION IN MM
NOM.
MAX.
MIN.
DIMENSION IN INCH
NOM.
MAX.
0.81
0.00
0.76
0.28
0.13
2.90
4.80
2.90
----0.40
----0°
1.02
----0.86
0.30
0.15
3.00
4.90
3.00
0.65
0.53
---------
1.22
0.20
0.97
0.38
0.23
3.10
5.00
3.10
----0.66
0.10
6°
0.032
0.000
0.030
0.011
0.005
0.114
0.189
0.114
----0.016
----0°
0.040
----0.034
0.012
0.006
0.118
0.193
0.118
0.026
0.021
---------
0.048
0.008
0.038
0.015
0.009
0.122
0.197
0.122
----0.026
0.004
6°
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.5
Mar 02, 2007
6
G1224
Global Mixed-mode Technology Inc.
C
L
E1
E
θ
D
12°(4X)
A2
A
A1
y
e
b
TSSOP-8 (D1) Package
Note:
1. Package body sizes exclude mold flash protrusions or gate burrs
2. Tolerance ±0.10mm unless otherwise specified
3. Coplanarity: 0.10mm
4. Controlling dimension is millimeter converted inch dimensions are not necessarily exact.
6. Followed from JEDEC MO-153
SYMBOL
A
A1
A2
b
C
D
E
E1
e
L
y
θ
MIN.
DIMENSION IN MM
NOM.
MAX.
MIN.
DIMENSION IN INCH
NOM.
MAX.
----0.05
0.80
0.19
0.09
2.90
----4.30
----0.45
----0°
--------1.00
--------3.00
6.40
4.40
0.65
0.60
---------
1.20
0.15
1.05
0.30
0.20
3.10
----4.50
----0.75
0.10
8°
----0.002
0.031
0.007
0.004
0.114
----0.169
----0.018
----0°
--------0.039
--------0.118
0.252
0.173
0.026
0.024
---------
0.048
0.006
0.041
0.012
0.008
0.122
----0.177
----0.030
0.004
8°
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.5
Mar 02, 2007
7
G1224
Global Mixed-mode Technology Inc.
e1
C
E1
E
L
D
θ
θ1
A2
e
A
A1
b
SOT-23-8 (TM) Package
SYMBOL
A
A1
A2
b
C
D
E
E1
e
e1
L
θ
θ1
MIN.
DIMENSION IN MM
NOM.
----0.00
0.90
0.22
0.08
0.30
0°
5°
--------1.15
--------2.90 BSC
2.80 BSC
1.60 BSC
0.65 BSC
1.95 BSC
0.45
4°
10°
MAX.
MIN.
1.45
0.15
1.30
0.38
0.22
----0.000
0.035
0.009
0.003
0.60
8°
15°
0.012
0°
5°
DIMENSION IN INCH
NOM.
----------------0.114 BSC
0.110 BSC
0.063 BSC
0.026 BSC
0.077 BSC
0.018
4°
10°
MAX.
0.057
0.006
0.051
0.015
0.009
0.024
8°
15°
Taping Specification
Feed Direction
Typical SOP/MSOP/TSSOP Package Orientation
Feed Direction
Typical SOT-23-8 Package Orientation
PACKAGE
Q’TY/REEL
SOP-8
MSOP-8
TSSOP-8
SOT-23-8
2,500 ea
2,500 ea
2,500 ea
3,000 ea
GMT Inc. does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and GMT Inc. reserves the right at any time without notice to change said circuitry and specifications.
TEL: 886-3-5788833
http://www.gmt.com.tw
Ver: 1.5
Mar 02, 2007
8
Similar pages