Cypress CY7C1021BV33-10VC 64k x 16 static ram Datasheet

021BV33
CY7C1021BV33
64K x 16 Static RAM
Writing to the device is accomplished by taking Chip Enable
(CE) and Write Enable (WE) inputs LOW. If Byte Low Enable
(BLE) is LOW, then data from I/O pins (I/O1 through I/O8), is
written into the location specified on the address pins (A0
through A15). If Byte High Enable (BHE) is LOW, then data
from I/O pins (I/O9 through I/O16) is written into the location
specified on the address pins (A0 through A15).
Features
• 3.3V operation (3.0V–3.6V)
• High speed
— tAA = 10/12/15 ns
• CMOS for optimum speed/power
• Low Active Power (L version)
— 576 mW (max.)
• Low CMOS Standby Power (L version)
— 1.80 mW (max.)
• Automatic power-down when deselected
• Independent control of upper and lower bits
• Available in 44-pin TSOP II and 400-mil SOJ
• Available in a 48-Ball Mini BGA package
Reading from the device is accomplished by taking Chip Enable (CE) and Output Enable (OE) LOW while forcing the Write
Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then
data from the memory location specified by the address pins
will appear on I/O1 to I/O8. If Byte High Enable (BHE) is LOW,
then data from memory will appear on I/O9 to I/O16. See the
truth table at the back of this data sheet for a complete description of read and write modes.
Functional Description[1]
The CY7C1021BV is a high-performance CMOS static RAM
organized as 65,536 words by 16 bits. This device has an automatic power-down feature that significantly reduces power
consumption when deselected.
The input/output pins (I/O1 through I/O16) are placed in a
high-impedance state when the device is deselected
(CE HIGH), the outputs are disabled (OE HIGH), the BHE and
BLE are disabled (BHE, BLE HIGH), or during a write operation (CE LOW, and WE LOW).
The CY7C1021BV is available in 400-mil-wide SOJ, standard
44-pin TSOP Type II, and 48-ball mini BGA packages.
Logic Block Diagram
Pin Configurations
SOJ / TSOP II
Top View
SENSE AMPS
A7
A6
A5
A4
A3
A2
A1
A0
ROW DECODER
DATA IN DRIVERS
64K x 16
RAM Array
512 X 2048
A4
A3
A2
A1
A0
CE
I/O1
I/O2
I/O3
I/O4
VCC
VSS
I/O5
I/O6
I/O7
I/O8
WE
A15
A14
A13
A12
NC
I/O1–I/O8
I/O9–I/O16
COLUMN DECODER
A8
A9
A10
A11
A12
A13
A14
A15
BHE
WE
CE
OE
BLE
1
44
2
3
43
42
4
41
40
39
38
5
6
7
8
9
10
11
12
37
36
35
34
33
32
31
30
29
28
27
13
14
15
16
17
18
19
20
21
22
26
25
24
23
A5
A6
A7
OE
BHE
BLE
I/O16
I/O15
I/O14
I/O13
VSS
VCC
I/O12
I/O11
I/O10
I/O9
NC
A8
A9
A10
A11
NC
Selection Guide
7C1021BV-8
7C1021BV-10
7C1021BV-12
7C1021BV-15
8
10
12
15
Commercial
170
160
150
140
Industrial
190
180
170
160
Maximum Access Time (ns)
Maximum Operating Current (mA)
Maximum CMOS Standby Current
(mA)
Commercial
L
5
5
5
5
0.500
0.500
0.500
0.500
Shaded areas contain advance information.
Note:
1. For guidelines on SRAM system design, please refer to the ‘System Design Guidelines’ Cypress application note, available on the internet at www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05148 Rev. *A
•
3901 North First Street
•
San Jose
•
CA 95134 • 408-943-2600
Revised September 13, 2002
CY7C1021BV33
Pin Configurations
Mini BGA
(Top View)
1
2
3
4
5
6
BLE
OE
A0
A1
A2
NC
A
I/O9 BHE
A3
A4
CE
I/O1
B
I/O10 I/O11
A5
A6
I/O2
I/O3
C
VSS I/O12 NC
A7
I/O4 VCC
D
VCC I/O13 NC
NC
I/O5
VSS
E
I/O15 I/O14 A14
A15 I/O6
I/O7
F
I/O16 NC
NC
A8
A12
A13
WE I/O8
G
A9
A10
A11
H
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
Storage Temperature ................................. –65°C to +150°C
Ambient Temperature with
Power Applied............................................. –55°C to +125°C
Supply Voltage on VCC to Relative GND[2] .... –0.5V to +4.6V
DC Voltage Applied to Outputs
in High Z State[2] ......................................–0.5V to VCC+0.5V
DC Input Voltage[2]...................................–0.5V to VCC+0.5V
NC
Current into Outputs (LOW) ........................................ 20 mA
Static Discharge Voltage............................................ >2001V
(per MIL-STD-883, Method 3015)
Latch-Up Current..................................................... >200 mA
Operating Range
Range
Commercial
Industrial
Ambient Temperature
VCC
0°C to +70°C
3.3V ± 10%
–40°C to +85°C
3.3V ± 10%
Note:
2. Mimimum voltage is–2.0V for pulse durations of less than 20 ns.
Document #: 38-05148 Rev. *A
Page 2 of 11
CY7C1021BV33
Electrical Characteristics Over the Operating Range
Parameter
Description
Test Conditions
7C1021BV-8
7C1021BV-10
7C1021BV-12
Min.
Min.
Min.
Max.
2.4
Max.
2.4
Max.
VOH
Output HIGH
Voltage
VCC = Min.,
IOH = –4.0 mA
2.4
VOL
Output LOW
Voltage
VCC = Min., IOL = 8.0 mA
VIH
Input HIGH
Voltage
2.2
VCC+
0.3V
2.2
VCC+
0.3V
2.2
VCC+
0.3V
VIL
Input LOW
Voltage[2]
−0.3
0.8
−0.3
0.8
–0.3
IIX
Input Load
Current
GND < VI < VCC
−1
+1
−1
+1
IOZ
Output Leakage
Current
GND < VI < VCC,
Output Disabled
−1
+1
−1
+1
ICC
VCC Operating
Supply Current
VCC = Max.,
IOUT = 0 mA,
f = fMAX = 1/tRC
ISB1
Automatic CE
Power-Down
Current
—TTL Inputs
ISB2
Automatic CE
Power-Down
Current
—CMOS Inputs
0.4
7C1021BV-15
Min.
Max.
2.4
0.4
0.4
Unit
V
0.4
V
2.2
VCC+
0.3V
V
0.8
–0.3
0.8
V
–1
+1
–1
+1
µA
–1
+1
–1
+1
µA
Com
170
160
150
140
mA
Ind
190
120
170
160
mA
Max. VCC,
CE > VIH
VIN > VIH or
VIN < VIL, f = fMAX
40
40
40
40
mA
Max. VCC,
CE > VCC – 0.3V, L
VIN > VCC – 0.3V,
or VIN < 0.3V,
f=0
5
5
5
5
mA
500
500
500
500
µA
Shaded areas contain advance information.
Capacitance[3]
Parameter
Description
CIN
Input Capacitance
COUT
Output Capacitance
Test Conditions
TA = 25°C, f = 1 MHz
Max.
Unit
6
pF
8
pF
Note:
3. Tested initially and after any design or process changes that may affect these parameters.
AC Test Loads and Waveforms
R 317Ω
R 317Ω
3.3V
3.3V
OUTPUT
90%
OUTPUT
30 pF
R2
351Ω
INCLUDING
JIG AND
SCOPE
(a)
Document #: 38-05148 Rev. *A
R2
351Ω
5 pF
INCLUDING
JIG AND
SCOPE
167
OUTPUT
Equivalent to: THÉVENIN
EQUIVALENT
ALL INPUT PULSES
3.0V
GND
Rise Time: 1 V/ns
(b)
10%
90%
10%
Fall Time: 1 V/ns
1.73V
30 pF
Page 3 of 11
CY7C1021BV33
Switching Characteristics[4] Over the Operating Range
Parameter
Description
7C1021BV-8
7C1021BV-10
7C1021BV-12
7C1021BV-15
Min.
Min.
Min.
Min.
Max.
Max.
Max.
Max.
Unit
READ CYCLE
tRC
Read Cycle Time
tAA
Address to Data Valid
8
tOHA
Data Hold from Address Change
tACE
CE LOW to Data Valid
8
10
12
15
ns
tDOE
OE LOW to Data Valid
4
4
6
7
ns
tLZOE
OE LOW to Low Z
3
OE HIGH to High Z
tLZCE
CE LOW to Low Z[6]
4
tHZCE
CE HIGH to High Z
tPU
CE LOW to Power-Up
tPD
CE HIGH to Power-Down
tDBE
Byte Enable to Data Valid
4
tLZBE
Byte Enable to Low Z
0
tHZBE
Byte Disable to High Z
3
6
3
12
ns
ns
7
ns
0
12
12
5
4
ns
7
6
0
6
0
ns
3
5
0
ns
0
5
4
ns
15
3
0
3
0
15
12
0
3
[5, 6]
12
10
3
0
[5, 6]
tHZOE
WRITE
10
8
0
ns
15
ns
7
ns
0
5
6
ns
7
ns
CYCLE[7]
tWC
Write Cycle Time
8
10
12
15
ns
tSCE
CE LOW to Write End
7
8
9
10
ns
tAW
Address Set-Up to Write End
6
7
8
10
ns
tHA
Address Hold from Write End
0
0
0
0
ns
tSA
Address Set-Up to Write Start
0
0
0
0
ns
tPWE
WE Pulse Width
6
8
8
10
ns
tSD
Data Set-Up to Write End
4
6
6
8
ns
tHD
Data Hold from Write End
0
0
0
0
ns
tLZWE
WE HIGH to Low Z[6]
3
3
3
3
ns
Z[5, 6]
tHZWE
WE LOW to High
tBW
Byte Enable to End of Write
4
8
5
8
6
8
7
ns
9
ns
Shaded areas contain advance information.
Data Retention Characteristics Over the Operating Range (L version only)
Parameter
Conditions[8]
Description
VDR
VCC for Data Retention
ICCDR
Data Retention Current
tCDR[9]
Chip Deselect to Data Retention Time
tR[10]
Operation Recovery Time
Min.
Max.
2.0
Com’l
VCC = VDR = 2.0V,
CE > VCC – 0.3V,
VIN > VCC – 0.3V or VIN < 0.3V
Unit
V
100
µA
0
ns
tRC
ns
Notes:
4. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified
IOL/IOH and 30-pF load capacitance.
5. tHZOE, tHZBE, tHZCE, and tHZWE are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage.
6. At any given temperature and voltage condition, tHZCE is less than tLZCE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any given device.
7. The internal write time of the memory is defined by the overlap of CE LOW, WE LOW and BHE / BLE LOW. CE, WE and BHE / BLE must be LOW to initiate a write,
and the transition of these signals can terminate the write. The input data set-up and hold timing should be referenced to the leading edge of the signal that terminates the write.
8. No input may exceed VCC + 0.5V.
9. Tested initially and after any design or process changes that may affect these parameters.
10. tr < 3 ns for the -12 and -15 speeds. tr < 5 ns for the -20 and slower speeds.
Document #: 38-05148 Rev. *A
Page 4 of 11
CY7C1021BV33
Data Retention Waveform
DATA RETENTION MODE
3.0V
VCC
VDR > 2V
3.0V
tR
tCDR
CE
Switching Waveforms
Read Cycle No. 1
[11, 12]
tRC
ADDRESS
tAA
tOHA
DATA OUT
PREVIOUS DATA VALID
Read Cycle No. 2 (OE Controlled)
DATA VALID
[12, 13]
ADDRESS
tRC
CE
tACE
OE
tHZOE
tDOE
BHE, BLE
tLZOE
tHZCE
tDBE
tLZBE
DATA OUT
HIGH IMPEDANCE
tLZCE
VCC
SUPPLY
CURRENT
tHZBE
HIGH
IMPEDANCE
DATA VALID
tPD
tPU
50%
IICC
CC
50%
IISB
SB
Notes:
11. Device is continuously selected. OE, CE, BHE and/or BHE = VIL.
12. WE is HIGH for read cycle.
13. Address valid prior to or coincident with CE transition LOW.
Document #: 38-05148 Rev. *A
Page 5 of 11
CY7C1021BV33
Switching Waveforms (continued)
Write Cycle No. 1 (CE Controlled)
[14, 15]
tWC
ADDRESS
CE
tSA
tSCE
tAW
tHA
tPWE
WE
tBW
BHE, BLE
tSD
tHD
DATA I/O
Write Cycle No. 2 (BLE or BHE Controlled)
tWC
ADDRESS
BHE, BLE
tSA
tBW
tAW
tHA
tPWE
WE
tSCE
CE
tSD
tHD
DATA I/O
Notes:
14. Data I/O is high impedance if OE or BHE and/or BLE= VIH.
15. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high-impedance state.
Document #: 38-05148 Rev. *A
Page 6 of 11
CY7C1021BV33
Switching Waveforms (continued)
Write Cycle No. 3 (WE Controlled, LOW)
tWC
ADDRESS
tSCE
CE
tAW
tHA
tSA
tPWE
WE
tBW
BHE, BLE
tHZWE
tSD
tHD
DATA I/O
tLZWE
Truth Table
CE
OE
WE
BLE
BHE
H
X
X
X
X
High Z
High Z
Power-Down
Standby (ISB)
L
L
H
L
L
Data Out
Data Out
Read - All bits
Active (ICC)
L
H
Data Out
High Z
Read - Lower bits only
Active (ICC)
H
L
High Z
Data Out
Read - Upper bits only
Active (ICC)
L
L
Data In
Data In
Write - All bits
Active (ICC)
L
H
Data In
High Z
Write - Lower bits only
Active (ICC)
H
L
High Z
Data In
Write - Upper bits only
Active (ICC)
L
X
L
I/O1–I/O8
I/O9–I/O16
Mode
Power
L
H
H
X
X
High Z
High Z
Selected, Outputs Disabled
Active (ICC)
L
X
X
H
H
High Z
High Z
Selected, Outputs Disabled
Active (ICC)
Document #: 38-05148 Rev. *A
Page 7 of 11
CY7C1021BV33
Ordering Information
Speed (ns)
8
Ordering Code
CY7C1021BV33-8BAC
12
48-Ball Mini Ball Grid Array (7.00 mm x 7.00 mm)
V34
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33L-8VC
V34
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33-8ZC
Z44
44-Lead TSOP Type II
Z44
44-Lead TSOP Type II
CY7C1021BV33-10BAC
BA48A
48-Ball Mini Ball Grid Array (7.00 mm x 7.00 mm)
CY7C1021BV33-10VC
V34
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33L-10VC
V34
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33-10ZC
Z44
44-Lead TSOP Type II
CY7C1021BV33L-10ZC
Z44
44-Lead TSOP Type II
CY7C1021BV33-12BAC
BA48A
48-Ball Mini Ball Grid Array (7.00 mm x 7.00 mm)
CY7C1021BV33-12VC
V34
CY7C1021BV33L-12VC
V34
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33-12ZC
Z44
44-Lead TSOP Type II
CY7C1021BV33L-12ZC
Z44
44-Lead TSOP Type II
CY7C1021BV33-12BAI
BA48A
CY7C1021BV33-12VI
15
BA48A
Package Type
CY7C1021BV33-8VC
CY7C1021BV33L-8ZC
10
Package
Name
V34
Operating
Range
Commercial
Commercial
Commercial
44-Lead (400-Mil) Molded SOJ
48-Ball Mini Ball Grid Array (7.00 mm x 7.00 mm)
Industrial
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33-15BAC
BA48A
48-Ball Mini Ball Grid Array (7.00 mm x 7.00 mm)
CY7C1021BV33L-15BAC
BA48A
48-Ball Mini Ball Grid Array (7.00 mm x 7.00 mm)
CY7C1021BV33-15VC
V34
CY7C1021BV33L-15VC
V34
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33-15ZC
Z44
44-Lead TSOP Type II
CY7C1021BV33L-15VC
Z44
44-Lead TSOP Type II
CY7C1021BV33-15BAI
BA48A
48-Ball Mini Ball Grid Array (7.00 mm x 7.00 mm)
CY7C1021BV33L-15BAI
BA48A
48-Ball Mini Ball Grid Array (7.00 mm x 7.00 mm)
Commercial
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33-15VI
V34
44-Lead (400-Mil) Molded SOJ
CY7C1021BV33L-15ZI
Z44
44-Lead TSOP Type II
Industrial
Shaded areas contain advance information.
Document #: 38-05148 Rev. *A
Page 8 of 11
CY7C1021BV33
Package Diagrams
48-Ball (7.00 mm x 7.00 mm x 1.2 mm) FBGA BA48A
51-85096-*E
Document #: 38-05148 Rev. *A
Page 9 of 11
CY7C1021BV33
Package Diagrams (continued)
44-Lead (400-Mil) Molded SOJ V34
51-85082-*B
44-Pin TSOP II Z44
51-85087-A
All product and company names mentioned in this document may be the trademarks of their respective holders.
Document #: 38-05148 Rev. *A
Page 10 of 11
© Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize
its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges.
CY7C1021BV33
Document History Page
Document Title: CY7C1021BV33 64K x 16 Static RAM
Document Number: 38-05148
REV.
ECN NO.
Issue
Date
Orig. of
Change
Description of Change
**
109892
09/22/01
SZV
Change from Spec number: 38-00954 to 38-05148
*A
116474
09/16/02
CEA
Add applications foot note to data sheet, page 1.
Document #: 38-05148 Rev. *A
Page 11 of 11
Similar pages