LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Full-Bridge PWM Controller with Integrated MOSFET Drivers Check for Samples: LM5045 FEATURES DESCRIPTION • The LM5045 PWM controller contains all of the features necessary to implement Full-Bridge topology power converters using either current mode or voltage mode control. This device is intended to operate on the primary side of an isolated dc-dc converter with input voltage up to 100V. This highly integrated controller-driver provides dual 2A high and low side gate drivers for the four external brige MOSFETs plus control signals for the secondary side synchronous rectifier MOSFETs. External resistors program the leading and trailing edge dead-time between the main and synchronous rectifier control signals. Intelligent startup of the synchronous rectifiers allows monotonic turn-on of the power converter even with pre-bias load conditions. Additional features include cycle-by-cycle current limiting, hiccup mode restart, programmable softstart, synchronous rectifier soft-start and a 2 MHz capable oscillator with synchronization capability and thermal shutdown. 1 2 • • • • • • • • • • Highest Integration Controller for Small Form Factor, High Density Power Converters High Voltage Start-up Regulator Intelligent Sync Rectifier Start-up Allows Linear Turn-on into Pre-biased Loads Synchronous Rectifiers Disabled in UVLO mode and Hiccup Mode Two Independent, Programmable Synchronous Rectifier dead-time Adjustments Four High Current 2A Bridge Gate Drivers Wide-Bandwidth Opto-coupler Interface Configurable for either Current Mode or Voltage Mode Control Dual-mode Over-Current Protection Resistor Programmed 2MHz Oscillator Programmable Line UVLO and OVP PACKAGES • • HTSSOP 28 pin WQFN 28 pin (5mm x 5mm) Simplified Full-Bridge Power Converter Vin Vout T1 T1 VCC VCC BST1 HS1 LO1 HO1 VIN SLOPE RAMP CS LO2 HS2 BST2 HO2 SR1 UVLO SR2 LM5045 FULL-BRIDGE CONTROLLER WITH INTEGRATED GATE DRIVERS OVP VCC COMP SSOFF RT RES SS SSSR RD1 RD2 GATE DRIVE ISOLATION ISOLATED FEEDBACK REF PGND AGND ISOLATION BOUNDARY 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2011–2013, Texas Instruments Incorporated LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com Connection Diagram UVLO VIN OVP HS1 RAMP HO1 BST1 CS SLOPE SR1 COMP LO1 REF PGND HTSSOP28 RT VCC AGND LO2 RD1 SR2 RD2 BST2 HO2 RES HS2 SS SSSR SS OFF Figure 1. Top View HTSSOP Package Number PWP0028A HO1 HS1 VIN UVLO OVP RAMP CS SLOPE BST1 COMP SR1 LO1 REF 5 mm x 5 mm PGND WQFN 28 RT AGND VCC RD1 LO2 RD2 SR2 BST2 HO2 HS2 SS OFF SSSR SS RES Figure 2. Top View WQFN Package Package Number RSG0028A 2 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 PIN DESCRIPTIONS HTSSOP Pin WQFN Pin Name 1 25 UVLO 2 26 OVP/OTP 3 27 RAMP 4 28 CS 5 1 6 Description Application Information Line Under-Voltage Lockout An external voltage divider from the power source sets the shutdown and standby comparator levels. When UVLO reaches the 0.4V threshold the VCC and REF regulators are enabled. At the 1.25V threshold, the SS pin is released and the controller enters the active mode. Hysteresis is set by an internal current sink that pulls 20µA from the external resistor divider. Over Voltage Protection An external voltage divider from the input power supply sets the shutdown level during an over-voltage condition. Alternatively, an external NTC thermistor voltage divider can be used to set the shutdown temperature. The threshold is 1.25V. Hysteresis is set by an internal current that sources 20 µA of current into the external resistor divider. Input to PWM Comparator Modulation ramp for the PWM comparator. This ramp can be a signal representative of the primary current (current mode) or proportional to the input voltage (feed-forward voltage mode). This pin is reset to GND at the end of every cycle. Current Sense Input If CS exceeds 750mV the PWM output pulse will be terminated, entering cycle-by-cycle current limit. An internal switch holds CS low for 40nS after either output switches high to blank leading edge transients. SLOPE Slope Compensation Current A ramping current source from 0 to 100µA is provided for slope compensation in current mode control. This pin can be connected through an appropriate resistor to the CS pin to provide slope compensation. If slope compensation is not required, SLOPE must be tied to ground. 2 COMP Input to the Pulse Width Modulator An external opto-coupler connected to the COMP pin sources current into an internal NPN current mirror. The PWM duty cycle is at maximum with zero input current, while 1mA reduces the duty cycle to zero. The current mirror improves the frequency response by reducing the AC voltage across the opto-coupler. 7 3 REF Output of a 5V reference Maximum output current is 15mA. Locally decouple with a 0.1µF capacitor. 8 4 RT/SYNC Oscillator Frequency Control and Frequency Synchronization The resistance connected between RT and AGND sets the oscillator frequency. Synchronization is achieved by AC coupling a pulse to the RT/SYNC pin that raises the voltage at least 1.5V above the 2V nominal bias level. 9 5 AGND Analog Ground Connect directly to the Power Ground. 10 6 RD1 Synchronous Rectifier Leading Edge Delay The resistance connected between RD1 and AGND sets the delay from the falling edge of SR1 or SR2 and the rising edge of HO2/LO1 or HO1/LO2 respectively. 11 7 RD2 Synchronous Rectifier Trailing Edge Delay The resistance connected between RD2 and AGND sets the delay from the falling edge of HO1/LO2 or HO2/LO1 and the rising edge of SR2 or SR1 respectively. 12 8 RES Restart Timer Whenever the CS pin exceeds the 750mV cycle-cycle current limit threshold, 30µA current is sourced into the RES capacitor for the remainder of the PWM cycle. If the RES capacitor voltage reaches 1.0V, the SS capacitor is discharged to disable the HO1, HO2, LO1, LO2 and SR1, SR2 outputs. The SS pin is held low until the voltage on the RES capacitor has been ramped between 2V and 4V eight times by 10µA charge and 5µA discharge currents. After the delay sequence, the SS capacitor is released to initiate a normal start-up sequence. 13 9 SS Soft-Start Input An internal 20µA current source charges the SS pin during start-up. The input to the PWM comparator gradually rises as the SS capacitor charges to steadily increase the PWM duty cycle. Pulling the SS pin to a voltage below 200mV stops PWM pulses at HO1,2 and LO1,2 and turns off the synchronous rectifier FETs to a low state. 14 10 SSSR Secondary Side Soft-Start An external capacitor and an internal 20µA current source set the soft-start ramp for the synchronous rectifiers. The SSSR capacitor charge-up is enabled after the first output pulse and SS>2V and Icomp <800µA Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 3 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com PIN DESCRIPTIONS (continued) HTSSOP Pin WQFN Pin Name 15 11 SSOFF 19 15 21 17 Description Application Information Soft-Stop Disable When SS OFF pin is connected to the AGND, the LM5045 softstops in the event of a VIN UVLO and Hiccup mode current limit condition. If the SSOFF pin is connected to REF pin, the controller hard-stops on any fault condition. Refer Table 1 for more details. SR2 Synchronous Rectifier Driver Control output for synchronous rectifier gate. Capable of peak sourcing 100mA and sinking 400mA. VCC Output of Start-Up Regulator The output voltage of the start-up regulator is initially regulated to 9.5V. Once the secondary side soft-start (SSSR pin) reaches 1V, the VCC output is reduced to 7.7V. If an auxiliary winding raises the voltage on this pin above the regulation set-point, the internal startup regulator will shutdown, thus reducing the IC power dissipation. Power Ground Connect directly to Analog Ground Low Side Output Driver Alternating output of the PWM gate driver. Capable of 1.5A peak source and 2A peak sink current. Synchronous Rectifier Driver Control output for synchronous rectifier gate. Capable of peak sourcing 100mA and sinking 400mA. 22 18 PGND 23, 20 19, 16 LO1, LO2 24 20 SR1 25, 18 21, 14 BST1,2 Gate Drive Bootstrap Bootstrap capacitors connected between BST1,2 and SW1,2 provide bias supply for the high side HO1,2 gate drivers. External diodes are required between VCC and BST1,2 to charge the bootstrap capacitors when SW1,2 are low. 26, 17 22, 13 HO1,2 High Side Output Driver High side PWM outputs capable of driving the upper MOSFET of the bridge with 1.5A peak source and 2A peak sink current. 27, 16 23, 12 HS1,2 Switch Node Common connection of the high side FET source, low side FET drain and transformer primary winding. 28 24 VIN Input Power Source Input to the Start-up Regulator. Operating input range is 14V to 100V. For power sources outside of this range, the LM5045 can be biased directly at VCC by an external regulator. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 4 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Absolute Maximum Ratings (1) VIN to GND -0.3V to 105V HS to GND (2) -5V to 105V BST1/BST2 to GND -0.3V to 116V BST1/BST2 to HS1/HS2 HO1/HO2 to HS1/HS2 -0.3V to 16V (3) -0.3V to BST1/BST2+0.3V LO1/LO2/SR1/SR2 (3) -0.3V to VCC+0.3V VCC to GND -0.3V to 16V REF,SSOFF,RT,OVP,UVLO to GND -0.3V to 7V RAMP -0.3V to 7V COMP -0.3V COMP Input Current +10mA All other inputs to GND (3) -0.3 to REF+0.3V ESD Rating HBM (4) 2 kV Storage Temperature Range -55°C to 150°C Junction Temperature 150°C (1) (2) (3) (4) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For ensured specifications and test conditions, see the Electrical Characteristics. The negative HS voltage must never be more negative than VCC-16V. For example, if VCC=12V, the negative transients at HS must not exceed -4V. These pins are output pins and as such should not be connected to an external voltage source. The voltage range listed is the limits the internal circuitry is designed to reliably tolerate in the application circuit. The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin. Operating Ratings (1) VIN Voltage 14V to 100V External Voltage Applied to VCC 10V to 14V Junction Temperature -40°C to +125°C SLOPE (1) -0.3V to 2V Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For ensured specifications and test conditions, see the Electrical Characteristics. Electrical Characteristics Limits in standard typeface are for TJ = 25°C only; limits in boldface type apply the junction temperature range of -40°C to +125°C. Unless otherwise specified, the following conditions apply: VIN = 48V, RT = 25kΩ, RD1=RD2=20kΩ. No load on HO1, HO2, LO1, LO2, SR1, SR2, COMP=0V, UVLO=2.5V, OVP=0V, SSOFF=0V. Symbol Parameter Conditions Min Typ Max Units V Startup Regulator (VCC pin) VCC1 VCC voltage ICC= 10mA (SSSR<1V) 9.3 9.6 9.9 VCC2 VCC voltage ICC= 10mA (SSSR>1V) 7.5 7.8 8.1 ICC(Lim) VCC current limit VCC= 6V 60 80 mA ICC(ext) VCC supply current Supply current into VCC from an externally applied source. VCC = 10V 4.6 mA VCC load regulation ICC from 0 to 50 mA 35 mV VCC under-voltage threshold Positive going VCC VCC under-voltage threshold Negative going VCC VCC(UV) IIN VIN operating current VIN shutdown current VIN start-up regulator leakage VCC1–0. VCC1–0. 2 1 5.9 6.3 V V 6.7 4 V mA VIN=20V, VUVLO=0V 300 520 µA VVIN=100V, VUVLO=0V 350 550 µA VCC=10V 160 µA Voltage Reference Regulator (REF pin) Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 5 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com Electrical Characteristics (continued) Limits in standard typeface are for TJ = 25°C only; limits in boldface type apply the junction temperature range of -40°C to +125°C. Unless otherwise specified, the following conditions apply: VIN = 48V, RT = 25kΩ, RD1=RD2=20kΩ. No load on HO1, HO2, LO1, LO2, SR1, SR2, COMP=0V, UVLO=2.5V, OVP=0V, SSOFF=0V. Symbol Parameter Conditions Min Typ Max REF Voltage IREF = 0mA 4.85 5 5.15 V REF voltage regulation IREF = 0 to 10mA 25 50 mV IREF(Lim) REF current limit VREF = 4.5V 15 20 VREFUV VREF under-voltage threshold Positive going VREF 4.3 4.5 VREF Hysteresis Units mA 4.7 0.25 V V Under-Voltage Lock Out and shutdown (UVLO pin) VUVLO Under-voltage threshold IUVLO Hysteresis current UVLO pin sinking current when VUVLO<1.25V Under-voltage standby enable threshold UVLO voltage rising 1.18 1.25 1.32 V 16 20 24 µA 0.32 0.4 0.48 V Hysteresis VOVP 0.05 V OVP shutdown threshold OVP rising 1.18 1.25 1.32 V OVP hysteresis current OVP sources current when OVP>1.25V 16 20 24 µA VSS = 0V 16 20 24 µA 1.93 2.0 2.20 V Soft-Start (SS Pin) ISS SS charge current SS threshold for SSSR charge current ICOMP<800µA enable SS output low voltage Sinking 100µA 40 SS threshold to disable switching ISSSR mV 200 mV SSSR charge current VSS>2V, ICOMP<800µA 16 20 24 µA ISSSR-DIS1 SSSR discharge current 1 VUVLO<1.25V 54 65 75 µA ISSSR-DIS2 SSSR discharge current 2 VRES>1V 109 125 147 µA SSSR output low voltage Sinking 100µA SSSR threshold to enable SR1/SR2 50 mV 1.2 V Current Sense Input (CS Pin) VCS RCS Current limit threshold 0.710 0.750 0.785 V CS delay to output 65 ns CS leading edge blanking 50 ns CS sink impedance (clocked) Internal FET sink impedance 18 45 Ω Soft-Stop Disable (SS OFF Pin) VIH(min) SSOFF Input-threshold 2.8 V SSOFF pull down resistance 200 kΩ Current Limit Restart (RES Pin) RRES RES pull-down resistance 37 Ω VRES RES hiccup threshold 1 V RES upper counter threshold 4 V RES lower counter threshold 2 V Termination of hiccup timer IRES-SRC1 Charge current source 1 VRES<1V,VCS>750mV 30 µA IRES-SRC2 Charge current source 2 1V<VRES<4V 10 µA IRES-DIS2 Discharge current source 1 VCS<750mV 5 µA IRES-DIS2 Discharge current source 2 2V<VRES<4V 5 µA Ratio of time in hiccup mode to time in current limit VRES>1V, Hiccup counter 147 Voltage Feed-Forward (RAMP Pin) RAMP sink impedance (Clocked) 6 5.5 Submit Documentation Feedback 20 Ω Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Electrical Characteristics (continued) Limits in standard typeface are for TJ = 25°C only; limits in boldface type apply the junction temperature range of -40°C to +125°C. Unless otherwise specified, the following conditions apply: VIN = 48V, RT = 25kΩ, RD1=RD2=20kΩ. No load on HO1, HO2, LO1, LO2, SR1, SR2, COMP=0V, UVLO=2.5V, OVP=0V, SSOFF=0V. Symbol Parameter Conditions Min Typ Max Units Oscillator (RT Pin) FSW1 Frequency (LO1, half oscillator frequency) RT = 25 kΩ 185 200 215 kHz FSW2 Frequency (LO1, half oscillator frequency) RT = 10 kΩ 420 480 540 kHz DC level 2.0 RT sync threshold V 2.8 3 3.3 V RD1=20 kΩ 45 65 90 ns RD1=100 kΩ 232 300 388 ns RD2=20 kΩ 43 65 90 ns RD2=100 kΩ 227 300 384 ns 800 940 µA 1.0 1.22 Synchronous Rectifier Timing Control (RD1 & RD2 Pins) T1 SR trailing edge delay SR turn-off to HO&LO both on T2 SR leading edge HO or LO turn-off to SR turn-on Comp Pin VPWM-OS COMP current to RAMP offset VRAMP=0V 680 VSS-OS SS to RAMP offset VRAMP=0V 0.78 COMP current to RAMP gain ΔRAMP/ΔICOMP SS to RAMP gain ΔSS/ΔRAMP COMP current for SSSR charge current enable VSS > 2V 0.5 690 COMP to output delay Minimum duty cycle V Ω 2400 800 915 120 ICOMP = 1mA µA ns 0 % Slope Compensation (SLOPE Pin) ISLOPE Slope compensation current ramp Peak of RAMP current 100 µA BOOST (BST Pin) VBst uv BST under-voltage threshold VBST-VHS rising Hysteresis 3.8 4.7 5.6 0.5 V V HO1, HO2, LO1, LO2 Gate Drivers VOL Low-state output voltage IHO/LO = 100mA 0.16 0.32 V VOH High-state output voltage IHO/LO = 100mA VOHL = VCC-VLO VOHH = VBST-VHO 0.27 0.495 V Rise Time C-load = 1000pF 16 Fall Time C-load = 1000pF 11 IOHL Peak Source Current VHO/LO = 0V 1.5 - A IOLL Peak Sink Current VHO/LO = VCC 2 - A ns ns SR1, SR2 Gate Drivers VOL Low-state output voltage ISR1/SR2 = 10mA 0.05 0.1 V VOH High-state output voltage ISR1/SR2 = 10mA, VOH = VREF-VSR 0.17 0.28 V Rise Time C-load = 1000pF 60 ns Fall Time C-load = 1000pF 20 ns IOHL Peak Source Current VSR = 0V 0.1 - A IOLL Peak Sink Current VSR = VREF 0.4 - A Thermal TSD Thermal Shutdown Temp 160 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 °C 7 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com Electrical Characteristics (continued) Limits in standard typeface are for TJ = 25°C only; limits in boldface type apply the junction temperature range of -40°C to +125°C. Unless otherwise specified, the following conditions apply: VIN = 48V, RT = 25kΩ, RD1=RD2=20kΩ. No load on HO1, HO2, LO1, LO2, SR1, SR2, COMP=0V, UVLO=2.5V, OVP=0V, SSOFF=0V. Symbol Parameter Conditions Thermal Shutdown Hysteresis (1) 8 RJA Junction to Ambient (1) RJC Junction to Case HTSSOP/WQFN Min Typ Max Units 25 °C 40 °C/W 4 °C/W 4 layer standard thermal test board. Cu thickness of layers (2oz, 1oz, 1oz, 2oz). Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Typical Performance Characteristics Application Board Efficiency VCC vs ICC 100 36V EFFICIENCY (%) 90 48V 80 72V VOUT= 3.3V 70 60 50 5 10 15 20 25 LOAD CURRENT (A) 30 Figure 3. Figure 4. VVCC and VREF vs. VVIN IIN vs. VIN 6 5 VUVLO=3V IIN(V) 4 3 VUVLO=1V 2 1 VUVLO=0V 0 0 20 40 60 VIN(V) 80 Figure 5. Figure 6. VREF vs. IREF Oscillator Frequency vs. RT Figure 7. Figure 8. 100 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 9 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Dead-Time T1, T2 vs. RD1, RD2 Dead-Time T1, T2 vs. Temperature DEAD-TIME T1,T2 (ns) 75 70 T2 65 T1 60 55 -50 Figure 9. 0 50 100 TEMPERATURE(°C) 150 Figure 10. CS Threshold vs. Temperature Figure 11. 10 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Block Diagram VOLTAGE REGULATOR VIN 1.25V VCC + OVP UVLO 0.4V VCC UVLO 20 PA - 5V HYSTERESIS + SHUTDOWN + 1.25V REF 5V REFERENCE BST1 LOGIC HO1 THERMAL LIMIT (160°C) STANDBY HS1 - VCC UVLO HYSTERESIS LO1 20 PA BST2 CLK HO2 RT DELAY OSCILLATOR Q TIMERS Q AND Q DRIVER T S 100 PA HS2 VCC LO2 LOGIC R REF 0 PA SR1 SLOPE REF SLOPECOMP RAMP GENERATOR SR2 RD1 RD2 SSOFF RAMP 20 PA SSSR 5V 5k COMP 1V + PWM - R DRIVER LOGIC SS 20 PA SS R 1:1 SS SS Buffer 0.75V CS - 10 PA CS + HICCUP MODE TIMER and LOGIC CLK + LEB PGND 30 PA RES 5 PA + AGND - 1.0V Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 11 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com FUNCTIONAL DESCRIPTION The LM5045 PWM controller contains all of the features necessary to implement a Full-Bridge topology power converter using either current mode or voltage mode control. This device is intended to operate on the primary side of an isolated dc-dc converter with input voltage up to 100V. This highly integrated controller-driver provides dual 2A high and low side gate drivers for the four external bridge MOSFETs plus control signals for secondary side synchronous rectifiers. External resistors program the leading and trailing edge dead-time between the main and synchronous rectifier control signals. Intelligent startup of synchronous rectifier allows turn-on of the power converter into the pre-bias loads. Cycle-by-cycle current limit protects the power components from load transients while hiccup mode protection limits average power dissipation during extended overload conditions. Additional features include programmable soft-start, soft-start of the synchronous rectifiers, and a 2 MHz capable oscillator with synchronization capability and thermal shutdown. High-Voltage Start-Up Regulator The LM5045 contains an internal high voltage start-up regulator that allows the input pin (VIN) to be connected directly to the supply voltage over a wide range from 14V to 100V. The input can withstand transients up to 105V. When the UVLO pin potential is greater than 0.4V, the VCC regulator is enabled to charge an external capacitor connected to the VCC pin. The VCC regulator provides power to the voltage reference (REF) and the gate drivers (HO1/HO2 and LO1/LO2). When the voltage on the VCC pin exceeds its Under Voltage (UV) threshold, the internal voltage reference (REF) reaches its regulation set point of 5V and the UVLO voltage is greater than 1.25V, the soft-start capacitor is released and normal operation begins. The regulator output at VCC is internally current limited. The value of the VCC capacitor depends on the total system design, and its start-up characteristics. The recommended range of values for the VCC capacitor is 0.47μF to 10µF. The internal power dissipation of the LM5045 can be reduced by powering VCC from an external supply. The output voltage of the VCC regulator is initially regulated to 9.5V. After the synchronous rectifiers are engaged (which is approximately when the output voltage in within regulation), the VCC voltage is reduced to 7.7V. In typical applications, an auxiliary transformer winding is connected through a diode to the VCC pin. This winding must raise the VCC voltage above 8V to shut off the internal start-up regulator. Powering VCC from an auxiliary winding improves efficiency while reducing the controller’s power dissipation. The VCC UV circuit will still function in this mode, requiring that VCC never falls below its UV threshold during the start-up sequence. The VCC regulator series pass transistor includes a diode between VCC and VIN that should not be forward biased in normal operation. Therefore, the auxiliary VCC voltage should never exceed the VIN voltage. An external DC bias voltage can be used instead of the internal regulator by connecting the external bias voltage to both the VCC and the VIN pins. This implementation is shown in the APPLICATIONS INFORMATION section. The external bias must be greater than 10V and less than the VCC maximum voltage rating of 14V. Line Under-Voltage Detector The LM5045 contains a dual level Under-Voltage Lockout (UVLO) circuit. When the UVLO pin voltage is below 0.4V, the controller is in a low current shutdown mode. When the UVLO pin voltage is greater than 0.4V but less than 1.25V, the controller is in standby mode. In standby mode the VCC and REF bias regulators are active while the controller outputs are disabled. When the VCC and REF outputs exceed their respective under-voltage thresholds and the UVLO pin voltage is greater than 1.25V, the soft-start capacitor is released and the normal operation begins. An external set-point voltage divider from VIN to GND can be used to set the minimum operating voltage of the converter. The divider must be designed such that the voltage at the UVLO pin will be greater than 1.25V when VIN enters the desired operating range. UVLO hysteresis is accomplished with an internal 20μA current sink that is switched on or off into the impedance of the set-point divider. When the UVLO threshold is exceeded, the current sink is deactivated to quickly raise the voltage at the UVLO pin. When the UVLO pin voltage falls below the 1.25V threshold, the current sink is enabled causing the voltage at the UVLO pin to quickly fall. The hysteresis of the 0.4V shutdown comparator is internally fixed at 50mV. The UVLO pin can also be used to implement various remote enable / disable functions. Turning off the converter by forcing the UVLO pin to standby condition (0.4V < UVLO < 1.25V) provides a controlled soft-stop. Refer to the Soft-Stop section for more details. 12 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Over Voltage Protection An external voltage divider can be used to set either an over voltage or an over temperature protection. During an OVP condition, the SS and SSSR capacitors are discharged and all the outputs are disabled. The divider must be designed such that the voltage at the OVP pin is greater than 1.25V when over voltage/temperature condition exists. Hysteresis is accomplished with an internal 20μA current source. When the OVP pin voltage exceeds 1.25V, the 20μA current source is activated to quickly raise the voltage at the OVP pin. When the OVP pin voltage falls below the 1.25V threshold, the current source is deactivated causing the voltage at the OVP to quickly fall. Refer to the APPLICATIONS INFORMATION section for more details. Reference The REF pin is the output of a 5V linear regulator that can be used to bias an opto-coupler transistor and external housekeeping circuits. The regulator output is internally current limited to 15mA. The REF pin needs to be locally decoupled with a ceramic capacitor, the recommended range of values are from 0.1μF to 10μF Oscillator, Sync Input The LM5045 oscillator frequency is set by a resistor connected between the RT pin and AGND. The RT resistor should be located very close to the device. To set a desired oscillator frequency (FOSC), the necessary value of RT resistor can be calculated from the following equation: RT = 1 FOSC x 1 x 10-10 (1) For example, if the desired oscillator frequency is 400 kHz i.e. each phase (LO1 or LO2) at 200 kHz, the value of RT will be 25kΩ. If the LM5045 is to be synchronized to an external clock, that signal must be coupled into the RT pin through a 100pF capacitor. The RT pin voltage is nominally regulated at 2.0V and the external pulse amplitude should lift the pin to between 3.5V and 5.0V on the low-to-high transition. The synchronization pulse width should be between 15 and 200ns. The RT resistor is always required, whether the oscillator is free running or externally synchronized and the SYNC frequency must be equal to, or greater than the frequency set by the RT resistor. When syncing to an external clock, it is recommended to add slope compensation by connecting an appropriate resistor from the VCC pin to the CS pin. Also disable the SLOPE pin by grounding it. Cycle-by-Cycle Current Limit The CS pin is to be driven by a signal representative of the transformer’s primary current. If the voltage on the CS pin exceeds 0.75V, the current sense comparator immediately terminates the PWM cycle. A small RC filter connected to the CS pin and located near the controller is recommended to suppress noise. An internal 18Ω MOSFET discharges the external current sense filter capacitor at the conclusion of every cycle. The discharge MOSFET remains on for an additional 40ns after the start of a new PWM cycle to blank leading edge spikes. The current sense comparator is very fast and may respond to short duration noise pulses. Layout is critical for the current sense filter and the sense resistor. The capacitor associated with CS filter must be placed very close to the device and connected directly to the CS and AGND pins. If a current sense transformer is used, both the leads of the transformer secondary should be routed to the filter network, which should be located close to the IC. When designing with a current sense resistor, all of the noise sensitive low power ground connections should be connected together near the AGND pin, and a single connection should be made to the power ground (sense resistor ground point). Hiccup Mode The LM5045 provides a current limit restart timer to disable the controller outputs and force a delayed restart (i.e. Hiccup mode) if a current limit condition is repeatedly sensed. The number of cycle-by-cycle current limit events required to trigger the restart is programmed by the external capacitor at the RES pin. During each PWM cycle, the LM5045 either sources or sinks current from the RES capacitor. If current limit is detected, the 5μA current sink is disabled and a 30μA current source is enabled. If the RES voltage reaches the 1.0V threshold, the following restart sequence occurs, as shown in Figure 12: • The SS and SSSR capacitors are fully discharged • The 30μA current source is turned-off and the 10μA current source is turned-on. • Once the voltage at the RES pin reaches 4.0V the 10μA current source is turned-off and a 5μA current sink is turned-on, ramping the voltage on the RES capacitor down to 2.0V. Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 13 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 • • • • www.ti.com Once RES capacitor reaches 2.0V, threshold, the 10μA current source is turned-on again. The RES capacitor voltage is ramped between 4.0V and 2.0V eight times. When the counter reaches eight, the RES pin voltage is pulled low and the soft-start capacitor is released to begin a soft-start sequence. The SS capacitor voltage slowly increases. When the SS voltage reaches 1.0V, the PWM comparator will produce the first narrow pulse. If the overload condition persists after restart, cycle-by-cycle current limiting will begin to increase the voltage on the RES capacitor again, repeating the hiccup mode sequence. If the overload condition no longer exists after restart, the RES pin will be held at ground by the 5μA current sink and the normal operation resumes. The hiccup mode function can be completely disabled by connecting the RES pin to the AGND pin. In this configuration the cycle-by-cycle protection will limit the maximum output current indefinitely, no hiccup restart sequences will occur. 4V 2V 1V Count to Eight Restart delay Soft-Start 1V Hiccup Mode off-time Figure 12. Hiccup Mode Delay and Soft-Start Timing Diagram PWM Comparator The LM5045 pulse width modulator (PWM) comparator is a three input device, it compares the signal at the RAMP pin to the loop error signal or the soft-start, whichever is lower, to control the duty cycle. This comparator is optimized for speed in order to achieve minimum controllable duty cycles. The loop error signal is received from the external feedback and isolation circuit in the form of a control current into the COMP pin. The COMP pin current is internally mirrored by a matching pair of NPN transistors which sink current through a 5kΩ resistor connected to the 5V reference. The resulting control voltage passes through a 1V offset, followed by a 2:1 resistor divider before being applied to the PWM comparator. An opto-coupler detector can be connected between the REF pin and the COMP pin. Because the COMP pin is controlled by a current input, the potential difference across the opto-coupler detector is nearly constant. The bandwidth limiting phase delay which is normally introduced by the significant capacitance of the opto-coupler is thereby greatly reduced. Higher loop bandwidths can be realized since the bandwidth limiting pole associated with the opto-coupler is now at a much higher frequency. The PWM comparator polarity is configured such that with no current flowing into the COMP pin, the controller produces maximum duty cycle. 14 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Ramp Pin The voltage at the RAMP pin provides the modulation ramp for the PWM comparator. The PWM comparator compares the modulation ramp signal at the RAMP pin to the loop error signal to control the duty cycle. The modulation ramp signal can be implemented either as a ramp proportional to the input voltage, known as feedforward voltage mode control, or as a ramp proportional to the primary current, known as current mode control. The RAMP pin is reset by an internal MOSFET with an RDS(ON) of 5.5Ω at the conclusion of each PWM cycle. The ability to configure the RAMP pin for either voltage mode or current mode allows the controller to be implemented for the optimum control method depending upon the design constraints. Refer to the APPLICATIONS INFORMATION section for more details on configuring the RAMP pin for feed-forward voltage mode control and peak current mode control. Slope Pin For duty cycles greater than 50% (25% for each phase), peak current mode control is subject to sub-harmonic oscillation. Sub-harmonic oscillation is normally characterized by observing alternating wide and narrow duty cycles. This can be eliminated by adding an artificial ramp, known as slope compensation, to the modulating signal at the RAMP pin. The SLOPE pin provides a current source ramping from 0 to 100μA, at the frequency set by the RT resistor, for slope compensation. The ramping current source at the SLOPE pin can be utilized in a couple of different ways to add slope compensation to the RAMP signal: 1. As shown in Figure 13(a), the SLOPE and RAMP pins can be connected together through an appropriate resistor to the CS pin. This configuration will inject current sense signal plus slope compensation to the RAMP pin but CS pin will not see any slope compensation. Therefore, in this scheme slope compensation will not affect the current limit. 2. In a second configuration, as shown in Figure 13(b), the SLOPE, RAMP and CS pins can be tied together. In this configuration the ramping current source from the SLOPE pin will flow through the filter resistor and filter capacitor, therefore both the CS pin and the RAMP pin will see the current sense signal plus the slope compensation ramp. In this scheme, the current limit is compensated by the slope compensation and the current limit onset point will vary. If the slope compensation is not required for e.g. in feed-forward voltage mode control, the SLOPE pin must be connected to the AGND pin. When the RT pin is synched to an external clock, it is recommended to disable the SLOPE pin and add slope compensation externally by connecting an appropriate resistor from the VCC pin to the CS pin. Please refer to the APPLICATIONS INFORMATION section for more details. LM5045 LM5045 100 PA SLOPE 100 PA 0 SLOPE RAMP RAMP CLK Current Sense RSLOPE RFILTER CLK Current Sense RFILTER CS CS CLK + LEB RCS 0 CLK + LEB RCS CFILTER (a) CFILTER (b) A. Slope Compensation Configured for PWM Only (No Current Limit Slope) B. Slope Compensation Configured for PWM and Current Limit Figure 13. Slope Compensation Configuration Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 15 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com Soft-Start The soft-start circuit allows the power converter to gradually reach a steady state operating point, thereby reducing the start-up stresses and current surges. When bias is supplied to the LM5045, the SS capacitor is discharged by an internal MOSFET. When the UVLO, VCC and REF pins reach their operating thresholds, the SS capacitor is released and is charged with a 20µA current source. Once the SS pin voltage crosses the 1V offset, SS controls the duty cycle. The PWM comparator is a three input device; it compares the RAMP signal against the lower of the signals between the soft-start and the loop error signal. In a typical isolated application, as the secondary bias is established, the error amplifier on the secondary side soft-starts and establishes closedloop control, steering the control away from the SS pin. One method to shutdown the regulator is to ground the SS pin. This forces the internal PWM control signal to ground, reducing the output duty cycle quickly to zero. Releasing the SS pin begins a soft-start cycle and normal operation resumes. A second shutdown method is presented in the UVLO section. Gate Driver Outputs The LM5045 provides four gate drivers: two floating high side gate drivers HO1 and HO2 and two ground referenced low side gate drivers LO1 and LO2. Each internal driver is capable of source 1.5A peak and sinking 2A peak. Initially, the diagonal HO1 and LO2 are turned-on together, followed by an off-time when all the four gate driver outputs are off. In the subsequent phase the diagonal HO2 and LO1 are turned on together followed by an off-time. The low-side gate drivers are powered directly by the VCC regulator. The HO1 and HO2 gate drivers are powered from a bootstrap capacitor connected between BST1/BST2 and HS1/HS2 respectively. An external diode connected between VCC (anode pin) and BST (cathode pin) provides the high side gate driver power by charging the bootstrap capacitor from VCC when the corresponding switch node (HS1/HS2 pin) is low. When the high side MOSFET is turned on, BST1 rises to a peak voltage equal to VCC + VHS1 where VHS1 is the switch node voltage. The BST and VCC capacitors should be placed close to the pins of the LM5045 to minimize voltage transients due to parasitic inductances since the peak current sourced to the MOSFET gates can exceed 1.5A. The recommended value of the BST capacitor is 0.1μF or greater. A low ESR / ESL capacitor, such as a surface mount ceramic, should be used to prevent voltage droop during the HO transitions. If the COMP pin is open circuit, the outputs will operate at maximum duty cycle. The maximum duty cycle for each phase is limited by the dead-time set by the RD1 resistor. If the RD1 resistor is set to zero then the maximum duty cycle is slightly less than 50% due to the internally fixed dead-time. The internally fixed dead-time is 30ns which does not vary with the operating frequency. The maximum duty cycle for each output can be calculated from the following equation: ( F 1 ) - (T1) DMAX = OSC (F 2 ) OSC where • • T1 is the time set by the RD1 resistor FOSC is the frequency of the oscillator (2) For example, if the oscillator frequency is set at 400 kHz and the T1 time set by the RD1 resistor is 60ns, the resulting DMAX will be equal to 0.488. 16 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 CLK HO1,LO2 Tonmax Tosc HO2,LO1 T1 T1 TOSC = 1 FOSC T1 D RD1 Figure 14. Timing Diagram Illustrating the Maximum Duty Cycle and Dead-Time Set by RD1 Synchronous Rectifier Control Outputs (SR1 & SR2) Synchronous rectification (SR) of the transformer secondary provides higher efficiency, especially for low output voltage converters, compared to the diode rectification. The reduction of rectifier forward voltage drop (0.5V 1.5V) to 10mV - 200mV VDS voltage for a MOSFET significantly reduces rectification losses. In a typical application, the transformer secondary winding is center tapped, with the output power inductor in series with the center tap. The SR MOSFETs provide the ground path for the energized secondary winding and the inductor current. From Figure 15 it can be seen that when the HO1/LO2 diagonal is turned ON, power transfer is enabled from the primary. During this period, the SR1 MOSFET is enabled and the SR2 MOSFET is turned-off. The secondary winding connected to the SR2 MOSFET drain is twice the voltage of the center tap at this time. At the conclusion of the HO1/LO2 pulse, the inductor current continues to flow through the SR2 MOSFET body diode. Since the body diode causes more loss than the SR MOSFET, efficiency can be improved by minimizing the T2 period while maintaining sufficient timing margin over all conditions (component tolerances, etc.) to prevent the shoot-through current. When HO2/LO1 enables power transfer from the primary, the SR2 MOSFET is enabled and the SR1 MOSFET is off. During the freewheeling period, the inductor current is almost equally shared between both the SR1 and SR2 MOSFETs which effectively shorts the transformer secondary. The SR2 MOSFET is disabled before HO1/LO2 is turned-on. The SR2 MOSFET body diode continues to carry about the half inductor current until the primary power raises the SR2 MOSFET drain voltage and reverse biases the body diode. Ideally, dead-time T1 would be set to the minimum time that allows the SR MOSFET to turn off before the SR MOSFET body diode starts conducting. The SR drivers are powered by the REF regulator and each SR output is capable of sourcing 0.1A and sinking 0.4A peak. The amplitude of the SR drivers is limited to 5V. The 5V SR signals enable the LM5045 to transfer SR control across the isolation barrier either through a solid-state isolator or a pulse transformer. The actual gate sourcing and sinking currents for the synchronous MOSFETs are provided by the secondary-side bias and gate drivers. T1 and T2 can be programmed by connecting a resistor between RD1 and RD2 pins and AGND. It should be noted that while RD1 effects the maximum duty cycle, RD2 does not. The RD1 and RD2 resistors should be located very close to the device. The formula for RD1 and RD2 resistors are given below: RD(1,2) = T(1,2) ; For 20k < (1,2) < 100k 3 pF (3) If the desired dead-time for T1 is 60ns, then the RD1 will be 20 kΩ. Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 17 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com HO1, LO2 SR2 T1 T2 HO2, LO1 SR1 T1 T2 Figure 15. Synchronous Rectifier Timing Diagram Soft-Start of the Synchronous Rectifiers In addition to the basic soft-start already described, the LM5045 contains a second soft-start function that gradually turns on the synchronous rectifiers to their steady-state duty cycle. This function keeps the synchronous rectifiers off during the basic soft-start allowing a linear start-up of the output voltage even into prebiased loads. Then the SR output duty cycle is gradually increased to prevent output voltage disturbances due to the difference in the voltage drop between the body diode and the channel resistance of the synchronous MOSFETs. Initially, when bias is supplied to the LM5045, the SSSR capacitor is discharged by an internal MOSFET. When the SS capacitor reaches a 2V threshold and once it is established that COMP is in control of the duty cycle i.e. ICOMP < 800µA, the SSSR discharge is released and SSSR capacitor begins charging with a 20µA current source. Once the SSSR cap crosses the internal 1V threshold, the LM5045 begins the soft-start of the synchronous FETs. The SR soft-start follows a leading edge modulation technique i.e. the leading edge of the SR pulse is soft-started as opposed trailing edge modulation of the primary FETs. As shown in the Figure 16(a), SR1 and SR2 are turned-on simultaneously with a narrow pulse-width during the freewheeling cycle. At the end of the freewheel cycle i.e. at the rising edge of the internal CLK, the SR FET in-phase with the next power transfer cycle is kept on while the SR FET out of phase with it is turned-off. The in-phase SR FET is kept on throughout the power transfer cycle and at the end of it, both the primary FETs and the in-phase SR FETs are turned-off together. The synchronous rectifier outputs can be disabled by grounding the SSSR pin. 18 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 CLK HO2/LO1 HO1/LO2 SR1 T1 T2 SR2 Power Transfer T1 Freewheel Waveforms during soft-start A. Waveforms during Soft-Start B. Waveforms after Soft-Start T2 Waveforms after soft-start Figure 16. Pre-Bias Startup A common requirement for power converters is to have a monotonic output voltage start-up into a pre-biased load i.e. a pre-charged output capacitor. In a pre-biased load condition, if the synchronous rectifiers are engaged prematurely they will sink current from the pre-charged output capacitors resulting in an undesired output voltage dip. This condition is undesirable and could potentially damage the power converter. The LM5045 utilizes unique control circuitry to ensure intelligent turn-on of the synchronous rectifiers such that the output has a monotonic startup. Initially, the SSSR capacitor is held at ground to disable the synchronous MOSFETs allowing the body diode to conduct. The synchronous rectifier soft-start is initiated once it is established the duty cycle is controlled by the COMP instead of the soft-start capacitor i.e. ICOMP < 800µA and the voltage at the SS pin>2V. The SSSR capacitor is then released and is charged by a 20µA current source. Further, as shown in Figure 17, a 1V offset on the SSSR pin is used to provide additional delay. This delay ensures the output voltage is in regulation avoiding any reverse current when the synchronous MOSFETs are engaged. Soft-Stop As shown in Figure 18, if the UVLO pin voltage falls below the 1.25V standby threshold, but above the 0.4V shutdown threshold, the SSSR capacitor is soft-stopped with a 60µA current source (3 times the charging current). Once the SSSR pin reaches the 1.0V threshold, both the SS and SSSR pins are immediately discharged to GND. Soft-stopping the power converter gradually winds down the energy in the output capacitors and results in a monotonic decay of the output voltage. During the hiccup mode, the same sequence is executed except that the SSSR is discharged with a 120µA current source (6 times the charging current). In case of an OVP, VCC UV, thermal limit or a VREF UV condition, the power converter hard-stops, whereby all of the control outputs are driven to a low state immediately. Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 19 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com 2.0V SS 1.0V Primary Secondary Bias COMP 1.0V SSSR SR1, SR2 VOUT Prebiased Load Figure 17. Pre-Bias Voltage Startup Waveforms Soft-Stop Off The Soft-Start Off (SSOFF) pin gives additional flexibility by allowing the power converter to be configured for hard-stop during line UVLO and hiccup mode condition. If the SS OFF pin is pulled up to the 5V REF pin, the power converter hard-stops in any fault condition. Hard-stop drives each control output to a low state immediately. Refer to Table 1 for more details. 1.25V VIN UVLO 1.25V 0.45V SS SSSR 1.0V Figure 18. Stop-Stop Waveforms during a UVLO Event 20 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Table 1. Soft-Stop in Fault Conditions (1) (1) Fault Condition SSSR UVLO (UVLO<1.25V) Soft-Stop 3x the charging rate OVP (OVP>1.25V) Hard-Stop Hiccup (CS>0.75 and RES>1V) Soft-Stop 6x the charging rate VCC/VREF UV Hard-Stop Internal Thermal Limit Hard-Stop Note: All the above conditions are valid with SSOFF pin tied to GND. If SSOFF=5V, the LM5045 hard-stops in all the conditions. The SS pin remains high in all the conditions until the SSSR pin reaches 1V. Thermal Protection Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event the maximum rated junction temperature is exceeded. When activated, typically at 160°C, the controller is forced into a shutdown state with the output drivers, the bias regulators (VCC and REF) disabled. This helps to prevent catastrophic failures from accidental device overheating. During thermal shutdown, the SS and SSSR capacitors are fully discharged and the controller follows a normal start-up sequence after the junction temperature falls to the operating level (140 °C). APPLICATIONS INFORMATION Control Method Selection The LM5045 is a versatile PWM control IC that can be configured for either current mode control or voltage mode control. The choice of the control method usually depends upon the designer preference. The following must be taken into consideration while selecting the control method. Current mode control can inherently balance flux in both phases of the full-bridge topology. The full-bridge topology, like other double ended topologies, is susceptible to the transformer core saturation. Any asymmetry in the volt-second product applied between the two alternating phases results in flux imbalance that causes a dc buildup in the transformer. This continual dc buildup may eventually push the transformer into saturation. The volt-second asymmetry can be corrected by employing current mode control. In current mode control, a signal representative of the primary current is compared against an error signal to control the duty cycle. In steady-state, this results in each phase being terminated at the same peak current by adjusting the pulse-width and thus applying equal volt-seconds to both the phases. Current mode control can be susceptible to noise and sub-harmonic oscillation, while voltage mode control employs a larger ramp for PWM and is usually less susceptible. Voltage-mode control with input line feedforward also has excellent line transient response. When configuring for voltage mode control, a dc blocking capacitor can be placed in series with the primary winding of the power transformer to avoid any flux imbalance that may cause transformer core saturation. Voltage Mode Control Using the LM5045 To configure the LM5045 for voltage mode control, an external resistor (RFF) and capacitor (CFF) connected to VIN, AGND, and the RAMP pins is required to create a saw-tooth modulation ramp signal shown in Figure 19. The slope of the signal at RAMP will vary in proportion to the input line voltage. The varying slope provides line feed-forward information necessary to improve line transient response with voltage mode control. With a constant error signal, the on-time (TON) varies inversely with the input voltage (VIN) to stabilize the Volt- Second product of the transformer primary. Using a line feed-forward ramp for PWM control requires very little change in the voltage regulation loop to compensate for changes in input voltage, as compared to a fixed slope oscillator ramp. Furthermore, voltage mode control is less susceptible to noise and does not require leading edge filtering. Therefore, it is a good choice for wide input range power converters. Voltage mode control requires a Type-III compensation network, due to the complex-conjugate poles of the L-C output filter. Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 21 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 SLOPE PROPORTIONAL TO VIN www.ti.com VIN 5V COMP RFF VIN 5k R R 1V Gate Drive 1:1 RAMP CLK CFF LM5045 Figure 19. Feed-Forward Voltage Mode Configuration The recommended capacitor value range for CFF is from 100pF to 1800pF. Referring to Figure 19, it can be seen that CFF value must be small enough to be discharged with in the clock pulse-width which is typically within 50ns. The RDS(ON) of the internal discharge FET is 5.5Ω. The value of RFF required can be calculated from RFF = -1 FOSC x CFF x In (1- VRAMP ) VINMIN (4) For example, assuming a VRAMP of 1.5V (a good compromise of signal range and noise immunity), at VINMIN of 36V (oscillator frequency of 400 kHz and CFF = 470pF results in a value for RFF of 125 kΩ. Current Mode Control Using the LM5045 The LM5045 can be configured for current mode control by applying a signal proportional to the primary current to the RAMP pin. One way to achieve this is shown in Figure 20. The primary current can be sensed using a current transformer or sense resistor, the resulting signal is filtered and applied to the RAMP pin through a resistor used for slope compensation. It can be seen that the signal applied to the RAMP pin consists of the primary current information from the CS pin plus an additional ramp for slope compensation, added by the resistor RSLOPE. The current sense resistor is selected such that during over current condition, the voltage across the current sense resistor is above the minimum CS threshold of 728mV. In general, the amount of slope compensation required to avoid sub-harmonic oscillation is equal to at least onehalf the down-slope of the output inductor current, transformed to the primary. To mitigate sub-harmonic oscillation after one switching period, the slope compensation has to be equal to one times the down slope of the filter inductor current transposed to primary. This is known as deadbeat control. The slope compensation resistor required to implement dead-beat control can be calculated as follows: where • NTR is the turns-ratio with respect to the secondary (5) For example, for a 3.3V output converter with a turns-ratio between primary and secondary of 9:1, an output filter inductance (LFILTER) of 800nH and a current sense resistor (RSENSE) of 150mΩ, RSLOPE of 1.67kΩ will suffice. 22 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 VIN and VCC The voltage applied to the VIN pin, which may be the same as the system voltage applied to the power transformer’s primary (VPWR), can vary in the range of the 14 to 100V. It is recommended that the filter shown in Figure 21 be used to suppress the transients that may occur at the input supply. This is particularly important when VIN is operated close to the maximum operating rating of the LM5045. The current into VIN depends primarily on the LM5045’s operating current, the switching frequency, and any external loads on the VCC pin, that typically include the gate capacitances of the power MOSFETs. In typical applications, an auxiliary transformer winding is connected through a diode to the VCC pin. This pin must raise VCC voltage above 8V to shut off the internal start-up regulator. After the outputs are enabled and the external VCC supply voltage has begun supplying power to the IC, the current into the VIN pin drops below 1mA. VIN should remain at a voltage equal to or above the VCC voltage to avoid reverse current through the internal body diode of the internal VCC regulator. For Applications with > 100V Input For applications where the system input voltage exceeds 100V, VIN can be powered from an external start-up regulator as shown in Figure 22. In this configuration, the VIN and VCC pins should be connected together. The voltage at the VCC and VIN pins must be greater than 10V (>Max VCC reference voltage) yet not exceed 16V. To enable operation the VCC voltage must be raised above 10V. The voltage at the VCC pin must not exceed 16V. The voltage source at the right side of Figure 22 is typically derived from the power stage, and becomes active once the LM5045’s outputs are active. LM5045 100 PA SLOPE 0 RAMP CLK Current Sense RSLOPE RFILTER CS CLK + LEB RCS CFILTER Figure 20. Current Mode Configuration VPWR 50 VIN 0.1 PF LM5045 Figure 21. Input Transient Protection Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 23 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com 10V - 16V (from aux winding) VPWR VIN VCC LM5045 11V Figure 22. Start-up Regulator for VPWR>100V UVLO and OVP Voltage Divider Selection Two dedicated comparators connected to the UVLO and OVP pins are used to detect under voltage and over voltage conditions. The threshold values of both these comparators are set at 1.25V. The two functions can be programmed independently with two separate voltage dividers from VIN to AGND as shown in Figure 23 and Figure 24, or with a three-resistor divider as shown in Figure 25. Independent UVLO and OVP pins provide greater flexibility for the user to select the operational voltage range of the system. When the UVLO pin voltage is below 0.4V, the controller is in a low current shutdown mode. For a UVLO pin voltage greater than 0.4V but less than 1.25V the controller is in standby mode. Once the UVLO pin voltage is greater than 1.25V, the controller is fully enabled. Two external resistors can be used to program the minimum operational voltage for the power converter as shown in Figure 23. When the UVLO pin voltage falls below the 1.25V threshold, an internal 20µA current sink is enabled to lower the voltage at the UVLO pin, thus providing threshold hysteresis. Resistance values for R1 and R2 can be determined from the following equations: R1 = R2 = VHYS 20 PA 1.25V x R1 VPWR-OFF -1.25V - (20 PA x R1) where • • VPWR is the desired turn-on voltage VHYS is the desired UVLO hysteresis at VPWR (6) For example, if the LM5045 is to be enabled when VPWR reaches 33V, and disabled when VPWR is decreased to 31V, R1 should be 100kΩ, and R2 should be 4.2kΩ. The voltage at the UVLO pin should not exceed 7V at any time. Two external resistors can be used to program the maximum operational voltage for the power converter as shown in Figure 24. When the OVP pin voltage rises above the 1.25V threshold, an internal 20µA current source is enabled to raise the voltage at the OVP pin, thus providing threshold hysteresis. Resistance values for R1 and R2 can be determined from the following equations: R1 = R2 = VHYS 20 PA 1.25V x R1 VPWR -1.25V + (20 PA x R1) (7) If the LM5045 is to be disabled when VPWR-OFF reaches 80V and enabled when it is decreased to 78V. R1 should be 100kΩ, and R2 should be 1.5 kΩ. The voltage at the OVP pin should not exceed 7V at any time. 24 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 VPWR LM5045 R1 1.25V STANDBY UVLO 20 PA R2 0.4V SHUTDOWN Figure 23. Basic UVLO Configuration LM5045 5V VPWR 20 PA R1 OVP STANDBY 1.25V R2 Figure 24. Basic OVP Configuration VPWR R1 UVLO 1.25V STANDBY LM5045 20 PA 0.4V R2 SHUTDOWN 5V 20 PA OVP 1.25V STANDBY R3 Figure 25. UVLO/OVP Divider The UVLO and OVP can also be set together using a 3 resistor divider ladder as shown in Figure 25. R1 is calculated as explained in the basic UVLO divider selection. Using the same values, as in the above two examples, for the UVLO and OVP set points, R1 and R3 remain the same at 100kΩ and 1.5kΩ. The R2 is 2.7kΩ obtained by subtracting R3 from 4.2kΩ. Remote configuration of the controller’s operational modes can be accomplished with open drain device(s) connected to the UVLO pin as shown in Figure 26. Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 25 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com Figure 27 shows an application of the OVP comparator for Remote Thermal Protection using a thermistor (or multiple thermistors) which may be located near the main heat sources of the power converter. The negative temperature coefficient (NTC) thermistor is nearly logarithmic, and in this example a 100kΩ thermistor with the β material constant of 4500 Kelvin changes to approximately 2kΩ at 130ºC. Setting R1 to one-third of this resistance (665Ω) establishes 130ºC as the desired trip point (for VREF = 5V). In a temperature band from 20ºC below to 20ºC above the OVP threshold, the voltage divider is nearly linear with 25mV per ºC sensitivity. R2 provides temperature hysteresis by raising the OVP comparator input by R2 x 20µA. For example, if a 22kΩ resistor is selected for R2, then the OVP pin voltage will increase by 22k x 20µA = 506mV. The NTC temperature must therefore fall by 506mV / 25mV per ºC = 20ºC before the LM5045 switches from standby mode to the normal mode. VPWR LM5045 R1 1.25V STANDBY UVLO STANDBY R2 SHUTDOWN 20 PA 0.4V SHUTDOWN Figure 26. Remote Standby and Disable Control NTC THERMISTOR LM5045 5V VPWR 20 PA T R1 OVP STANDBY R2 1.25V Figure 27. Remote Thermal Protection Current Sense The CS pin receives an input signal representative of its transformer’s primary current, either from a current sense transformer or from a resistor located at the junction of source pin of the primary switches, as shown in Figure 28 and Figure 29 respectively. In both the cases, the filter components RF and CF should be located as close to the IC as possible, and the ground connection from the current sense transformer, or RSENSE should be a dedicated trace to the appropriate GND pin. Please refer to the Printed Circuit Board Layout section for more layout tips. The current sense components must provide a signal > 710mV at the CS pin during an over-load event. Once the voltage on the CS pin crosses the current limit threshold, the current sense comparator terminates the PWM pulse and starts to charge the RES pin. Depending on the configuration of the RES pin, the LM5045 will eventually initiate a hiccup mode restart or be in continuous current limit. 26 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 VPWR Q3 Q1 VIN NS1 RF CS NP LM5045 RCS CF NS2 AGND Q2 Q4 Figure 28. Transformer Current Sense Q3 Q1 NP Q4 Q2 VIN CS LM5045 RF CF RCS AGND Figure 29. Resistor Current Sense Hiccup Mode Current Limit Restart The operation of the hiccup mode restart circuit is explained in the FUNCTIONAL DESCRIPTION section. During a continuous current limit condition, the RES pin is charged with 30µA current source. The restart delay time required to reach the 1.0V threshold is given by: TCS = CRES x 1.0V 30 PA (8) This establishes the time allowed before the IC initiates a hiccup restart sequence. For example, if the CRES=0.01µF, the time TCS as noted in Figure 30 below is 334µs. Once the RES pin reaches 1.0V, the 30µA current source is turned-off and a 10µA current source is turned-on during the ramp up to 4V and a 5µA is turned on during the ramp down to 2V. The hiccup mode off-time is given by: THICCUP = CRES x (2.0Vx8) CRES x ((2.0Vx8) + 1.0V) + 10 µA 5 µA (9) With a CRES=0.01µF, the hiccup time is 49ms. Once the hiccup time is finished, the RES pin is pulled-low and the SS pin is released allowing a soft-start sequence to commence. Once the SS pin reaches 1V, the PWM pulses will commence. The hiccup mode provides a cool-down period for the power converter in the event of a sustained overload condition thereby lowering the average input current and temperature of the power components during such an event. Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 27 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com 4V 2V 1V Count to Eight Restart delay Soft-Start 1V Hiccup Mode off-time Figure 30. Hiccup Mode Delay and Soft-Start Timing Diagram Augmenting the Gate Drive Strength The LM5045 includes powerful 2A integrated gate drivers. However, in certain high power applications (>500W), it might be necessary to augment the strength of the internal gate driver to achieve higher efficiency and better thermal performance. In high power applications, typically, the I2xR loss in the primary MOSFETs is significantly higher than the switching loss. In order to minimize the I2xR loss, either the primary MOSFETs are paralleled or MOSFETs with low RDS (on) are employed. Both these scenarios increase the total gate charge to be driven by the controller IC. An increase in the gate charge increases the FET transition time and hence increases the switching losses. Therefore, to keep the total losses within a manageable limit the transition time needs to be reduced. Generally, during the miller capacitance charge/discharge the total available driver current is lower during the turn-off process than during the turn-on process and often it is enough to speed-up the turn-off time to achieve the efficiency and thermal goals. This can be achieved simply by employing a PNP device, as shown in Figure 31, from gate to source of the power FET. During the turn-on process, when the LO1 goes high, the current is sourced through the diode D1 and the BJT Q1 provides the path for the turn-off current. Q1 should be located as close to the power FET as possible so that the turn-off current has the shortest possible path to the ground and does not have to pass through the controller. VIN LM5045 BST1 D1 HO1 Q1 HS1 VCC LO1 PGND Figure 31. Circuit to Speed-up the Turn-off Process 28 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 Depending on the gate charge characteristics of the primary FET, if it is required to speed up both the turn-on and the turn-off time, a bipolar totem pole structure as shown in Figure 32 can be used. When LO1 goes high, the gate to source current is sourced through the NPN transistor Q1 and similar to the circuit shown in Figure 31 when LO1 goes low, the PNP transistor Q2 expedites the turn-off process. VIN LM5045 BST1 Q1 HO1 Q2 HS1 VCC LO1 PGND Figure 32. Bipolar Totem Pole Arrangement Alternatively, a low side gate driver such as LM5112 can be utilized instead of the discrete totem pole. The LM5112 comes in a small package with a 3A source and a 7A sink capability. While driving the high-side FET, the HS1 acts as a local ground and the boot capacitor between the BST and HS pins acts as VCC. VIN LM5045 BST1 HO1 LM5112 HS1 VCC LO1 LM5112 PGND Figure 33. Using a Low Side Gate Driver to Augment Gate Drive Strength Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 29 LM5045 SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 www.ti.com Printed Circuit Board Layout The LM5045 current sense and PWM comparators are very fast and respond to short duration noise pulses. The components at the CS, COMP, SLOPE, RAMP, SS, SSSR, RES, UVLO, OVP, RD1, RD2, and RT pins should be physically close as possible to the IC, thereby minimizing noise pickup on the PC board trace inductance. Eliminating or minimizing via’s in these critical connections are essential. Layout consideration is critical for the current sense filter. If a current sense transformer is used, both leads of the transformer secondary should be routed to the sense filter components and to the IC pins. The ground side of the transformer should be connected via a dedicated PC board trace to the AGND pin, rather than through the ground plane. If the current sense circuit employs a sense resistor in the drive transistor source, low inductance resistors should be used. In this case, all the noise sensitive, low-current ground trace should be connected in common near the IC, and then a single connection made to the power ground (sense resistor ground point). The gate drive outputs of the LM5045 should have short, direct paths to the power MOSFETs in order to minimize inductance in the PC board. The boot-strap capacitors required for the high side gate drivers should be located very close to the IC and connected directly to the BST and HS pins. The VCC and REF capacitors should also be placed close to their respective pins with short trace inductance. Low ESR and ESL ceramic capacitors are recommended for the boot-strap, VCC and the REF capacitors. The two ground pins (AGND, PGND) must be connected together directly underneath the IC with a short, direct connection, to avoid jitter due to relative ground bounce. Application Circuit Example The following schematic shows an example of a 100W full-bridge converter controlled by LM5045. The operating input voltage range is 36V to 75V, and the output voltage is 3.3V. The output current capability is 30 Amps. The converter is configured for current mode control with external slope compensation. An auxiliary winding is used to raise the VCC voltage to reduce the controller power dissipation. Evaluation Board Schematic 30 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 LM5045 www.ti.com SNVS699G – FEBRUARY 2011 – REVISED MARCH 2013 REVISION HISTORY Changes from Revision F (March 2013) to Revision G • Page Changed layout of National Data Sheet to TI format .......................................................................................................... 30 Submit Documentation Feedback Copyright © 2011–2013, Texas Instruments Incorporated Product Folder Links: LM5045 31 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) LM5045MH/NOPB ACTIVE HTSSOP PWP 28 48 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM5045 MH LM5045MHX/NOPB ACTIVE HTSSOP PWP 28 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LM5045 MH LM5045SQ/NOPB ACTIVE WQFN RSG 28 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L5045 LM5045SQX/NOPB ACTIVE WQFN RSG 28 4500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L5045 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LM5045MHX/NOPB HTSSOP PWP 28 2500 330.0 16.4 LM5045SQ/NOPB WQFN RSG 28 1000 178.0 LM5045SQX/NOPB WQFN RSG 28 4500 330.0 6.8 10.2 1.6 8.0 16.0 Q1 12.4 5.3 5.3 1.3 8.0 12.0 Q1 12.4 5.3 5.3 1.3 8.0 12.0 Q1 Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM5045MHX/NOPB HTSSOP PWP 28 2500 367.0 367.0 35.0 LM5045SQ/NOPB WQFN RSG 28 1000 210.0 185.0 35.0 LM5045SQX/NOPB WQFN RSG 28 4500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA PWP0028A MXA28A (Rev D) www.ti.com MECHANICAL DATA RSG0028A SQA28A (Rev B) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated