TE MS5535C Piezoresistive silicon micromachined sensor Datasheet

MS5535C
14 bar Pressure Sensor Module
SPECIFICATIONS








0 – 14 bar absolute pressure range
6 coefficients for software compensation stored
on-chip
Piezoresistive silicon micromachined sensor
Integrated miniature pressure sensor 9 x 9 mm
16 Bit ADC
3-wire serial interface
1 system clock line (32.768 kHz)
Low voltage and low power consumption
The MS5535C is a SMD-hybrid device including a
piezoresistive pressure sensor and an ADC-Interface IC. It
provides a 16 Bit data word from a pressure and temperature
dependent voltage. Additionally the module contains 6 readable
coefficients for a highly accurate software calibration of the sensor.
MS5535C is a low power, low voltage device with automatic power
down (ON/OFF) switching. A 3-wire interface is used for all
communications with a microcontroller.
The MS5535C is fully software compatible to the previous versions
(MS5535A and MS5535B). Compared to the previous versions the
ESD sensitivity has been improved to 4kV on all pins.
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 1
MS5535C
14 bar Pressure Sensor Module
FEATURES





Supply voltage 2.2 V to 3.6 V
Low supply current
-40°C to +125°C operation temperature
No external components required
16 Bit ADC resolution pressure measurement
and control systems
APPLICATIONS


Mobile water depth measurement systems
Diving computers and divers watches
BLOCK DIAGRAM
VDD
MCLK
Input MUX
SENSOR
Digital
Interface
+IN
-IN
ADC
Sensor
Interface IC
DIN
DOUT
dig.
Filter
SCLK
Memory
(PROM)
64 bits
SGND
GND
Fig. 1: Block diagram MS5535C
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 2
MS5535C
14 bar Pressure Sensor Module
PIN CONFIGURATION
Fig. 2: Pin configuration of MS5535C
Pin Name
GND
SCLK
DOUT
DIN
MCLK
VDD
PEN (1)
PV (1)
Pin
1
2
3
4
5
6
7
8
Type
G
I
O
I
I
P
I
N
Function
Ground
Serial data clock
Data output
Data input
Master clock (32.768 kHz)
Positive supply voltage
Programming enable
Negative programming voltage
NOTE
1) Pin 7 (PV) and Pin 8 (PEN) are only used by the manufacturer for calibration purposes and should not be
connected.
ABSOLUTE MAXIMUM RATINGS
Parameter
Supply voltage
Storage temperature
Overpressure
Symbol
VDD
TS
P
Conditions
Ta = 25 °C
Min
-0.3
-40
Ta = 25 °C
Max
4
+125
30
Unit
V
°C
bar
Notes
1
2
NOTES
1) Storage and operation in an environment of dry and non-corrosive gases.
2) The MS5535-CM is qualified referring to the ISO 6425 standard and can withstand an absolute pressure of 30
bar in salt water.
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 3
MS5535C
14 bar Pressure Sensor Module
RECOMMENDED OPERATING CONDITIONS
Parameter
Operating pressure range
Supply voltage
Supply current,
average (1)
during conversion (2)
standby (no conversion)
Current consumption into MCLK
(3)
Operating temperature range
Conversion time
External clock signal (4)
Duty cycle of MCLK
Serial data clock
Symbol
p
VDD
(Ta = 25 °C, VDD = 3.0 V unless noted otherwise)
Min
Typ
Max
Unit
0
14
bar
2.2
3.0
3.6
V
Conditions
VDD = 3.0 V
Iavg
Isc
Iss
4
1
MCLK = 32.768 kHz
T
tconv
MCLK
-40
MCLK = 32.768 kHz
30.000
40/60
SCLK
32.768
50/50
0.1
µA
mA
µA
0.5
µA
+125
35
35.000
60/40
500
°C
ms
kHz
%
kHz
NOTES
1) Under the assumption of one conversion every second. Conversion means either a pressure or a temperature
measurement started by a command to the serial interface of MS5535C.
2) During conversion the sensor will be switched on and off in order to reduce power consumption; the total on
time within a conversion is about 2 ms.
3) This value can be reduced by switching off MCLK while MS5535C is in standby mode.
4) It is strongly recommended that a crystal oscillator be used because the device is sensitive to clock jitter. A
square-wave form of the clock signal is a must.
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 4
MS5535C
14 bar Pressure Sensor Module
ELECTRICAL CHARACTERISTICS
DIGITAL INPUTS
Parameter
Input High Voltage
Input Low Voltage
Signal Rise Time
Signal Fall Time
Symbol
VIH
VIL
tr
tf
Conditions
Symbol
VOH
VOL
tr
tf
Conditions
Isource = 0.6 mA
Isink = 0.6 mA
Symbol
Conditions
(T = -40 °C .. 125 °C, VDD = 2.2 V .. 3.6 V)
Min
Typ
Max
Unit
80% VDD
100% VDD
V
0% VDD
20% VDD
V
200
ns
200
ns
DIGITAL OUTPUTS
Parameter
Output High Voltage
Output Low Voltage
Signal Rise Time
Signal Fall Time
(T = -40 °C .. 125 °C, VDD = 2.2 V .. 3.6 V)
Min
Typ
Max
Unit
80% VDD
100% VDD
V
0% VDD
20% VDD
V
200
ns
200
ns
AD-CONVERTER
Parameter
Resolution
Linear Range
Conversion Time
INL
SENSOR SOLUTIONS ///MS5535C
(T = -40 °C .. 125 °C, VDD = 2.2 V .. 3.6 V)
Typ
Max
Unit
16
Bit
4'000
40'000
LSB
35
ms
-5
+5
LSB
Min
MCLK = 32.768 kHz
Within linear range
09/2015
Page 5
MS5535C
14 bar Pressure Sensor Module
PRESSURE OUTPUT CHARACTERISTICS
With the calibration data stored in the interface IC of the MS5535C, the following characteristics can be achieved:
Parameter
Resolution
Absolute Pressure Accuracy
(Temperature range 0 .. +40 °C)
Absolute Pressure Accuracy
(Temperature range -40 .. +85 °C)
Absolute Pressure Accuracy
(Temperature range -40 ..+125°C)
Long-term Stability
Maximum Error over Supply
Voltage
Conditions
Min
p = 0 .. 5 bar
p = 0 .. 10 bar
p = 0 .. 14 bar
p = 0 .. 5 bar
p = 0 .. 10 bar
p = 0 .. 14 bar
p = 0 .. 5 bar
p = 0 .. 10 bar
p = 0 .. 14 bar
6 months
VDD = 2.2 .. 3.6 V
p = const.
-20
-40
-100
-40
-60
-160
-80
-100
-300
-1.6
(VDD = 3.0 V unless noted otherwise)
Typ
Max
Unit
Notes
1.2
mbar
1
+20
+20
mbar
2
+20
+100
mbar
2
+180
+200
+200
mbar
2
+200
+200
20
mbar
3
1.6
mbar
NOTES
1) A stable pressure reading of the given resolution requires taking the average of 2 to 4 subsequent pressure
values due to noise of the ADC.
2) Maximum error of pressure reading over the pressure range.
3) The long-term stability is measured with non-soldered devices.
TEMPERATURE OUTPUT CHARACTERISTICS
This temperature information is not required for most applications, but it is necessary to allow for temperature
compensation of the output.
Parameter
Resolution
Conditions
Accuracy
T = 20 °C
T = -40 .. +125°C
Min
0.005
-0.8
-4
Maximum Error over Supply
Voltage
VDD = 2.2 .. 3.6 V
-0.2
(VDD = 3.0 V unless noted otherwise)
Typ
Max
Unit
Notes
0.01
0.015
°C
0.8
°C
+6
°C
1
+0.2
°C
NOTE
1) With the second-order temperature compensation as described in Section "FUNCTION". See next section for
typical operating curves.
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 6
MS5535C
14 bar Pressure Sensor Module
TYPICAL PERFORMANCE CURVES
ADC-value D1 vs Pressure (typical)
30000
ADC-value D1 (LSB)
25000
-40°C
25°C
125°C
20000
15000
10000
0
2000
4000
6000
8000
10000
12000
14000
Pressure (mbar)
ADC-value D2 vs Temperature (typical)
45000
40000
ADC-value D2 (LSB)
35000
30000
25000
20000
15000
-40
-20
0
20
40
60
80
100
120
Temperature (°C)
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 7
MS5535C
14 bar Pressure Sensor Module
Absolute Pressure Accuracy after Calibration, 1st order compensation
250
200
Pressure error (mbar)
150
125°C
100
85°C
60°C
25°C
0°C
50
-40°C
0
0
2000
4000
6000
8000
10000
12000
14000
-50
-100
Pressure (mbar)
Absolute Pressure Accuracy after Calibration, 2nd order compensation
100
50
0
Pressure error (mbar)
0
2000
4000
6000
8000
10000
12000
14000
125°C
-50
85°C
60°C
25°C
0°C
-100
-40°C
-150
-200
-250
Pressure (mbar)
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 8
MS5535C
14 bar Pressure Sensor Module
Pressure Error Accuracy vs temperature (typical)
100
75
Pressure error (mbar)
50
Pres. error 4bar (1st order)
25
Pres. error 4bar (2nd order)
0
-40
-20
0
20
40
60
80
100
120
-25
-50
Temperature (°C)
Temperature Error Accuracy vs temperature (typical)
15
Temperature error (°C)
10
Temperature error (standard
calculation)
Temperature error (with 2nd
order calculation)
5
0
-40
-20
0
20
40
60
80
100
120
-5
Temperature (°C)
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 9
MS5535C
14 bar Pressure Sensor Module
Pressure error vs supply voltage (typical)
10
8
6
Pressure error (mbar)
4
14000 mbar
2
6000 mbar
0
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
1000 mbar
-2
-4
-6
-8
-10
Voltage (V)
Temperature error vs supply voltage (typical)
0.15
0.1
Temperature error (°C)
0.05
0
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
-0.05
-0.1
-0.15
Voltage (V)
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 10
MS5535C
14 bar Pressure Sensor Module
FUNCTION
GENERAL
The MS5535C consists of a piezo-resistive sensor and a sensor interface IC. The main function of the MS5535C is
to convert the uncompensated analogue output voltage from the piezo-resistive pressure sensor to a 16-bit digital
value, as well as providing a 16-bit digital value for the temperature of the sensor.
Measured pressure (16-bit)
“D1”
Measured temperature (16-bit)
“D2”
As the output voltage of a pressure sensor is strongly dependent on temperature and process tolerances, it is
necessary to compensate for these effects. This compensation procedure must be performed by software using an
external microcontroller.
D1
D2
Word1..4
Pressure
Calculation
in external
microcontroller
Temperature
Sensor
For both pressure and temperature measurement the same ADC is used (sigma delta converter):
•
•
for the pressure measurement, the differential output voltage from the pressure sensor is converted
for the temperature measurement, the sensor bridge resistor is sensed and converted
During both measurements the sensor will only be switched on for a very short time in order to reduce power
consumption. As both, the bridge bias and the reference voltage for the ADC are derived from V DD, the digital output
data is independent of the supply voltage.
FACTORY CALIBRATION
Every module is individually factory calibrated at two temperatures and two pressures. As a result, 6 coefficients
necessary to compensate for process variations and temperature variations are calculated and stored in the 64-bit
PROM of each module. These 64-bit (partitioned into four words of 16-bit) must be read by the microcontroller
software and used in the program converting D1 and D2 into compensated pressure and temperature values.
PRESSURE AND TEMPERATURE MEASUREMENT
The sequence of reading pressure and temperature as well as of performing the software compensation is depicted
in Fig. 3 and Fig. 5.
First Word1 to Word4 have to be read through the serial interface. This can be done once after reset of the
microcontroller that interfaces to the MS5535C. Next, the compensation coefficients C1 to C6 are extracted using
bit-wise logical- and shift-operations (refer to Fig. 4 for the bit-pattern of Word1 to Word4).
For the pressure measurement, the microcontroller has to read the 16-bit values for pressure (D1) and temperature
(D2) via the serial interface in a loop (for instance every second). Then, the compensated pressure is calculated
out of D1, D2 and C1 to C6 according to the algorithm in Fig. 3 (possibly using quadratic temperature compensation
according to Fig. 5). All calculations can be performed with signed 16-bit variables. Results of multiplications may
be up to 32-bit long (+sign). In the flow according to Fig. 3 a division follows each multiplication. This division can
be performed by bit-wise shifting (divisors are to the power of 2). It is ensured that the results of these divisions are
less than 65536 (16 bit).
For the timing of signals to read out Word1 to Word4, D1, and D2 please refer to the paragraph “Serial Interface".
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 11
MS5535C
14 bar Pressure Sensor Module
Basic equations:
System
initialisation
Start
Example:
Read calibration data (factory calibrated) from
PROM of MS5535C
Word1 = 18556
Word2 = 49183
Word3 = 22354
Word4 = 28083
Word1, Word2, Word3 and Word4 (4x16 Bit)
Convert calibration data into coefficients:
(see bit pattern of Word1-Word4)
C1: Pressure sensitivity
C2: Pressure offset
C3: Temperature coefficient of pressure sensitivity
C4: Temperature coefficient of pressure offset
C5: Reference temperature
C6: Temperature coefficient of the temperature
(13 Bit)
(13 Bit)
(10 Bit)
(9 Bit)
(12 Bit)
(7 Bit)
SENST1
OFFT1
TCS
TCO
Tref
TEMPSENS
C1 = 2319
C2 = 4864
C3 = 349
C4 = 219
C5 = 2002
C6 = 51
(Refer to application note AN519 for limits of coefficients and
Pressure and temperature measurement
calculated results)
Read digital pressure value from MS5535C
D1 (16 Bit)
D1 = 17788
Read digital temperature value from MS5535C
D2 (16 Bit)
D2 = 26603
Calculate calibration temperature
UT1 = 8*C5 + 10000
Calculate actual temperature
Difference between actual temperature and reference
temperature:
dT = D2 - UT1
Actual temperature:
dT(D2) = D2 - Tref
dT
TEMP(D2) = 20 + dT(D2) * TEMPSENS
TEMP = 243
= 24.3°C
OFF(D2) = OFFT1 + TCO*dT(D2)
OFF
SENS(D2) = SENST1 + TCS * dT(D2)
SENS = 4198
11
TEMP = 200 + dT*(C6+100)/2 (0.1°C resolution)
= 587
Calculate temperature compensated pressure
Offset at actual temperature:
OFF = C2 + (C4 - 250)*dT/212 + 10000
Sensitivity at actual temperature:
= 14859
SENS = C1/2 + (C3 + 200) )*dT/213 + 3000
Temperature compensated pressure:
P = SENS * (D1 - OFF))/212 + 1000
P(D1,D2) = SENS(D2) * (D1 – OFF(D2))
P
= 4001
= 4001mbar
Display pressure and temperature value
Fig. 3: Flow chart for pressure and temperature reading and software compensation
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 12
MS5535C
14 bar Pressure Sensor Module
NOTES
1) Readings of D2 can be done less frequently, but the display will be less stable in this case.
2) For a stable display of 1 mbar resolution, it is recommended to display the average of 8 subsequent
pressure values.
C1 (13 Bit)
Word 1
DB12
DB11
DB10
DB9
DB8
DB7
DB6
C2/I (3 Bit)
DB5
DB4
DB3
DB2
DB1
C2/II (10 Bit)
Word 2
DB9
DB8
DB7
DB6
DB5
DB4
DB9
DB8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB11
DB10
DB8
DB7
DB6
DB5
DB4
DB11
DB10
DB9
DB7
DB6
DB2
DB1
DB0
DB2
DB1
DB0
DB8
C5/II (6 Bit)
DB3
DB2
DB1
DB0
DB5
DB4
C4 (9 Bit)
Word 4
DB12
C5/I (6 Bit)
C3 (10 Bit)
Word 3
DB0
DB3
C6 (7 Bit)
DB3
DB2
DB1
DB1
DB6
DB5
DB4
DB3
Fig. 4: Arrangement (Bit-pattern) of calibration data in Word1 to Word4
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 13
MS5535C
14 bar Pressure Sensor Module
SECOND-ORDER TEMPERATURE COMPENSATION
In order to obtain full temperature accuracy over the whole temperature range, it is recommended to compensate
for the non-linearity of the output of the temperature sensor. This can be achieved by correcting the calculated
temperature and pressure by a second order correction factor. The second-order factors are calculated as follows:
dT  0
dT < 0
yes
yes
Low Temperatures
High Temperatures
dT2 = dT – (dT/128*dT/128)/2
dT2 = dT – (dT/128*dT/128)/8
Calculate temperature
11
TEMP = (200 + dT2*(C6+100)/2 ) (0.1°C)
Fig. 5: Flow chart for calculating the temperature and pressure to the optimum accuracy.
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 14
MS5535C
14 bar Pressure Sensor Module
SERIAL INTERFACE
The MS5535C communicates with microprocessors and other digital systems via a 3-wire synchronous serial
interface as shown in Fig. 1. The SCLK (Serial clock) signal initiates the communication and synchronizes the data
transfer with each bit being sampled by the MS5535C on the rising edge of SCLK and each bit being sent by the
MS5535C on the rising edge of SCLK. The data should thus be sampled by the microcontroller on the falling edge
of SCLK and sent to the MS5535C with the falling edge of SCLK. The SCLK-signal is generated by the
microprocessor’s system. The digital data provided by the MS5535C on the DOUT pin is either the conversion result
or the software calibration data. In addition, the signal DOUT (Data out) is also used to indicate the conversion
status (conversion-ready signal, see below). The selection of the output data is done by sending the corresponding
instruction on the pin DIN (Data input).
Following is a list of possible output data instructions:







Conversion start for pressure measurement and ADC-data-out
Conversion start for temperature measurement and ADC-data-out
Calibration data read-out sequence for Word1
Calibration data read-out sequence for Word2
Calibration data read-out sequence for Word3
Calibration data read-out sequence for Word4
RESET sequence
“D1”
“D2”
(Figure 6a)
(Figure 6b)
(Figure 6c)
(Figure 6d)
(Figure 6c)
(Figure 6d)
(Figure 6e)
Every communication starts with an instruction sequence at pin DIN. Fig. 6 shows the timing diagrams for the
MS5535C. The device does not need a ‘Chip select’ signal. Instead there is a START sequence (3-Bit high) before
each SETUP sequence and STOP sequence (3-Bit low) after each SETUP sequence. The SETUP sequence
consists in 4-Bit that select a reading of pressure, temperature or calibration data. In case of pressure- (D1) or
temperature- (D2) reading the module acknowledges the start of a conversion by a low to high transition at pin
DOUT.
Two additional clocks at SCLK are required after the acknowledge signal. Then SCLK is to be held low by the
microcontroller until a high to low transition on DOUT indicates the end of the conversion.
This signal can be used to create an interrupt in the microcontroller. The microcontroller may now read out the 16
bit word by giving another 17 clocks on the SLCK pin. It is possible to interrupt the data READOUT sequence with
a hold of the SCLK signal. It is important to always read out the last conversion result before starting a new
conversion.
The RESET sequence is special as the module in any state recognizes its unique pattern. By consequence, it can
be used to restart if synchronization between the microcontroller and the MS5535C has been lost. This sequence
is 21-bit long. The DOUT signal might change during that sequence (see Fig. 6e). It is recommended to send the
RESET sequence before each CONVERSION sequence to avoid hanging up the protocol permanently in case of
electrical interference.
DOUT SCLK
Conversion start for pressure measurement and ADC-data-out "D1":
end of conversion
start of conversion
conversion
(33ms)
ADC-data outMSB
DIN
DB7 DB6 DB5 DB4 DB3 DB2 DB1
ADC-data outLSB
DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
sequence: START+P-measurement
Bit0 Bit1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 Bit8 Bit9
Start-bit
Setup-bits
Stop-bit
Fig. 6a: D1 ACQUISITION sequence
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 15
MS5535C
DIN
DOUT SCLK
14 bar Pressure Sensor Module
Conversion start for temperature measurement and ADC-data-out "D2":
end of conversion
conversion
(33ms)
start of conversion
ADC-data outMSB
DB7 DB6 DB5 DB4 DB3 DB2 DB1
ADC-data outLSB
DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
sequence: START+T-measurement
Bit0 Bit1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 Bit8 Bit9
Start-bit
Setup-bits
Stop-bit
DIN
DOUT SCLK
Fig. 6b: D2 ACQUISITION sequence
Calibration data read out sequence for word 1/ word 3:
coefficient-data outMSB
DB7 DB6 DB5 DB4 DB3 DB2 DB1
coefficient-data outLSB
DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
sequence: coefficient read + address
Bit0 Bit1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 Bit8 Bit9Bit10Bit11
Start-bit
Stop-bit
Setup-bits
address word 1
address word 3
DIN
DOUT SCLK
Fig. 6c: Word1, Word3 READING sequence
Calibration data re ad out sequence for word 2/ word 4:
coefficient-data outMSB
DB7 DB6 DB5 DB4 DB3 DB2 DB1
coefficient-data outLSB
DB0 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0
sequence: coefficient read + address
Bit0 Bit1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 Bit8 Bit9 Bit10Bit11
Start-bit
Setup-bits
Stop-bit
address word 2
address word 4
DIN
DOUT SCLK
Fig. 6d: W2, W4 READING sequence
RESET - sequence:
sequence: RESET
Bit0 Bit1 Bit2 Bit3 Bit4 Bit5 Bit6 Bit7 Bit8 Bit9 Bit10Bit11Bit12Bit13Bit14Bit15Bit16Bit17Bit18Bit19Bit20
Fig. 6e: RESET sequence (21 bit)
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 16
MS5535C
14 bar Pressure Sensor Module
APPLICATION INFORMATION
GENERAL
The advantage for this combination of a sensor with a directly adapted integrated circuit is to save other external
components and to achieve very low power consumption. The main application field for this system includes
portable devices with battery supply, but its high accuracy and resolution make it also suited for industrial and
automotive applications. The possibility to compensate the sensor with software allows the user to adapt it to his
particular application. Communication between the MS5535C and the widely available microcontrollers is realised
over an easy-to-use 3-wire serial interface. Customers may select which microcontroller system to be used, and
there are no specific standard interface cells required, which may be of interest for specially designed 4 Bitmicrocontroller applications.
CALIBRATION
The MS5535C is factory calibrated. The calibration data is stored inside the 64 bit PROM memory.
SOLDERING
Please refer to the application note AN808 for all soldering issues.
HUMIDITY, WATER PROTECTION
The MS5535CM carries a metal protection cap filled with silicone gel for enhanced protection against humidity. The
properties of this gel ensure function of the sensor even when in direct water contact. This feature can be useful for
waterproof watches or other applications, where direct water contact cannot be avoided. Nevertheless the user
should avoid drying of hard materials like for example salt particles on the silicone gel surface. In this case it is
better to rinse with clean water afterwards. Special care has to be taken to not mechanically damage the gel.
Damaged gel could lead to air entrapment and consequently to unstable sensor signal, especially if the damage is
close to the sensor surface.
The metal protection cap is fabricated of special anticorrosive stainless steel in order to avoid any corrosive battery
effects inside the final product.
LIGHT SENSITIVITY
The MS5535C is sensitive to sunlight, especially to infrared light sources. This is due to the strong photo effect of
silicon. As the effect is reversible there will be no damage, but the user has to take care that in the final product the
sensor cannot be exposed to direct light during operation. This can be achieved for instance by placing mechanical
parts with holes in such that light cannot pass.
CONNECTION TO PCB
The package outline of the module allows the use of a flexible PCB to connect it. This can be important for
applications in watches and other special devices, and will also reduce mechanical stress on the device.
For applications subjected to mechanical shock, it is recommended to enhance the mechanical reliability of the
solder junctions by covering the rim or the corners of MS5535C's ceramic substrate with glue or Globtop-like
material.
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 17
MS5535C
14 bar Pressure Sensor Module
DECOUPLING CAPACITOR
Particular care must be taken when connecting the device to power supply. A 47 F tantalum capacitor must be
placed as close as possible of the MS5535C's VDD pin. This capacitor will stabilize the power supply during data
conversion and thus, provide the highest possible accuracy.
APPLICATION EXAMPLE: DIVING COMPUTER USING MS5535C
MS5535C is a circuit that can be used in connection with a microcontroller in diving computer applications. It is
designed for low-voltage systems with a supply voltage of 3V, particularly in battery applications. The MS5535C is
optimised for low current consumption as the AD-converter clock (MCLK) can use the 32.768 kHz frequency of a
standard watch crystal, which is supplied in most portable watch systems.
3V-Battery
LCD-Display
VDD
XTAL1
32.768 kHz
MS5535C
VDD
47µF
Tantal
XTAL2
Keypad
MCLK
DIN
DOUT
SCLK
GND
4/8bit-Microcontroller
GND
EEPROM
optional
Figure 7: Demonstration of MS5535C in a diving computer.
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 18
MS5535C
14 bar Pressure Sensor Module
DEVICE PACKAGE OUTLINES
Fig. 8: Device package outlines of MS5535-CM
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 19
MS5535C
14 bar Pressure Sensor Module
RECOMMENDED PAD LAYOUT
Pad layout for bottom side of MS5535C soldered onto printed circuit board.
Fig. 9: Layout for bottom side
Pad layout for top side of MS5535C soldered onto printed circuit board.
Fig. 10: Layout for topside
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 20
MS5535C
14 bar Pressure Sensor Module
ASSEMBLY
MECHANICAL STRESS
It is recommended to avoid mechanical stress on the PCB on which the sensor is mounted. The thickness of the
PCB should not be below 1.6 mm. A thicker PCB is stiffer creating less stress on the soldering contacts. For
applications where mechanical stress cannot be avoided (for example ultrasound welding of the case or thin PCB’s
in watches) please fix the sensor with drops of low stress epoxy (for example Hysol FP-4401) at the corners of the
sensor as shown below.
Fixing with Globtop
increases mechanical
stability
MOUNTING
The MS5535C can be placed with automatic Pick&Place equipment using vacuum nozzles. It will not be damaged
by the vacuum. Due to the low stress assembly the sensor does not show pressure hysteresis effects.
Special care has to be taken to not touch the protective gel of the sensor during the assembly.
The MS5535C can be mounted with the cap down or the cap looking upwards. In both cases it is important to solder
all contact pads. The Pins PEN and PV shall be left open or connected to VDD. Do not connect the Pins PEN and
PV to GND!
Solder at both sides to
increase mechanical
stability
Placement cap up
Placement cap down
(hole in PCB to fit cap)
SEALING WITH O-RING
In products like outdoor watches the electronics must be protected against direct water or humidity. For those
products the MS5535-CM provides the possibility to seal with an O-ring. The protective cap of the MS5535CM is
made of special anticorrosive stainless steel with a polished surface. In addition to this the MS5535CM is filled with
silicone gel covering the sensor and the bonding wires. The O-ring (or O-rings) shall be placed at the outer diameter
of the metal cap. This method avoids mechanical stress because the sensor can move in vertical direction.
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 21
MS5535C
14 bar Pressure Sensor Module
CLEANING
The MS5535C has been manufactured under cleanroom conditions. Each device has been inspected for the
homogeneity and the cleanness of the silicone gel. It is therefore recommended to assemble the sensor under class
10’000 or better conditions. Should this not be possible, it is recommended to protect the sensor opening during
assembly from entering particles and dust. To avoid cleaning of the PCB, solder paste of type “no-clean” shall be
used. Cleaning might damage the sensor!
ESD PRECAUTIONS
The electrical contact pads are protected against ESD up to 4 kV HBM (human body model). It is therefore essential
to ground machines and personal properly during assembly and handling of the device. The MS5535C is shipped
in antistatic transport boxes. Any test adapters or production transport boxes used during the assembly of the sensor
shall be of an equivalent antistatic material.
ORDERING INFORMATION
Product Code
MS5535-CM
Product
14 bar Pressure
Sensor Module with
gel
Art. No
325535009
Package
SMD hybrid with solder paste,
metal protection cap,
silicone gel sensor protection
Comments
Standard version
NORTH AMERICA
EUROPE
ASIA
Measurement Specialties, Inc.,
a TE Connectivity Company
45738 Northport Loop West
Fremont, CA 94538
Tel: +1 800 767 1888
Fax: +1 510 498 1578
e-mail: [email protected]
Website: www.meas-spec.com
Measurement Specialties (Europe), Ltd.,
a TE Connectivity Company
Switzerland Sàrl
Ch. Chapons-des-Prés 11
CH-2022 Bevaix
Tel: +41 32 847 9550
Fax: + 41 32 847 9569
e-mail: [email protected]
Website: www.meas-spec.com
Measurement Specialties (China), Ltd.,
a TE Connectivity Company
No. 26 Langshan Road
Shenzhen High-Tech Park (North) Nanshan
District, Shenzhen, 518057
China
Tel: +86 755 3330 5088
Fax: +86 755 3330 5099
e-mail: [email protected]
Website: www.meas-spec.com
TE.com/sensorsolutions
Measurement Specialties, Inc., a TE Connectivity company.
Measurement Specialties, TE Connectivity, TE Connectivity (logo) and EVERY CONNECTION COUNTS are trademarks. All other logos, products and/or company names referred to herein
might be trademarks of their respective owners.
The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, TE Connectivity makes
no warranties as to its accuracy or completeness and disclaims any liability in connection with its use. TE Connectivity‘s obligations shall only be as set forth in TE Connectivity‘s Standard
Terms and Conditions of Sale for this product and in no case will TE Connectivity be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse
of the product. Users of TE Connectivity products should make their own evaluation to determine the suitability of each such product for the specific application.
© 2015
TE Connectivity Ltd. family of companies
All Rights Reserved.
DA5535C_007
0005535C1195 ECN1511
SENSOR SOLUTIONS ///MS5535C
09/2015
Page 22
Similar pages