NLU1GT14 Single Schmitt-Trigger Inverter, TTL Level LSTTL-Compatible Inputs The NLU1GT14 MiniGatet is an advanced high-speed CMOS Schmitt-trigger inverter in ultra-small footprint. The device input is compatible with TTL-type input thresholds and the output has a full 5 V CMOS level output swing. The NLU1GT14 input and output structures provide protection when voltages up to 7 V are applied, regardless of the supply voltage. The NLU1GT14 can be used to enhance noise immunity or to square up slowly changing waveforms. http://onsemi.com MARKING DIAGRAMS UDFN6 MU SUFFIX CASE 517AA MM ULLGA6 1.0 x 1.0 CASE 613AD MM ULLGA6 1.2 x 1.0 CASE 613AE MM ULLGA6 1.45 x 1.0 CASE 613AF MM 1 Features •High Speed: tPD = 4.5 ns (Typ) @ VCC = 5.0 V •Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C •TTL-Compatible Input: VIL = 0.8 V; VIH = 2.0 V •CMOS-Compatible Output: 1 VOH > 0.8 VCC; VOL < 0.1 VCC @ Load •Power Down Protection Provided on inputs •Balanced Propagation Delays •Overvoltage Tolerant (OVT) Input and Output Pins •Ultra-Small Packages •These are Pb-Free Devices 1 1 NC 1 6 VCC IN A 2 5 NC 3 GND 4 M M PIN ASSIGNMENT OUT Y Figure 1. Pinout (Top View) IN A 1 = Device Marking = Date Code 1 NC 2 IN A 3 GND 4 OUT Y 5 NC 6 VCC FUNCTION TABLE OUT Y Figure 2. Logic Symbol A Y L H H L ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. © Semiconductor Components Industries, LLC, 2008 March, 2008 - Rev. 2 1 Publication Order Number: NLU1GT14/D NLU1GT14 MAXIMUM RATINGS Symbol Value Unit VCC DC Supply Voltage -0.5 to +7.0 V VIN DC Input Voltage -0.5 to +7.0 V DC Output Voltage -0.5 to +7.0 V VIN < GND -20 mA VOUT < GND ±20 mA VOUT Parameter IIK DC Input Diode Current IOK DC Output Diode Current IO DC Output Source/Sink Current ±12.5 mA ICC DC Supply Current Per Supply Pin ±25 mA IGND DC Ground Current per Ground Pin ±25 mA TSTG Storage Temperature Range -65 to +150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds 260 °C TJ Junction Temperature Under Bias 150 °C MSL FR VESD ILATCHUP Moisture Sensitivity Level 1 Flammability Rating Oxygen Index: 28 to 34 ESD Withstand Voltage UL 94 V-0 @ 0.125 in Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) Latchup Performance Above VCC and Below GND at 125°C (Note 5) > 2000 > 150 N/A V ±500 mA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2 ounce copper trace no air flow. 2. Tested to EIA / JESD22-A114-A. 3. Tested to EIA / JESD22-A115-A. 4. Tested to JESD22-C101-A. 5. Tested to EIA / JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 1.65 5.5 V VCC Positive DC Supply Voltage VIN Digital Input Voltage 0 5.5 V Output Voltage 0 5.5 V VOUT TA Operating Free-Air Temperature Dt/DV Input Transition Rise or Fall Rate VCC = 3.3 V ± 0.3 V VCC = 5.0 V ± 0.5 V http://onsemi.com 2 -55 +125 °C 0 0 No Limit No Limit ns/V NLU1GT14 DC ELECTRICAL CHARACTERISTICS Symbol Parameter Conditions TA = 25 5C VCC (V) Min Typ Max TA = +855C TA = -555C to +1255C Min Min VT+ Positive Threshold Voltage 3.0 4.5 5.5 1.20 1.58 1.79 1.40 1.74 1.94 1.60 2.00 2.10 VT- Negative Threshold Voltage 3.0 4.5 5.5 0.35 0.5 0.6 0.76 1.01 1.13 0.93 1.18 1.29 0.35 0.5 0.6 VH Hysteresis Voltage 3.0 4.5 5.5 0.30 0.40 0.50 0.64 0.73 0.81 1.20 1.40 1.60 0.30 0.40 0.50 2.0 3.0 4.5 1.9 2.9 4.4 2.0 3.0 4.5 3.0 4.5 2.58 3.94 VOH VIN v VT-MIN IOH = -50 mA Minimum High-Level Output Voltage VIN v VT-MIN IOH = -4 mA IOH = -8 mA VOL Maximum Low-Level Output Voltage VIN w VT+MAX IOL = 50 mA 2.0 3.0 4.5 VIN w VT+MAX IOL = 4 mA IOL = 8 mA 3.0 4.5 0 0 0 Max 1.6 2.0 2.0 Max Unit 1.6 2.0 2.0 V 0.35 0.5 0.6 1.20 1.40 1.60 0.30 0.40 0.50 1.9 2.9 4.4 1.9 2.9 4.4 2.48 3.80 2.34 3.66 V 1.20 1.40 1.60 V V 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.36 0.36 0.44 0.44 0.52 0.52 V IIN Input Leakage Current 0 v VIN v 5.5 V 0 to 5.5 ±0.1 ±1.0 ±1.0 mA ICC Quiescent Supply Current 0 v VIN v VCC 5.5 1.0 20 40 mA ICCT Quiescent Supply Current VIN = 3.4 V 5.5 1.35 1.50 1.65 mA IOPD Output Leakage Current VOUT = 5.5 V 0.0 0.5 5.0 10 mA AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) TA = 25 5C TA = +855C TA = -555C to +1255C Symbol Parameter VCC (V) Test Condition Typ Max Min Max Min Max Unit tPLH, tPHL Propagation Delay, Input A to Output Y 3.0 to 3.6 CL = 15 pF 7.0 12.8 1.0 15.0 1.0 17.0 ns CL = 50 pF 8.4 16.3 1.0 18.5 1.0 20.5 4.5 to 5.5 CL = 15 pF 4.5 8.6 1.0 10.0 1.0 11.5 CL = 50 pF 5.8 10.6 1.0 12.0 1.0 13.5 5 10 CIN Input Capacitance CPD Power Dissipation Capacitance (Note 6) Min 5.0 10.0 10 10.0 pF pF 6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the dynamic operating current consumption without load. Average operating current can be obtained by the equation ICC(OPR) = CPD • VCC • fin + ICC. CPD is used to determine the no-load dynamic power consumption: PD = CPD • VCC2 • fin + ICC • VCC. http://onsemi.com 3 NLU1GT14 OUTPUT INPUT VCC A or B 50% CL* GND tPLH Y tPHL 50% VCC *Includes all probe and jig capacitance. A 1-MHz square input wave is recommended for propagation delay tests. Figure 3. Switching Waveforms Figure 4. Test Circuit VH VCC VT+ VT- VIN VCC VH VT+ VT- VIN GND GND VOH VOH VOUT Vout VOL VOL (a) A Schmitt-Trigger Squares Up Inputs With Slow Rise and Fall Times (b) A Schmitt-Trigger Offers Maximum Noise Immunity Figure 5. Typical Schmitt-Trigger Applications ORDERING INFORMATION Package Shipping† UDFN6 (Pb-Free) 3000 / Tape & Reel NLU1GT14AMX1TCG ULLGA6, 1.45 x 1.0, 0.5P (Pb-Free) 3000 / Tape & Reel NLU1GT14BMX1TCG ULLGA6, 1.2 x 1.0, 0.4P (Pb-Free) 3000 / Tape & Reel NLU1GT14CMX1TCG ULLGA6, 1.0 x 1.0, 0.35P (Pb-Free) 3000 / Tape & Reel Device NLU1GT14MUTCG †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 4 NLU1GT14 PACKAGE DIMENSIONS UDFN6, 1.2x1.0, 0.4P CASE 517AA-01 ISSUE C EDGE OF PACKAGE PIN ONE REFERENCE 2X 0.10 C ÉÉ ÉÉ ÉÉ L1 E DETAIL A Bottom View (Optional) TOP VIEW 2X EXPOSED Cu 0.10 C (A3) 0.10 C A1 A 10X 0.08 C ÉÉÉ ÉÉÉ A3 DETAIL B Side View (Optional) 5X MILLIMETERS MIN MAX 0.45 0.55 0.00 0.05 0.127 REF 0.15 0.25 1.20 BSC 1.00 BSC 0.40 BSC 0.30 0.40 0.00 0.15 0.40 0.50 MOUNTING FOOTPRINT* 6X 6X 0.42 C A1 DIM A A1 A3 b D E e L L1 L2 MOLD CMPD SEATING PLANE SIDE VIEW 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 mm FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. A B D 0.22 L 3 L2 6X b 0.10 C A B 0.05 C 6 0.40 PITCH 4 e NOTE 3 1.07 DIMENSIONS: MILLIMETERS BOTTOM VIEW *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 5 NLU1GT14 PACKAGE DIMENSIONS ULLGA6 1.0x1.0, 0.35P CASE 613AD-01 ISSUE A PIN ONE REFERENCE 0.10 C ÉÉ ÉÉ ÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW C A1 MILLIMETERS MIN MAX --0.40 0.00 0.05 0.12 0.22 1.00 BSC 1.00 BSC 0.35 BSC 0.25 0.35 0.30 0.40 5X 0.48 6X 0.22 e 5X L NOTE 4 3 1 1.18 L1 0.53 6 4 6X b 0.35 PITCH DIMENSIONS: MILLIMETERS 0.10 C A B BOTTOM VIEW 1 PKG OUTLINE 0.05 C NOTE 3 *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 6 NLU1GT14 PACKAGE DIMENSIONS ULLGA6 1.2x1.0, 0.4P CASE 613AE-01 ISSUE A PIN ONE REFERENCE 0.10 C ÉÉ ÉÉ ÉÉ 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D E DIM A A1 b D E e L L1 TOP VIEW 0.05 C A 6X 0.05 C SEATING PLANE SIDE VIEW MOUNTING FOOTPRINT SOLDERMASK DEFINED* C A1 MILLIMETERS MIN MAX --0.40 0.00 0.05 0.15 0.25 1.20 BSC 1.00 BSC 0.40 BSC 0.25 0.35 0.35 0.45 5X 0.49 e 5X L NOTE 4 3 1 6X 0.26 1.24 L1 0.53 6 4 6X b 0.10 C A B BOTTOM VIEW 0.05 C NOTE 3 1 PKG OUTLINE 0.40 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 7 NLU1GT14 PACKAGE DIMENSIONS ULLGA6 1.45x1.0, 0.5P CASE 613AF-01 ISSUE A PIN ONE REFERENCE 0.10 C NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.15 AND 0.30 mm FROM THE TERMINAL TIP. 4. A MAXIMUM OF 0.05 PULL BACK OF THE PLATED TERMINAL FROM THE EDGE OF THE PACKAGE IS ALLOWED. A B D ÉÉÉ ÉÉÉ ÉÉÉ E DIM A A1 b D E e L L1 TOP VIEW 0.10 C 0.05 C A 6X 0.05 C MOUNTING FOOTPRINT SOLDERMASK DEFINED* SEATING PLANE SIDE VIEW 5X C A1 e 5X L MILLIMETERS MIN MAX --0.40 0.00 0.05 0.15 0.25 1.45 BSC 1.00 BSC 0.50 BSC 0.25 0.35 0.30 0.40 0.49 NOTE 4 3 1 6X 0.30 1.24 L1 0.53 6 4 BOTTOM VIEW 6X b 0.10 C A B 0.05 C NOTE 3 1 PKG OUTLINE 0.50 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. MiniGate is a trademark of Semiconductor Components Industries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NLU1GT14/D