LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 LM25085, LM25085-Q1 42V Constant On-Time PFET Buck Switching Controller Check for Samples: LM25085, LM25085-Q1 FEATURES PACKAGE • • • • 1 2 • • • • • • • • • • • • LM25085-Q1 is an Automotive Grade product that is AEC-Q100 Grade 1 Qualified (-40°C to 125°C Operating Junction Temperature) Wide 4.5V to 42V Input Voltage Range Adjustable Current Limit Using RDS(ON) or a Current Sense Resistor Programmable Switching Frequency to 1MHz No Loop Compensation Required Ultra-Fast Transient Response Nearly Constant Operating Frequency with Line and Load Variations Adjustable Output Voltage from 1.25V Precision ±2% Feedback Reference Capable of 100% Duty Cycle Operation Internal Soft-Start Timer Integrated High Voltage Bias Regulator Thermal Shutdown HVSSOP-8 VSSOP-8 WSON-8 (3mm x 3mm) DESCRIPTION The LM25085 is a high efficiency PFET switching regulator controller that can be used to quickly and easily develop a small, efficient buck regulator for a wide range of applications. This high voltage controller contains a PFET gate driver and a high voltage bias regulator which operates over a wide 4.5V to 42V input range. The constant on-time regulation principle requires no loop compensation, simplifies circuit implementation, and results in ultrafast load transient response. The operating frequency remains nearly constant with line and load variations due to the inverse relationship between the input voltage and the on-time. The PFET architecture allows 100% duty cycle operation for a low dropout voltage. Either the RDS(ON) of the PFET or an external sense resistor can be used to sense current for overcurrent detection. Typical Application, Basic Step Down Controller 4.5V to 42V Input CVCC LM25085 VIN VIN VCC CADJ CIN ADJ GND RT RADJ L1 PGATE Q1 SHUTDOWN RT VOUT ISEN D1 GND Cff COUT RFB2 GND FB RFB1 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008–2013, Texas Instruments Incorporated LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com Connection Diagram Exposed Pad on Bottom Connect to Ground 8 VIN 2 7 VCC FB 3 6 PGATE GND 4 5 ISEN 1 ADJ RT ADJ 1 8 VIN RT 2 7 VCC FB 3 6 PGATE GND 4 5 ISEN Exposed Pad on Bottom Connect to Ground Figure 1. Top View 8-Lead HVSSOP-PowerPAD See Package Number DGN0008A Figure 3. Top View 8-Lead WSON See Package Number NGQ0008A ADJ 1 8 VIN RT 2 7 VCC FB 3 6 PGATE GND 4 5 ISEN Figure 2. Top View 8-Lead VSSOP See Package Number DGK0008A PIN DESCRIPTIONS Pin No. Name 1 Description Application Information ADJ Current Limit Adjust The current limit threshold is set by an external resistor from VIN to ADJ in conjunction with the external sense resistor or the PFET’s RDS(ON). 2 RT On-time control and shutdown An external resistor from VIN to RT sets the buck switch on-time and switching frequency. Grounding this pin shuts down the controller. 3 FB Voltage Feedback from the regulated output Input to the regulation and over-voltage comparators. The regulation level is 1.25V. 4 GND Circuit Ground Ground reference for all internal circuitry 5 ISEN Current sense input for current limit detection. Connect to the PFET drain when using RDS(ON) current sense. Connect to the PFET source and the sense resistor when using a current sense resistor. 6 PGATE Gate Driver Output Connect to the gate of the external PFET. 7 VCC Output of the gate driver bias regulator Output of the negative voltage regulator (relative to VIN) that biases the PFET gate driver. A low ESR capacitor is required from VIN to VCC, located as close as possible to the pins. 8 VIN Input supply voltage The operating input range is from 4.5V to 42V. A low ESR bypass capacitor must be located as close as possible to the VIN and GND pins. EP Exposed Pad Exposed pad on the underside of the package (HVSSOP-PowerPAD-8 and WSON only). This pad is to be soldered to the PC board ground plane to aid in heat dissipation. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 Absolute Maximum Ratings (1) (2) VIN to GND -0.3V to 45V ISEN to GND -0.3V to VIN + 0.3V ADJ to GND -0.3V to VIN + 0.3V RT, FB to GND -0.3V to 7V VIN to VCC, VIN to PGATE -0.3V to 10V ESD Rating (3) Human Body Model 2kV Storage Temperature Range (1) (2) (3) -65°C to +150°C Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For specifications and test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin. Operating Ratings (1) VIN Voltage 4.5V to 42V −40°C to + 125°C Junction Temperature (1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is intended to be functional. For specifications and test conditions, see the Electrical Characteristics. Electrical Characteristics Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 24V, RT = 100kΩ. Symbol Parameter Conditions Min IIN Operating Current Non-Switching, FB = 1.4V IQ Shutdown Current RT = 0V VIN - VCC Vin = 9V, FB = 1.4V, ICC = 0mA Typ Max Units 1.25 1.75 mA 175 300 µA 7.7 8.5 V VIN Pin VCC Regulator (1) (1) (2) VCC(reg) 6.9 Vin = 9V, FB = 1.4V, ICC = 20mA 7.7 V Vin = 42V, FB = 1.4V, ICC = 0mA 7.7 V VCC Under-Voltage Lock-Out Threshold VCC Increasing 3.8 V UVLOVcc Hysteresis VCC Decreasing 260 mV VCC Current Limit FB = 1.4V 20 40 mA VPGATE(HI) PGATE High Voltage PGATE Pin = Open VIN -0.1 VIN V VPGATE(LO) UVLOVcc VCC(CL) PGATE Pin PGATE Low Voltage PGATE Pin = Open VPGATE(HI)4.5 PGATE High Voltage at Vin = 4.5V PGATE Pin = Open VPGATE(LO)4.5 PGATE Low Voltage at Vin = 4.5V PGATE Pin = Open VCC Driver Output Source Current VIN = 12V, PGATE = VIN - 3.5V 1.75 Driver Output Sink Current VIN = 12V, PGATE = VIN - 3.5V 1.5 A Driver Output Resistance Source current = 500mA 2.3 Ω Sink current = 500mA 2.3 Ω IPGATE RPGATE VCC VIN -0.1 VCC+0.1 VIN V V VCC+0.1 V A Current Limit Detection IADJ VCL (1) (2) OFFSET ADJUST Pin Current Source VADJ = 22.5V 32 40 48 µA Current Limit Comparator Offset VADJ = 22.5V, VADJ - VISEN -9 0 9 mV Operating current and shutdown current do not include the current in the RT resistor. VCC provides self bias for the internal gate drive. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 3 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com Electrical Characteristics (continued) Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C to +125°C. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the following conditions apply: VIN = 24V, RT = 100kΩ. Symbol Parameter Conditions RTSD Shutdown Threshold RT Pin Voltage Rising RTHYS Shutdown Threshold Hysteresis Min Typ Max Units RT Pin 0.73 V 50 mV On-Time tON – 1 On-Time tON – 2 tON - 3 tON - 4 Minimum On-Time in Current Limit (3) VIN = 4.5V, RT = 100kΩ 3.5 5 7.15 µs VIN = 24V, RT = 100kΩ 560 720 870 ns VIN = 42V, RT = 100kΩ 329 415 500 ns VIN = 24V, 25mV Overdrive at ISEN 55 140 235 ns Off-Time tOFF(CL1) Off-Time (Current Limit) (3) VIN = 12V, VFB = 0V 5.35 7.9 10.84 µs tOFF(CL2) VIN = 12V, VFB = 1V 1.42 1.9 3.03 µs tOFF(CL3) VIN = 24V, VFB = 0V 8.9 13 17.7 µs tOFF(CL4) VIN = 24V, VFB = 1V 2.22 3.2 4.68 µs 1.225 1.25 1.275 V Regulation and Over-Voltage Comparators (FB Pin) VREF FB Regulation Threshold VOV FB Over-Voltage Threshold IFB FB Bias Current Measured With Respect to VREF 350 mV 10 nA Soft-Start Function tSS Soft-Start Time 1.4 2.5 4.3 ms Thermal Shutdown TSD Junction Shutdown Temperature THYS Junction Shutdown Hysteresis Thermal Resistance θJA θJC (3) (4) (5) 4 Junction Temperature Rising 170 °C 20 °C VSSOP-8 package 126 °C/W HVSSOP-PowerPAD-8 package 46 WSON-8 package 54 (4) Junction to Ambient, 0 LFPM Air Flow (5) Junction to Case, 0 LFPM Air Flow (5) VSSOP-8 package 29 HVSSOP-PowerPAD-8 package 5.5 WSON-8 package 9.1 °C/W The tolerance of the minimum on-time (tON-4) and the current limit off-times (tOFF(CL1) through (tOFF(CL4)) track each other over process and temperature variations. A device which has an on-time at the high end of the range will have an off-time that is at the high end of its range. For detailed information on soldering plastic VSSOP and WSON packages visit www.ti.com/packaging. Tested on a 4 layer JEDEC board. Four vias provided under the exposed pad. See JEDEC standards JESD51-5 and JESD51-7. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 Typical Performance Characteristics Unless otherwise specified the following conditions apply: TJ = 25°C, VIN = 24V. Efficiency (Circuit of Figure 28) Input Operating Current vs. VIN Figure 4. Figure 5. Shutdown Current vs. VIN VCC vs. VIN Figure 6. Figure 7. VCC vs. ICC On-Time vs. RT and VIN Figure 8. Figure 9. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 5 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Unless otherwise specified the following conditions apply: TJ = 25°C, VIN = 24V. 6 Off-Time vs. VIN and VFB Voltage at the RT Pin Figure 10. Figure 11. ADJ Pin Current vs. VIN Input Operating Current vs. Temperature Figure 12. Figure 13. Shutdown Current vs. Temperature VCC vs. Temperature Figure 14. Figure 15. Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 Typical Performance Characteristics (continued) Unless otherwise specified the following conditions apply: TJ = 25°C, VIN = 24V. On-Time vs. Temperature Minimum On-Time vs. Temperature Figure 16. Figure 17. Off-Time vs. Temperature Current Limit Comparator Offset vs. Temperature Figure 18. Figure 19. ADJ Pin Current vs. Temperature PGATE Driver Output Resistance vs. Temperature Figure 20. Figure 21. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 7 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Unless otherwise specified the following conditions apply: TJ = 25°C, VIN = 24V. Feedback Reference Voltage vs. Temperature Soft-Start Time vs. Temperature Figure 22. Figure 23. RT Pin Shutdown Threshold vs. Temperature Figure 24. 8 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 Block Diagram 4.5V to 42V Input VIN Negative Bias Regulator VIN CIN GND 7.7V CBYP LM25085 + - 0.73V RT + CVCC CADJ Thermal Shutdown RT + VCC VIN RADJ VCC UVLO ON Time One-Shot Gate Driver RSEN PGATE Q1 SHUTDOWN VCC 1.25V Soft-Start Gate Driver Control Logic L1 ADJ COUT 40 PA + QS - R REGULATION COMPARATOR 1.6V - GND OFF Time One-Shot + OVER-VOLTAGE COMPARATOR VOUT R3 C1 D1 + - C2 RFB2 ISEN RFB1 CURRENT LIMIT COMPARATOR VIN FB Sense resistor method shown for current limit detection. Minimum output ripple configuration shown. FUNCTIONAL DESCRIPTION OVERVIEW The LM25085 is a PFET buck (step-down) DC-DC controller using the constant on-time (COT) control principle. The input operating voltage range of the LM25085 is 4.5V to 42V. The use of a PFET in a buck regulator greatly simplifies the gate drive requirements and allows for 100% duty cycle operation to extend the regulation range when operating at low input voltage. However, PFET transistors typically have higher on-resistance and gate charge when compared to similarly rated NFET transistors. Consideration of available PFETs, input voltage range, gate drive capability of the LM25085, and thermal resistances indicate an upper limit of 10A for the load current for LM25085 applications. Constant on-time control is implemented using an on-time one-shot that is triggered by the feedback signal. During the off-time, when the PFET (Q1) is off, the load current is supplied by the inductor and the output capacitor. As the output voltage falls, the voltage at the feedback comparator input (FB) falls below the regulation threshold. When this occurs Q1 is turned on for the one-shot period which is determined by the input voltage (VIN) and the RT resistor. During the on-time the increasing inductor current increases the voltage at FB above the feedback comparator threshold. For a buck regulator the basic relationship between the on-time, off-time, input voltage and output voltage is: Duty Cycle = VOUT VIN = tON tON + tOFF = tON x FS where • Fs is the switching frequency (1) Equation 1 is valid only in continuous conduction mode (inductor current does not reach zero). Since the LM25085 controls the on-time inversely proportional to VIN, the switching frequency remains relatively constant as VIN is varied. If the input voltage falls to a level that is equal to or less than the regulated output voltage Q1 is held on continuously (100% duty cycle) and VOUT is approximately equal to VIN. The COT control scheme, with the feedback signal applied to a comparator rather than an error amplifier, requires no loop compensation, resulting in very fast load transient response. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 9 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com The LM25085 is available in both an 8 pin HVSSOP-PowerPAD package and an 8 pin WSON package with an exposed pad to aid in heat dissipation. An 8 pin VSSOP package without an exposed pad is also available. REGULATION CONTROL CIRCUIT The LM25085 buck DC-DC controller employs a control scheme based on a comparator and a one-shot ontimer, with the output voltage feedback compared to an internal reference voltage (1.25V). When the FB pin voltage falls below the feedback reference, Q1 is switched on for a time period determined by the input voltage and a programming resistor (RT). Following the on-time Q1 remains off until the FB voltage falls below the reference. Q1 is then switched on for another on-time period. The output voltage is set by the feedback resistors (RFB1, RFB2 in Block Diagram). The regulated output voltage is calculated as follows: VOUT = 1.25V x (RFB2+ RFB1)/ RFB1 (2) The feedback voltage supplied to the FB pin is applied to a comparator rather than a linear amplifier. For proper operation sufficient ripple amplitude is necessary at the FB pin to switch the comparator at regular intervals with minimum delay and noise susceptibility. This ripple is normally obtained from the output voltage ripple attenuated through the feedback resistors. The output voltage ripple is a result of the inductor’s ripple current passing through the output capacitor’s ESR, or through a resistor in series with the output capacitor. Multiple methods are available to ensure sufficient ripple is supplied to the FB pin, and three different configurations are discussed in Applications Information. When in regulation, the LM25085 operates in continuous conduction mode at medium to heavy load currents and discontinuous conduction mode at light load currents. In continuous conduction mode the inductor’s current is always greater than zero, and the operating frequency remains relatively constant with load and line variations. The minimum load current for continuous conduction mode is one-half the inductor’s ripple current amplitude. In discontinuous conduction mode, where the inductor’s current reaches zero during the off-time, the operating frequency is lower than in continuous conduction mode and varies with load current. Conversion efficiency is maintained at light loads since the switching losses are reduced with the reduction in load and frequency. If the voltage at the FB pin exceeds 1.6V due to a transient overshoot or excessive ripple at VOUT the internal over-voltage comparator immediately switches off Q1. The next on-time period starts when the voltage at FB falls below the feedback reference voltage. ON-TIME TIMER The on-time of the PFET gate drive output (PGATE pin) is determined by the resistor (RT) and the input voltage (VIN), and is calculated from: -7 tON = 1.45 x 10 x (RT + 1.4) (VIN - 1.56V + RT/3167) + 50 ns where • RT is in kΩ (3) The minimum on-time, which occurs at maximum VIN, should not be set less than 150ns (see CURRENT LIMITING). The buck regulator effective on-time, measured at the SW node (junction of Q1, L1, and D1) is typically longer than that calculated in Equation 3 due to the asymmetric delay of the PFET. The on-time difference caused by the PFET switching delay can be estimated as the difference of the turn-off and turn-on delays listed in the PFET data sheet. Measuring the difference between the on-time at the PGATE pin versus the SW node in the actual application circuit is also recommended. In continuous conduction mode, the inverse relationship of tON with VIN results in a nearly constant switching frequency as VIN is varied. The operating frequency can be calculated from: FS = VOUT x (VIN - 1.56V + RT/3167) -7 VIN x [(1.45 x 10 x (RT + 1.4)) + (tD x (VIN - 1.56V + RT/3167))] where • • 10 RT is in kΩ tD is equal to 50ns plus the PFET’s delay difference Submit Documentation Feedback (4) Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 To set a specific continuous conduction mode switching frequency (FS), the RT resistor is determined from the following: where • RT is in kΩ (5) A simplified version of Equation 5 at VIN = 12V, and tD = 100ns, is: RT = VOUT x 6 x 106 - 8.6 FS For VIN = 42V and tD = 100ns, the simplified equation is: SHUTDOWN The LM25085 can be shutdown by grounding the RT pin (see Figure 25). In this mode the PFET is held off, and the VCC regulator is disabled. The internal operating current is reduced to the value shown in Figure 6. The shutdown threshold at the RT pin is ≊0.73V, with ≊50mV of hysteresis. Releasing the pin enables normal operation. The RT pin must not be forced high during normal operation. VIN Input Voltage LM25085 RT RT STOP RUN Figure 25. Shutdown Implementation CURRENT LIMITING The LM25085 current limiting operates by sensing the voltage across either the RDS(ON) of Q1, or a sense resistor, during the on-time and comparing it to the voltage across the resistor RADJ (see Figure 26). The current limit function is much more accurate and stable over temperature when a sense resistor is used. The RDS(ON) of a MOSFET has a wide process variation and a large temperature coefficient. If the voltage across RDS(ON) of Q1, or the sense resistor, is greater than the voltage across RADJ, the current limit comparator switches to turn off Q1. Current sensing is disabled for a blanking time of ≊100ns at the beginning of the on-time to prevent false triggering of the current limit comparator due to leading edge current spikes. Because of the blanking time and the turn-on and turn-off delays created by the PFET, the on-time at the PGATE pin should not be set less than 150ns. An on-time shorter than that may prevent the current limit detection circuit from properly detecting an over-current condition. The duration of the subsequent forced off-time is a function of the input voltage and the voltage at the FB pin, as shown in Figure 10. The longer-than-normal forced off-time allows the inductor current to decrease to a low level before the next on-time. This cycle-by-cycle monitoring, followed by a forced off-time, provides effective protection from output load faults over a wide range of operating conditions. The voltage across the RADJ resistor is set by an internal 40µA current sink at the ADJ pin. When using Q1’s RDS(ON) for sensing, the current at which the current limit comparator switches is calculated from: ICL = 40µA x RADJ/RDS(ON) (6) When using a sense resistor (RSEN) the threshold of the current limit comparator is calculated from: Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 11 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com ICL = 40µA x RADJ/RSEN (7) When using Equation 6 or Equation 7, the tolerances for the ADJ pin current sink and the offset of the current limit comparator should be included to ensure the resulting minimum current limit is not less than the required maximum switch current. Simultaneously increasing the values of RADJ and RSEN decreases the effects of the current limit comparator offset, but at the expense of higher power dissipation. When using a sense resistor, the RSEN resistor value should be chosen within the practical limitations of power dissipation and physical size. For example, for a 10A current limit, setting RSEN = 0.005Ω results in a power dissipation as high as 0.5W. Current sense connections to the RSEN resistor, or to Q1, must be Kelvin connections to ensure accuracy. The CADJ capacitor filters noise from the ADJ pin, and helps prevent unintended switching of the current limit comparator due to input voltage transients. The recommended value for CADJ is 1000pF. CURRENT LIMIT OFF-TIME When the current through Q1 exceeds the current limit threshold, the LM25085 forces an off-time longer than the normal off-time defined by Equation 1. See Figure 10 or calculate the current limit off-time from the following equation: where • • VIN is the input voltage VFB is the voltage at the FB pin at the time current limit was detected (8) This feature is necessary to allow the inductor current to decrease sufficiently to offset the current increase which occurred during the on-time. During the on-time, the inductor current increases an amount equal to: (VIN - VOUT) x tON 'I = L (9) During the off-time the inductor current decreases due to the reverse voltage applied across the inductor by the output voltage, the freewheeling diode’s forward voltage (VFD), and the voltage drop due to the inductor’s series resistance (VESR). The current decrease is equal to: 'I = (VOUT + VFD + VESR) x tOFF L (10) The on-time in Equation 9 is shorter than the normal on-time since the PFET is shut off when the current limit threshold is crossed. If the off-time is not long enough, such that the current decrease (Equation 10) is less than the current increase (Equation 9), the current levels are higher at the start of the next on-time. This results in a further decrease in on-time, since the current limit threshold is crossed sooner. A balance is reached when the current changes in Equation 9 and Equation 10 are equal. The worst case situation is that of a direct short circuit at the output terminals, where VOUT = 0V, as that results in the largest current increase during the on-time, and the smallest decrease during the off-time. The sum of the diode’s forward voltage and the inductor’s ESR voltage must be sufficient to ensure current runaway does not occur. Using Equation 9 and Equation 10, this requirement can be stated as: VFD + VESR t VIN x tON tOFF (11) For tON in Equation 11 use the minimum on-time at the SW node. To determine this time period add the “Minimum on-time in current limit” specified in Electrical Characteristics (tON-4) to the difference of the turn-off and turn-on delays of the PFET. For tOFF use the value in Figure 10 or use Equation 8, where VFB is equal to zero volts. When using the minimum or maximum limits of those specifications to determine worst case situations, the tolerance of the minimum on-time (tON-4) and the current limit off-times (tOFF(CL1) through tOFF(CL4)) track each other over the process and temperature variations. A device which has an on-time at the high end of the range will have an off-time that is at the high end of its range. 12 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 LM25085 ADJ VIN LM25085 RADJ ADJ 40 PA 40 PA CURRENT LIMIT COMPARATOR + - VIN RADJ CURRENT LIMIT COMPARATOR CADJ + - ISEN VIN GATE DRIVER Q1 PGATE VCC RSEN CADJ ISEN VIN L1 GATE DRIVER Q1 PGATE L1 VCC D1 USING Q1 RDS(ON) D1 USING SENSE RESISTOR RSEN Figure 26. Current Limit Sensing VCC REGULATOR The VCC regulator provides a regulated voltage between the VIN and the VCC pins to provide the bias and gate current for the PFET gate driver. The 0.47µF capacitor at the VCC pin must be a low ESR capacitor, preferably ceramic as it provides the high surge current for the PFET’s gate at each turn-on. The capacitor must be located as close as possible to the VIN and VCC pins to minimize inductance in the PC board traces. Referring to Figure 7, the voltage across the VCC regulator (VIN – VCC) is equal to VIN until VIN reaches approximately 8.5V. At higher values of VIN, the voltage at the VCC pin is regulated at approximately 7.7V below VIN. If VIN drops below about 8V due to voltage transients, the VCC pin can be pulled down below GND. To prevent the negative VCC voltage from disturbing the internal circuit and causing abnormal operation, a Schottky diode is recommended between VCC pin and GND pin. The VCC regulator has a maximum current capability of at least 20mA. The regulator is disabled when the LM25085 is shutdown using the RT pin, or when the thermal shutdown is activated. PGATE DRIVER OUTPUT The PGATE pin output swings between VIN (Q1 off) and the VCC pin voltage (Q1 on). The rise and fall times depend on the PFET gate capacitance and the source and sink currents provided by the internal gate driver. See Electrical Characteristics for the current capability of the driver. P-CHANNEL MOSFET SELECTION The PFET must be rated for the maximum input voltage, with some margin above that to allow for transients and ringing which can occur on the supply line and the switching node. The gate-to-source voltage (VGS) normally provided to the PFET is 7.7V for VIN greater than 8.5V. However, if the circuit is to be operated at lower values of VIN, the selected PFET must be able to fully turn-on with a VGS voltage equal to VIN. The minimum input operating voltage for the LM25085 is 4.5V. Similar to NFETs, the case or exposed thermal pad for a PFET is electrically connected to the drain terminal. When designing a PFET buck regulator the drain terminal is connected to the switching node. This situation requires a trade-off between thermal and EMI performance since increasing the PC board area of the switching node to aid the PFET power dissipation also increases radiated noise, possibly disrupting the circuit operation. Typically the switching node area is kept to a reasonable minimum and the PFET peak current is derated to stay within the recommended temperature rating of the PFET. The RDS(ON) of the PFET determines a portion of the power dissipation in the PFET. However, PFETs with very low RDS(ON) usually have large values of gate charge. A PFET with a higher gate charge has a corresponding slower switching speed, leading to higher switching losses and affecting the PFET power dissipation. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 13 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com If the PFET RDS(ON) is used for current limit detection, note that it typically has a positive temperature coefficient. At 100°C the RDS(ON) may be as much as 50% higher than the value at 25°C which could result in incorrect current limiting if not accounted for when determining the value of the RADJ resistor. The PFET Total Gate Charge determines most of the power dissipation in the LM25085 due to the repetitive charge and discharge of the PFET’s gate capacitance by the gate driver (powered from the VCC regulator). The LM25085’s internal power dissipation can be calculated from the following: PDISS = VIN x ((QG x FS) + IIN) where • • • QG is the PFET Total Gate Charge obtained from its datasheet FS is the switching frequency IIN is the LM25085's operating current obtained from Figure 5 (12) Using the Thermal Resistance specifications in Electrical Characteristics, the approximate junction temperature can be determined. If the calculated junction temperature is near the maximum operating temperature of 125°C, either the switching frequency must be reduced, or a PFET with a smaller Total Gate Charge must be used. SOFT-START The internal soft-start feature of the LM25085 allows the regulator to gradually reach a steady state operating point at power up, thereby reducing startup stresses and current surges. Upon turn-on, when VCC reaches its under-voltage lockout threshold, the internal soft-start circuit ramps the feedback reference voltage from 0V to 1.25V, causing VOUT to ramp up in a proportional manner. The soft-start ramp time is typically 2.5ms. In addition to controlling the initial power up cycle, the soft-start circuit also activates when the LM25085 is enabled by releasing the RT pin, and when the circuit is shutdown and restarted by the internal Thermal Shutdown circuit. If the voltage at FB is below the regulation threshold value due to an over-current condition or a short circuit at VOUT, the internal reference voltage provided by the soft-start circuit to the regulation comparator is reduced along with FB. When the over-current or short circuit condition is removed, VOUT returns to the regulated value at a rate determined by the soft-start ramp. This feature helps prevent the output voltage from overshooting following an overload event. THERMAL SHUTDOWN The LM25085 should be operated such that the junction temperature does not exceed 125°C. If the junction temperature increases above that, an internal Thermal Shutdown circuit activates at 170°C (typical) to disable the VCC regulator and the gate driver, and discharge the soft-start capacitor. This feature helps prevent catastrophic failures from accidental device overheating. When the junction temperature falls below 150°C (typical hysteresis = 20°C), the gate driver is enabled, the soft-start circuit is released, and normal operation resumes. Applications Information EXTERNAL COMPONENTS The procedure for calculating the external components is illustrated with the following design example. Referring to Block Diagram, the circuit is to be configured for the following specifications: • VOUT = 5V • VIN = 7V to 42V, 12V Nominal • Maximum load current (IOUT(max)) = 5A • Minimum load current (IOUT(min)) = 600mA (for continuous conduction mode) • Switching Frequency (FSW) = 300kHz • Maximum allowable output ripple (VOS) = 5mVp-p • Selected PFET: Vishay Si7465 • RFB1 and RFB2: These resistors set the output voltage. The ratio of these resistors is calculated from: RFB2/RFB1 = (VOUT/1.25V) - 1 For this example, RFB2 / RFB1 = 3. Typically, RFB1 and RFB2 should be chosen from standard value resistors in the range of 1kΩ to 20kΩ which satisfy the above ratio. For this example, RFB2 = 10kΩ, and RFB1 = 3.4kΩ. 14 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com • RT, PFET: Before selecting the RT resistor, the PFET must be selected as its turn-on and turn-off delays affect the calculated value of RT. For the Vishay Si7465 PFET, the difference of its typical turn-off and turn-on delays is 57ns. Using Equation 5 at nominal input voltage, RT calculates to be: RT = • SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 5 x (12 - 1.56V) -7 1.45 x 10 x 12 x 300 kHz - (50 ns + 57 ns) x (12 - 1.56V) 1.45 x 10 -7 - 1.4 = 90.9 A standard value 90.9kΩ resistor is selected. Using Equation 3 the minimum on-time at the PGATE pin, which occurs at maximum input voltage (42V), is calculated to be 381ns. This minimum one-shot period is sufficiently longer than the minimum recommended value of 150ns. The minimum on-time at the SW node is longer due to the delay added by the PFET (57ns). Therefore the minimum SW node on-time is 438ns at 42V. At the SW node the maximum on-time is calculated to be 2.55µs at 7V. L1: The main parameter controlled by the inductor value is the current ripple amplitude (IOR). See Figure 27. The minimum load current for continuous conduction mode is used to determine the maximum allowable ripple such that the inductor current’s lower peak does not fall below 0mA. Continuous conduction mode operation at minimum load current is not a requirement of the LM25085, but serves as a guideline for selecting L1. For this example, the maximum ripple current is: IOR(max) = 2 x IOUT(min) = 1.2 Amp (13) If an application’s minimum load current is zero, a good initial estimate for the maximum ripple current (IOR(max)) is 20% of the maximum load current. The ripple calculated in Equation 13 is then used in the following equation to calculate L1: tON(min) x (VIN(max) - VOUT) L1 = = 13.5 PH IOR(max) (14) Inductor Current A standard value 15µH inductor is selected. Using this inductance value, the maximum ripple current amplitude, which occurs at maximum input voltage, calculates to 1.08Ap-p. The peak current (IPK) at maximum load current is 5.54A. However, the current rating of the selected inductor must be based on the maximum current limit value calculated below. IPK IOR IOUT SW Node 1/FS Figure 27. Inductor Current Waveform • RSEN, RADJ: To achieve good current limit accuracy and avoid over designing the power stage components, the sense resistor method is used for current limiting in this example. A standard value 10mΩ resistor is selected for RSEN, resulting in a 50mV drop at maximum load current, and a maximum 0.25W power dissipation in the resistor. Since the LM25085 uses peak current detection, the minimum value for the current limit threshold must be equal to the maximum load current (5A) plus half the maximum ripple amplitude calculated above: ICL(min) = 5A + 1.08A/2 = 5.54A At this current level the voltage across RSEN is 55.4mV. Adding the current limit comparator offset of 9mV (max) increases the required current limit threshold to 6.44A. Using Equation 7 with the minimum value for the ADJ pin current (32µA), the required RADJ resistor calculates to: RADJ = 6.44A x 0.01: = 2.01 k: 32 PA A standard value 2.1kΩ resistor is selected. The nominal current limit threshold calculates to: ICL(nom) = (2.1 k: x 40 PA) 0.01: = 8.4A Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 15 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com Using the tolerances for the ADJ pin current and the current limit comparator offset, the maximum current limit threshold calculates to: (2.1 k: x 48 PA) + 9 mV ICL(max) = 0.01: = 11A The minimum current limit thresholds calculate to: ICL(min) = • (2.1 k: x 32 PA) - 9 mV 0.01: = 5.82A The load current in each case is equal to the current limit threshold minus half the current ripple amplitude. The recommended value of 1000pF for CADJ is used in this example. COUT: Since the maximum allowed output ripple voltage is very low in this example (5mVp-p), the minimum ripple configuration (R3, C1, and C2 in the Block Diagram) must be used. The resulting ripple at VOUT is then due to the inductor’s ripple current passing through COUT. This capacitor’s value can be selected based on the maximum allowable ripple voltage at VOUT, or based on transient response requirements. The following calculation, based on ripple voltage, provides a first order result for the value of COUT: IOR(max) COUT = 8 x FS x VRIPPLE where IOR(max) is the maximum ripple current calculated above, and VRIPPLE is the allowable ripple at VOUT. COUT = • 1.08A = 90 PF 8 x 300 kHz x 0.005V R3, C1, C2: The minimum ripple configuration uses these three components to generate the ripple voltage required at the FB pin since there is insufficient ripple at VOUT. A minimum of 25mVp-p must be applied to the FB pin to obtain stable constant frequency operation. R3 and C1 are selected to generate a sawtooth waveform at their junction, and that waveform is AC coupled to the FB pin via C2. The values of the three components are determined using the following procedure: A 100µF capacitor is selected. Typically the ripple amplitude will be higher than the calculations indicate due to the capacitor’s ESR. Calculate VA = VOUT - (VSW x (1 – (VOUT/VIN(min)))) where VSW is the absolute value of the voltage at the SW node during the off-time, typically 0.5V to 1V depending on the diode D1. Using a typical value of 0.65V, VA calculates to 4.81V. VA is the nominal DC voltage at the R3/C1 junction, and is used in the next equation: (VIN(min) - VA) x tON R3 x C1 = 'V where tON is the maximum on-time (at minimum input voltage, and ΔV is the desired ripple amplitude at the R3/C1 junction, typically 25mVp-p. R3 x C1 = • (7V - 4.81V) x 2.55 Ps -4 = 2.23 x 10 0.025V R3 and C1 are then selected from standard value components to produce the product calculated above. Typical values for C1 are 3000pF to 10,000pF, and R3 is typically from 10kΩ to 300kΩ. C2 is then chosen large compared to C1, typically 0.1µF. For this example, 3300pF is chosen for C1, requiring R3 to be 67.7kΩ. A standard value 66.5kΩ resistor is selected. CIN, CBYP: These capacitors limit the voltage ripple at VIN by supplying most of the switch current during the on-time. At maximum load current, when Q1 is switched on, the current through Q1 suddenly increases to the lower peak of the inductor’s ripple current, then ramps up to the upper peak, and then drops to zero at turnoff. The average current during the on-time is the load current. For a worst case calculation, these capacitors must supply this average load current during the maximum on-time, while limiting the voltage drop at VIN. For this example, 0.5V is selected as the maximum allowable droop at VIN. Their minimum value is calculated from: CIN + CBYP = 16 IOUT(max) x tON(max) 'V = 5A x 2.55 Ps = 25.5 PF 0.5V Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com • • • SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 A 33µF electrolytic capacitor is selected for CIN, and a 1µF ceramic capacitor is selected for CBYP. Due to the ESR of CIN, the ripple at VIN will likely be higher than the calculation indicates, and therefore it may be desirable to increase CIN to 47µF or 68µF. CBYP must be located as close as possible to the VIN and GND pins of the LM25085. The voltage rating for both capacitors must be at least 42V. The RMS ripple current rating for the input capacitors must also be considered. A good approximation for the required ripple current rating is IRMS > IOUT/2. D1: A Schottky diode is recommended. Ultra-fast recovery diodes are not recommended as the high speed transitions at the SW pin may affect the regulator’s operation due to the diode’s reverse recovery transients. The diode must be rated for the maximum input voltage, and the worst case current limit level. The average power dissipation in the diode is calculated from: PD1 = VF x IOUT x (1-D) where VF is the diode’s forward voltage drop, and D is the on-time duty cycle. Using Equation 1, the minimum duty cycle occurs at maximum input voltage, and is calculated to be ≊11.9% in this example. The diode power dissipation calculates to be: PD1 = 0.65V x 5A x (1- 0.119) = 2.86W CVCC: The capacitor at the VCC pin (from VIN to VCC) provides not only noise filtering and stability for the VCC regulator, but also provides the surge current for the PFET gate drive. The typical recommended value for CVCC is 0.47µF. A good quality, low ESR, ceramic capacitor is recommended. CVCC must be located as close as possible to the VIN and VCC pins. If the selected PFET has a Total Gate Charge specification of 100nC or larger, or if the circuit is required to operate at input voltages below 7V, a larger capacitor may be required. The maximum recommended value for CVCC is 1µF. IC Power Dissipation: The maximum power dissipated in the LM25085 package is calculated using Equation 12 at the maximum input voltage. The Total Gate Charge for the Si7465 PFET is specified to be 40nC (max) in its data sheet. Therefore the total power dissipation within the LM25085 is calculated to be: PDISS = 42V x ((40nC x 300kHz) + 1.3mA) = 559mW Using an HVSSOP-PowerPAD-8 package with a θJA of 46°C/W produces a temperature rise of 26°C from junction to ambient. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 17 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com Final Design Example Circuit The final circuit is shown in Figure 28, and its performance is presented in Figure 29 through Figure 32. CVCC 7V to 42V Input LM25085 VIN VIN CIN 33 PF GND 0.47 PF VCC CBYP 1 PF CADJ 1000 pF ADJ RT 90.9 k: RADJ RSEN 2.1 k: 0.01: ISEN RT SHUTDOWN L1 15 PH PGATE VOUT Q1 D1 GND R3 66.5 k: C2 0.1 PF C1 3300 pF RFB2 10 k: 5V COUT 100 PF GND RFB1 FB 3.4 k: Figure 28. Example Circuit Figure 29. Efficiency vs. Load Current and VIN (Circuit of Figure 28) 18 Submit Documentation Feedback Figure 30. Frequency vs. VIN (Circuit of Figure 28) Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 Figure 31. Current Limit vs. VIN (Circuit of Figure 28) Figure 32. LM25085 Power Dissipation (Circuit of Figure 28) Alternate Output Ripple Configurations The minimum ripple configuration, using C1, C2 and R3, used in the example circuit, Figure 28, results in a low ripple amplitude at VOUT determined mainly by the characteristics of the output capacitor and the ripple current in L1. This configuration allows multiple ceramic capacitors to be used for VOUT if the output voltage is provided to several places on the PC board. However, if a slightly higher level of ripple at VOUT is acceptable in the application, and distributed capacitance is not used, the ripple required for the FB comparator pin can be generated with fewer external components using the circuits shown below. Reduced ripple configuration: In Figure 33, R3, C1 and C2 are removed (compared to Figure 28). A low value resistor (R4) is added in series with COUT, and a capacitor (Cff) is added across RFB2. Ripple is generated at VOUT by the inductor’s ripple current flowing through R4, and that ripple voltage is passed to the FB pin via Cff. The ripple at VOUT can be set as low as 25mVp-p since it is not attenuated by RFB2 and RFB1. The minimum value for R4 is calculated from: R4 = 25 mV IOR(min) where IOR(min) is the minimum ripple current, which occurs at minimum input voltage. The minimum value for Cff is determined from: 3 x tON(max) Cff = (RFB1//RFB2) where tON(max) is the maximum on-time, which occurs at minimum VIN. The next larger standard value capacitor should be used for Cff. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 19 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com LM25085 L1 PGATE VOUT Q1 D1 Cff RFB2 R4 FB COUT GND RFB1 GND Figure 33. Reduced Ripple Configuration Lowest cost configuration: This configuration, shown in Figure 34, is the same as Figure 33 except Cff is removed. Since the ripple voltage at VOUT is attenuated by RFB2 and RFB1, the minimum ripple required at VOUT is equal to: VRIP(min) = 25mV x (RFB2 + RFB1)/RFB1 The minimum value for R4 is calculated from: R4 = VRIP(min) IOR(min) where IOR(min) is the minimum ripple current, which occurs at minimum input voltage. LM25085 L1 PGATE Q1 D1 VOUT RFB2 FB R4 COUT GND RFB1 GND Figure 34. Lowest Cost Ripple Generating Configuration PC Board Layout In most applications, the heat sink pad or tab of Q1 is connected to the switch node, i.e. the junction of Q1, L1 and D1. While it is common to extend the PC board pad from under these devices to aid in heat dissipation, the pad size should be limited to minimize EMI radiation from this switching node. If the PC board layout allows, a similarly sized copper pad can be placed on the underside of the PC board, and connected with as many vias as possible to aid in heat dissipation. 20 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 LM25085, LM25085-Q1 www.ti.com SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 The voltage regulation, over-voltage, and current limit comparators are very fast and can respond to short duration noise pulses. Layout considerations are therefore critical for optimum performance. The layout must be as neat and compact as possible with all the components as close as possible to their associated pins. Two major current loops conduct currents which switch very fast, requiring the loops to be as small as possible to minimize conducted and radiated EMI. The first loop is that formed by CIN, Q1, L1, COUT, and back to CIN. The second loop is that formed by D1, L1, COUT, and back to D1. The connection from the anode of D1 to the ground end of CIN must be short and direct. CIN must be as close as possible to the VIN and GND pins, and CVCC must be as close as possible to the VIN and VCC pins. If the anticipated internal power dissipation of the LM25085 will produce excessive junction temperatures during normal operation, a package option with an exposed pad must be used (HVSSOP-PowerPAD-8 or WSON-8). Effective use of the PC board ground plane can help dissipate heat. Additionally, the use of wide PC board traces, where possible, helps conduct heat away from the IC. Judicious positioning of the PC board within the end product, along with the use of any available air flow (forced or natural convection) also helps reduce the junction temperature. Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 Submit Documentation Feedback 21 LM25085, LM25085-Q1 SNVS593H – OCTOBER 2008 – REVISED MARCH 2013 www.ti.com REVISION HISTORY Changes from Revision G (March 2013) to Revision H • 22 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 21 Submit Documentation Feedback Copyright © 2008–2013, Texas Instruments Incorporated Product Folder Links: LM25085 LM25085-Q1 PACKAGE OPTION ADDENDUM www.ti.com 19-Jul-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) LM25085MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVZB LM25085MME/NOPB ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVZB LM25085MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVZB LM25085MY/NOPB ACTIVE MSOPPowerPAD DGN 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVYB LM25085MYE/NOPB ACTIVE MSOPPowerPAD DGN 8 250 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVYB LM25085MYX/NOPB ACTIVE MSOPPowerPAD DGN 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SVYB LM25085QMY/NOPB ACTIVE MSOPPowerPAD DGN 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SYLB LM25085QMYE/NOPB ACTIVE MSOPPowerPAD DGN 8 250 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SYLB LM25085QMYX/NOPB ACTIVE MSOPPowerPAD DGN 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 SYLB LM25085SD/NOPB ACTIVE WSON NGQ 8 1000 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM -40 to 125 L246B LM25085SDE/NOPB ACTIVE WSON NGQ 8 250 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM -40 to 125 L246B LM25085SDX/NOPB ACTIVE WSON NGQ 8 4500 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM -40 to 125 L246B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 19-Jul-2013 Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LM25085, LM25085-Q1 : • Catalog: LM25085 • Automotive: LM25085-Q1 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing LM25085MM/NOPB VSSOP DGK 8 LM25085MME/NOPB VSSOP DGK LM25085MMX/NOPB VSSOP DGK LM25085MY/NOPB MSOPPower PAD LM25085MYE/NOPB SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 8 250 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 DGN 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 MSOPPower PAD DGN 8 250 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM25085MYX/NOPB MSOPPower PAD DGN 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM25085QMY/NOPB MSOPPower PAD DGN 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM25085QMYE/NOPB MSOPPower PAD DGN 8 250 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM25085QMYX/NOPB MSOPPower PAD DGN 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM25085SD/NOPB WSON NGQ 8 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Oct-2013 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM25085SDE/NOPB WSON NGQ 8 250 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 LM25085SDX/NOPB WSON NGQ 8 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM25085MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LM25085MME/NOPB VSSOP DGK 8 250 210.0 185.0 35.0 LM25085MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 LM25085MY/NOPB MSOP-PowerPAD DGN 8 1000 210.0 185.0 35.0 LM25085MYE/NOPB MSOP-PowerPAD DGN 8 250 210.0 185.0 35.0 LM25085MYX/NOPB MSOP-PowerPAD DGN 8 3500 367.0 367.0 35.0 LM25085QMY/NOPB MSOP-PowerPAD DGN 8 1000 210.0 185.0 35.0 LM25085QMYE/NOPB MSOP-PowerPAD DGN 8 250 210.0 185.0 35.0 LM25085QMYX/NOPB MSOP-PowerPAD DGN 8 3500 367.0 367.0 35.0 LM25085SD/NOPB WSON NGQ 8 1000 210.0 185.0 35.0 LM25085SDE/NOPB WSON NGQ 8 250 210.0 185.0 35.0 LM25085SDX/NOPB WSON NGQ 8 4500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA DGN0008A MUY08A (Rev A) BOTTOM VIEW www.ti.com MECHANICAL DATA NGQ0008A SDA08A (Rev A) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated