Foryard FYLS-3528PGC Smd Datasheet

SMD
FYLS – 3528PGC
Features:
z
z
z
z
Single color
Suitable for all SMT assembly and solder process.
Available on tape and Reel.
Package : 2000pcs/ Reel.
Description.
z
z
z
The green source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide pure green
Light Emitting Diode.
It is recommended to use a wrist band or anti-electrostatic glove when handling the LEDs.
All devices equipment and machinery must be electrically grounded.
Package Dimensions
2
1
2
Polarity mark
C0.8
Notes:
1. All dimension units are millimeters(Inches)
2. All dimension tolerance ±0.2mm unless otherwise noted.
3. An epoxy meniscus may extend about 1.5mm down the leads.
1
SMD
Selection Guide
Part No.
FYLS-3528PGC
Dice
IV(mcd)@20mA
lens type
Green(InGaN)
Viewing
Angle
Min
Typ
2θ1/2
---
1500
120
Water clear
Electrical/Optical Characteristics at Ta=25 ゜с
Symbol
λd
Parameter
Dominate
wavelength
Device
min.
typ.
units
test conditions
Green
515
520
nm
IF=20mA
3.0
3.2
V
IF=20mA
VF
Forward Voltage
IR
Reverse Current
5
µA
VR=5V
C
capactiance
100
PF
VF=0V,f=1MHZ
Absolute Maximum Ratings At= 25 ゜с
Parameter
White
Units
Power dissipation
120
mW
DC Forward Current
30
mA
Peak Forward Current(1)
100
mA
Reverse Voltage
5
V
Operating/storage Temperature
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
-40℃ to +85℃
SMD
Typical Electrical/Optical Characteristics Curves(Ta=25℃ Unless Otherwise
Noted)
Normalized Response
(1)
(1)peak@520nm/pure green
Wave Length(nm)
Relative Luminous intensity
vs Forward current
Forward Current Derating Curve
Relative Intensity
(Lop@20mA=1)
Forward Current(mA)
60
50
40
30
20
10
0
0
10
20
30
40
50
60
Ambient Temperature TA (
70
80
90
Forward Current IF(mA)
)
luminous Intensity Vs.Ambient Temperature °C
luminous Intensity (IV)
Forward Current If(mA)
Forward Current vs.Forward Voltage
Forward Voltage VF( V)
-20
0
20
40
Ambient Temperature C
60
80
SMD
Precautions for use:
1. Suggest the LEDs should be kept between 5℃ and 30℃and 60%RH or less before
opening the package, The max. storage period before opening the package is 1 year.
2. After opening the package, the LEDs should be kept at 30℃/35%RH or less, and it
should be used within 1 hours. In the event of incomplete usage, it is advised that user
preheat the remaining devices at 60±5℃ for 12 hours prior to use.
3. The temperature of manual of soldering not more then 300℃ within 2 sec. The
temperature of Reflow soldering not more then 260℃ within 2 sec, should not be done
more than twice. When soldering, don’t tress on LEDs during heating. After soldering,
don’t warp the circuit board.
4. Repair should not be done after the LEDs have been soldered. When repair is
unavoidable, double-head soldering iron should be used. It should be confirmed
beforehand whether the characteristics of the LEDs will be damaged by repair or not.
(1)
Reflow soldering
Temperature profile
Temperature
Peak temperature
Melting-point
Pre-heat
Soak
Reflow
Cooling
Time
Solder=Sn63-Pb37
Solder= Pb-Free
Average ramp-up rate:4℃/sec.max
Peak preheat temperature:100-150℃
Average ramp-up rate:4℃/sec.max
Peak preheat temperature:100-150℃
preheat time:100seconds.max
ramp-down rate:6℃/sec.max
Peak temperature:230℃
Time within 5℃ of actual peak
temperature=10 sec. max
Duration above 183℃ is 80 sec. max
preheat time:100seconds.max
ramp-down rate:6℃/sec.max
Peak temperature:250℃
Time within 5℃ of actual peak temperature=10
sec. max
Duration above 217℃ is 80 sec. max
SMD
Recommended Soldering Pattern(Unit:mm)
Taping Dimension (Unit:mm)
Reel end of Tape no LED
Reel Leed Min. 200mm
LED mounting part
NO LED
Reel Leed Min. 200mm
SMD
‹ Packing and Shipping Spec.
L1
sb
W1
sb
Zip-lock
Desiccant
Antistatic
Bag
Spec.
Spec.
Spec.
203.0.
198.0
Unit:mm
)
s
c
p
(
Y
T
'
Q
Box Dimension(cm):30 * 19* 11.5
Desiccant
.
O
N
T
R
A
P
10 Reels per box
CARTON
Dimension(cm):39*32*38
6boxs/carton
0603B/0603/0805:
4000pcs*10Reels*6boxs
S
G
K S
G
K M
C
8
3
*
1
3
*
8
3
W
W :
S
.
G .
N A
E
M
C/NO
0805B/1206B/1206 1210/1204:
3000pcs*10Reels*6boxs*
3528:2000pcs*10Reels*6boxs
5050:1000pcs*8Reels*6boxs
Similar pages