Exar CLC4011ISO14MTR Low power, low cost, rail-to-rail i/o amplifier Datasheet

CLC2011, CLC4011
Low Power, Low Cost, Rail-to-Rail I/O Amplifiers
FE ATU R E S
■■ 136μA supply current
■■ 4.9MHz bandwidth
■■ Output swings to within 20mV of either rail
■■ Input voltage range exceeds the rail by
>250mV
■■ 5.3V/μs slew rate
■■ 21nV/√Hz input voltage noise
■■ ±35mA linear output current
■■ Fully specified at 2.7V and 5V supplies
General Description
The CLC2011 (dual) and CLC4011 (quad) are ultra-low cost, low power,
voltage feedback amplifiers. At 2.7V, the CLCx011 family uses only 136μA
of supply current per amplifier and are designed to operate from a supply
range of 2.5V to 5.5V (±1.25 to ±2.75). The input voltage range exceeds the
negative and positive rails.
The CLCx011 family of amplifiers offer high bipolar performance at a low
CMOS prices. They offer superior dynamic performance with 4.9MHz small
signal bandwidths and 5.3V/μs slew rates. The combination of low power,
high bandwidth, and rail-to-rail performance make the CLCx011 amplifiers
well suited for battery-powered communication/computing systems.
A P P LICATION S
■■ Portable/battery-powered applications
■■ Mobile communications, cell phones,
pagers
■■ ADC buffer
■■ Active filters
■■ Portable test instruments
■■ Notebooks and PDA’s
■■ Signal conditioning
■■ Medical equipment
■■ Portable medical instrumentation
Ordering Information - back page
Output Swing vs. Load
Large Signal Frequency Response
1.35
Output Voltage (0.27V/div)
V s = 5V
Magnitude (1dB/div)
V o = 1Vpp
V o = 4Vpp
V o = 2Vpp
R L = 10kΩ
R L = 1kΩ
0
R L = 75Ω
R L = 100Ω
R L = 200Ω
R L = 75/100Ω
-1.35
0.01
0.1
1
-2.0
10
Frequency (MHz)
© 2009 - 2014 Exar Corporation 0
2.0
Input Voltage (0.4V/div)
1 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Absolute Maximum Ratings
Operating Conditions
Stresses beyond the limits listed below may cause
permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect
device reliability and lifetime.
Supply Voltage Range....................................................2.5 to 5.5V
Operating Temperature Range................................-40°C to 125°C
Junction Temperature............................................................ 150°C
Storage Temperature Range....................................-65°C to 150°C
Lead Temperature (Soldering, 10s).......................................260°C
VS...................................................................................... 0V to 6V
VIN............................................................. -VS - 0.5V to +VS +0.5V
Package Thermal Resistance
Continuous Output Current...................................-40mA to +40mA
θJA (SOIC-8)......................................................................150°C/W
θJA (MSOP-8)................................................................... 200°C/W
θJA (SOIC-14)..................................................................... 90°C/W
θJA (TSSOP-14).................................................................100°C/W
Package thermal resistance (θJA), JEDEC standard, multi-layer
test boards, still air.
ESD Protection
CLC2011, CLC4011 (HBM)........................................................2kV
ESD Rating for HBM (Human Body Model).
© 2009 - 2014 Exar Corporation 2 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Electrical Characteristics at +2.7V
TA = 25°C, VS = +2.7V, Rf = Rg = 5kΩ, RL = 10kΩ to VS/2; G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
UGBWSS
Unity Gain -3dB Bandwidth
G = +1, VOUT = 0.02Vpp
4.9
MHz
BWSS
-3dB Bandwidth
G = +2, VOUT = 0.2Vpp
3.2
MHz
BWLS
Large Signal Bandwidth
G = +2, VOUT = 2Vpp
1.4
MHz
GBWP
Gain Bandwidth Product
G = +11, VOUT = 0.2Vpp
2.5
MHz
Time Domain Response
tR, tF
Rise and Fall Time
VOUT = 1V step; (10% to 90%)
163
ns
tS
Settling Time to 0.1%
VOUT = 1V step
500
ns
OS
Overshoot
VOUT = 1V step
<1
%
SR
Slew Rate
1V step
5.3
V/μs
Distortion/Noise Response
HD2
2nd Harmonic Distortion
10kHz, VOUT = 1Vpp
-72
dBc
HD3
3rd Harmonic Distortion
10kHz, VOUT = 1Vpp
-72
dBc
THD
Total Harmonic Distortion
10kHz, VOUT = 1Vpp
0.03
%
en
Input Voltage Noise
>10kHz
21
nV/√Hz
XTALK
Crosstalk
Channel to Channel, VOUT = 2Vpp, f = 10kHz
82
dB
Channel to Channel, VOUT = 2Vpp, f = 50kHz
74
dB
0.5
mV
μV/°C
DC Performance
VIO
Input Offset Voltage
dVIO
Average Drift
5
IB
Input Bias Current
90
nA
dIB
Average Drift
32
pA/°C
PSRR
Power Supply Rejection Ratio
DC
83
dB
AOL
Open Loop Gain
VOUT = VS / 2
90
dB
IS
Supply Current
per channel
136
μA
Non-inverting
12
MΩ
2
pF
-0.25 to
2.95
V
81
dB
RL = 10kΩ to VS / 2
0.02 to
2.68
V
RL = 1kΩ to VS / 2
0.05 to
2.63
V
RL = 200Ω to VS / 2
0.11 to
2.52
V
±30
mA
55
Input Characteristics
RIN
Input Resistance
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio
DC
Output Characteristics
VOUT
IOUT
Output Voltage Swing
Output Current
© 2009 - 2014 Exar Corporation 3 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Electrical Characteristics at +5V
TA = 25°C, VS = +5V, Rf = Rg = 5kΩ, RL = 10kΩ to VS/2; G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
UGBWSS
Unity Gain -3dB Bandwidth
G = +1, VOUT = 0.02Vpp
4.3
MHz
BWSS
-3dB Bandwidth
G = +2, VOUT = 0.2Vpp
3.0
MHz
BWLS
Large Signal Bandwidth
G = +2, VOUT = 2Vpp
2.3
MHz
GBWP
Gain Bandwidth Product
G = +11, VOUT = 0.2Vpp
2.5
MHz
Time Domain Response
tR, tF
Rise and Fall Time
VOUT = 1V step; (10% to 90%)
110
ns
tS
Settling Time to 0.1%
VOUT = 2V step
470
ns
OS
Overshoot
VOUT = 1V step
<1
%
SR
Slew Rate
2V step
9
V/μs
Distortion/Noise Response
HD2
2nd Harmonic Distortion
10kHz, VOUT = 1Vpp
-73
dBc
HD3
3rd Harmonic Distortion
10kHz, VOUT = 1Vpp
-75
dBc
THD
Total Harmonic Distortion
10kHz, VOUT = 1Vpp
0.03
%
en
Input Voltage Noise
>10kHz
22
nV/√Hz
XTALK
Crosstalk
Channel to Channel, VOUT = 2Vpp, f = 10kHz
82
dB
Channel to Channel, VOUT = 2Vpp, f = 50kHz
74
dB
DC Performance
VIO
Input Offset Voltage
-8
dVIO
Average Drift
15
IB
Input Bias Current
90
dIB
Average Drift
40
pA/°C
PSRR
Power Supply Rejection Ratio
DC
85
dB
AOL
Open Loop Gain
VOUT = VS / 2
80
IS
Supply Current
per channel
160
Non-inverting
12
MΩ
2
pF
-0.25 to
5.25
V
58
80
dB
0.08 to
4.92
0.04 to
4.96
V
RL = 1kΩ to VS / 2
0.07 to
4.9
V
RL = 200Ω to VS / 2
0.14 to
4.67
V
±35
mA
55
1.5
8
mV
μV/°C
450
nA
dB
235
μA
Input Characteristics
RIN
Input Resistance
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio
DC
Output Characteristics
RL = 10kΩ to VS / 2
VOUT
IOUT
Output Voltage Swing
Output Current
© 2009 - 2014 Exar Corporation 4 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
CLC2011 Pin Configurations
CLC2011 Pin Assignments
SOIC-8 / MSOP-8
SOIC-8 / MSOP-8
OUT1
1
-IN1
2
+IN1
3
-Vs
+
4
+
Pin No.
Pin Name
Description
1
OUT1
8
+Vs
2
-IN1
Negative input, channel 1
7
OUT2
3
+IN1
Positive input, channel 1
4
-VS
6
-IN2
5
+IN2
Positive input, channel 2
+IN2
6
-IN2
Negative input, channel 2
7
OUT2
8
+VS
5
Output, channel 1
Negative supply
Output, channel 2
Positive supply
CLC4011 Pin Configuration
CLC4011 Pin Assignments
SOIC-14 / TSSOP-14
SOIC-14 / TSSOP-14
OUT1
1
14
OUT4
-IN1
2
13
-IN4
+IN1
3
12
+IN4
+VS
4
11
-VS
+IN2
5
10
+IN3
-IN2
6
9
-IN3
OUT2
7
8
OUT3
© 2009 - 2014 Exar Corporation Pin No.
Pin Name
1
OUT1
Description
2
-IN1
Negative input, channel 1
3
+IN1
Positive input, channel 1
4
+VS
Positive supply
5
+IN2
Positive input, channel 2
6
-IN2
Negative input, channel 2
7
OUT2
Output, channel 2
8
OUT3
Output, channel 3
9
-IN3
Negative input, channel 3
10
+IN3
Positive input, channel 3
Output, channel 1
11
-VS
12
+IN4
Positive input, channel 4
13
-IN4
Negative input, channel 4
14
OUT4
5 / 17
Negative supply
Output, channel 4
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Typical Performance Characteristics
TA = 25°C, VS = +2.7V, Rf = Rg = 5kΩ, RL = 10kΩ to VS/2; G = 2; unless otherwise noted.
V o = 0.2Vpp
Inverting Frequency Response at VS = 5V
Normalized Magnitude (1dB/div)
Normalized Magnitude (1dB/div)
Non-Inverting Frequency Response at VS = 5V
G=1
Rf = 0
G=2
R f = 5kΩ
R f = 5kΩ
G=5
R f = 5kΩ
0.01
0.1
1
V o = 0.2Vpp
R f = 5kΩ
R f = 5kΩ
R f = 5kΩ
R f = 5kΩ
0.01
10
0.1
Frequency (MHz)
G=1
Rf = 0
G=2
R f = 5kΩ
R f = 5kΩ
G=5
R f = 5kΩ
0.01
0.1
1
R f = 5kΩ
G = -2
G = -5
0.01
10
CL
R s = 0Ω
+
Rs
5kΩ
CL
1
10
Frequency Response vs RL
Magnitude (1dB/div)
Magnitude (1dB/div)
CL
R s = 0Ω
CL
R s = 0Ω
-
0.1
Frequency (MHz)
Frequency Response vs CL
CL
R s = 100Ω
G = -1
G = -10
Frequency (MHz)
V o = 0.05V
10
Inverting Frequency Response at VS = 2.7V
Normalized Magnitude (1dB/div)
Normalized Magnitude (1dB/div)
Non-Inverting Frequency Response at VS = 2.7V
V o = 0.2Vpp
1
Frequency (MHz)
RL
RL = 1kΩ
RL = 10kΩ
RL = 200Ω
RL = 50Ω
5kΩ
0.01
0.1
1
10
0.01
© 2009 - 2014 Exar Corporation 0.1
1
10
Frequency (MHz)
Frequency (MHz)
6 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Typical Performance Characteristics
TA = 25°C, VS = +2.7V, Rf = Rg = 5kΩ, RL = 10kΩ to VS/2; G = 2; unless otherwise noted.
Frequency Response vs. VOUT
Open Loop Gain & Phase vs. Frequency
140
V s = 5V
Open Loop Gain (dB)
V o = 4Vpp
V o = 2Vpp
No load
100
80
60
0
40
-45
20
-90
0
R L = 10kΩ
-135
No load
-20
0.01
0.1
1
-180
10 0
10
Open Loop Phase (deg)
V o = 1Vpp
Magnitude (1dB/div)
V s = 5V
120 R L = 10kΩ
10 1
10 2
10 3
10 4
10 5
10 6
10 7
10 8
Frequency (Hz)
Frequency (MHz)
-20
-20
-30
-30
-40
-40
Distortion (dBc)
Distortion (dBc)
2nd Harmonic Distortion vs VOUT 3rd Harmonic Distortion vs VOUT
-50
50kHz
-60
100kHz
50kHz
-70
-50
100kHz
-60
20kHz
-70
10kHz
10kHz, 20kHz
-80
50kHz
-80
10kHz
-90
-90
0.5
1
1.5
2
0.5
2.5
Output Amplitude (Vpp)
2nd & 3rd Harmonic Distortion at VS = 2.7V
-20
-40
2
2.5
55
50
R L = 200Ω
R L = 1kΩ
-50
45
nV/√Hz
Distortion (dBc)
R L = 200Ω
1.5
Input Voltage Noise
V o = 1Vpp
-30
1
Output Amplitude (Vpp)
R L = 10kΩ
-60
-70
40
35
30
25
20
15
10
-80
R L = 10kΩ
-90
0
20
40
60
R L = 1kΩ
80
5
0
100
0.1k
Frequency (kHz)
© 2009 - 2014 Exar Corporation 1k
10k
100k
1M
Frequency (Hz)
7 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Typical Performance Characteristics
TA = 25°C, VS = +2.7V, Rf = Rg = 5kΩ, RL = 10kΩ to VS/2; G = 2; unless otherwise noted.
PSRR
0
0
-10
-10
-20
-20
-30
-30
PSRR (dB)
CMRR (dB)
CMRR
-40
-50
-60
-40
-50
-60
-70
-70
-80
-80
-90
-90
10
100
1000
10000
100000
10
Frequency (Hz)
100
1000
10000
100000
Frequency (Hz)
Output Swing vs. Load
Pulse Response vs. Common Mode Voltage
R L = 10kΩ
Output Voltage (0.5V/div)
Output Voltage (0.27V/div)
1.35
R L = 1kΩ
0
R L = 75Ω
R L = 100Ω
R L = 200Ω
R L = 75/100Ω
1.2V offset
0.6V offset
No offset
-0.6V offset
-1.2V offset
-1.35
-2.0
0
2.0
Time (1µs/div)
Input Voltage (0.4V/div)
Crosstalk vs. Frequency
© 2009 - 2014 Exar Corporation 8 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Application Information
+Vs
General Description
The CLCx011 family of amplifiers are single supply, general
purpose, voltage-feedback amplifiers. They are fabricated
on a complimentary bipolar process, feature a rail-to-rail
input and output, and are unity gain stable.
Input
6.8μF
0.1μF
+
Output
RL
0.1μF
Basic Operation
Figures 1, 2, and 3 illustrate typical circuit configurations for
non-inverting, inverting, and unity gain topologies for dual
supply applications. They show the recommended bypass
capacitor values and overall closed loop gain equations.
Figure 4 shows the typical non-inverting gain circuit for
single supply applications.
+Vs
Input
6.8μF
-Vs
Figure 3: Unity Gain Circuit
+Vs
6.8μF
6.8μF
+
In
0.1μF
+
+
0.1μF
Out
Output
-
-
RL
0.1μF
Rg
6.8μF
-Vs
G=1
Rf
Rf
Rg
G = 1 + (Rf/Rg)
Figure 4: Single Supply Non-Inverting Gain Circuit
Figure 1: Typical Non-Inverting Gain Circuit
+Vs
R1
Input
Rg
Power Dissipation
6.8μF
0.1μF
+
Output
RL
0.1μF
6.8μF
-Vs
Rf
G = - (Rf/Rg)
For optimum input offset
voltage set R1 = Rf || Rg
Figure 2: Typical Inverting Gain Circuit
© 2009 - 2014 Exar Corporation Power dissipation should not be a factor when operating
under the stated 10kΩ load condition. However, applications
with low impedance, DC coupled loads should be analyzed
to ensure that maximum allowed junction temperature is
not exceeded. Guidelines listed below can be used to verify
that the particular application will not cause the device to
operate beyond it’s intended operating range.
Maximum power levels are set by the absolute maximum
junction rating of 150°C. To calculate the junction
temperature, the package thermal resistance value ThetaJA
(θJA) is used along with the total die power dissipation.
TJunction = TAmbient + (θJA × PD)
Where TAmbient is the temperature of the working
environment.
9 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
In order to determine PD, the power dissipated in the load
needs to be subtracted from the total power delivered by the
supplies.
Maximum Power Dissipation (W)
2.5
PD = Psupply - Pload
Supply power is calculated by the standard power equation.
Psupply = Vsupply × IRMSsupply
Vsupply = VS+ - VS-
TSSOP-14
2
SOIC-14
1.5
SOIC-8
1
0.5
MSOP-8
Power delivered to a purely resistive load is:
0
-40
Pload = ((Vload)RMS2)/Rloadeff
-20
0
20
40
60
80
100
120
Ambient Temperature (°C)
Figure 5. Maximum Power Derating
The effective load resistor (Rloadeff) will need to include
the effect of the feedback network. For instance, Rloadeff in
Figure 3 would be calculated as:
RL || (Rf + Rg)
These measurements are basic and are relatively easy to
perform with standard lab equipment. For design purposes
however, prior knowledge of actual signal levels and load
impedance is needed to determine the dissipated power.
Here, PD can be found from
PD = PQuiescent + PDynamic - Pload
Input Common Mode Voltage
The common mode input range extends to 250mV below
ground and to 250mV above Vs, in single supply operation.
Exceeding these values will not cause phase reversal.
However, if the input voltage exceeds the rails by more
than 0.5V, the input ESD devices will begin to conduct. The
output will stay at the rail during this overdrive condition. If
the absolute maximum input voltage (700mV beyond either
rail) is exceeded, externally limit the input current to ±5mA
as shown in Figure 6.
10k
Input
Output
Quiescent power can be derived from the specified IS values
along with known supply voltage, Vsupply. Load power can
be calculated as above with the desired signal amplitudes
using:
-
Figure 6. Circuit for Input Current Protection
(Vload)RMS = Vpeak / √2
( Iload)RMS = ( Vload)RMS / Rloadeff
The dynamic power is focused primarily within the output
stage driving the load. This value can be calculated as:
PDynamic = (VS+ - Vload)RMS × ( Iload)RMS
Driving Capacitive Loads
Increased phase delay at the output due to capacitive loading
can cause ringing, peaking in the frequency response, and
possible unstable behavior. Use a series resistance, RS,
between the amplifier and the load to help improve stability
and settling performance. Refer to Figure 7.
Assuming the load is referenced in the middle of the power
rails or Vsupply/2.
Input
+
Rs
-
The CLC2011 is short circuit protected. However, this may
not guarantee that the maximum junction temperature
(+150°C) is not exceeded under all conditions. Figure 5
shows the maximum safe power dissipation in the package
vs. the ambient temperature for the packages available.
© 2009 - 2014 Exar Corporation +
Rf
Output
CL
RL
Rg
Figure 7. Addition of RS for Driving Capacitive Loads
10 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Table 1 provides the recommended RS for various capacitive
loads. The recommended RS values result in approximately
<1dB peaking in the frequency response. The Frequency
Response vs. CL plot, on page 6, illustrates the response
of the CLCx011.
Layout Considerations
General layout and supply bypassing play major roles in
high frequency performance. Exar has evaluation boards to
use as a guide for high frequency layout and as an aid in
device testing and characterization. Follow the steps below
as a basis for high frequency layout:
■■
CL (pF)
RS (Ω)
-3dB BW (MHz)
10pF
0
2.2
20pF
0
2.4
50pF
0
2.5
100pF
100
2
■■
Place the 6.8µF capacitor within 0.75 inches of the power pin
■■
Place the 0.1µF capacitor within 0.1 inches of the power pin
■■
■■
Table 1: Recommended RS vs. CL
For a given load capacitance, adjust RS to optimize the
tradeoff between settling time and bandwidth. In general,
reducing RS will increase bandwidth at the expense of
additional overshoot and ringing.
Remove the ground plane under and around the part,
especially near the input and output pins to reduce parasitic
capacitance
Minimize all trace lengths to reduce series inductances
Refer to the evaluation board layouts below for more
information.
Evaluation Board Information
The following evaluation boards are available to aid in the
testing and layout of these devices:
Overdrive Recovery
An overdrive condition is defined as the point when either
one of the inputs or the output exceed their specified
voltage range. Overdrive recovery is the time needed for the
amplifier to return to its normal or linear operating point. The
recovery time varies, based on whether the input or output
is overdriven and by how much the range is exceeded.
The CLCx011 will typically recover in less than 50ns from
an overdrive condition. Figure 8 shows the CLC2011 in an
overdriven condition.
Include 6.8µF and 0.1µF ceramic capacitors for power supply
decoupling
Evaluation Board #
Products
CEB006
CLC2011 in SOIC
CEB010
CLC2011 in MSOP
CEB019
CLC4011 in TSSOP
CEB018
CLC4011 in SOIC
Evaluation Board Schematics
Evaluation board schematics and layouts are shown in
Figures 9-16 These evaluation boards are built for dualsupply operation. Follow these steps to use the board in a
single-supply application:
1. Short -VS to ground.
2. Use C3 and C4, if the -VS pin of the amplifier is not
directly connected to the ground plane.
Figure 8: Overdrive Recovery
© 2009 - 2014 Exar Corporation 11 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Figure 11. CEB006 Bottom View
Figure 9. CEB006 & CEB010 Schematic
Figure 12. CEB010 Top View
Figure 10. CEB006 Top View
Figure 13. CEB010 Bottom View
© 2009 - 2014 Exar Corporation 12 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Figure 16. CEB018 Bottom View
Figure 14. CEB018 Schematic
Figure 15. CEB018 Top View
© 2009 - 2014 Exar Corporation 13 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Mechanical Dimensions
MSOP-8
© 2009 - 2014 Exar Corporation 14 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Mechanical Dimensions
SOIC-8 Package
SOIC-14 Package
ECN 1344-13 11/01/2013
© 2009 - 2014 Exar Corporation 15 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
TSSOP-14 Package
ECN 1347-07 11/19/2013
© 2009 - 2014 Exar Corporation 16 / 17
exar.com/CLC2011
Rev 1D
CLC2011, CLC4011
Ordering Information
Part Number
Package
Green
Operating Temperature Range
Packaging
CLC2011ISO8X
SOIC-8
Yes
-40°C to +125°C
Tape & Reel
CLC2011ISO8MTR
SOIC-8
Yes
-40°C to +125°C
Mini Tape & Reel
CLC2011ISO8EVB
Evaluation Board
N/A
N/A
N/A
CLC2011IMP8X
MSOP-8
Yes
-40°C to +125°C
Tape & Reel
CLC2011IMP8MTR
MSOP-8
Yes
-40°C to +125°C
Mini Tape & Reel
CLC2011IMP8EVB
Evaluation Board
N/A
N/A
N/A
CLC4011ISO14X
SOIC-14
Yes
-40°C to +125°C
Tape & Reel
CLC4011ISO14MTR
SOIC-14
Yes
-40°C to +125°C
Mini Tape & Reel
CLC4011ISO14EVB
Evaluation Board
N/A
N/A
N/A
CLC4011ITP14X
TSSOP-14
Yes
-40°C to +125°C
Tape & Reel
CLC4011ITP14MTR
TSSOP-14
Yes
-40°C to +125°C
Mini Tape & Reel
CLC4011ITP14EVB
Evaluation Board
N/A
N/A
N/A
CLC2011 Ordering Information
CLC4011 Ordering Information
Moisture sensitivity level for all parts is MSL-1. Mini tape and reel quantity is 250.
Revision History
Revision
1D (ECN 1504-01)
Date
January 19,
2015
Description
Reformat into Exar data sheet template. Updated PODs and thermal resistance numbers. Updated
ordering information table to include MTR and EVB part numbers. Increased operating temperature to
+125°C.
For Further Assistance:
Email: [email protected] or [email protected]
Exar Technical Documentation: http://www.exar.com/techdoc/
Exar Corporation Headquarters and Sales Offices
48760 Kato Road
Tel.: +1 (510) 668-7000
Fremont, CA 94538 - USA
Fax: +1 (510) 668-7001
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation
assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free
of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user’s specific application. While the information
in this publication has been carefully checked; no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected
to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation
receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR
Corporation is adequately protected under the circumstances.
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
© 2009 - 2014 Exar Corporation 17 / 17
exar.com/CLC2011
Rev 1D
Similar pages