POWER ADN-C Series 120 - 960 Watts Data Sheet Total Power: 120-960 Watts Input Voltage: 85-264 Vac, 90-375 Vdc # of Outputs: Single SPECIAL FEATURES Slim form factor Five year warranty High efficiency > 90% Typ. Full power at 60 °C Power Boost™ Industrial grade design • Metal mounting clip • Metal case MTBF > 450,000h demonstrated at 40 °C Active PFC > 0.92 Adjustable output Overvoltage protection with autorecovery Continuous short circuit and overload protection SEMI F47 Sag Immunity New visual diagnostic LED Three Status LEDs • Input • Output • Alarm DC OK relay Parallel operation capability Screw terminal connections RoHS compliant No tools required for mounting SAFETY UL508, cULus Listed UL 60950-1, cURus IEC60950-1 Class I, Div 2 Hazardous Locations ATEX Certified on selected models IP20 CE Electrical Specifications Input AC input range Nominal: 100-240 Vac/115-230 Vac/85-264 Vac DC input range 90-375 Vdc Frequency 47-67 Hz, 400 Hz Efficiency > 90% Inrush current (typical) < 15A or < 60A depending on model PFC Active, better than 0.92 Output Nominal voltage 24 Vdc (22.5-28.5 Vdc Adj): ADN5-24-1PM-C & ADN10-24-1PM-C 24 Vdc (24-28 Vdc Adj): ADN20-24-1PM-C & ADN40-24-1PM-C Initial voltage setting 24.5 V ± 1% Hold-up time > 20 ms at full load (100 Vac Input @ Tamb = +25 °C) Voltage regulation < ± 2% (combination line, load, time and temperature related changes) Ripple < 50 mVpp: ADN5-24-1PM-C & ADN10-24-1PM-C < 100 mVpp: ADN20-24-1PM-C & ADN40-24-1PM-C Back EMF immunity < 35 Vdc Power Boost™ 1.5 x Nominal current for 2 or 4 seconds depending on model Short circuit current 1.5 x Nominal current at near zero volts at short circuit condition Parallel operation Switch selectable single unit or parallel unit operation. Units will not be damaged by parallel operation (regardless of switch position setting) Ouput noise suppression Radiated EMI values below EN61000-6-2 Overvoltage protection > 30.5 Vdc but < 33 Vdc, auto recovery Line and load regulation < 0.5% Time and temperature drift < 1% ADN-C Series Data Sheet General Specifications EMC emissions EN61000-6-2:2001, EN61000-6-3:2001, Class B EN55011, EN55022 Radiated and Conducted including Annex. A, EN61000-3-2 EMC immunity EN61000-6-1:2001, EN61000-6-2:2001, EN61000-4-2 Level 4, EN61000-4-3 Level 3, EN61000-4-6 Level 3, EN61000-4-4 Level 4 input and level 3 output. EN61000-4-5 Installation class 4, EN61000-4-11, IEC 61000-4-34 voltage dip immunity standard Warranty 5 Years General protection safety Protected against continuous short-circuit, continuous overload, continous open circuit. Protection Class 1 (IEC536), degree of protection IP20 (IEC60529) Safe low voltage: SELV (acc. IEC60950-1) Status indicators Visual: Three (3) status LEDs (Input, Output, Alarm) Relay: N.O. contact rated 200 mA/50 Vdc LED Diagnostics LED OK Loss of Ac Low Ac No Dc High Load Overload Hot Too Hot Input Green --- Yellow Green Green Green Green Green Output Green --- Green --- Yellow Yellow Green --- Alarm --- --- --- Red Yellow Red Yellow Yellow Environmental Specifications Storage temperature -40 °C to + 85 °C; All models Operating temperature From -25 °C to 70 °C. Derate starting at 60 °C; All models Up to 50% load permissable with horizontal or on top mounting orientation Other Features External fusing Not required. Unit provides internal fuse (not accessible) Mounting orientation Standard: Vertical, Optional: Horizontal or on Top Simple snap-on to DIN TS35/7.5 or TS35/15 rail system Ventilation Normal convection, No fan required Cooling spacing ADN5-24-1PM-C & ADN10-24-1PM-C: ADN20-24-1PM-C: ADN40-24-1PM-C: Connections Input: Screw terminals, connector size range: 16-10 AWG (1.5 - 6 mm2) for solid conductors Output:Two terminals per output, connector size range: 16-10 AWG (1.5 - 6 mm2) for solid conductors One terminal per output for ADC40-24-1PM-C, connector size range: 7-6 AWG (10.6 - 13 mm2) for solid conductors 15 mm in front, 25 mm above and below, 10 mm left and right 15 mm in front, 40 mm above and below, 10 mm left and right 15 mm in front, 25 mm above and below, 25 mm left and right ADN-C Series Data Sheet Ordering Information MTBF Model Number Power Input Voltage Weight Current Case Type ADN5-24-1PM-C 120 W 85-264 Vac 90-375 Vdc* 1.10 lbs (500 g) 5 A @ 24 Vdc Metal with mounting clip 550,000 hours ADN10-24-1PM-C 240 W 1.98 lbs (900 g) 10 A @ 24 Vdc Metal with mounting clip 550,000 hours ADN20-24-1PM-C 480 W 2.6 lbs (1200 g) 20 A @ 24 Vdc Metal with mounting clip 450,000 hours ADN40-24-1PM-C 960 W 6.0 lbs (2750 g) 40 A @ 24 Vdc Metal with mounting clip 500,000 hours 85-264 Vac 90-375 Vdc* 85-264 Vac 90-375 Vdc* 100-240 Vac Demonstrated at 40 °C *No UL listed for DC input Dimensions Height Width Depth ADN5-24-1PM-C 4.85 in (123 mm) 1.97 in (50 mm) 4.37 (111 mm) ADN10-24-1PM-C 4.85 in (123 mm) 2.36 in (60 mm) 4.37 (111 mm) ADN20-24-1PM-C 4.85 in (123 mm) 3.42 in (87 mm) 4.96 in (126 mm) ADN40-24-1PM-C 4.85 in (123 mm) 7.09 in (180 mm) 4.81 in (122 mm) Mechanical Drawing D W + - + OK 24 VDC / 5 A Input Output Alarm 22.5 - 28/5 Vdc Single H Parallel ADN5-24-1PM-C C U L US LISTED 115/230 V ~ 2.2/1.0 A 50/60 HZ N L WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] ADN-C DS 09Dec2015