NSC LM3875 Overturtm audio power amplifier series high-performance 56w audio power amplifier Datasheet

LM3875 Overture™ Audio Power Amplifier Series
High-Performance 56W Audio Power Amplifier
General Description
Features
The LM3875 is a high-performance audio power amplifier
capable of delivering 56W of continuous average power to
an 8Ω load with 0.1% THD+N from 20Hz to 20kHz.
n
n
n
n
The performance of the LM3875, utilizing its Self Peak Instantaneous Temperature (˚Ke) (SPiKe™) protection circuitry, puts it in a class above discrete and hybrid amplifiers
by providing an inherently, dynamically protected Safe Operating Area (SOA). SPiKe protection means that these
parts are completely safeguarded at the output against overvoltage, undervoltage, overloads, caused by shorts to the
supplies, thermal runaway, and instantaneous temperature
peaks.
The LM3875 maintains an excellent signal-to-noise ratio of
greater than 95dB(min) with a typical low noise floor of
2.0µV. It exhibits extremely low THD+N values of 0.06% at
the rated output into the rated load over the audio spectrum,
and provides excellent linearity with an IMD (SMPTE) typical
rating of 0.004%.
n
n
n
n
56W continuous average output power into 8Ω
100W instantaneous peak output power capability
Signal-to-Noise Ratio > 95dB (min)
Output protection from a short to ground or to the
supplies via internal current limiting circuitry
Output over-voltage protection against transients from
inductive loads
Supply under-voltage protection, not allowing internal
biasing to occur when |V+| + |V−| ≤ 12V, thus eliminating
turn-on and turn-off transients
11 lead TO-220 package
Wide supply voltage range: |V+| + |V−| = 20V to 84V
Applications
n
n
n
n
Component or compact stereos
Self-powered speakers
Surround-sound amplifiers
High-end stereo TVs
Typical Application
01144901
*Optional components dependent upon specific design requirements. Refer to the External Components Description section for a component function
description.
FIGURE 1. Typical Audio Amplifier Application Circuit
Overture™ and SPiKe™ are trademarks of National Semiconductor Corporation.
© 2004 National Semiconductor Corporation
DS011449
www.national.com
LM3875 Overture Audio Power Amplifier Series High-Performance 56W Audio Power Amplifier
August 2000
LM3875
Connection Diagram
Plastic Package (Note 8)
01144902
Top View
Order Number LM3875T or LM3875TF
See NS Package Number TA11B for
Staggered Lead Non-Isolated Package
or TF11B for Staggered Lead Isolated Package
Equivalent Schematic
(Excluding active protection circuitry)
01144906
www.national.com
2
Storage Temperature
(Notes 1,
−40˚C to +150˚C
Thermal Resistance
2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage |V+| + |V−| (No Signal)
Common Mode Input Voltage
Temperature Range
84V
+
1˚C/W
43˚C/W
Operating Ratings (Notes 1, 2)
94V
Supply Voltage |V+| + |V−| (Input
Signal)
θJC
θJA
TMIN ≤ TA ≤ TMAX
−
(V or V ) and
|V | + |V−| ≤ 80V
−20˚C ≤ TA ≤
+85˚C
+
Differential Input Voltage
Output Current
Supply Voltage |V+| + |V−|
60V
Internally Limited
Power Dissipation (Note 3)
125W
ESD Susceptibility (Note 4)
2500V
Junction Temperature (Note 5)
150˚C
Soldering Information
T package (10 seconds)
260˚C
20V to 84V
Note: Operation is guaranteed up to 84V, however, distortion may be introduced from the SPiKe Protection Circuitry when operating above 70V if
proper thermal considerations are not taken into account. Refer to the
Thermal Considerations section for more information. (See SPiKe Protection
Response)
Electrical Characteristics (Notes 1, 2)
The following specifications apply for V+ = +35V, V− = −35V with RL = 8Ω unless otherwise specified. Limits apply for TA =
25˚C.
LM3875
Symbol
Parameter
Conditions
|V+| + |V−|
Power Supply Voltage
**PO
Output Power (Continuous Average)
Peak PO
Instantaneous Peak Output Power
THD + N
Total Harmonic Distortion Plus Noise
40W, 20 Hz ≤ f ≤ 20 kHz
AV = 26 dB
**SR
Slew Rate (Note 9)
VIN = 1.414 Vrms, f = 10 kHz
Square-wave, RL = 2 kΩ
*I+
Total Quiescent Power Supply
Current
VCM = 0V, VO = 0V, Io = 0 mA
*VOS
Input Offset Voltage
IB
Input Bias Current
IOS
Io
THD + N = 0.1% (Max)
f = 1 kHz, f = 20 kHz
Typical
(Note 6)
56
Limit
(Note 7)
Units
(Limits)
20
84
V (Min)
V (Max)
40
W (Min)
100
W
0.06
%
11
5
V/µs
(Min)
30
70
mA (Max)
VCM = 0V, Io = 0 mA
1
10
mV (Max)
VCM = 0V, Io = 0 mA
0.2
1
µA (Max)
Input Offset Current
VCM = 0V, Io = 0 mA
0.01
0.2
µA (Max)
Output Current Limit
|V+| = |V−| = 10V, ton = 10 ms, VO = 0V
6
4
A(Min)
*Vod
Output Dropout Voltage
|V+−Vo−|, V+ = 20V, Io = +100 mA
|Vo−V−|, V− = −20V, Io = −100 mA
1.6
2.7
5
5
V (Max)
V (Max)
*PSRR
Power Supply Rejection Ratio
V+ = 40V to 20V, V− = −40V,
Vcm = 0V, Io = 0 mA
V+ = 40V, V = −40V to −20V,
Vcm = 0V, Io = 0 mA
120
120
85
85
dB (Min)
*CMRR
Common Mode Rejection Ratio
V+ = 60V to 20V, V− = −20V to −60V,
Vcm = 20V to −20V, Io = 0 mA
120
80
dB (Min)
*AVOL
Open Loop Voltage Gain
|V+| = |V−| = 40V, RL = 2 kΩ, ∆VO = 60V
120
90
dB (Min)
GBWP
Gain-Bandwidth Product
|V+| = |V−| = 40V
fO = 100 kHz, VIN = 50 mVrms
8
2
MHz
(Min)
**eIN
Input Noise
IHF − A Weighting Filter
RIN = 600Ω (Input Referred)
2.0
8.0
µV (Max)
3
www.national.com
LM3875
Absolute Maximum Ratings
LM3875
Electrical Characteristics (Notes 1, 2)
(Continued)
The following specifications apply for V+ = +35V, V− = −35V with RL = 8Ω unless otherwise specified. Limits apply for TA =
25˚C.
LM3875
Symbol
SNR
IMD
Parameter
Signal-to-Noise Ratio
Intermodulation Distortion Test
Conditions
Typical
(Note 6)
Limit
(Note 7)
Units
(Limits)
PO = 1W, A-Weighted,
Measured at 1 kHz, RS =25Ω
98 dB
dB
PO = 40W, A-Weighted,
Measured at 1 kHz, RS =25Ω
114 dB
dB
Ppk = 100W, A-Weighted,
Measured at 1 kHz, RS =25Ω
122 dB
dB
0.004
0.006
%
60 Hz, 7 kHz, 4:1 (SMPTE)
60 Hz, 7 kHz, 1:1 (SMPTE)
*DC Electrical Test; refer to Test Circuit #1.
**AC Electrical Test; refer to Test Circuit #2.
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 2: All voltages are measured with respect to supply GND, unless otherwise specified.
Note 3: For operating at case temperatures above 25˚C, the device must be derated based on a 150˚C maximum junction temperature and a thermal resistance
of θJC = 1.0˚C/W (junction to case). Refer to the Thermal Resistance figure in the Application Information section under Thermal Considerations.
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 5: The operating junction temperature maximum is 150˚C, however, the instantaneous Safe Operating Area temperature is 250˚C.
Note 6: Typicals are measured at 25˚C and represent the parametric norm.
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: The LM3875T package TA11B is a non-isolated package, setting the tab of the device and the heat sink at V− potential when the LM3875 is directly mounted
to the heat sink using only thermal compound. If a mica washer is used in addition to thermal compound, θCS (case to sink) is increased, but the heat sink will be
isolated from V−.
Note 9: The feedback compensation network limits the bandwidth of the closed-loop response and so the slew rate will be reduced due to the high frequency roll-off.
Without feedback compensation, the slew rate is typically 16V/µs.
Note 10: The output dropout voltage is the supply voltage minus the clipping voltage. Refer to the Clipping Voltage vs. Supply Voltage graph in the Typical
Performance Characteristics section.
Test Circuit #1
(DC Electrical Test Circuit)
01144903
www.national.com
4
LM3875
Test Circuit #2
(AC Electrical Test Circuit)
01144904
Single Supply Application Circuit
01144905
*Optional components dependent upon specific design requirements. Refer to the External Components Description section for a component function
description.
FIGURE 2. Typical Single Supply Audio Amplifier Application Circuit
5
www.national.com
LM3875
External Components Description
(Figure 1 and Figure 2)
Components
Functional Description
1.
RIN
Acts as a volume control by setting the voltage level allowed to the amplifier’s input terminals.
2.
RA
Provides DC voltage biasing for the single supply operation and bias current for the positive input terminal.
3.
CA
Provides bias filtering.
4.
C
Provides AC coupling at the input and output of the amplifier for single supply operation.
5.
RB
Prevents currents from entering the amplifier’s non-inverting input which may be passed through to the load
upon power-down of the system due to the low input impedance of the circuitry when the under-voltage
circuitry is off. This phenomenon occurs when the supply voltages are below 1.5V.
6.
*CC
Reduces the gain (bandwidth of the amplifier) at high frequencies to avoid quasi-saturation oscillations of the
output transistor. The capacitor also suppresses external electromagnetic switching noise created from
fluorescent lamps.
7.
Ri
Inverting input resistance to provide AC Gain in conjunction with Rf1.
8.
*Ci
Feedback capacitor. Ensures unity gain at DC. Also a low frequency pole (highpass roll-off) at:
9.
Rf1
Feedback resistance to provide AC Gain in conjunction with Ri.
10.
*Rf2
At higher frequencies feedback resistance works with Cf to provide lower AC Gain in conjunction with Rf1 and
Ri. A high frequency pole (lowpass roll-off) exists at:
fc = 1/(2π Ri Ci).
fc = [Rf1 Rf2] (s + 1/Rf2 Cf]/[(Rf1 + Rf2) (s + 1/Cf (Rf1 +Rf2))].
11.
*Cf
Compensation capacitor that works with Rf1 and Rf2 to reduce the AC Gain at higher frequencies.
12.
*RSN
Works with CSN to stabilize the output stage by creating a pole that eliminates high frequency oscillations.
13.
*CSN
Works with RSN to stabilize the output stage by creating a pole that eliminates high frequency oscillations.
= 1/(2πRSN CSN).
14.
*L
Provides high impedance at high frequencies so that R may decouple a highly capacitive load and reduce the
Q of the series resonant circuit due to capacitive load. Also provides a low impedance at low frequencies to
short out R and pass audio signals to the load.
15.
*R
16.
CS
fc
Provides power supply filtering and bypassing.
*Optional components dependent upon specific design requirements. Refer to the Application Information section for more information.
These two components act as low impedances to certain
frequencies which will couple signals from the input to the
output. Please take careful note of basic amplifier component functionality when designing in these components.
The optional external components shown in Figure 2 and
described above are applicable in both single and split voltage supply configurations.
OPTIONAL EXTERNAL COMPONENT INTERACTION
Although the optional external components have specific
desired functions that are designed to reduce the bandwidth
and eliminate unwanted high frequency oscillations they may
cause certain undesirable effects when they interact. Interaction may occur for components whose reactances are in
close proximity to one another. One example would be the
coupling capacitor, CC, and the compensation capacitor, Cf.
www.national.com
6
LM3875
Typical Performance Characteristics
SPiKe
Protection Response
Safe Area
01144918
01144917
Supply Current vs
Supply Voltage
Pulse Thermal Resistance
01144919
01144920
Supply Current vs
Output Voltage
Pulse Thermal Resistance
01144922
01144921
7
www.national.com
LM3875
Typical Performance Characteristics
(Continued)
Pulse Power Limit
Pulse Power Limit
01144923
01144924
Supply Current vs
Case Temperature
Clipping Voltage
vs Supply Voltage
01144925
01144926
Input Bias Current vs
Case Temperature
Peak Output Current
01144927
www.national.com
01144928
8
LM3875
Typical Performance Characteristics
(Continued)
THD + N vs
Output Power
THD + N vs Frequency
01144929
01144930
THD + N vs
Output Power
THD Distribution
01144931
01144932
Output Power vs
Load Resistance
THD Distribution
01144934
01144933
9
www.national.com
LM3875
Typical Performance Characteristics
(Continued)
Max Heatsink Thermal Resistance (˚C/W) at the Specified Ambient Temperature (˚C)
and Maximum Power Dissipation vs Supply Voltage
01144915
Note: The maximum heat sink thermal resistance values, ØSA, in the table above were calculated using a ØCS = 0.2˚C/W due to thermal compound.
Power Dissipation vs
Output Power
Power Dissipation vs
Output Power
01144935
01144936
Output Power vs
Supply Voltage
IMD 60 Hz, 4:1
01144937
www.national.com
01144938
10
LM3875
Typical Performance Characteristics
(Continued)
IMD 60 Hz, 7 kHz, 4:1
IMD 60 Hz, 7 kHz, 4:1
01144940
01144939
IMD 60 Hz, 1:1
IMD 60 Hz, 7 kHz, 1:1
01144941
01144942
Power Supply Rejection
Ratio
IMD 60 Hz, 7 kHz, 1:1
01144944
01144943
11
www.national.com
LM3875
Typical Performance Characteristics
(Continued)
Common-Mode Rejection
Ratio
Large Signal Response
01144945
01144946
Open Loop
Frequency Response
Pulse Response
01144947
01144948
Thermal Protection: The LM3875 has a sophisticated thermal protection scheme to prevent long-term thermal stress
to the device. When the temperature on the die reaches
165˚C, the LM3875 shuts down. It starts operating again
when the die temperature drops to about 155˚C, but if the
temperature again begins to rise, shutdown will occur again
at 165˚C. Therefore the device is allowed to heat up to a
relatively high temperature if the fault condition is temporary,
but a sustained fault will cause the device to cycle in a
Schmitt Trigger fashion between the thermal shutdown temperature limits of 165˚C and 155˚C. This greatly reduces the
stress imposed on the IC by thermal cycling, which in turn
improves its reliability under sustained fault conditions.
Since the die temperature is directly dependent upon the
heat sink, the heat sink should be chosen as discussed in
the Thermal Considerations section, such that thermal
shutdown will not be reached during normal operation. Using
the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of
any power semiconductor device.
Application Information
GENERAL FEATURES
Under-Voltage Protection: Upon system power-up the
under-voltage Protection Circuitry allows the power supplies
and their corresponding caps to come up close to their full
values before turning on the LM3875 such that no DC output
spikes occur. Upon turn-off, the output of the LM3875 is
brought to ground before the power supplies such that no
transients occur at power-down.
Over-Voltage Protection: The LM3875 contains overvoltage protection circuitry that limits the output current to approximately 4Apeak while also providing voltage clamping,
though not through internal clamping diodes. The clamping
effect is quite the same, however, the output transistors are
designed to work alternately by sinking large current spikes.
SPiKe Protection: The LM3875 is protected from instantaneous peak-temperature stressing by the power transistor
array. The Safe Operating Area graph in the Typical Performance Characteristics section shows the area of device
operation where the SPiKe Protection Circuitry is not enabled. The waveform to the right of the SOA graph exemplifies how the dynamic protection will cause waveform distortion when enabled.
www.national.com
12
mal compound on both faces. Two-mil mica washers are
most common, giving about 0.4˚C/W interface resistance
with the compound.
(Continued)
THERMAL CONSIDERATIONS
Silicone-rubber washers are also available. A 0.5˚C/W thermal resistance is claimed without thermal compound. Experience has shown that these rubber washers deteriorate and
must be replaced should the IC be dismounted.
Heat Sinking
The choice of a heat sink for a high-power audio amplifier is
made entirely to keep the die temperature at a level such
that the thermal protection circuitry does not operate under
normal circumstances. The heat sink should be chosen to
dissipate the maximum IC power for a given supply voltage
and rated load.
Determining Maximum Power Dissipation
Power dissipation within the integrated circuit package is a
very important parameter requiring a thorough understanding if optimum power output is to be obtained. An incorrect
maximum power dissipation (PD) calculation may result in
inadequate heatsinking, causing thermal shutdown circuitry
to operate and limit the output power.
With high-power pulses of longer duration than 100 ms, the
case temperature will heat up drastically without the use of a
heat sink. Therefore the case temperature, as measured at
the center of the package bottom, is entirely dependent on
heat sink design and the mounting of the IC to the heat sink.
For the design of a heat sink for your audio amplifier application refer to the Determining the Correct Heat Sink
section.
Since a semiconductor manufacturer has no control over
which heat sink is used in a particular amplifier design, we
can only inform the system designer of the parameters and
the method needed in the determination of a heat sink. With
this in mind, the system designer must choose his supply
voltages, a rated load, a desired output power level, and
know the ambient temperature surrounding the device.
These parameters are in addition to knowing the maximum
junction temperature and the thermal resistance of the IC,
both of which are provided by National Semiconductor.
As a benefit to the system designer we have provided Maximum Power Dissipation vs Supply Voltages curves for various loads in the Typical Performance Characteristics section, giving an accurate figure for the maximum thermal
resistance required for a particular amplifier design. This
data was based on θJC = 1˚C/W and θCS = 0.2˚C/W. We also
provide a section regarding heat sink determination for any
audio amplifier design where θCS may be a different value. It
should be noted that the idea behind dissipating the maximum power within the IC is to provide the device with a low
resistance to convection heat transfer such as a heat sink.
Therefore, it is necessary for the system designer to be
conservative in his heat sink calculations. As a rule, the
lower the thermal resistance of the heat sink the higher the
amount of power that may be dissipated. This is, of course,
guided by the cost and size requirements of the system.
Convection cooling heat sinks are available commercially,
and their manufacturers should be consulted for ratings.
Proper mounting of the IC is required to minimize the thermal
drop between the package and the heat sink. The heat sink
must also have enough metal under the package to conduct
heat from the center of the package bottom to the fins
without excessive temperature drop.
A thermal grease such as Wakefield type 120 or Thermalloy
Thermacote should be used when mounting the package to
the heat sink. Without this compound, the thermal resistance
will be no better than 0.5˚C/W, and probably much worse.
With the compound, thermal resistance will be 0.2˚C/W or
less, assuming under 0.005 inch combined flatness runout
for the package and heat sink. Proper torquing of the mounting bolts is important and can be determined from heat sink
manufacturer’s specification sheets.
Should it be necessary to isolate V− from the heat sink, an
insulating washer is required. Hard washers like berylum
oxide, anodized aluminum and mica require the use of ther-
The following equations can be used to accurately calculate
the maximum and average integrated circuit power dissipation for your amplifier design, given the supply voltage, rated
load, and output power. These equations can be directly
applied to the Power Dissipation vs Output Power curves in
the Typical Performance Characteristics section.
Equation (1) exemplifies the maximum power dissipation of
the IC and Equations (2), (3) exemplify the average IC power
dissipation expressed in different forms.
(1)
PDMAX = VCC2/2π2 RL
where VCC is the total supply voltage
(2)
PDAVE = (VOpk/RL) [VCC/π − VOpk/2]
where VCC is the total supply voltage and VOpk = VCC/π
(3)
PDAVE = VCC VOpk/π RL − VOpk2/2 RL
where VCC is the total supply voltage.
Determining the Correct Heat Sink
Once the maximum IC power dissipation is known for a
given supply voltage, rated load, and the desired rated output power the maximum thermal resistance (in ˚C/W) of a
heat sink can be calculated. This calculation is made using
Equation (4) and is based on the fact that thermal heat flow
parameters are analogous to electrical current flow properties.
It is also known that typically the thermal resistance, θJC
(junction to case), of the LM3875 is 1˚C/W and that using
Thermalloy Thermacote thermal compound provides a thermal resistance, θCS (case to heat sink), of about 0.2˚C/W as
explained in the Heat Sinking section.
Referring to the figure below, it is seen that the thermal
resistance from the die (junction) to the outside air (ambient)
is a combination of three thermal resistances, two of which
are known, θJC and θCS. Since convection heat flow (power
dissipation) is analogous to current flow, thermal resistance
is analogous to electrical resistance, and temperature drops
are analogous to voltage drops, the power dissipation out of
the LM3875 is equal to the following:
PDMAX = (TJmax − TAmb)/θJA
where θJA = θJC + θCS + θSA
01144910
13
www.national.com
LM3875
Application Information
LM3875
Application Information
(Continued)
But since we know PDMAX, θJC, and θSC for the application
and we are looking for θSA, we have the following:
θSA = [(TJmax − TAmb) − PDMAX (θJC + θCS)]/PDMAX (4)
Again it must be noted that the value of θSA is dependent
upon the system designer’s amplifier application and its
corresponding parameters as described previously. If the
ambient temperature that the audio amplifier is to be working
under is higher than the normal 25˚C, then the thermal
resistance for the heat sink, given all other things are equal,
will need to be smaller.
RMS reading,
average responding,
3.
4.
peak reading, and
quasi peak reading.
Although theoretical noise analysis is derived using true
RMS based calculations, most actual measurements are
taken with ARM (Average Responding Meter) test equipment.
Typical signal-to-noise figures are listed for an A-weighted
filter which is commonly used in the measurement of noise.
The shape of all weighting filters is similar, with the peak of
the curve usually occurring in the 3 kHz–7 kHz region as
shown below.
Equations (1), (4) are the only equations needed in the
determination of the maximum heat sink thermal resistance.
This is, of course, given that the system designer knows the
required supply voltages to drive his rated load at a particular
power output level and the parameters provided by the
semiconductor manufacturer. These parameters are the
junction to case thermal resistance, θJC, TJmax = 150˚C, and
the recommended Thermalloy Thermacote thermal compound resistance, θCS.
SIGNAL-TO-NOISE RATIO
In the measurement of the signal-to-noise ratio, misinterpretations of the numbers actually measured are common. One
amplifier may sound much quieter than another, but due to
improper testing techniques, they appear equal in measurements. This is often the case when comparing integrated
circuit designs to discrete amplifier designs. Discrete transistor amps often “run out of gain” at high frequencies and
therefore have small bandwidths to noise as indicated below.
01144912
SUPPLY BYPASSING
The LM3875 has excellent power supply rejection and does
not require a regulated supply. However, to eliminate possible oscillations all op amps and power op amps should
have their supply leads bypassed with low-inductance capacitors having short leads and located close to the package
terminals. Inadequate power supply bypassing will manifest
itself by a low frequency oscillation known as “motorboating”
or by high frequency instabilities. These instabilities can be
eliminated through multiple bypassing utilizing a large tantalum or electrolytic capacitor (10 µF or larger) which is used to
absorb low frequency variations and a small ceramic capacitor (0.1 µF) to prevent any high frequency feedback through
the power supply lines.
If adequate bypassing is not provided the current in the
supply leads which is a rectified component of the load
current may be fed back into internal circuitry. This signal
causes low distortion at high frequencies requiring that the
supplies be bypassed at the package terminals with an
electrolytic capacitor of 470 µF or more.
01144911
Integrated circuits have additional open loop gain allowing
additional feedback loop gain in order to lower harmonic
distortion and improve frequency response. It is this additional bandwidth that can lead to erroneous signal-to-noise
measurements if not considered during the measurement
process. In the typical example above, the difference in
bandwidth appears small on a log scale but the factor of 10
in bandwidth, (200 kHz to 2 MHz) can result in a 10 dB
theoretical difference in the signal-to-noise ratio (white noise
is proportional to the square root of the bandwidth in a
system).
In comparing audio amplifiers it is necessary to measure the
magnitude of noise in the audible bandwidth by using a
“weighting” filter (Note 11). A “weighting” filter alters the
frequency response in order to compensate for the average
human ear’s sensitivity to the frequency spectra. The weighting filters at the same time provide the bandwidth limiting as
discussed in the previous paragraph.
LEAD INDUCTANCE
Power op amps are sensitive to inductance in the output
lead, particularly with heavy capacitive loading. Feedback to
the input should be taken directly from the output terminal,
minimizing common inductance with the load.
Lead inductance can also cause voltage surges on the supplies. With long leads to the power supply, energy is stored in
the lead inductance when the output is shorted. This energy
can be dumped back into the supply bypass capacitors when
the short is removed. The magnitude of this transient is
reduced by increasing the size of the bypass capacitor near
the IC. With at least a 20 µF local bypass, these voltage
surges are important only if the lead length exceeds a couple
feet ( > 1 µH lead inductance). Twisting together the supply
and ground leads minimizes the effect.
Note 11: CCIR/ARM: A Practical Noise Measurement Method; by Ray
Dolby, David Robinson and Kenneth Gundry, AES Preprint No. 1353 (F-3).
In addition to noise filtering, differing meter types give different noise readings. Meter responses include:
www.national.com
1.
2.
14
LM3875
Application Information
(Continued)
LAYOUT, GROUND LOOPS AND STABILITY
The LM3875 is designed to be stable when operated at a
closed-loop gain of 10 or greater, but as with any other
high-current amplifier, the LM3875 can be made to oscillate
under certain conditions. These usually involve printed circuit board layout or output/input coupling.
When designing a layout, it is important to return the load
ground, the output compensation ground, and the low level
(feedback and input) grounds to the circuit board common
ground point through separate paths. Otherwise, large currents flowing along a ground conductor will generate voltages on the conductor which can effectively act as signals at
the input, resulting in high frequency oscillation or excessive
distortion. It is advisable to keep the output compensation
components and the 0.1 µF supply decoupling capacitors as
close as possible to the LM3875 to reduce the effects of PCB
trace resistance and inductance. For the same reason, the
ground return paths should be as short as possible.
In general, with fast, high-current circuitry, all sorts of problems can arise from improper grounding which again can be
avoided by returning all grounds separately to a common
point. Without isolating the ground signals and returning the
grounds to a common point, ground loops may occur.
“Ground Loop” is the term used to describe situations occurring in ground systems where a difference in potential exists
between two ground points. Ideally a ground is a ground, but
unfortunately, in order for this to be true, ground conductors
with zero resistance are necessary. Since real world ground
leads possess finite resistance, currents running through
them will cause finite voltage drops to exist. If two ground
return lines tie into the same path at different points there will
be a voltage drop between them. The first figure below
shows a common ground example where the positive input
ground and the load ground are returned to the supply
ground point via the same wire. The addition of the finite wire
resistance, R2, results in a voltage difference between the
two points as shown below.
01144913
The load current IL will be much larger than input bias current
I1, thus V1 will follow the output voltage directly, i.e., in
phase. Therefore the voltage appearing at the non-inverting
input is effectively positive feedback and the circuit may
oscillate. If there were only one device to worry about then
the values of R1 and R2 would probably be small enough to
be ignored; however, several devices normally comprise a
total system. Any ground return of a separate device, whose
output is in phase, can feedback in a similar manner and
cause instabilities. Out of phase ground loops also are
troublesome, causing unexpected gain and phase errors.
The solution to most ground loop problems is to always use
a single-point ground system, although this is sometimes
impractical. The third figure above is an example of a singlepoint ground system.
The single-point ground concept should be applied rigorously to all components and all circuits when possible. Violations of single-point grounding are most common among
printed circuit board designs, since the circuit is surrounded
by large ground areas which invite the temptation to run a
device to the closest ground spot. As a final rule, make all
ground returns low resistance and low inductance by using
large wire and wide traces.
Occasionally, current in the output leads (which function as
antennas) can be coupled through the air to the amplifier
input, resulting in high-frequency oscillation. This normally
happens when the source impedance is high or the input
leads are long. The problem can be eliminated by placing a
small capacitor, CC, (on the order of 50 pF–500 pF) across
the LM3875 input terminals. Refer to the External Components Description section relating to component interaction
with Cf.
REACTIVE LOADING
It is hard for most power amplifiers to drive highly capacitive
loads very effectively and normally results in oscillations or
ringing on the square wave response. If the output of the
LM3875 is connected directly to a capacitor with no series
15
www.national.com
LM3875
Application Information
spond as quickly to nonlinearities. This decreased ability to
respond to nonlinearities increases the THD + N specification.
The desired input impedance is set by RIN. Very high values
can cause board layout problems and DC offsets at the
output. The value for the feedback resistance, Rf1, should be
chosen to be a relatively large value (10 kΩ–100 kΩ), and
the other feedback resistance, Ri, is calculated using standard op amp configuration gain equations. Most audio amplifiers are designed from the non-inverting amplifier configuration.
(Continued)
resistance, the square wave response will exhibit ringing if
the capacitance is greater than about 0.2 µF. If highly capacitive loads are expected due to long speaker cables, a
method commonly employed to protect amplifiers from low
impedances at high frequencies is to couple to the load
through a 10Ω resistor in parallel with a 0.7 µH inductor. The
inductor-resistor combination as shown in the Typical Application Circuit isolates the feedback amplifier from the
load by providing high output impedance at high frequencies
thus allowing the 10Ω resistor to decouple the capacitive
load and reduce the Q of the series resonant circuit. The LR
combination also provides low output impedance at low
frequencies thus shorting out the 10Ω resistor and allowing
the amplifier to drive the series RC load (large capacitive
load due to long speaker cables) directly.
DESIGN A 40W/8Ω AUDIO AMPLIFIER
Given:
Power Output
Load Impedance
GENERALIZED AUDIO POWER AMPLIFIER DESIGN
The system designer usually knows some of the following
parameters when starting an audio amplifier design:
Desired Power Output
Input Impedance
Maximum Supply Voltage
1V(max)
Input Impedance
100 kΩ
20 Hz–20 kHz ± 0.25 dB
Equations (5), (6) give:
Iopeak = 3.16A
40W/8Ω
Vopeak = 25.3V
±
Therefore the supply required is: 30.3V @3.16A
With 15% regulation and high line the final supply voltage is
± 38.3V using Equation (7). At this point it is a good idea to
check the Power Output vs Supply Voltage to ensure that the
required output power is obtainable from the device while
maintaining low THD + N. It is also good to check the Power
Dissipation vs Supply Voltage to ensure that the device can
handle the internal power dissipation. At the same time
designing in a relatively practical sized heat sink with a low
thermal resistance is also important. Refer to Typical Performance Characteristics graphs and the Thermal Considerations section for more information.
The minimum gain from Equation (8) is: AV ≥ 18
We select a gain of 21 (Non-Inverting Amplifier); resulting in
a sensitivity of 894 mV.
Letting RIN equal 100 kΩ gives the required input impedance, however, this would eliminate the “volume control”
unless an additional input impedance was placed in series
with the 10 kΩ potentiometer that is depicted in Figure 1.
Adding the additional 100 kΩ resistor would ensure the
minimum required input impedance.
For low DC offsets at the output we let Rf1 = 100 kΩ. Solving
for Ri (Non-Inverting Amplifier) gives the following:
Ri = Rf1/(AV − 1) = 100k/(21 − 1) = 5 kΩ; use 5.1 kΩ
The bandwidth requirement must be stated as a pole, i.e.,
the 3 dB frequency. Five times away from a pole give
0.17 dB down, which is better than the required 0.25 dB.
Therefore:
fL = 20 Hz/5 = 4 Hz
fH = 20 kHz x 5 = 100 kHz
At this point, it is a good idea to ensure that the Gain
Bandwidth Product for the part will provide the designed gain
out to the upper 3 dB point of 100 kHz. This is why the
minimum GBWP of the LM3875 is important.
GBWP = AV x f3 dB = 21 x 100 kHz = 2.1 MHz
GBWP = 2.0 MHz (min) for LM3875
Solving for the low frequency roll-off capacitor, Ci, we have:
Ci > 1/(2π Ri fL) = 7.8 µF; use 10 µF.
Load Impedance
Bandwidth
The power output and load impedance determine the power
supply requirements, however, depending upon the application some system designers may be limited to certain maximum supply voltages. If the designer does have a power
supply limitation, he should choose a practical load impedance which would allow the amplifier to provide the desired
output power, keeping in mind the current limiting capabilities of the device. In any case, the output signal swing and
current are found from (where PO is the average output
power):
(5)
(6)
To determine the maximum supply voltage the following
parameters must be considered. Add the dropout voltage
(5 volts for LM3875) to the peak output swing, Vopeak, to get
the supply rail value, (i.e. + Vopeak + Vod) at a current of
Iopeak). The regulation of the supply determines the unloaded
voltage, usually about 15% higher. Supply voltage will also
rise 10% during high line conditions. Therefore, the maximum supply voltage is obtained from the following equation:
max. supplies ≈ ± (Vopeak + Vod(1 + regulation)(1.1) (7)
The input sensitivity and the output power specs determine
the minimum required gain as depicted below:
(8)
Normally the gain is set between 20 and 200; for a 40W, 8Ω
audio amplifier this results in a sensitivity of 894 mV and
89 mV, respectively. Although higher gain amplifiers provide
greater output power and dynamic headroom capabilities,
there are certain shortcomings that go along with the so
called “gain”. The input referred noise floor is increased and
hence the SNR is worse. With the increase in gain, there is
also a reduction of the power bandwidth which results in a
decrease in feedback thus not allowing the amplifier to rewww.national.com
8Ω
Input Level
Bandwidth
Input Level
40W
16
Input Offset Voltage: The absolute value of the voltage
which must be applied between the input terminals through
two equal resistances to obtain zero output voltage and
current.
Input Bias Current: The absolute value of the average of
the two input currents with the output voltage and current at
zero.
Input Offset Current: The absolute value of the difference
in the two input currents with the output voltage and current
at zero.
Input Common-Mode Voltage Range (or Input Voltage
Range): The range of voltages on the input terminals for
which the amplifier is operational. Note that the specifications are not guaranteed over the full common-mode voltage
range unless specifically stated.
Output-Current Limit: The output current with a fixed output voltage and a large input overdrive. The limiting current
drops with time once SPiKe protection circuitry is activated.
Output Saturation Threshold (Clipping Point): The output
swing limit for a specified input drive beyond that required for
zero output. It is measured with respect to the supply to
which the output is swinging.
Common-Mode Rejection: The ratio of the input commonmode voltage range to the peak-to-peak change in input
offset voltage over this range.
Power Supply Rejection: The ratio of the change in input
offset voltage to the change in power supply voltages producing it.
Quiescent Supply Current: The current required from the
power supply to operate the amplifier with no load and the
output voltage and current at zero.
Slew Rate: The internally limited rate of change in output
voltage with a large amplitude step function applied to the
input.
Class B Amplifier: The most common type of audio power
amplifier that consists of two output devices each of which
conducts for 180˚ of the input cycle. The LM3875 is a
Quasi-AB type amplifier.
Crossover Distortion: Distortion caused in the output stage
of a class B amplifier. It can result from inadequate bias
current providing a dead zone where the output does not
respond to the input as the input cycle goes through its zero
crossing point. Also for ICs an inadequate frequency response of the output PNP device can cause a turn-on delay
giving crossover distortion on the negative going transistion
through zero crossing at the higher audio frequencies.
THD + N: Total Harmonic Distortion plus Noise refers to the
measurement technique in which the fundamental component is removed by a bandreject (notch) filter and all remaining energy is measured including harmonics and noise.
Signal-to-Noise Ratio: The ratio of a system’s output signal
level to the system’s output noise level obtained in the
absence of a signal. The output reference signal is either
specified or measured at a specified distortion level.
Continuous Average Output Power: The minimum sine
wave continuous average power output in watts (or dBW)
that can be delivered into the rated load, over the rated
bandwidth, at the rated maximum total harmonic distortion.
Music Power: A measurement of the peak output power
capability of an amplifier with either a signal duration sufficiently short that the amplifier power supply does not sag
during the measurement, or when high quality external
power supplies are used. This measurement (an IHF standard) assumes that with normal music program material the
amplifier power supplies will sag insignificantly.
Peak Power: Most commonly referred to as the power output capability of an amplifier that can be delivered to the
load; specified by the part’s maximum voltage swing.
Output Resistance: The ratio of the change in output voltage to the change in output current with the output around
zero.
Power Dissipation Rating: The power that can be dissipated for a specified time interval without activating the
protection circuitry. For time intervals in excess of 100 ms,
dissipation capability is determined by heat sinking of the IC
package rather than by the IC itself.
Thermal Resistance: The peak, junction-temperature rise,
per unit of internal power dissipation (units in ˚C/W), above
the case temperature as measured at the center of the
package bottom.
The DC thermal resistance applies when one output transistor is operating continuously. The AC thermal resistance
applies with the output transistors conducting alternately at a
high enough frequency that the peak capability of neither
transistor is exceeded.
Power Bandwidth: The power bandwidth of an audio amplifier is the frequency range over which the amplifier voltage
gain does not fall below 0.707 of the flat band voltage gain
specified for a given load and output power.
Power bandwidth also can be measured by the frequencies
at which a specified level of distortion is obtained while the
amplifier delivers a power output 3 dB below the rated output. For example, an amplifier rated at 60W with ≤0.25%
THD + N, would make its power bandwidth measured as the
difference between the upper and lower frequencies at which
0.25% distortion was obtained while the amplifier was delivering 30W.
Gain-Bandwidth Product: The Gain-Bandwidth Product is
a way of predicting the high-frequency usefulness of an op
amp. The Gain-Bandwidth Product is sometimes called the
unity-gain frequency or unity-gain cross frequency because
the open-loop gain characteristic passes through or crosses
unity gain at this frequency. Simply, we have the following
relationship:
ACL1 x f1 = ACL2 x f2
Assuming that at unity-gain
(ACL1 = 1 or 0 dB) fu = f1 = GBWP,
then we have the following:
GBWP = ACL2 x f2
This says that once fu (GBWP) is known for an amplifier,
then the open-loop gain can be found at any frequency. This
17
www.national.com
LM3875
Headroom: The margin between an actual signal operating
level (usually the power rating of the amplifier with particular
supply voltages, a rated load value, and a rated THD + N
figure) and the level just before clipping distortion occurs,
expressed in decibels.
Large Signal Voltage Gain: The ratio of the output voltage
swing to the differential input voltage required to drive the
output from zero to either swing limit. The output swing limit
is the supply voltage less a specified quasi-saturation voltage. A pulse of short enough duration to minimize thermal
effects is used as a measurement signal.
Definition of Terms
LM3875
Definition of Terms
This refers to a weighted noise measurement for a Dolby B
type noise reduction system. A filter characteristic is used
that gives a closer correlation of the measurement with the
subjective annoyance of noise to the ear. Measurements
made with this filter cannot necessarily be related to unweighted noise measurements by some fixed conversion
factor since the answers obtained will depend on the spectrum of the noise source.
(Continued)
is also an excellent equation to determine the 3 dB point of a
closed-loop gain, assuming that you know the GBWP of the
device. Refer to the diagram below.
Bi-amplification: The technique of splitting the audio frequency spectrum into two sections and using individual
power amplifiers to drive a separate woofer and tweeter.
Crossover frequencies for the amplifiers usually vary between 500 Hz and 1600 Hz. “Biamping” has the advantages
of allowing smaller power amps to produce a given sound
pressure level and reducing distortion effects produced by
overdrive in one part of the frequency spectrum affecting the
other part.
C.C.I.R./A.R.M.:
Literally: International Radio Consultative
Average Responding Meter
S.P.L.: Sound Pressure Level — usually measured with a
microphone/meter combination calibrated to a pressure level
of 0.0002 µBars (approximately the threshold hearing level).
S.P.L. = 20 Log 10P/0.0002 dB
Where P is the R.M.S sound pressure in microbars. (1 Bar =
1 atmosphere = 14.5 lb./in2 = 194 dB S.P.L.).
Committee
01144914
FIGURE 3.
www.national.com
18
LM3875
Physical Dimensions
inches (millimeters) unless otherwise noted
Order Number LM3875T
NS Package Number TA11B
Order Number LM3875TF
NS Package Number TF11B
19
www.national.com
LM3875 Overture Audio Power Amplifier Series High-Performance 56W Audio Power Amplifier
Notes
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the body, or
(b) support or sustain life, and whose failure to perform when
properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or
system, or to affect its safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship
Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned
Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: [email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: [email protected]
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560