Ecliptek E32D1EEA1K-155.520MTR Oscillator Datasheet

E32D1 Series
E32D1
• RoHS Compliant (Pb-Free)
• PECL Output Oscillators
• 3.3V supply voltage
• Ceramic 6-pad SMD Package
• Stability to ±25ppm
• Tri-State Output
• Complementary Output
• Available on Tape and Reel
H
L
W
2.0
7.0
5.0
OSCILLATOR
ELECTRICAL SPECIFICATIONS
50, 51.84, 52, 52.08, 54, 57.1429, 61.44, 63.36, 65.536, 76.8, 77.76, 100, 104, 106.25, 125,
126.72, 128, 153.6, 155.52, 156.25, 159.375, 161.1328, 166.6286, 167.3315, 184.32, 186.666MHz
Operating Temperature Range
0°C to 70°C
-40°C to 85°C
Storage Temperature Range
-55°C to 125°C
Supply Voltage (VCC)
3.3VDC ±5%
Input Current
100mA Maximum
With Load
Frequency Tolerance / Stability
Inclusive of all conditions: Calibration Tolerance at 25°C, ±50ppm or ±25ppm Maximum
Frequency Stability over the Operating Temperature
Range, Supply Voltage Change, Output Load Change, 1st
Year Aging, Shock, and Vibration
Output Voltage Logic High (VOH)
VCC-1.025VDC Minimum
Output Voltage Logic Low (VOL)
VCC-1.620VDC Maximum
Rise Time / Fall Time
1.5 nSeconds Maximum
20% to 80% of waveform
Duty Cycle
50 ±10(%)
at 50% of waveform
50 ±5(%)
Load Drive Capability
50 Ohms into VCC-2.0VDC
Control Voltage (VC)
1.65VDC ±1.65VDC
Test Conditions for Frequency Deviation
Control Voltage Range (VCR)
0.0VDC to VCC +0.5VDC
Frequency Deviation
±75ppm Minimum
Inclusive of Operating Temperature Range, Supply
Voltage Change, and Output Load Change
Linearity
20%, 15%, or 10% Maximum
Transfer Function
Positive Transfer Characteristic
Modulation Bandwidth (MBW)
10kHz Minimum
Measured at -3dB with Contol Voltage of +1.65VDC
Input Impedance (ZI)
50kOhms Typical
Typical Phase Noise (Fo = 155.520MHz) at 10Hz Offset
-55dBc/Hz
-90dBc/Hz
at 100Hz Offset
-120dBc/Hz
at 1kHz Offset
-140dBc/Hz
at 10kHz Offset
-145dBc/Hz
at 100kHz Offset
-148dBc/Hz
at 1MHz Offset
Logic Control/Additional Output
Tri-State Enable Low / Complementary Output
Tri-State Input Voltage
Disables Outputs: High Impedance
VIH of 70% of VCC Minimum
Enables Output
No Connection
Enables Output
VIL of 30% of VCC Maximum
RMS Phase Jitter
0.4pSec Typical, 1pSec Maximum
FJ = 12kHz to 20MHz
Accumulated Period Jitter (tacc)
4pSec Typical, 5pSec Maximum
Sigma of Total Jitter Distribution
Period Jitter (trj)
3pSec Typical, 5pSec Maximum
Sigma of Random Jitter
Period Jitter (trms)
3pSec Typical, 5pSec Maximum
Sigma of Total Jitter Distribution
Period Jitter (tdj)
4pSec Typical, 10pSec Maximum
Deterministic Jitter
Period Jitter (tp-p)
27pSec Typical, 40pSec Maximum
Peak to Peak of Jitter Distribution
Start Up Time
10 mSeconds Maximum
Frequency Range (MHz)
MANUFACTURER
CATEGORY
ECLIPTEK CORP.
OSCILLATOR
SERIES
PACKAGE
VOLTAGE
CLASS
REV.DATE
E32D1
CERAMIC
3.3V
OS3Y
01/09
800-ECLIPTEK www.ecliptek.com for latest revision
Specifications subject to change without notice.
PART NUMBERING GUIDE
E32D1 E E A 2 K - 155.520M TR
FREQUENCY TOLERANCE & STABILITY/
OPERATING TEMPERATURE RANGE
D=±50ppm Maximum over 0°C to +70°C
E=±25ppm Maximum over 0°C to +70°C
H=±50ppm Maximum over -40°C to +85°C
AVAILABLE OPTIONS
Blank=Bulk
TR=Tape and Reel (Standard)
FREQUENCY DEVIATION
E=±75ppm Minimum
LOGIC CONTROL / ADDITIONAL OUTPUT
K=Tri-State (Enable Low) / Complementary Output
LINEARITY
A=20% Maximum
B=15% Maximum
C=10% Maximum
DUTY CYCLE
1=50% ±10%
2=50% ±5%
FREQUENCY
MECHANICAL DIMENSIONS
SUGGESTED SOLDER PAD LAYOUT
ALL DIMENSIONS IN MILLIMETERS
ALL DIMENSIONS IN MILLIMETERS
Pin 1: Voltage Control
Pin 2: Tri-State
Pin 3: Case Ground
Pin 4: Output
Pin 5: Complementary Output
Pin 6: Supply Voltage
Tolerances= +0.1
TAPE AND REEL DIMENSIONS
ALL DIMENSIONS IN MILLIMETERS
TAPE
A
B
C
D
E
16±.3-.1
7.5±.1
6.75±.1
4 ±.1
2±.1
F
G
H
J
K
8±.1
B0*
1.5 +.1-0
A0*
.3 ±.05
F
M
N
O
P
Q
1.5 MIN
50 MIN
20.2 MIN
13±.2
40 MIN
QTY/REEL
1,000
REEL
L
K0*
R
S
T
U
V
2.5 MIN
10 MIN
22.4 MAX
360 MAX
16.4+2-0
*Compliant to EIA 481A
ENVIRONMENTAL/MECHANICAL SPECIFICATIONS
MARKING SPECIFICATIONS
Line 1: ECLIPTEK
Characteristic
Specification
Fine Leak Test
Gross Leak Test
Mechanical Shock
Vibration
Solderability
Temperature Cycling
Resistance to Soldering Heat
Resistance to Solvents
MIL-STD-883, Method 1014, Condition A
MIL-STD-883, Method 1014, Condition C
MIL-STD-202, Method 213, Condition C
MIL-STD-883, Method 2007, Condition A
MIL-STD-883, Method 2002
MIL-STD-883, Method 1010
MIL-STD-202, Method 210
MIL-STD-202, Method 215
Line 2: XX.XXX M
Frequency in MHz (5 Digits Maximum + Decimal)
Line 3: XX Y ZZ
Week of Year
Last Digit of Year
Ecliptek Manufacturing Identifier
MANUFACTURER
CATEGORY
SERIES
PACKAGE
VOLTAGE
CLASS
ECLIPTEK CORP.
OSCILLATOR
E32D1
CERAMIC
3.3V
OS3Y
800-ECLIPTEK www.ecliptek.com for latest revision
REV.DATE
01/09
Specifications subject to change without notice.
Similar pages