MOTOROLA Order this document by MCM6264C/D SEMICONDUCTOR TECHNICAL DATA 8K x 8 Bit Fast Static RAM MCM6264C The MCM6264C is fabricated using Motorola’s high–performance silicon–gate CMOS technology. Static design eliminates the need for external clocks or timing strobes, while CMOS circuitry reduces power consumption and provides for greater reliability. This device meets JEDEC standards for functionality and pinout, and is available in plastic dual–in–line and plastic small–outline J–leaded packages. Single 5 V ± 10% Power Supply Fully Static — No Clock or Timing Strobes Necessary Fast Access Times: 12, 15, 20, 25, and 35 ns Equal Address and Chip Enable Access Times Output Enable (G) Feature for Increased System Flexibility and to Eliminate Bus Contention Problems • Low Power Operation: 110 – 150 mA Maximum AC • Fully TTL Compatible — Three State Output P PACKAGE 300 MIL PLASTIC CASE 710B–01 • • • • • BLOCK DIAGRAM A2 VCC VSS A3 A4 A5 A7 ROW DECODER MEMORY MATRIX 256 ROWS x 32 x 9 COLUMNS A8 A9 A11 DQ0 INPUT DATA CONTROL DQ7 E1 E2 W G COLUMN I/O COLUMN DECODER A0 A1 A6 A10 A12 J PACKAGE 300 MIL SOJ CASE 810B–03 PIN ASSIGNMENT NC 1 28 VCC A12 2 27 W A7 3 26 E2 A6 4 25 A8 A5 5 24 A9 A4 6 23 A11 A3 7 22 G A2 8 21 A10 A1 9 20 E1 A0 10 19 DQ7 DQ0 11 18 DQ6 DQ1 12 17 DQ5 DQ2 13 16 DQ4 VSS 14 15 DQ3 PIN NAMES A0 – A12 . . . . . . . . . . . . . Address Input DQ0 – DQ7 . . . Data Input/Data Output W . . . . . . . . . . . . . . . . . . . . Write Enable G . . . . . . . . . . . . . . . . . . . Output Enable E1, E2 . . . . . . . . . . . . . . . . . Chip Enable VCC . . . . . . . . . . . Power Supply (+ 5 V) VSS . . . . . . . . . . . . . . . . . . . . . . . Ground REV 2 5/95 Motorola, Inc. 1995 MOTOROLA FAST SRAM MCM6264C 1 TRUTH TABLE (X = Don’t Care) E1 E2 G W Mode VCC Current Output Cycle H X L L L X L H H H X X H L X X X H H L Not Selected Not Selected Output Disabled Read Write ISB1, ISB2 ISB1, ISB2 ICCA ICCA ICCA High–Z High–Z High–Z Dout High–Z — — — Read Cycle Write Cycle ABSOLUTE MAXIMUM RATINGS (See Note) Rating Symbol Value Unit VCC – 0.5 to + 7.0 V Vin, Vout – 0.5 to VCC + 0.5 V Output Current Iout ± 20 mA Power Dissipation PD 1.0 W Temperature Under Bias Tbias – 10 to + 85 °C Operating Temperature TA 0 to + 70 °C Power Supply Voltage Voltage Relative to VSS for Any Pin Except VCC This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to these high–impedance circuits. This CMOS memory circuit has been designed to meet the dc and ac specifications shown in the tables, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow of at least 500 linear feet per minute is maintained. Storage Temperature — Plastic Tstg – 55 to + 125 °C NOTE: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to RECOMMENDED OPERATING CONDITIONS. Exposure to higher than recommended voltages for extended periods of time could affect device reliability. DC OPERATING CONDITIONS AND CHARACTERISTICS (VCC = 5.0 V ± 10%, TA = 0 to +70°C, Unless Otherwise Noted) RECOMMENDED OPERATING CONDITIONS Parameter Symbol Min Typ Max Unit Supply Voltage (Operating Voltage Range) VCC 4.5 5.0 5.5 V Input High Voltage VIH 2.2 — VCC + 0.3** V Input Low Voltage VIL – 0.5* — 0.8 V Symbol Min Max Unit Input Leakage Current (All Inputs, Vin = 0 to VCC) Ilkg(I) — ±1 µA Output Leakage Current (E1 = VIH, E2 = VIL, or G = VIH, Vout = 0 to VCC) Ilkg(O) — ±1 µA * VIL (min) = – 0.5 V dc; VIL (min) = – 2.0 V ac (pulse width ≤ 20 ns) ** VIH (max) = VCC + 0.3 V dc; VIH (max) = VCC + 2 V ac (pulse width ≤ 20 ns) DC CHARACTERISTICS Parameter Output Low Voltage (IOL = 8.0 mA) VOL — 0.4 V Output High Voltage (IOH = – 4.0 mA) VOH 2.4 — V POWER SUPPLY CURRENTS Parameter Symbol – 12 – 15 – 20 – 25 – 35 Unit AC Active Supply Current (Iout = 0 mA, VCC = Max, f = fmax) ICCA 150 140 130 120 110 mA AC Standby Current (E1 = VIH or E2 = VIL, VCC = Max, f = fmax) ISB1 45 40 35 30 30 mA Standby Current (E1 ≥ VCC – 0.2 V or E2 ≤ VSS + 0.2 V, Vin ≤ VSS + 0.2 V or ≥ VCC – 0.2 V) ISB2 20 20 20 20 20 mA CAPACITANCE (f = 1 MHz, dV = 3 V, TA = 25°C, Periodically Sampled Rather Than 100% Tested) Symbol Max Unit Address Input Capacitance Cin 6 pF Control Pin Input Capacitance (E1, E2, G, W) Cin 6 pF I/O Capacitance CI/O 7 pF Parameter MCM6264C 2 MOTOROLA FAST SRAM AC OPERATING CONDITIONS AND CHARACTERISTICS (VCC = 5.0 V ± 10%, TA = 0 to + 70°C, Unless Otherwise Noted) Input Timing Measurement Reference Level . . . . . . . . . . . . . . . 1.5 V Input Pulse Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 3.0 V Input Rise/Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 ns Output Timing Measurement Reference Level . . . . . . . . . . . . . 1.5 V Output Load . . . . . . . . . . . . See Figure 1A Unless Otherwise Noted READ CYCLE (See Notes 1 and 2) – 12 Parameter – 15 – 20 – 25 – 35 Symbol Min Max Min Max Min Max Min Max Min Max Unit Notes Read Cycle Time tAVAV 12 — 15 — 20 — 25 — 35 — ns 3 Address Access Time tAVQV — 12 — 15 — 20 — 25 — 35 ns Enable Access Time tELQV — 12 — 15 — 20 — 25 — 35 ns Output Enable Access Time tGLQV — 6 — 8 — 10 — 11 — 12 ns Output Hold from Address Change tAXQX 4 — 4 — 4 — 4 — 4 — ns Enable Low to Output Active tELQX 4 — 4 — 4 — 4 — 4 — ns 5, 6 ,7 Enable High to Output High–Z tEHQZ 0 6 0 8 0 9 0 10 0 11 ns 5, 6, 7 Output Enable Low to Output Active tGLQX 0 — 0 — 0 — 0 — 0 — ns 5, 6, 7 Output Enable High to Output High–Z tGHQZ 0 6 0 7 0 8 0 9 0 10 ns 5, 6, 7 Power Up Time tELICCH 0 — 0 — 0 — 0 — 0 — ns Power Down Time tEHICCL — 12 — 15 — 20 — 25 — 35 ns 4 NOTES: 1. W is high for read cycle. 2. E1 and E2 are represented by E in this data sheet. E2 is of opposite polarity to E. 3. All timings are referenced from the last valid address to the first transitioning address. 4. Addresses valid prior to or coincident with E going low. 5. At any given voltage and temperature, tEHQZ (max) is less than tELQX (min), and tGHQZ (max) is less than tGLQX (min), both for a given device and from device to device. 6. Transition is measured ± 500 mV from steady–state voltage with load of Figure 1B. 7. This parameter is sampled and not 100% tested. 8. Device is continuously selected (E1 = VIL, E2 = VIH, G = VIL). TIMING LIMITS AC TEST LOADS +5V 480 Ω OUTPUT Z0 = 50 Ω 50 Ω OUTPUT 255 Ω 5 pF VL = 1.5 V Figure 1A MOTOROLA FAST SRAM Figure 1B The table of timing values shows either a minimum or a maximum limit for each parameter. Input requirements are specified from the external system point of view. Thus, address setup time is shown as a minimum since the system must supply at least that much time (even though most devices do not require it). On the other hand, responses from the memory are specified from the device point of view. Thus, the access time is shown as a maximum since the device never provides data later than that time. MCM6264C 3 READ CYCLE 1 (See Note 8) tAVAV A (ADDRESS) tAXQX Q (DATA OUT) PREVIOUS DATA VALID DATA VALID tAVQV READ CYCLE 2 (See Note 4) tAVAV A (ADDRESS) tAVQV tELQV E (CHIP ENABLE) tEHQZ tELQX G (OUTPUT ENABLE) tGHQZ tGLQV tGLQX Q (DATA OUT) VCC ICC SUPPLY CURRENT ISB MCM6264C 4 HIGH–Z tELICCH HIGH–Z DATA VALID tEHICCL MOTOROLA FAST SRAM WRITE CYCLE 1 (W Controlled, See Notes 1, 2, and 3) – 12 Parameter Write Cycle Time – 15 – 20 – 25 – 35 Symbol Min Max Min Max Min Max Min Max Min Max Unit Notes tAVAV 12 — 15 — 20 — 25 — 35 — ns 4 Address Setup Time tAVWL 0 — 0 — 0 — 0 — 0 — ns Address Valid to End of Write tAVWH 10 — 12 — 15 — 17 — 20 — ns Write Pulse Width tWLWH, tWLEH 10 — 12 — 15 — 17 — 20 — ns Write Pulse Width, G High tWLWH, tWLEH 8 — 10 — 12 — 15 — 17 — ns Data Valid to End of Write tDVWH 6 — 7 — 8 — 10 — 12 — ns Data Hold Time tWHDX 0 — 0 — 0 — 0 — 0 — ns Write Low to Output High–Z tWLQZ 0 6 0 7 0 8 0 10 0 12 ns 6, 7, 8 Write High to Output Active tWHQX 4 — 4 — 4 — 4 — 4 — ns 6, 7, 8 5 Write Recovery Time tWHAX 0 — 0 — 0 — 0 — 0 — ns NOTES: 1. A write occurs during the overlap of E low and W low. 2. E1 and E2 are represented by E in this data sheet. E2 is of opposite polarity to E. 3. If G goes low coincident with or after W goes low, the output will remain in a high impedance state. 4. All timings are referenced from the last valid address to the first transitioning address. 5. If G ≥ VIH, the output will remain in a high impedance state. 6. At any given voltage and temperature, tWLQZ (max) is less than tWHQX (min), both for a given device and from device to device. 7. Transition is measured ± 500 mV from steady–state voltage with load of Figure 1B. 8. This parameter is sampled and not 100% tested. WRITE CYCLE 1 (W Controlled, See Notes 1, 2, and 3) tAVAV A (ADDRESS) tWHAX tAVWH E (CHIP ENABLE) tWLWH tWLEH W (WRITE ENABLE) tDVWH tAVWL D (DATA IN) DATA VALID tWLQZ Q (DATA OUT) MOTOROLA FAST SRAM tWHDX HIGH–Z tWHQX HIGH–Z MCM6264C 5 WRITE CYCLE 2 (E Controlled, See Notes 1 and 2) – 12 Parameter – 15 – 20 – 25 – 35 Symbol Min Max Min Max Min Max Min Max Min Max Unit Notes Write Cycle Time tAVAV 12 — 15 — 20 — 25 — 35 — ns 3 Address Setup Time tAVEL 0 — 0 — 0 — 0 — 0 — ns Address Valid to End of Write tAVEH 12 — 12 — 15 — 20 — 25 — ns Enable to End of Write tELEH, tELWH 10 — 10 — 12 — 15 — 25 — ns Write Pulse Width tWLEH 10 — 12 — 15 — 17 — 20 — ns Data Valid to End of Write tDVEH 7 — 7 — 8 — 10 — 15 — ns Data Hold Time tEHDX 0 — 0 — 0 — 0 — 0 — ns Write Recovery Time tEHAX 0 — 0 — 0 — 0 — NOTES: 1. A write occurs during the overlap of E low and W low. 2. E1 and E2 are represented by E in this data sheet. E2 is of opposite polarity to E. 3. All timings are referenced from the last valid address to the first transitioning address. 4. If E goes low coincident with or after W goes low, the output will remain in a high impedance state. 5. If E goes high coincident with or before W goes high, the output will remain in a high impedance state. 0 — ns 4, 5 WRITE CYCLE 2 (E Controlled, See Notes 1 and 2) tAVAV A (ADDRESS) tAVEH E (CHIP ENABLE) tAVEL tWLEH tELEH tELWH tEHAX W (WRITE ENABLE) tDVEH D (DATA IN) tEHDX DATA VALID HIGH–Z Q (DATA OUT) ORDERING INFORMATION (Order by Full Part Number) MCM 6264C X XX XX Motorola Memory Prefix Shipping Method (R2 = Tape and Reel, Blank = Rails) Part Number Speed (12 = 12 ns, 15 = 15 ns, 20 = 20 ns, 25 = 25 ns, 35 = 35 ns) Package (P = 300 mil Plastic, J = 300 mil SOJ) Full Part Numbers — MCM6264CP12 MCM6264CP15 MCM6264CP20 MCM6264CP25 MCM6264CP35 MCM6264C 6 MCM6264CJ12 MCM6264CJ15 MCM6264CJ20 MCM6264CJ25 MCM6264CJ35 MCM6264CJ12R2 MCM6264CJ15R2 MCM6264CJ20R2 MCM6264CJ25R2 MCM6264CJ35R2 MOTOROLA FAST SRAM PACKAGE DIMENSIONS 28 LEAD 300 MIL PDIP CASE 710B–01 -A- 28 15 1 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION A AND B DOES NOT INCLUDE MOLD FLASH. MAXIMUM MOLD FLASH 0.25 (0.010). -B- DIM A B C D E F G J K L M N L C -T- K SEATING PLANE E F N G D 28 PL 0.25 (0.010) M J 28 PL M T A 0.25 (0.010) S T B M MILLIMETERS MIN MAX 34.55 34.79 7.12 7.62 3.81 4.57 0.39 0.53 1.27 BSC 1.15 1.39 2.54 BSC 0.21 0.30 3.18 3.42 7.62 BSC 0° 15° 0.51 1.01 INCHES MIN MAX 1.360 1.370 0.280 0.300 0.150 0.180 0.015 0.021 0.050 BSC 0.045 0.055 0.100 BSC 0.008 0.012 0.125 0.135 0.300 BSC 0° 15° 0.020 0.040 S 28 LEAD 300 MIL SOJ CASE 810B–03 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. DIMENSION A & B DO NOT INCLUDE MOLD PROTRUSION. MOLD PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 3. CONTROLLING DIMENSION: INCH. 4. DIM R TO BE DETERMINED AT DATUM -T-. 5. 810B-01 AND -02 OBSOLETE, NEW STANDARD 810B-03. F DETAIL Z 28 15 N 1 D 24 PL 14 0.18 (0.007) -A- M T A 0.18 (0.007) H BRK S S T B S P -B- L G M M E C 0.10 (0.004) K DETAIL Z -T- SEATING PLANE S RAD R 0.25 (0.010) S T B S DIM A B C D E F G H K L M N P R S MILLIMETERS MIN MAX 18.29 18.54 7.74 7.50 3.75 3.26 0.50 0.39 2.48 2.24 0.81 0.67 1.27 BSC 0.50 — 1.14 0.89 0.64 BSC 0° 10° 1.14 0.76 8.64 8.38 6.86 6.60 1.01 0.77 INCHES MIN MAX 0.720 0.730 0.295 0.305 0.128 0.148 0.015 0.020 0.088 0.098 0.026 0.032 0.050 BSC 0.020 — 0.035 0.045 0.025 BSC 0° 10° 0.030 0.045 0.330 0.340 0.260 0.270 0.030 0.040 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. MOTOROLA FAST SRAM MCM6264C 7 Literature Distribution Centers: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. JAPAN: Nippon Motorola Ltd.; 4–32–1, Nishi–Gotanda, Shinagawa–ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. MCM6264C 8 ◊ CODELINE TO BE PLACED HERE *MCM6264C/D* MCM6264C/D MOTOROLA FAST SRAM